* [PATCH v3] dt-bindings: misc: convert lis302.txt to YAML
2026-06-19 11:56 [PATCH 1/2] " Jad Keskes
@ 2026-06-19 12:24 ` Jad Keskes
2026-06-19 12:39 ` sashiko-bot
0 siblings, 1 reply; 3+ messages in thread
From: Jad Keskes @ 2026-06-19 12:24 UTC (permalink / raw)
To: Eric Piel, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: devicetree, linux-kernel, Jad Keskes
Replace the old lis302.txt with a YAML binding covering all four
compatibles (st,lis3lv02d, st,lis302dl-spi, st,lis331dlh,
st,lis33de) and their ~35 DT properties.
The old txt documented st,click-thresh-* and st,click-click-time-limit
but the code reads st,click-threshold-* and st,click-time-limit.
Keep the old names as deprecated so existing DTBs don't break.
Use a select block that matches only nodes with misc-driver
compatibles (including standalone st,lis3lv02d for omap3-n950-n9
and similar), paired with the IIO schema which handles the IIO
side. This avoids both schemas validating the same node.
Tested: dt_binding_check. dtbs_check against 7 omap/am335x DTBs
(am335x-evm, am335x-evmsk, am335x-pepper, am437x-sk-evm, omap3-n900,
omap3-n950, omap3-gta04a3) — no misc schema errors. Pre-existing
IIO schema errors on paired compatible nodes unchanged.
Signed-off-by: Jad Keskes <inasj268@gmail.com>
---
v3:
- Add st,lis3lv02d to select block (fixes Sashiko review #1)
- Drop Patch 2 entirely (fixes Sashiko review #2 — IIO SPI driver still matches st,lis302dl-spi)
- Single patch, no IIO schema changes
v2:
- Rebase onto Linux 7.1-rc6
- Drop IIO changes, this is a single patch now
.../devicetree/bindings/iio/accel/lis302.txt | 119 ------
.../bindings/misc/st,lis3lv02d.yaml | 400 ++++++++++++++++++
MAINTAINERS | 1 +
3 files changed, 401 insertions(+), 119 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/iio/accel/lis302.txt
create mode 100644 Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
diff --git a/Documentation/devicetree/bindings/iio/accel/lis302.txt b/Documentation/devicetree/bindings/iio/accel/lis302.txt
deleted file mode 100644
index 457539647f36..000000000000
--- a/Documentation/devicetree/bindings/iio/accel/lis302.txt
+++ /dev/null
@@ -1,119 +0,0 @@
-LIS302 accelerometer devicetree bindings
-
-This device is matched via its bus drivers, and has a number of properties
-that apply in on the generic device (independent from the bus).
-
-
-Required properties for the SPI bindings:
- - compatible: should be set to "st,lis3lv02d-spi"
- - reg: the chipselect index
- - spi-max-frequency: maximal bus speed, should be set to 1000000 unless
- constrained by external circuitry
- - interrupts: the interrupt generated by the device
-
-Required properties for the I2C bindings:
- - compatible: should be set to "st,lis3lv02d"
- - reg: i2c slave address
- - Vdd-supply: The input supply for Vdd
- - Vdd_IO-supply: The input supply for Vdd_IO
-
-
-Optional properties for all bus drivers:
-
- - st,click-single-{x,y,z}: if present, tells the device to issue an
- interrupt on single click events on the
- x/y/z axis.
- - st,click-double-{x,y,z}: if present, tells the device to issue an
- interrupt on double click events on the
- x/y/z axis.
- - st,click-thresh-{x,y,z}: set the x/y/z axis threshold
- - st,click-click-time-limit: click time limit, from 0 to 127.5msec
- with step of 0.5 msec
- - st,click-latency: click latency, from 0 to 255 msec with
- step of 1 msec.
- - st,click-window: click window, from 0 to 255 msec with
- step of 1 msec.
- - st,irq{1,2}-disable: disable IRQ 1/2
- - st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition
- - st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition
- - st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready condition
- - st,irq{1,2}-click: raise IRQ 1/2 on click condition
- - st,irq-open-drain: consider IRQ lines open-drain
- - st,irq-active-low: make IRQ lines active low
- - st,wu-duration-1: duration register for Free-Fall/Wake-Up
- interrupt 1
- - st,wu-duration-2: duration register for Free-Fall/Wake-Up
- interrupt 2
- - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
- upper/lower limit
- - st,wakeup-threshold: set wakeup threshold
- - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
- upper/lower limit for second wakeup
- engine.
