* [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files
@ 2026-08-24 19:48 Tom Rini
2026-08-24 19:48 ` [PATCH v2 1/5] dts: Correct behavior of OF_OMIT_DTB Tom Rini
` (6 more replies)
0 siblings, 7 replies; 9+ messages in thread
From: Tom Rini @ 2026-08-24 19:48 UTC (permalink / raw)
To: u-boot
Hey all,
This series depends on the series to correct the logic around
BLOBLIST_PASSAGE_MANDATORY and found at
https://lore.kernel.org/r/20260824194814.555634-1-trini@konsulko.com/
In this series we correct how we handle OF_OMIT_DTB so that we can in
turn not have an empty or fake dts file in the tree, when we are
building for the case where we would be omitting building the final part
of the dtb for use anyhow. With the changes in the previous series, we
can then correct the Kconfig logic around OF_OMIT_DTB and
DEFAULT_DEVICE_TREE so that when we're omitting the device tree binary
we don't try and build one anyhow. Finally, we can remove all of the
empty / fake device tree sources we have, or in some cases have but
never used.
Changes in v2:
- Split the previous series in two. No actual changes made.
--
Tom
^ permalink raw reply [flat|nested] 9+ messages in thread* [PATCH v2 1/5] dts: Correct behavior of OF_OMIT_DTB 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini @ 2026-08-24 19:48 ` Tom Rini 2026-08-24 19:48 ` [PATCH v2 2/5] dts: Make DEFAULT_DEVICE_TREE depend on !OF_OMIT_DTB Tom Rini ` (5 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Tom Rini @ 2026-08-24 19:48 UTC (permalink / raw) To: u-boot When we have enabled CONFIG_OF_OMIT_DTB, we really should then be not forcing a device tree to be built. This involves two things. First, when OF_SEPARATE is set, don't say we still need to build dts/dt.dtb. Second, our init_sp_bss_offset_check check can only cover the non-dtb portion. Signed-off-by: Tom Rini <trini@konsulko.com> --- Makefile | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/Makefile b/Makefile index 98702205c36d..56a8ca9fb4bb 100644 --- a/Makefile +++ b/Makefile @@ -1237,7 +1237,7 @@ INPUTS-$(CONFIG_TPL) += tpl/u-boot-tpl.bin INPUTS-$(CONFIG_VPL) += vpl/u-boot-vpl.bin # Allow omitting the .dtb output if it is not normally used -INPUTS-$(CONFIG_OF_SEPARATE) += $(if $(CONFIG_OF_OMIT_DTB),dts/dt.dtb,u-boot.dtb) +INPUTS-$(CONFIG_OF_SEPARATE) += $(if $(CONFIG_OF_OMIT_DTB),,u-boot.dtb) ifeq ($(CONFIG_SPL_FRAMEWORK),y) INPUTS-$(CONFIG_OF_SEPARATE) += u-boot-dtb.img endif @@ -1615,12 +1615,18 @@ endif # The 1/4 margin below is somewhat arbitrary. The likely initial SP usage is # so low that the DTB could probably use 90%+ of the available space, for # current values of CONFIG_SYS_INIT_SP_BSS_OFFSET at least. However, let's be -# safe for now and tweak this later if space becomes tight. +# safe for now and tweak this later if space becomes tight. When we omit the +# DTB we simply have to have accounted for this when configuring U-Boot. # A rejected alternative would be to check that some absolute minimum stack # space was available. However, since CONFIG_SYS_INIT_SP_BSS_OFFSET is # deliberately build-specific, to take account of build-to-build stack usage # differences due to different feature sets, there is no common absolute value # to check against. +ifneq ($(CONFIG_OF_OMIT_DTB),) +init_sp_bss_offset_check: FORCE + space=$(CONFIG_SYS_INIT_SP_BSS_OFFSET) ; \ + $(subtract_sys_malloc_f_len) +else init_sp_bss_offset_check: u-boot.dtb FORCE @dtb_size=$(shell wc -c u-boot.dtb | awk '{print $$1}') ; \ space=$(CONFIG_SYS_INIT_SP_BSS_OFFSET) ; \ @@ -1632,6 +1638,7 @@ init_sp_bss_offset_check: u-boot.dtb FORCE exit 1 ; \ fi endif +endif shell_cmd = { $(call echo-cmd,$(1)) $(cmd_$(1)); } -- 2.43.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v2 2/5] dts: Make DEFAULT_DEVICE_TREE depend on !OF_OMIT_DTB 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini 2026-08-24 19:48 ` [PATCH v2 1/5] dts: Correct behavior of OF_OMIT_DTB Tom Rini @ 2026-08-24 19:48 ` Tom Rini 2026-08-24 19:48 ` [PATCH v2 3/5] dts: Correct entry for OF_OMIT_DTB Tom Rini ` (4 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Tom Rini @ 2026-08-24 19:48 UTC (permalink / raw) To: u-boot When we have configured the board to not omit a DTB as part of the build, we should not have to say that we still need to build a default DTB for the board. Signed-off-by: Tom Rini <trini@konsulko.com> --- dts/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/dts/Kconfig b/dts/Kconfig index d56d94679f5d..b7a2d12a73b5 100644 --- a/dts/Kconfig +++ b/dts/Kconfig @@ -224,7 +224,7 @@ config OF_OMIT_DTB config DEFAULT_DEVICE_TREE string "Default Device Tree for DT control" - depends on OF_CONTROL + depends on OF_CONTROL && !OF_OMIT_DTB default "sandbox" if SANDBOX help This option specifies the default Device Tree used for DT control. -- 2.43.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v2 3/5] dts: Correct entry for OF_OMIT_DTB 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini 2026-08-24 19:48 ` [PATCH v2 1/5] dts: Correct behavior of OF_OMIT_DTB Tom Rini 2026-08-24 19:48 ` [PATCH v2 2/5] dts: Make DEFAULT_DEVICE_TREE depend on !OF_OMIT_DTB Tom Rini @ 2026-08-24 19:48 ` Tom Rini 2026-08-24 19:48 ` [PATCH v2 4/5] powerpc: drop qemu-ppce500 dts Tom Rini ` (3 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Tom Rini @ 2026-08-24 19:48 UTC (permalink / raw) To: u-boot When we omit writing a device tree file is not something that should be prompted for but rather it should be selected when needed, and the "default y if ..." conditions should be used for when this should be enabled without being selected. Signed-off-by: Tom Rini <trini@konsulko.com> --- dts/Kconfig | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/dts/Kconfig b/dts/Kconfig index b7a2d12a73b5..a2973ef40860 100644 --- a/dts/Kconfig +++ b/dts/Kconfig @@ -213,8 +213,7 @@ config OF_HAS_PRIOR_STAGE disabled in the board's defconfig file. config OF_OMIT_DTB - bool "Omit the device tree output when building" - default y if OF_HAS_PRIOR_STAGE && !BINMAN + def_bool y if OF_HAS_PRIOR_STAGE && !BINMAN help As a special case, avoid writing a device tree file u-boot.dtb when building. Also don't include that file in u-boot.bin -- 2.43.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v2 4/5] powerpc: drop qemu-ppce500 dts 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini ` (2 preceding siblings ...) 2026-08-24 19:48 ` [PATCH v2 3/5] dts: Correct entry for OF_OMIT_DTB Tom Rini @ 2026-08-24 19:48 ` Tom Rini 2026-08-24 19:48 ` [PATCH v2 5/5] arm: Drop unused dts files Tom Rini ` (2 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Tom Rini @ 2026-08-24 19:48 UTC (permalink / raw) To: u-boot Now that we are not building this device tree, we can drop it from the tree. Signed-off-by: Tom Rini <trini@konsulko.com> --- arch/powerpc/dts/Makefile | 1 - arch/powerpc/dts/qemu-ppce500.dts | 10 ---------- 2 files changed, 11 deletions(-) delete mode 100644 arch/powerpc/dts/qemu-ppce500.dts diff --git a/arch/powerpc/dts/Makefile b/arch/powerpc/dts/Makefile index 4fd3478ac2fa..a9075c16fefc 100644 --- a/arch/powerpc/dts/Makefile +++ b/arch/powerpc/dts/Makefile @@ -17,7 +17,6 @@ dtb-$(CONFIG_TARGET_P2020RDB) += p2020rdb-pc.dtb p2020rdb-pc_36b.dtb dtb-$(CONFIG_TARGET_P3041DS) += p3041ds.dtb dtb-$(CONFIG_TARGET_P4080DS) += p4080ds.dtb dtb-$(CONFIG_TARGET_P5040DS) += p5040ds.dtb -dtb-$(CONFIG_TARGET_QEMU_PPCE500) += qemu-ppce500.dtb dtb-$(CONFIG_TARGET_SOCRATES) += socrates.dtb dtb-$(CONFIG_TARGET_T1024RDB) += t1024rdb.dtb dtb-$(CONFIG_TARGET_T1042D4RDB) += t1042d4rdb.dtb diff --git a/arch/powerpc/dts/qemu-ppce500.dts b/arch/powerpc/dts/qemu-ppce500.dts deleted file mode 100644 index e88e09e17961..000000000000 --- a/arch/powerpc/dts/qemu-ppce500.dts +++ /dev/null @@ -1,10 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ OR MIT -/* - * Empty device tree for qemu-ppce400 - * - * Copyright 2021 Google LLC - */ -/dts-v1/; - -/ { -}; -- 2.43.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v2 5/5] arm: Drop unused dts files 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini ` (3 preceding siblings ...) 2026-08-24 19:48 ` [PATCH v2 4/5] powerpc: drop qemu-ppce500 dts Tom Rini @ 2026-08-24 19:48 ` Tom Rini 2026-08-24 20:09 ` Peter Robinson 2026-08-25 16:36 ` [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless " Yao Zi 2026-09-04 1:30 ` Tom Rini 6 siblings, 1 reply; 9+ messages in thread From: Tom Rini @ 2026-08-24 19:48 UTC (permalink / raw) To: u-boot Now that we do not require device tree files to be built when OF_OMIT_DTB is set, we can remove a number of unused dts files. Signed-off-by: Tom Rini <trini@konsulko.com> --- arch/arm/dts/Makefile | 27 +- arch/arm/dts/arm_fvp.dts | 11 - arch/arm/dts/bcm2711-rpi-4-b.dts | 262 ----- arch/arm/dts/bcm2711-rpi.dtsi | 74 -- arch/arm/dts/bcm2711.dtsi | 1100 ------------------ arch/arm/dts/bcm2835-common.dtsi | 207 ---- arch/arm/dts/bcm2835-rpi-a-plus.dts | 128 -- arch/arm/dts/bcm2835-rpi-a.dts | 123 -- arch/arm/dts/bcm2835-rpi-b-plus.dts | 130 --- arch/arm/dts/bcm2835-rpi-b-rev2.dts | 123 -- arch/arm/dts/bcm2835-rpi-b.dts | 118 -- arch/arm/dts/bcm2835-rpi-cm1-io1.dts | 97 -- arch/arm/dts/bcm2835-rpi-cm1.dtsi | 39 - arch/arm/dts/bcm2835-rpi-common.dtsi | 12 - arch/arm/dts/bcm2835-rpi-zero-w.dts | 151 --- arch/arm/dts/bcm2835-rpi-zero.dts | 119 -- arch/arm/dts/bcm2835-rpi.dtsi | 81 -- arch/arm/dts/bcm2835.dtsi | 38 - arch/arm/dts/bcm2836-rpi-2-b.dts | 130 --- arch/arm/dts/bcm2836-rpi.dtsi | 6 - arch/arm/dts/bcm2836.dtsi | 92 -- arch/arm/dts/bcm2837-rpi-3-a-plus.dts | 180 --- arch/arm/dts/bcm2837-rpi-3-b-plus.dts | 183 --- arch/arm/dts/bcm2837-rpi-3-b.dts | 176 --- arch/arm/dts/bcm2837-rpi-cm3-io3.dts | 96 -- arch/arm/dts/bcm2837-rpi-cm3.dtsi | 61 - arch/arm/dts/bcm2837.dtsi | 95 -- arch/arm/dts/bcm283x-rpi-lan7515.dtsi | 41 - arch/arm/dts/bcm283x-rpi-smsc9512.dtsi | 20 - arch/arm/dts/bcm283x-rpi-smsc9514.dtsi | 19 - arch/arm/dts/bcm283x-rpi-usb-host.dtsi | 3 - arch/arm/dts/bcm283x-rpi-usb-otg.dtsi | 11 - arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi | 7 - arch/arm/dts/bcm283x-u-boot.dtsi | 29 - arch/arm/dts/bcm283x.dtsi | 501 -------- arch/arm/dts/bcm7xxx.dts | 15 - arch/arm/dts/highbank.dts | 9 - arch/arm/dts/octeontx.dts | 14 - arch/arm/dts/qemu-arm.dts | 11 - arch/arm/dts/xenguest-arm64.dts | 15 - 40 files changed, 1 insertion(+), 4553 deletions(-) delete mode 100644 arch/arm/dts/arm_fvp.dts delete mode 100644 arch/arm/dts/bcm2711-rpi-4-b.dts delete mode 100644 arch/arm/dts/bcm2711-rpi.dtsi delete mode 100644 arch/arm/dts/bcm2711.dtsi delete mode 100644 arch/arm/dts/bcm2835-common.dtsi delete mode 100644 arch/arm/dts/bcm2835-rpi-a-plus.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-a.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-b-plus.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-b-rev2.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-b.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-cm1-io1.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-cm1.dtsi delete mode 100644 arch/arm/dts/bcm2835-rpi-common.dtsi delete mode 100644 arch/arm/dts/bcm2835-rpi-zero-w.dts delete mode 100644 arch/arm/dts/bcm2835-rpi-zero.dts delete mode 100644 arch/arm/dts/bcm2835-rpi.dtsi delete mode 100644 arch/arm/dts/bcm2835.dtsi delete mode 100644 arch/arm/dts/bcm2836-rpi-2-b.dts delete mode 100644 arch/arm/dts/bcm2836-rpi.dtsi delete mode 100644 arch/arm/dts/bcm2836.dtsi delete mode 100644 arch/arm/dts/bcm2837-rpi-3-a-plus.dts delete mode 100644 arch/arm/dts/bcm2837-rpi-3-b-plus.dts delete mode 100644 arch/arm/dts/bcm2837-rpi-3-b.dts delete mode 100644 arch/arm/dts/bcm2837-rpi-cm3-io3.dts delete mode 100644 arch/arm/dts/bcm2837-rpi-cm3.dtsi delete mode 100644 arch/arm/dts/bcm2837.dtsi delete mode 100644 arch/arm/dts/bcm283x-rpi-lan7515.dtsi delete mode 100644 arch/arm/dts/bcm283x-rpi-smsc9512.dtsi delete mode 100644 arch/arm/dts/bcm283x-rpi-smsc9514.dtsi delete mode 100644 arch/arm/dts/bcm283x-rpi-usb-host.dtsi delete mode 100644 arch/arm/dts/bcm283x-rpi-usb-otg.dtsi delete mode 100644 arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi delete mode 100644 arch/arm/dts/bcm283x-u-boot.dtsi delete mode 100644 arch/arm/dts/bcm283x.dtsi delete mode 100644 arch/arm/dts/bcm7xxx.dts delete mode 100644 arch/arm/dts/highbank.dts delete mode 100644 arch/arm/dts/octeontx.dts delete mode 100644 arch/arm/dts/qemu-arm.dts delete mode 100644 arch/arm/dts/xenguest-arm64.dts diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 1b533721bb43..782867f3fec3 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -834,8 +834,6 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \ imx7ulp-evk.dtb -dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb - dtb-$(CONFIG_ARCH_IMX8) += \ fsl-imx8qm-apalis.dtb \ fsl-imx8qm-mek.dtb \ @@ -962,28 +960,10 @@ dtb-$(CONFIG_TARGET_SAMA5D4_XPLAINED) += \ dtb-$(CONFIG_TARGET_VINCO) += \ at91-vinco.dtb -dtb-$(CONFIG_ARCH_BCM283X) += \ - bcm2835-rpi-a.dtb \ - bcm2835-rpi-a-plus.dtb \ - bcm2835-rpi-b.dtb \ - bcm2835-rpi-b-plus.dtb \ - bcm2835-rpi-b-rev2.dtb \ - bcm2835-rpi-cm1-io1.dtb \ - bcm2835-rpi-zero.dtb \ - bcm2835-rpi-zero-w.dtb\ - bcm2836-rpi-2-b.dtb \ - bcm2837-rpi-3-a-plus.dtb \ - bcm2837-rpi-3-b.dtb \ - bcm2837-rpi-3-b-plus.dtb \ - bcm2837-rpi-cm3-io3.dtb \ - bcm2711-rpi-4-b.dtb - dtb-$(CONFIG_TARGET_BCMNS) += ns-board.dtb dtb-$(CONFIG_TARGET_BCMNS3) += ns3-board.dtb -dtb-$(CONFIG_ARCH_BCMSTB) += bcm7xxx.dtb - dtb-$(CONFIG_BCM47622) += \ bcm947622.dtb dtb-$(CONFIG_BCM4908) += \ @@ -1099,10 +1079,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ dtb-$(CONFIG_ARCH_NPCM7xx) += nuvoton-npcm750-evb.dtb dtb-$(CONFIG_ARCH_NPCM8XX) += nuvoton-npcm845-evb.dtb -dtb-$(CONFIG_XEN) += xenguest-arm64.dtb - -dtb-$(CONFIG_ARCH_OCTEONTX) += octeontx.dtb -dtb-$(CONFIG_ARCH_OCTEONTX2) += octeontx.dtb dtb-$(CONFIG_TARGET_GE_BX50V3) += \ imx6q-bx50v3.dtb \ @@ -1117,7 +1093,6 @@ dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb # Kconfig option to build all of these. See examples above. dtb-$(CONFIG_TARGET_VEXPRESS_CA9X4) += vexpress-v2p-ca9.dtb dtb-$(CONFIG_TARGET_VEXPRESS64_BASE_FVP) += fvp-base-revc.dtb -dtb-$(CONFIG_TARGET_VEXPRESS64_BASER_FVP) += arm_fvp.dtb dtb-$(CONFIG_TARGET_VEXPRESS64_JUNO) += juno-r2.dtb dtb-$(CONFIG_TARGET_TOTAL_COMPUTE) += total_compute.dtb @@ -1163,7 +1138,7 @@ endif dtb-$(CONFIG_TARGET_EA_LPC3250DEVKITV2) += lpc3250-ea3250.dtb -dtb-$(CONFIG_ARCH_QEMU) += qemu-arm.dtb qemu-arm64.dtb +dtb-$(CONFIG_TARGET_QEMU_ARM_64BIT) += qemu-arm64.dtb dtb-$(CONFIG_TARGET_CORSTONE1000) += corstone1000-mps3.dtb \ corstone1000-fvp.dtb diff --git a/arch/arm/dts/arm_fvp.dts b/arch/arm/dts/arm_fvp.dts deleted file mode 100644 index 3a4ad5d18012..000000000000 --- a/arch/arm/dts/arm_fvp.dts +++ /dev/null @@ -1,11 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ OR MIT -/* - * Empty device tree for the Arm Ltd FVP platform model - - * Copyright 2022 Arm Ltd. - */ - -/dts-v1/; - -/ { -}; diff --git a/arch/arm/dts/bcm2711-rpi-4-b.dts b/arch/arm/dts/bcm2711-rpi-4-b.dts deleted file mode 100644 index 72ce80fbf266..000000000000 --- a/arch/arm/dts/bcm2711-rpi-4-b.dts +++ /dev/null @@ -1,262 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2711.dtsi" -#include "bcm2711-rpi.dtsi" -#include "bcm283x-rpi-usb-peripheral.dtsi" - -/ { - compatible = "raspberrypi,4-model-b", "brcm,bcm2711"; - model = "Raspberry Pi 4 Model B"; - - chosen { - /* 8250 auxiliary UART instead of pl011 */ - stdout-path = "serial1:115200n8"; - }; - - leds { - led-act { - gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; - }; - - led-pwr { - label = "PWR"; - gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - linux,default-trigger = "default-on"; - }; - }; - - wifi_pwrseq: wifi-pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; - }; - - sd_io_1v8_reg: sd_io_1v8_reg { - compatible = "regulator-gpio"; - regulator-name = "vdd-sd-io"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - regulator-settling-time-us = <5000>; - gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1>, - <3300000 0x0>; - status = "okay"; - }; - - sd_vcc_reg: sd_vcc_reg { - compatible = "regulator-fixed"; - regulator-name = "vcc-sd"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - enable-active-high; - gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; - }; -}; - -&ddc0 { - status = "okay"; -}; - -&ddc1 { - status = "okay"; -}; - -&expgpio { - gpio-line-names = "BT_ON", - "WL_ON", - "PWR_LED_OFF", - "GLOBAL_RESET", - "VDD_SD_IO_SEL", - "CAM_GPIO", - "SD_PWR_ON", - ""; -}; - -&gpio { - /* - * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and - * the official GPU firmware DT blob. - * - * Legend: - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD1", - "RXD1", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "RGMII_MDIO", - "RGMIO_MDC", - /* Used by BT module */ - "CTS0", - "RTS0", - "TXD0", - "RXD0", - /* Used by Wifi */ - "SD1_CLK", - "SD1_CMD", - "SD1_DATA0", - "SD1_DATA1", - "SD1_DATA2", - "SD1_DATA3", - /* Shared with SPI flash */ - "PWM0_MISO", - "PWM1_MOSI", - "STATUS_LED_G_CLK", - "SPIFLASH_CE_N", - "SDA0", - "SCL0", - "RGMII_RXCLK", - "RGMII_RXCTL", - "RGMII_RXD0", - "RGMII_RXD1", - "RGMII_RXD2", - "RGMII_RXD3", - "RGMII_TXCLK", - "RGMII_TXCTL", - "RGMII_TXD0", - "RGMII_TXD1", - "RGMII_TXD2", - "RGMII_TXD3"; -}; - -&hdmi0 { - status = "okay"; -}; - -&hdmi1 { - status = "okay"; -}; - -&pixelvalve0 { - status = "okay"; -}; - -&pixelvalve1 { - status = "okay"; -}; - -&pixelvalve2 { - status = "okay"; -}; - -&pixelvalve4 { - status = "okay"; -}; - -&pwm1 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>; - status = "okay"; -}; - -/* SDHCI is used to control the SDIO for wireless */ -&sdhci { - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio34>; - bus-width = <4>; - non-removable; - mmc-pwrseq = <&wifi_pwrseq>; - status = "okay"; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -/* EMMC2 is used to drive the SD card */ -&emmc2 { - vqmmc-supply = <&sd_io_1v8_reg>; - vmmc-supply = <&sd_vcc_reg>; - broken-cd; - status = "okay"; -}; - -&genet { - phy-handle = <&phy1>; - phy-mode = "rgmii-rxid"; - status = "okay"; -}; - -&genet_mdio { - phy1: ethernet-phy@1 { - /* No PHY interrupt */ - reg = <0x1>; - }; -}; - -&pcie0 { - pci@0,0 { - device_type = "pci"; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - reg = <0 0 0 0 0>; - - usb@0,0 { - reg = <0 0 0 0 0>; - resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>; - }; - }; -}; - -/* uart0 communicates with the BT module */ -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; - uart-has-rtscts; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <2000000>; - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; - }; -}; - -/* uart1 is mapped to the pin header */ -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_gpio14>; - status = "okay"; -}; - -&vc4 { - status = "okay"; -}; - -&vec { - status = "disabled"; -}; diff --git a/arch/arm/dts/bcm2711-rpi.dtsi b/arch/arm/dts/bcm2711-rpi.dtsi deleted file mode 100644 index ca266c5d9f9b..000000000000 --- a/arch/arm/dts/bcm2711-rpi.dtsi +++ /dev/null @@ -1,74 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "bcm2835-rpi.dtsi" - -#include <dt-bindings/reset/raspberrypi,firmware-reset.h> - -/ { - /* Will be filled by the bootloader */ - memory@0 { - device_type = "memory"; - reg = <0 0 0>; - }; - - aliases { - emmc2bus = &emmc2bus; - ethernet0 = &genet; - pcie0 = &pcie0; - blconfig = &blconfig; - }; -}; - -&firmware { - firmware_clocks: clocks { - compatible = "raspberrypi,firmware-clocks"; - #clock-cells = <1>; - }; - - expgpio: gpio { - compatible = "raspberrypi,firmware-gpio"; - gpio-controller; - #gpio-cells = <2>; - status = "okay"; - }; - - reset: reset { - compatible = "raspberrypi,firmware-reset"; - #reset-cells = <1>; - }; -}; - -&hdmi0 { - clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>; - clock-names = "hdmi", "bvb", "audio", "cec"; - wifi-2.4ghz-coexistence; -}; - -&hdmi1 { - clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>; - clock-names = "hdmi", "bvb", "audio", "cec"; - wifi-2.4ghz-coexistence; -}; - -&hvs { - clocks = <&firmware_clocks 4>; -}; - -&rmem { - /* - * RPi4's co-processor will copy the board's bootloader configuration - * into memory for the OS to consume. It'll also update this node with - * its placement information. - */ - blconfig: nvram@0 { - compatible = "raspberrypi,bootloader-config", "nvmem-rmem"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x0 0x0 0x0>; - no-map; - status = "disabled"; - }; -}; - -&vchiq { - interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/arch/arm/dts/bcm2711.dtsi b/arch/arm/dts/bcm2711.dtsi deleted file mode 100644 index 3b60297af7f6..000000000000 --- a/arch/arm/dts/bcm2711.dtsi +++ /dev/null @@ -1,1100 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "bcm283x.dtsi" - -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/soc/bcm2835-pm.h> - -/ { - compatible = "brcm,bcm2711"; - - #address-cells = <2>; - #size-cells = <1>; - - interrupt-parent = <&gicv2>; - - vc4: gpu { - compatible = "brcm,bcm2711-vc5"; - status = "disabled"; - }; - - clk_27MHz: clk-27M { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <27000000>; - clock-output-names = "27MHz-clock"; - }; - - clk_108MHz: clk-108M { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <108000000>; - clock-output-names = "108MHz-clock"; - }; - - soc { - /* - * Defined ranges: - * Common BCM283x peripherals - * BCM2711-specific peripherals - * ARM-local peripherals - */ - ranges = <0x7e000000 0x0 0xfe000000 0x01800000>, - <0x7c000000 0x0 0xfc000000 0x02000000>, - <0x40000000 0x0 0xff800000 0x00800000>; - /* Emulate a contiguous 30-bit address range for DMA */ - dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>; - - /* - * This node is the provider for the enable-method for - * bringing up secondary cores. - */ - local_intc: local_intc@40000000 { - compatible = "brcm,bcm2836-l1-intc"; - reg = <0x40000000 0x100>; - }; - - gicv2: interrupt-controller@40041000 { - interrupt-controller; - #interrupt-cells = <3>; - compatible = "arm,gic-400"; - reg = <0x40041000 0x1000>, - <0x40042000 0x2000>, - <0x40044000 0x2000>, - <0x40046000 0x2000>; - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | - IRQ_TYPE_LEVEL_HIGH)>; - }; - - avs_monitor: avs-monitor@7d5d2000 { - compatible = "brcm,bcm2711-avs-monitor", - "syscon", "simple-mfd"; - reg = <0x7d5d2000 0xf00>; - - thermal: thermal { - compatible = "brcm,bcm2711-thermal"; - #thermal-sensor-cells = <0>; - }; - }; - - dma: dma@7e007000 { - compatible = "brcm,bcm2835-dma"; - reg = <0x7e007000 0xb00>; - interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, - /* DMA lite 7 - 10 */ - <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "dma0", - "dma1", - "dma2", - "dma3", - "dma4", - "dma5", - "dma6", - "dma7", - "dma8", - "dma9", - "dma10"; - #dma-cells = <1>; - brcm,dma-channel-mask = <0x07f5>; - }; - - pm: watchdog@7e100000 { - compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; - #power-domain-cells = <1>; - #reset-cells = <1>; - reg = <0x7e100000 0x114>, - <0x7e00a000 0x24>, - <0x7ec11000 0x20>; - clocks = <&clocks BCM2835_CLOCK_V3D>, - <&clocks BCM2835_CLOCK_PERI_IMAGE>, - <&clocks BCM2835_CLOCK_H264>, - <&clocks BCM2835_CLOCK_ISP>; - clock-names = "v3d", "peri_image", "h264", "isp"; - system-power-controller; - }; - - rng@7e104000 { - compatible = "brcm,bcm2711-rng200"; - reg = <0x7e104000 0x28>; - }; - - uart2: serial@7e201400 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x7e201400 0x200>; - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_UART>, - <&clocks BCM2835_CLOCK_VPU>; - clock-names = "uartclk", "apb_pclk"; - arm,primecell-periphid = <0x00241011>; - status = "disabled"; - }; - - uart3: serial@7e201600 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x7e201600 0x200>; - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_UART>, - <&clocks BCM2835_CLOCK_VPU>; - clock-names = "uartclk", "apb_pclk"; - arm,primecell-periphid = <0x00241011>; - status = "disabled"; - }; - - uart4: serial@7e201800 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x7e201800 0x200>; - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_UART>, - <&clocks BCM2835_CLOCK_VPU>; - clock-names = "uartclk", "apb_pclk"; - arm,primecell-periphid = <0x00241011>; - status = "disabled"; - }; - - uart5: serial@7e201a00 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x7e201a00 0x200>; - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_UART>, - <&clocks BCM2835_CLOCK_VPU>; - clock-names = "uartclk", "apb_pclk"; - arm,primecell-periphid = <0x00241011>; - status = "disabled"; - }; - - spi3: spi@7e204600 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204600 0x0200>; - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi4: spi@7e204800 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204800 0x0200>; - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi5: spi@7e204a00 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204a00 0x0200>; - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi6: spi@7e204c00 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204c00 0x0200>; - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c3: i2c@7e205600 { - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; - reg = <0x7e205600 0x200>; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c4: i2c@7e205800 { - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; - reg = <0x7e205800 0x200>; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c5: i2c@7e205a00 { - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; - reg = <0x7e205a00 0x200>; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c6: i2c@7e205c00 { - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; - reg = <0x7e205c00 0x200>; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - pixelvalve0: pixelvalve@7e206000 { - compatible = "brcm,bcm2711-pixelvalve0"; - reg = <0x7e206000 0x100>; - interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - pixelvalve1: pixelvalve@7e207000 { - compatible = "brcm,bcm2711-pixelvalve1"; - reg = <0x7e207000 0x100>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - pixelvalve2: pixelvalve@7e20a000 { - compatible = "brcm,bcm2711-pixelvalve2"; - reg = <0x7e20a000 0x100>; - interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - pwm1: pwm@7e20c800 { - compatible = "brcm,bcm2835-pwm"; - reg = <0x7e20c800 0x28>; - clocks = <&clocks BCM2835_CLOCK_PWM>; - assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; - assigned-clock-rates = <10000000>; - #pwm-cells = <2>; - status = "disabled"; - }; - - pixelvalve4: pixelvalve@7e216000 { - compatible = "brcm,bcm2711-pixelvalve4"; - reg = <0x7e216000 0x100>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - hvs: hvs@7e400000 { - compatible = "brcm,bcm2711-hvs"; - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; - }; - - pixelvalve3: pixelvalve@7ec12000 { - compatible = "brcm,bcm2711-pixelvalve3"; - reg = <0x7ec12000 0x100>; - interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - vec: vec@7ec13000 { - compatible = "brcm,bcm2711-vec"; - reg = <0x7ec13000 0x1000>; - clocks = <&clocks BCM2835_CLOCK_VEC>; - interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - dvp: clock@7ef00000 { - compatible = "brcm,brcm2711-dvp"; - reg = <0x7ef00000 0x10>; - clocks = <&clk_108MHz>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - aon_intr: interrupt-controller@7ef00100 { - compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; - reg = <0x7ef00100 0x30>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - #interrupt-cells = <1>; - }; - - hdmi0: hdmi@7ef00700 { - compatible = "brcm,bcm2711-hdmi0"; - reg = <0x7ef00700 0x300>, - <0x7ef00300 0x200>, - <0x7ef00f00 0x80>, - <0x7ef00f80 0x80>, - <0x7ef01b00 0x200>, - <0x7ef01f00 0x400>, - <0x7ef00200 0x80>, - <0x7ef04300 0x100>, - <0x7ef20000 0x100>; - reg-names = "hdmi", - "dvp", - "phy", - "rm", - "packet", - "metadata", - "csc", - "cec", - "hd"; - clock-names = "hdmi", "bvb", "audio", "cec"; - resets = <&dvp 0>; - interrupt-parent = <&aon_intr>; - interrupts = <0>, <1>, <2>, - <3>, <4>, <5>; - interrupt-names = "cec-tx", "cec-rx", "cec-low", - "wakeup", "hpd-connected", "hpd-removed"; - ddc = <&ddc0>; - dmas = <&dma 10>; - dma-names = "audio-rx"; - status = "disabled"; - }; - - ddc0: i2c@7ef04500 { - compatible = "brcm,bcm2711-hdmi-i2c"; - reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; - reg-names = "bsc", "auto-i2c"; - clock-frequency = <97500>; - status = "disabled"; - }; - - hdmi1: hdmi@7ef05700 { - compatible = "brcm,bcm2711-hdmi1"; - reg = <0x7ef05700 0x300>, - <0x7ef05300 0x200>, - <0x7ef05f00 0x80>, - <0x7ef05f80 0x80>, - <0x7ef06b00 0x200>, - <0x7ef06f00 0x400>, - <0x7ef00280 0x80>, - <0x7ef09300 0x100>, - <0x7ef20000 0x100>; - reg-names = "hdmi", - "dvp", - "phy", - "rm", - "packet", - "metadata", - "csc", - "cec", - "hd"; - ddc = <&ddc1>; - clock-names = "hdmi", "bvb", "audio", "cec"; - resets = <&dvp 1>; - interrupt-parent = <&aon_intr>; - interrupts = <8>, <7>, <6>, - <9>, <10>, <11>; - interrupt-names = "cec-tx", "cec-rx", "cec-low", - "wakeup", "hpd-connected", "hpd-removed"; - dmas = <&dma 17>; - dma-names = "audio-rx"; - status = "disabled"; - }; - - ddc1: i2c@7ef09500 { - compatible = "brcm,bcm2711-hdmi-i2c"; - reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; - reg-names = "bsc", "auto-i2c"; - clock-frequency = <97500>; - status = "disabled"; - }; - }; - - /* - * emmc2 has different DMA constraints based on SoC revisions. It was - * moved into its own bus, so as for RPi4's firmware to update them. - * The firmware will find whether the emmc2bus alias is defined, and if - * so, it'll edit the dma-ranges property below accordingly. - */ - emmc2bus: emmc2bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - - ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>; - dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>; - - emmc2: mmc@7e340000 { - compatible = "brcm,bcm2711-emmc2"; - reg = <0x0 0x7e340000 0x100>; - interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clocks BCM2711_CLOCK_EMMC2>; - status = "disabled"; - }; - }; - - arm-pmu { - compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3"; - interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; - interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; - }; - - timer { - compatible = "arm,armv8-timer"; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | - IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | - IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | - IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | - IRQ_TYPE_LEVEL_LOW)>; - /* This only applies to the ARMv7 stub */ - arm,cpu-registers-not-fw-configured; - }; - - cpus: cpus { - #address-cells = <1>; - #size-cells = <0>; - enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit - - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a72"; - reg = <0>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000d8>; - }; - - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a72"; - reg = <1>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000e0>; - }; - - cpu2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a72"; - reg = <2>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000e8>; - }; - - cpu3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a72"; - reg = <3>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000f0>; - }; - }; - - scb { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - - ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, - <0x6 0x00000000 0x6 0x00000000 0x40000000>; - - pcie0: pcie@7d500000 { - compatible = "brcm,bcm2711-pcie"; - reg = <0x0 0x7d500000 0x9310>; - device_type = "pci"; - #address-cells = <3>; - #interrupt-cells = <1>; - #size-cells = <2>; - interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "pcie", "msi"; - interrupt-map-mask = <0x0 0x0 0x0 0x7>; - interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 - IRQ_TYPE_LEVEL_HIGH>; - msi-controller; - msi-parent = <&pcie0>; - - ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 - 0x0 0x04000000>; - /* - * The wrapper around the PCIe block has a bug - * preventing it from accessing beyond the first 3GB of - * memory. - */ - dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 - 0x0 0xc0000000>; - brcm,enable-ssc; - }; - - genet: ethernet@7d580000 { - compatible = "brcm,bcm2711-genet-v5"; - reg = <0x0 0x7d580000 0x10000>; - #address-cells = <0x1>; - #size-cells = <0x1>; - interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - - genet_mdio: mdio@e14 { - compatible = "brcm,genet-mdio-v5"; - reg = <0xe14 0x8>; - reg-names = "mdio"; - #address-cells = <0x1>; - #size-cells = <0x0>; - }; - }; - }; -}; - -&clk_osc { - clock-frequency = <54000000>; -}; - -&clocks { - compatible = "brcm,bcm2711-cprman"; -}; - -&cpu_thermal { - coefficients = <(-487) 410040>; - thermal-sensors = <&thermal>; -}; - -&dsi0 { - interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; -}; - -&dsi1 { - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - compatible = "brcm,bcm2711-dsi1"; -}; - -&gpio { - compatible = "brcm,bcm2711-gpio"; - interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; - - gpclk0_gpio49: gpclk0_gpio49 { - pin-gpclk { - pins = "gpio49"; - function = "alt1"; - bias-disable; - }; - }; - gpclk1_gpio50: gpclk1_gpio50 { - pin-gpclk { - pins = "gpio50"; - function = "alt1"; - bias-disable; - }; - }; - gpclk2_gpio51: gpclk2_gpio51 { - pin-gpclk { - pins = "gpio51"; - function = "alt1"; - bias-disable; - }; - }; - - i2c0_gpio46: i2c0_gpio46 { - pin-sda { - function = "alt0"; - pins = "gpio46"; - bias-pull-up; - }; - pin-scl { - function = "alt0"; - pins = "gpio47"; - bias-disable; - }; - }; - i2c1_gpio46: i2c1_gpio46 { - pin-sda { - function = "alt1"; - pins = "gpio46"; - bias-pull-up; - }; - pin-scl { - function = "alt1"; - pins = "gpio47"; - bias-disable; - }; - }; - i2c3_gpio2: i2c3_gpio2 { - pin-sda { - function = "alt5"; - pins = "gpio2"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio3"; - bias-disable; - }; - }; - i2c3_gpio4: i2c3_gpio4 { - pin-sda { - function = "alt5"; - pins = "gpio4"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio5"; - bias-disable; - }; - }; - i2c4_gpio6: i2c4_gpio6 { - pin-sda { - function = "alt5"; - pins = "gpio6"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio7"; - bias-disable; - }; - }; - i2c4_gpio8: i2c4_gpio8 { - pin-sda { - function = "alt5"; - pins = "gpio8"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio9"; - bias-disable; - }; - }; - i2c5_gpio10: i2c5_gpio10 { - pin-sda { - function = "alt5"; - pins = "gpio10"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio11"; - bias-disable; - }; - }; - i2c5_gpio12: i2c5_gpio12 { - pin-sda { - function = "alt5"; - pins = "gpio12"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio13"; - bias-disable; - }; - }; - i2c6_gpio0: i2c6_gpio0 { - pin-sda { - function = "alt5"; - pins = "gpio0"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio1"; - bias-disable; - }; - }; - i2c6_gpio22: i2c6_gpio22 { - pin-sda { - function = "alt5"; - pins = "gpio22"; - bias-pull-up; - }; - pin-scl { - function = "alt5"; - pins = "gpio23"; - bias-disable; - }; - }; - i2c_slave_gpio8: i2c_slave_gpio8 { - pins-i2c-slave { - pins = "gpio8", - "gpio9", - "gpio10", - "gpio11"; - function = "alt3"; - }; - }; - - jtag_gpio48: jtag_gpio48 { - pins-jtag { - pins = "gpio48", - "gpio49", - "gpio50", - "gpio51", - "gpio52", - "gpio53"; - function = "alt4"; - }; - }; - - mii_gpio28: mii_gpio28 { - pins-mii { - pins = "gpio28", - "gpio29", - "gpio30", - "gpio31"; - function = "alt4"; - }; - }; - mii_gpio36: mii_gpio36 { - pins-mii { - pins = "gpio36", - "gpio37", - "gpio38", - "gpio39"; - function = "alt5"; - }; - }; - - pcm_gpio50: pcm_gpio50 { - pins-pcm { - pins = "gpio50", - "gpio51", - "gpio52", - "gpio53"; - function = "alt2"; - }; - }; - - pwm0_0_gpio12: pwm0_0_gpio12 { - pin-pwm { - pins = "gpio12"; - function = "alt0"; - bias-disable; - }; - }; - pwm0_0_gpio18: pwm0_0_gpio18 { - pin-pwm { - pins = "gpio18"; - function = "alt5"; - bias-disable; - }; - }; - pwm1_0_gpio40: pwm1_0_gpio40 { - pin-pwm { - pins = "gpio40"; - function = "alt0"; - bias-disable; - }; - }; - pwm0_1_gpio13: pwm0_1_gpio13 { - pin-pwm { - pins = "gpio13"; - function = "alt0"; - bias-disable; - }; - }; - pwm0_1_gpio19: pwm0_1_gpio19 { - pin-pwm { - pins = "gpio19"; - function = "alt5"; - bias-disable; - }; - }; - pwm1_1_gpio41: pwm1_1_gpio41 { - pin-pwm { - pins = "gpio41"; - function = "alt0"; - bias-disable; - }; - }; - pwm0_1_gpio45: pwm0_1_gpio45 { - pin-pwm { - pins = "gpio45"; - function = "alt0"; - bias-disable; - }; - }; - pwm0_0_gpio52: pwm0_0_gpio52 { - pin-pwm { - pins = "gpio52"; - function = "alt1"; - bias-disable; - }; - }; - pwm0_1_gpio53: pwm0_1_gpio53 { - pin-pwm { - pins = "gpio53"; - function = "alt1"; - bias-disable; - }; - }; - - rgmii_gpio35: rgmii_gpio35 { - pin-start-stop { - pins = "gpio35"; - function = "alt4"; - }; - pin-rx-ok { - pins = "gpio36"; - function = "alt4"; - }; - }; - rgmii_irq_gpio34: rgmii_irq_gpio34 { - pin-irq { - pins = "gpio34"; - function = "alt5"; - }; - }; - rgmii_irq_gpio39: rgmii_irq_gpio39 { - pin-irq { - pins = "gpio39"; - function = "alt4"; - }; - }; - rgmii_mdio_gpio28: rgmii_mdio_gpio28 { - pins-mdio { - pins = "gpio28", - "gpio29"; - function = "alt5"; - }; - }; - rgmii_mdio_gpio37: rgmii_mdio_gpio37 { - pins-mdio { - pins = "gpio37", - "gpio38"; - function = "alt4"; - }; - }; - - spi0_gpio46: spi0_gpio46 { - pins-spi { - pins = "gpio46", - "gpio47", - "gpio48", - "gpio49"; - function = "alt2"; - }; - }; - spi2_gpio46: spi2_gpio46 { - pins-spi { - pins = "gpio46", - "gpio47", - "gpio48", - "gpio49", - "gpio50"; - function = "alt5"; - }; - }; - spi3_gpio0: spi3_gpio0 { - pins-spi { - pins = "gpio0", - "gpio1", - "gpio2", - "gpio3"; - function = "alt3"; - }; - }; - spi4_gpio4: spi4_gpio4 { - pins-spi { - pins = "gpio4", - "gpio5", - "gpio6", - "gpio7"; - function = "alt3"; - }; - }; - spi5_gpio12: spi5_gpio12 { - pins-spi { - pins = "gpio12", - "gpio13", - "gpio14", - "gpio15"; - function = "alt3"; - }; - }; - spi6_gpio18: spi6_gpio18 { - pins-spi { - pins = "gpio18", - "gpio19", - "gpio20", - "gpio21"; - function = "alt3"; - }; - }; - - uart2_gpio0: uart2_gpio0 { - pin-tx { - pins = "gpio0"; - function = "alt4"; - bias-disable; - }; - pin-rx { - pins = "gpio1"; - function = "alt4"; - bias-pull-up; - }; - }; - uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 { - pin-cts { - pins = "gpio2"; - function = "alt4"; - bias-pull-up; - }; - pin-rts { - pins = "gpio3"; - function = "alt4"; - bias-disable; - }; - }; - uart3_gpio4: uart3_gpio4 { - pin-tx { - pins = "gpio4"; - function = "alt4"; - bias-disable; - }; - pin-rx { - pins = "gpio5"; - function = "alt4"; - bias-pull-up; - }; - }; - uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 { - pin-cts { - pins = "gpio6"; - function = "alt4"; - bias-pull-up; - }; - pin-rts { - pins = "gpio7"; - function = "alt4"; - bias-disable; - }; - }; - uart4_gpio8: uart4_gpio8 { - pin-tx { - pins = "gpio8"; - function = "alt4"; - bias-disable; - }; - pin-rx { - pins = "gpio9"; - function = "alt4"; - bias-pull-up; - }; - }; - uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 { - pin-cts { - pins = "gpio10"; - function = "alt4"; - bias-pull-up; - }; - pin-rts { - pins = "gpio11"; - function = "alt4"; - bias-disable; - }; - }; - uart5_gpio12: uart5_gpio12 { - pin-tx { - pins = "gpio12"; - function = "alt4"; - bias-disable; - }; - pin-rx { - pins = "gpio13"; - function = "alt4"; - bias-pull-up; - }; - }; - uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 { - pin-cts { - pins = "gpio14"; - function = "alt4"; - bias-pull-up; - }; - pin-rts { - pins = "gpio15"; - function = "alt4"; - bias-disable; - }; - }; -}; - -&rmem { - #address-cells = <2>; -}; - -&cma { - /* - * arm64 reserves the CMA by default somewhere in ZONE_DMA32, - * that's not good enough for the BCM2711 as some devices can - * only address the lower 1G of memory (ZONE_DMA). - */ - alloc-ranges = <0x0 0x00000000 0x40000000>; -}; - -&i2c0 { - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; -}; - -&i2c1 { - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; -}; - -&mailbox { - interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; -}; - -&sdhci { - interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; -}; - -&sdhost { - interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; -}; - -&spi { - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; -}; - -&spi1 { - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; -}; - -&spi2 { - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; -}; - -&system_timer { - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; -}; - -&txp { - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; -}; - -&uart0 { - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; -}; - -&uart1 { - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; -}; - -&usb { - interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; -}; - -&vec { - compatible = "brcm,bcm2711-vec"; - interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/arch/arm/dts/bcm2835-common.dtsi b/arch/arm/dts/bcm2835-common.dtsi deleted file mode 100644 index c25e797b9060..000000000000 --- a/arch/arm/dts/bcm2835-common.dtsi +++ /dev/null @@ -1,207 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 - -/* This include file covers the common peripherals and configuration between - * bcm2835, bcm2836 and bcm2837 implementations. - */ - -/ { - interrupt-parent = <&intc>; - - soc { - dma: dma@7e007000 { - compatible = "brcm,bcm2835-dma"; - reg = <0x7e007000 0xf00>; - interrupts = <1 16>, - <1 17>, - <1 18>, - <1 19>, - <1 20>, - <1 21>, - <1 22>, - <1 23>, - <1 24>, - <1 25>, - <1 26>, - /* dma channel 11-14 share one irq */ - <1 27>, - <1 27>, - <1 27>, - <1 27>, - /* unused shared irq for all channels */ - <1 28>; - interrupt-names = "dma0", - "dma1", - "dma2", - "dma3", - "dma4", - "dma5", - "dma6", - "dma7", - "dma8", - "dma9", - "dma10", - "dma11", - "dma12", - "dma13", - "dma14", - "dma-shared-all"; - #dma-cells = <1>; - brcm,dma-channel-mask = <0x7f35>; - }; - - intc: interrupt-controller@7e00b200 { - compatible = "brcm,bcm2835-armctrl-ic"; - reg = <0x7e00b200 0x200>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - pm: watchdog@7e100000 { - compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; - #power-domain-cells = <1>; - #reset-cells = <1>; - reg = <0x7e100000 0x114>, - <0x7e00a000 0x24>; - clocks = <&clocks BCM2835_CLOCK_V3D>, - <&clocks BCM2835_CLOCK_PERI_IMAGE>, - <&clocks BCM2835_CLOCK_H264>, - <&clocks BCM2835_CLOCK_ISP>; - clock-names = "v3d", "peri_image", "h264", "isp"; - system-power-controller; - }; - - rng@7e104000 { - compatible = "brcm,bcm2835-rng"; - reg = <0x7e104000 0x10>; - interrupts = <2 29>; - }; - - pixelvalve@7e206000 { - compatible = "brcm,bcm2835-pixelvalve0"; - reg = <0x7e206000 0x100>; - interrupts = <2 13>; /* pwa0 */ - }; - - pixelvalve@7e207000 { - compatible = "brcm,bcm2835-pixelvalve1"; - reg = <0x7e207000 0x100>; - interrupts = <2 14>; /* pwa1 */ - }; - - thermal: thermal@7e212000 { - compatible = "brcm,bcm2835-thermal"; - reg = <0x7e212000 0x8>; - clocks = <&clocks BCM2835_CLOCK_TSENS>; - #thermal-sensor-cells = <0>; - status = "disabled"; - }; - - i2c2: i2c@7e805000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e805000 0x1000>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - }; - - vec: vec@7e806000 { - compatible = "brcm,bcm2835-vec"; - reg = <0x7e806000 0x1000>; - clocks = <&clocks BCM2835_CLOCK_VEC>; - interrupts = <2 27>; - status = "disabled"; - }; - - pixelvalve@7e807000 { - compatible = "brcm,bcm2835-pixelvalve2"; - reg = <0x7e807000 0x100>; - interrupts = <2 10>; /* pixelvalve */ - }; - - hdmi: hdmi@7e902000 { - compatible = "brcm,bcm2835-hdmi"; - reg = <0x7e902000 0x600>, - <0x7e808000 0x100>; - interrupts = <2 8>, <2 9>; - ddc = <&i2c2>; - clocks = <&clocks BCM2835_PLLH_PIX>, - <&clocks BCM2835_CLOCK_HSM>; - clock-names = "pixel", "hdmi"; - dmas = <&dma 17>; - dma-names = "audio-rx"; - status = "disabled"; - }; - - v3d: v3d@7ec00000 { - compatible = "brcm,bcm2835-v3d"; - reg = <0x7ec00000 0x1000>; - interrupts = <1 10>; - }; - - vc4: gpu { - compatible = "brcm,bcm2835-vc4"; - }; - }; -}; - -&cpu_thermal { - thermal-sensors = <&thermal>; -}; - -&gpio { - i2c_slave_gpio18: i2c_slave_gpio18 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT3>; - }; - - jtag_gpio4: jtag_gpio4 { - brcm,pins = <4 5 6 12 13>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - - pwm0_gpio12: pwm0_gpio12 { - brcm,pins = <12>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm0_gpio18: pwm0_gpio18 { - brcm,pins = <18>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - pwm0_gpio40: pwm0_gpio40 { - brcm,pins = <40>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm1_gpio13: pwm1_gpio13 { - brcm,pins = <13>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm1_gpio19: pwm1_gpio19 { - brcm,pins = <19>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - pwm1_gpio41: pwm1_gpio41 { - brcm,pins = <41>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm1_gpio45: pwm1_gpio45 { - brcm,pins = <45>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; -}; - -&i2s { - dmas = <&dma 2>, <&dma 3>; - dma-names = "tx", "rx"; -}; - -&sdhost { - dmas = <&dma 13>; - dma-names = "rx-tx"; -}; - -&spi { - dmas = <&dma 6>, <&dma 7>; - dma-names = "tx", "rx"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts deleted file mode 100644 index 40b9405f1a8e..000000000000 --- a/arch/arm/dts/bcm2835-rpi-a-plus.dts +++ /dev/null @@ -1,128 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,model-a-plus", "brcm,bcm2835"; - model = "Raspberry Pi Model A+"; - - memory@0 { - device_type = "memory"; - reg = <0 0x10000000>; - }; - - leds { - led-act { - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; - }; - - led-pwr { - label = "PWR"; - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - linux,default-trigger = "default-on"; - }; - }; -}; - -&gpio { - /* - * This is based on the unreleased schematic for the Model A+. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD0", - "RXD0", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "SDA0", - "SCL0", - "NC", /* GPIO30 */ - "NC", /* GPIO31 */ - "CAM_GPIO1", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "PWR_LOW_N", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "USB_LIMIT", /* GPIO38 */ - "NC", /* GPIO39 */ - "PWM0_OUT", /* GPIO40 */ - "CAM_GPIO0", /* GPIO41 */ - "NC", /* GPIO42 */ - "NC", /* GPIO43 */ - "NC", /* GPIO44 */ - "PWM1_OUT", /* GPIO45 */ - "HDMI_HPD_N", - "STATUS_LED", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; - - /* I2S interface */ - i2s_alt0: i2s_alt0 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts deleted file mode 100644 index 11edb581dbaf..000000000000 --- a/arch/arm/dts/bcm2835-rpi-a.dts +++ /dev/null @@ -1,123 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,model-a", "brcm,bcm2835"; - model = "Raspberry Pi Model A"; - - memory@0 { - device_type = "memory"; - reg = <0 0x10000000>; - }; - - leds { - led-act { - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - /* - * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf - * RPI00021 sheet 02 - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "SDA0", - "SCL0", - "SDA1", - "SCL1", - "GPIO_GCLK", - "CAM_GPIO1", - "LAN_RUN", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "NC", /* GPIO12 */ - "NC", /* GPIO13 */ - /* Serial port */ - "TXD0", - "RXD0", - "STATUS_LED_N", - "GPIO17", - "GPIO18", - "NC", /* GPIO19 */ - "NC", /* GPIO20 */ - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "NC", /* GPIO26 */ - "CAM_GPIO0", - /* Binary number representing build/revision */ - "CONFIG0", - "CONFIG1", - "CONFIG2", - "CONFIG3", - "NC", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "NC", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "NC", /* GPIO38 */ - "NC", /* GPIO39 */ - "PWM0_OUT", - "NC", /* GPIO41 */ - "NC", /* GPIO42 */ - "NC", /* GPIO43 */ - "NC", /* GPIO44 */ - "PWM1_OUT", - "HDMI_HPD_P", - "SD_CARD_DET", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; - - /* I2S interface */ - i2s_alt2: i2s_alt2 { - brcm,pins = <28 29 30 31>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts deleted file mode 100644 index 1b435c64bd9c..000000000000 --- a/arch/arm/dts/bcm2835-rpi-b-plus.dts +++ /dev/null @@ -1,130 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-smsc9514.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; - model = "Raspberry Pi Model B+"; - - memory@0 { - device_type = "memory"; - reg = <0 0x20000000>; - }; - - leds { - led-act { - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; - }; - - led-pwr { - label = "PWR"; - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - linux,default-trigger = "default-on"; - }; - }; -}; - -&gpio { - /* - * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf - * RPI-BPLUS sheet 1 - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD0", - "RXD0", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "SDA0", - "SCL0", - "NC", /* GPIO30 */ - "LAN_RUN", /* GPIO31 */ - "CAM_GPIO1", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "PWR_LOW_N", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "USB_LIMIT", /* GPIO38 */ - "NC", /* GPIO39 */ - "PWM0_OUT", /* GPIO40 */ - "CAM_GPIO0", /* GPIO41 */ - "NC", /* GPIO42 */ - "NC", /* GPIO43 */ - "ETHCLK", /* GPIO44 */ - "PWM1_OUT", /* GPIO45 */ - "HDMI_HPD_N", - "STATUS_LED", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; - - /* I2S interface */ - i2s_alt0: i2s_alt0 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts deleted file mode 100644 index a23c25c00eea..000000000000 --- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts +++ /dev/null @@ -1,123 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-smsc9512.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; - model = "Raspberry Pi Model B rev2"; - - memory@0 { - device_type = "memory"; - reg = <0 0x10000000>; - }; - - leds { - led-act { - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - /* - * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf - * RPI00022 sheet 02 - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "SDA0", - "SCL0", - "SDA1", - "SCL1", - "GPIO_GCLK", - "CAM_CLK", - "LAN_RUN", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "NC", /* GPIO12 */ - "NC", /* GPIO13 */ - /* Serial port */ - "TXD0", - "RXD0", - "STATUS_LED_N", - "GPIO17", - "GPIO18", - "NC", /* GPIO19 */ - "NC", /* GPIO20 */ - "CAM_GPIO", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "NC", /* GPIO26 */ - "GPIO27", - "GPIO28", - "GPIO29", - "GPIO30", - "GPIO31", - "NC", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "NC", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "NC", /* GPIO38 */ - "NC", /* GPIO39 */ - "PWM0_OUT", - "NC", /* GPIO41 */ - "NC", /* GPIO42 */ - "NC", /* GPIO43 */ - "NC", /* GPIO44 */ - "PWM1_OUT", - "HDMI_HPD_P", - "SD_CARD_DET", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; - - /* I2S interface */ - i2s_alt2: i2s_alt2 { - brcm,pins = <28 29 30 31>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts deleted file mode 100644 index 1b63d6b19750..000000000000 --- a/arch/arm/dts/bcm2835-rpi-b.dts +++ /dev/null @@ -1,118 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-smsc9512.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,model-b", "brcm,bcm2835"; - model = "Raspberry Pi Model B"; - - memory@0 { - device_type = "memory"; - reg = <0 0x10000000>; - }; - - leds { - led-act { - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - /* - * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf - * RPI00021 sheet 02 - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "SDA0", - "SCL0", - "SDA1", - "SCL1", - "GPIO_GCLK", - "CAM_GPIO1", - "LAN_RUN", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "NC", /* GPIO12 */ - "NC", /* GPIO13 */ - /* Serial port */ - "TXD0", - "RXD0", - "STATUS_LED_N", - "GPIO17", - "GPIO18", - "NC", /* GPIO19 */ - "NC", /* GPIO20 */ - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "NC", /* GPIO26 */ - "CAM_GPIO0", - /* Binary number representing build/revision */ - "CONFIG0", - "CONFIG1", - "CONFIG2", - "CONFIG3", - "NC", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "NC", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "NC", /* GPIO38 */ - "NC", /* GPIO39 */ - "PWM0_OUT", - "NC", /* GPIO41 */ - "NC", /* GPIO42 */ - "NC", /* GPIO43 */ - "NC", /* GPIO44 */ - "PWM1_OUT", - "HDMI_HPD_P", - "SD_CARD_DET", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0>; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts deleted file mode 100644 index a75c882e6575..000000000000 --- a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts +++ /dev/null @@ -1,97 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835-rpi-cm1.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,compute-module", "brcm,bcm2835"; - model = "Raspberry Pi Compute Module IO board rev1"; -}; - -&gpio { - /* - * This is based on the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "GPIO0", - "GPIO1", - "GPIO2", - "GPIO3", - "GPIO4", - "GPIO5", - "GPIO6", - "GPIO7", - "GPIO8", - "GPIO9", - "GPIO10", - "GPIO11", - "GPIO12", - "GPIO13", - "GPIO14", - "GPIO15", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "GPIO28", - "GPIO29", - "GPIO30", - "GPIO31", - "GPIO32", - "GPIO33", - "GPIO34", - "GPIO35", - "GPIO36", - "GPIO37", - "GPIO38", - "GPIO39", - "GPIO40", - "GPIO41", - "GPIO42", - "GPIO43", - "GPIO44", - "GPIO45", - "HDMI_HPD_N", - /* Also used as ACT LED */ - "EMMC_EN_N", - /* Used by eMMC */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0>; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/dts/bcm2835-rpi-cm1.dtsi deleted file mode 100644 index e4e6b6abbfc1..000000000000 --- a/arch/arm/dts/bcm2835-rpi-cm1.dtsi +++ /dev/null @@ -1,39 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" - -/ { - leds { - led-act { - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; - }; - }; - - memory@0 { - device_type = "memory"; - reg = <0 0x20000000>; - }; - - reg_3v3: fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - reg_1v8: fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; -}; - -&sdhost { - non-removable; - vmmc-supply = <®_3v3>; - vqmmc-supply = <®_1v8>; -}; diff --git a/arch/arm/dts/bcm2835-rpi-common.dtsi b/arch/arm/dts/bcm2835-rpi-common.dtsi deleted file mode 100644 index 8a55b6cded59..000000000000 --- a/arch/arm/dts/bcm2835-rpi-common.dtsi +++ /dev/null @@ -1,12 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * This include file covers the common peripherals and configuration between - * bcm2835, bcm2836 and bcm2837 implementations that interact with RPi's - * firmware interface. - */ - -#include <dt-bindings/power/raspberrypi-power.h> - -&v3d { - power-domains = <&power RPI_POWER_DOMAIN_V3D>; -}; diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts deleted file mode 100644 index 33b2b77aa47d..000000000000 --- a/arch/arm/dts/bcm2835-rpi-zero-w.dts +++ /dev/null @@ -1,151 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com> - */ - -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-usb-otg.dtsi" - -/ { - compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; - model = "Raspberry Pi Zero W"; - - memory@0 { - device_type = "memory"; - reg = <0 0x20000000>; - }; - - chosen { - /* 8250 auxiliary UART instead of pl011 */ - stdout-path = "serial1:115200n8"; - }; - - leds { - led-act { - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; - }; - }; - - wifi_pwrseq: wifi-pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>; - }; -}; - -&gpio { - /* - * This is based on the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD0", - "RXD0", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "SDA0", - "SCL0", - "NC", /* GPIO30 */ - "NC", /* GPIO31 */ - "NC", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "NC", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "NC", /* GPIO38 */ - "NC", /* GPIO39 */ - "CAM_GPIO1", /* GPIO40 */ - "WL_ON", /* GPIO41 */ - "NC", /* GPIO42 */ - "WIFI_CLK", /* GPIO43 */ - "CAM_GPIO0", /* GPIO44 */ - "BT_ON", /* GPIO45 */ - "HDMI_HPD_N", - "STATUS_LED_N", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0>; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&sdhci { - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>; - bus-width = <4>; - mmc-pwrseq = <&wifi_pwrseq>; - non-removable; - status = "okay"; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <2000000>; - shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; - }; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi-zero.dts b/arch/arm/dts/bcm2835-rpi-zero.dts deleted file mode 100644 index 6f9b3a908f28..000000000000 --- a/arch/arm/dts/bcm2835-rpi-zero.dts +++ /dev/null @@ -1,119 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com> - */ - -/dts-v1/; -#include "bcm2835.dtsi" -#include "bcm2835-rpi.dtsi" -#include "bcm283x-rpi-usb-otg.dtsi" - -/ { - compatible = "raspberrypi,model-zero", "brcm,bcm2835"; - model = "Raspberry Pi Zero"; - - memory@0 { - device_type = "memory"; - reg = <0 0x20000000>; - }; - - leds { - led-act { - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&gpio { - /* - * This is based on the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD0", - "RXD0", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "SDA0", - "SCL0", - "NC", /* GPIO30 */ - "NC", /* GPIO31 */ - "CAM_GPIO1", /* GPIO32 */ - "NC", /* GPIO33 */ - "NC", /* GPIO34 */ - "NC", /* GPIO35 */ - "NC", /* GPIO36 */ - "NC", /* GPIO37 */ - "NC", /* GPIO38 */ - "NC", /* GPIO39 */ - "NC", /* GPIO40 */ - "CAM_GPIO0", /* GPIO41 */ - "NC", /* GPIO42 */ - "NC", /* GPIO43 */ - "NC", /* GPIO44 */ - "NC", /* GPIO45 */ - "HDMI_HPD_N", - "STATUS_LED_N", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; - - /* I2S interface */ - i2s_alt0: i2s_alt0 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi deleted file mode 100644 index 87ddcad76083..000000000000 --- a/arch/arm/dts/bcm2835-rpi.dtsi +++ /dev/null @@ -1,81 +0,0 @@ -#include <dt-bindings/power/raspberrypi-power.h> - -/ { - leds { - compatible = "gpio-leds"; - - led-act { - label = "ACT"; - default-state = "keep"; - linux,default-trigger = "heartbeat"; - }; - }; - - soc { - firmware: firmware { - compatible = "raspberrypi,bcm2835-firmware", "simple-mfd"; - #address-cells = <1>; - #size-cells = <1>; - - mboxes = <&mailbox>; - dma-ranges; - }; - - power: power { - compatible = "raspberrypi,bcm2835-power"; - firmware = <&firmware>; - #power-domain-cells = <1>; - }; - - vchiq: mailbox@7e00b840 { - compatible = "brcm,bcm2835-vchiq"; - reg = <0x7e00b840 0x3c>; - interrupts = <0 2>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - - gpioout: gpioout { - brcm,pins = <6>; - brcm,function = <BCM2835_FSEL_GPIO_OUT>; - }; - - alt0: alt0 { - brcm,pins = <4 5 7 8 9 10 11>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_gpio0>; - status = "okay"; - clock-frequency = <100000>; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_gpio2>; - status = "okay"; - clock-frequency = <100000>; -}; - -&usb { - power-domains = <&power RPI_POWER_DOMAIN_USB>; -}; - -&vec { - power-domains = <&power RPI_POWER_DOMAIN_VEC>; - status = "okay"; -}; - -&dsi0 { - power-domains = <&power RPI_POWER_DOMAIN_DSI0>; -}; - -&dsi1 { - power-domains = <&power RPI_POWER_DOMAIN_DSI1>; -}; diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi deleted file mode 100644 index 0549686134ea..000000000000 --- a/arch/arm/dts/bcm2835.dtsi +++ /dev/null @@ -1,38 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "bcm283x.dtsi" -#include "bcm2835-common.dtsi" -#include "bcm2835-rpi-common.dtsi" - -/ { - compatible = "brcm,bcm2835"; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - device_type = "cpu"; - compatible = "arm,arm1176jzf-s"; - reg = <0x0>; - }; - }; - - soc { - ranges = <0x7e000000 0x20000000 0x02000000>; - dma-ranges = <0x40000000 0x00000000 0x20000000>; - }; - - arm-pmu { - compatible = "arm,arm1176-pmu"; - }; -}; - -&cpu_thermal { - coefficients = <(-538) 407000>; -}; - -/* enable thermal sensor with the correct compatible property set */ -&thermal { - compatible = "brcm,bcm2835-thermal"; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts deleted file mode 100644 index d8af8eeac7b6..000000000000 --- a/arch/arm/dts/bcm2836-rpi-2-b.dts +++ /dev/null @@ -1,130 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2836.dtsi" -#include "bcm2836-rpi.dtsi" -#include "bcm283x-rpi-smsc9514.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; - model = "Raspberry Pi 2 Model B"; - - memory@0 { - device_type = "memory"; - reg = <0 0x40000000>; - }; - - leds { - led-act { - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; - }; - - led-pwr { - label = "PWR"; - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - linux,default-trigger = "default-on"; - }; - }; -}; - -&gpio { - /* - * Taken from rpi_SCH_2b_1p2_reduced.pdf and - * the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD0", - "RXD0", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "SDA0", - "SCL0", - "", /* GPIO30 */ - "LAN_RUN", - "CAM_GPIO1", - "", /* GPIO33 */ - "", /* GPIO34 */ - "PWR_LOW_N", - "", /* GPIO36 */ - "", /* GPIO37 */ - "USB_LIMIT", - "", /* GPIO39 */ - "PWM0_OUT", - "CAM_GPIO0", - "SMPS_SCL", - "SMPS_SDA", - "ETHCLK", - "PWM1_OUT", - "HDMI_HPD_N", - "STATUS_LED", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; - - /* I2S interface */ - i2s_alt0: i2s_alt0 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; -}; - -&hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2836-rpi.dtsi b/arch/arm/dts/bcm2836-rpi.dtsi deleted file mode 100644 index c4c858b984c6..000000000000 --- a/arch/arm/dts/bcm2836-rpi.dtsi +++ /dev/null @@ -1,6 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "bcm2835-rpi.dtsi" - -&vchiq { - compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq"; -}; diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi deleted file mode 100644 index b390006aef79..000000000000 --- a/arch/arm/dts/bcm2836.dtsi +++ /dev/null @@ -1,92 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include "bcm283x.dtsi" -#include "bcm2835-common.dtsi" -#include "bcm2835-rpi-common.dtsi" - -/ { - compatible = "brcm,bcm2836"; - - soc { - ranges = <0x7e000000 0x3f000000 0x1000000>, - <0x40000000 0x40000000 0x00001000>; - dma-ranges = <0xc0000000 0x00000000 0x3f000000>; - - local_intc: local_intc@40000000 { - compatible = "brcm,bcm2836-l1-intc"; - reg = <0x40000000 0x100>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&local_intc>; - }; - }; - - arm-pmu { - compatible = "arm,cortex-a7-pmu"; - interrupt-parent = <&local_intc>; - interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; - }; - - timer { - compatible = "arm,armv7-timer"; - interrupt-parent = <&local_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI - <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI - <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI - <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI - always-on; - }; - - cpus: cpus { - #address-cells = <1>; - #size-cells = <0>; - enable-method = "brcm,bcm2836-smp"; - - v7_cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a7"; - reg = <0xf00>; - clock-frequency = <800000000>; - }; - - v7_cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a7"; - reg = <0xf01>; - clock-frequency = <800000000>; - }; - - v7_cpu2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a7"; - reg = <0xf02>; - clock-frequency = <800000000>; - }; - - v7_cpu3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a7"; - reg = <0xf03>; - clock-frequency = <800000000>; - }; - }; -}; - -/* Make the BCM2835-style global interrupt controller be a child of the - * CPU-local interrupt controller. - */ -&intc { - compatible = "brcm,bcm2836-armctrl-ic"; - reg = <0x7e00b200 0x200>; - interrupt-parent = <&local_intc>; - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; -}; - -&cpu_thermal { - coefficients = <(-538) 407000>; -}; - -/* enable thermal sensor with the correct compatible property set */ -&thermal { - compatible = "brcm,bcm2836-thermal"; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts deleted file mode 100644 index 77099a7871b0..000000000000 --- a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts +++ /dev/null @@ -1,180 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2837.dtsi" -#include "bcm2836-rpi.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837"; - model = "Raspberry Pi 3 Model A+"; - - chosen { - /* 8250 auxiliary UART instead of pl011 */ - stdout-path = "serial1:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0 0x20000000>; - }; - - leds { - led-act { - gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; - }; - - led-pwr { - label = "PWR"; - gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - linux,default-trigger = "default-on"; - }; - }; -}; - -&firmware { - expgpio: gpio { - compatible = "raspberrypi,firmware-gpio"; - gpio-controller; - #gpio-cells = <2>; - gpio-line-names = "", - "BT_WL_ON", - "STATUS_LED_R", - "", - "", - "CAM_GPIO0", - "CAM_GPIO1", - ""; - status = "okay"; - }; -}; - -&gpio { - /* - * This is mostly based on the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD1", - "RXD1", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "HDMI_HPD_N", - "STATUS_LED_G", - /* Used by BT module */ - "CTS0", - "RTS0", - "TXD0", - "RXD0", - /* Used by Wifi */ - "SD1_CLK", - "SD1_CMD", - "SD1_DATA0", - "SD1_DATA1", - "SD1_DATA2", - "SD1_DATA3", - "PWM0_OUT", - "PWM1_OUT", - "", /* GPIO42 */ - "WIFI_CLK", - "SDA0", - "SCL0", - "SMPS_SCL", - "SMPS_SDA", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; -}; - -&hdmi { - hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; - status = "okay"; -}; - -/* - * SDHCI is used to control the SDIO for wireless - * - * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven - * by a single GPIO. We can't give GPIO control to one of the drivers, - * otherwise the other part would get unexpectedly disturbed. - */ -&sdhci { - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio34>; - status = "okay"; - bus-width = <4>; - non-removable; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -/* SDHOST is used to drive the SD card */ -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - status = "okay"; - bus-width = <4>; -}; - -/* uart0 communicates with the BT module */ -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <2000000>; - }; -}; - -/* uart1 is mapped to the pin header */ -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts deleted file mode 100644 index 61010266ca9a..000000000000 --- a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts +++ /dev/null @@ -1,183 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2837.dtsi" -#include "bcm2836-rpi.dtsi" -#include "bcm283x-rpi-lan7515.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; - model = "Raspberry Pi 3 Model B+"; - - chosen { - /* 8250 auxiliary UART instead of pl011 */ - stdout-path = "serial1:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0 0x40000000>; - }; - - leds { - led-act { - gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; - }; - - led-pwr { - label = "PWR"; - gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - linux,default-trigger = "default-on"; - }; - }; - - wifi_pwrseq: wifi-pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; - }; -}; - -&firmware { - expgpio: gpio { - compatible = "raspberrypi,firmware-gpio"; - gpio-controller; - #gpio-cells = <2>; - gpio-line-names = "BT_ON", - "WL_ON", - "STATUS_LED_R", - "LAN_RUN", - "", - "CAM_GPIO0", - "CAM_GPIO1", - ""; - status = "okay"; - }; -}; - -&gpio { - /* - * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and - * the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD1", - "RXD1", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "HDMI_HPD_N", - "STATUS_LED_G", - /* Used by BT module */ - "CTS0", - "RTS0", - "TXD0", - "RXD0", - /* Used by Wifi */ - "SD1_CLK", - "SD1_CMD", - "SD1_DATA0", - "SD1_DATA1", - "SD1_DATA2", - "SD1_DATA3", - "PWM0_OUT", - "PWM1_OUT", - "ETHCLK", - "WIFI_CLK", - "SDA0", - "SCL0", - "SMPS_SCL", - "SMPS_SDA", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; -}; - -&hdmi { - hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; - status = "okay"; -}; - -/* SDHCI is used to control the SDIO for wireless */ -&sdhci { - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio34>; - status = "okay"; - bus-width = <4>; - non-removable; - mmc-pwrseq = <&wifi_pwrseq>; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -/* SDHOST is used to drive the SD card */ -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - status = "okay"; - bus-width = <4>; -}; - -/* uart0 communicates with the BT module */ -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <2000000>; - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; - }; -}; - -/* uart1 is mapped to the pin header */ -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts deleted file mode 100644 index dd4a48604097..000000000000 --- a/arch/arm/dts/bcm2837-rpi-3-b.dts +++ /dev/null @@ -1,176 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2837.dtsi" -#include "bcm2836-rpi.dtsi" -#include "bcm283x-rpi-smsc9514.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; - model = "Raspberry Pi 3 Model B"; - - chosen { - /* 8250 auxiliary UART instead of pl011 */ - stdout-path = "serial1:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0 0x40000000>; - }; - - leds { - led-act { - gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>; - }; - }; - - wifi_pwrseq: wifi-pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; - }; -}; - -&firmware { - expgpio: gpio { - compatible = "raspberrypi,firmware-gpio"; - gpio-controller; - #gpio-cells = <2>; - gpio-line-names = "BT_ON", - "WL_ON", - "STATUS_LED", - "LAN_RUN", - "HDMI_HPD_N", - "CAM_GPIO0", - "CAM_GPIO1", - "PWR_LOW_N"; - status = "okay"; - }; -}; - -&gpio { - /* - * Taken from rpi_SCH_3b_1p2_reduced.pdf and - * the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "ID_SDA", - "ID_SCL", - "SDA1", - "SCL1", - "GPIO_GCLK", - "GPIO5", - "GPIO6", - "SPI_CE1_N", - "SPI_CE0_N", - "SPI_MISO", - "SPI_MOSI", - "SPI_SCLK", - "GPIO12", - "GPIO13", - /* Serial port */ - "TXD1", - "RXD1", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "", /* GPIO 28 */ - "LAN_RUN_BOOT", - /* Used by BT module */ - "CTS0", - "RTS0", - "TXD0", - "RXD0", - /* Used by Wifi */ - "SD1_CLK", - "SD1_CMD", - "SD1_DATA0", - "SD1_DATA1", - "SD1_DATA2", - "SD1_DATA3", - "PWM0_OUT", - "PWM1_OUT", - "ETHCLK", - "WIFI_CLK", - "SDA0", - "SCL0", - "SMPS_SCL", - "SMPS_SDA", - /* Used by SD Card */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; - status = "okay"; -}; - -&hdmi { - hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -/* uart0 communicates with the BT module */ -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <2000000>; - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; - }; -}; - -/* uart1 is mapped to the pin header */ -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_gpio14>; - status = "okay"; -}; - -/* SDHCI is used to control the SDIO for wireless */ -&sdhci { - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio34>; - status = "okay"; - bus-width = <4>; - non-removable; - mmc-pwrseq = <&wifi_pwrseq>; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - }; -}; - -/* SDHOST is used to drive the SD card */ -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - status = "okay"; - bus-width = <4>; -}; diff --git a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts deleted file mode 100644 index 588d9411ceb6..000000000000 --- a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts +++ /dev/null @@ -1,96 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2837-rpi-cm3.dtsi" -#include "bcm283x-rpi-usb-host.dtsi" - -/ { - compatible = "raspberrypi,3-compute-module", "brcm,bcm2837"; - model = "Raspberry Pi Compute Module 3 IO board V3.0"; -}; - -&gpio { - /* - * This is based on the official GPU firmware DT blob. - * - * Legend: - * "NC" = not connected (no rail from the SoC) - * "FOO" = GPIO line named "FOO" on the schematic - * "FOO_N" = GPIO line named "FOO" on schematic, active low - */ - gpio-line-names = "GPIO0", - "GPIO1", - "GPIO2", - "GPIO3", - "GPIO4", - "GPIO5", - "GPIO6", - "GPIO7", - "GPIO8", - "GPIO9", - "GPIO10", - "GPIO11", - "GPIO12", - "GPIO13", - "GPIO14", - "GPIO15", - "GPIO16", - "GPIO17", - "GPIO18", - "GPIO19", - "GPIO20", - "GPIO21", - "GPIO22", - "GPIO23", - "GPIO24", - "GPIO25", - "GPIO26", - "GPIO27", - "GPIO28", - "GPIO29", - "GPIO30", - "GPIO31", - "GPIO32", - "GPIO33", - "GPIO34", - "GPIO35", - "GPIO36", - "GPIO37", - "GPIO38", - "GPIO39", - "GPIO40", - "GPIO41", - "GPIO42", - "GPIO43", - "GPIO44", - "GPIO45", - "GPIO46", - "GPIO47", - /* Used by eMMC */ - "SD_CLK_R", - "SD_CMD_R", - "SD_DATA0_R", - "SD_DATA1_R", - "SD_DATA2_R", - "SD_DATA3_R"; - - pinctrl-0 = <&gpioout &alt0>; -}; - -&hdmi { - hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_gpio14>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/dts/bcm2837-rpi-cm3.dtsi deleted file mode 100644 index 828a20561b96..000000000000 --- a/arch/arm/dts/bcm2837-rpi-cm3.dtsi +++ /dev/null @@ -1,61 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/dts-v1/; -#include "bcm2837.dtsi" -#include "bcm2836-rpi.dtsi" - -/ { - memory@0 { - device_type = "memory"; - reg = <0 0x40000000>; - }; - - leds { - /* - * Since there is no upstream GPIO driver yet, - * remove the incomplete node. - */ - /delete-node/ led-act; - }; - - reg_3v3: fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - reg_1v8: fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; -}; - -&firmware { - expgpio: gpio { - compatible = "raspberrypi,firmware-gpio"; - gpio-controller; - #gpio-cells = <2>; - gpio-line-names = "HDMI_HPD_N", - "EMMC_EN_N", - "NC", - "NC", - "NC", - "NC", - "NC", - "NC"; - status = "okay"; - }; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - bus-width = <4>; - vmmc-supply = <®_3v3>; - vqmmc-supply = <®_1v8>; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi deleted file mode 100644 index 0199ec98cd61..000000000000 --- a/arch/arm/dts/bcm2837.dtsi +++ /dev/null @@ -1,95 +0,0 @@ -#include "bcm283x.dtsi" -#include "bcm2835-common.dtsi" -#include "bcm2835-rpi-common.dtsi" - -/ { - compatible = "brcm,bcm2837"; - - soc { - ranges = <0x7e000000 0x3f000000 0x1000000>, - <0x40000000 0x40000000 0x00001000>; - dma-ranges = <0xc0000000 0x00000000 0x3f000000>; - - local_intc: local_intc@40000000 { - compatible = "brcm,bcm2836-l1-intc"; - reg = <0x40000000 0x100>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&local_intc>; - }; - }; - - arm-pmu { - compatible = "arm,cortex-a53-pmu"; - interrupt-parent = <&local_intc>; - interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; - }; - - timer { - compatible = "arm,armv7-timer"; - interrupt-parent = <&local_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI - <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI - <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI - <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI - always-on; - }; - - cpus: cpus { - #address-cells = <1>; - #size-cells = <0>; - enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit - - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000d8>; - }; - - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <1>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000e0>; - }; - - cpu2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <2>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000e8>; - }; - - cpu3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <3>; - enable-method = "spin-table"; - cpu-release-addr = <0x0 0x000000f0>; - }; - }; -}; - -/* Make the BCM2835-style global interrupt controller be a child of the - * CPU-local interrupt controller. - */ -&intc { - compatible = "brcm,bcm2836-armctrl-ic"; - reg = <0x7e00b200 0x200>; - interrupt-parent = <&local_intc>; - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; -}; - -&cpu_thermal { - coefficients = <(-538) 412000>; -}; - -/* enable thermal sensor with the correct compatible property set */ -&thermal { - compatible = "brcm,bcm2837-thermal"; - status = "okay"; -}; diff --git a/arch/arm/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/dts/bcm283x-rpi-lan7515.dtsi deleted file mode 100644 index 70bece63f9a7..000000000000 --- a/arch/arm/dts/bcm283x-rpi-lan7515.dtsi +++ /dev/null @@ -1,41 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -#include <dt-bindings/net/microchip-lan78xx.h> - -/ { - aliases { - ethernet0 = ðernet; - }; -}; - -&usb { - usb-port@1 { - compatible = "usb424,2514"; - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - - usb-port@1 { - compatible = "usb424,2514"; - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - - ethernet: ethernet@1 { - compatible = "usb424,7800"; - reg = <1>; - - mdio { - #address-cells = <0x1>; - #size-cells = <0x0>; - eth_phy: ethernet-phy@1 { - reg = <1>; - microchip,led-modes = < - LAN78XX_LINK_1000_ACTIVITY - LAN78XX_LINK_10_100_ACTIVITY - >; - }; - }; - }; - }; - }; -}; diff --git a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi deleted file mode 100644 index 967e081cb9c2..000000000000 --- a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi +++ /dev/null @@ -1,20 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/ { - aliases { - ethernet0 = ðernet; - }; -}; - -&usb { - usb1@1 { - compatible = "usb424,9512"; - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - - ethernet: usbether@1 { - compatible = "usb424,ec00"; - reg = <1>; - }; - }; -}; diff --git a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi deleted file mode 100644 index dc7ae776db5f..000000000000 --- a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi +++ /dev/null @@ -1,19 +0,0 @@ -/ { - aliases { - ethernet0 = ðernet; - }; -}; - -&usb { - usb1@1 { - compatible = "usb424,9514"; - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - - ethernet: usbether@1 { - compatible = "usb424,ec00"; - reg = <1>; - }; - }; -}; diff --git a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi deleted file mode 100644 index 73f4ece8dcd0..000000000000 --- a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi +++ /dev/null @@ -1,3 +0,0 @@ -&usb { - dr_mode = "host"; -}; diff --git a/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi b/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi deleted file mode 100644 index e2fd9610e125..000000000000 --- a/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi +++ /dev/null @@ -1,11 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -&usb { - dr_mode = "otg"; - g-rx-fifo-size = <256>; - g-np-tx-fifo-size = <32>; - /* - * According to dwc2 the sum of all device EP - * fifo sizes shouldn't exceed 3776 bytes. - */ - g-tx-fifo-size = <256 256 512 512 512 768 768>; -}; diff --git a/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi deleted file mode 100644 index 0ff0e9e25327..000000000000 --- a/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi +++ /dev/null @@ -1,7 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -&usb { - dr_mode = "peripheral"; - g-rx-fifo-size = <256>; - g-np-tx-fifo-size = <32>; - g-tx-fifo-size = <256 256 512 512 512 768 768>; -}; diff --git a/arch/arm/dts/bcm283x-u-boot.dtsi b/arch/arm/dts/bcm283x-u-boot.dtsi deleted file mode 100644 index ec0f93dd8507..000000000000 --- a/arch/arm/dts/bcm283x-u-boot.dtsi +++ /dev/null @@ -1,29 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * U-Boot addition to keep baudrate set by firmware - * and also initialize before relocation. - * - * (C) Copyright 2016 Fabian Vogt <fvogt@suse.com> - */ - -&uart0 { - skip-init; - bootph-all; -}; - -&uart1 { - skip-init; - bootph-all; -}; - -&gpio { - bootph-all; -}; - -&uart0_gpio14 { - bootph-all; -}; - -&uart1_gpio14 { - bootph-all; -}; diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi deleted file mode 100644 index a3e06b680947..000000000000 --- a/arch/arm/dts/bcm283x.dtsi +++ /dev/null @@ -1,501 +0,0 @@ -#include <dt-bindings/pinctrl/bcm2835.h> -#include <dt-bindings/clock/bcm2835.h> -#include <dt-bindings/clock/bcm2835-aux.h> -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/soc/bcm2835-pm.h> - -/* firmware-provided startup stubs live here, where the secondary CPUs are - * spinning. - */ -/memreserve/ 0x00000000 0x00001000; - -/* This include file covers the common peripherals and configuration between - * bcm2835 and bcm2836 implementations, leaving the CPU configuration to - * bcm2835.dtsi and bcm2836.dtsi. - */ - -/ { - compatible = "brcm,bcm2835"; - model = "BCM2835"; - #address-cells = <1>; - #size-cells = <1>; - - aliases { - serial0 = &uart0; - serial1 = &uart1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - rmem: reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - cma: linux,cma { - compatible = "shared-dma-pool"; - size = <0x4000000>; /* 64MB */ - reusable; - linux,cma-default; - }; - }; - - thermal-zones { - cpu_thermal: cpu-thermal { - polling-delay-passive = <0>; - polling-delay = <1000>; - - trips { - cpu-crit { - temperature = <90000>; - hysteresis = <0>; - type = "critical"; - }; - }; - - cooling-maps { - }; - }; - }; - - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - - system_timer: timer@7e003000 { - compatible = "brcm,bcm2835-system-timer"; - reg = <0x7e003000 0x1000>; - interrupts = <1 0>, <1 1>, <1 2>, <1 3>; - /* This could be a reference to BCM2835_CLOCK_TIMER, - * but we don't have the driver using the common clock - * support yet. - */ - clock-frequency = <1000000>; - }; - - txp: txp@7e004000 { - compatible = "brcm,bcm2835-txp"; - reg = <0x7e004000 0x20>; - interrupts = <1 11>; - }; - - clocks: cprman@7e101000 { - compatible = "brcm,bcm2835-cprman"; - #clock-cells = <1>; - reg = <0x7e101000 0x2000>; - - /* CPRMAN derives almost everything from the - * platform's oscillator. However, the DSI - * pixel clocks come from the DSI analog PHY. - */ - clocks = <&clk_osc>, - <&dsi0 0>, <&dsi0 1>, <&dsi0 2>, - <&dsi1 0>, <&dsi1 1>, <&dsi1 2>; - }; - - mailbox: mailbox@7e00b880 { - compatible = "brcm,bcm2835-mbox"; - reg = <0x7e00b880 0x40>; - interrupts = <0 1>; - #mbox-cells = <0>; - }; - - gpio: gpio@7e200000 { - compatible = "brcm,bcm2835-gpio"; - reg = <0x7e200000 0xb4>; - /* - * The GPIO IP block is designed for 3 banks of GPIOs. - * Each bank has a GPIO interrupt for itself. - * There is an overall "any bank" interrupt. - * In order, these are GIC interrupts 17, 18, 19, 20. - * Since the BCM2835 only has 2 banks, the 2nd bank - * interrupt output appears to be mirrored onto the - * 3rd bank's interrupt signal. - * So, a bank0 interrupt shows up on 17, 20, and - * a bank1 interrupt shows up on 18, 19, 20! - */ - interrupts = <2 17>, <2 18>, <2 19>, <2 20>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - - /* Defines common pin muxing groups - * - * While each pin can have its mux selected - * for various functions individually, some - * groups only make sense to switch to a - * particular function together. - */ - dpi_gpio0: dpi_gpio0 { - brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 - 12 13 14 15 16 17 18 19 - 20 21 22 23 24 25 26 27>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; - emmc_gpio22: emmc_gpio22 { - brcm,pins = <22 23 24 25 26 27>; - brcm,function = <BCM2835_FSEL_ALT3>; - }; - emmc_gpio34: emmc_gpio34 { - brcm,pins = <34 35 36 37 38 39>; - brcm,function = <BCM2835_FSEL_ALT3>; - brcm,pull = <BCM2835_PUD_OFF - BCM2835_PUD_UP - BCM2835_PUD_UP - BCM2835_PUD_UP - BCM2835_PUD_UP - BCM2835_PUD_UP>; - }; - emmc_gpio48: emmc_gpio48 { - brcm,pins = <48 49 50 51 52 53>; - brcm,function = <BCM2835_FSEL_ALT3>; - }; - - gpclk0_gpio4: gpclk0_gpio4 { - brcm,pins = <4>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - gpclk1_gpio5: gpclk1_gpio5 { - brcm,pins = <5>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - gpclk1_gpio42: gpclk1_gpio42 { - brcm,pins = <42>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - gpclk1_gpio44: gpclk1_gpio44 { - brcm,pins = <44>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - gpclk2_gpio6: gpclk2_gpio6 { - brcm,pins = <6>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - gpclk2_gpio43: gpclk2_gpio43 { - brcm,pins = <43>; - brcm,function = <BCM2835_FSEL_ALT0>; - brcm,pull = <BCM2835_PUD_OFF>; - }; - - i2c0_gpio0: i2c0_gpio0 { - brcm,pins = <0 1>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - i2c0_gpio28: i2c0_gpio28 { - brcm,pins = <28 29>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - i2c0_gpio44: i2c0_gpio44 { - brcm,pins = <44 45>; - brcm,function = <BCM2835_FSEL_ALT1>; - }; - i2c1_gpio2: i2c1_gpio2 { - brcm,pins = <2 3>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - i2c1_gpio44: i2c1_gpio44 { - brcm,pins = <44 45>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; - - jtag_gpio22: jtag_gpio22 { - brcm,pins = <22 23 24 25 26 27>; - brcm,function = <BCM2835_FSEL_ALT4>; - }; - - pcm_gpio18: pcm_gpio18 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pcm_gpio28: pcm_gpio28 { - brcm,pins = <28 29 30 31>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; - - sdhost_gpio48: sdhost_gpio48 { - brcm,pins = <48 49 50 51 52 53>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - - spi0_gpio7: spi0_gpio7 { - brcm,pins = <7 8 9 10 11>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - spi0_gpio35: spi0_gpio35 { - brcm,pins = <35 36 37 38 39>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - spi1_gpio16: spi1_gpio16 { - brcm,pins = <16 17 18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT4>; - }; - spi2_gpio40: spi2_gpio40 { - brcm,pins = <40 41 42 43 44 45>; - brcm,function = <BCM2835_FSEL_ALT4>; - }; - - uart0_gpio14: uart0_gpio14 { - brcm,pins = <14 15>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - /* Separate from the uart0_gpio14 group - * because it conflicts with spi1_gpio16, and - * people often run uart0 on the two pins - * without flow control. - */ - uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 { - brcm,pins = <16 17>; - brcm,function = <BCM2835_FSEL_ALT3>; - }; - uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 { - brcm,pins = <30 31>; - brcm,function = <BCM2835_FSEL_ALT3>; - brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>; - }; - uart0_gpio32: uart0_gpio32 { - brcm,pins = <32 33>; - brcm,function = <BCM2835_FSEL_ALT3>; - brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>; - }; - uart0_gpio36: uart0_gpio36 { - brcm,pins = <36 37>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; - uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 { - brcm,pins = <38 39>; - brcm,function = <BCM2835_FSEL_ALT2>; - }; - - uart1_gpio14: uart1_gpio14 { - brcm,pins = <14 15>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 { - brcm,pins = <16 17>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - uart1_gpio32: uart1_gpio32 { - brcm,pins = <32 33>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 { - brcm,pins = <30 31>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - uart1_gpio40: uart1_gpio40 { - brcm,pins = <40 41>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 { - brcm,pins = <42 43>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - }; - - uart0: serial@7e201000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x7e201000 0x200>; - interrupts = <2 25>; - clocks = <&clocks BCM2835_CLOCK_UART>, - <&clocks BCM2835_CLOCK_VPU>; - clock-names = "uartclk", "apb_pclk"; - arm,primecell-periphid = <0x00241011>; - }; - - sdhost: mmc@7e202000 { - compatible = "brcm,bcm2835-sdhost"; - reg = <0x7e202000 0x100>; - interrupts = <2 24>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - status = "disabled"; - }; - - i2s: i2s@7e203000 { - compatible = "brcm,bcm2835-i2s"; - reg = <0x7e203000 0x24>; - clocks = <&clocks BCM2835_CLOCK_PCM>; - status = "disabled"; - }; - - spi: spi@7e204000 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204000 0x200>; - interrupts = <2 22>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c0: i2c@7e205000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e205000 0x200>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - dpi: dpi@7e208000 { - compatible = "brcm,bcm2835-dpi"; - reg = <0x7e208000 0x8c>; - clocks = <&clocks BCM2835_CLOCK_VPU>, - <&clocks BCM2835_CLOCK_DPI>; - clock-names = "core", "pixel"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - dsi0: dsi@7e209000 { - compatible = "brcm,bcm2835-dsi0"; - reg = <0x7e209000 0x78>; - interrupts = <2 4>; - #address-cells = <1>; - #size-cells = <0>; - #clock-cells = <1>; - - clocks = <&clocks BCM2835_PLLA_DSI0>, - <&clocks BCM2835_CLOCK_DSI0E>, - <&clocks BCM2835_CLOCK_DSI0P>; - clock-names = "phy", "escape", "pixel"; - - clock-output-names = "dsi0_byte", - "dsi0_ddr2", - "dsi0_ddr"; - - status = "disabled"; - }; - - aux: aux@7e215000 { - compatible = "brcm,bcm2835-aux"; - #clock-cells = <1>; - reg = <0x7e215000 0x8>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - }; - - uart1: serial@7e215040 { - compatible = "brcm,bcm2835-aux-uart"; - reg = <0x7e215040 0x40>; - interrupts = <1 29>; - clocks = <&aux BCM2835_AUX_CLOCK_UART>; - status = "disabled"; - }; - - spi1: spi@7e215080 { - compatible = "brcm,bcm2835-aux-spi"; - reg = <0x7e215080 0x40>; - interrupts = <1 29>; - clocks = <&aux BCM2835_AUX_CLOCK_SPI1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi2: spi@7e2150c0 { - compatible = "brcm,bcm2835-aux-spi"; - reg = <0x7e2150c0 0x40>; - interrupts = <1 29>; - clocks = <&aux BCM2835_AUX_CLOCK_SPI2>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - pwm: pwm@7e20c000 { - compatible = "brcm,bcm2835-pwm"; - reg = <0x7e20c000 0x28>; - clocks = <&clocks BCM2835_CLOCK_PWM>; - assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; - assigned-clock-rates = <10000000>; - #pwm-cells = <2>; - status = "disabled"; - }; - - sdhci: mmc@7e300000 { - compatible = "brcm,bcm2835-sdhci"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clocks BCM2835_CLOCK_EMMC>; - status = "disabled"; - }; - - hvs@7e400000 { - compatible = "brcm,bcm2835-hvs"; - reg = <0x7e400000 0x6000>; - interrupts = <2 1>; - }; - - dsi1: dsi@7e700000 { - compatible = "brcm,bcm2835-dsi1"; - reg = <0x7e700000 0x8c>; - interrupts = <2 12>; - #address-cells = <1>; - #size-cells = <0>; - #clock-cells = <1>; - - clocks = <&clocks BCM2835_PLLD_DSI1>, - <&clocks BCM2835_CLOCK_DSI1E>, - <&clocks BCM2835_CLOCK_DSI1P>; - clock-names = "phy", "escape", "pixel"; - - clock-output-names = "dsi1_byte", - "dsi1_ddr2", - "dsi1_ddr"; - - status = "disabled"; - }; - - i2c1: i2c@7e804000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e804000 0x1000>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - usb: usb@7e980000 { - compatible = "brcm,bcm2835-usb"; - reg = <0x7e980000 0x10000>; - interrupts = <1 9>; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clk_usb>; - clock-names = "otg"; - phys = <&usbphy>; - phy-names = "usb2-phy"; - }; - }; - - clocks { - /* The oscillator is the root of the clock tree. */ - clk_osc: clk-osc { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-output-names = "osc"; - clock-frequency = <19200000>; - }; - - clk_usb: clk-usb { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-output-names = "otg"; - clock-frequency = <480000000>; - }; - }; - - usbphy: phy { - compatible = "usb-nop-xceiv"; - #phy-cells = <0>; - }; -}; diff --git a/arch/arm/dts/bcm7xxx.dts b/arch/arm/dts/bcm7xxx.dts deleted file mode 100644 index 786ce3ff9597..000000000000 --- a/arch/arm/dts/bcm7xxx.dts +++ /dev/null @@ -1,15 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Empty devicetre file for bcm7260 board - * - * This is required to make the board build with CONFIG OF_SEPARATE - * In-tree document explains how to obtain a real devicetree using 'bolt' but - * I did not attempt this. - * - * Copyright 2021 Google LLC - */ - -/dts-v1/; - -/ { -}; diff --git a/arch/arm/dts/highbank.dts b/arch/arm/dts/highbank.dts deleted file mode 100644 index 1480bad91040..000000000000 --- a/arch/arm/dts/highbank.dts +++ /dev/null @@ -1,9 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Empty devicetree for highbank/midway - */ - -/dts-v1/; - -/ { -}; diff --git a/arch/arm/dts/octeontx.dts b/arch/arm/dts/octeontx.dts deleted file mode 100644 index 60a15f5df23f..000000000000 --- a/arch/arm/dts/octeontx.dts +++ /dev/null @@ -1,14 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Dummy devicetre file for octeontx2 boards - * - * This is required to make the board build with CONFIG OF_SEPARATE - * I could not find any in-tree documentation at all so this is a dummy file. - * - * Copyright 2021 Google LLC - */ - -/dts-v1/; - -/ { -}; diff --git a/arch/arm/dts/qemu-arm.dts b/arch/arm/dts/qemu-arm.dts deleted file mode 100644 index 230c630f04fd..000000000000 --- a/arch/arm/dts/qemu-arm.dts +++ /dev/null @@ -1,11 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ OR MIT -/* - * Empty device tree for qemu_arm - - * Copyright 2021 Google LLC - */ - -/dts-v1/; - -/ { -}; diff --git a/arch/arm/dts/xenguest-arm64.dts b/arch/arm/dts/xenguest-arm64.dts deleted file mode 100644 index d8734433763c..000000000000 --- a/arch/arm/dts/xenguest-arm64.dts +++ /dev/null @@ -1,15 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Empty devicetree file for xenguest_arm64 - * - * This is required to make the board build with CONFIG OF_SEPARATE - * Build instructions at xenguest_arm64.rst are inadequate for obtaining a real - * devicetree. - * - * Copyright 2021 Google LLC - */ - -/dts-v1/; - -/ { -}; -- 2.43.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH v2 5/5] arm: Drop unused dts files 2026-08-24 19:48 ` [PATCH v2 5/5] arm: Drop unused dts files Tom Rini @ 2026-08-24 20:09 ` Peter Robinson 0 siblings, 0 replies; 9+ messages in thread From: Peter Robinson @ 2026-08-24 20:09 UTC (permalink / raw) To: Tom Rini; +Cc: u-boot On Mon, 24 Aug 2026 at 20:53, Tom Rini <trini@konsulko.com> wrote: > > Now that we do not require device tree files to be built when > OF_OMIT_DTB is set, we can remove a number of unused dts files. > > Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> - For RPi DTs > --- > arch/arm/dts/Makefile | 27 +- > arch/arm/dts/arm_fvp.dts | 11 - > arch/arm/dts/bcm2711-rpi-4-b.dts | 262 ----- > arch/arm/dts/bcm2711-rpi.dtsi | 74 -- > arch/arm/dts/bcm2711.dtsi | 1100 ------------------ > arch/arm/dts/bcm2835-common.dtsi | 207 ---- > arch/arm/dts/bcm2835-rpi-a-plus.dts | 128 -- > arch/arm/dts/bcm2835-rpi-a.dts | 123 -- > arch/arm/dts/bcm2835-rpi-b-plus.dts | 130 --- > arch/arm/dts/bcm2835-rpi-b-rev2.dts | 123 -- > arch/arm/dts/bcm2835-rpi-b.dts | 118 -- > arch/arm/dts/bcm2835-rpi-cm1-io1.dts | 97 -- > arch/arm/dts/bcm2835-rpi-cm1.dtsi | 39 - > arch/arm/dts/bcm2835-rpi-common.dtsi | 12 - > arch/arm/dts/bcm2835-rpi-zero-w.dts | 151 --- > arch/arm/dts/bcm2835-rpi-zero.dts | 119 -- > arch/arm/dts/bcm2835-rpi.dtsi | 81 -- > arch/arm/dts/bcm2835.dtsi | 38 - > arch/arm/dts/bcm2836-rpi-2-b.dts | 130 --- > arch/arm/dts/bcm2836-rpi.dtsi | 6 - > arch/arm/dts/bcm2836.dtsi | 92 -- > arch/arm/dts/bcm2837-rpi-3-a-plus.dts | 180 --- > arch/arm/dts/bcm2837-rpi-3-b-plus.dts | 183 --- > arch/arm/dts/bcm2837-rpi-3-b.dts | 176 --- > arch/arm/dts/bcm2837-rpi-cm3-io3.dts | 96 -- > arch/arm/dts/bcm2837-rpi-cm3.dtsi | 61 - > arch/arm/dts/bcm2837.dtsi | 95 -- > arch/arm/dts/bcm283x-rpi-lan7515.dtsi | 41 - > arch/arm/dts/bcm283x-rpi-smsc9512.dtsi | 20 - > arch/arm/dts/bcm283x-rpi-smsc9514.dtsi | 19 - > arch/arm/dts/bcm283x-rpi-usb-host.dtsi | 3 - > arch/arm/dts/bcm283x-rpi-usb-otg.dtsi | 11 - > arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi | 7 - > arch/arm/dts/bcm283x-u-boot.dtsi | 29 - > arch/arm/dts/bcm283x.dtsi | 501 -------- > arch/arm/dts/bcm7xxx.dts | 15 - > arch/arm/dts/highbank.dts | 9 - > arch/arm/dts/octeontx.dts | 14 - > arch/arm/dts/qemu-arm.dts | 11 - > arch/arm/dts/xenguest-arm64.dts | 15 - > 40 files changed, 1 insertion(+), 4553 deletions(-) > delete mode 100644 arch/arm/dts/arm_fvp.dts > delete mode 100644 arch/arm/dts/bcm2711-rpi-4-b.dts > delete mode 100644 arch/arm/dts/bcm2711-rpi.dtsi > delete mode 100644 arch/arm/dts/bcm2711.dtsi > delete mode 100644 arch/arm/dts/bcm2835-common.dtsi > delete mode 100644 arch/arm/dts/bcm2835-rpi-a-plus.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-a.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-b-plus.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-b-rev2.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-b.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-cm1-io1.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-cm1.dtsi > delete mode 100644 arch/arm/dts/bcm2835-rpi-common.dtsi > delete mode 100644 arch/arm/dts/bcm2835-rpi-zero-w.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi-zero.dts > delete mode 100644 arch/arm/dts/bcm2835-rpi.dtsi > delete mode 100644 arch/arm/dts/bcm2835.dtsi > delete mode 100644 arch/arm/dts/bcm2836-rpi-2-b.dts > delete mode 100644 arch/arm/dts/bcm2836-rpi.dtsi > delete mode 100644 arch/arm/dts/bcm2836.dtsi > delete mode 100644 arch/arm/dts/bcm2837-rpi-3-a-plus.dts > delete mode 100644 arch/arm/dts/bcm2837-rpi-3-b-plus.dts > delete mode 100644 arch/arm/dts/bcm2837-rpi-3-b.dts > delete mode 100644 arch/arm/dts/bcm2837-rpi-cm3-io3.dts > delete mode 100644 arch/arm/dts/bcm2837-rpi-cm3.dtsi > delete mode 100644 arch/arm/dts/bcm2837.dtsi > delete mode 100644 arch/arm/dts/bcm283x-rpi-lan7515.dtsi > delete mode 100644 arch/arm/dts/bcm283x-rpi-smsc9512.dtsi > delete mode 100644 arch/arm/dts/bcm283x-rpi-smsc9514.dtsi > delete mode 100644 arch/arm/dts/bcm283x-rpi-usb-host.dtsi > delete mode 100644 arch/arm/dts/bcm283x-rpi-usb-otg.dtsi > delete mode 100644 arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi > delete mode 100644 arch/arm/dts/bcm283x-u-boot.dtsi > delete mode 100644 arch/arm/dts/bcm283x.dtsi > delete mode 100644 arch/arm/dts/bcm7xxx.dts > delete mode 100644 arch/arm/dts/highbank.dts > delete mode 100644 arch/arm/dts/octeontx.dts > delete mode 100644 arch/arm/dts/qemu-arm.dts > delete mode 100644 arch/arm/dts/xenguest-arm64.dts > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 1b533721bb43..782867f3fec3 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -834,8 +834,6 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \ > dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \ > imx7ulp-evk.dtb > > -dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb > - > dtb-$(CONFIG_ARCH_IMX8) += \ > fsl-imx8qm-apalis.dtb \ > fsl-imx8qm-mek.dtb \ > @@ -962,28 +960,10 @@ dtb-$(CONFIG_TARGET_SAMA5D4_XPLAINED) += \ > dtb-$(CONFIG_TARGET_VINCO) += \ > at91-vinco.dtb > > -dtb-$(CONFIG_ARCH_BCM283X) += \ > - bcm2835-rpi-a.dtb \ > - bcm2835-rpi-a-plus.dtb \ > - bcm2835-rpi-b.dtb \ > - bcm2835-rpi-b-plus.dtb \ > - bcm2835-rpi-b-rev2.dtb \ > - bcm2835-rpi-cm1-io1.dtb \ > - bcm2835-rpi-zero.dtb \ > - bcm2835-rpi-zero-w.dtb\ > - bcm2836-rpi-2-b.dtb \ > - bcm2837-rpi-3-a-plus.dtb \ > - bcm2837-rpi-3-b.dtb \ > - bcm2837-rpi-3-b-plus.dtb \ > - bcm2837-rpi-cm3-io3.dtb \ > - bcm2711-rpi-4-b.dtb > - > dtb-$(CONFIG_TARGET_BCMNS) += ns-board.dtb > > dtb-$(CONFIG_TARGET_BCMNS3) += ns3-board.dtb > > -dtb-$(CONFIG_ARCH_BCMSTB) += bcm7xxx.dtb > - > dtb-$(CONFIG_BCM47622) += \ > bcm947622.dtb > dtb-$(CONFIG_BCM4908) += \ > @@ -1099,10 +1079,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ > > dtb-$(CONFIG_ARCH_NPCM7xx) += nuvoton-npcm750-evb.dtb > dtb-$(CONFIG_ARCH_NPCM8XX) += nuvoton-npcm845-evb.dtb > -dtb-$(CONFIG_XEN) += xenguest-arm64.dtb > - > -dtb-$(CONFIG_ARCH_OCTEONTX) += octeontx.dtb > -dtb-$(CONFIG_ARCH_OCTEONTX2) += octeontx.dtb > > dtb-$(CONFIG_TARGET_GE_BX50V3) += \ > imx6q-bx50v3.dtb \ > @@ -1117,7 +1093,6 @@ dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb > # Kconfig option to build all of these. See examples above. > dtb-$(CONFIG_TARGET_VEXPRESS_CA9X4) += vexpress-v2p-ca9.dtb > dtb-$(CONFIG_TARGET_VEXPRESS64_BASE_FVP) += fvp-base-revc.dtb > -dtb-$(CONFIG_TARGET_VEXPRESS64_BASER_FVP) += arm_fvp.dtb > dtb-$(CONFIG_TARGET_VEXPRESS64_JUNO) += juno-r2.dtb > > dtb-$(CONFIG_TARGET_TOTAL_COMPUTE) += total_compute.dtb > @@ -1163,7 +1138,7 @@ endif > > dtb-$(CONFIG_TARGET_EA_LPC3250DEVKITV2) += lpc3250-ea3250.dtb > > -dtb-$(CONFIG_ARCH_QEMU) += qemu-arm.dtb qemu-arm64.dtb > +dtb-$(CONFIG_TARGET_QEMU_ARM_64BIT) += qemu-arm64.dtb > > dtb-$(CONFIG_TARGET_CORSTONE1000) += corstone1000-mps3.dtb \ > corstone1000-fvp.dtb > diff --git a/arch/arm/dts/arm_fvp.dts b/arch/arm/dts/arm_fvp.dts > deleted file mode 100644 > index 3a4ad5d18012..000000000000 > --- a/arch/arm/dts/arm_fvp.dts > +++ /dev/null > @@ -1,11 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ OR MIT > -/* > - * Empty device tree for the Arm Ltd FVP platform model > - > - * Copyright 2022 Arm Ltd. > - */ > - > -/dts-v1/; > - > -/ { > -}; > diff --git a/arch/arm/dts/bcm2711-rpi-4-b.dts b/arch/arm/dts/bcm2711-rpi-4-b.dts > deleted file mode 100644 > index 72ce80fbf266..000000000000 > --- a/arch/arm/dts/bcm2711-rpi-4-b.dts > +++ /dev/null > @@ -1,262 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2711.dtsi" > -#include "bcm2711-rpi.dtsi" > -#include "bcm283x-rpi-usb-peripheral.dtsi" > - > -/ { > - compatible = "raspberrypi,4-model-b", "brcm,bcm2711"; > - model = "Raspberry Pi 4 Model B"; > - > - chosen { > - /* 8250 auxiliary UART instead of pl011 */ > - stdout-path = "serial1:115200n8"; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; > - }; > - > - led-pwr { > - label = "PWR"; > - gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; > - default-state = "keep"; > - linux,default-trigger = "default-on"; > - }; > - }; > - > - wifi_pwrseq: wifi-pwrseq { > - compatible = "mmc-pwrseq-simple"; > - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; > - }; > - > - sd_io_1v8_reg: sd_io_1v8_reg { > - compatible = "regulator-gpio"; > - regulator-name = "vdd-sd-io"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <3300000>; > - regulator-boot-on; > - regulator-always-on; > - regulator-settling-time-us = <5000>; > - gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; > - states = <1800000 0x1>, > - <3300000 0x0>; > - status = "okay"; > - }; > - > - sd_vcc_reg: sd_vcc_reg { > - compatible = "regulator-fixed"; > - regulator-name = "vcc-sd"; > - regulator-min-microvolt = <3300000>; > - regulator-max-microvolt = <3300000>; > - regulator-boot-on; > - enable-active-high; > - gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; > - }; > -}; > - > -&ddc0 { > - status = "okay"; > -}; > - > -&ddc1 { > - status = "okay"; > -}; > - > -&expgpio { > - gpio-line-names = "BT_ON", > - "WL_ON", > - "PWR_LED_OFF", > - "GLOBAL_RESET", > - "VDD_SD_IO_SEL", > - "CAM_GPIO", > - "SD_PWR_ON", > - ""; > -}; > - > -&gpio { > - /* > - * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and > - * the official GPU firmware DT blob. > - * > - * Legend: > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD1", > - "RXD1", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "RGMII_MDIO", > - "RGMIO_MDC", > - /* Used by BT module */ > - "CTS0", > - "RTS0", > - "TXD0", > - "RXD0", > - /* Used by Wifi */ > - "SD1_CLK", > - "SD1_CMD", > - "SD1_DATA0", > - "SD1_DATA1", > - "SD1_DATA2", > - "SD1_DATA3", > - /* Shared with SPI flash */ > - "PWM0_MISO", > - "PWM1_MOSI", > - "STATUS_LED_G_CLK", > - "SPIFLASH_CE_N", > - "SDA0", > - "SCL0", > - "RGMII_RXCLK", > - "RGMII_RXCTL", > - "RGMII_RXD0", > - "RGMII_RXD1", > - "RGMII_RXD2", > - "RGMII_RXD3", > - "RGMII_TXCLK", > - "RGMII_TXCTL", > - "RGMII_TXD0", > - "RGMII_TXD1", > - "RGMII_TXD2", > - "RGMII_TXD3"; > -}; > - > -&hdmi0 { > - status = "okay"; > -}; > - > -&hdmi1 { > - status = "okay"; > -}; > - > -&pixelvalve0 { > - status = "okay"; > -}; > - > -&pixelvalve1 { > - status = "okay"; > -}; > - > -&pixelvalve2 { > - status = "okay"; > -}; > - > -&pixelvalve4 { > - status = "okay"; > -}; > - > -&pwm1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>; > - status = "okay"; > -}; > - > -/* SDHCI is used to control the SDIO for wireless */ > -&sdhci { > - #address-cells = <1>; > - #size-cells = <0>; > - pinctrl-names = "default"; > - pinctrl-0 = <&emmc_gpio34>; > - bus-width = <4>; > - non-removable; > - mmc-pwrseq = <&wifi_pwrseq>; > - status = "okay"; > - > - brcmf: wifi@1 { > - reg = <1>; > - compatible = "brcm,bcm4329-fmac"; > - }; > -}; > - > -/* EMMC2 is used to drive the SD card */ > -&emmc2 { > - vqmmc-supply = <&sd_io_1v8_reg>; > - vmmc-supply = <&sd_vcc_reg>; > - broken-cd; > - status = "okay"; > -}; > - > -&genet { > - phy-handle = <&phy1>; > - phy-mode = "rgmii-rxid"; > - status = "okay"; > -}; > - > -&genet_mdio { > - phy1: ethernet-phy@1 { > - /* No PHY interrupt */ > - reg = <0x1>; > - }; > -}; > - > -&pcie0 { > - pci@0,0 { > - device_type = "pci"; > - #address-cells = <3>; > - #size-cells = <2>; > - ranges; > - > - reg = <0 0 0 0 0>; > - > - usb@0,0 { > - reg = <0 0 0 0 0>; > - resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>; > - }; > - }; > -}; > - > -/* uart0 communicates with the BT module */ > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; > - uart-has-rtscts; > - status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <2000000>; > - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; > - }; > -}; > - > -/* uart1 is mapped to the pin header */ > -&uart1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart1_gpio14>; > - status = "okay"; > -}; > - > -&vc4 { > - status = "okay"; > -}; > - > -&vec { > - status = "disabled"; > -}; > diff --git a/arch/arm/dts/bcm2711-rpi.dtsi b/arch/arm/dts/bcm2711-rpi.dtsi > deleted file mode 100644 > index ca266c5d9f9b..000000000000 > --- a/arch/arm/dts/bcm2711-rpi.dtsi > +++ /dev/null > @@ -1,74 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -#include "bcm2835-rpi.dtsi" > - > -#include <dt-bindings/reset/raspberrypi,firmware-reset.h> > - > -/ { > - /* Will be filled by the bootloader */ > - memory@0 { > - device_type = "memory"; > - reg = <0 0 0>; > - }; > - > - aliases { > - emmc2bus = &emmc2bus; > - ethernet0 = &genet; > - pcie0 = &pcie0; > - blconfig = &blconfig; > - }; > -}; > - > -&firmware { > - firmware_clocks: clocks { > - compatible = "raspberrypi,firmware-clocks"; > - #clock-cells = <1>; > - }; > - > - expgpio: gpio { > - compatible = "raspberrypi,firmware-gpio"; > - gpio-controller; > - #gpio-cells = <2>; > - status = "okay"; > - }; > - > - reset: reset { > - compatible = "raspberrypi,firmware-reset"; > - #reset-cells = <1>; > - }; > -}; > - > -&hdmi0 { > - clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>; > - clock-names = "hdmi", "bvb", "audio", "cec"; > - wifi-2.4ghz-coexistence; > -}; > - > -&hdmi1 { > - clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>; > - clock-names = "hdmi", "bvb", "audio", "cec"; > - wifi-2.4ghz-coexistence; > -}; > - > -&hvs { > - clocks = <&firmware_clocks 4>; > -}; > - > -&rmem { > - /* > - * RPi4's co-processor will copy the board's bootloader configuration > - * into memory for the OS to consume. It'll also update this node with > - * its placement information. > - */ > - blconfig: nvram@0 { > - compatible = "raspberrypi,bootloader-config", "nvmem-rmem"; > - #address-cells = <1>; > - #size-cells = <1>; > - reg = <0x0 0x0 0x0>; > - no-map; > - status = "disabled"; > - }; > -}; > - > -&vchiq { > - interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; > -}; > diff --git a/arch/arm/dts/bcm2711.dtsi b/arch/arm/dts/bcm2711.dtsi > deleted file mode 100644 > index 3b60297af7f6..000000000000 > --- a/arch/arm/dts/bcm2711.dtsi > +++ /dev/null > @@ -1,1100 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -#include "bcm283x.dtsi" > - > -#include <dt-bindings/interrupt-controller/arm-gic.h> > -#include <dt-bindings/soc/bcm2835-pm.h> > - > -/ { > - compatible = "brcm,bcm2711"; > - > - #address-cells = <2>; > - #size-cells = <1>; > - > - interrupt-parent = <&gicv2>; > - > - vc4: gpu { > - compatible = "brcm,bcm2711-vc5"; > - status = "disabled"; > - }; > - > - clk_27MHz: clk-27M { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <27000000>; > - clock-output-names = "27MHz-clock"; > - }; > - > - clk_108MHz: clk-108M { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <108000000>; > - clock-output-names = "108MHz-clock"; > - }; > - > - soc { > - /* > - * Defined ranges: > - * Common BCM283x peripherals > - * BCM2711-specific peripherals > - * ARM-local peripherals > - */ > - ranges = <0x7e000000 0x0 0xfe000000 0x01800000>, > - <0x7c000000 0x0 0xfc000000 0x02000000>, > - <0x40000000 0x0 0xff800000 0x00800000>; > - /* Emulate a contiguous 30-bit address range for DMA */ > - dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>; > - > - /* > - * This node is the provider for the enable-method for > - * bringing up secondary cores. > - */ > - local_intc: local_intc@40000000 { > - compatible = "brcm,bcm2836-l1-intc"; > - reg = <0x40000000 0x100>; > - }; > - > - gicv2: interrupt-controller@40041000 { > - interrupt-controller; > - #interrupt-cells = <3>; > - compatible = "arm,gic-400"; > - reg = <0x40041000 0x1000>, > - <0x40042000 0x2000>, > - <0x40044000 0x2000>, > - <0x40046000 0x2000>; > - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | > - IRQ_TYPE_LEVEL_HIGH)>; > - }; > - > - avs_monitor: avs-monitor@7d5d2000 { > - compatible = "brcm,bcm2711-avs-monitor", > - "syscon", "simple-mfd"; > - reg = <0x7d5d2000 0xf00>; > - > - thermal: thermal { > - compatible = "brcm,bcm2711-thermal"; > - #thermal-sensor-cells = <0>; > - }; > - }; > - > - dma: dma@7e007000 { > - compatible = "brcm,bcm2835-dma"; > - reg = <0x7e007000 0xb00>; > - interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, > - /* DMA lite 7 - 10 */ > - <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; > - interrupt-names = "dma0", > - "dma1", > - "dma2", > - "dma3", > - "dma4", > - "dma5", > - "dma6", > - "dma7", > - "dma8", > - "dma9", > - "dma10"; > - #dma-cells = <1>; > - brcm,dma-channel-mask = <0x07f5>; > - }; > - > - pm: watchdog@7e100000 { > - compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; > - #power-domain-cells = <1>; > - #reset-cells = <1>; > - reg = <0x7e100000 0x114>, > - <0x7e00a000 0x24>, > - <0x7ec11000 0x20>; > - clocks = <&clocks BCM2835_CLOCK_V3D>, > - <&clocks BCM2835_CLOCK_PERI_IMAGE>, > - <&clocks BCM2835_CLOCK_H264>, > - <&clocks BCM2835_CLOCK_ISP>; > - clock-names = "v3d", "peri_image", "h264", "isp"; > - system-power-controller; > - }; > - > - rng@7e104000 { > - compatible = "brcm,bcm2711-rng200"; > - reg = <0x7e104000 0x28>; > - }; > - > - uart2: serial@7e201400 { > - compatible = "arm,pl011", "arm,primecell"; > - reg = <0x7e201400 0x200>; > - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_UART>, > - <&clocks BCM2835_CLOCK_VPU>; > - clock-names = "uartclk", "apb_pclk"; > - arm,primecell-periphid = <0x00241011>; > - status = "disabled"; > - }; > - > - uart3: serial@7e201600 { > - compatible = "arm,pl011", "arm,primecell"; > - reg = <0x7e201600 0x200>; > - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_UART>, > - <&clocks BCM2835_CLOCK_VPU>; > - clock-names = "uartclk", "apb_pclk"; > - arm,primecell-periphid = <0x00241011>; > - status = "disabled"; > - }; > - > - uart4: serial@7e201800 { > - compatible = "arm,pl011", "arm,primecell"; > - reg = <0x7e201800 0x200>; > - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_UART>, > - <&clocks BCM2835_CLOCK_VPU>; > - clock-names = "uartclk", "apb_pclk"; > - arm,primecell-periphid = <0x00241011>; > - status = "disabled"; > - }; > - > - uart5: serial@7e201a00 { > - compatible = "arm,pl011", "arm,primecell"; > - reg = <0x7e201a00 0x200>; > - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_UART>, > - <&clocks BCM2835_CLOCK_VPU>; > - clock-names = "uartclk", "apb_pclk"; > - arm,primecell-periphid = <0x00241011>; > - status = "disabled"; > - }; > - > - spi3: spi@7e204600 { > - compatible = "brcm,bcm2835-spi"; > - reg = <0x7e204600 0x0200>; > - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - spi4: spi@7e204800 { > - compatible = "brcm,bcm2835-spi"; > - reg = <0x7e204800 0x0200>; > - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - spi5: spi@7e204a00 { > - compatible = "brcm,bcm2835-spi"; > - reg = <0x7e204a00 0x0200>; > - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - spi6: spi@7e204c00 { > - compatible = "brcm,bcm2835-spi"; > - reg = <0x7e204c00 0x0200>; > - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - i2c3: i2c@7e205600 { > - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; > - reg = <0x7e205600 0x200>; > - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - i2c4: i2c@7e205800 { > - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; > - reg = <0x7e205800 0x200>; > - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - i2c5: i2c@7e205a00 { > - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; > - reg = <0x7e205a00 0x200>; > - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - i2c6: i2c@7e205c00 { > - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; > - reg = <0x7e205c00 0x200>; > - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - pixelvalve0: pixelvalve@7e206000 { > - compatible = "brcm,bcm2711-pixelvalve0"; > - reg = <0x7e206000 0x100>; > - interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - }; > - > - pixelvalve1: pixelvalve@7e207000 { > - compatible = "brcm,bcm2711-pixelvalve1"; > - reg = <0x7e207000 0x100>; > - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - }; > - > - pixelvalve2: pixelvalve@7e20a000 { > - compatible = "brcm,bcm2711-pixelvalve2"; > - reg = <0x7e20a000 0x100>; > - interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - }; > - > - pwm1: pwm@7e20c800 { > - compatible = "brcm,bcm2835-pwm"; > - reg = <0x7e20c800 0x28>; > - clocks = <&clocks BCM2835_CLOCK_PWM>; > - assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; > - assigned-clock-rates = <10000000>; > - #pwm-cells = <2>; > - status = "disabled"; > - }; > - > - pixelvalve4: pixelvalve@7e216000 { > - compatible = "brcm,bcm2711-pixelvalve4"; > - reg = <0x7e216000 0x100>; > - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - }; > - > - hvs: hvs@7e400000 { > - compatible = "brcm,bcm2711-hvs"; > - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; > - }; > - > - pixelvalve3: pixelvalve@7ec12000 { > - compatible = "brcm,bcm2711-pixelvalve3"; > - reg = <0x7ec12000 0x100>; > - interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - }; > - > - vec: vec@7ec13000 { > - compatible = "brcm,bcm2711-vec"; > - reg = <0x7ec13000 0x1000>; > - clocks = <&clocks BCM2835_CLOCK_VEC>; > - interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - }; > - > - dvp: clock@7ef00000 { > - compatible = "brcm,brcm2711-dvp"; > - reg = <0x7ef00000 0x10>; > - clocks = <&clk_108MHz>; > - #clock-cells = <1>; > - #reset-cells = <1>; > - }; > - > - aon_intr: interrupt-controller@7ef00100 { > - compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; > - reg = <0x7ef00100 0x30>; > - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > - interrupt-controller; > - #interrupt-cells = <1>; > - }; > - > - hdmi0: hdmi@7ef00700 { > - compatible = "brcm,bcm2711-hdmi0"; > - reg = <0x7ef00700 0x300>, > - <0x7ef00300 0x200>, > - <0x7ef00f00 0x80>, > - <0x7ef00f80 0x80>, > - <0x7ef01b00 0x200>, > - <0x7ef01f00 0x400>, > - <0x7ef00200 0x80>, > - <0x7ef04300 0x100>, > - <0x7ef20000 0x100>; > - reg-names = "hdmi", > - "dvp", > - "phy", > - "rm", > - "packet", > - "metadata", > - "csc", > - "cec", > - "hd"; > - clock-names = "hdmi", "bvb", "audio", "cec"; > - resets = <&dvp 0>; > - interrupt-parent = <&aon_intr>; > - interrupts = <0>, <1>, <2>, > - <3>, <4>, <5>; > - interrupt-names = "cec-tx", "cec-rx", "cec-low", > - "wakeup", "hpd-connected", "hpd-removed"; > - ddc = <&ddc0>; > - dmas = <&dma 10>; > - dma-names = "audio-rx"; > - status = "disabled"; > - }; > - > - ddc0: i2c@7ef04500 { > - compatible = "brcm,bcm2711-hdmi-i2c"; > - reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; > - reg-names = "bsc", "auto-i2c"; > - clock-frequency = <97500>; > - status = "disabled"; > - }; > - > - hdmi1: hdmi@7ef05700 { > - compatible = "brcm,bcm2711-hdmi1"; > - reg = <0x7ef05700 0x300>, > - <0x7ef05300 0x200>, > - <0x7ef05f00 0x80>, > - <0x7ef05f80 0x80>, > - <0x7ef06b00 0x200>, > - <0x7ef06f00 0x400>, > - <0x7ef00280 0x80>, > - <0x7ef09300 0x100>, > - <0x7ef20000 0x100>; > - reg-names = "hdmi", > - "dvp", > - "phy", > - "rm", > - "packet", > - "metadata", > - "csc", > - "cec", > - "hd"; > - ddc = <&ddc1>; > - clock-names = "hdmi", "bvb", "audio", "cec"; > - resets = <&dvp 1>; > - interrupt-parent = <&aon_intr>; > - interrupts = <8>, <7>, <6>, > - <9>, <10>, <11>; > - interrupt-names = "cec-tx", "cec-rx", "cec-low", > - "wakeup", "hpd-connected", "hpd-removed"; > - dmas = <&dma 17>; > - dma-names = "audio-rx"; > - status = "disabled"; > - }; > - > - ddc1: i2c@7ef09500 { > - compatible = "brcm,bcm2711-hdmi-i2c"; > - reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; > - reg-names = "bsc", "auto-i2c"; > - clock-frequency = <97500>; > - status = "disabled"; > - }; > - }; > - > - /* > - * emmc2 has different DMA constraints based on SoC revisions. It was > - * moved into its own bus, so as for RPi4's firmware to update them. > - * The firmware will find whether the emmc2bus alias is defined, and if > - * so, it'll edit the dma-ranges property below accordingly. > - */ > - emmc2bus: emmc2bus { > - compatible = "simple-bus"; > - #address-cells = <2>; > - #size-cells = <1>; > - > - ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>; > - dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>; > - > - emmc2: mmc@7e340000 { > - compatible = "brcm,bcm2711-emmc2"; > - reg = <0x0 0x7e340000 0x100>; > - interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clocks BCM2711_CLOCK_EMMC2>; > - status = "disabled"; > - }; > - }; > - > - arm-pmu { > - compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3"; > - interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; > - interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; > - }; > - > - timer { > - compatible = "arm,armv8-timer"; > - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | > - IRQ_TYPE_LEVEL_LOW)>, > - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | > - IRQ_TYPE_LEVEL_LOW)>, > - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | > - IRQ_TYPE_LEVEL_LOW)>, > - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | > - IRQ_TYPE_LEVEL_LOW)>; > - /* This only applies to the ARMv7 stub */ > - arm,cpu-registers-not-fw-configured; > - }; > - > - cpus: cpus { > - #address-cells = <1>; > - #size-cells = <0>; > - enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit > - > - cpu0: cpu@0 { > - device_type = "cpu"; > - compatible = "arm,cortex-a72"; > - reg = <0>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000d8>; > - }; > - > - cpu1: cpu@1 { > - device_type = "cpu"; > - compatible = "arm,cortex-a72"; > - reg = <1>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000e0>; > - }; > - > - cpu2: cpu@2 { > - device_type = "cpu"; > - compatible = "arm,cortex-a72"; > - reg = <2>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000e8>; > - }; > - > - cpu3: cpu@3 { > - device_type = "cpu"; > - compatible = "arm,cortex-a72"; > - reg = <3>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000f0>; > - }; > - }; > - > - scb { > - compatible = "simple-bus"; > - #address-cells = <2>; > - #size-cells = <1>; > - > - ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, > - <0x6 0x00000000 0x6 0x00000000 0x40000000>; > - > - pcie0: pcie@7d500000 { > - compatible = "brcm,bcm2711-pcie"; > - reg = <0x0 0x7d500000 0x9310>; > - device_type = "pci"; > - #address-cells = <3>; > - #interrupt-cells = <1>; > - #size-cells = <2>; > - interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; > - interrupt-names = "pcie", "msi"; > - interrupt-map-mask = <0x0 0x0 0x0 0x7>; > - interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 > - IRQ_TYPE_LEVEL_HIGH>; > - msi-controller; > - msi-parent = <&pcie0>; > - > - ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 > - 0x0 0x04000000>; > - /* > - * The wrapper around the PCIe block has a bug > - * preventing it from accessing beyond the first 3GB of > - * memory. > - */ > - dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 > - 0x0 0xc0000000>; > - brcm,enable-ssc; > - }; > - > - genet: ethernet@7d580000 { > - compatible = "brcm,bcm2711-genet-v5"; > - reg = <0x0 0x7d580000 0x10000>; > - #address-cells = <0x1>; > - #size-cells = <0x1>; > - interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; > - status = "disabled"; > - > - genet_mdio: mdio@e14 { > - compatible = "brcm,genet-mdio-v5"; > - reg = <0xe14 0x8>; > - reg-names = "mdio"; > - #address-cells = <0x1>; > - #size-cells = <0x0>; > - }; > - }; > - }; > -}; > - > -&clk_osc { > - clock-frequency = <54000000>; > -}; > - > -&clocks { > - compatible = "brcm,bcm2711-cprman"; > -}; > - > -&cpu_thermal { > - coefficients = <(-487) 410040>; > - thermal-sensors = <&thermal>; > -}; > - > -&dsi0 { > - interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&dsi1 { > - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > - compatible = "brcm,bcm2711-dsi1"; > -}; > - > -&gpio { > - compatible = "brcm,bcm2711-gpio"; > - interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; > - > - gpclk0_gpio49: gpclk0_gpio49 { > - pin-gpclk { > - pins = "gpio49"; > - function = "alt1"; > - bias-disable; > - }; > - }; > - gpclk1_gpio50: gpclk1_gpio50 { > - pin-gpclk { > - pins = "gpio50"; > - function = "alt1"; > - bias-disable; > - }; > - }; > - gpclk2_gpio51: gpclk2_gpio51 { > - pin-gpclk { > - pins = "gpio51"; > - function = "alt1"; > - bias-disable; > - }; > - }; > - > - i2c0_gpio46: i2c0_gpio46 { > - pin-sda { > - function = "alt0"; > - pins = "gpio46"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt0"; > - pins = "gpio47"; > - bias-disable; > - }; > - }; > - i2c1_gpio46: i2c1_gpio46 { > - pin-sda { > - function = "alt1"; > - pins = "gpio46"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt1"; > - pins = "gpio47"; > - bias-disable; > - }; > - }; > - i2c3_gpio2: i2c3_gpio2 { > - pin-sda { > - function = "alt5"; > - pins = "gpio2"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio3"; > - bias-disable; > - }; > - }; > - i2c3_gpio4: i2c3_gpio4 { > - pin-sda { > - function = "alt5"; > - pins = "gpio4"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio5"; > - bias-disable; > - }; > - }; > - i2c4_gpio6: i2c4_gpio6 { > - pin-sda { > - function = "alt5"; > - pins = "gpio6"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio7"; > - bias-disable; > - }; > - }; > - i2c4_gpio8: i2c4_gpio8 { > - pin-sda { > - function = "alt5"; > - pins = "gpio8"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio9"; > - bias-disable; > - }; > - }; > - i2c5_gpio10: i2c5_gpio10 { > - pin-sda { > - function = "alt5"; > - pins = "gpio10"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio11"; > - bias-disable; > - }; > - }; > - i2c5_gpio12: i2c5_gpio12 { > - pin-sda { > - function = "alt5"; > - pins = "gpio12"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio13"; > - bias-disable; > - }; > - }; > - i2c6_gpio0: i2c6_gpio0 { > - pin-sda { > - function = "alt5"; > - pins = "gpio0"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio1"; > - bias-disable; > - }; > - }; > - i2c6_gpio22: i2c6_gpio22 { > - pin-sda { > - function = "alt5"; > - pins = "gpio22"; > - bias-pull-up; > - }; > - pin-scl { > - function = "alt5"; > - pins = "gpio23"; > - bias-disable; > - }; > - }; > - i2c_slave_gpio8: i2c_slave_gpio8 { > - pins-i2c-slave { > - pins = "gpio8", > - "gpio9", > - "gpio10", > - "gpio11"; > - function = "alt3"; > - }; > - }; > - > - jtag_gpio48: jtag_gpio48 { > - pins-jtag { > - pins = "gpio48", > - "gpio49", > - "gpio50", > - "gpio51", > - "gpio52", > - "gpio53"; > - function = "alt4"; > - }; > - }; > - > - mii_gpio28: mii_gpio28 { > - pins-mii { > - pins = "gpio28", > - "gpio29", > - "gpio30", > - "gpio31"; > - function = "alt4"; > - }; > - }; > - mii_gpio36: mii_gpio36 { > - pins-mii { > - pins = "gpio36", > - "gpio37", > - "gpio38", > - "gpio39"; > - function = "alt5"; > - }; > - }; > - > - pcm_gpio50: pcm_gpio50 { > - pins-pcm { > - pins = "gpio50", > - "gpio51", > - "gpio52", > - "gpio53"; > - function = "alt2"; > - }; > - }; > - > - pwm0_0_gpio12: pwm0_0_gpio12 { > - pin-pwm { > - pins = "gpio12"; > - function = "alt0"; > - bias-disable; > - }; > - }; > - pwm0_0_gpio18: pwm0_0_gpio18 { > - pin-pwm { > - pins = "gpio18"; > - function = "alt5"; > - bias-disable; > - }; > - }; > - pwm1_0_gpio40: pwm1_0_gpio40 { > - pin-pwm { > - pins = "gpio40"; > - function = "alt0"; > - bias-disable; > - }; > - }; > - pwm0_1_gpio13: pwm0_1_gpio13 { > - pin-pwm { > - pins = "gpio13"; > - function = "alt0"; > - bias-disable; > - }; > - }; > - pwm0_1_gpio19: pwm0_1_gpio19 { > - pin-pwm { > - pins = "gpio19"; > - function = "alt5"; > - bias-disable; > - }; > - }; > - pwm1_1_gpio41: pwm1_1_gpio41 { > - pin-pwm { > - pins = "gpio41"; > - function = "alt0"; > - bias-disable; > - }; > - }; > - pwm0_1_gpio45: pwm0_1_gpio45 { > - pin-pwm { > - pins = "gpio45"; > - function = "alt0"; > - bias-disable; > - }; > - }; > - pwm0_0_gpio52: pwm0_0_gpio52 { > - pin-pwm { > - pins = "gpio52"; > - function = "alt1"; > - bias-disable; > - }; > - }; > - pwm0_1_gpio53: pwm0_1_gpio53 { > - pin-pwm { > - pins = "gpio53"; > - function = "alt1"; > - bias-disable; > - }; > - }; > - > - rgmii_gpio35: rgmii_gpio35 { > - pin-start-stop { > - pins = "gpio35"; > - function = "alt4"; > - }; > - pin-rx-ok { > - pins = "gpio36"; > - function = "alt4"; > - }; > - }; > - rgmii_irq_gpio34: rgmii_irq_gpio34 { > - pin-irq { > - pins = "gpio34"; > - function = "alt5"; > - }; > - }; > - rgmii_irq_gpio39: rgmii_irq_gpio39 { > - pin-irq { > - pins = "gpio39"; > - function = "alt4"; > - }; > - }; > - rgmii_mdio_gpio28: rgmii_mdio_gpio28 { > - pins-mdio { > - pins = "gpio28", > - "gpio29"; > - function = "alt5"; > - }; > - }; > - rgmii_mdio_gpio37: rgmii_mdio_gpio37 { > - pins-mdio { > - pins = "gpio37", > - "gpio38"; > - function = "alt4"; > - }; > - }; > - > - spi0_gpio46: spi0_gpio46 { > - pins-spi { > - pins = "gpio46", > - "gpio47", > - "gpio48", > - "gpio49"; > - function = "alt2"; > - }; > - }; > - spi2_gpio46: spi2_gpio46 { > - pins-spi { > - pins = "gpio46", > - "gpio47", > - "gpio48", > - "gpio49", > - "gpio50"; > - function = "alt5"; > - }; > - }; > - spi3_gpio0: spi3_gpio0 { > - pins-spi { > - pins = "gpio0", > - "gpio1", > - "gpio2", > - "gpio3"; > - function = "alt3"; > - }; > - }; > - spi4_gpio4: spi4_gpio4 { > - pins-spi { > - pins = "gpio4", > - "gpio5", > - "gpio6", > - "gpio7"; > - function = "alt3"; > - }; > - }; > - spi5_gpio12: spi5_gpio12 { > - pins-spi { > - pins = "gpio12", > - "gpio13", > - "gpio14", > - "gpio15"; > - function = "alt3"; > - }; > - }; > - spi6_gpio18: spi6_gpio18 { > - pins-spi { > - pins = "gpio18", > - "gpio19", > - "gpio20", > - "gpio21"; > - function = "alt3"; > - }; > - }; > - > - uart2_gpio0: uart2_gpio0 { > - pin-tx { > - pins = "gpio0"; > - function = "alt4"; > - bias-disable; > - }; > - pin-rx { > - pins = "gpio1"; > - function = "alt4"; > - bias-pull-up; > - }; > - }; > - uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 { > - pin-cts { > - pins = "gpio2"; > - function = "alt4"; > - bias-pull-up; > - }; > - pin-rts { > - pins = "gpio3"; > - function = "alt4"; > - bias-disable; > - }; > - }; > - uart3_gpio4: uart3_gpio4 { > - pin-tx { > - pins = "gpio4"; > - function = "alt4"; > - bias-disable; > - }; > - pin-rx { > - pins = "gpio5"; > - function = "alt4"; > - bias-pull-up; > - }; > - }; > - uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 { > - pin-cts { > - pins = "gpio6"; > - function = "alt4"; > - bias-pull-up; > - }; > - pin-rts { > - pins = "gpio7"; > - function = "alt4"; > - bias-disable; > - }; > - }; > - uart4_gpio8: uart4_gpio8 { > - pin-tx { > - pins = "gpio8"; > - function = "alt4"; > - bias-disable; > - }; > - pin-rx { > - pins = "gpio9"; > - function = "alt4"; > - bias-pull-up; > - }; > - }; > - uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 { > - pin-cts { > - pins = "gpio10"; > - function = "alt4"; > - bias-pull-up; > - }; > - pin-rts { > - pins = "gpio11"; > - function = "alt4"; > - bias-disable; > - }; > - }; > - uart5_gpio12: uart5_gpio12 { > - pin-tx { > - pins = "gpio12"; > - function = "alt4"; > - bias-disable; > - }; > - pin-rx { > - pins = "gpio13"; > - function = "alt4"; > - bias-pull-up; > - }; > - }; > - uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 { > - pin-cts { > - pins = "gpio14"; > - function = "alt4"; > - bias-pull-up; > - }; > - pin-rts { > - pins = "gpio15"; > - function = "alt4"; > - bias-disable; > - }; > - }; > -}; > - > -&rmem { > - #address-cells = <2>; > -}; > - > -&cma { > - /* > - * arm64 reserves the CMA by default somewhere in ZONE_DMA32, > - * that's not good enough for the BCM2711 as some devices can > - * only address the lower 1G of memory (ZONE_DMA). > - */ > - alloc-ranges = <0x0 0x00000000 0x40000000>; > -}; > - > -&i2c0 { > - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; > - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&i2c1 { > - compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; > - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&mailbox { > - interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&sdhci { > - interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&sdhost { > - interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&spi { > - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&spi1 { > - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&spi2 { > - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&system_timer { > - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&txp { > - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&uart0 { > - interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&uart1 { > - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&usb { > - interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&vec { > - compatible = "brcm,bcm2711-vec"; > - interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; > -}; > diff --git a/arch/arm/dts/bcm2835-common.dtsi b/arch/arm/dts/bcm2835-common.dtsi > deleted file mode 100644 > index c25e797b9060..000000000000 > --- a/arch/arm/dts/bcm2835-common.dtsi > +++ /dev/null > @@ -1,207 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > - > -/* This include file covers the common peripherals and configuration between > - * bcm2835, bcm2836 and bcm2837 implementations. > - */ > - > -/ { > - interrupt-parent = <&intc>; > - > - soc { > - dma: dma@7e007000 { > - compatible = "brcm,bcm2835-dma"; > - reg = <0x7e007000 0xf00>; > - interrupts = <1 16>, > - <1 17>, > - <1 18>, > - <1 19>, > - <1 20>, > - <1 21>, > - <1 22>, > - <1 23>, > - <1 24>, > - <1 25>, > - <1 26>, > - /* dma channel 11-14 share one irq */ > - <1 27>, > - <1 27>, > - <1 27>, > - <1 27>, > - /* unused shared irq for all channels */ > - <1 28>; > - interrupt-names = "dma0", > - "dma1", > - "dma2", > - "dma3", > - "dma4", > - "dma5", > - "dma6", > - "dma7", > - "dma8", > - "dma9", > - "dma10", > - "dma11", > - "dma12", > - "dma13", > - "dma14", > - "dma-shared-all"; > - #dma-cells = <1>; > - brcm,dma-channel-mask = <0x7f35>; > - }; > - > - intc: interrupt-controller@7e00b200 { > - compatible = "brcm,bcm2835-armctrl-ic"; > - reg = <0x7e00b200 0x200>; > - interrupt-controller; > - #interrupt-cells = <2>; > - }; > - > - pm: watchdog@7e100000 { > - compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; > - #power-domain-cells = <1>; > - #reset-cells = <1>; > - reg = <0x7e100000 0x114>, > - <0x7e00a000 0x24>; > - clocks = <&clocks BCM2835_CLOCK_V3D>, > - <&clocks BCM2835_CLOCK_PERI_IMAGE>, > - <&clocks BCM2835_CLOCK_H264>, > - <&clocks BCM2835_CLOCK_ISP>; > - clock-names = "v3d", "peri_image", "h264", "isp"; > - system-power-controller; > - }; > - > - rng@7e104000 { > - compatible = "brcm,bcm2835-rng"; > - reg = <0x7e104000 0x10>; > - interrupts = <2 29>; > - }; > - > - pixelvalve@7e206000 { > - compatible = "brcm,bcm2835-pixelvalve0"; > - reg = <0x7e206000 0x100>; > - interrupts = <2 13>; /* pwa0 */ > - }; > - > - pixelvalve@7e207000 { > - compatible = "brcm,bcm2835-pixelvalve1"; > - reg = <0x7e207000 0x100>; > - interrupts = <2 14>; /* pwa1 */ > - }; > - > - thermal: thermal@7e212000 { > - compatible = "brcm,bcm2835-thermal"; > - reg = <0x7e212000 0x8>; > - clocks = <&clocks BCM2835_CLOCK_TSENS>; > - #thermal-sensor-cells = <0>; > - status = "disabled"; > - }; > - > - i2c2: i2c@7e805000 { > - compatible = "brcm,bcm2835-i2c"; > - reg = <0x7e805000 0x1000>; > - interrupts = <2 21>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "okay"; > - }; > - > - vec: vec@7e806000 { > - compatible = "brcm,bcm2835-vec"; > - reg = <0x7e806000 0x1000>; > - clocks = <&clocks BCM2835_CLOCK_VEC>; > - interrupts = <2 27>; > - status = "disabled"; > - }; > - > - pixelvalve@7e807000 { > - compatible = "brcm,bcm2835-pixelvalve2"; > - reg = <0x7e807000 0x100>; > - interrupts = <2 10>; /* pixelvalve */ > - }; > - > - hdmi: hdmi@7e902000 { > - compatible = "brcm,bcm2835-hdmi"; > - reg = <0x7e902000 0x600>, > - <0x7e808000 0x100>; > - interrupts = <2 8>, <2 9>; > - ddc = <&i2c2>; > - clocks = <&clocks BCM2835_PLLH_PIX>, > - <&clocks BCM2835_CLOCK_HSM>; > - clock-names = "pixel", "hdmi"; > - dmas = <&dma 17>; > - dma-names = "audio-rx"; > - status = "disabled"; > - }; > - > - v3d: v3d@7ec00000 { > - compatible = "brcm,bcm2835-v3d"; > - reg = <0x7ec00000 0x1000>; > - interrupts = <1 10>; > - }; > - > - vc4: gpu { > - compatible = "brcm,bcm2835-vc4"; > - }; > - }; > -}; > - > -&cpu_thermal { > - thermal-sensors = <&thermal>; > -}; > - > -&gpio { > - i2c_slave_gpio18: i2c_slave_gpio18 { > - brcm,pins = <18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - }; > - > - jtag_gpio4: jtag_gpio4 { > - brcm,pins = <4 5 6 12 13>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - > - pwm0_gpio12: pwm0_gpio12 { > - brcm,pins = <12>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - pwm0_gpio18: pwm0_gpio18 { > - brcm,pins = <18>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - pwm0_gpio40: pwm0_gpio40 { > - brcm,pins = <40>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - pwm1_gpio13: pwm1_gpio13 { > - brcm,pins = <13>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - pwm1_gpio19: pwm1_gpio19 { > - brcm,pins = <19>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - pwm1_gpio41: pwm1_gpio41 { > - brcm,pins = <41>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - pwm1_gpio45: pwm1_gpio45 { > - brcm,pins = <45>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > -}; > - > -&i2s { > - dmas = <&dma 2>, <&dma 3>; > - dma-names = "tx", "rx"; > -}; > - > -&sdhost { > - dmas = <&dma 13>; > - dma-names = "rx-tx"; > -}; > - > -&spi { > - dmas = <&dma 6>, <&dma 7>; > - dma-names = "tx", "rx"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts > deleted file mode 100644 > index 40b9405f1a8e..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-a-plus.dts > +++ /dev/null > @@ -1,128 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,model-a-plus", "brcm,bcm2835"; > - model = "Raspberry Pi Model A+"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x10000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; > - }; > - > - led-pwr { > - label = "PWR"; > - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; > - default-state = "keep"; > - linux,default-trigger = "default-on"; > - }; > - }; > -}; > - > -&gpio { > - /* > - * This is based on the unreleased schematic for the Model A+. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD0", > - "RXD0", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "SDA0", > - "SCL0", > - "NC", /* GPIO30 */ > - "NC", /* GPIO31 */ > - "CAM_GPIO1", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "PWR_LOW_N", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "USB_LIMIT", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "PWM0_OUT", /* GPIO40 */ > - "CAM_GPIO0", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "NC", /* GPIO43 */ > - "NC", /* GPIO44 */ > - "PWM1_OUT", /* GPIO45 */ > - "HDMI_HPD_N", > - "STATUS_LED", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; > - > - /* I2S interface */ > - i2s_alt0: i2s_alt0 { > - brcm,pins = <18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts > deleted file mode 100644 > index 11edb581dbaf..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-a.dts > +++ /dev/null > @@ -1,123 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,model-a", "brcm,bcm2835"; > - model = "Raspberry Pi Model A"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x10000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; > - }; > - }; > -}; > - > -&gpio { > - /* > - * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf > - * RPI00021 sheet 02 > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "SDA0", > - "SCL0", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "CAM_GPIO1", > - "LAN_RUN", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "NC", /* GPIO12 */ > - "NC", /* GPIO13 */ > - /* Serial port */ > - "TXD0", > - "RXD0", > - "STATUS_LED_N", > - "GPIO17", > - "GPIO18", > - "NC", /* GPIO19 */ > - "NC", /* GPIO20 */ > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "NC", /* GPIO26 */ > - "CAM_GPIO0", > - /* Binary number representing build/revision */ > - "CONFIG0", > - "CONFIG1", > - "CONFIG2", > - "CONFIG3", > - "NC", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "NC", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "NC", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "PWM0_OUT", > - "NC", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "NC", /* GPIO43 */ > - "NC", /* GPIO44 */ > - "PWM1_OUT", > - "HDMI_HPD_P", > - "SD_CARD_DET", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; > - > - /* I2S interface */ > - i2s_alt2: i2s_alt2 { > - brcm,pins = <28 29 30 31>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts > deleted file mode 100644 > index 1b435c64bd9c..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-b-plus.dts > +++ /dev/null > @@ -1,130 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-smsc9514.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; > - model = "Raspberry Pi Model B+"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x20000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; > - }; > - > - led-pwr { > - label = "PWR"; > - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; > - default-state = "keep"; > - linux,default-trigger = "default-on"; > - }; > - }; > -}; > - > -&gpio { > - /* > - * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf > - * RPI-BPLUS sheet 1 > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD0", > - "RXD0", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "SDA0", > - "SCL0", > - "NC", /* GPIO30 */ > - "LAN_RUN", /* GPIO31 */ > - "CAM_GPIO1", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "PWR_LOW_N", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "USB_LIMIT", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "PWM0_OUT", /* GPIO40 */ > - "CAM_GPIO0", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "NC", /* GPIO43 */ > - "ETHCLK", /* GPIO44 */ > - "PWM1_OUT", /* GPIO45 */ > - "HDMI_HPD_N", > - "STATUS_LED", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; > - > - /* I2S interface */ > - i2s_alt0: i2s_alt0 { > - brcm,pins = <18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts > deleted file mode 100644 > index a23c25c00eea..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts > +++ /dev/null > @@ -1,123 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-smsc9512.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; > - model = "Raspberry Pi Model B rev2"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x10000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; > - }; > - }; > -}; > - > -&gpio { > - /* > - * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf > - * RPI00022 sheet 02 > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "SDA0", > - "SCL0", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "CAM_CLK", > - "LAN_RUN", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "NC", /* GPIO12 */ > - "NC", /* GPIO13 */ > - /* Serial port */ > - "TXD0", > - "RXD0", > - "STATUS_LED_N", > - "GPIO17", > - "GPIO18", > - "NC", /* GPIO19 */ > - "NC", /* GPIO20 */ > - "CAM_GPIO", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "NC", /* GPIO26 */ > - "GPIO27", > - "GPIO28", > - "GPIO29", > - "GPIO30", > - "GPIO31", > - "NC", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "NC", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "NC", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "PWM0_OUT", > - "NC", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "NC", /* GPIO43 */ > - "NC", /* GPIO44 */ > - "PWM1_OUT", > - "HDMI_HPD_P", > - "SD_CARD_DET", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; > - > - /* I2S interface */ > - i2s_alt2: i2s_alt2 { > - brcm,pins = <28 29 30 31>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts > deleted file mode 100644 > index 1b63d6b19750..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-b.dts > +++ /dev/null > @@ -1,118 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-smsc9512.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,model-b", "brcm,bcm2835"; > - model = "Raspberry Pi Model B"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x10000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; > - }; > - }; > -}; > - > -&gpio { > - /* > - * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf > - * RPI00021 sheet 02 > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "SDA0", > - "SCL0", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "CAM_GPIO1", > - "LAN_RUN", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "NC", /* GPIO12 */ > - "NC", /* GPIO13 */ > - /* Serial port */ > - "TXD0", > - "RXD0", > - "STATUS_LED_N", > - "GPIO17", > - "GPIO18", > - "NC", /* GPIO19 */ > - "NC", /* GPIO20 */ > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "NC", /* GPIO26 */ > - "CAM_GPIO0", > - /* Binary number representing build/revision */ > - "CONFIG0", > - "CONFIG1", > - "CONFIG2", > - "CONFIG3", > - "NC", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "NC", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "NC", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "PWM0_OUT", > - "NC", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "NC", /* GPIO43 */ > - "NC", /* GPIO44 */ > - "PWM1_OUT", > - "HDMI_HPD_P", > - "SD_CARD_DET", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0>; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts > deleted file mode 100644 > index a75c882e6575..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts > +++ /dev/null > @@ -1,97 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835-rpi-cm1.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,compute-module", "brcm,bcm2835"; > - model = "Raspberry Pi Compute Module IO board rev1"; > -}; > - > -&gpio { > - /* > - * This is based on the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "GPIO0", > - "GPIO1", > - "GPIO2", > - "GPIO3", > - "GPIO4", > - "GPIO5", > - "GPIO6", > - "GPIO7", > - "GPIO8", > - "GPIO9", > - "GPIO10", > - "GPIO11", > - "GPIO12", > - "GPIO13", > - "GPIO14", > - "GPIO15", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "GPIO28", > - "GPIO29", > - "GPIO30", > - "GPIO31", > - "GPIO32", > - "GPIO33", > - "GPIO34", > - "GPIO35", > - "GPIO36", > - "GPIO37", > - "GPIO38", > - "GPIO39", > - "GPIO40", > - "GPIO41", > - "GPIO42", > - "GPIO43", > - "GPIO44", > - "GPIO45", > - "HDMI_HPD_N", > - /* Also used as ACT LED */ > - "EMMC_EN_N", > - /* Used by eMMC */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0>; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/dts/bcm2835-rpi-cm1.dtsi > deleted file mode 100644 > index e4e6b6abbfc1..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-cm1.dtsi > +++ /dev/null > @@ -1,39 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > - > -/ { > - leds { > - led-act { > - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; > - }; > - }; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x20000000>; > - }; > - > - reg_3v3: fixed-regulator { > - compatible = "regulator-fixed"; > - regulator-name = "3V3"; > - regulator-min-microvolt = <3300000>; > - regulator-max-microvolt = <3300000>; > - regulator-always-on; > - }; > - > - reg_1v8: fixed-regulator { > - compatible = "regulator-fixed"; > - regulator-name = "1V8"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <1800000>; > - regulator-always-on; > - }; > -}; > - > -&sdhost { > - non-removable; > - vmmc-supply = <®_3v3>; > - vqmmc-supply = <®_1v8>; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-common.dtsi b/arch/arm/dts/bcm2835-rpi-common.dtsi > deleted file mode 100644 > index 8a55b6cded59..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-common.dtsi > +++ /dev/null > @@ -1,12 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/* > - * This include file covers the common peripherals and configuration between > - * bcm2835, bcm2836 and bcm2837 implementations that interact with RPi's > - * firmware interface. > - */ > - > -#include <dt-bindings/power/raspberrypi-power.h> > - > -&v3d { > - power-domains = <&power RPI_POWER_DOMAIN_V3D>; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts > deleted file mode 100644 > index 33b2b77aa47d..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-zero-w.dts > +++ /dev/null > @@ -1,151 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com> > - */ > - > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-usb-otg.dtsi" > - > -/ { > - compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; > - model = "Raspberry Pi Zero W"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x20000000>; > - }; > - > - chosen { > - /* 8250 auxiliary UART instead of pl011 */ > - stdout-path = "serial1:115200n8"; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; > - }; > - }; > - > - wifi_pwrseq: wifi-pwrseq { > - compatible = "mmc-pwrseq-simple"; > - reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>; > - }; > -}; > - > -&gpio { > - /* > - * This is based on the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD0", > - "RXD0", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "SDA0", > - "SCL0", > - "NC", /* GPIO30 */ > - "NC", /* GPIO31 */ > - "NC", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "NC", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "NC", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "CAM_GPIO1", /* GPIO40 */ > - "WL_ON", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "WIFI_CLK", /* GPIO43 */ > - "CAM_GPIO0", /* GPIO44 */ > - "BT_ON", /* GPIO45 */ > - "HDMI_HPD_N", > - "STATUS_LED_N", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0>; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&sdhci { > - #address-cells = <1>; > - #size-cells = <0>; > - pinctrl-names = "default"; > - pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>; > - bus-width = <4>; > - mmc-pwrseq = <&wifi_pwrseq>; > - non-removable; > - status = "okay"; > - > - brcmf: wifi@1 { > - reg = <1>; > - compatible = "brcm,bcm4329-fmac"; > - }; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>; > - status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <2000000>; > - shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; > - }; > -}; > - > -&uart1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart1_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi-zero.dts b/arch/arm/dts/bcm2835-rpi-zero.dts > deleted file mode 100644 > index 6f9b3a908f28..000000000000 > --- a/arch/arm/dts/bcm2835-rpi-zero.dts > +++ /dev/null > @@ -1,119 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com> > - */ > - > -/dts-v1/; > -#include "bcm2835.dtsi" > -#include "bcm2835-rpi.dtsi" > -#include "bcm283x-rpi-usb-otg.dtsi" > - > -/ { > - compatible = "raspberrypi,model-zero", "brcm,bcm2835"; > - model = "Raspberry Pi Zero"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x20000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; > - }; > - }; > -}; > - > -&gpio { > - /* > - * This is based on the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD0", > - "RXD0", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "SDA0", > - "SCL0", > - "NC", /* GPIO30 */ > - "NC", /* GPIO31 */ > - "CAM_GPIO1", /* GPIO32 */ > - "NC", /* GPIO33 */ > - "NC", /* GPIO34 */ > - "NC", /* GPIO35 */ > - "NC", /* GPIO36 */ > - "NC", /* GPIO37 */ > - "NC", /* GPIO38 */ > - "NC", /* GPIO39 */ > - "NC", /* GPIO40 */ > - "CAM_GPIO0", /* GPIO41 */ > - "NC", /* GPIO42 */ > - "NC", /* GPIO43 */ > - "NC", /* GPIO44 */ > - "NC", /* GPIO45 */ > - "HDMI_HPD_N", > - "STATUS_LED_N", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; > - > - /* I2S interface */ > - i2s_alt0: i2s_alt0 { > - brcm,pins = <18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi > deleted file mode 100644 > index 87ddcad76083..000000000000 > --- a/arch/arm/dts/bcm2835-rpi.dtsi > +++ /dev/null > @@ -1,81 +0,0 @@ > -#include <dt-bindings/power/raspberrypi-power.h> > - > -/ { > - leds { > - compatible = "gpio-leds"; > - > - led-act { > - label = "ACT"; > - default-state = "keep"; > - linux,default-trigger = "heartbeat"; > - }; > - }; > - > - soc { > - firmware: firmware { > - compatible = "raspberrypi,bcm2835-firmware", "simple-mfd"; > - #address-cells = <1>; > - #size-cells = <1>; > - > - mboxes = <&mailbox>; > - dma-ranges; > - }; > - > - power: power { > - compatible = "raspberrypi,bcm2835-power"; > - firmware = <&firmware>; > - #power-domain-cells = <1>; > - }; > - > - vchiq: mailbox@7e00b840 { > - compatible = "brcm,bcm2835-vchiq"; > - reg = <0x7e00b840 0x3c>; > - interrupts = <0 2>; > - }; > - }; > -}; > - > -&gpio { > - pinctrl-names = "default"; > - > - gpioout: gpioout { > - brcm,pins = <6>; > - brcm,function = <BCM2835_FSEL_GPIO_OUT>; > - }; > - > - alt0: alt0 { > - brcm,pins = <4 5 7 8 9 10 11>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > -}; > - > -&i2c0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&i2c0_gpio0>; > - status = "okay"; > - clock-frequency = <100000>; > -}; > - > -&i2c1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&i2c1_gpio2>; > - status = "okay"; > - clock-frequency = <100000>; > -}; > - > -&usb { > - power-domains = <&power RPI_POWER_DOMAIN_USB>; > -}; > - > -&vec { > - power-domains = <&power RPI_POWER_DOMAIN_VEC>; > - status = "okay"; > -}; > - > -&dsi0 { > - power-domains = <&power RPI_POWER_DOMAIN_DSI0>; > -}; > - > -&dsi1 { > - power-domains = <&power RPI_POWER_DOMAIN_DSI1>; > -}; > diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi > deleted file mode 100644 > index 0549686134ea..000000000000 > --- a/arch/arm/dts/bcm2835.dtsi > +++ /dev/null > @@ -1,38 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -#include "bcm283x.dtsi" > -#include "bcm2835-common.dtsi" > -#include "bcm2835-rpi-common.dtsi" > - > -/ { > - compatible = "brcm,bcm2835"; > - > - cpus { > - #address-cells = <1>; > - #size-cells = <0>; > - > - cpu@0 { > - device_type = "cpu"; > - compatible = "arm,arm1176jzf-s"; > - reg = <0x0>; > - }; > - }; > - > - soc { > - ranges = <0x7e000000 0x20000000 0x02000000>; > - dma-ranges = <0x40000000 0x00000000 0x20000000>; > - }; > - > - arm-pmu { > - compatible = "arm,arm1176-pmu"; > - }; > -}; > - > -&cpu_thermal { > - coefficients = <(-538) 407000>; > -}; > - > -/* enable thermal sensor with the correct compatible property set */ > -&thermal { > - compatible = "brcm,bcm2835-thermal"; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts > deleted file mode 100644 > index d8af8eeac7b6..000000000000 > --- a/arch/arm/dts/bcm2836-rpi-2-b.dts > +++ /dev/null > @@ -1,130 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2836.dtsi" > -#include "bcm2836-rpi.dtsi" > -#include "bcm283x-rpi-smsc9514.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; > - model = "Raspberry Pi 2 Model B"; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x40000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; > - }; > - > - led-pwr { > - label = "PWR"; > - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; > - default-state = "keep"; > - linux,default-trigger = "default-on"; > - }; > - }; > -}; > - > -&gpio { > - /* > - * Taken from rpi_SCH_2b_1p2_reduced.pdf and > - * the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD0", > - "RXD0", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "SDA0", > - "SCL0", > - "", /* GPIO30 */ > - "LAN_RUN", > - "CAM_GPIO1", > - "", /* GPIO33 */ > - "", /* GPIO34 */ > - "PWR_LOW_N", > - "", /* GPIO36 */ > - "", /* GPIO37 */ > - "USB_LIMIT", > - "", /* GPIO39 */ > - "PWM0_OUT", > - "CAM_GPIO0", > - "SMPS_SCL", > - "SMPS_SDA", > - "ETHCLK", > - "PWM1_OUT", > - "HDMI_HPD_N", > - "STATUS_LED", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; > - > - /* I2S interface */ > - i2s_alt0: i2s_alt0 { > - brcm,pins = <18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2836-rpi.dtsi b/arch/arm/dts/bcm2836-rpi.dtsi > deleted file mode 100644 > index c4c858b984c6..000000000000 > --- a/arch/arm/dts/bcm2836-rpi.dtsi > +++ /dev/null > @@ -1,6 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -#include "bcm2835-rpi.dtsi" > - > -&vchiq { > - compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq"; > -}; > diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi > deleted file mode 100644 > index b390006aef79..000000000000 > --- a/arch/arm/dts/bcm2836.dtsi > +++ /dev/null > @@ -1,92 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -#include "bcm283x.dtsi" > -#include "bcm2835-common.dtsi" > -#include "bcm2835-rpi-common.dtsi" > - > -/ { > - compatible = "brcm,bcm2836"; > - > - soc { > - ranges = <0x7e000000 0x3f000000 0x1000000>, > - <0x40000000 0x40000000 0x00001000>; > - dma-ranges = <0xc0000000 0x00000000 0x3f000000>; > - > - local_intc: local_intc@40000000 { > - compatible = "brcm,bcm2836-l1-intc"; > - reg = <0x40000000 0x100>; > - interrupt-controller; > - #interrupt-cells = <2>; > - interrupt-parent = <&local_intc>; > - }; > - }; > - > - arm-pmu { > - compatible = "arm,cortex-a7-pmu"; > - interrupt-parent = <&local_intc>; > - interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; > - }; > - > - timer { > - compatible = "arm,armv7-timer"; > - interrupt-parent = <&local_intc>; > - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI > - <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI > - <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI > - <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI > - always-on; > - }; > - > - cpus: cpus { > - #address-cells = <1>; > - #size-cells = <0>; > - enable-method = "brcm,bcm2836-smp"; > - > - v7_cpu0: cpu@0 { > - device_type = "cpu"; > - compatible = "arm,cortex-a7"; > - reg = <0xf00>; > - clock-frequency = <800000000>; > - }; > - > - v7_cpu1: cpu@1 { > - device_type = "cpu"; > - compatible = "arm,cortex-a7"; > - reg = <0xf01>; > - clock-frequency = <800000000>; > - }; > - > - v7_cpu2: cpu@2 { > - device_type = "cpu"; > - compatible = "arm,cortex-a7"; > - reg = <0xf02>; > - clock-frequency = <800000000>; > - }; > - > - v7_cpu3: cpu@3 { > - device_type = "cpu"; > - compatible = "arm,cortex-a7"; > - reg = <0xf03>; > - clock-frequency = <800000000>; > - }; > - }; > -}; > - > -/* Make the BCM2835-style global interrupt controller be a child of the > - * CPU-local interrupt controller. > - */ > -&intc { > - compatible = "brcm,bcm2836-armctrl-ic"; > - reg = <0x7e00b200 0x200>; > - interrupt-parent = <&local_intc>; > - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&cpu_thermal { > - coefficients = <(-538) 407000>; > -}; > - > -/* enable thermal sensor with the correct compatible property set */ > -&thermal { > - compatible = "brcm,bcm2836-thermal"; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts > deleted file mode 100644 > index 77099a7871b0..000000000000 > --- a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts > +++ /dev/null > @@ -1,180 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2837.dtsi" > -#include "bcm2836-rpi.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837"; > - model = "Raspberry Pi 3 Model A+"; > - > - chosen { > - /* 8250 auxiliary UART instead of pl011 */ > - stdout-path = "serial1:115200n8"; > - }; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x20000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; > - }; > - > - led-pwr { > - label = "PWR"; > - gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; > - default-state = "keep"; > - linux,default-trigger = "default-on"; > - }; > - }; > -}; > - > -&firmware { > - expgpio: gpio { > - compatible = "raspberrypi,firmware-gpio"; > - gpio-controller; > - #gpio-cells = <2>; > - gpio-line-names = "", > - "BT_WL_ON", > - "STATUS_LED_R", > - "", > - "", > - "CAM_GPIO0", > - "CAM_GPIO1", > - ""; > - status = "okay"; > - }; > -}; > - > -&gpio { > - /* > - * This is mostly based on the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD1", > - "RXD1", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "HDMI_HPD_N", > - "STATUS_LED_G", > - /* Used by BT module */ > - "CTS0", > - "RTS0", > - "TXD0", > - "RXD0", > - /* Used by Wifi */ > - "SD1_CLK", > - "SD1_CMD", > - "SD1_DATA0", > - "SD1_DATA1", > - "SD1_DATA2", > - "SD1_DATA3", > - "PWM0_OUT", > - "PWM1_OUT", > - "", /* GPIO42 */ > - "WIFI_CLK", > - "SDA0", > - "SCL0", > - "SMPS_SCL", > - "SMPS_SDA", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; > - status = "okay"; > -}; > - > -/* > - * SDHCI is used to control the SDIO for wireless > - * > - * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven > - * by a single GPIO. We can't give GPIO control to one of the drivers, > - * otherwise the other part would get unexpectedly disturbed. > - */ > -&sdhci { > - #address-cells = <1>; > - #size-cells = <0>; > - pinctrl-names = "default"; > - pinctrl-0 = <&emmc_gpio34>; > - status = "okay"; > - bus-width = <4>; > - non-removable; > - > - brcmf: wifi@1 { > - reg = <1>; > - compatible = "brcm,bcm4329-fmac"; > - }; > -}; > - > -/* SDHOST is used to drive the SD card */ > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - status = "okay"; > - bus-width = <4>; > -}; > - > -/* uart0 communicates with the BT module */ > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; > - status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <2000000>; > - }; > -}; > - > -/* uart1 is mapped to the pin header */ > -&uart1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart1_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts > deleted file mode 100644 > index 61010266ca9a..000000000000 > --- a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts > +++ /dev/null > @@ -1,183 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2837.dtsi" > -#include "bcm2836-rpi.dtsi" > -#include "bcm283x-rpi-lan7515.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; > - model = "Raspberry Pi 3 Model B+"; > - > - chosen { > - /* 8250 auxiliary UART instead of pl011 */ > - stdout-path = "serial1:115200n8"; > - }; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x40000000>; > - }; > - > - leds { > - led-act { > - gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; > - }; > - > - led-pwr { > - label = "PWR"; > - gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; > - default-state = "keep"; > - linux,default-trigger = "default-on"; > - }; > - }; > - > - wifi_pwrseq: wifi-pwrseq { > - compatible = "mmc-pwrseq-simple"; > - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; > - }; > -}; > - > -&firmware { > - expgpio: gpio { > - compatible = "raspberrypi,firmware-gpio"; > - gpio-controller; > - #gpio-cells = <2>; > - gpio-line-names = "BT_ON", > - "WL_ON", > - "STATUS_LED_R", > - "LAN_RUN", > - "", > - "CAM_GPIO0", > - "CAM_GPIO1", > - ""; > - status = "okay"; > - }; > -}; > - > -&gpio { > - /* > - * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and > - * the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD1", > - "RXD1", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "HDMI_HPD_N", > - "STATUS_LED_G", > - /* Used by BT module */ > - "CTS0", > - "RTS0", > - "TXD0", > - "RXD0", > - /* Used by Wifi */ > - "SD1_CLK", > - "SD1_CMD", > - "SD1_DATA0", > - "SD1_DATA1", > - "SD1_DATA2", > - "SD1_DATA3", > - "PWM0_OUT", > - "PWM1_OUT", > - "ETHCLK", > - "WIFI_CLK", > - "SDA0", > - "SCL0", > - "SMPS_SCL", > - "SMPS_SDA", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > -}; > - > -&hdmi { > - hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; > - status = "okay"; > -}; > - > -/* SDHCI is used to control the SDIO for wireless */ > -&sdhci { > - #address-cells = <1>; > - #size-cells = <0>; > - pinctrl-names = "default"; > - pinctrl-0 = <&emmc_gpio34>; > - status = "okay"; > - bus-width = <4>; > - non-removable; > - mmc-pwrseq = <&wifi_pwrseq>; > - > - brcmf: wifi@1 { > - reg = <1>; > - compatible = "brcm,bcm4329-fmac"; > - }; > -}; > - > -/* SDHOST is used to drive the SD card */ > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - status = "okay"; > - bus-width = <4>; > -}; > - > -/* uart0 communicates with the BT module */ > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; > - status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <2000000>; > - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; > - }; > -}; > - > -/* uart1 is mapped to the pin header */ > -&uart1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart1_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts > deleted file mode 100644 > index dd4a48604097..000000000000 > --- a/arch/arm/dts/bcm2837-rpi-3-b.dts > +++ /dev/null > @@ -1,176 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2837.dtsi" > -#include "bcm2836-rpi.dtsi" > -#include "bcm283x-rpi-smsc9514.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; > - model = "Raspberry Pi 3 Model B"; > - > - chosen { > - /* 8250 auxiliary UART instead of pl011 */ > - stdout-path = "serial1:115200n8"; > - }; > - > - memory@0 { > - device_type = "memory"; > - reg = <0 0x40000000>; > - }; > - > - leds { > - led-act { > - gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>; > - }; > - }; > - > - wifi_pwrseq: wifi-pwrseq { > - compatible = "mmc-pwrseq-simple"; > - reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; > - }; > -}; > - > -&firmware { > - expgpio: gpio { > - compatible = "raspberrypi,firmware-gpio"; > - gpio-controller; > - #gpio-cells = <2>; > - gpio-line-names = "BT_ON", > - "WL_ON", > - "STATUS_LED", > - "LAN_RUN", > - "HDMI_HPD_N", > - "CAM_GPIO0", > - "CAM_GPIO1", > - "PWR_LOW_N"; > - status = "okay"; > - }; > -}; > - > -&gpio { > - /* > - * Taken from rpi_SCH_3b_1p2_reduced.pdf and > - * the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "ID_SDA", > - "ID_SCL", > - "SDA1", > - "SCL1", > - "GPIO_GCLK", > - "GPIO5", > - "GPIO6", > - "SPI_CE1_N", > - "SPI_CE0_N", > - "SPI_MISO", > - "SPI_MOSI", > - "SPI_SCLK", > - "GPIO12", > - "GPIO13", > - /* Serial port */ > - "TXD1", > - "RXD1", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "", /* GPIO 28 */ > - "LAN_RUN_BOOT", > - /* Used by BT module */ > - "CTS0", > - "RTS0", > - "TXD0", > - "RXD0", > - /* Used by Wifi */ > - "SD1_CLK", > - "SD1_CMD", > - "SD1_DATA0", > - "SD1_DATA1", > - "SD1_DATA2", > - "SD1_DATA3", > - "PWM0_OUT", > - "PWM1_OUT", > - "ETHCLK", > - "WIFI_CLK", > - "SDA0", > - "SCL0", > - "SMPS_SCL", > - "SMPS_SDA", > - /* Used by SD Card */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > -}; > - > -&pwm { > - pinctrl-names = "default"; > - pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; > - status = "okay"; > -}; > - > -&hdmi { > - hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -/* uart0 communicates with the BT module */ > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>; > - status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <2000000>; > - shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; > - }; > -}; > - > -/* uart1 is mapped to the pin header */ > -&uart1 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart1_gpio14>; > - status = "okay"; > -}; > - > -/* SDHCI is used to control the SDIO for wireless */ > -&sdhci { > - #address-cells = <1>; > - #size-cells = <0>; > - pinctrl-names = "default"; > - pinctrl-0 = <&emmc_gpio34>; > - status = "okay"; > - bus-width = <4>; > - non-removable; > - mmc-pwrseq = <&wifi_pwrseq>; > - > - brcmf: wifi@1 { > - reg = <1>; > - compatible = "brcm,bcm4329-fmac"; > - }; > -}; > - > -/* SDHOST is used to drive the SD card */ > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - status = "okay"; > - bus-width = <4>; > -}; > diff --git a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts > deleted file mode 100644 > index 588d9411ceb6..000000000000 > --- a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts > +++ /dev/null > @@ -1,96 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2837-rpi-cm3.dtsi" > -#include "bcm283x-rpi-usb-host.dtsi" > - > -/ { > - compatible = "raspberrypi,3-compute-module", "brcm,bcm2837"; > - model = "Raspberry Pi Compute Module 3 IO board V3.0"; > -}; > - > -&gpio { > - /* > - * This is based on the official GPU firmware DT blob. > - * > - * Legend: > - * "NC" = not connected (no rail from the SoC) > - * "FOO" = GPIO line named "FOO" on the schematic > - * "FOO_N" = GPIO line named "FOO" on schematic, active low > - */ > - gpio-line-names = "GPIO0", > - "GPIO1", > - "GPIO2", > - "GPIO3", > - "GPIO4", > - "GPIO5", > - "GPIO6", > - "GPIO7", > - "GPIO8", > - "GPIO9", > - "GPIO10", > - "GPIO11", > - "GPIO12", > - "GPIO13", > - "GPIO14", > - "GPIO15", > - "GPIO16", > - "GPIO17", > - "GPIO18", > - "GPIO19", > - "GPIO20", > - "GPIO21", > - "GPIO22", > - "GPIO23", > - "GPIO24", > - "GPIO25", > - "GPIO26", > - "GPIO27", > - "GPIO28", > - "GPIO29", > - "GPIO30", > - "GPIO31", > - "GPIO32", > - "GPIO33", > - "GPIO34", > - "GPIO35", > - "GPIO36", > - "GPIO37", > - "GPIO38", > - "GPIO39", > - "GPIO40", > - "GPIO41", > - "GPIO42", > - "GPIO43", > - "GPIO44", > - "GPIO45", > - "GPIO46", > - "GPIO47", > - /* Used by eMMC */ > - "SD_CLK_R", > - "SD_CMD_R", > - "SD_DATA0_R", > - "SD_DATA1_R", > - "SD_DATA2_R", > - "SD_DATA3_R"; > - > - pinctrl-0 = <&gpioout &alt0>; > -}; > - > -&hdmi { > - hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; > - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; > - status = "okay"; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - status = "okay"; > -}; > - > -&uart0 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart0_gpio14>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/dts/bcm2837-rpi-cm3.dtsi > deleted file mode 100644 > index 828a20561b96..000000000000 > --- a/arch/arm/dts/bcm2837-rpi-cm3.dtsi > +++ /dev/null > @@ -1,61 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/dts-v1/; > -#include "bcm2837.dtsi" > -#include "bcm2836-rpi.dtsi" > - > -/ { > - memory@0 { > - device_type = "memory"; > - reg = <0 0x40000000>; > - }; > - > - leds { > - /* > - * Since there is no upstream GPIO driver yet, > - * remove the incomplete node. > - */ > - /delete-node/ led-act; > - }; > - > - reg_3v3: fixed-regulator { > - compatible = "regulator-fixed"; > - regulator-name = "3V3"; > - regulator-min-microvolt = <3300000>; > - regulator-max-microvolt = <3300000>; > - regulator-always-on; > - }; > - > - reg_1v8: fixed-regulator { > - compatible = "regulator-fixed"; > - regulator-name = "1V8"; > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <1800000>; > - regulator-always-on; > - }; > -}; > - > -&firmware { > - expgpio: gpio { > - compatible = "raspberrypi,firmware-gpio"; > - gpio-controller; > - #gpio-cells = <2>; > - gpio-line-names = "HDMI_HPD_N", > - "EMMC_EN_N", > - "NC", > - "NC", > - "NC", > - "NC", > - "NC", > - "NC"; > - status = "okay"; > - }; > -}; > - > -&sdhost { > - pinctrl-names = "default"; > - pinctrl-0 = <&sdhost_gpio48>; > - bus-width = <4>; > - vmmc-supply = <®_3v3>; > - vqmmc-supply = <®_1v8>; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi > deleted file mode 100644 > index 0199ec98cd61..000000000000 > --- a/arch/arm/dts/bcm2837.dtsi > +++ /dev/null > @@ -1,95 +0,0 @@ > -#include "bcm283x.dtsi" > -#include "bcm2835-common.dtsi" > -#include "bcm2835-rpi-common.dtsi" > - > -/ { > - compatible = "brcm,bcm2837"; > - > - soc { > - ranges = <0x7e000000 0x3f000000 0x1000000>, > - <0x40000000 0x40000000 0x00001000>; > - dma-ranges = <0xc0000000 0x00000000 0x3f000000>; > - > - local_intc: local_intc@40000000 { > - compatible = "brcm,bcm2836-l1-intc"; > - reg = <0x40000000 0x100>; > - interrupt-controller; > - #interrupt-cells = <2>; > - interrupt-parent = <&local_intc>; > - }; > - }; > - > - arm-pmu { > - compatible = "arm,cortex-a53-pmu"; > - interrupt-parent = <&local_intc>; > - interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; > - }; > - > - timer { > - compatible = "arm,armv7-timer"; > - interrupt-parent = <&local_intc>; > - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI > - <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI > - <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI > - <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI > - always-on; > - }; > - > - cpus: cpus { > - #address-cells = <1>; > - #size-cells = <0>; > - enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit > - > - cpu0: cpu@0 { > - device_type = "cpu"; > - compatible = "arm,cortex-a53"; > - reg = <0>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000d8>; > - }; > - > - cpu1: cpu@1 { > - device_type = "cpu"; > - compatible = "arm,cortex-a53"; > - reg = <1>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000e0>; > - }; > - > - cpu2: cpu@2 { > - device_type = "cpu"; > - compatible = "arm,cortex-a53"; > - reg = <2>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000e8>; > - }; > - > - cpu3: cpu@3 { > - device_type = "cpu"; > - compatible = "arm,cortex-a53"; > - reg = <3>; > - enable-method = "spin-table"; > - cpu-release-addr = <0x0 0x000000f0>; > - }; > - }; > -}; > - > -/* Make the BCM2835-style global interrupt controller be a child of the > - * CPU-local interrupt controller. > - */ > -&intc { > - compatible = "brcm,bcm2836-armctrl-ic"; > - reg = <0x7e00b200 0x200>; > - interrupt-parent = <&local_intc>; > - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; > -}; > - > -&cpu_thermal { > - coefficients = <(-538) 412000>; > -}; > - > -/* enable thermal sensor with the correct compatible property set */ > -&thermal { > - compatible = "brcm,bcm2837-thermal"; > - status = "okay"; > -}; > diff --git a/arch/arm/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/dts/bcm283x-rpi-lan7515.dtsi > deleted file mode 100644 > index 70bece63f9a7..000000000000 > --- a/arch/arm/dts/bcm283x-rpi-lan7515.dtsi > +++ /dev/null > @@ -1,41 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -#include <dt-bindings/net/microchip-lan78xx.h> > - > -/ { > - aliases { > - ethernet0 = ðernet; > - }; > -}; > - > -&usb { > - usb-port@1 { > - compatible = "usb424,2514"; > - reg = <1>; > - #address-cells = <1>; > - #size-cells = <0>; > - > - usb-port@1 { > - compatible = "usb424,2514"; > - reg = <1>; > - #address-cells = <1>; > - #size-cells = <0>; > - > - ethernet: ethernet@1 { > - compatible = "usb424,7800"; > - reg = <1>; > - > - mdio { > - #address-cells = <0x1>; > - #size-cells = <0x0>; > - eth_phy: ethernet-phy@1 { > - reg = <1>; > - microchip,led-modes = < > - LAN78XX_LINK_1000_ACTIVITY > - LAN78XX_LINK_10_100_ACTIVITY > - >; > - }; > - }; > - }; > - }; > - }; > -}; > diff --git a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi > deleted file mode 100644 > index 967e081cb9c2..000000000000 > --- a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi > +++ /dev/null > @@ -1,20 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -/ { > - aliases { > - ethernet0 = ðernet; > - }; > -}; > - > -&usb { > - usb1@1 { > - compatible = "usb424,9512"; > - reg = <1>; > - #address-cells = <1>; > - #size-cells = <0>; > - > - ethernet: usbether@1 { > - compatible = "usb424,ec00"; > - reg = <1>; > - }; > - }; > -}; > diff --git a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi > deleted file mode 100644 > index dc7ae776db5f..000000000000 > --- a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi > +++ /dev/null > @@ -1,19 +0,0 @@ > -/ { > - aliases { > - ethernet0 = ðernet; > - }; > -}; > - > -&usb { > - usb1@1 { > - compatible = "usb424,9514"; > - reg = <1>; > - #address-cells = <1>; > - #size-cells = <0>; > - > - ethernet: usbether@1 { > - compatible = "usb424,ec00"; > - reg = <1>; > - }; > - }; > -}; > diff --git a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi > deleted file mode 100644 > index 73f4ece8dcd0..000000000000 > --- a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi > +++ /dev/null > @@ -1,3 +0,0 @@ > -&usb { > - dr_mode = "host"; > -}; > diff --git a/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi b/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi > deleted file mode 100644 > index e2fd9610e125..000000000000 > --- a/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi > +++ /dev/null > @@ -1,11 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -&usb { > - dr_mode = "otg"; > - g-rx-fifo-size = <256>; > - g-np-tx-fifo-size = <32>; > - /* > - * According to dwc2 the sum of all device EP > - * fifo sizes shouldn't exceed 3776 bytes. > - */ > - g-tx-fifo-size = <256 256 512 512 512 768 768>; > -}; > diff --git a/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi > deleted file mode 100644 > index 0ff0e9e25327..000000000000 > --- a/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi > +++ /dev/null > @@ -1,7 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0 > -&usb { > - dr_mode = "peripheral"; > - g-rx-fifo-size = <256>; > - g-np-tx-fifo-size = <32>; > - g-tx-fifo-size = <256 256 512 512 512 768 768>; > -}; > diff --git a/arch/arm/dts/bcm283x-u-boot.dtsi b/arch/arm/dts/bcm283x-u-boot.dtsi > deleted file mode 100644 > index ec0f93dd8507..000000000000 > --- a/arch/arm/dts/bcm283x-u-boot.dtsi > +++ /dev/null > @@ -1,29 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * U-Boot addition to keep baudrate set by firmware > - * and also initialize before relocation. > - * > - * (C) Copyright 2016 Fabian Vogt <fvogt@suse.com> > - */ > - > -&uart0 { > - skip-init; > - bootph-all; > -}; > - > -&uart1 { > - skip-init; > - bootph-all; > -}; > - > -&gpio { > - bootph-all; > -}; > - > -&uart0_gpio14 { > - bootph-all; > -}; > - > -&uart1_gpio14 { > - bootph-all; > -}; > diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi > deleted file mode 100644 > index a3e06b680947..000000000000 > --- a/arch/arm/dts/bcm283x.dtsi > +++ /dev/null > @@ -1,501 +0,0 @@ > -#include <dt-bindings/pinctrl/bcm2835.h> > -#include <dt-bindings/clock/bcm2835.h> > -#include <dt-bindings/clock/bcm2835-aux.h> > -#include <dt-bindings/gpio/gpio.h> > -#include <dt-bindings/interrupt-controller/irq.h> > -#include <dt-bindings/soc/bcm2835-pm.h> > - > -/* firmware-provided startup stubs live here, where the secondary CPUs are > - * spinning. > - */ > -/memreserve/ 0x00000000 0x00001000; > - > -/* This include file covers the common peripherals and configuration between > - * bcm2835 and bcm2836 implementations, leaving the CPU configuration to > - * bcm2835.dtsi and bcm2836.dtsi. > - */ > - > -/ { > - compatible = "brcm,bcm2835"; > - model = "BCM2835"; > - #address-cells = <1>; > - #size-cells = <1>; > - > - aliases { > - serial0 = &uart0; > - serial1 = &uart1; > - }; > - > - chosen { > - stdout-path = "serial0:115200n8"; > - }; > - > - rmem: reserved-memory { > - #address-cells = <1>; > - #size-cells = <1>; > - ranges; > - > - cma: linux,cma { > - compatible = "shared-dma-pool"; > - size = <0x4000000>; /* 64MB */ > - reusable; > - linux,cma-default; > - }; > - }; > - > - thermal-zones { > - cpu_thermal: cpu-thermal { > - polling-delay-passive = <0>; > - polling-delay = <1000>; > - > - trips { > - cpu-crit { > - temperature = <90000>; > - hysteresis = <0>; > - type = "critical"; > - }; > - }; > - > - cooling-maps { > - }; > - }; > - }; > - > - soc { > - compatible = "simple-bus"; > - #address-cells = <1>; > - #size-cells = <1>; > - > - system_timer: timer@7e003000 { > - compatible = "brcm,bcm2835-system-timer"; > - reg = <0x7e003000 0x1000>; > - interrupts = <1 0>, <1 1>, <1 2>, <1 3>; > - /* This could be a reference to BCM2835_CLOCK_TIMER, > - * but we don't have the driver using the common clock > - * support yet. > - */ > - clock-frequency = <1000000>; > - }; > - > - txp: txp@7e004000 { > - compatible = "brcm,bcm2835-txp"; > - reg = <0x7e004000 0x20>; > - interrupts = <1 11>; > - }; > - > - clocks: cprman@7e101000 { > - compatible = "brcm,bcm2835-cprman"; > - #clock-cells = <1>; > - reg = <0x7e101000 0x2000>; > - > - /* CPRMAN derives almost everything from the > - * platform's oscillator. However, the DSI > - * pixel clocks come from the DSI analog PHY. > - */ > - clocks = <&clk_osc>, > - <&dsi0 0>, <&dsi0 1>, <&dsi0 2>, > - <&dsi1 0>, <&dsi1 1>, <&dsi1 2>; > - }; > - > - mailbox: mailbox@7e00b880 { > - compatible = "brcm,bcm2835-mbox"; > - reg = <0x7e00b880 0x40>; > - interrupts = <0 1>; > - #mbox-cells = <0>; > - }; > - > - gpio: gpio@7e200000 { > - compatible = "brcm,bcm2835-gpio"; > - reg = <0x7e200000 0xb4>; > - /* > - * The GPIO IP block is designed for 3 banks of GPIOs. > - * Each bank has a GPIO interrupt for itself. > - * There is an overall "any bank" interrupt. > - * In order, these are GIC interrupts 17, 18, 19, 20. > - * Since the BCM2835 only has 2 banks, the 2nd bank > - * interrupt output appears to be mirrored onto the > - * 3rd bank's interrupt signal. > - * So, a bank0 interrupt shows up on 17, 20, and > - * a bank1 interrupt shows up on 18, 19, 20! > - */ > - interrupts = <2 17>, <2 18>, <2 19>, <2 20>; > - > - gpio-controller; > - #gpio-cells = <2>; > - > - interrupt-controller; > - #interrupt-cells = <2>; > - > - /* Defines common pin muxing groups > - * > - * While each pin can have its mux selected > - * for various functions individually, some > - * groups only make sense to switch to a > - * particular function together. > - */ > - dpi_gpio0: dpi_gpio0 { > - brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 > - 12 13 14 15 16 17 18 19 > - 20 21 22 23 24 25 26 27>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > - emmc_gpio22: emmc_gpio22 { > - brcm,pins = <22 23 24 25 26 27>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - }; > - emmc_gpio34: emmc_gpio34 { > - brcm,pins = <34 35 36 37 38 39>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - brcm,pull = <BCM2835_PUD_OFF > - BCM2835_PUD_UP > - BCM2835_PUD_UP > - BCM2835_PUD_UP > - BCM2835_PUD_UP > - BCM2835_PUD_UP>; > - }; > - emmc_gpio48: emmc_gpio48 { > - brcm,pins = <48 49 50 51 52 53>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - }; > - > - gpclk0_gpio4: gpclk0_gpio4 { > - brcm,pins = <4>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - gpclk1_gpio5: gpclk1_gpio5 { > - brcm,pins = <5>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - gpclk1_gpio42: gpclk1_gpio42 { > - brcm,pins = <42>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - gpclk1_gpio44: gpclk1_gpio44 { > - brcm,pins = <44>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - gpclk2_gpio6: gpclk2_gpio6 { > - brcm,pins = <6>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - gpclk2_gpio43: gpclk2_gpio43 { > - brcm,pins = <43>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - brcm,pull = <BCM2835_PUD_OFF>; > - }; > - > - i2c0_gpio0: i2c0_gpio0 { > - brcm,pins = <0 1>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - i2c0_gpio28: i2c0_gpio28 { > - brcm,pins = <28 29>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - i2c0_gpio44: i2c0_gpio44 { > - brcm,pins = <44 45>; > - brcm,function = <BCM2835_FSEL_ALT1>; > - }; > - i2c1_gpio2: i2c1_gpio2 { > - brcm,pins = <2 3>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - i2c1_gpio44: i2c1_gpio44 { > - brcm,pins = <44 45>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > - > - jtag_gpio22: jtag_gpio22 { > - brcm,pins = <22 23 24 25 26 27>; > - brcm,function = <BCM2835_FSEL_ALT4>; > - }; > - > - pcm_gpio18: pcm_gpio18 { > - brcm,pins = <18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - pcm_gpio28: pcm_gpio28 { > - brcm,pins = <28 29 30 31>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > - > - sdhost_gpio48: sdhost_gpio48 { > - brcm,pins = <48 49 50 51 52 53>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - > - spi0_gpio7: spi0_gpio7 { > - brcm,pins = <7 8 9 10 11>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - spi0_gpio35: spi0_gpio35 { > - brcm,pins = <35 36 37 38 39>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - spi1_gpio16: spi1_gpio16 { > - brcm,pins = <16 17 18 19 20 21>; > - brcm,function = <BCM2835_FSEL_ALT4>; > - }; > - spi2_gpio40: spi2_gpio40 { > - brcm,pins = <40 41 42 43 44 45>; > - brcm,function = <BCM2835_FSEL_ALT4>; > - }; > - > - uart0_gpio14: uart0_gpio14 { > - brcm,pins = <14 15>; > - brcm,function = <BCM2835_FSEL_ALT0>; > - }; > - /* Separate from the uart0_gpio14 group > - * because it conflicts with spi1_gpio16, and > - * people often run uart0 on the two pins > - * without flow control. > - */ > - uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 { > - brcm,pins = <16 17>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - }; > - uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 { > - brcm,pins = <30 31>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>; > - }; > - uart0_gpio32: uart0_gpio32 { > - brcm,pins = <32 33>; > - brcm,function = <BCM2835_FSEL_ALT3>; > - brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>; > - }; > - uart0_gpio36: uart0_gpio36 { > - brcm,pins = <36 37>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > - uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 { > - brcm,pins = <38 39>; > - brcm,function = <BCM2835_FSEL_ALT2>; > - }; > - > - uart1_gpio14: uart1_gpio14 { > - brcm,pins = <14 15>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 { > - brcm,pins = <16 17>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - uart1_gpio32: uart1_gpio32 { > - brcm,pins = <32 33>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 { > - brcm,pins = <30 31>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - uart1_gpio40: uart1_gpio40 { > - brcm,pins = <40 41>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 { > - brcm,pins = <42 43>; > - brcm,function = <BCM2835_FSEL_ALT5>; > - }; > - }; > - > - uart0: serial@7e201000 { > - compatible = "arm,pl011", "arm,primecell"; > - reg = <0x7e201000 0x200>; > - interrupts = <2 25>; > - clocks = <&clocks BCM2835_CLOCK_UART>, > - <&clocks BCM2835_CLOCK_VPU>; > - clock-names = "uartclk", "apb_pclk"; > - arm,primecell-periphid = <0x00241011>; > - }; > - > - sdhost: mmc@7e202000 { > - compatible = "brcm,bcm2835-sdhost"; > - reg = <0x7e202000 0x100>; > - interrupts = <2 24>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - status = "disabled"; > - }; > - > - i2s: i2s@7e203000 { > - compatible = "brcm,bcm2835-i2s"; > - reg = <0x7e203000 0x24>; > - clocks = <&clocks BCM2835_CLOCK_PCM>; > - status = "disabled"; > - }; > - > - spi: spi@7e204000 { > - compatible = "brcm,bcm2835-spi"; > - reg = <0x7e204000 0x200>; > - interrupts = <2 22>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - i2c0: i2c@7e205000 { > - compatible = "brcm,bcm2835-i2c"; > - reg = <0x7e205000 0x200>; > - interrupts = <2 21>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - dpi: dpi@7e208000 { > - compatible = "brcm,bcm2835-dpi"; > - reg = <0x7e208000 0x8c>; > - clocks = <&clocks BCM2835_CLOCK_VPU>, > - <&clocks BCM2835_CLOCK_DPI>; > - clock-names = "core", "pixel"; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - dsi0: dsi@7e209000 { > - compatible = "brcm,bcm2835-dsi0"; > - reg = <0x7e209000 0x78>; > - interrupts = <2 4>; > - #address-cells = <1>; > - #size-cells = <0>; > - #clock-cells = <1>; > - > - clocks = <&clocks BCM2835_PLLA_DSI0>, > - <&clocks BCM2835_CLOCK_DSI0E>, > - <&clocks BCM2835_CLOCK_DSI0P>; > - clock-names = "phy", "escape", "pixel"; > - > - clock-output-names = "dsi0_byte", > - "dsi0_ddr2", > - "dsi0_ddr"; > - > - status = "disabled"; > - }; > - > - aux: aux@7e215000 { > - compatible = "brcm,bcm2835-aux"; > - #clock-cells = <1>; > - reg = <0x7e215000 0x8>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - }; > - > - uart1: serial@7e215040 { > - compatible = "brcm,bcm2835-aux-uart"; > - reg = <0x7e215040 0x40>; > - interrupts = <1 29>; > - clocks = <&aux BCM2835_AUX_CLOCK_UART>; > - status = "disabled"; > - }; > - > - spi1: spi@7e215080 { > - compatible = "brcm,bcm2835-aux-spi"; > - reg = <0x7e215080 0x40>; > - interrupts = <1 29>; > - clocks = <&aux BCM2835_AUX_CLOCK_SPI1>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - spi2: spi@7e2150c0 { > - compatible = "brcm,bcm2835-aux-spi"; > - reg = <0x7e2150c0 0x40>; > - interrupts = <1 29>; > - clocks = <&aux BCM2835_AUX_CLOCK_SPI2>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - pwm: pwm@7e20c000 { > - compatible = "brcm,bcm2835-pwm"; > - reg = <0x7e20c000 0x28>; > - clocks = <&clocks BCM2835_CLOCK_PWM>; > - assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; > - assigned-clock-rates = <10000000>; > - #pwm-cells = <2>; > - status = "disabled"; > - }; > - > - sdhci: mmc@7e300000 { > - compatible = "brcm,bcm2835-sdhci"; > - reg = <0x7e300000 0x100>; > - interrupts = <2 30>; > - clocks = <&clocks BCM2835_CLOCK_EMMC>; > - status = "disabled"; > - }; > - > - hvs@7e400000 { > - compatible = "brcm,bcm2835-hvs"; > - reg = <0x7e400000 0x6000>; > - interrupts = <2 1>; > - }; > - > - dsi1: dsi@7e700000 { > - compatible = "brcm,bcm2835-dsi1"; > - reg = <0x7e700000 0x8c>; > - interrupts = <2 12>; > - #address-cells = <1>; > - #size-cells = <0>; > - #clock-cells = <1>; > - > - clocks = <&clocks BCM2835_PLLD_DSI1>, > - <&clocks BCM2835_CLOCK_DSI1E>, > - <&clocks BCM2835_CLOCK_DSI1P>; > - clock-names = "phy", "escape", "pixel"; > - > - clock-output-names = "dsi1_byte", > - "dsi1_ddr2", > - "dsi1_ddr"; > - > - status = "disabled"; > - }; > - > - i2c1: i2c@7e804000 { > - compatible = "brcm,bcm2835-i2c"; > - reg = <0x7e804000 0x1000>; > - interrupts = <2 21>; > - clocks = <&clocks BCM2835_CLOCK_VPU>; > - #address-cells = <1>; > - #size-cells = <0>; > - status = "disabled"; > - }; > - > - usb: usb@7e980000 { > - compatible = "brcm,bcm2835-usb"; > - reg = <0x7e980000 0x10000>; > - interrupts = <1 9>; > - #address-cells = <1>; > - #size-cells = <0>; > - clocks = <&clk_usb>; > - clock-names = "otg"; > - phys = <&usbphy>; > - phy-names = "usb2-phy"; > - }; > - }; > - > - clocks { > - /* The oscillator is the root of the clock tree. */ > - clk_osc: clk-osc { > - compatible = "fixed-clock"; > - #clock-cells = <0>; > - clock-output-names = "osc"; > - clock-frequency = <19200000>; > - }; > - > - clk_usb: clk-usb { > - compatible = "fixed-clock"; > - #clock-cells = <0>; > - clock-output-names = "otg"; > - clock-frequency = <480000000>; > - }; > - }; > - > - usbphy: phy { > - compatible = "usb-nop-xceiv"; > - #phy-cells = <0>; > - }; > -}; > diff --git a/arch/arm/dts/bcm7xxx.dts b/arch/arm/dts/bcm7xxx.dts > deleted file mode 100644 > index 786ce3ff9597..000000000000 > --- a/arch/arm/dts/bcm7xxx.dts > +++ /dev/null > @@ -1,15 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * Empty devicetre file for bcm7260 board > - * > - * This is required to make the board build with CONFIG OF_SEPARATE > - * In-tree document explains how to obtain a real devicetree using 'bolt' but > - * I did not attempt this. > - * > - * Copyright 2021 Google LLC > - */ > - > -/dts-v1/; > - > -/ { > -}; > diff --git a/arch/arm/dts/highbank.dts b/arch/arm/dts/highbank.dts > deleted file mode 100644 > index 1480bad91040..000000000000 > --- a/arch/arm/dts/highbank.dts > +++ /dev/null > @@ -1,9 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0-only > -/* > - * Empty devicetree for highbank/midway > - */ > - > -/dts-v1/; > - > -/ { > -}; > diff --git a/arch/arm/dts/octeontx.dts b/arch/arm/dts/octeontx.dts > deleted file mode 100644 > index 60a15f5df23f..000000000000 > --- a/arch/arm/dts/octeontx.dts > +++ /dev/null > @@ -1,14 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * Dummy devicetre file for octeontx2 boards > - * > - * This is required to make the board build with CONFIG OF_SEPARATE > - * I could not find any in-tree documentation at all so this is a dummy file. > - * > - * Copyright 2021 Google LLC > - */ > - > -/dts-v1/; > - > -/ { > -}; > diff --git a/arch/arm/dts/qemu-arm.dts b/arch/arm/dts/qemu-arm.dts > deleted file mode 100644 > index 230c630f04fd..000000000000 > --- a/arch/arm/dts/qemu-arm.dts > +++ /dev/null > @@ -1,11 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ OR MIT > -/* > - * Empty device tree for qemu_arm > - > - * Copyright 2021 Google LLC > - */ > - > -/dts-v1/; > - > -/ { > -}; > diff --git a/arch/arm/dts/xenguest-arm64.dts b/arch/arm/dts/xenguest-arm64.dts > deleted file mode 100644 > index d8734433763c..000000000000 > --- a/arch/arm/dts/xenguest-arm64.dts > +++ /dev/null > @@ -1,15 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * Empty devicetree file for xenguest_arm64 > - * > - * This is required to make the board build with CONFIG OF_SEPARATE > - * Build instructions at xenguest_arm64.rst are inadequate for obtaining a real > - * devicetree. > - * > - * Copyright 2021 Google LLC > - */ > - > -/dts-v1/; > - > -/ { > -}; > -- > 2.43.0 > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini ` (4 preceding siblings ...) 2026-08-24 19:48 ` [PATCH v2 5/5] arm: Drop unused dts files Tom Rini @ 2026-08-25 16:36 ` Yao Zi 2026-09-04 1:30 ` Tom Rini 6 siblings, 0 replies; 9+ messages in thread From: Yao Zi @ 2026-08-25 16:36 UTC (permalink / raw) To: Tom Rini, u-boot; +Cc: Yao Zi On Mon, Aug 24, 2026 at 01:48:44PM -0600, Tom Rini wrote: > Hey all, > > This series depends on the series to correct the logic around > BLOBLIST_PASSAGE_MANDATORY and found at > https://lore.kernel.org/r/20260824194814.555634-1-trini@konsulko.com/ > > In this series we correct how we handle OF_OMIT_DTB so that we can in > turn not have an empty or fake dts file in the tree, when we are > building for the case where we would be omitting building the final part > of the dtb for use anyhow. With the changes in the previous series, we > can then correct the Kconfig logic around OF_OMIT_DTB and > DEFAULT_DEVICE_TREE so that when we're omitting the device tree binary > we don't try and build one anyhow. Finally, we can remove all of the > empty / fake device tree sources we have, or in some cases have but > never used. > > Changes in v2: > - Split the previous series in two. No actual changes made. For Makefile and Kconfig changes, Reviewed-by: Yao Zi <me@ziyao.cc> > -- > Tom > Best regards, Yao Zi ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini ` (5 preceding siblings ...) 2026-08-25 16:36 ` [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless " Yao Zi @ 2026-09-04 1:30 ` Tom Rini 6 siblings, 0 replies; 9+ messages in thread From: Tom Rini @ 2026-09-04 1:30 UTC (permalink / raw) To: u-boot, Tom Rini On Mon, 24 Aug 2026 13:48:44 -0600, Tom Rini wrote: > Hey all, > > This series depends on the series to correct the logic around > BLOBLIST_PASSAGE_MANDATORY and found at > https://lore.kernel.org/r/20260824194814.555634-1-trini@konsulko.com/ > > In this series we correct how we handle OF_OMIT_DTB so that we can in > turn not have an empty or fake dts file in the tree, when we are > building for the case where we would be omitting building the final part > of the dtb for use anyhow. With the changes in the previous series, we > can then correct the Kconfig logic around OF_OMIT_DTB and > DEFAULT_DEVICE_TREE so that when we're omitting the device tree binary > we don't try and build one anyhow. Finally, we can remove all of the > empty / fake device tree sources we have, or in some cases have but > never used. > > [...] Applied to u-boot/next, thanks! [1/5] dts: Correct behavior of OF_OMIT_DTB commit: b9cd57c5cefab330ec91e9c5143470c2811ef87a [2/5] dts: Make DEFAULT_DEVICE_TREE depend on !OF_OMIT_DTB commit: ad14691f3e5029ff09ffccfa76f9893f5f2a6a30 [3/5] dts: Correct entry for OF_OMIT_DTB commit: 68e65953400f1d4fc594f20e834fd2f78b100562 [4/5] powerpc: drop qemu-ppce500 dts commit: 9012579179f78f82b3fdaff5c9029be97739fcf2 [5/5] arm: Drop unused dts files commit: 99df7f47155100ff0fc83f5671ab5064a72d3e5d -- Tom ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2026-09-04 1:30 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2026-08-24 19:48 [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless dts files Tom Rini 2026-08-24 19:48 ` [PATCH v2 1/5] dts: Correct behavior of OF_OMIT_DTB Tom Rini 2026-08-24 19:48 ` [PATCH v2 2/5] dts: Make DEFAULT_DEVICE_TREE depend on !OF_OMIT_DTB Tom Rini 2026-08-24 19:48 ` [PATCH v2 3/5] dts: Correct entry for OF_OMIT_DTB Tom Rini 2026-08-24 19:48 ` [PATCH v2 4/5] powerpc: drop qemu-ppce500 dts Tom Rini 2026-08-24 19:48 ` [PATCH v2 5/5] arm: Drop unused dts files Tom Rini 2026-08-24 20:09 ` Peter Robinson 2026-08-25 16:36 ` [PATCH v2 0/5] Fix logic of OF_OMIT_DTB and remove useless " Yao Zi 2026-09-04 1:30 ` Tom Rini
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.