[PATCH v2 0/3] Add devicetree for the Graperain G3568 v2

[PATCH v2 0/3] Add devicetree for the Graperain G3568 v2

[Coia Prant]

Changes in v2:
- Fix trailing whitespaces and other formatting issues.

Notes/Unchanged from v1:
- ADC keys have been verified with evtest and works fine; kept unchanged.
- The 'regulator-off-in-suspend' property for vqmmc-supply is retained.
  This is a known issue shared by most similar boards and should be
   addressed globally later.

Planned future changes (to be both with the similar X3568 v4 board series):
- Replace the legacy 'gpio' label with 'gpios'.
- Add the Bluetooth UART child node.

Coia Prant (3):
  dt-bindings: vendor-prefixes: Add graperain
  dt-bindings: arm: rockchip: Add Graperain G3568 series
  arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

 .../devicetree/bindings/arm/rockchip.yaml     |   6 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../rockchip/rk3568-graperain-g3568-v2.dts    | 894 ++++++++++++++++++
 4 files changed, 903 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts

-- 
2.47.3


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH v2 0/3] Add devicetree for the Graperain G3568 v2

[Coia Prant]

Changes in v2:
- Fix trailing whitespaces and other formatting issues.

Notes/Unchanged from v1:
- ADC keys have been verified with evtest and works fine; kept unchanged.
- The 'regulator-off-in-suspend' property for vqmmc-supply is retained.
  This is a known issue shared by most similar boards and should be
   addressed globally later.

Planned future changes (to be both with the similar X3568 v4 board series):
- Replace the legacy 'gpio' label with 'gpios'.
- Add the Bluetooth UART child node.

Coia Prant (3):
  dt-bindings: vendor-prefixes: Add graperain
  dt-bindings: arm: rockchip: Add Graperain G3568 series
  arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

 .../devicetree/bindings/arm/rockchip.yaml     |   6 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../rockchip/rk3568-graperain-g3568-v2.dts    | 894 ++++++++++++++++++
 4 files changed, 903 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts

-- 
2.47.3

[PATCH v2 1/3] dt-bindings: vendor-prefixes: Add graperain

[Coia Prant]

Add graperain to the vendor prefixes.

Link: https://www.graperain.cn/ (China)
Link: https://www.graperain.com/ (Global)

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 396044f368e7c..641a37c0debc9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -682,6 +682,8 @@ patternProperties:
     description: Goramo Gorecki
   "^gplus,.*":
     description: GPLUS
+  "^graperain,.*":
+    description: Shenzhen Graperain Technology Co., Ltd.
   "^grinn,.*":
     description: Grinn
   "^grmn,.*":
-- 
2.47.3


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH v2 1/3] dt-bindings: vendor-prefixes: Add graperain

[Coia Prant]

Add graperain to the vendor prefixes.

Link: https://www.graperain.cn/ (China)
Link: https://www.graperain.com/ (Global)

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 396044f368e7c..641a37c0debc9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -682,6 +682,8 @@ patternProperties:
     description: Goramo Gorecki
   "^gplus,.*":
     description: GPLUS
+  "^graperain,.*":
+    description: Shenzhen Graperain Technology Co., Ltd.
   "^grinn,.*":
     description: Grinn
   "^grmn,.*":
-- 
2.47.3

Re: [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add graperain

[Krzysztof Kozlowski]

On Tue, Jun 30, 2026 at 11:38:09PM +0800, Coia Prant wrote:
> Add graperain to the vendor prefixes.
> 
> Link: https://www.graperain.cn/ (China)
> Link: https://www.graperain.com/ (Global)
> 
> Signed-off-by: Coia Prant <coiaprant@gmail.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
>

<form letter>
This is a friendly reminder during the review process.

It looks like you received a tag and forgot to add it.

If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions of patchset, under or above your Signed-off-by tag, unless
patch changed significantly (e.g. new properties added to the DT
bindings). Tag is "received", when provided in a message replied to you
on the mailing list. Tools like b4 can help here. However, there's no
need to repost patches *only* to add the tags. The upstream maintainer
will do that for tags received on the version they apply.