- - st,wakeup2-threshold: set wakeup threshold for second wakeup
- engine.
- - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
- highpass cut-off frequency
- - st,hipass{1,2}-disable: disable highpass 1/2.
- - st,default-rate=: set the default rate
- - st,axis-{x,y,z}=: set the axis to map to the three coordinates.
- Negative values can be used for inverted axis.
- - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis
- (used by self-test)
-
-
-Example for a SPI device node:
-
- accelerometer@0 {
- compatible = "st,lis302dl-spi";
- reg = <0>;
- spi-max-frequency = <1000000>;
- interrupt-parent = <&gpio>;
- interrupts = <104 0>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- };
-
-Example for a I2C device node:
-
- lis331dlh: accelerometer@18 {
- compatible = "st,lis331dlh", "st,lis3lv02d";
- reg = <0x18>;
- Vdd-supply = <&lis3_reg>;
- Vdd_IO-supply = <&lis3_reg>;
-
- st,click-single-x;
- st,click-single-y;
- st,click-single-z;
- st,click-thresh-x = <10>;
- st,click-thresh-y = <10>;
- st,click-thresh-z = <10>;
- st,irq1-click;
- st,irq2-click;
- st,wakeup-x-lo;
- st,wakeup-x-hi;
- st,wakeup-y-lo;
- st,wakeup-y-hi;
- st,wakeup-z-lo;
- st,wakeup-z-hi;
- st,min-limit-x = <120>;
- st,min-limit-y = <120>;
- st,min-limit-z = <140>;
- st,max-limit-x = <550>;
- st,max-limit-y = <550>;
- st,max-limit-z = <750>;
- };
-
diff --git a/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
new file mode 100644
index 000000000000..c73371b754a1
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
@@ -0,0 +1,400 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/st,lis3lv02d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics LIS3LV02D and similar accelerometers (misc driver)
+
+maintainers:
+ - Eric Piel <eric.piel@tremplin-utc.net>
+
+description:
+ This binding describes the STMicroelectronics accelerometers supported by
+ the misc/lis3lv02d driver. This driver provides input (joystick) and
+ hardware monitoring support, in contrast to the IIO st-accel driver which
+ also supports some of these devices.
+ Refer to Documentation/devicetree/bindings/iio/st,st-sensors.yaml for the
+ IIO binding.
+
+select:
+ anyOf:
+ - properties:
+ compatible:
+ contains:
+ const: st,lis302dl-spi
+ - properties:
+ compatible:
+ contains:
+ const: st,lis331dlh
+ - properties:
+ compatible:
+ contains:
+ const: st,lis33de
+ - properties:
+ compatible:
+ contains:
+ const: st,lis3lv02d
+ required:
+ - compatible
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - st,lis331dlh
+ - st,lis33de
+ - const: st,lis3lv02d
+ - const: st,lis331dlh
+ - const: st,lis3lv02d
+ - const: st,lis302dl-spi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 2
+
+ spi-max-frequency:
+ description: SPI bus frequency; should be set to 1000000 unless
+ constrained by external circuitry.
+ maximum: 1000000
+
+ Vdd-supply:
+ description: The input supply for Vdd.
+
+ Vdd_IO-supply:
+ description: The input supply for Vdd_IO.
