From: Rustam Adilov <adilov@disroot.org>
To: Vinod Koul <vkoul@kernel.org>,
Neil Armstrong <neil.armstrong@linaro.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Stanley Chang <stanley_chang@realtek.com>,
linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Rustam Adilov <adilov@disroot.org>,
Michael Zavertkin <misha.zavertkin@mail.ru>
Subject: [PATCH v2 1/6] phy: realtek: usb2: introduce vstatus/new_reg_req variables to driver data
Date: Fri, 27 Mar 2026 21:06:33 +0500 [thread overview]
Message-ID: <20260327160638.15134-2-adilov@disroot.org> (raw)
In-Reply-To: <20260327160638.15134-1-adilov@disroot.org>
In RTL9607C SoC, the vstatus register is located at a certain offset from
the base and so introduce the vstatus_offset to handle it.
Busy bit of the vstatus and new_reg_req bit are also different and so
introduce these variables to the driver data as well.
Add these variables to the pre-existing phy cfg structs for RTD SoCs and
assign them the default values.
Co-developed-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
drivers/phy/realtek/phy-rtk-usb2.c | 59 ++++++++++++++++++++++++------
1 file changed, 48 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
index 248550ef98ca..f5d2f0c3376a 100644
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -64,6 +64,9 @@ struct phy_reg {
void __iomem *reg_wrap_vstatus;
void __iomem *reg_gusb2phyacc0;
int vstatus_index;
+ int vstatus_offset;
+ int vstatus_busy;
+ int new_reg_req;
};
struct phy_data {
@@ -96,6 +99,9 @@ struct phy_cfg {
bool do_toggle_driving;
bool use_default_parameter;
bool is_double_sensitivity_mode;
+ int vstatus_offset;
+ int vstatus_busy;
+ int new_reg_req;
};
struct phy_parameter {
@@ -162,21 +168,21 @@ static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
addr -= OFFEST_PHY_READ;
/* polling until VBusy == 0 */
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return (char)ret;
/* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return (char)ret;
/* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return (char)ret;
@@ -194,25 +200,25 @@ static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
int ret = 0;
/* write data to VStatusOut2 (data output to phy) */
- writel((u32)data << shift_bits, reg_wrap_vstatus);
+ writel((u32)data << shift_bits, reg_wrap_vstatus + phy_reg->vstatus_offset);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return ret;
/* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return ret;
/* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return ret;
@@ -957,6 +963,7 @@ static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
static int parse_phy_data(struct rtk_phy *rtk_phy)
{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
struct device *dev = rtk_phy->dev;
struct device_node *np = dev->of_node;
struct phy_parameter *phy_parameter;
@@ -974,6 +981,9 @@ static int parse_phy_data(struct rtk_phy *rtk_phy)
phy_parameter->phy_reg.reg_wrap_vstatus = of_iomap(np, 0);
phy_parameter->phy_reg.reg_gusb2phyacc0 = of_iomap(np, 1) + index;
phy_parameter->phy_reg.vstatus_index = index;
+ phy_parameter->phy_reg.vstatus_offset = phy_cfg->vstatus_offset;
+ phy_parameter->phy_reg.vstatus_busy = phy_cfg->vstatus_busy;
+ phy_parameter->phy_reg.new_reg_req = phy_cfg->new_reg_req;
if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
phy_parameter->inverse_hstx_sync_clock = true;
@@ -1085,6 +1095,9 @@ static const struct phy_cfg rtd1295_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1395_phy_cfg = {
@@ -1109,6 +1122,9 @@ static const struct phy_cfg rtd1395_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1395_phy_cfg_2port = {
@@ -1133,6 +1149,9 @@ static const struct phy_cfg rtd1395_phy_cfg_2port = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1619_phy_cfg = {
@@ -1155,6 +1174,9 @@ static const struct phy_cfg rtd1619_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1319_phy_cfg = {
@@ -1181,6 +1203,9 @@ static const struct phy_cfg rtd1319_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1312c_phy_cfg = {
@@ -1206,6 +1231,9 @@ static const struct phy_cfg rtd1312c_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1619b_phy_cfg = {