Please read:
https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577

If a tag was not added on purpose, please state in the patch changelog
or cover letter why and what changed.
</form letter>

Best regards,
Krzysztof


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add graperain

[Krzysztof Kozlowski]

On Tue, Jun 30, 2026 at 11:38:09PM +0800, Coia Prant wrote:
> Add graperain to the vendor prefixes.
> 
> Link: https://www.graperain.cn/ (China)
> Link: https://www.graperain.com/ (Global)
> 
> Signed-off-by: Coia Prant <coiaprant@gmail.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
>

<form letter>
This is a friendly reminder during the review process.

It looks like you received a tag and forgot to add it.

If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions of patchset, under or above your Signed-off-by tag, unless
patch changed significantly (e.g. new properties added to the DT
bindings). Tag is "received", when provided in a message replied to you
on the mailing list. Tools like b4 can help here. However, there's no
need to repost patches *only* to add the tags. The upstream maintainer
will do that for tags received on the version they apply.

Please read:
https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577

If a tag was not added on purpose, please state in the patch changelog
or cover letter why and what changed.
</form letter>

Best regards,
Krzysztof

[PATCH v2 2/3] dt-bindings: arm: rockchip: Add Graperain G3568 series

[Coia Prant]

Document Graperain G3568 v2
 which is a development board based on RK3568 SoC.

This series also have an SBC series with the suffix "box".

This board is development board series, not SBC series.

Link: https://www.graperain.cn/RK3568/RK3568-Development/ (China)
Link: https://www.graperain.com/ARM-Embedded-RK3568-Development-Board/ (Global)
Link: https://image.chukouplus.com/upload/C_153/product_file/20211022/6daddec9e400458816dd4c57ba807fc3.pdf

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 1a9dde18626d0..9eb2f66ba3856 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -684,6 +684,12 @@ properties:
           - const: google,veyron
           - const: rockchip,rk3288
 
+      - description: Graperain G3568 series board
+        items:
+          - enum:
+              - graperain,g3568-v2
+          - const: rockchip,rk3568
+
       - description: H96 Max V58 TV Box
         items:
           - const: haochuangyi,h96-max-v58
-- 
2.47.3


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH v2 2/3] dt-bindings: arm: rockchip: Add Graperain G3568 series

[Coia Prant]

Document Graperain G3568 v2
 which is a development board based on RK3568 SoC.

This series also have an SBC series with the suffix "box".

This board is development board series, not SBC series.

Link: https://www.graperain.cn/RK3568/RK3568-Development/ (China)
Link: https://www.graperain.com/ARM-Embedded-RK3568-Development-Board/ (Global)
Link: https://image.chukouplus.com/upload/C_153/product_file/20211022/6daddec9e400458816dd4c57ba807fc3.pdf

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 1a9dde18626d0..9eb2f66ba3856 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -684,6 +684,12 @@ properties:
           - const: google,veyron
           - const: rockchip,rk3288
 
+      - description: Graperain G3568 series board
+        items:
+          - enum:
+              - graperain,g3568-v2
+          - const: rockchip,rk3568
+
       - description: H96 Max V58 TV Box
         items:
           - const: haochuangyi,h96-max-v58
-- 
2.47.3

Re: [PATCH v2 2/3] dt-bindings: arm: rockchip: Add Graperain G3568 series

[Krzysztof Kozlowski]

On Tue, Jun 30, 2026 at 11:38:11PM +0800, Coia Prant wrote:
> Document Graperain G3568 v2
>  which is a development board based on RK3568 SoC.

Broken wrapping.

Best regards,
Krzysztof


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH v2 2/3] dt-bindings: arm: rockchip: Add Graperain G3568 series

[Krzysztof Kozlowski]

On Tue, Jun 30, 2026 at 11:38:11PM +0800, Coia Prant wrote:
> Document Graperain G3568 v2
>  which is a development board based on RK3568 SoC.

Broken wrapping.

Best regards,
Krzysztof

Re: [PATCH v2 2/3] dt-bindings: arm: rockchip: Add Graperain G3568 series

[Coia Prant]

On July 1, 2026 3:07:03 PM GMT+08:00, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>On Tue, Jun 30, 2026 at 11:38:11PM +0800, Coia Prant wrote:
>> Document Graperain G3568 v2
>>  which is a development board based on RK3568 SoC.
>
>Broken wrapping.
>
>Best regards,
>Krzysztof
>

Acknowledged. I will fix the text wrapping and clean up the commit 
message in the v3 submission.

Thanks for pointing it out!

