From: Chris Morgan <macroalpha82@gmail.com>
To: linux-iio@vger.kernel.org
Cc: andy@kernel.org, nuno.sa@analog.com, dlechner@baylibre.com,
jic23@kernel.org, jean-baptiste.maneyrol@tdk.com,
linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org,
heiko@sntech.de, conor+dt@kernel.org, krzk+dt@kernel.org,
robh@kernel.org, andriy.shevchenko@intel.com,
Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V12 5/9] iio: imu: inv_icm42607: Add PM support for icm42607
Date: Thu, 11 Jun 2026 15:26:02 -0500 [thread overview]
Message-ID: <20260611202607.85376-6-macroalpha82@gmail.com> (raw)
In-Reply-To: <20260611202607.85376-1-macroalpha82@gmail.com>
From: Chris Morgan <macromorgan@hotmail.com>
Add power management support for the ICM42607 device driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
drivers/iio/imu/inv_icm42607/inv_icm42607.h | 18 +++
.../iio/imu/inv_icm42607/inv_icm42607_core.c | 131 ++++++++++++++++++
.../iio/imu/inv_icm42607/inv_icm42607_i2c.c | 1 +
.../iio/imu/inv_icm42607/inv_icm42607_spi.c | 1 +
4 files changed, 151 insertions(+)
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607.h b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
index c85d3b74166f..28edc12d5373 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607.h
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
@@ -9,6 +9,7 @@
#include <linux/bits.h>
#include <linux/iio/iio.h>
#include <linux/mutex.h>
+#include <linux/pm.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/time.h>
@@ -105,11 +106,19 @@ struct inv_icm42607_hw {
u8 whoami;
};
+struct inv_icm42607_suspended {
+ enum inv_icm42607_sensor_mode gyro;
+ enum inv_icm42607_sensor_mode accel;
+ bool temp;
+};
+
/**
* struct inv_icm42607_state - driver state variables
* @hw: Hardware specific data.
* @map: regmap pointer.
* @vddio_supply: I/O voltage regulator for the chip.
+ * @suspended: suspended sensors configuration.
+ * @vddio_en: I/O voltage status for runtime PM.
* @lock: lock for serializing multiple registers access.
* @conf: chip sensors configurations.
* @orientation: sensor chip orientation relative to main hardware.
@@ -118,6 +127,8 @@ struct inv_icm42607_state {
const struct inv_icm42607_hw *hw;
struct regmap *map;
struct regulator *vddio_supply;
+ struct inv_icm42607_suspended suspended;
+ bool vddio_en;
struct mutex lock;
struct inv_icm42607_conf conf;
struct iio_mount_matrix orientation;
@@ -339,11 +350,18 @@ struct inv_icm42607_state {
#define INV_ICM42607_GYRO_STARTUP_TIME_MS 30
#define INV_ICM42607_TEMP_STARTUP_TIME_MS 77
+/*
+ * Suspend delay assumed from other icm42600 series device, not
+ * documented in datasheet.
+ */
+#define INV_ICM42607_SUSPEND_DELAY_MS (2 * USEC_PER_MSEC)
+
typedef int (*inv_icm42607_bus_setup)(struct inv_icm42607_state *);
extern const struct regmap_config inv_icm42607_regmap_config;
extern const struct inv_icm42607_hw inv_icm42607_hw_data;
extern const struct inv_icm42607_hw inv_icm42607p_hw_data;
+extern const struct dev_pm_ops inv_icm42607_pm_ops;
int inv_icm42607_core_probe(struct regmap *regmap,
const struct inv_icm42607_hw *hw,
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
index 5d40f1ee53d6..8073317088ec 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
@@ -11,6 +11,7 @@
#include <linux/iio/iio.h>
#include <linux/module.h>
#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/time.h>
@@ -102,6 +103,56 @@ const struct inv_icm42607_hw inv_icm42607p_hw_data = {
};
EXPORT_SYMBOL_NS_GPL(inv_icm42607p_hw_data, "IIO_ICM42607");
+static int inv_icm42607_set_pwr_mgmt0(struct inv_icm42607_state *st,
+ enum inv_icm42607_sensor_mode gyro,
+ enum inv_icm42607_sensor_mode accel,
+ bool temp, unsigned int *sleep_ms)
+{
+ enum inv_icm42607_sensor_mode oldaccel = st->conf.accel.mode;
+ enum inv_icm42607_sensor_mode oldgyro = st->conf.gyro.mode;
+ bool oldtemp = st->conf.temp_en;
+ unsigned int sleepval_ms;
+ unsigned int val;
+ int ret;
+
+ if (gyro == oldgyro && accel == oldaccel && temp == oldtemp)
+ return 0;
+
+ val = FIELD_PREP(INV_ICM42607_PWR_MGMT0_GYRO_MODE_MASK, gyro);
+ val |= FIELD_PREP(INV_ICM42607_PWR_MGMT0_ACCEL_MODE_MASK, accel);
+ /*
+ * Note that temp being enabled here doesn't affect PM since
+ * per 10.25 of the datasheet the clock will be off by default
+ * if both the gyro and accel modes are off.
