[PATCH net-next v5 09/11] net: stmmac: dwmac-rk: add SGMII support for RK3568

[Coia Prant <coiaprant@gmail.com>]

The RK3568 SoC integrates a Synopsys DesignWare XPCS that can be
connected to GMAC0 or GMAC1 in SGMII mode.  Add the necessary glue
logic to support this configuration.

The current dwmac-rk driver does not support SGMII mode.  SGMII
requires a PCS to handle auto-negotiation and link state reporting,
but the existing driver only supports RGMII and RMII.

Add a set_to_sgmii() callback to configure the GMAC GRF register for
SGMII mode (bit 7 set, interface selection bits 4:6 ignored when set).
Also add a set_to_rmii() callback for rk3568 to explicitly clear bit 7,
since the new SGMII path leaves it set and the RMII branch previously
relied on the SoC reset value.

Provide pcs_init/pcs_exit callbacks to create/destroy the XPCS via
xpcs_rk_create() from the Rockchip XPCS platform driver, and a
select_pcs callback to return the XPCS to phylink.

Reorder rk_gmac_powerup() so that gmac_clk_enable() is called before
the SGMII check.  The SGMII path skips rk_get_phy_intf_sel(), so the
clock must be enabled earlier to cover all register accesses in that
path.  While at it, unify the error unwinding into a single
clk_disable label and add error handling for the default (unhandled
interface) case.

SGMII In-band vs Out-of-band
============================
On RK3568, the MAC clock is fixed at 125 MHz and cannot be dynamically
changed by the stmmac core's set_clk_tx_rate callback.  In-band mode
works because the PCS handles rate adaptation internally.  Out-of-band
mode does not work because the MAC would need to change the clock rate
to 125/12.5/1.25 MHz for 1000/100/10 Mbps respectively, and the clock
is fixed.

Enable default_an_inband for SGMII and disable the generic stmmac
set_clk_tx_rate callback.  This forces phylink to use in-band mode,
where the PCS is responsible for speed/duplex negotiation.

Note that default_an_inband can be overridden by a fixed-link node,
and phylink may also fall back to out-of-band if the PHY does not
support in-band signalling.  Out-of-band SGMII is not supported by
this driver: the MAC clock would stay at 125 MHz for 10/100 Mbps,
giving working TX but failing RX.  Boards must use in-band mode
(managed = "in-band-status" or an in-band capable PHY).

Link: https://dl.radxa.com/rock3/docs/hw/datasheet/Rockchip%20RK3568%20TRM%20Part1%20V1.1-20210301.pdf (Page 386)
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig   |   1 +
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 134 +++++++++++++++---
 2 files changed, 115 insertions(+), 20 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index e3dd5adda5aca..5088acc06982e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -170,6 +170,7 @@ config DWMAC_ROCKCHIP
 	default ARCH_ROCKCHIP
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
 	select MFD_SYSCON
+	select PCS_XPCS_ROCKCHIP
 	help
 	  Support for Ethernet controller on Rockchip RK3288 SoC.
 
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
index 8d7042e689261..5d501ed8d1429 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
@@ -20,6 +20,7 @@
 #include <linux/delay.h>
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
+#include <linux/pcs/pcs-xpcs-rk.h>
 #include <linux/pm_runtime.h>
 
 #include "stmmac_platform.h"
@@ -47,6 +48,7 @@ struct rk_gmac_ops {
 	void (*set_to_rgmii)(struct rk_priv_data *bsp_priv,
 			     int tx_delay, int rx_delay);
 	void (*set_to_rmii)(struct rk_priv_data *bsp_priv);
+	void (*set_to_sgmii)(struct rk_priv_data *bsp_priv);
 	int (*set_speed)(struct rk_priv_data *bsp_priv,
 			 phy_interface_t interface, int speed);
 	void (*integrated_phy_powerup)(struct rk_priv_data *bsp_priv);
@@ -63,6 +65,7 @@ struct rk_gmac_ops {
 	bool clock_grf_reg_in_php;
 	bool supports_rgmii;
 	bool supports_rmii;
+	bool supports_sgmii;
 	bool php_grf_required;
 	bool regs_valid;
 	u32 regs[];
@@ -98,6 +101,7 @@ struct rk_priv_data {
 	bool integrated_phy;
 	bool supports_rgmii;
 	bool supports_rmii;
+	bool supports_sgmii;
 
 	struct clk_bulk_data *clks;
 	int num_clks;
@@ -809,6 +813,8 @@ static const struct rk_gmac_ops rk3528_ops = {
 #define RK3568_GRF_GMAC1_CON1		0x038c
 
