[PATCH v3 0/5] iio: pressure: dps310: add Zilltek ZTS8032

[PATCH v3 0/5] iio: pressure: dps310: add Zilltek ZTS8032

[Paulius Zaleckas]

The Zilltek ZTS8032 is a register compatible DPS310 with two more
pressure calibration coefficients (c31, c40) and a different TMP_CFG
layout.

1-2: Vendor prefix and the zilltek,zts8032 compatible.
3: Per-chip data in the I2C and ACPI match data, no functional change.
4: OF match table.
5: ZTS8032 chip data: the coefficient count, the TMP_CFG startup value,
   and a Horner step each for c40 and c31.

Based on iio/testing, on top of a22dc7ebb21a ("iio: pressure: dps310:
fix overflow in pressure compensation"). That fix replaces v2's patch 1,
and patch 5 extends its Horner evaluation.

There is no public ZTS8032 datasheet.

Testing: ZTS8032 on an arm64 (MT7987) board, the series and a22dc7ebb21a
backported to 6.12. in_pressure_input matches the datasheet formula
evaluated from the raw and coefficient registers to within 1 Pa at every
oversampling rate from 1 to 128, and TMP_CFG reads 0x00 after probe.
Every patch builds without warnings with W=1 on x86_64 and i386,
dt_binding_check passes. I have no DPS310, so patches 3-4 are untested
on one.

An LLM coding assistant (Claude Code) was used for this series: it
ported the ZTS8032 support from the vendor driver, wrote the code and
changelogs and the hardware test scripts, under my direction. I
reviewed and tested the result.

Changes in v3:
- Drop v2 1/6, superseded by a22dc7ebb21a in iio/testing; rebase onto
  it and add c40 and c31 as Horner steps. This also covers the Sashiko
  overflow report on v2 1/6.
- C99 initializers for the ACPI ID (Andy, Uwe)
- Add DPS310_MAX_COEF_LEN in patch 3 and bump it in patch 5 (Andy)
- Parse c31/c40 based on a chip flag, not the coefficient count (Andy)
- List the supported sensors one per line in Kconfig (Andy)
- Link to v2: https://lore.kernel.org/r/20261013112124.1878296-1-paulius.zaleckas@gmail.com

Changes in v2:
- Split the driver patch into per-chip data, OF match table and
  ZTS8032 support (Andy)
- Drop the linux/mod_devicetable.h include (Andy, Uwe)
- Return -ENODATA when there is no match data (Andy)
- Add Conor's Acked-by to the bindings
- Link to v1: https://lore.kernel.org/r/20261012114550.1680054-1-paulius.zaleckas@ui.com

Paulius Zaleckas (5):
  dt-bindings: vendor-prefixes: Add ZillTek Technology
  dt-bindings: iio: pressure: infineon,dps310: Add Zilltek ZTS8032
  iio: pressure: dps310: add per-chip data
  iio: pressure: dps310: add an OF match table
  iio: pressure: dps310: add Zilltek ZTS8032 support

 .../iio/pressure/infineon,dps310.yaml         |  4 +-
 .../devicetree/bindings/vendor-prefixes.yaml  |  2 +
 drivers/iio/pressure/Kconfig                  |  6 +-
 drivers/iio/pressure/dps310.c                 | 73 ++++++++++++++++---
 4 files changed, 72 insertions(+), 13 deletions(-)


base-commit: a22dc7ebb21a6bd4c8b63bc2c1dd46a24945aae7
-- 
2.55.0

[PATCH v3 1/5] dt-bindings: vendor-prefixes: Add ZillTek Technology

[Paulius Zaleckas]

ZillTek Technology Corp. (Hsinchu, Taiwan) makes MEMS microphones and
barometric pressure sensors such as the ZTS8032.

Link: https://www.zilltek.com/
Assisted-by: LLM
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index ba2002969373..255dc56edc36 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1977,6 +1977,8 @@ patternProperties:
     description: Shenzhen Zidoo Technology Co., Ltd.
   "^zii,.*":
     description: Zodiac Inflight Innovations
+  "^zilltek,.*":
+    description: ZillTek Technology Corp.
   "^zinitix,.*":
     description: Zinitix Co., Ltd
   "^zkmagic,.*":
-- 
2.55.0

[PATCH v3 2/5] dt-bindings: iio: pressure: infineon,dps310: Add Zilltek ZTS8032

[Paulius Zaleckas]

The Zilltek ZTS8032 is register compatible with the DPS310, but has two
more pressure calibration coefficients and takes its temperature from a
different sensor by default, so it cannot use the DPS310 compatible as a
fallback.

