* [PATCH v2 01/18] ARM: dts: qcom: sdx55: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 02/18] arm64: dts: qcom: msm8996: " Krishna Chaitanya Chundru
` (17 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
index d23b8ec08af4..0443a86899a9 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
@@ -249,7 +249,7 @@ &pcie_phy {
&pcie_rc {
perst-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 53 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie_default>;
pinctrl-names = "default";
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 02/18] arm64: dts: qcom: msm8996: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 01/18] ARM: dts: qcom: sdx55: Fix PCIe WAKE# GPIO polarity Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 03/18] arm64: dts: qcom: sdm845: " Krishna Chaitanya Chundru
` (16 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
index d55e4075040f..5b42c266557a 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
@@ -192,7 +192,7 @@ &mmcc {
&pcie0 {
perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&wlan_en>;
vdda-supply = <&pm8994_l28>;
status = "okay";
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
index 77ad613590a3..2abcc733dad8 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
@@ -280,7 +280,7 @@ &pcie0 {
vdda-supply = <&vreg_l28a_0p925>;
perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
};
&pcie_phy {
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 03/18] arm64: dts: qcom: sdm845: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 01/18] ARM: dts: qcom: sdx55: Fix PCIe WAKE# GPIO polarity Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 02/18] arm64: dts: qcom: msm8996: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 04/18] arm64: dts: qcom: sc8180x: " Krishna Chaitanya Chundru
` (15 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 846138149b2c..3e636926231d 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -619,7 +619,7 @@ &mss_pil {
&pcie0 {
status = "okay";
perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 134 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&pcie0_3p3v_dual>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 04/18] arm64: dts: qcom: sc8180x: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (2 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 03/18] arm64: dts: qcom: sdm845: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 05/18] arm64: dts: qcom: sm8150: " Krishna Chaitanya Chundru
` (14 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 2 +-
arch/arm64/boot/dts/qcom/sc8180x-primus.dts | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
index 565e5a9979b1..e6ab523d249e 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
+++ b/arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts
@@ -492,7 +492,7 @@ &mdss_edp_out {
&pcie3 {
perst-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 180 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 180 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie3_default_state>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/sc8180x-primus.dts b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts
index c10a936b320a..327dba55a5ec 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x-primus.dts
+++ b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts
@@ -593,7 +593,7 @@ &mdss_edp_out {
&pcie1 {
perst-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 177 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 177 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie2_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 05/18] arm64: dts: qcom: sm8150: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (3 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 04/18] arm64: dts: qcom: sc8180x: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 06/18] arm64: dts: qcom: sm8250: " Krishna Chaitanya Chundru
` (13 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8150.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 94a3b02cb289..74df5cd86f04 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -1905,7 +1905,7 @@ pcie0: pcie@1c00000 {
phy-names = "pciephy";
perst-gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
- wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 06/18] arm64: dts: qcom: sm8250: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (4 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 05/18] arm64: dts: qcom: sm8150: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 07/18] arm64: dts: qcom: sm8350: " Krishna Chaitanya Chundru
` (12 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8250.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 90f8b091634e..e0c357222bc7 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -2211,7 +2211,7 @@ pcie0: pcie@1c00000 {
phy-names = "pciephy";
perst-gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 81 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_default_state>;
@@ -2338,7 +2338,7 @@ pcie1: pcie@1c08000 {
phy-names = "pciephy";
perst-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 84 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;
@@ -2465,7 +2465,7 @@ pcie2: pcie@1c10000 {