@@ -1231,6 +1259,9 @@ static const struct phy_cfg rtd1619b_phy_cfg = {
.driving_updated_for_dev_dis = 0x8,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1319d_phy_cfg = {
@@ -1256,6 +1287,9 @@ static const struct phy_cfg rtd1319d_phy_cfg = {
.driving_updated_for_dev_dis = 0x8,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1315e_phy_cfg = {
@@ -1282,6 +1316,9 @@ static const struct phy_cfg rtd1315e_phy_cfg = {
.driving_updated_for_dev_dis = 0x8,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct of_device_id usbphy_rtk_dt_match[] = {
--
2.53.0
WARNING: multiple messages have this Message-ID (diff)
From: Rustam Adilov <adilov@disroot.org>
To: Vinod Koul <vkoul@kernel.org>,
Neil Armstrong <neil.armstrong@linaro.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Stanley Chang <stanley_chang@realtek.com>,
linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Rustam Adilov <adilov@disroot.org>,
Michael Zavertkin <misha.zavertkin@mail.ru>
Subject: [PATCH v2 1/6] phy: realtek: usb2: introduce vstatus/new_reg_req variables to driver data
Date: Fri, 27 Mar 2026 21:06:33 +0500 [thread overview]
Message-ID: <20260327160638.15134-2-adilov@disroot.org> (raw)
In-Reply-To: <20260327160638.15134-1-adilov@disroot.org>
In RTL9607C SoC, the vstatus register is located at a certain offset from
the base and so introduce the vstatus_offset to handle it.
Busy bit of the vstatus and new_reg_req bit are also different and so
introduce these variables to the driver data as well.
Add these variables to the pre-existing phy cfg structs for RTD SoCs and
assign them the default values.
Co-developed-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
drivers/phy/realtek/phy-rtk-usb2.c | 59 ++++++++++++++++++++++++------
1 file changed, 48 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
index 248550ef98ca..f5d2f0c3376a 100644
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -64,6 +64,9 @@ struct phy_reg {
void __iomem *reg_wrap_vstatus;
void __iomem *reg_gusb2phyacc0;
int vstatus_index;
+ int vstatus_offset;
+ int vstatus_busy;
+ int new_reg_req;
};
struct phy_data {
@@ -96,6 +99,9 @@ struct phy_cfg {
bool do_toggle_driving;
bool use_default_parameter;
bool is_double_sensitivity_mode;
+ int vstatus_offset;
+ int vstatus_busy;
+ int new_reg_req;
};
struct phy_parameter {
@@ -162,21 +168,21 @@ static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
addr -= OFFEST_PHY_READ;
/* polling until VBusy == 0 */
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return (char)ret;
/* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return (char)ret;
/* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return (char)ret;
@@ -194,25 +200,25 @@ static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
int ret = 0;
/* write data to VStatusOut2 (data output to phy) */
- writel((u32)data << shift_bits, reg_wrap_vstatus);
+ writel((u32)data << shift_bits, reg_wrap_vstatus + phy_reg->vstatus_offset);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return ret;
/* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return ret;
/* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
- val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
writel(val, reg_gusb2phyacc0);
- ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
if (ret)
return ret;
@@ -957,6 +963,7 @@ static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
static int parse_phy_data(struct rtk_phy *rtk_phy)
{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
struct device *dev = rtk_phy->dev;
struct device_node *np = dev->of_node;
struct phy_parameter *phy_parameter;
@@ -974,6 +981,9 @@ static int parse_phy_data(struct rtk_phy *rtk_phy)
phy_parameter->phy_reg.reg_wrap_vstatus = of_iomap(np, 0);
phy_parameter->phy_reg.reg_gusb2phyacc0 = of_iomap(np, 1) + index;
phy_parameter->phy_reg.vstatus_index = index;
+ phy_parameter->phy_reg.vstatus_offset = phy_cfg->vstatus_offset;
+ phy_parameter->phy_reg.vstatus_busy = phy_cfg->vstatus_busy;
+ phy_parameter->phy_reg.new_reg_req = phy_cfg->new_reg_req;
if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
