[PATCH v5 6/8] phy: rockchip-samsung-dcphy: Add MIPI D-PHY receiver support

[Jason Yang <jason98166@gmail.com>]

Add the receiver half of the block, so a MIPI CSI-2 camera can use the
same PHY that already drives a MIPI DSI output on RK3588. It follows the
receiver start-up sequence in the RK3588 TRM [1]. The HS-RX settle values
come from the RK3588 vendor kernel.

The initial deskew calibration that the D-PHY specification asks for
above 1.5 Gbps is not implemented; the vendor kernel programs it from
RK3576 onwards only.

Tested on RK3588 with an IMX219 on the receiver and a DSI panel on the
transmitter of the same PHY.

[1] RK3588 TRM: sections 22.6.3 (receiver start-up) and 22.6.4.3
    (worked receiver example)

Assisted-by: LLM
Signed-off-by: Jason Yang <jason98166@gmail.com>
---
 drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c | 390 +++++++++++++++++++++-
 1 file changed, 387 insertions(+), 3 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c b/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
index 316d4c4d49c1..54a7af610282 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
@@ -244,6 +244,63 @@
 #define T_TA_GET(x)		FIELD_PREP(GENMASK(7, 4), x)
 #define T_TA_GO(x)		FIELD_PREP(GENMASK(3, 0), x)
 
+/* D-PHY receiver registers (clock lane + four data lanes) */
+#define DPHY_SC_GNR_CON0	0x0b00
+#define DPHY_SC_GNR_CON1	0x0b04
+#define DPHY_SC_ANA_CON1	0x0b0c
+#define HS_RX_BIAS_CON(x)	FIELD_PREP(GENMASK(15, 11), x)
+#define DPHY_SC_ANA_CON2	0x0b10
+#define HS_TERM_SW(x)		FIELD_PREP(GENMASK(2, 0), x)
+#define DPHY_SC_ANA_CON3	0x0b14
+#define ULPS_HYS_SW_DPHY(x)	FIELD_PREP(GENMASK(10, 8), x)
+#define DPHY_SC_TIME_CON0	0x0b30
+#define T_CLK_SETTLE(x)		FIELD_PREP(GENMASK(7, 0), x)
+#define T_CLK_MISS(x)		FIELD_PREP(GENMASK(11, 8), x)
+#define COMBO_SD0_GNR_CON0	0x0c00
+#define COMBO_SD0_GNR_CON1	0x0c04
+#define COMBO_SD0_ANA_CON1	0x0c0c
+#define COMBO_SD0_ANA_CON2	0x0c10
+#define SKEW_DLYSEL(x)		FIELD_PREP(GENMASK(9, 8), x)
+#define RX_TERM_SW(x)		FIELD_PREP(GENMASK(2, 0), x)
+#define COMBO_SD0_ANA_CON3	0x0c14
+#define SEL_ESCPOL		BIT(11)
+#define LP_HYS_SW(x)		FIELD_PREP(GENMASK(5, 4), x)
+#define COMBO_SD0_ANA_CON7	0x0c24
+#define CLK_DBL_CTRL(x)		FIELD_PREP(GENMASK(7, 6), x)
+#define COMBO_SD0_TIME_CON0	0x0c30
+#define T_HS_SETTLE(x)		FIELD_PREP(GENMASK(7, 0), x)
+#define SETTLE_CLK_SEL		BIT(8)
+#define COMBO_SD0_TIME_CON1	0x0c34
+#define T_ERR_SOT_SYNC(x)	FIELD_PREP(GENMASK(7, 0), x)
+#define COMBO_SD0_DESKEW_CON2	0x0c48
+#define SKEW_CAL_CLK_COARSE_SET(x) FIELD_PREP(GENMASK(4, 0), x)
+#define COMBO_SD1_GNR_CON0	0x0d00
+#define COMBO_SD1_GNR_CON1	0x0d04
+#define COMBO_SD1_ANA_CON1	0x0d0c
+#define COMBO_SD1_ANA_CON2	0x0d10
+#define COMBO_SD1_ANA_CON3	0x0d14
+#define COMBO_SD1_ANA_CON7	0x0d24
+#define COMBO_SD1_TIME_CON0	0x0d30
+#define COMBO_SD1_TIME_CON1	0x0d34
+#define COMBO_SD1_DESKEW_CON2	0x0d48
+#define COMBO_SD2_GNR_CON0	0x0e00
+#define COMBO_SD2_GNR_CON1	0x0e04
+#define COMBO_SD2_ANA_CON1	0x0e0c
+#define COMBO_SD2_ANA_CON2	0x0e10
+#define COMBO_SD2_ANA_CON3	0x0e14
+#define COMBO_SD2_ANA_CON7	0x0e24
+#define COMBO_SD2_TIME_CON0	0x0e30
+#define COMBO_SD2_TIME_CON1	0x0e34
+#define COMBO_SD2_DESKEW_CON2	0x0e48
+#define DPHY_SD3_GNR_CON0	0x0f00
+#define DPHY_SD3_GNR_CON1	0x0f04
+#define DPHY_SD3_ANA_CON1	0x0f0c
+#define DPHY_SD3_ANA_CON2	0x0f10
+#define DPHY_SD3_ANA_CON3	0x0f14
+#define DPHY_SD3_TIME_CON0	0x0f30
+#define DPHY_SD3_TIME_CON1	0x0f34
+#define DPHY_SD3_DESKEW_CON2	0x0f48
+
 /* MIPI_CDPHY_GRF registers */
 #define MIPI_DCPHY_GRF_CON0		0x0000
 #define S_CPHY_MODE			FIELD_PREP_WM16(BIT(3), 1)
@@ -283,6 +340,7 @@ struct samsung_mipi_dcphy_plat_data {
 struct samsung_mipi_phy {
 	struct phy *phy;
 	unsigned int lanes;
+	unsigned long long hs_clk_rate;
 };
 