Assisted-by: LLM
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 .../devicetree/bindings/iio/pressure/infineon,dps310.yaml     | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
index 1912a1b0b4ba..416117dfd927 100644
--- a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
+++ b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
@@ -11,12 +11,14 @@ maintainers:
 
 description:
   The DPS310 is a barometric pressure and temperature sensor with an I2C
-  interface.
+  interface. The Zilltek ZTS8032 is register compatible with it, but has
+  additional calibration coefficients.
 
 properties:
   compatible:
     enum:
       - infineon,dps310
+      - zilltek,zts8032
 
   reg:
     maxItems: 1
-- 
2.55.0

[PATCH v3 3/5] iio: pressure: dps310: add per-chip data

[Paulius Zaleckas]

Move the coefficient count, the TMP_CFG startup value and the IIO device
name into a per-chip structure, passed through the I2C and ACPI match
data. This prepares for the Zilltek ZTS8032, which has two more
coefficients and a different TMP_CFG layout.

No functional change.

Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 drivers/iio/pressure/dps310.c | 35 +++++++++++++++++++++++++++--------
 1 file changed, 27 insertions(+), 8 deletions(-)

diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
index 1d0b3232db9e..aa80d106ac44 100644
--- a/drivers/iio/pressure/dps310.c
+++ b/drivers/iio/pressure/dps310.c
@@ -62,6 +62,8 @@
 #define DPS310_RESET		0x0c
 #define  DPS310_RESET_MAGIC	0x09
 #define DPS310_COEF_BASE	0x10
+#define DPS310_COEF_LEN		18
+#define DPS310_MAX_COEF_LEN	18
 
 /* Make sure sleep time is <= 30ms for usleep_range */
 #define DPS310_POLL_SLEEP_US(t)		min(30000, (t) / 8)
@@ -86,10 +88,23 @@ static const int scale_factors[] = {
 	2088960,
 };
 
+struct dps310_chip_info {
+	const char *name;
+	u8 tmp_cfg;	/* TMP_CFG at startup: sensor the coefficients are for */
+	u8 coef_len;
+};
+
+static const struct dps310_chip_info dps310_chip_info = {
+	.name = "dps310",
+	.tmp_cfg = DPS310_TMP_EXT,
+	.coef_len = DPS310_COEF_LEN,
+};
+
 struct dps310_data {
 	struct i2c_client *client;
 	struct regmap *regmap;
 	struct mutex lock;	/* Lock for sequential HW access functions */
+	const struct dps310_chip_info *info;
 
 	s32 c0, c1;
 	s32 c00, c10, c20, c30, c01, c11, c21;
@@ -149,13 +164,13 @@ static const struct iio_chan_spec dps310_channels[] = {
 static int dps310_get_coefs(struct dps310_data *data)
 {
 	int rc;
-	u8 coef[18];
+	u8 coef[DPS310_MAX_COEF_LEN];
 	u32 c0, c1;
 	u32 c00, c10, c20, c30, c01, c11, c21;
 
 	/* Read all sensor calibration coefficients from the COEF registers. */
 	rc = regmap_bulk_read(data->regmap, DPS310_COEF_BASE, coef,
-			      sizeof(coef));
+			      data->info->coef_len);
 	if (rc < 0)
 		return rc;
 
@@ -252,10 +267,10 @@ static int dps310_startup(struct dps310_data *data)
 		return rc;
 
 	/*
-	 * Set up external (MEMS) temperature sensor in single sample, one
-	 * measurement per second mode
+	 * Set up the temperature sensor the coefficients are for in single
+	 * sample, one measurement per second mode
 	 */
-	rc = regmap_write(data->regmap, DPS310_TMP_CFG, DPS310_TMP_EXT);
+	rc = regmap_write(data->regmap, DPS310_TMP_CFG, data->info->tmp_cfg);
 	if (rc)
 		return rc;
 
@@ -979,7 +994,11 @@ static int dps310_probe(struct i2c_client *client)
 	data->client = client;
 	mutex_init(&data->lock);
 