 /* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
+#define RK3568_GMAC_MODE_RMII_RGMII		GRF_CLR_BIT(7)
+#define RK3568_GMAC_MODE_SGMII_QSGMII		GRF_BIT(7)
 #define RK3568_GMAC_FLOW_CTRL			GRF_BIT(3)
 #define RK3568_GMAC_FLOW_CTRL_CLR		GRF_CLR_BIT(3)
 #define RK3568_GMAC_RXCLK_DLY_ENABLE		GRF_BIT(1)
@@ -836,6 +842,17 @@ static int rk3568_init(struct rk_priv_data *bsp_priv)
 	}
 }
 
+static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
+{
+	u32 con1;
+
+	con1 = (bsp_priv->id == 1) ? RK3568_GRF_GMAC1_CON1 :
+				     RK3568_GRF_GMAC0_CON1;
+
+	regmap_write(bsp_priv->grf, con1,
+		     RK3568_GMAC_MODE_RMII_RGMII);
+}
+
 static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
 				int tx_delay, int rx_delay)
 {
@@ -851,19 +868,31 @@ static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
 		     RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
 
 	regmap_write(bsp_priv->grf, con1,
+		     RK3568_GMAC_MODE_RMII_RGMII |
 		     RK3568_GMAC_RXCLK_DLY_ENABLE |
 		     RK3568_GMAC_TXCLK_DLY_ENABLE);
 }
 
+static void rk3568_set_to_sgmii(struct rk_priv_data *bsp_priv)
+{
+	u32 con1;
+
+	con1 = (bsp_priv->id == 1) ? RK3568_GRF_GMAC1_CON1 :
+				     RK3568_GRF_GMAC0_CON1;
+
+	regmap_write(bsp_priv->grf, con1, RK3568_GMAC_MODE_SGMII_QSGMII);
+}
+
 static const struct rk_gmac_ops rk3568_ops = {
 	.init = rk3568_init,
+	.set_to_rmii = rk3568_set_to_rmii,
 	.set_to_rgmii = rk3568_set_to_rgmii,
+	.set_to_sgmii = rk3568_set_to_sgmii,
+
 	.set_speed = rk_set_clk_mac_speed,
 
 	.gmac_phy_intf_sel_mask = GENMASK_U16(6, 4),
 
-	.supports_rmii = true,
-
 	.regs_valid = true,
 	.regs = {
 		0xfe2a0000, /* gmac0 */
@@ -1208,6 +1237,43 @@ static void rk_phy_powerdown(struct rk_priv_data *bsp_priv)
 		dev_err(bsp_priv->dev, "fail to disable phy-supply\n");
 }
 
+static int rk_pcs_init(struct stmmac_priv *priv)
+{
+	struct device_node *np = priv->device->of_node;
+	struct device_node *pcs_node;
+	struct dw_xpcs *xpcs;
+
+	pcs_node = of_parse_phandle(np, "pcs-handle", 0);
+	if (!pcs_node)
+		return -ENODEV;
+
+	xpcs = xpcs_rk_create(priv->device, pcs_node);
+	of_node_put(pcs_node);
+	if (IS_ERR(xpcs))
+		return PTR_ERR(xpcs);
+
+	priv->hw->xpcs = xpcs;
+	return 0;
+}
+
+static void rk_pcs_exit(struct stmmac_priv *priv)
+{
+	if (!priv->hw->xpcs)
+		return;
+
+	xpcs_destroy(priv->hw->xpcs);
+	priv->hw->xpcs = NULL;
+}
+
+static struct phylink_pcs *rk_select_pcs(struct stmmac_priv *priv,
+					 phy_interface_t interface)
+{
+	if (!priv->hw->xpcs)
+		return NULL;
+
+	return xpcs_to_phylink_pcs(priv->hw->xpcs);
+}
+
 static struct rk_priv_data *rk_gmac_setup(struct platform_device *pdev,
 					  struct plat_stmmacenet_data *plat,
 					  const struct rk_gmac_ops *ops)
@@ -1330,6 +1396,7 @@ static struct rk_priv_data *rk_gmac_setup(struct platform_device *pdev,
 
 	bsp_priv->supports_rgmii = ops->supports_rgmii || !!ops->set_to_rgmii;
 	bsp_priv->supports_rmii = ops->supports_rmii || !!ops->set_to_rmii;
+	bsp_priv->supports_sgmii = ops->supports_sgmii || !!ops->set_to_sgmii;
 
 	if (ops->init) {
 		ret = ops->init(bsp_priv);
@@ -1361,6 +1428,10 @@ static int rk_gmac_check_ops(struct rk_priv_data *bsp_priv)
 		if (!bsp_priv->supports_rmii)
 			return -EINVAL;
 		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		if (!bsp_priv->supports_sgmii)
+			return -EINVAL;
+		break;
 	default:
 		dev_err(bsp_priv->dev,
 			"unsupported interface %d", bsp_priv->phy_iface);
@@ -1379,16 +1450,19 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 	if (ret)
 		return ret;
 
+	ret = gmac_clk_enable(bsp_priv, true);
+	if (ret)
+		return ret;
+
+	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_SGMII)
+		goto set_mode;
+
 	ret = rk_get_phy_intf_sel(bsp_priv->phy_iface);
 	if (ret < 0)
-		return ret;
+		goto clk_disable;
 
 	intf = ret;
 
-	ret = gmac_clk_enable(bsp_priv, true);
-	if (ret)
-		return ret;
-
 	if (bsp_priv->gmac_phy_intf_sel_mask ||
 	    bsp_priv->gmac_rmii_mode_mask) {
 		/* If defined, encode the phy_intf_sel value */
@@ -1399,10 +1473,8 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 				      bsp_priv->gmac_rmii_mode_mask);
 
 		ret = rk_write_gmac_grf_reg(bsp_priv, val);
-		if (ret < 0) {
-			gmac_clk_enable(bsp_priv, false);
-			return ret;
-		}
+		if (ret < 0)
+			goto clk_disable;
 	}
 
 	if (bsp_priv->clock.rmii_mode_mask) {
@@ -1410,13 +1482,12 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 				     bsp_priv->clock.rmii_mode_mask);
 
 		ret = rk_write_clock_grf_reg(bsp_priv, val);
-		if (ret < 0) {
-			gmac_clk_enable(bsp_priv, false);
-			return ret;
-		}
+		if (ret < 0)
+			goto clk_disable;
 	}
 
-	/*rmii or rgmii*/
+set_mode:
+	/* rmii, rgmii, sgmii */
 	switch (bsp_priv->phy_iface) {
 	case PHY_INTERFACE_MODE_RGMII:
 		dev_info(dev, "init for RGMII\n");
@@ -1447,15 +1518,20 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 		if (bsp_priv->ops->set_to_rmii)
 			bsp_priv->ops->set_to_rmii(bsp_priv);
 		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		dev_info(dev, "init for SGMII\n");
+		if (bsp_priv->ops->set_to_sgmii)
+			bsp_priv->ops->set_to_sgmii(bsp_priv);
+		break;
 	default:
 		dev_err(dev, "NO interface defined!\n");
+		ret = -EINVAL;
+		goto clk_disable;
 	}
 
 	ret = rk_phy_powerup(bsp_priv);
-	if (ret) {
-		gmac_clk_enable(bsp_priv, false);
-		return ret;
-	}
+	if (ret)
+		goto clk_disable;
 
 	pm_runtime_get_sync(dev);
 
@@ -1463,6 +1539,10 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 		bsp_priv->ops->integrated_phy_powerup(bsp_priv);
 
 	return 0;
+
+clk_disable:
+	gmac_clk_enable(bsp_priv, false);
+	return ret;
 }
 
 static void rk_gmac_powerdown(struct rk_priv_data *gmac)
@@ -1486,6 +1566,9 @@ static void rk_get_interfaces(struct stmmac_priv *priv, void *bsp_priv,
 
 	if (rk->supports_rmii)
 		__set_bit(PHY_INTERFACE_MODE_RMII, interfaces);
+
+	if (rk->supports_sgmii)
+		__set_bit(PHY_INTERFACE_MODE_SGMII, interfaces);
 }
 
 static int rk_set_clk_tx_rate(void *bsp_priv_, struct clk *clk_tx_i,
@@ -1602,6 +1685,17 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	plat_dat->suspend = rk_gmac_suspend;
 	plat_dat->resume = rk_gmac_resume;
 
+	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+		/* SGMII clock always runs at 125 MHz */
+		plat_dat->set_clk_tx_rate = NULL;
+
+		/* SGMII requires a PCS */
+		plat_dat->default_an_inband = true;
+		plat_dat->pcs_init = rk_pcs_init;
+		plat_dat->pcs_exit = rk_pcs_exit;
+		plat_dat->select_pcs = rk_select_pcs;
+	}
+
 	plat_dat->bsp_priv = rk_gmac_setup(pdev, plat_dat, data);
 	if (IS_ERR(plat_dat->bsp_priv))
 		return PTR_ERR(plat_dat->bsp_priv);
-- 
2.47.3