[PATCH] wifi: brcmfmac: log the firmware status when a connect fails

[PATCH] wifi: brcmfmac: log the firmware status when a connect fails

[Ryohei Hashimoto]

brcmf_bss_connect_done() receives the firmware event in @e but discards it
on the failure path.  Every failed connect is reported to cfg80211 as
WLAN_STATUS_AUTH_TIMEOUT (16), whatever the firmware actually said, so
userspace only ever sees:

  wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:00:00:00:00:00 status_code=16

The all-zero BSSID comes from the same place: conn_params is memset to
zero and profile->bssid has not been filled in when the station never
associated.

status_code=16 therefore carries no information about the cause.  It is not
an AP response and it does not mean "authentication timed out" - it is the
only failure value this driver can produce.  This is a recurring source of
confusion: [1] has been open since 2023 with more than twenty follow-ups
and no explanation of the code, and covers BCM4345/6, BCM43430 and
CYW43455 across several kernel versions.  It supersedes [2], filed against
the firmware repository a day earlier and closed in favour of it.

The firmware's own status (BRCMF_E_STATUS_*) is more specific - FAIL,
TIMEOUT, NO_NETWORKS, ABORT and so on - and it is already in hand.  Log it
so the cause can be narrowed down without rebuilding the kernel.

brcmf_err() is used rather than brcmf_dbg() or brcmf_info() because it is
the only one of the three that is both visible in a distribution kernel and
bounded.  brcmf_dbg(CONN) is compiled out without CONFIG_BRCMDBG, which is
what makes the reports in [1] and [2] impossible to act on - the people
hitting this run stock kernels.  brcmf_info() expands to a plain pr_info()
in a non-debug build and is not rate limited, and wpa_supplicant retries
the association every few seconds, so it would flood the log.  brcmf_err()
goes through net_ratelimit() there, so a station retrying against an
unreachable AP prints at most a few lines per second.

All three fields are printed because only some of them are meaningful on
each path into the failure branch.  brcmf_is_nonetwork() keys off @status,
so that is the useful field for a join that never associated - the case in
[1].  brcmf_is_linkdown() keys off @event_code and the 802.11 @reason and
does not look at @status at all, so @status can read 0 there.  Printing the
three together lets the reader tell which path was taken instead of
guessing from one number.

The status reported to cfg80211 is left alone; changing it would alter what
userspace sees.

[1] https://github.com/RPi-Distro/firmware-nonfree/issues/38
[2] https://github.com/raspberrypi/firmware/issues/1829

Signed-off-by: Ryohei Hashimoto <laurel.medalist12@gmail.com>
---
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
index 872c488..114dabb 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
@@ -6522,6 +6522,8 @@ brcmf_bss_connect_done(struct brcmf_cfg80211_info *cfg,
 			clear_bit(BRCMF_VIF_STATUS_ASSOC_SUCCESS,
 				  &ifp->vif->sme_state);
 			conn_params.status = WLAN_STATUS_AUTH_TIMEOUT;
+			brcmf_err("connect failed: event %u status %u reason %u\n",
+				  e->event_code, e->status, e->reason);
 		}
 		conn_params.links[0].bssid = profile->bssid;
 		conn_params.req_ie = conn_info->req_ie;