-	iio->name = DPS310_DEV_NAME;
+	data->info = i2c_get_match_data(client);
+	if (!data->info)
+		return -ENODATA;
+
+	iio->name = data->info->name;
 	iio->channels = dps310_channels;
 	iio->num_channels = ARRAY_SIZE(dps310_channels);
 	iio->info = &dps310_info;
@@ -1018,13 +1037,13 @@ static int dps310_probe(struct i2c_client *client)
 }
 
 static const struct i2c_device_id dps310_id[] = {
-	{ .name = DPS310_DEV_NAME },
+	{ .name = "dps310", .driver_data = (kernel_ulong_t)&dps310_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, dps310_id);
 
 static const struct acpi_device_id dps310_acpi_match[] = {
-	{ "IFX3100" },
+	{ .id = "IFX3100", .driver_data = (kernel_ulong_t)&dps310_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, dps310_acpi_match);
-- 
2.55.0

Re: [PATCH v3 3/5] iio: pressure: dps310: add per-chip data

[Joshua Crofts]

On Thu, 15 Oct 2026 13:49:43 +0300
Paulius Zaleckas <paulius.zaleckas@gmail.com> wrote:

> Move the coefficient count, the TMP_CFG startup value and the IIO device
> name into a per-chip structure, passed through the I2C and ACPI match
> data. This prepares for the Zilltek ZTS8032, which has two more
> coefficients and a different TMP_CFG layout.
> 
> No functional change.
> 
> Assisted-by: LLM
> Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
> ---

LGTM.

Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>

-- 
Kind regards,
Joshua Crofts

[PATCH v3 4/5] iio: pressure: dps310: add an OF match table

[Paulius Zaleckas]

Devicetree nodes match the driver only through the I2C ID table fallback.
Add an OF match table, so the chip data comes from the compatible and the
module autoloads from the of: modalias the I2C core reports for
devicetree devices.

Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 drivers/iio/pressure/dps310.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
index aa80d106ac44..ad3860d11592 100644
--- a/drivers/iio/pressure/dps310.c
+++ b/drivers/iio/pressure/dps310.c
@@ -1042,6 +1042,12 @@ static const struct i2c_device_id dps310_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, dps310_id);
 
+static const struct of_device_id dps310_of_match[] = {
+	{ .compatible = "infineon,dps310", .data = &dps310_chip_info },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, dps310_of_match);
+
 static const struct acpi_device_id dps310_acpi_match[] = {
 	{ .id = "IFX3100", .driver_data = (kernel_ulong_t)&dps310_chip_info },
 	{ }
@@ -1051,6 +1057,7 @@ MODULE_DEVICE_TABLE(acpi, dps310_acpi_match);
 static struct i2c_driver dps310_driver = {
 	.driver = {
 		.name = DPS310_DEV_NAME,
+		.of_match_table = dps310_of_match,
 		.acpi_match_table = dps310_acpi_match,
 	},
 	.probe = dps310_probe,
-- 
2.55.0

Re: [PATCH v3 4/5] iio: pressure: dps310: add an OF match table

[Joshua Crofts]

On Thu, 15 Oct 2026 13:49:44 +0300
Paulius Zaleckas <paulius.zaleckas@gmail.com> wrote:

> Devicetree nodes match the driver only through the I2C ID table fallback.
> Add an OF match table, so the chip data comes from the compatible and the
> module autoloads from the of: modalias the I2C core reports for
> devicetree devices.
> 
> Assisted-by: LLM
> Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
> ---

Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>

-- 
Kind regards,
Joshua Crofts

[PATCH v3 5/5] iio: pressure: dps310: add Zilltek ZTS8032 support

[Paulius Zaleckas]

The Zilltek ZTS8032 has the DPS310 register map, scale factors and
compensation, with these differences:

- two more pressure coefficients, c31 and c40 at 0x22-0x25, adding
  c40 * Praw_sc^4 + c31 * Traw_sc * Praw_sc^3 to the polynomial
- TMP_EXT is MEAS_CFG bit 3, and the temperature coefficients are for
  the internal sensor (COEF_SRCE reads 0x06). TMP_CFG bit 7 is the top
  bit of a 4-bit TMP_RATE, so the DPS310 TMP_EXT write would select a
  25/16 Hz background rate instead of the external sensor.
- product ID 0x11 instead of 0x10, the driver does not check it

Add its chip data, reading 22 coefficient bytes and leaving TMP_CFG at
0, a Horner step for each of c40 and c31, and the I2C and OF IDs.

Tested on a ZTS8032 over I2C: in_pressure_input is within 1 Pa of the
datasheet formula evaluated from the raw and coefficient registers at
every oversampling rate from 1 to 128, and TMP_CFG reads 0x00 after
probe.

Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 drivers/iio/pressure/Kconfig  |  6 ++++--
 drivers/iio/pressure/dps310.c | 33 ++++++++++++++++++++++++++++++---
 2 files changed, 34 insertions(+), 5 deletions(-)

diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
index cef8b90b9ae7..21363d542c38 100644
--- a/drivers/iio/pressure/Kconfig
+++ b/drivers/iio/pressure/Kconfig
@@ -115,8 +115,10 @@ config DPS310
 	select IIO_BUFFER
 	select IIO_TRIGGERED_BUFFER
 	help
-	  Support for the Infineon DPS310 digital barometric pressure sensor.
-	  It can be accessed over I2C bus.
+	  Support for the following digital barometric pressure sensors:
+	  - Infineon DPS310
+	  - Zilltek ZTS8032
+	  They can be accessed over I2C bus.
 
 	  This driver can also be built as a module.  If so, the module will be
 	  called dps310.
diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
index ad3860d11592..940bde38e8e3 100644
--- a/drivers/iio/pressure/dps310.c
+++ b/drivers/iio/pressure/dps310.c
@@ -7,6 +7,10 @@
  *
  * https://www.infineon.com/dgdl/?fileId=5546d462576f34750157750826c42242
  *
+ * The Zilltek ZTS8032 is register compatible, with two more pressure
+ * calibration coefficients (c31, c40) and temperature calibrated against
+ * the internal sensor.
+ *
  * Temperature calculation:
  *   c0 * 0.5 + c1 * T_raw / kT °C
  *
@@ -63,7 +67,8 @@
 #define  DPS310_RESET_MAGIC	0x09
 #define DPS310_COEF_BASE	0x10
 #define DPS310_COEF_LEN		18
-#define DPS310_MAX_COEF_LEN	18
+#define ZTS8032_COEF_LEN	22
+#define DPS310_MAX_COEF_LEN	22
 
 /* Make sure sleep time is <= 30ms for usleep_range */
 #define DPS310_POLL_SLEEP_US(t)		min(30000, (t) / 8)
@@ -92,6 +97,7 @@ struct dps310_chip_info {
 	const char *name;
 	u8 tmp_cfg;	/* TMP_CFG at startup: sensor the coefficients are for */
 	u8 coef_len;
+	bool has_c31_c40;
 };
 
 static const struct dps310_chip_info dps310_chip_info = {
@@ -100,6 +106,14 @@ static const struct dps310_chip_info dps310_chip_info = {
 	.coef_len = DPS310_COEF_LEN,
 };
 
+/* TMP_CFG bit 7 is a rate bit here; the internal sensor is the default */
+static const struct dps310_chip_info zts8032_chip_info = {
+	.name = "zts8032",
+	.tmp_cfg = 0,
+	.coef_len = ZTS8032_COEF_LEN,
+	.has_c31_c40 = true,
+};
+
 struct dps310_data {
 	struct i2c_client *client;
 	struct regmap *regmap;
@@ -108,6 +122,7 @@ struct dps310_data {
 
 	s32 c0, c1;
 	s32 c00, c10, c20, c30, c01, c11, c21;
+	s32 c31, c40;
 	s32 pressure_raw;
 	s32 temp_raw;
 	bool timeout_recovery_failed;
@@ -210,6 +225,11 @@ static int dps310_get_coefs(struct dps310_data *data)
 	c30 = (coef[16] << 8) | coef[17];
 	data->c30 = sign_extend32(c30, 15);
 
+	if (data->info->has_c31_c40) {
+		data->c31 = sign_extend32((coef[18] << 8) | coef[19], 15);
+		data->c40 = sign_extend32((coef[20] << 8) | coef[21], 15);
+	}
+
 	return 0;
 }
 
@@ -711,10 +731,15 @@ static int dps310_calculate_pressure(struct dps310_data *data, int *val)
 	if (rc)
 		return rc;
 
-	/* Section 4.9.1 of the DPS310 spec, Horner form to avoid overflow */
-	if (!dps310_horner_step(&prs, data->c30, p, kp) ||
+	/*
+	 * Section 4.9.1 of the DPS310 spec, Horner form to avoid overflow.
+	 * c40 and c31 are ZTS8032 only and zero on the DPS310.
+	 */
+	if (!dps310_horner_step(&prs, data->c40, p, kp) ||
+	    !dps310_horner_step(&prs, data->c30, p, kp) ||
 	    !dps310_horner_step(&prs, data->c20, p, kp) ||
 	    !dps310_horner_step(&prs, data->c10, p, kp) ||
+	    !dps310_horner_step(&tmp, data->c31, p, kp) ||
 	    !dps310_horner_step(&tmp, data->c21, p, kp) ||
 	    !dps310_horner_step(&tmp, data->c11, p, kp) ||
 	    !dps310_horner_step(&tmp, data->c01, t, kt))
@@ -1038,12 +1063,14 @@ static int dps310_probe(struct i2c_client *client)
 