 struct samsung_mipi_dcphy {
@@ -979,6 +1037,260 @@ struct samsung_mipi_dphy_timing samsung_mipi_dphy_timing_table[] = {
 	{  80,  2,   0,  0, 28,  5,  0, 22,  2,  0,  5},
 };
 
+/* D-PHY receiver HS-RX configuration lookup */
+struct samsung_mipi_dphy_rx_hsfreq_range {
+	u32 range_h_mbps;
+	u16 cfg_bit;
+};
+
+/*
+ * HS RX settle values taken verbatim from the rk3588 vendor kernel.
+ * The TRM defines these fields but defers the per-data-rate table to a
+ * timing supplement. Each cfg_bit is a pre-combined SETTLE_CLK_SEL |
+ * T_HS_SETTLE value for the data-lane TIME_CON0: bit 8 selects the
+ * divide-by-2 settle clock below 1500 Mbps per the TRM (the vendor
+ * table switches one bucket early, at 1490 Mbps, and is kept
+ * unchanged). The TRM marks bit 8 read-only, but the vendor kernel has
+ * always programmed it. Sorted by .range_h_mbps ascending.
+ */
+static const struct samsung_mipi_dphy_rx_hsfreq_range samsung_mipi_dphy_rx_hsfreq_ranges[] = {
+	{   80, 0x105 }, {  100, 0x106 }, {  120, 0x107 }, {  140, 0x108 },
+	{  160, 0x109 }, {  180, 0x10a }, {  200, 0x10b }, {  220, 0x10c },
+	{  240, 0x10d }, {  270, 0x10e }, {  290, 0x10f }, {  310, 0x110 },
+	{  330, 0x111 }, {  350, 0x112 }, {  370, 0x113 }, {  390, 0x114 },
+	{  410, 0x115 }, {  430, 0x116 }, {  450, 0x117 }, {  470, 0x118 },
+	{  490, 0x119 }, {  510, 0x11a }, {  540, 0x11b }, {  560, 0x11c },
+	{  580, 0x11d }, {  600, 0x11e }, {  620, 0x11f }, {  640, 0x120 },
+	{  660, 0x121 }, {  680, 0x122 }, {  700, 0x123 }, {  720, 0x124 },
+	{  740, 0x125 }, {  760, 0x126 }, {  790, 0x127 }, {  810, 0x128 },
+	{  830, 0x129 }, {  850, 0x12a }, {  870, 0x12b }, {  890, 0x12c },
+	{  910, 0x12d }, {  930, 0x12e }, {  950, 0x12f }, {  970, 0x130 },
+	{  990, 0x131 }, { 1010, 0x132 }, { 1030, 0x133 }, { 1060, 0x134 },
+	{ 1080, 0x135 }, { 1100, 0x136 }, { 1120, 0x137 }, { 1140, 0x138 },
+	{ 1160, 0x139 }, { 1180, 0x13a }, { 1200, 0x13b }, { 1220, 0x13c },
+	{ 1240, 0x13d }, { 1260, 0x13e }, { 1280, 0x13f }, { 1310, 0x140 },
+	{ 1330, 0x141 }, { 1350, 0x142 }, { 1370, 0x143 }, { 1390, 0x144 },
+	{ 1410, 0x145 }, { 1430, 0x146 }, { 1450, 0x147 }, { 1470, 0x148 },
+	{ 1490, 0x149 }, { 1580, 0x007 }, { 1740, 0x008 }, { 1910, 0x009 },
+	{ 2070, 0x00a }, { 2240, 0x00b }, { 2410, 0x00c }, { 2570, 0x00d },
+	{ 2740, 0x00e }, { 2910, 0x00f }, { 3070, 0x010 }, { 3240, 0x011 },
+	{ 3410, 0x012 }, { 3570, 0x013 }, { 3740, 0x014 }, { 3890, 0x015 },
