All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jisheng Zhang <jszhang@kernel.org>
To: Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Frank Li <Frank.Li@nxp.com>
Cc: linux-i3c@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2] i3c: dw: reduce do_daa time if there's no client
Date: Fri, 14 Aug 2026 12:20:15 +0800	[thread overview]
Message-ID: <20260814042015.25397-1-jszhang@kernel.org> (raw)

dw_i3c_master_daa() derives the number of newly assigned dynamic
addresses from cmd->rx_len, the ISR sets it to the number of address
slots ENTDAA left unassigned. It starts out as zero, which already
means "every address was assigned", so a timed out transfer leaves
that value in place and it gets used as a result.

If there's no client connected, the addr assign cmd times out, then
the driver calls i3c_master_add_i3c_dev_locked() to add devices that
are not there, each costing about 1s, thus adds non necessary boot
time up to (maxdev * 1)s.

Start from maxdevs instead: no address is assigned before ENTDAA runs,
and make newdevs as 0 if the existing rx_len >= maxdevs.

Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
---

since v1:
 - use another method to remove the non-necessary calling of
   i3c_master_add_i3c_dev_locked() if there's no client
 - update commit msg

 drivers/i3c/master/dw-i3c-master.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/i3c/master/dw-i3c-master.c b/drivers/i3c/master/dw-i3c-master.c
index 1053cfb05c05..883b542c7bfc 100644
--- a/drivers/i3c/master/dw-i3c-master.c
+++ b/drivers/i3c/master/dw-i3c-master.c
@@ -876,6 +876,7 @@ static int dw_i3c_master_daa(struct i3c_master_controller *m)
 		goto rpm_out;
 	}
 	cmd = &xfer->cmds[0];
+	cmd->rx_len = master->maxdevs;
 	cmd->cmd_hi = COMMAND_PORT_TRANSFER_ARG;
 	cmd->cmd_lo = COMMAND_PORT_DEV_COUNT(master->maxdevs - pos) |
 		      COMMAND_PORT_DEV_INDEX(pos) |
@@ -888,7 +889,10 @@ static int dw_i3c_master_daa(struct i3c_master_controller *m)
 	if (!wait_for_completion_timeout(&xfer->comp, XFER_TIMEOUT))
 		dw_i3c_master_dequeue_xfer(master, xfer);
 
-	newdevs = GENMASK(master->maxdevs - cmd->rx_len - 1, 0);
+	if (cmd->rx_len >= master->maxdevs)
+		newdevs = 0;
+	else
+		newdevs = GENMASK(master->maxdevs - cmd->rx_len - 1, 0);
 	newdevs &= ~olddevs;
 
 	for (pos = 0; pos < master->maxdevs; pos++) {
-- 
2.51.0


-- 
linux-i3c mailing list
linux-i3c@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-i3c

WARNING: multiple messages have this Message-ID (diff)
From: Jisheng Zhang <jszhang@kernel.org>
To: Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Frank Li <Frank.Li@nxp.com>
Cc: linux-i3c@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2] i3c: dw: reduce do_daa time if there's no client
Date: Fri, 14 Aug 2026 12:20:15 +0800	[thread overview]
Message-ID: <20260814042015.25397-1-jszhang@kernel.org> (raw)

dw_i3c_master_daa() derives the number of newly assigned dynamic
addresses from cmd->rx_len, the ISR sets it to the number of address
slots ENTDAA left unassigned. It starts out as zero, which already
means "every address was assigned", so a timed out transfer leaves
that value in place and it gets used as a result.

If there's no client connected, the addr assign cmd times out, then
the driver calls i3c_master_add_i3c_dev_locked() to add devices that
are not there, each costing about 1s, thus adds non necessary boot
time up to (maxdev * 1)s.

Start from maxdevs instead: no address is assigned before ENTDAA runs,
and make newdevs as 0 if the existing rx_len >= maxdevs.

Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
---

since v1:
 - use another method to remove the non-necessary calling of
   i3c_master_add_i3c_dev_locked() if there's no client
 - update commit msg

 drivers/i3c/master/dw-i3c-master.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/i3c/master/dw-i3c-master.c b/drivers/i3c/master/dw-i3c-master.c
index 1053cfb05c05..883b542c7bfc 100644
--- a/drivers/i3c/master/dw-i3c-master.c
+++ b/drivers/i3c/master/dw-i3c-master.c
@@ -876,6 +876,7 @@ static int dw_i3c_master_daa(struct i3c_master_controller *m)
 		goto rpm_out;
 	}
 	cmd = &xfer->cmds[0];
+	cmd->rx_len = master->maxdevs;
 	cmd->cmd_hi = COMMAND_PORT_TRANSFER_ARG;
 	cmd->cmd_lo = COMMAND_PORT_DEV_COUNT(master->maxdevs - pos) |
 		      COMMAND_PORT_DEV_INDEX(pos) |
@@ -888,7 +889,10 @@ static int dw_i3c_master_daa(struct i3c_master_controller *m)
 	if (!wait_for_completion_timeout(&xfer->comp, XFER_TIMEOUT))
 		dw_i3c_master_dequeue_xfer(master, xfer);
 
-	newdevs = GENMASK(master->maxdevs - cmd->rx_len - 1, 0);
+	if (cmd->rx_len >= master->maxdevs)
+		newdevs = 0;
+	else
+		newdevs = GENMASK(master->maxdevs - cmd->rx_len - 1, 0);
 	newdevs &= ~olddevs;
 
 	for (pos = 0; pos < master->maxdevs; pos++) {
-- 
2.51.0


             reply	other threads:[~2026-08-14  4:39 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-08-14  4:20 Jisheng Zhang [this message]
2026-08-14  4:20 ` [PATCH v2] i3c: dw: reduce do_daa time if there's no client Jisheng Zhang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260814042015.25397-1-jszhang@kernel.org \
    --to=jszhang@kernel.org \
    --cc=Frank.Li@nxp.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=linux-i3c@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.