phy_parameter->inverse_hstx_sync_clock = true;
@@ -1085,6 +1095,9 @@ static const struct phy_cfg rtd1295_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1395_phy_cfg = {
@@ -1109,6 +1122,9 @@ static const struct phy_cfg rtd1395_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1395_phy_cfg_2port = {
@@ -1133,6 +1149,9 @@ static const struct phy_cfg rtd1395_phy_cfg_2port = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1619_phy_cfg = {
@@ -1155,6 +1174,9 @@ static const struct phy_cfg rtd1619_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = false,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1319_phy_cfg = {
@@ -1181,6 +1203,9 @@ static const struct phy_cfg rtd1319_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1312c_phy_cfg = {
@@ -1206,6 +1231,9 @@ static const struct phy_cfg rtd1312c_phy_cfg = {
.driving_updated_for_dev_dis = 0xf,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1619b_phy_cfg = {
@@ -1231,6 +1259,9 @@ static const struct phy_cfg rtd1619b_phy_cfg = {
.driving_updated_for_dev_dis = 0x8,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1319d_phy_cfg = {
@@ -1256,6 +1287,9 @@ static const struct phy_cfg rtd1319d_phy_cfg = {
.driving_updated_for_dev_dis = 0x8,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct phy_cfg rtd1315e_phy_cfg = {
@@ -1282,6 +1316,9 @@ static const struct phy_cfg rtd1315e_phy_cfg = {
.driving_updated_for_dev_dis = 0x8,
.use_default_parameter = false,
.is_double_sensitivity_mode = true,
+ .vstatus_offset = 0,
+ .vstatus_busy = PHY_VSTS_BUSY,
+ .new_reg_req = PHY_NEW_REG_REQ,
};
static const struct of_device_id usbphy_rtk_dt_match[] = {
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
next prev parent reply other threads:[~2026-03-27 16:07 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-03-27 16:06 [PATCH v2 0/6] phy: realtek: usb2: support for RTL9607C USB2 PHY Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov [this message]
2026-03-27 16:06 ` [PATCH v2 1/6] phy: realtek: usb2: introduce vstatus/new_reg_req variables to driver data Rustam Adilov
2026-03-27 16:06 ` [PATCH v2 2/6] phy: realtek: usb2: introduce read and write functions " Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov
2026-03-30 21:19 ` Vladimir Oltean
2026-03-30 21:19 ` Vladimir Oltean
2026-03-30 21:32 ` Vladimir Oltean
2026-03-30 21:32 ` Vladimir Oltean
2026-03-31 16:26 ` Rustam Adilov
2026-03-31 16:26 ` Rustam Adilov
2026-03-31 16:34 ` Michael Zavertkin
2026-03-31 16:34 ` Michael Zavertkin
2026-03-31 16:51 ` Michael Zavertkin
2026-03-31 15:45 ` Rustam Adilov
2026-03-31 15:45 ` Rustam Adilov
2026-03-27 16:06 ` [PATCH v2 3/6] dt-bindings: phy: realtek,usb2phy.yaml: extend for resets and RTL9607C support Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov
2026-03-27 16:06 ` [PATCH v2 4/6] phy: realtek: usb2: introduce reset controller struct Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov
2026-03-30 21:39 ` Vladimir Oltean
2026-03-30 21:39 ` Vladimir Oltean
2026-03-31 16:35 ` Rustam Adilov
2026-03-31 16:35 ` Rustam Adilov
2026-03-27 16:06 ` [PATCH v2 5/6] phy: realtek: usb2: add support for RTL9607C USB2 PHY Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov
2026-03-30 21:50 ` Vladimir Oltean
2026-03-30 21:50 ` Vladimir Oltean
2026-03-31 16:48 ` Rustam Adilov
2026-03-31 16:48 ` Rustam Adilov
2026-03-31 19:36 ` Vladimir Oltean
2026-03-31 19:36 ` Vladimir Oltean
2026-04-01 14:16 ` Rustam Adilov
2026-04-01 14:16 ` Rustam Adilov
2026-03-27 16:06 ` [PATCH v2 6/6] phy: realtek: usb2: Make configs available for MACH_REALTEK_RTL Rustam Adilov
2026-03-27 16:06 ` Rustam Adilov
2026-03-30 21:52 ` Vladimir Oltean
2026-03-30 21:52 ` Vladimir Oltean
2026-03-31 16:48 ` Rustam Adilov
2026-03-31 16:48 ` Rustam Adilov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260327160638.15134-2-adilov@disroot.org \
--to=adilov@disroot.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=misha.zavertkin@mail.ru \
--cc=neil.armstrong@linaro.org \
--cc=robh@kernel.org \
--cc=stanley_chang@realtek.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.