+	{ 4070, 0x016 }, { 4240, 0x017 }, { 4400, 0x018 }, { 4500, 0x019 },
+};
+
+static int samsung_mipi_dphy_rx_lookup_hsfreq(u32 lane_mbps, u16 *cfg_bit)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(samsung_mipi_dphy_rx_hsfreq_ranges); i++) {
+		if (lane_mbps <= samsung_mipi_dphy_rx_hsfreq_ranges[i].range_h_mbps) {
+			*cfg_bit = samsung_mipi_dphy_rx_hsfreq_ranges[i].cfg_bit;
+			return 0;
+		}
+	}
+
+	return -ERANGE;
+}
+
+/* SKEW_DLYSEL per data rate, from the RK3588 TRM ANA_CON2 description */
+static u32 samsung_mipi_dphy_rx_data_lane_dlysel(u32 lane_mbps)
+{
+	if (lane_mbps < 1500)
+		return 0;
+	if (lane_mbps < 2000)
+		return SKEW_DLYSEL(3);
+	if (lane_mbps < 3000)
+		return SKEW_DLYSEL(2);
+	if (lane_mbps < 4000)
+		return SKEW_DLYSEL(1);
+	return 0;
+}
+
+/*
+ * Per-data-lane register bases, indexed by lane number. The clock lane
+ * shares the same block spacing but is programmed separately: its
+ * TIME_CON0 holds T_CLK_SETTLE/T_CLK_MISS rather than the per-rate
+ * T_HS_SETTLE/SETTLE_CLK_SEL, and it has no deskew configuration.
+ */
+static const u32 rx_data_lane_gnr_con0[] = {
+	COMBO_SD0_GNR_CON0, COMBO_SD1_GNR_CON0,
+	COMBO_SD2_GNR_CON0, DPHY_SD3_GNR_CON0,
+};
+
+static const u32 rx_data_lane_gnr_con1[] = {
+	COMBO_SD0_GNR_CON1, COMBO_SD1_GNR_CON1,
+	COMBO_SD2_GNR_CON1, DPHY_SD3_GNR_CON1,
+};
+
+static const u32 rx_lane_time_con0[] = {
+	COMBO_SD0_TIME_CON0, COMBO_SD1_TIME_CON0,
+	COMBO_SD2_TIME_CON0, DPHY_SD3_TIME_CON0,
+};
+
+static const u32 rx_lane_time_con1[] = {
+	COMBO_SD0_TIME_CON1, COMBO_SD1_TIME_CON1,
+	COMBO_SD2_TIME_CON1, DPHY_SD3_TIME_CON1,
+};
+
+/*
+ * These RX analog tuning values come from the vendor kernel. The
+ * termination (RX_TERM_SW/HS_TERM_SW = 2) is the 96.6 ohm setting the
+ * TRM ANA_CON2 value list annotates as the default, although the
+ * register itself resets to 102 ohm. Data lane 0 differs on purpose:
+ * the vendor's default receive profile applies the LP hysteresis and
+ * the swapped escape clock polarity to lane 0 only, and no manual
+ * skew-calibration delay there against three 30 ps steps on the other
+ * lanes. Data lane 3 is a plain D-PHY lane with no ANA_CON7, so it
+ * gets no CLK_DBL_CTRL write.
+ */
+static void samsung_mipi_dphy_rx_config_common(struct samsung_mipi_dcphy *samsung)
+{
+	struct samsung_mipi_phy *rx = &samsung->rx;
+	u32 dlysel = samsung_mipi_dphy_rx_data_lane_dlysel(div_u64(rx->hs_clk_rate,
+								   1000000));