phy-names = "pciephy";
perst-gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 87 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie2_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 07/18] arm64: dts: qcom: sm8350: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (5 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 06/18] arm64: dts: qcom: sm8250: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 08/18] arm64: dts: qcom: sm8450: " Krishna Chaitanya Chundru
` (11 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index bb93c3e9417b..e9b9e03f725e 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -500,7 +500,7 @@ &pcie0 {
pinctrl-0 = <&pcie0_default_state>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -514,7 +514,7 @@ &pcie0_phy {
&pcie1 {
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 08/18] arm64: dts: qcom: sm8450: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (6 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 07/18] arm64: dts: qcom: sm8350: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 09/18] arm64: dts: qcom: sm8550: " Krishna Chaitanya Chundru
` (10 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index b8793482b181..7bc5f85e7ebc 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2021,7 +2021,7 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
phy-names = "pciephy";
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_default_state>;
@@ -2186,7 +2186,7 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
phy-names = "pciephy";
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 09/18] arm64: dts: qcom: sm8550: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (7 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 08/18] arm64: dts: qcom: sm8450: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 10/18] arm64: dts: qcom: sm8650: " Krishna Chaitanya Chundru
` (9 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/qcs8550-aim300.dtsi | 4 ++--
arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts | 4 ++--
arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 4 ++--
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 4 ++--
arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 2 +-
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 2 +-
arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts | 2 +-
7 files changed, 11 insertions(+), 11 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-aim300.dtsi b/arch/arm64/boot/dts/qcom/qcs8550-aim300.dtsi
index ae301d78e071..aaf5eb57ce23 100644
--- a/arch/arm64/boot/dts/qcom/qcs8550-aim300.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs8550-aim300.dtsi
@@ -336,7 +336,7 @@ &mdss_dsi0_phy {
&pcie0 {
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
pinctrl-names = "default";
@@ -349,7 +349,7 @@ &pcie0_phy {
&pcie1 {
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts b/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts
index 9df8dcd6c62b..41b09ab43d0c 100644
--- a/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts
@@ -1045,7 +1045,7 @@ &mdss_dp0 {
&pcie0 {
vddpe-3v3-supply = <&pcie_upd_3p3>;
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
@@ -1146,7 +1146,7 @@ pci@0,1 {
};
&pcie1 {
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
index 82fb10ed6b6b..4777c908c4d7 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
@@ -1087,7 +1087,7 @@ &mdss_dp0 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
@@ -1121,7 +1121,7 @@ &pcie0_phy {
};
&pcie1 {
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index 7c634572c6b7..eb1de33e5ba5 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -739,7 +739,7 @@ &mdss_dp0 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
@@ -756,7 +756,7 @@ &pcie0_phy {
};
&pcie1 {
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index 473ec4e27daf..13cdb5b0ce40 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -987,7 +987,7 @@ &mdss_dp0 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
diff --git a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
index 81c02ee27fe9..cf4e4e9d9e26 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
@@ -510,7 +510,7 @@ &i2c_master_hub_0 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
index 367f6eae5e65..9f347bea6c74 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
@@ -584,7 +584,7 @@ cirrus,gpio-ctrl2 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 10/18] arm64: dts: qcom: sm8650: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (8 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 09/18] arm64: dts: qcom: sm8550: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 11/18] arm64: dts: qcom: sm8750: " Krishna Chaitanya Chundru
` (8 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8650-ayaneo-pocket-s2.dts | 4 ++--
arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 4 ++--
arch/arm64/boot/dts/qcom/sm8650-mtp.dts | 4 ++--
arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 2 +-
4 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8650-ayaneo-pocket-s2.dts b/arch/arm64/boot/dts/qcom/sm8650-ayaneo-pocket-s2.dts
index 6ddf30ecabfe..668c183bc177 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-ayaneo-pocket-s2.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-ayaneo-pocket-s2.dts
@@ -1074,7 +1074,7 @@ &mdss_dp0_out {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
@@ -1108,7 +1108,7 @@ &pcie0_phy {
};
&pcie1 {
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
index 41d0c7edc433..b73ad7861eb4 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
@@ -1027,7 +1027,7 @@ &mdss_dp0 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
@@ -1061,7 +1061,7 @@ &pcie0_phy {
};
&pcie1 {
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
diff --git a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
index 26045430d34a..1332c864801f 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
@@ -642,7 +642,7 @@ &mdss_dsi0_phy {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
@@ -659,7 +659,7 @@ &pcie0_phy {
};
&pcie1 {
- wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
diff --git a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
index 1fb78588a504..2e874f046a0e 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
@@ -1021,7 +1021,7 @@ &mdss_dp0 {
};
&pcie0 {
- wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 11/18] arm64: dts: qcom: sm8750: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (9 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 10/18] arm64: dts: qcom: sm8650: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 12/18] arm64: dts: qcom: kaanapali: " Krishna Chaitanya Chundru
` (7 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
index 9b5fbc004df4..23476fbd993c 100644
--- a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
@@ -1119,7 +1119,7 @@ &pcie0_phy {
};
&pcieport0 {
- wake-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 104 GPIO_ACTIVE_LOW>;
reset-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>;
wifi@0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 12/18] arm64: dts: qcom: kaanapali: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (10 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 11/18] arm64: dts: qcom: sm8750: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 13/18] arm64: dts: qcom: sar2130p: " Krishna Chaitanya Chundru
` (6 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/kaanapali-mtp.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts b/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
index 6d817381bb37..83c4f93a654a 100644
--- a/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
@@ -976,7 +976,7 @@ &pcie0_phy {
};
&pcie_port0 {
- wake-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 104 GPIO_ACTIVE_LOW>;
reset-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>;
wifi@0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 13/18] arm64: dts: qcom: sar2130p: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (11 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 12/18] arm64: dts: qcom: kaanapali: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 14/18] arm64: dts: qcom: monaco: " Krishna Chaitanya Chundru
` (5 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sar2130p-qar2130p.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sar2130p-qar2130p.dts b/arch/arm64/boot/dts/qcom/sar2130p-qar2130p.dts
index 80428c0b3b4e..7469134f42b7 100644
--- a/arch/arm64/boot/dts/qcom/sar2130p-qar2130p.dts
+++ b/arch/arm64/boot/dts/qcom/sar2130p-qar2130p.dts
@@ -358,7 +358,7 @@ &i2c10 {
&pcie0 {
perst-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
pinctrl-names = "default";
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 14/18] arm64: dts: qcom: monaco: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (12 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 13/18] arm64: dts: qcom: sar2130p: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 15/18] arm64: dts: qcom: lemans: " Krishna Chaitanya Chundru
` (4 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/monaco-evk.dts | 4 ++--
arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 4 ++--
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/monaco-evk.dts b/arch/arm64/boot/dts/qcom/monaco-evk.dts
index 9d17ef7d2caf..b30fc7ecdf32 100644
--- a/arch/arm64/boot/dts/qcom/monaco-evk.dts
+++ b/arch/arm64/boot/dts/qcom/monaco-evk.dts
@@ -643,12 +643,12 @@ &pcie1_phy {
&pcieport0 {
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
};
&pcieport1 {
reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
};
&pmm8620au_0_gpios {
diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
index 1ff39530ea3d..2472df47a0ea 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
@@ -615,7 +615,7 @@ &pcie0 {
&pcieport0 {
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
wifi@0 {
compatible = "pci17cb,1103";
@@ -651,7 +651,7 @@ &pcie1 {
&pcieport1 {
reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
};
&pcie1_phy {
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 15/18] arm64: dts: qcom: lemans: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (13 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 14/18] arm64: dts: qcom: monaco: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 16/18] arm64: dts: qcom: talos: " Krishna Chaitanya Chundru
` (3 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/lemans-evk.dts | 4 ++--
arch/arm64/boot/dts/qcom/lemans-ride-common.dtsi | 4 ++--
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
index a45485b54a5b..194e114a12a0 100644
--- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
@@ -840,7 +840,7 @@ &mdss0_dp1_phy {
&pcie0 {
perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_default_state>;
pinctrl-names = "default";
@@ -857,7 +857,7 @@ &pcie0_phy {
&pcie1 {
perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_default_state>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/lemans-ride-common.dtsi b/arch/arm64/boot/dts/qcom/lemans-ride-common.dtsi
index 144f117ba511..3ecf3d464dd7 100644
--- a/arch/arm64/boot/dts/qcom/lemans-ride-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/lemans-ride-common.dtsi
@@ -962,7 +962,7 @@ wake-pins {
&pcie0 {
perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_default_state>;
@@ -972,7 +972,7 @@ &pcie0 {
&pcie1 {
perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 16/18] arm64: dts: qcom: talos: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (14 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 15/18] arm64: dts: qcom: lemans: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 17/18] arm64: dts: qcom: sa8540p-ride: " Krishna Chaitanya Chundru
` (2 subsequent siblings)
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/qcs615-ride.dts | 2 +-
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index 047b4efb04b9..43f110ba3a7c 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -445,7 +445,7 @@ &mdss_dsi0_phy {
&pcie {
perst-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 100 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie_default_state>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
index a31bed7fad07..198f656bddf1 100644
--- a/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
+++ b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
@@ -367,7 +367,7 @@ &mdss_dsi0_phy {
&pcie {
perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 100 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie_default_state>;
pinctrl-names = "default";
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 17/18] arm64: dts: qcom: sa8540p-ride: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (15 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 16/18] arm64: dts: qcom: talos: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 11:54 ` [PATCH v2 18/18] arm64: dts: qcom: kodiak: " Krishna Chaitanya Chundru
2026-09-29 3:14 ` (subset) [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Bjorn Andersson
18 siblings, 0 replies; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index c72faaa0ae7a..e85d78ecac2e 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -374,7 +374,7 @@ &pcie2a {
&pcie2a_port0 {
reset-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
};
&pcie2a_phy {
@@ -397,7 +397,7 @@ &pcie3a {
&pcie3a_port0 {
reset-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
};
&pcie3a_phy {
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v2 18/18] arm64: dts: qcom: kodiak: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (16 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 17/18] arm64: dts: qcom: sa8540p-ride: " Krishna Chaitanya Chundru
@ 2026-09-17 11:54 ` Krishna Chaitanya Chundru
2026-09-17 12:06 ` sashiko-bot
2026-09-29 3:14 ` (subset) [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Bjorn Andersson
18 siblings, 1 reply; 21+ messages in thread
From: Krishna Chaitanya Chundru @ 2026-09-17 11:54 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Krishna Chaitanya Chundru, linux-arm-msm, devicetree,
linux-kernel, konrad.dybcio, mani
The PCIe WAKE# signal is active-low as defined in the PCIe Base
Specification. Fix the wake-gpios polarity by using GPIO_ACTIVE_LOW
instead of GPIO_ACTIVE_HIGH.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts | 3 ++-
arch/arm64/boot/dts/qcom/qcs6490-radxa-dragon-q6a.dts | 4 ++--
arch/arm64/boot/dts/qcom/qcs6490-thundercomm-minipc-g1iot.dts | 4 ++--
arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts | 2 +-
arch/arm64/boot/dts/qcom/qcs6490-vicharak-axon-mini.dts | 4 ++--
5 files changed, 9 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts b/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
index 5bb33a8a9830..509fc4941a02 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
@@ -558,7 +558,7 @@ &pcie0_phy {
&pcie0_port {
reset-gpios = <&tlmm 87 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
};
&pcie1 {
@@ -579,6 +579,7 @@ &pcie1_phy {
&pcie1_port0 {
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
};
&pmk8350_adc_tm {
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-radxa-dragon-q6a.dts b/arch/arm64/boot/dts/qcom/qcs6490-radxa-dragon-q6a.dts
index 41d60c87f5bd..ed0b81710b9a 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-radxa-dragon-q6a.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-radxa-dragon-q6a.dts
@@ -541,7 +541,7 @@ &pcie0_phy {
&pcie0_port {
reset-gpios = <&tlmm 87 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
};
&pcie1 {
@@ -571,7 +571,7 @@ &pcie1_phy {
&pcie1_port0 {
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
};
&pm7325_gpios {
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-minipc-g1iot.dts b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-minipc-g1iot.dts
index 31bafa2cf51d..6527cf815b85 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-minipc-g1iot.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-minipc-g1iot.dts
@@ -705,7 +705,7 @@ &pcie0_phy {
&pcie0_port {
reset-gpios = <&tlmm 87 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
};
&pcie1 {
@@ -736,7 +736,7 @@ &pcie1_phy {
&pcie1_port0 {
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
pcie@0,0 {
compatible = "pci1179,0623";
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
index 13e8e62f6205..4ac2998a0a6a 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-thundercomm-rubikpi3.dts
@@ -833,7 +833,7 @@ &pcie0_phy {
&pcie0_port {
reset-gpios = <&tlmm 87 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
};
&pcie1 {
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-vicharak-axon-mini.dts b/arch/arm64/boot/dts/qcom/qcs6490-vicharak-axon-mini.dts
index 4f2e0109f49b..141d263e6566 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-vicharak-axon-mini.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-vicharak-axon-mini.dts
@@ -653,7 +653,7 @@ &ice {
&pcie0 {
perst-gpios = <&tlmm 87 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_clkreq_n>, <&pcie0_reset_n>, <&pcie0_wake_n>;
pinctrl-names = "default";
@@ -670,7 +670,7 @@ &pcie0_phy {
&pcie1 {
perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ wake-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_reset_n>, <&pcie1_wake_n>, <&pcie1_clkreq_n>;
pinctrl-names = "default";
--
2.34.1
^ permalink raw reply related [flat|nested] 21+ messages in thread* Re: [PATCH v2 18/18] arm64: dts: qcom: kodiak: Fix PCIe WAKE# GPIO polarity
2026-09-17 11:54 ` [PATCH v2 18/18] arm64: dts: qcom: kodiak: " Krishna Chaitanya Chundru
@ 2026-09-17 12:06 ` sashiko-bot
0 siblings, 0 replies; 21+ messages in thread
From: sashiko-bot @ 2026-09-17 12:06 UTC (permalink / raw)
To: Krishna Chaitanya Chundru; +Cc: conor+dt, devicetree, robh
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] dts: undocumented addition of wake-gpios property to pcie1_port0
--
commit 6e97f1471613f8cea666aa46eb12ba3627dc0138
Author: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
arm64: dts: qcom: kodiak: Fix PCIe WAKE# GPIO polarity
This commit updates the polarity of the PCIe WAKE# GPIO across several
Qualcomm device trees to match the active-low requirement defined in the
PCIe Base Specification.
> diff --git a/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts b/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
> index 5bb33a8a98304..509fc4941a029 100644
> --- a/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
> +++ b/arch/arm64/boot/dts/qcom/qcm6490-particle-tachyon.dts
[ ... ]
> @@ -579,6 +579,7 @@ &pcie1_phy {
>
> &pcie1_port0 {
> reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
> };
[Severity: Medium]
The commit message states the intent is to fix the polarity of existing
wake-gpios properties by changing GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW.
However, for &pcie1_port0 in this file, the wake-gpios property did not
exist previously and is being newly added.
Is this an accidental inclusion, or should the commit message be updated
to clarify that wake functionality is also being added for pcie1_port0
on this board?
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260917-root_port-v2-0-0d627d0856d5@oss.qualcomm.com?part=18
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: (subset) [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity
2026-09-17 11:54 [PATCH v2 00/18] arm64: dts: qcom: Fix wake-gpios polarity Krishna Chaitanya Chundru
` (17 preceding siblings ...)
2026-09-17 11:54 ` [PATCH v2 18/18] arm64: dts: qcom: kodiak: " Krishna Chaitanya Chundru
@ 2026-09-29 3:14 ` Bjorn Andersson
18 siblings, 0 replies; 21+ messages in thread
From: Bjorn Andersson @ 2026-09-29 3:14 UTC (permalink / raw)
To: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Krishna Chaitanya Chundru
Cc: linux-arm-msm, devicetree, linux-kernel, konrad.dybcio, mani
On Thu, 17 Sep 2026 17:24:08 +0530, Krishna Chaitanya Chundru wrote:
> PCIe wake is active low signal as per the PCIe base spec, Several Qualcomm
> platform devicetrees incorrectly describe wake-gpios as GPIO_ACTIVE_HIGH.
>
> This series fixes the wake-gpios polarity by using GPIO_ACTIVE_LOW
> instead of GPIO_ACTIVE_HIGH.
>
> Tested on Talos Ride & lemans evk platform.
>
> [...]
Applied, thanks!
[15/18] arm64: dts: qcom: lemans: Fix PCIe WAKE# GPIO polarity
commit: cd8d4803bba672a4d03ce508fc9d2c459eb85c55
[16/18] arm64: dts: qcom: talos: Fix PCIe WAKE# GPIO polarity
commit: e622c5d6553b8a83af04115c87f006406baf2675
[17/18] arm64: dts: qcom: sa8540p-ride: Fix PCIe WAKE# GPIO polarity
commit: 450a0bfdb1b66da50ef98eefe1ff45b7be21e9a7
[18/18] arm64: dts: qcom: kodiak: Fix PCIe WAKE# GPIO polarity
commit: b2b980536b5a4a5420175dfbef7f481408761b7b
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 21+ messages in thread