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH v2 2/3] dt-bindings: arm: rockchip: Add Graperain G3568 series

[Coia Prant]

On July 1, 2026 3:07:03 PM GMT+08:00, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>On Tue, Jun 30, 2026 at 11:38:11PM +0800, Coia Prant wrote:
>> Document Graperain G3568 v2
>>  which is a development board based on RK3568 SoC.
>
>Broken wrapping.
>
>Best regards,
>Krzysztof
>

Acknowledged. I will fix the text wrapping and clean up the commit 
message in the v3 submission.

Thanks for pointing it out!

[PATCH v2 3/3] arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

[Coia Prant]

The Graperain G3568 v2 is an RK3568-based development board, just like
 the RK3568-EVB.
It always uses soldered connections between the GR3568CV2 core board and
 the RK3568BV2/GR3568BV2 I/O board.

The G3568 board has multiple hardware revisions, and we currently
 support v2 (I/O board).

Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x RTL8211F RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac dual-band
- LED:
  Power: AlwaysOn
  User: GPIO
- Button:
  ESC: SARADC/0 <1100k µV>
  MENU: SARADC/0 <1400k µV>
  VOL-: SARADC/0 <430k µV>
  VOL+: SARADC/0 <50k µV>
  Power/Reset: PMIC RK809
- CAN
  CAN/1: 4-pin (PH 2.0)
- PWM
  PWM/4: Backlight
  PWM/5: Backlight
  PWM/7: IR Receiver
- UART:
  UART/2: Debug TTL - 1500000 8N1 (1.25mm)
  UART/3: TTL (PH 2.0)
  UART/4: TTL (PH 2.0)
  UART/8: AP6356S Bluetooth
  UART/9: TTL (PH 2.0)
- I2C:
  I2C/0: PMIC RK809
  I2C/1: Touchscreen
  I2C/4: Camera
  I2C/5: RTC@51 PCF8563
- I2S:
  I2S/0: HDMI Sound
  I2S/1: RK809 Audio Codec
  I2S/3: AP6356S Bluetooth Sound
- SDMMC:
  SDMMC/0: microSD (TF) slot
  SDMMC/2: AP6356S SDIO WiFi card
- Camera: 1x CSI
- Video: HDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: HDMI / MIC / Speaker / SPDIF / 3.5mm Headphones / AP6356S Bluetooth
- USB:
  USB 2.0 HOST x2
  USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST)
  USB 3.0 HOST x1
  USB 3.0 OTG/HOST x1
- SATA: 1x SATA 3.0 with Power/4-pin
- PCIe: 1x PCIe 3.0 x2 (x4 connecter)

Link:
- https://image.chukouplus.com/upload/C_153/product_file/20211022/6daddec9e400458816dd4c57ba807fc3.pdf
- https://blog.gov.cooking/archives/research-graperain-g3568-v2-and-flash.html