+	u32 ana_con2_common = dlysel | RX_TERM_SW(2);
+
+	/* Clock lane */
+	regmap_write(samsung->regmap, DPHY_SC_ANA_CON1, HS_RX_BIAS_CON(0x10));
+	regmap_write(samsung->regmap, DPHY_SC_ANA_CON2, HS_TERM_SW(2));
+	regmap_write(samsung->regmap, DPHY_SC_ANA_CON3, ULPS_HYS_SW_DPHY(6));
+
+	/* Data lane 0; a zero lane count is rejected at power-on */
+	regmap_write(samsung->regmap, COMBO_SD0_ANA_CON1, HS_RX_BIAS_CON(0x10));
+	regmap_write(samsung->regmap, COMBO_SD0_ANA_CON2, ana_con2_common);
+	regmap_write(samsung->regmap, COMBO_SD0_ANA_CON3,
+		     ULPS_HYS_SW_DPHY(6) | LP_HYS_SW(3) | SEL_ESCPOL);
+	regmap_write(samsung->regmap, COMBO_SD0_ANA_CON7, CLK_DBL_CTRL(1));
+	regmap_write(samsung->regmap, COMBO_SD0_DESKEW_CON2,
+		     SKEW_CAL_CLK_COARSE_SET(0));
+
+	/* Data lane 1 */
+	if (rx->lanes > 1) {
+		regmap_write(samsung->regmap, COMBO_SD1_ANA_CON1,
+			     HS_RX_BIAS_CON(0x10));
+		regmap_write(samsung->regmap, COMBO_SD1_ANA_CON2,
+			     ana_con2_common);
+		regmap_write(samsung->regmap, COMBO_SD1_ANA_CON3,
+			     ULPS_HYS_SW_DPHY(6));
+		regmap_write(samsung->regmap, COMBO_SD1_ANA_CON7,
+			     CLK_DBL_CTRL(1));
+		regmap_write(samsung->regmap, COMBO_SD1_DESKEW_CON2,
+			     SKEW_CAL_CLK_COARSE_SET(3));
+	}
+
+	/* Data lane 2 */
+	if (rx->lanes > 2) {
+		regmap_write(samsung->regmap, COMBO_SD2_ANA_CON1,
+			     HS_RX_BIAS_CON(0x10));
+		regmap_write(samsung->regmap, COMBO_SD2_ANA_CON2,
+			     ana_con2_common);
+		regmap_write(samsung->regmap, COMBO_SD2_ANA_CON3,
+			     ULPS_HYS_SW_DPHY(6));
+		regmap_write(samsung->regmap, COMBO_SD2_ANA_CON7,
+			     CLK_DBL_CTRL(1));
+		regmap_write(samsung->regmap, COMBO_SD2_DESKEW_CON2,
+			     SKEW_CAL_CLK_COARSE_SET(3));
+	}
+
+	/* Data lane 3 */
+	if (rx->lanes > 3) {
+		regmap_write(samsung->regmap, DPHY_SD3_ANA_CON1,
+			     HS_RX_BIAS_CON(0x10));
+		regmap_write(samsung->regmap, DPHY_SD3_ANA_CON2,
+			     ana_con2_common);
+		regmap_write(samsung->regmap, DPHY_SD3_ANA_CON3,
+			     ULPS_HYS_SW_DPHY(6));
+		regmap_write(samsung->regmap, DPHY_SD3_DESKEW_CON2,
+			     SKEW_CAL_CLK_COARSE_SET(3));
+	}
+}
+
+static int samsung_mipi_dphy_rx_config_settle(struct samsung_mipi_dcphy *samsung)
+{
+	struct samsung_mipi_phy *rx = &samsung->rx;
+	u32 lane_mbps = div_u64(rx->hs_clk_rate, 1000000);
+	unsigned int i;
+	u16 cfg_bit;
+	int ret;
+
+	ret = samsung_mipi_dphy_rx_lookup_hsfreq(lane_mbps, &cfg_bit);
+	if (ret) {