 static const struct i2c_device_id dps310_id[] = {
 	{ .name = "dps310", .driver_data = (kernel_ulong_t)&dps310_chip_info },
+	{ .name = "zts8032", .driver_data = (kernel_ulong_t)&zts8032_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, dps310_id);
 
 static const struct of_device_id dps310_of_match[] = {
 	{ .compatible = "infineon,dps310", .data = &dps310_chip_info },
+	{ .compatible = "zilltek,zts8032", .data = &zts8032_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, dps310_of_match);
-- 
2.55.0

Re: [PATCH v3 5/5] iio: pressure: dps310: add Zilltek ZTS8032 support

[Andy Shevchenko]

On Thu, Oct 15, 2026 at 01:49:45PM +0300, Paulius Zaleckas wrote:
> The Zilltek ZTS8032 has the DPS310 register map, scale factors and
> compensation, with these differences:
> 
> - two more pressure coefficients, c31 and c40 at 0x22-0x25, adding
>   c40 * Praw_sc^4 + c31 * Traw_sc * Praw_sc^3 to the polynomial
> - TMP_EXT is MEAS_CFG bit 3, and the temperature coefficients are for
>   the internal sensor (COEF_SRCE reads 0x06). TMP_CFG bit 7 is the top
>   bit of a 4-bit TMP_RATE, so the DPS310 TMP_EXT write would select a
>   25/16 Hz background rate instead of the external sensor.
> - product ID 0x11 instead of 0x10, the driver does not check it
> 
> Add its chip data, reading 22 coefficient bytes and leaving TMP_CFG at
> 0, a Horner step for each of c40 and c31, and the I2C and OF IDs.
> 
> Tested on a ZTS8032 over I2C: in_pressure_input is within 1 Pa of the
> datasheet formula evaluated from the raw and coefficient registers at
> every oversampling rate from 1 to 128, and TMP_CFG reads 0x00 after
> probe.

...

>  #define DPS310_COEF_LEN		18
> -#define DPS310_MAX_COEF_LEN	18
> +#define ZTS8032_COEF_LEN	22
> +#define DPS310_MAX_COEF_LEN	22

I probably was unclear. What I meant is the agnostic name for that.

After the first patch:

#define DPS310_COEF_LEN		18

#define MAX_COEF_LEN		18

After this one

#define DPS310_COEF_LEN		18
#define ZTS8032_COEF_LEN	22

#define MAX_COEF_LEN		22

...

Everything else looks good to me.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v3 0/5] iio: pressure: dps310: add Zilltek ZTS8032

[Andy Shevchenko]

On Thu, Oct 15, 2026 at 01:49:40PM +0300, Paulius Zaleckas wrote:
> The Zilltek ZTS8032 is a register compatible DPS310 with two more
> pressure calibration coefficients (c31, c40) and a different TMP_CFG
> layout.
> 
> 1-2: Vendor prefix and the zilltek,zts8032 compatible.
> 3: Per-chip data in the I2C and ACPI match data, no functional change.
> 4: OF match table.
> 5: ZTS8032 chip data: the coefficient count, the TMP_CFG startup value,
>    and a Horner step each for c40 and c31.
> 
> Based on iio/testing, on top of a22dc7ebb21a ("iio: pressure: dps310:
> fix overflow in pressure compensation"). That fix replaces v2's patch 1,
> and patch 5 extends its Horner evaluation.
> 
> There is no public ZTS8032 datasheet.
> 
> Testing: ZTS8032 on an arm64 (MT7987) board, the series and a22dc7ebb21a
> backported to 6.12. in_pressure_input matches the datasheet formula
> evaluated from the raw and coefficient registers to within 1 Pa at every
> oversampling rate from 1 to 128, and TMP_CFG reads 0x00 after probe.
> Every patch builds without warnings with W=1 on x86_64 and i386,
> dt_binding_check passes. I have no DPS310, so patches 3-4 are untested
> on one.
> 
> An LLM coding assistant (Claude Code) was used for this series: it
> ported the ZTS8032 support from the vendor driver, wrote the code and
> changelogs and the hardware test scripts, under my direction. I
> reviewed and tested the result.

I have a single nit-pick (but two patches might be updated), otherwise
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
for the whole series.

-- 
With Best Regards,
Andy Shevchenko