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../rockchip/rk3568-graperain-g3568-v2.dts    | 894 ++++++++++++++++++
 2 files changed, 895 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 761d82b4f4f2a..6e9d049e8ddaf 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -144,6 +144,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-easepi-r1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-fastrhino-r66s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-fastrhino-r68s.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-graperain-g3568-v2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-hinlink-h66k.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-hinlink-h68k.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-lubancat-2.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts b/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts
new file mode 100644
index 0000000000000..221992d6c6003
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts
@@ -0,0 +1,894 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+	model = "Graperain G3568 v2";
+	compatible = "graperain,g3568-v2", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc0;
+		mmc2 = &sdmmc2;
+		rtc0 = &rtc0;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-esc {
+			label = "esc";
+			linux,code = <KEY_ESC>;
+			press-threshold-microvolt = <1250000>;
+		};
+
+		button-menu {
+			label = "menu";
+			linux,code = <KEY_MENU>;
+			press-threshold-microvolt = <1600000>;
+		};
+
+		button-vol-down {
+			label = "volume down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			press-threshold-microvolt = <600000>;
+		};
+
+		button-vol-up {
+			label = "volume up";
+			linux,code = <KEY_VOLUMEUP>;
+			press-threshold-microvolt = <100000>;
+		};
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_work: led-0 {
+			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_work_en>;
+		};
+	};
+
+	rk809-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	pdm_codec: pdm-codec {
+		compatible = "dmic-codec";
+		num-channels = <2>;
+		#sound-dai-cells = <0>;
+	};
+
+	pdm_sound: pdm-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "microphone";
+
+		simple-audio-card,cpu {
+			sound-dai = <&pdm>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&pdm_codec>;
+		};
+	};
+
+	spdif_dit: spdif-dit {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_sound: spdif-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&spdif_dit>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <300>;
+		reset-gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
+	};
+
+	dc_12v: regulator-dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	pcie30_avdd0v9: regulator-pcie30-avdd0v9 {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: regulator-pcie30-avdd1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcc3v3_sys: regulator-vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc3v3_pcie: regulator-vcc3v3-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc3v3_pcie_en_pin>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <5000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb: regulator-vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb_host: regulator-vcc5v0-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: regulator-vcc5v0-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+};
+
+&can1 {
+	assigned-clocks = <&cru CLK_CAN1>;
+	assigned-clock-rates = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1m1_pins>;
+	status = "okay";
+};
+
+/* used for usb_host0_xhci */
+&combphy0 {
+	status = "okay";
+};
+
+/* used for usb_host1_xhci */
+&combphy1 {
+	status = "okay";
+};
+
+/* connected to sata2 */
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac0 {
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_tx_bus2
+		     &gmac0_rx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus>;
+	phy-handle = <&rgmii_phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+		system-power-controller;
+		#sound-dai-cells = <0>;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+
+		codec {
+			rockchip,mic-in-differential;
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	rtc0: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+	};
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_lrcktx &i2s1m0_sdi0 &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+/* used for AP6356S Bluetooth Sound */
+&i2s3_2ch {
+	status = "okay";
+};
+
+&mdio0 {
+	rgmii_phy0: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
+&pcie30phy {
+	status = "okay";
+};
+
+&pcie3x2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_pin>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pdm {
+	status = "okay";
+};
+
+&pinctrl {
+	leds {
+		led_work_en: led_work_en {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable: wifi-enable {
+			rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_reset_pin: pcie-reset-pin {
+			rockchip,pins = <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc3v3_pcie_en_pin: vcc3v3-pcie-en-pin {
+			rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&pwm5 {
+	status = "okay";
+};
+
+/* Required remotectl for IR receiver */
+&pwm7 {
+	status = "disabled";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sata2 {
+	status = "okay";
+};
+
+/* used for eMMC */
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	status = "okay";
+};
+
+/* used for microSD (TF) Slot */
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+/* used for AP6356S WiFi */
+&sdmmc2 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+/* used for Debug */
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-0 = <&uart3m1_xfer>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-0 = <&uart4m1_xfer>;
+	status = "okay";
+};
+
+/* used for WiFi/BT AP6356S */
+&uart8 {
+	pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn>;
+	status = "okay";
+};
+
+&uart9 {
+	pinctrl-0 = <&uart9m1_xfer>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
-- 
2.47.3


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH v2 3/3] arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

[Coia Prant]

The Graperain G3568 v2 is an RK3568-based development board, just like
 the RK3568-EVB.
It always uses soldered connections between the GR3568CV2 core board and
 the RK3568BV2/GR3568BV2 I/O board.

The G3568 board has multiple hardware revisions, and we currently
 support v2 (I/O board).

Specification:
- SoC: RockChip RK3568 ARM64 (4 cores)
- eMMC: 16-128 GB
- RAM: 2-16 GB
- Power: DC 12V 2A
- Ethernet: 2x RTL8211F RGMII (10/100/1000 Mbps)
- Wireless radio: 802.11b/g/n/ac dual-band
- LED:
  Power: AlwaysOn
  User: GPIO
- Button:
  ESC: SARADC/0 <1100k µV>
  MENU: SARADC/0 <1400k µV>
  VOL-: SARADC/0 <430k µV>
  VOL+: SARADC/0 <50k µV>
  Power/Reset: PMIC RK809
- CAN
  CAN/1: 4-pin (PH 2.0)
- PWM
  PWM/4: Backlight
  PWM/5: Backlight
  PWM/7: IR Receiver
- UART:
  UART/2: Debug TTL - 1500000 8N1 (1.25mm)
  UART/3: TTL (PH 2.0)
  UART/4: TTL (PH 2.0)
  UART/8: AP6356S Bluetooth
  UART/9: TTL (PH 2.0)
- I2C:
  I2C/0: PMIC RK809
  I2C/1: Touchscreen
  I2C/4: Camera
  I2C/5: RTC@51 PCF8563
- I2S:
  I2S/0: HDMI Sound
  I2S/1: RK809 Audio Codec
  I2S/3: AP6356S Bluetooth Sound
- SDMMC:
  SDMMC/0: microSD (TF) slot
  SDMMC/2: AP6356S SDIO WiFi card
- Camera: 1x CSI
- Video: HDMI / DSI0 (MIPI/LVDS) / DSI1 (MIPI/EDP)
- Audio: HDMI / MIC / Speaker / SPDIF / 3.5mm Headphones / AP6356S Bluetooth
- USB:
  USB 2.0 HOST x2
  USB 2.0 OTG x1 (shared with USB 3.0 OTG/HOST)
  USB 3.0 HOST x1
  USB 3.0 OTG/HOST x1
- SATA: 1x SATA 3.0 with Power/4-pin
- PCIe: 1x PCIe 3.0 x2 (x4 connecter)