+
+ st,click-single-x:
+ description: Issue an interrupt on single click events on the X axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-double-x:
+ description: Issue an interrupt on double click events on the X axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-single-y:
+ description: Issue an interrupt on single click events on the Y axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-double-y:
+ description: Issue an interrupt on double click events on the Y axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-single-z:
+ description: Issue an interrupt on single click events on the Z axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-double-z:
+ description: Issue an interrupt on double click events on the Z axis.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,click-thresh-x:
+ description: X axis click threshold (deprecated spelling, use st,click-threshold-x).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+
+ st,click-thresh-y:
+ description: Y axis click threshold (deprecated spelling, use st,click-threshold-y).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+
+ st,click-thresh-z:
+ description: Z axis click threshold (deprecated spelling, use st,click-threshold-z).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+
+ st,click-threshold-x:
+ description: X axis click threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,click-threshold-y:
+ description: Y axis click threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,click-threshold-z:
+ description: Z axis click threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,click-click-time-limit:
+ description: Click time limit (deprecated spelling, use st,click-time-limit).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+ deprecated: true
+
+ st,click-time-limit:
+ description: Click time limit, from 0 to 127.5 msec with step of 0.5 msec.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,click-latency:
+ description: Click latency, from 0 to 255 msec with step of 1 msec.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,click-window:
+ description: Click window, from 0 to 255 msec with step of 1 msec.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,irq1-disable:
+ description: Disable IRQ 1.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-ff-wu-1:
+ description: Raise IRQ 1 on FF_WU_1 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-ff-wu-2:
+ description: Raise IRQ 1 on FF_WU_2 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-data-ready:
+ description: Raise IRQ 1 on data ready condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq1-click:
+ description: Raise IRQ 1 on click condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-disable:
+ description: Disable IRQ 2.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-ff-wu-1:
+ description: Raise IRQ 2 on FF_WU_1 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-ff-wu-2:
+ description: Raise IRQ 2 on FF_WU_2 condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-data-ready:
+ description: Raise IRQ 2 on data ready condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq2-click:
+ description: Raise IRQ 2 on click condition.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq-open-drain:
+ description: Consider IRQ lines open-drain.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,irq-active-low:
+ description: Make IRQ lines active low.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wu-duration-1:
+ description: Duration register for Free-Fall/Wake-Up interrupt 1.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,wu-duration-2:
+ description: Duration register for Free-Fall/Wake-Up interrupt 2.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,wakeup-x-lo:
+ description: Set wakeup condition on X axis for lower limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-x-hi:
+ description: Set wakeup condition on X axis for upper limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-y-lo:
+ description: Set wakeup condition on Y axis for lower limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-y-hi:
+ description: Set wakeup condition on Y axis for upper limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-z-lo:
+ description: Set wakeup condition on Z axis for lower limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-z-hi:
+ description: Set wakeup condition on Z axis for upper limit.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup-threshold:
+ description: Set wakeup threshold.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,wakeup2-x-lo:
+ description: Set wakeup condition on X axis for lower limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-x-hi:
+ description: Set wakeup condition on X axis for upper limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-y-lo:
+ description: Set wakeup condition on Y axis for lower limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-y-hi:
+ description: Set wakeup condition on Y axis for upper limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-z-lo:
+ description: Set wakeup condition on Z axis for lower limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-z-hi:
+ description: Set wakeup condition on Z axis for upper limit for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,wakeup2-threshold:
+ description: Set wakeup threshold for second wakeup engine.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+
+ st,highpass-cutoff-hz:
+ description: Highpass cut-off frequency. Valid values are 1, 2, 4 or 8.
+ enum: [1, 2, 4, 8]
+
+ st,hipass1-disable:
+ description: Disable highpass filter 1.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,hipass2-disable:
+ description: Disable highpass filter 2.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,default-rate:
+ description: Set the default output data rate.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ st,axis-x:
+ description: Set the X axis mapping. Negative values can be used for inverted axis.
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,axis-y:
+ description: Set the Y axis mapping. Negative values can be used for inverted axis.
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,axis-z:
+ description: Set the Z axis mapping. Negative values can be used for inverted axis.
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,min-limit-x:
+ description: Minimum limit for X axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,min-limit-y:
+ description: Minimum limit for Y axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,min-limit-z:
+ description: Minimum limit for Z axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,max-limit-x:
+ description: Maximum limit for X axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,max-limit-y:
+ description: Maximum limit for Y axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+ st,max-limit-z:
+ description: Maximum limit for Z axis (used by self-test).
+ $ref: /schemas/types.yaml#/definitions/int32
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ not:
+ contains:
+ const: st,lis302dl-spi
+ then:
+ required:
+ - Vdd-supply
+ - Vdd_IO-supply
+ else:
+ properties:
+ Vdd-supply: false
+ Vdd_IO-supply: false
+ required:
+ - spi-max-frequency
+ - interrupts
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ accelerometer@18 {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x18>;
+ Vdd-supply = <&lis3_reg>;
+ Vdd_IO-supply = <&lis3_reg>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <18 0>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-threshold-x = <10>;
+ st,click-threshold-y = <10>;
+ st,click-threshold-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ st,min-limit-x = <120>;
+ st,min-limit-y = <120>;
+ st,min-limit-z = <140>;
+ st,max-limit-x = <550>;
+ st,max-limit-y = <550>;
+ st,max-limit-z = <750>;
+ };
+ };
+ - |
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ accelerometer@0 {
+ compatible = "st,lis302dl-spi";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ interrupt-parent = <&gpio>;
+ interrupts = <104 0>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-threshold-x = <10>;
+ st,click-threshold-y = <10>;
+ st,click-threshold-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ };
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 9ec290e38b44..4cffabbabf0e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14858,6 +14858,7 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/
LIS3LV02D ACCELEROMETER DRIVER
M: Eric Piel <eric.piel@tremplin-utc.net>
S: Maintained
+F: Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
F: Documentation/misc-devices/lis3lv02d.rst
F: drivers/misc/lis3lv02d/
F: drivers/platform/x86/hp/hp_accel.c
--
2.54.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3] dt-bindings: misc: convert lis302.txt to YAML
2026-06-19 12:24 ` [PATCH v3] " Jad Keskes
@ 2026-06-19 12:39 ` sashiko-bot
0 siblings, 0 replies; 3+ messages in thread
From: sashiko-bot @ 2026-06-19 12:39 UTC (permalink / raw)
To: Jad Keskes; +Cc: robh, conor+dt, devicetree
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] Redundant 'select' block fails its stated purpose in the commit message
--
commit 7b1f6ec4590fb8fea27ae6accf9a20a8de12ccd1
Author: Jad Keskes <inasj268@gmail.com>
dt-bindings: misc: convert lis302.txt to YAML
Replace the old lis302.txt with a YAML binding covering four compatibles.
The commit message states it includes a select block to avoid validating
nodes against both the misc and IIO schemas.
> Use a select block that matches only nodes with misc-driver
> compatibles (including standalone st,lis3lv02d for omap3-n950-n9
> and similar), paired with the IIO schema which handles the IIO
> side. This avoids both schemas validating the same node.
[Severity: Medium]
Does this select block actually prevent the IIO schema from validating
the node?
In the dt-schema architecture, schemas evaluate independently. A select
block in this misc schema only determines if this specific schema applies;
it has no effect on whether the IIO schema also matches the compatible
string.
The testing note mentioning "Pre-existing IIO schema errors on paired
compatible nodes unchanged" seems to confirm both schemas are still
validating the node.
> diff --git a/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
> new file mode 100644
> index 0000000000000..c73371b754a1e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/st,lis3lv02d.yaml
[ ... ]
> +select:
> + anyOf:
> + - properties:
> + compatible:
> + contains:
> + const: st,lis302dl-spi
> + - properties:
> + compatible:
> + contains:
> + const: st,lis331dlh
> + - properties:
> + compatible:
> + contains:
> + const: st,lis33de
> + - properties:
> + compatible:
> + contains:
> + const: st,lis3lv02d
> + required:
> + - compatible
[Severity: Medium]
Is this explicit select block necessary?
Since this block exactly mirrors the default select block automatically
generated by dt-schema from the compatible property definition below it,
could this be removed entirely to simplify the binding?