+		dev_err(samsung->dev, "no RX hsfreq cfg for %u Mbps\n",
+			lane_mbps);
+		return ret;
+	}
+
+	/*
+	 * Clock-lane settle uses the fixed value from the TRM RX bring-up
+	 * example, unlike the per-rate data-lane settle below.
+	 */
+	regmap_write(samsung->regmap, DPHY_SC_TIME_CON0,
+		     T_CLK_SETTLE(0x01) | T_CLK_MISS(0x03));
+
+	for (i = 0; i < rx->lanes; i++) {
+		regmap_update_bits(samsung->regmap, rx_lane_time_con0[i],
+				   T_HS_SETTLE(0xff) | SETTLE_CLK_SEL, cfg_bit);
+		regmap_update_bits(samsung->regmap, rx_lane_time_con1[i],
+				   T_ERR_SOT_SYNC(0xff), T_ERR_SOT_SYNC(0x03));
+	}
+
+	return 0;
+}
+
+static void samsung_mipi_dphy_rx_lane_disable(struct samsung_mipi_dcphy *samsung)
+{
+	struct samsung_mipi_phy *rx = &samsung->rx;
+	unsigned int i;
+
+	regmap_update_bits(samsung->regmap, DPHY_SC_GNR_CON0, PHY_ENABLE, 0);
+	for (i = 0; i < rx->lanes; i++)
+		regmap_update_bits(samsung->regmap, rx_data_lane_gnr_con0[i],
+				   PHY_ENABLE, 0);
+}
+
+static int samsung_mipi_dphy_rx_lane_enable(struct samsung_mipi_dcphy *samsung)
+{
+	struct samsung_mipi_phy *rx = &samsung->rx;
+	unsigned int i;
+	u32 sts;
+	int ret;
+
+	regmap_write(samsung->regmap, DPHY_SC_GNR_CON1, T_PHY_READY(0x1450));
+	regmap_update_bits(samsung->regmap, DPHY_SC_GNR_CON0,
+			   PHY_ENABLE, PHY_ENABLE);
+
+	for (i = 0; i < rx->lanes; i++) {
+		regmap_write(samsung->regmap, rx_data_lane_gnr_con1[i],
+			     T_PHY_READY(0x1450));
+		regmap_update_bits(samsung->regmap, rx_data_lane_gnr_con0[i],
+				   PHY_ENABLE, PHY_ENABLE);
+	}
+
+	ret = regmap_read_poll_timeout(samsung->regmap, DPHY_SC_GNR_CON0,
+				       sts, sts & PHY_READY, 200, 4000);
+	if (ret) {
+		dev_err(samsung->dev, "RX clock lane not ready\n");
+		goto err_lane_disable;
+	}
+
+	for (i = 0; i < rx->lanes; i++) {
+		ret = regmap_read_poll_timeout(samsung->regmap,
+					       rx_data_lane_gnr_con0[i],
+					       sts, sts & PHY_READY,
+					       200, 2000);
+		if (ret) {
+			dev_err(samsung->dev, "RX data lane %u not ready\n", i);
+			goto err_lane_disable;
+		}
+	}
+
+	return 0;
+
+err_lane_disable:
+	samsung_mipi_dphy_rx_lane_disable(samsung);
+	return ret;
+}
+
 static void samsung_mipi_dcphy_bias_block_enable(struct samsung_mipi_dcphy *samsung)
 {
 	regmap_write(samsung->regmap, BIAS_CON0, I_DEV_DIV_6 | I_RES_100_2UA);
@@ -988,6 +1300,55 @@ static void samsung_mipi_dcphy_bias_block_enable(struct samsung_mipi_dcphy *sams
 						 REG_400M_400MV | REG_645M_645MV);
 }
 