Link:
- https://image.chukouplus.com/upload/C_153/product_file/20211022/6daddec9e400458816dd4c57ba807fc3.pdf
- https://blog.gov.cooking/archives/research-graperain-g3568-v2-and-flash.html

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../rockchip/rk3568-graperain-g3568-v2.dts    | 894 ++++++++++++++++++
 2 files changed, 895 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 761d82b4f4f2a..6e9d049e8ddaf 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -144,6 +144,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-easepi-r1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-fastrhino-r66s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-fastrhino-r68s.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-graperain-g3568-v2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-hinlink-h66k.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-hinlink-h68k.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-lubancat-2.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts b/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts
new file mode 100644
index 0000000000000..221992d6c6003
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts
@@ -0,0 +1,894 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+	model = "Graperain G3568 v2";
+	compatible = "graperain,g3568-v2", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc0;
+		mmc2 = &sdmmc2;
+		rtc0 = &rtc0;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-esc {
+			label = "esc";
+			linux,code = <KEY_ESC>;
+			press-threshold-microvolt = <1250000>;
+		};
+
+		button-menu {
+			label = "menu";
+			linux,code = <KEY_MENU>;
+			press-threshold-microvolt = <1600000>;
+		};
+
+		button-vol-down {
+			label = "volume down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			press-threshold-microvolt = <600000>;
+		};
+
+		button-vol-up {
+			label = "volume up";
+			linux,code = <KEY_VOLUMEUP>;
+			press-threshold-microvolt = <100000>;
+		};
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_work: led-0 {
+			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_work_en>;
+		};
+	};
+
+	rk809-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	pdm_codec: pdm-codec {
+		compatible = "dmic-codec";
+		num-channels = <2>;
+		#sound-dai-cells = <0>;
+	};
+
+	pdm_sound: pdm-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "microphone";
+
+		simple-audio-card,cpu {
+			sound-dai = <&pdm>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&pdm_codec>;
+		};
+	};
+
+	spdif_dit: spdif-dit {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_sound: spdif-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&spdif_dit>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <300>;
+		reset-gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
+	};
+
+	dc_12v: regulator-dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	pcie30_avdd0v9: regulator-pcie30-avdd0v9 {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: regulator-pcie30-avdd1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcc3v3_sys: regulator-vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc3v3_pcie: regulator-vcc3v3-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc3v3_pcie_en_pin>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <5000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb: regulator-vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb_host: regulator-vcc5v0-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: regulator-vcc5v0-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+};
+
+&can1 {
+	assigned-clocks = <&cru CLK_CAN1>;
+	assigned-clock-rates = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1m1_pins>;
+	status = "okay";
+};
+
+/* used for usb_host0_xhci */
+&combphy0 {
+	status = "okay";
+};
+
+/* used for usb_host1_xhci */
+&combphy1 {
+	status = "okay";
+};
+
+/* connected to sata2 */
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac0 {
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_tx_bus2
+		     &gmac0_rx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus>;
+	phy-handle = <&rgmii_phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+		system-power-controller;
+		#sound-dai-cells = <0>;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+
+		codec {
+			rockchip,mic-in-differential;
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	rtc0: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+	};
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_lrcktx &i2s1m0_sdi0 &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+/* used for AP6356S Bluetooth Sound */
+&i2s3_2ch {
+	status = "okay";
+};
+
+&mdio0 {
+	rgmii_phy0: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
+&pcie30phy {
+	status = "okay";
+};
+
+&pcie3x2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_pin>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pdm {
+	status = "okay";
+};
+
+&pinctrl {
+	leds {
+		led_work_en: led_work_en {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable: wifi-enable {
+			rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_reset_pin: pcie-reset-pin {
+			rockchip,pins = <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc3v3_pcie_en_pin: vcc3v3-pcie-en-pin {
+			rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&pwm5 {
+	status = "okay";
+};
+
+/* Required remotectl for IR receiver */
+&pwm7 {
+	status = "disabled";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sata2 {
+	status = "okay";
+};
+
+/* used for eMMC */
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	status = "okay";
+};
+
+/* used for microSD (TF) Slot */
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+/* used for AP6356S WiFi */
+&sdmmc2 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+/* used for Debug */
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-0 = <&uart3m1_xfer>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-0 = <&uart4m1_xfer>;
+	status = "okay";
+};
+
+/* used for WiFi/BT AP6356S */
+&uart8 {
+	pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn>;
+	status = "okay";
+};
+
+&uart9 {
+	pinctrl-0 = <&uart9m1_xfer>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
-- 
2.47.3

Re: [PATCH v2 3/3] arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Medium] The `press-threshold-microvolt` values for the ADC keys are incorrectly set to the midpoints instead of the nominal voltages, breaking the closest-match logic.
- [Medium] The `uart8` pinmux configuration for the AP6356S Bluetooth module omits the RTS pin, breaking hardware flow control.
--

commit fa96250010d1434d5bd9c7fed26ebc77f8c2f9f1
Author: Coia Prant <coiaprant@gmail.com>

arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

This patch adds support for the Graperain G3568 v2, an RK3568-based
development board. It defines the device tree including CPU, memory, network,
wireless, storage, display, and standard IO interfaces.

Link: https://image.chukouplus.com/upload/C_153/product_file/20211022/6daddec9e400458816dd4c57ba807fc3.pdf
Link: https://blog.gov.cooking/archives/research-graperain-g3568-v2-and-flash.html

> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts b/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts
> new file mode 100644
> index 0000000000000..221992d6c6003
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-graperain-g3568-v2.dts
> @@ -0,0 +1,894 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)

[ ... ]

> +	adc-keys {
> +		compatible = "adc-keys";
> +		io-channels = <&saradc 0>;
> +		io-channel-names = "buttons";
> +		keyup-threshold-microvolt = <1800000>;
> +		poll-interval = <100>;
> +
> +		button-esc {
> +			label = "esc";
> +			linux,code = <KEY_ESC>;
> +			press-threshold-microvolt = <1250000>;
> +		};
> +
> +		button-menu {
> +			label = "menu";
> +			linux,code = <KEY_MENU>;
> +			press-threshold-microvolt = <1600000>;
> +		};

[Severity: Medium]
Are these threshold values correct? The commit message declares nominal
voltages (e.g., 1.1V for ESC and 1.4V for MENU), but the values here seem to
be configured to the midpoints.

The adc-keys driver dynamically matches the read voltage to the closest
defined threshold. By configuring midpoints instead of actual nominal
voltages, the distance calculations can become skewed.

For example, when the MENU key (nominal 1.4V) is pressed, its distance to
the configured MENU threshold (1.6V) is 200mV, but its distance to the ESC
threshold (1.25V) is only 150mV.

Won't the driver incorrectly register the MENU key as ESC?

> +		button-vol-down {
> +			label = "volume down";
> +			linux,code = <KEY_VOLUMEDOWN>;
> +			press-threshold-microvolt = <600000>;
> +		};
> +
> +		button-vol-up {
> +			label = "volume up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			press-threshold-microvolt = <100000>;
> +		};
> +	};

[ ... ]

> +/* used for WiFi/BT AP6356S */
> +&uart8 {
> +	pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn>;
> +	status = "okay";
> +};

[Severity: Medium]
Does this UART configuration omit the RTS pin (&uart8m0_rtsn)?

High-speed Bluetooth modules like the AP6356S require hardware flow control to
prevent packet loss. Without the host RTS pin explicitly muxed, the Bluetooth
module may receive an invalid or floating RTS signal.

Could this prevent it from successfully transmitting data to the host or
cause buffer overflows when hardware flow control is utilized?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260630153810.3574714-2-coiaprant@gmail.com?part=3