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260619122446.867091-1-inasj268@gmail.com?part=1
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v3] dt-bindings: misc: convert lis302.txt to YAML
@ 2026-06-23 23:52 kernel test robot
0 siblings, 0 replies; 3+ messages in thread
From: kernel test robot @ 2026-06-23 23:52 UTC (permalink / raw)
To: oe-kbuild; +Cc: lkp
::::::
:::::: Manual check reason: "dtcheck: binding changes may go via different trees"
::::::
BCC: lkp@intel.com
CC: oe-kbuild-all@lists.linux.dev
In-Reply-To: <20260619122446.867091-1-inasj268@gmail.com>
References: <20260619122446.867091-1-inasj268@gmail.com>
TO: Jad Keskes <inasj268@gmail.com>
TO: Eric Piel <eric.piel@tremplin-utc.net>
TO: Rob Herring <robh@kernel.org>
TO: Krzysztof Kozlowski <krzk@kernel.org>
TO: Conor Dooley <conor+dt@kernel.org>
CC: devicetree@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: Jad Keskes <inasj268@gmail.com>
Hi Jad,
kernel test robot noticed the following build warnings:
[auto build test WARNING on robh/for-next]
[also build test WARNING on linus/master v7.1 next-20260623]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Jad-Keskes/dt-bindings-misc-convert-lis302-txt-to-YAML/20260622-134640
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
patch link: https://lore.kernel.org/r/20260619122446.867091-1-inasj268%40gmail.com
patch subject: [PATCH v3] dt-bindings: misc: convert lis302.txt to YAML
:::::: branch date: 2 days ago
:::::: commit date: 2 days ago
config: arm-randconfig-2051-20260622 (https://download.01.org/0day-ci/archive/20260624/202606240120.r4ppKtqB-lkp@intel.com/config)
compiler: arm-linux-gnueabi-gcc (GCC) 8.5.0
dtschema: 2026.7.dev1+g2203c1720
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20260624/202606240120.r4ppKtqB-lkp@intel.com/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/r/202606240120.r4ppKtqB-lkp@intel.com/
dtcheck warnings: (new ones prefixed by >>)
'st,lis331dlh' is not one of ['st,h3lis331dl-accel', 'st,lis2de12', 'st,lis2dw12', 'st,lis2hh12', 'st,lis2dh12-accel', 'st,lis2ds12', 'st,lis302dl', 'st,lis331dl-accel', 'st,lis331dlh-accel', 'st,lis3de', 'st,lis3dh-accel', 'st,lis3dhh', 'st,lis3l02dq', 'st,lis3lv02dl-accel', 'st,lng2dm-accel', 'st,lsm303agr-accel', 'st,lsm303c-accel', 'st,lsm303dl-accel', 'st,lsm303dlh-accel', 'st,lsm303dlhc-accel', 'st,lsm303dlm-accel', 'st,lsm330-accel', 'st,lsm330d-accel', 'st,lsm330dl-accel', 'st,lsm330dlc-accel']
'st,iis328dq' was expected
'st,lis331dlh' is not one of ['silan,sc7a20']
'st,lis331dlh' is not one of ['st,l3g4200d-gyro', 'st,l3g4is-gyro', 'st,l3gd20-gyro', 'st,l3gd20h-gyro', 'st,lsm330-gyro', 'st,lsm330d-gyro', 'st,lsm330dl-gyro', 'st,lsm330dlc-gyro', 'st,lsm9ds0-gyro']
'st,lis331dlh' is not one of ['st,iis2mdc', 'st,lis2mdl', 'st,lis3mdl-magn', 'st,lsm303agr-magn', 'st,lsm303c-magn', 'st,lsm303dlh-magn', 'st,lsm303dlhc-magn', 'st,lsm303dlm-magn', 'st,lsm9ds1-magn']
'st,lis331dlh' is not one of ['st,lps001wp-press', 'st,lps22df', 'st,lps22hb-press', 'st,lps22hh', 'st,lps25h-press', 'st,lps331ap-press', 'st,lps33hw', 'st,lps35hw']
'st,lis331dlh' is not one of ['st,lsm303d-imu', 'st,lsm9ds0-imu']
'st,lis331dlh' is not one of ['st,lis302dl-spi', 'st,lis3lv02d']
'st,h3lis331dl-accel' was expected
from schema $id: http://devicetree.org/schemas/iio/st,st-sensors.yaml
>> arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dtb: accelerometer@1d (st,lis331dlh): 'Vdd-supply' is a required property
from schema $id: http://devicetree.org/schemas/misc/st,lis3lv02d.yaml
>> arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dtb: accelerometer@1d (st,lis331dlh): 'Vdd_IO-supply' is a required property
from schema $id: http://devicetree.org/schemas/misc/st,lis3lv02d.yaml
arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dtb: gpio-keys (gpio-keys): 'lid', 'tablet_mode' do not match any of the regexes: '^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml
arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dtb: /i2c/camera@21: failed to match any schema with compatible: ['ovti,ov7670']
--
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2026-06-23 23:53 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-06-23 23:52 [PATCH v3] dt-bindings: misc: convert lis302.txt to YAML kernel test robot
-- strict thread matches above, loose matches on Subject: below --
2026-06-19 11:56 [PATCH 1/2] " Jad Keskes
2026-06-19 12:24 ` [PATCH v3] " Jad Keskes
2026-06-19 12:39 ` sashiko-bot
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.