+ */
+ if (!temp)
+ val |= INV_ICM42607_PWR_MGMT0_ACCEL_LP_CLK_SEL;
+ ret = regmap_write(st->map, INV_ICM42607_REG_PWR_MGMT0, val);
+ if (ret)
+ return ret;
+
+ st->conf.gyro.mode = gyro;
+ st->conf.accel.mode = accel;
+ st->conf.temp_en = temp;
+
+ sleepval_ms = 0;
+ if (temp && !oldtemp)
+ sleepval_ms = max(sleepval_ms, INV_ICM42607_TEMP_STARTUP_TIME_MS);
+
+ if (accel != oldaccel)
+ sleepval_ms = max(sleepval_ms, INV_ICM42607_ACCEL_STARTUP_TIME_MS);
+
+ if (gyro != oldgyro)
+ sleepval_ms = max(sleepval_ms, INV_ICM42607_GYRO_STARTUP_TIME_MS);
+
+ if (sleep_ms)
+ *sleep_ms = sleepval_ms;
+ else if (sleepval_ms)
+ fsleep(sleepval_ms * USEC_PER_MSEC);
+
+ return 0;
+}
+
static int inv_icm42607_set_conf(struct inv_icm42607_state *st,
const struct inv_icm42607_conf *conf)
{
@@ -213,12 +264,17 @@ static int inv_icm42607_enable_vddio_reg(struct inv_icm42607_state *st)
{
int ret;
+ if (st->vddio_en)
+ return 0;
+
ret = regulator_enable(st->vddio_supply);
if (ret)
return ret;
fsleep(INV_ICM42607_POWER_UP_TIME_US);
+ st->vddio_en = true;
+
return 0;
}
@@ -226,7 +282,12 @@ static void inv_icm42607_disable_vddio_reg(void *_data)
{
struct inv_icm42607_state *st = _data;
+ if (!st->vddio_en)
+ return;
+
regulator_disable(st->vddio_supply);
+
+ st->vddio_en = false;
}
int inv_icm42607_core_probe(struct regmap *regmap,
@@ -241,6 +302,8 @@ int inv_icm42607_core_probe(struct regmap *regmap,
if (!st)
return -ENOMEM;
+ dev_set_drvdata(dev, st);
+
ret = devm_mutex_init(dev, &st->lock);
if (ret)
return ret;
@@ -276,10 +339,78 @@ int inv_icm42607_core_probe(struct regmap *regmap,
if (ret)
return ret;
+ ret = devm_pm_runtime_set_active_enabled(dev);
+ if (ret)
+ return ret;
+
+ pm_runtime_set_autosuspend_delay(dev, INV_ICM42607_SUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(dev);
+
return 0;
}
EXPORT_SYMBOL_NS_GPL(inv_icm42607_core_probe, "IIO_ICM42607");
+static int inv_icm42607_suspend(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ return ret;
+
+ inv_icm42607_disable_vddio_reg(st);
+
+ return 0;
+}
+
+static int inv_icm42607_resume(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret;
+
+ ret = inv_icm42607_enable_vddio_reg(st);
+ if (ret)
+ return ret;
+
+ return pm_runtime_force_resume(dev);
+}
+
+static int inv_icm42607_runtime_suspend(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+
+ guard(mutex)(&st->lock);
+
+ /* save sensors state */
+ st->suspended.gyro = st->conf.gyro.mode;
+ st->suspended.accel = st->conf.accel.mode;
+ st->suspended.temp = st->conf.temp_en;
+
+ return inv_icm42607_set_pwr_mgmt0(st, INV_ICM42607_SENSOR_MODE_OFF,
+ INV_ICM42607_SENSOR_MODE_OFF, false,
+ NULL);
+}
+
+static int inv_icm42607_runtime_resume(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+
+ guard(mutex)(&st->lock);
+
+ /* restore sensors state */
+ return inv_icm42607_set_pwr_mgmt0(st, st->suspended.gyro,
+ st->suspended.accel,
+ st->suspended.temp, NULL);
+}
+
+EXPORT_NS_GPL_DEV_PM_OPS(inv_icm42607_pm_ops, IIO_ICM42607) = {
+ SYSTEM_SLEEP_PM_OPS(inv_icm42607_suspend, inv_icm42607_resume)
+ RUNTIME_PM_OPS(inv_icm42607_runtime_suspend,
+ inv_icm42607_runtime_resume,
+ NULL)
+};
+
MODULE_AUTHOR("InvenSense, Inc.");
MODULE_DESCRIPTION("InvenSense ICM-42607 device driver");
MODULE_LICENSE("GPL");
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
index a1484f32c5d9..6e7310db5598 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
@@ -85,6 +85,7 @@ static struct i2c_driver inv_icm42607_driver = {
.driver = {
.name = "inv-icm42607-i2c",
.of_match_table = inv_icm42607_of_matches,
+ .pm = pm_ptr(&inv_icm42607_pm_ops),
},
.id_table = inv_icm42607_id,
.probe = inv_icm42607_probe,
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
index 0c8deb1f33e2..e361a692a32f 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
@@ -95,6 +95,7 @@ static struct spi_driver inv_icm42607_driver = {
.driver = {
.name = "inv-icm42607-spi",
.of_match_table = inv_icm42607_of_matches,
+ .pm = pm_ptr(&inv_icm42607_pm_ops),
},
.id_table = inv_icm42607_spi_id_table,
.probe = inv_icm42607_probe,
--
2.43.0
WARNING: multiple messages have this Message-ID (diff)
From: Chris Morgan <macroalpha82@gmail.com>
To: linux-iio@vger.kernel.org
Cc: andy@kernel.org, nuno.sa@analog.com, dlechner@baylibre.com,
jic23@kernel.org, jean-baptiste.maneyrol@tdk.com,
linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org,
heiko@sntech.de, conor+dt@kernel.org, krzk+dt@kernel.org,
robh@kernel.org, andriy.shevchenko@intel.com,
Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V12 5/9] iio: imu: inv_icm42607: Add PM support for icm42607
Date: Thu, 11 Jun 2026 15:26:02 -0500 [thread overview]
Message-ID: <20260611202607.85376-6-macroalpha82@gmail.com> (raw)
In-Reply-To: <20260611202607.85376-1-macroalpha82@gmail.com>
From: Chris Morgan <macromorgan@hotmail.com>
Add power management support for the ICM42607 device driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
drivers/iio/imu/inv_icm42607/inv_icm42607.h | 18 +++
.../iio/imu/inv_icm42607/inv_icm42607_core.c | 131 ++++++++++++++++++
.../iio/imu/inv_icm42607/inv_icm42607_i2c.c | 1 +
.../iio/imu/inv_icm42607/inv_icm42607_spi.c | 1 +
4 files changed, 151 insertions(+)
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607.h b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
index c85d3b74166f..28edc12d5373 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607.h
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
@@ -9,6 +9,7 @@
#include <linux/bits.h>
#include <linux/iio/iio.h>
#include <linux/mutex.h>
+#include <linux/pm.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/time.h>
@@ -105,11 +106,19 @@ struct inv_icm42607_hw {
u8 whoami;
};
+struct inv_icm42607_suspended {
+ enum inv_icm42607_sensor_mode gyro;
+ enum inv_icm42607_sensor_mode accel;
+ bool temp;
+};
+
/**
* struct inv_icm42607_state - driver state variables
* @hw: Hardware specific data.
* @map: regmap pointer.
* @vddio_supply: I/O voltage regulator for the chip.
+ * @suspended: suspended sensors configuration.
+ * @vddio_en: I/O voltage status for runtime PM.
* @lock: lock for serializing multiple registers access.
* @conf: chip sensors configurations.
* @orientation: sensor chip orientation relative to main hardware.
@@ -118,6 +127,8 @@ struct inv_icm42607_state {
const struct inv_icm42607_hw *hw;
struct regmap *map;
struct regulator *vddio_supply;
+ struct inv_icm42607_suspended suspended;
+ bool vddio_en;
struct mutex lock;
struct inv_icm42607_conf conf;
struct iio_mount_matrix orientation;
@@ -339,11 +350,18 @@ struct inv_icm42607_state {
#define INV_ICM42607_GYRO_STARTUP_TIME_MS 30
#define INV_ICM42607_TEMP_STARTUP_TIME_MS 77
+/*
+ * Suspend delay assumed from other icm42600 series device, not
+ * documented in datasheet.
+ */
+#define INV_ICM42607_SUSPEND_DELAY_MS (2 * USEC_PER_MSEC)
+
typedef int (*inv_icm42607_bus_setup)(struct inv_icm42607_state *);
extern const struct regmap_config inv_icm42607_regmap_config;
extern const struct inv_icm42607_hw inv_icm42607_hw_data;
extern const struct inv_icm42607_hw inv_icm42607p_hw_data;
+extern const struct dev_pm_ops inv_icm42607_pm_ops;
int inv_icm42607_core_probe(struct regmap *regmap,
const struct inv_icm42607_hw *hw,
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
index 5d40f1ee53d6..8073317088ec 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
@@ -11,6 +11,7 @@
#include <linux/iio/iio.h>
#include <linux/module.h>
#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/time.h>
@@ -102,6 +103,56 @@ const struct inv_icm42607_hw inv_icm42607p_hw_data = {
};
EXPORT_SYMBOL_NS_GPL(inv_icm42607p_hw_data, "IIO_ICM42607");
+static int inv_icm42607_set_pwr_mgmt0(struct inv_icm42607_state *st,
+ enum inv_icm42607_sensor_mode gyro,
+ enum inv_icm42607_sensor_mode accel,
+ bool temp, unsigned int *sleep_ms)
+{
+ enum inv_icm42607_sensor_mode oldaccel = st->conf.accel.mode;
+ enum inv_icm42607_sensor_mode oldgyro = st->conf.gyro.mode;
+ bool oldtemp = st->conf.temp_en;
+ unsigned int sleepval_ms;
+ unsigned int val;
+ int ret;
+
+ if (gyro == oldgyro && accel == oldaccel && temp == oldtemp)
+ return 0;
+
+ val = FIELD_PREP(INV_ICM42607_PWR_MGMT0_GYRO_MODE_MASK, gyro);
+ val |= FIELD_PREP(INV_ICM42607_PWR_MGMT0_ACCEL_MODE_MASK, accel);
+ /*
+ * Note that temp being enabled here doesn't affect PM since
+ * per 10.25 of the datasheet the clock will be off by default
+ * if both the gyro and accel modes are off.
+ */
+ if (!temp)
+ val |= INV_ICM42607_PWR_MGMT0_ACCEL_LP_CLK_SEL;
+ ret = regmap_write(st->map, INV_ICM42607_REG_PWR_MGMT0, val);
+ if (ret)
+ return ret;
+
+ st->conf.gyro.mode = gyro;
+ st->conf.accel.mode = accel;
+ st->conf.temp_en = temp;
+
+ sleepval_ms = 0;
+ if (temp && !oldtemp)
+ sleepval_ms = max(sleepval_ms, INV_ICM42607_TEMP_STARTUP_TIME_MS);
+
+ if (accel != oldaccel)
+ sleepval_ms = max(sleepval_ms, INV_ICM42607_ACCEL_STARTUP_TIME_MS);
+
+ if (gyro != oldgyro)
+ sleepval_ms = max(sleepval_ms, INV_ICM42607_GYRO_STARTUP_TIME_MS);
+
+ if (sleep_ms)
+ *sleep_ms = sleepval_ms;
+ else if (sleepval_ms)
+ fsleep(sleepval_ms * USEC_PER_MSEC);
+
+ return 0;
+}
+
static int inv_icm42607_set_conf(struct inv_icm42607_state *st,
const struct inv_icm42607_conf *conf)
{
@@ -213,12 +264,17 @@ static int inv_icm42607_enable_vddio_reg(struct inv_icm42607_state *st)
{
int ret;
+ if (st->vddio_en)
+ return 0;
+
ret = regulator_enable(st->vddio_supply);
if (ret)
return ret;
fsleep(INV_ICM42607_POWER_UP_TIME_US);
+ st->vddio_en = true;
+
return 0;
}
@@ -226,7 +282,12 @@ static void inv_icm42607_disable_vddio_reg(void *_data)
{
struct inv_icm42607_state *st = _data;
+ if (!st->vddio_en)
+ return;
+
regulator_disable(st->vddio_supply);
+
+ st->vddio_en = false;
}
int inv_icm42607_core_probe(struct regmap *regmap,
@@ -241,6 +302,8 @@ int inv_icm42607_core_probe(struct regmap *regmap,
if (!st)
return -ENOMEM;
+ dev_set_drvdata(dev, st);
+
ret = devm_mutex_init(dev, &st->lock);
if (ret)
return ret;
@@ -276,10 +339,78 @@ int inv_icm42607_core_probe(struct regmap *regmap,
if (ret)
return ret;
+ ret = devm_pm_runtime_set_active_enabled(dev);
+ if (ret)
+ return ret;
+
+ pm_runtime_set_autosuspend_delay(dev, INV_ICM42607_SUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(dev);
+
return 0;
}
EXPORT_SYMBOL_NS_GPL(inv_icm42607_core_probe, "IIO_ICM42607");
+static int inv_icm42607_suspend(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ return ret;
+
+ inv_icm42607_disable_vddio_reg(st);
+
+ return 0;
+}
+
+static int inv_icm42607_resume(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret;
+
+ ret = inv_icm42607_enable_vddio_reg(st);
+ if (ret)
+ return ret;
+
+ return pm_runtime_force_resume(dev);
+}
+
+static int inv_icm42607_runtime_suspend(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+
+ guard(mutex)(&st->lock);
+
+ /* save sensors state */
+ st->suspended.gyro = st->conf.gyro.mode;
+ st->suspended.accel = st->conf.accel.mode;
+ st->suspended.temp = st->conf.temp_en;
+
+ return inv_icm42607_set_pwr_mgmt0(st, INV_ICM42607_SENSOR_MODE_OFF,
+ INV_ICM42607_SENSOR_MODE_OFF, false,
+ NULL);
+}
+
+static int inv_icm42607_runtime_resume(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+
+ guard(mutex)(&st->lock);
+
+ /* restore sensors state */
+ return inv_icm42607_set_pwr_mgmt0(st, st->suspended.gyro,
+ st->suspended.accel,
+ st->suspended.temp, NULL);
+}
+
+EXPORT_NS_GPL_DEV_PM_OPS(inv_icm42607_pm_ops, IIO_ICM42607) = {
+ SYSTEM_SLEEP_PM_OPS(inv_icm42607_suspend, inv_icm42607_resume)
+ RUNTIME_PM_OPS(inv_icm42607_runtime_suspend,
+ inv_icm42607_runtime_resume,
+ NULL)
+};
+
MODULE_AUTHOR("InvenSense, Inc.");
MODULE_DESCRIPTION("InvenSense ICM-42607 device driver");
MODULE_LICENSE("GPL");
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
index a1484f32c5d9..6e7310db5598 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
@@ -85,6 +85,7 @@ static struct i2c_driver inv_icm42607_driver = {
.driver = {
.name = "inv-icm42607-i2c",
.of_match_table = inv_icm42607_of_matches,
+ .pm = pm_ptr(&inv_icm42607_pm_ops),
},
.id_table = inv_icm42607_id,
.probe = inv_icm42607_probe,
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
index 0c8deb1f33e2..e361a692a32f 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
@@ -95,6 +95,7 @@ static struct spi_driver inv_icm42607_driver = {
.driver = {
.name = "inv-icm42607-spi",
.of_match_table = inv_icm42607_of_matches,
+ .pm = pm_ptr(&inv_icm42607_pm_ops),
},
.id_table = inv_icm42607_spi_id_table,
.probe = inv_icm42607_probe,
--
2.43.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2026-06-11 20:28 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-06-11 20:25 [PATCH V12 0/9] Add Invensense ICM42607 Chris Morgan
2026-06-11 20:25 ` Chris Morgan
2026-06-11 20:25 ` [PATCH V12 1/9] dt-bindings: iio: imu: icm42600: Add mount-matrix to icm42600 Chris Morgan
2026-06-11 20:25 ` Chris Morgan
2026-06-11 20:25 ` [PATCH V12 2/9] dt-bindings: iio: imu: icm42600: Add icm42607 Chris Morgan
2026-06-11 20:25 ` Chris Morgan
2026-06-11 20:26 ` [PATCH V12 3/9] iio: imu: inv_icm42607: Add inv_icm42607 Core Driver Chris Morgan
2026-06-11 20:26 ` Chris Morgan
2026-06-11 20:39 ` sashiko-bot
2026-06-14 16:18 ` Jonathan Cameron
2026-06-14 16:18 ` Jonathan Cameron
2026-06-15 2:12 ` Chris Morgan
2026-06-15 2:12 ` Chris Morgan
2026-06-11 20:26 ` [PATCH V12 4/9] iio: imu: inv_icm42607: Add SPI For icm42607 Chris Morgan
2026-06-11 20:26 ` Chris Morgan
2026-06-11 20:41 ` sashiko-bot
2026-06-15 10:23 ` Andy Shevchenko
2026-06-15 10:23 ` Andy Shevchenko
2026-06-11 20:26 ` Chris Morgan [this message]
2026-06-11 20:26 ` [PATCH V12 5/9] iio: imu: inv_icm42607: Add PM support for icm42607 Chris Morgan
2026-06-11 20:46 ` sashiko-bot
2026-06-15 10:28 ` Andy Shevchenko
2026-06-15 10:28 ` Andy Shevchenko
2026-06-15 14:49 ` Chris Morgan
2026-06-15 14:49 ` Chris Morgan
2026-06-11 20:26 ` [PATCH V12 6/9] iio: imu: inv_icm42607: Add Temp Support in icm42607 Chris Morgan
2026-06-11 20:26 ` Chris Morgan
2026-06-11 20:46 ` sashiko-bot
2026-06-14 16:34 ` Jonathan Cameron
2026-06-14 16:34 ` Jonathan Cameron
2026-06-11 20:26 ` [PATCH V12 7/9] iio: imu: inv_icm42607: Add Accelerometer for icm42607 Chris Morgan
2026-06-11 20:26 ` Chris Morgan
2026-06-14 16:43 ` Jonathan Cameron
2026-06-14 16:43 ` Jonathan Cameron
2026-06-15 11:21 ` Andy Shevchenko
2026-06-15 11:21 ` Andy Shevchenko
2026-06-15 14:51 ` Chris Morgan
2026-06-15 14:51 ` Chris Morgan
2026-06-15 15:07 ` Andy Shevchenko
2026-06-15 15:07 ` Andy Shevchenko
2026-06-15 16:40 ` Chris Morgan
2026-06-15 16:40 ` Chris Morgan
2026-06-16 7:07 ` Andy Shevchenko
2026-06-16 7:07 ` Andy Shevchenko
2026-06-11 20:26 ` [PATCH V12 8/9] iio: imu: inv_icm42607: Add Gyroscope to icm42607 Chris Morgan
2026-06-11 20:26 ` Chris Morgan
2026-06-11 20:44 ` sashiko-bot
2026-06-11 20:26 ` [PATCH V12 9/9] arm64: dts: rockchip: Add icm42607p IMU for RG-DS Chris Morgan
2026-06-11 20:26 ` Chris Morgan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260611202607.85376-6-macroalpha82@gmail.com \
--to=macroalpha82@gmail.com \
--cc=andriy.shevchenko@intel.com \
--cc=andy@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=heiko@sntech.de \
--cc=jean-baptiste.maneyrol@tdk.com \
--cc=jic23@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=macromorgan@hotmail.com \
--cc=nuno.sa@analog.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.