+static int samsung_mipi_dphy_rx_power_on(struct samsung_mipi_dcphy *samsung)
+{
+	struct samsung_mipi_phy *rx = &samsung->rx;
+	int ret;
+
+	if (!rx->hs_clk_rate || !rx->lanes)
+		return -EINVAL;
+
+	reset_control_assert(samsung->s_phy_rst);
+
+	/* default output voltage select:
+	 * dphy: 400mv
+	 * cphy: 530mv
+	 */
+	regmap_update_bits(samsung->regmap, BIAS_CON4,
+			   I_MUX_SEL_MASK, I_MUX_400MV);
+
+	samsung_mipi_dphy_rx_config_common(samsung);
+
+	ret = samsung_mipi_dphy_rx_config_settle(samsung);
+	if (ret)
+		goto out_deassert;
+
+	ret = samsung_mipi_dphy_rx_lane_enable(samsung);
+
+out_deassert:
+	reset_control_deassert(samsung->s_phy_rst);
+
+	return ret;
+}
+
+static int samsung_mipi_dphy_rx_power_off(struct samsung_mipi_dcphy *samsung)
+{
+	reset_control_assert(samsung->s_phy_rst);
+
+	samsung_mipi_dphy_rx_lane_disable(samsung);
+
+	reset_control_deassert(samsung->s_phy_rst);
+
+	/*
+	 * Let the lanes settle out of reset before the receiver may be
+	 * brought up again. The delay follows the vendor driver; the TRM
+	 * does not document a teardown sequence.
+	 */
+	usleep_range(500, 1000);
+
+	return 0;
+}
+
 static void samsung_mipi_dphy_tx_lane_enable(struct samsung_mipi_dcphy *samsung)
 {
 	regmap_write(samsung->regmap, DPHY_MC_GNR_CON1, T_PHY_READY(0x2000));
@@ -1516,17 +1877,40 @@ static int samsung_mipi_dcphy_exit(struct phy *phy)
 static int samsung_mipi_dcphy_rx_configure(struct phy *phy,
 					   union phy_configure_opts *opts)
 {
-	return -EOPNOTSUPP;
+	struct samsung_mipi_dcphy *samsung = phy_get_drvdata(phy);
+
+	samsung->rx.lanes = opts->mipi_dphy.lanes > 4 ? 4 : opts->mipi_dphy.lanes;
+
+	/* The sensor supplies the link clock, so the PLL stays off. */
+	samsung->rx.hs_clk_rate = opts->mipi_dphy.hs_clk_rate;
+
+	return 0;
 }
 
 static int samsung_mipi_dcphy_rx_power_on(struct phy *phy)
 {
-	return -EOPNOTSUPP;
+	struct samsung_mipi_dcphy *samsung = phy_get_drvdata(phy);
+
+	switch (samsung->type) {
+	case PHY_TYPE_DPHY:
+		return samsung_mipi_dphy_rx_power_on(samsung);
+	default:
+		/* CPHY part to be implemented later */
+		return -EOPNOTSUPP;
+	}
 }
 
 static int samsung_mipi_dcphy_rx_power_off(struct phy *phy)
 {
-	return -EOPNOTSUPP;
+	struct samsung_mipi_dcphy *samsung = phy_get_drvdata(phy);
+
+	switch (samsung->type) {
+	case PHY_TYPE_DPHY:
+		return samsung_mipi_dphy_rx_power_off(samsung);
+	default:
+		/* CPHY part to be implemented later */
+		return -EOPNOTSUPP;
+	}
 }
 
 static const struct phy_ops samsung_mipi_dcphy_tx_ops = {

-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip