* [PATCH v8 01/13] hw/char/cadence_uart: Reduce the size of MMIO to 0x80
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 02/13] hw/char/cadence_uart: Add BXRS register definition Kuan-Jui Chiu
` (11 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
We don't need to reserve 4 KiB for MMIO since the last register implemented
is R_TTRIG at address 0x44
This patch reduces the size of MMIO to 0x80 from 0x1000
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/char/cadence_uart.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/hw/char/cadence_uart.c b/hw/char/cadence_uart.c
index eff6a3c4d1..8e23a378c4 100644
--- a/hw/char/cadence_uart.c
+++ b/hw/char/cadence_uart.c
@@ -559,7 +559,7 @@ static void cadence_uart_init(Object *obj)
SysBusDevice *sbd = SYS_BUS_DEVICE(obj);
CadenceUARTState *s = CADENCE_UART(obj);
- memory_region_init_io(&s->iomem, obj, &uart_ops, s, "uart", 0x1000);
+ memory_region_init_io(&s->iomem, obj, &uart_ops, s, "uart", 0x80);
sysbus_init_mmio(sbd, &s->iomem);
sysbus_init_irq(sbd, &s->irq);
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 02/13] hw/char/cadence_uart: Add BXRS register definition
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 01/13] hw/char/cadence_uart: Reduce the size of MMIO to 0x80 Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 03/13] hw/arm/ax3000-soc: Enable BXRS support of CADENCE UART Kuan-Jui Chiu
` (10 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
The RXBS (RX FIFO Byte Status) register at 0x48 is only exposed to
the guest when the brk_support property is set, so the accessible size
should be CADENCE_UART_R_MAX_BRK in that case and CADENCE_UART_R_MAX
otherwise.
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/char/cadence_uart.c | 15 ++++++++++++---
include/hw/char/cadence_uart.h | 4 +++-
2 files changed, 15 insertions(+), 4 deletions(-)
diff --git a/hw/char/cadence_uart.c b/hw/char/cadence_uart.c
index 8e23a378c4..8746a96619 100644
--- a/hw/char/cadence_uart.c
+++ b/hw/char/cadence_uart.c
@@ -120,6 +120,13 @@
#define R_PMIN (0x3C/4)
#define R_PWID (0x40/4)
#define R_TTRIG (0x44/4)
+#define R_RXBS (0x48/4)
+
+/* Number of registers reachable by the guest, depending on brk_support */
+static inline unsigned int uart_r_max(const CadenceUARTState *s)
+{
+ return s->brk_support ? CADENCE_UART_R_MAX_BRK : CADENCE_UART_R_MAX;
+}
static void uart_update_status(CadenceUARTState *s)
@@ -424,7 +431,7 @@ static MemTxResult uart_write(void *opaque, hwaddr offset,
DB_PRINT(" offset:%x data:%08x\n", (unsigned)offset, (unsigned)value);
offset >>= 2;
- if (offset >= CADENCE_UART_R_MAX) {
+ if (offset >= uart_r_max(s)) {
return MEMTX_DECODE_ERROR;
}
switch (offset) {
@@ -492,7 +499,7 @@ static MemTxResult uart_read(void *opaque, hwaddr offset,
}
offset >>= 2;
- if (offset >= CADENCE_UART_R_MAX) {
+ if (offset >= uart_r_max(s)) {
return MEMTX_DECODE_ERROR;
}
if (offset == R_TX_RX) {
@@ -523,6 +530,7 @@ static void cadence_uart_reset_init(Object *obj, ResetType type)
s->r[R_BRGR] = 0x0000028B;
s->r[R_BDIV] = 0x0000000F;
s->r[R_TTRIG] = 0x00000020;
+ s->r[R_RXBS] = 0;
}
static void cadence_uart_reset_hold(Object *obj, ResetType type)
@@ -603,7 +611,7 @@ static const VMStateDescription vmstate_cadence_uart = {
.pre_load = cadence_uart_pre_load,
.post_load = cadence_uart_post_load,
.fields = (const VMStateField[]) {
- VMSTATE_UINT32_ARRAY(r, CadenceUARTState, CADENCE_UART_R_MAX),
+ VMSTATE_UINT32_ARRAY(r, CadenceUARTState, CADENCE_UART_R_MAX_BRK),
VMSTATE_UINT8_ARRAY(rx_fifo, CadenceUARTState,
CADENCE_UART_RX_FIFO_SIZE),
VMSTATE_UINT8_ARRAY(tx_fifo, CadenceUARTState,
@@ -619,6 +627,7 @@ static const VMStateDescription vmstate_cadence_uart = {
static const Property cadence_uart_properties[] = {
DEFINE_PROP_CHR("chardev", CadenceUARTState, chr),
+ DEFINE_PROP_BOOL("brk-support", CadenceUARTState, brk_support, false),
};
static void cadence_uart_class_init(ObjectClass *klass, const void *data)
diff --git a/include/hw/char/cadence_uart.h b/include/hw/char/cadence_uart.h
index 751a751248..1d5fc7f328 100644
--- a/include/hw/char/cadence_uart.h
+++ b/include/hw/char/cadence_uart.h
@@ -30,6 +30,7 @@
#define CADENCE_UART_TX_FIFO_SIZE 16
#define CADENCE_UART_R_MAX (0x48/4)
+#define CADENCE_UART_R_MAX_BRK (0x4C/4)
#define TYPE_CADENCE_UART "cadence_uart"
OBJECT_DECLARE_SIMPLE_TYPE(CadenceUARTState, CADENCE_UART)
@@ -40,7 +41,7 @@ struct CadenceUARTState {
/*< public >*/
MemoryRegion iomem;
- uint32_t r[CADENCE_UART_R_MAX];
+ uint32_t r[CADENCE_UART_R_MAX_BRK];
uint8_t rx_fifo[CADENCE_UART_RX_FIFO_SIZE];
uint8_t tx_fifo[CADENCE_UART_TX_FIFO_SIZE];
uint32_t rx_wpos;
@@ -51,6 +52,7 @@ struct CadenceUARTState {
qemu_irq irq;
QEMUTimer *fifo_trigger_handle;
Clock *refclk;
+ bool brk_support;
};
#endif
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 03/13] hw/arm/ax3000-soc: Enable BXRS support of CADENCE UART
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 01/13] hw/char/cadence_uart: Reduce the size of MMIO to 0x80 Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 02/13] hw/char/cadence_uart: Add BXRS register definition Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 04/13] hw/arm: Rename ax3000-boards as axiado-boards Kuan-Jui Chiu
` (9 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
In order to access BXRS (RX FIFO Byte Status) register at runtime, set
property brk-support of CADENCE UART to true
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/arm/ax3000-soc.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/hw/arm/ax3000-soc.c b/hw/arm/ax3000-soc.c
index ebe174fb97..7b96466860 100644
--- a/hw/arm/ax3000-soc.c
+++ b/hw/arm/ax3000-soc.c
@@ -155,6 +155,7 @@ static void ax3000_realize(DeviceState *dev, Error **errp)
for (int i = 0; i < AX3000_NUM_UARTS; i++) {
qdev_prop_set_chr(DEVICE(&s->uart[i]), "chardev", serial_hd(i));
+ qdev_prop_set_bit(DEVICE(&s->uart[i]), "brk-support", true);
if (!sysbus_realize(SYS_BUS_DEVICE(&s->uart[i]), errp)) {
return;
}
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 04/13] hw/arm: Rename ax3000-boards as axiado-boards
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (2 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 03/13] hw/arm/ax3000-soc: Enable BXRS support of CADENCE UART Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 05/13] hw/arm/ax3000: Specify SoC name in header and variable Kuan-Jui Chiu
` (8 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Rename header file ax3000-boards.h as axiado-boards.h for sharing across
different Axiado SoC series
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
Reviewed-by: Jack Wang <163wangjack@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@oss.qualcomm.com>
---
hw/arm/ax3000-boards.c | 2 +-
hw/arm/ax3000-evk.c | 2 +-
include/hw/arm/{ax3000-boards.h => axiado-boards.h} | 0
3 files changed, 2 insertions(+), 2 deletions(-)
rename include/hw/arm/{ax3000-boards.h => axiado-boards.h} (100%)
diff --git a/hw/arm/ax3000-boards.c b/hw/arm/ax3000-boards.c
index dc98ee7b71..b4e7ec6f1c 100644
--- a/hw/arm/ax3000-boards.c
+++ b/hw/arm/ax3000-boards.c
@@ -7,7 +7,7 @@
*/
#include "qemu/osdep.h"
-#include "hw/arm/ax3000-boards.h"
+#include "hw/arm/axiado-boards.h"
#include "hw/arm/boot.h"
#include "qemu/error-report.h"
#include "qom/object.h"
diff --git a/hw/arm/ax3000-evk.c b/hw/arm/ax3000-evk.c
index a170848871..f491de7521 100644
--- a/hw/arm/ax3000-evk.c
+++ b/hw/arm/ax3000-evk.c
@@ -7,7 +7,7 @@
*/
#include "qemu/osdep.h"
-#include "hw/arm/ax3000-boards.h"
+#include "hw/arm/axiado-boards.h"
static void axiado_scm3003_class_init(ObjectClass *oc, const void *data)
{
diff --git a/include/hw/arm/ax3000-boards.h b/include/hw/arm/axiado-boards.h
similarity index 100%
rename from include/hw/arm/ax3000-boards.h
rename to include/hw/arm/axiado-boards.h
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 05/13] hw/arm/ax3000: Specify SoC name in header and variable
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (3 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 04/13] hw/arm: Rename ax3000-boards as axiado-boards Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 06/13] hw/arm/ax3000-boards: Add memory guard Kuan-Jui Chiu
` (7 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@oss.qualcomm.com>
---
hw/arm/ax3000-boards.c | 2 +-
hw/arm/ax3000-evk.c | 2 +-
hw/arm/ax3000-soc.c | 4 ++--
3 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/hw/arm/ax3000-boards.c b/hw/arm/ax3000-boards.c
index b4e7ec6f1c..b3ee6c4a69 100644
--- a/hw/arm/ax3000-boards.c
+++ b/hw/arm/ax3000-boards.c
@@ -1,5 +1,5 @@
/*
- * Axiado Boards
+ * Axiado Ax3000 Boards
*
* Author: Kuan-Jui Chiu <kchiu@axiado.com>
*
diff --git a/hw/arm/ax3000-evk.c b/hw/arm/ax3000-evk.c
index f491de7521..adcad2f340 100644
--- a/hw/arm/ax3000-evk.c
+++ b/hw/arm/ax3000-evk.c
@@ -1,5 +1,5 @@
/*
- * Axiado Evaluation Kit Emulation
+ * Axiado Ax3000 Evaluation Kit Emulation
*
* Author: Kuan-Jui Chiu <kchiu@axiado.com>
*
diff --git a/hw/arm/ax3000-soc.c b/hw/arm/ax3000-soc.c
index 7b96466860..37c938d942 100644
--- a/hw/arm/ax3000-soc.c
+++ b/hw/arm/ax3000-soc.c
@@ -230,7 +230,7 @@ static void ax3000_class_init(ObjectClass *oc, const void *data)
sc->num_cpus = AX3000_NUM_CPUS;
}
-static const TypeInfo axiado_soc_types[] = {
+static const TypeInfo ax3000_soc_types[] = {
{
.name = TYPE_AX3000_SOC,
.parent = TYPE_SYS_BUS_DEVICE,
@@ -241,4 +241,4 @@ static const TypeInfo axiado_soc_types[] = {
}
};
-DEFINE_TYPES(axiado_soc_types)
+DEFINE_TYPES(ax3000_soc_types)
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 06/13] hw/arm/ax3000-boards: Add memory guard
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (4 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 05/13] hw/arm/ax3000: Specify SoC name in header and variable Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 07/13] hw/arm/ax3000-boards: Add modify_dtb for discontiguous memory Kuan-Jui Chiu
` (6 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Ax3000 SoC reserves 3136 MiB memory for access totally
QEMU allows -m option to set the ram_size which would cause the
inconsistent size issue while running in QMP
This patch adds a guard to check if ram_size is different from RAM size
of SoC and setup the default_ram_size
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/arm/ax3000-boards.c | 9 +++++++++
include/hw/arm/ax3000-soc.h | 1 +
2 files changed, 10 insertions(+)
diff --git a/hw/arm/ax3000-boards.c b/hw/arm/ax3000-boards.c
index b3ee6c4a69..bc1f818d74 100644
--- a/hw/arm/ax3000-boards.c
+++ b/hw/arm/ax3000-boards.c
@@ -9,6 +9,7 @@
#include "qemu/osdep.h"
#include "hw/arm/axiado-boards.h"
#include "hw/arm/boot.h"
+#include "qemu/cutils.h"
#include "qemu/error-report.h"
#include "qom/object.h"
@@ -21,6 +22,13 @@ static void ax3000_machine_init(MachineState *machine)
{
Ax3000MachineState *ams = AX3000_MACHINE(machine);
+ if (machine->ram_size != AX3000_DRAM_SIZE) {
+ g_autofree char *size_str = size_to_str(AX3000_DRAM_SIZE);
+
+ error_report("Invalid RAM size, should be %s", size_str);
+ exit(1);
+ }
+
ams->soc = AX3000_SOC(object_new(TYPE_AX3000_SOC));
object_property_add_child(OBJECT(machine), "soc", OBJECT(ams->soc));
sysbus_realize_and_unref(SYS_BUS_DEVICE(ams->soc), &error_fatal);
@@ -38,6 +46,7 @@ static void ax3000_machine_class_init(ObjectClass *oc, const void *data)
mc->min_cpus = AX3000_NUM_CPUS;
mc->max_cpus = AX3000_NUM_CPUS;
mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-a53");
+ mc->default_ram_size = AX3000_DRAM_SIZE;
}
static const TypeInfo ax3000_machine_types[] = {
diff --git a/include/hw/arm/ax3000-soc.h b/include/hw/arm/ax3000-soc.h
index 344fcb6f3c..4987ee3834 100644
--- a/include/hw/arm/ax3000-soc.h
+++ b/include/hw/arm/ax3000-soc.h
@@ -25,6 +25,7 @@ OBJECT_DECLARE_TYPE(Ax3000SoCState, Ax3000SoCClass, AX3000_SOC)
#define AX3000_DRAM0_SIZE (1088 * MiB)
#define AX3000_DRAM1_BASE 0x400000000
#define AX3000_DRAM1_SIZE (2 * GiB)
+#define AX3000_DRAM_SIZE (AX3000_DRAM0_SIZE + AX3000_DRAM1_SIZE)
#define AX3000_GIC_DIST_BASE 0x80300000
#define AX3000_GIC_DIST_SIZE (64 * KiB)
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 07/13] hw/arm/ax3000-boards: Add modify_dtb for discontiguous memory
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (5 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 06/13] hw/arm/ax3000-boards: Add memory guard Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 08/13] hw/arm/ax3000-boards: Remove redundant pointer from struct Kuan-Jui Chiu
` (5 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Ax3000 SoC has two memory banks:
1. 0x3C000000 with 1088 MiB
2. 0x400000000 wit 2 GiB
When user boot kernel directly on axiado-scm3003 models, kernel would
believe these memory are contiguous which cause the crash
This patch add modify_dtb callback to revise the memory block
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/arm/ax3000-boards.c | 48 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 48 insertions(+)
diff --git a/hw/arm/ax3000-boards.c b/hw/arm/ax3000-boards.c
index bc1f818d74..75e0aedb4d 100644
--- a/hw/arm/ax3000-boards.c
+++ b/hw/arm/ax3000-boards.c
@@ -12,10 +12,58 @@
#include "qemu/cutils.h"
#include "qemu/error-report.h"
#include "qom/object.h"
+#include "system/device_tree.h"
+
+/*
+ * arm_load_dtb() drops every /memory node found in the DTB and replaces them
+ * with a single node spanning [loader_start, loader_start + ram_size). The
+ * AX3000 DRAM is split into two banks with the MMIO region in between, so the
+ * generated node would describe unbacked addresses as RAM. Describe the banks
+ * ourselves instead.
+ */
+static void ax3000_modify_dtb(const struct arm_boot_info *info, void *fdt)
+{
+ g_autofree char *nodename = NULL;
+ uint64_t reg[AX3000_NUM_BANKS * 2];
+ char **node_path;
+ Error *err = NULL;
+ int i;
+
+ node_path = qemu_fdt_node_unit_path(fdt, "memory", &err);
+ if (err) {
+ error_report_err(err);
+ exit(1);
+ }
+ for (i = 0; node_path[i]; i++) {
+ if (g_str_has_prefix(node_path[i], "/memory")) {
+ qemu_fdt_nop_node(fdt, node_path[i]);
+ }
+ }
+ g_strfreev(node_path);
+
+ const struct {
+ hwaddr addr;
+ size_t size;
+ } dram_table[] = {
+ { AX3000_DRAM0_BASE, AX3000_DRAM0_SIZE},
+ { AX3000_DRAM1_BASE, AX3000_DRAM1_SIZE}
+ };
+
+ for (i = 0; i < AX3000_NUM_BANKS; i++) {
+ reg[i * 2] = cpu_to_be64(dram_table[i].addr);
+ reg[i * 2 + 1] = cpu_to_be64(dram_table[i].size);
+ }
+
+ nodename = g_strdup_printf("/memory@%" HWADDR_PRIx, dram_table[0].addr);
+ qemu_fdt_add_subnode(fdt, nodename);
+ qemu_fdt_setprop_string(fdt, nodename, "device_type", "memory");
+ qemu_fdt_setprop(fdt, nodename, "reg", reg, sizeof(reg));
+}
static struct arm_boot_info ax3000_binfo = {
.loader_start = AX3000_DRAM0_BASE,
.board_id = -1,
+ .modify_dtb = ax3000_modify_dtb,
};
static void ax3000_machine_init(MachineState *machine)
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 08/13] hw/arm/ax3000-boards: Remove redundant pointer from struct
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (6 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 07/13] hw/arm/ax3000-boards: Add modify_dtb for discontiguous memory Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 09/13] hw/arm/ax3000-soc: Revise variables accodring to QEMU idioms Kuan-Jui Chiu
` (4 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Since ax3000-boards is bound with Ax3000 SoC, we don't need to have a
pointer in struct for SoC type
This patch remove pointer soc from Ax3000MachineState and create instance
in init() directly
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/arm/ax3000-boards.c | 10 +++++-----
include/hw/arm/axiado-boards.h | 1 -
2 files changed, 5 insertions(+), 6 deletions(-)
diff --git a/hw/arm/ax3000-boards.c b/hw/arm/ax3000-boards.c
index 75e0aedb4d..3ca4a6f93a 100644
--- a/hw/arm/ax3000-boards.c
+++ b/hw/arm/ax3000-boards.c
@@ -68,7 +68,7 @@ static struct arm_boot_info ax3000_binfo = {
static void ax3000_machine_init(MachineState *machine)
{
- Ax3000MachineState *ams = AX3000_MACHINE(machine);
+ Ax3000SoCState *s;
if (machine->ram_size != AX3000_DRAM_SIZE) {
g_autofree char *size_str = size_to_str(AX3000_DRAM_SIZE);
@@ -77,12 +77,12 @@ static void ax3000_machine_init(MachineState *machine)
exit(1);
}
- ams->soc = AX3000_SOC(object_new(TYPE_AX3000_SOC));
- object_property_add_child(OBJECT(machine), "soc", OBJECT(ams->soc));
- sysbus_realize_and_unref(SYS_BUS_DEVICE(ams->soc), &error_fatal);
+ s = AX3000_SOC(object_new_with_props(TYPE_AX3000_SOC, OBJECT(machine),
+ "soc", &error_fatal, NULL));
+ sysbus_realize_and_unref(SYS_BUS_DEVICE(s), &error_fatal);
ax3000_binfo.ram_size = machine->ram_size;
- arm_load_kernel(&ams->soc->cpu[0], machine, &ax3000_binfo);
+ arm_load_kernel(&s->cpu[0], machine, &ax3000_binfo);
}
static void ax3000_machine_class_init(ObjectClass *oc, const void *data)
diff --git a/include/hw/arm/axiado-boards.h b/include/hw/arm/axiado-boards.h
index 4a632661e1..566f22cd96 100644
--- a/include/hw/arm/axiado-boards.h
+++ b/include/hw/arm/axiado-boards.h
@@ -18,7 +18,6 @@ OBJECT_DECLARE_TYPE(Ax3000MachineState, Ax3000MachineClass, AX3000_MACHINE)
typedef struct Ax3000MachineState {
MachineState parent;
- Ax3000SoCState *soc;
} Ax3000MachineState;
typedef struct Ax3000MachineClass {
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 09/13] hw/arm/ax3000-soc: Revise variables accodring to QEMU idioms
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (7 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 08/13] hw/arm/ax3000-boards: Remove redundant pointer from struct Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 10/13] hw/arm: Add Axiado SoC AX3005 Kuan-Jui Chiu
` (3 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
1. Change the first declaration of struct to parent_obj/parent_class
2. Remove unnecessary typedef since macros add it automatically
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
include/hw/arm/ax3000-soc.h | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/include/hw/arm/ax3000-soc.h b/include/hw/arm/ax3000-soc.h
index 4987ee3834..e09cd56c30 100644
--- a/include/hw/arm/ax3000-soc.h
+++ b/include/hw/arm/ax3000-soc.h
@@ -60,8 +60,8 @@ enum Ax3000Configuration {
AX3000_NUM_GPIOS = 8,
};
-typedef struct Ax3000SoCState {
- SysBusDevice parent;
+struct Ax3000SoCState {
+ SysBusDevice parent_obj;
ARMCPU cpu[AX3000_NUM_CPUS];
GICv3State gic;
@@ -70,13 +70,13 @@ typedef struct Ax3000SoCState {
CadenceUARTState uart[AX3000_NUM_UARTS];
CadenceGPIOState gpio[AX3000_NUM_GPIOS];
AxiadoSDHCIState sdhci0;
-} Ax3000SoCState;
+};
-typedef struct Ax3000SoCClass {
- SysBusDeviceClass parent;
+struct Ax3000SoCClass {
+ SysBusDeviceClass parent_class;
uint32_t num_cpus;
-} Ax3000SoCClass;
+};
enum Ax3000Irqs {
AX3000_UART0_IRQ = 112,
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 10/13] hw/arm: Add Axiado SoC AX3005
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (8 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 09/13] hw/arm/ax3000-soc: Revise variables accodring to QEMU idioms Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 11/13] hw/arm: Add Axiado Ax3005 EVB Kuan-Jui Chiu
` (2 subsequent siblings)
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
This patch adds new model for Axiado SoC AX3005 which supports
4 Cortex-A53 ARM64 CPUs
Arm Generic Interrupt Controller v3
9 Cadence UARTs
1 SDHCI controller with PHY
8 Cadence GPIOs
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
MAINTAINERS | 3 +
hw/arm/ax3005-soc.c | 226 ++++++++++++++++++++++++++++++++++++
hw/arm/meson.build | 3 +-
include/hw/arm/ax3005-soc.h | 102 ++++++++++++++++
4 files changed, 333 insertions(+), 1 deletion(-)
create mode 100644 hw/arm/ax3005-soc.c
create mode 100644 include/hw/arm/ax3005-soc.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 15942aaba3..e5f37262cf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1324,11 +1324,14 @@ F: rust/hw/char/pl011/
Axiado SoCs and EVKs
M: Kuan-Jui Chiu <kchiu@axiado.com>
+M: Prasad Bolisetty <pbolisetty@axiado.com>
L: qemu-arm@nongnu.org
S: Maintained
F: hw/arm/ax3000*.c
+F: hw/arm/ax3005*.c
F: hw/*/axiado*.c
F: include/hw/arm/ax3000*.h
+F: include/hw/arm/ax3005*.h
F: include/hw/*/axiado*.h
AVR Machines
diff --git a/hw/arm/ax3005-soc.c b/hw/arm/ax3005-soc.c
new file mode 100644
index 0000000000..e555b156f4
--- /dev/null
+++ b/hw/arm/ax3005-soc.c
@@ -0,0 +1,226 @@
+/*
+ * Axiado SoC AX3005
+ *
+ * Author: Kuan-Jui Chiu <kchiu@axiado.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#include "qemu/osdep.h"
+#include "system/address-spaces.h"
+#include "hw/arm/bsa.h"
+#include "hw/arm/ax3005-soc.h"
+#include "hw/misc/unimp.h"
+#include "system/system.h"
+#include "qobject/qlist.h"
+#include "qom/object.h"
+#include "hw/core/boards.h"
+
+static void ax3005_init(Object *obj)
+{
+ Ax3005SoCState *s = AX3005_SOC(obj);
+ Ax3005SoCClass *sc = AX3005_SOC_GET_CLASS(s);
+
+ for (int i = 0; i < sc->num_cpus; i++) {
+ g_autofree char *name = g_strdup_printf("cpu%d", i);
+ object_initialize_child(obj, name, &s->cpu[i],
+ ARM_CPU_TYPE_NAME("cortex-a53"));
+ }
+
+ object_initialize_child(obj, "gic", &s->gic, gicv3_class_name());
+
+ for (int i = 0; i < AX3005_NUM_UARTS; i++) {
+ g_autofree char *name = g_strdup_printf("uart%d", i);
+ object_initialize_child(obj, name, &s->uart[i], TYPE_CADENCE_UART);
+ }
+
+ object_initialize_child(obj, "sdhci0", &s->sdhci0, TYPE_AXIADO_SDHCI);
+
+ for (int i = 0; i < AX3005_NUM_GPIOS; i++) {
+ g_autofree char *name = g_strdup_printf("gpio%d", i);
+ object_initialize_child(obj, name, &s->gpio[i], TYPE_CADENCE_GPIO);
+ }
+}
+
+static void ax3005_realize(DeviceState *dev, Error **errp)
+{
+ Ax3005SoCState *s = AX3005_SOC(dev);
+ Ax3005SoCClass *sc = AX3005_SOC_GET_CLASS(s);
+ SysBusDevice *gic_sbd = SYS_BUS_DEVICE(&s->gic);
+ DeviceState *gic_dev = DEVICE(&s->gic);
+ QList *redist_region_count;
+ SysBusDevice *sdhci0_sbd;
+ DeviceState *card;
+ DriveInfo *dinfo;
+
+ /* CPUs */
+ for (int i = 0; i < sc->num_cpus; i++) {
+ object_property_set_int(OBJECT(&s->cpu[i]), "cntfrq", 1000000000,
+ &error_abort);
+
+ if (!qdev_realize(DEVICE(&s->cpu[i]), NULL, errp)) {
+ return;
+ }
+ }
+
+ /* GIC */
+ qdev_prop_set_uint32(gic_dev, "num-cpu", sc->num_cpus);
+ qdev_prop_set_uint32(gic_dev, "num-irq",
+ AX3005_NUM_IRQS + GIC_INTERNAL);
+
+ redist_region_count = qlist_new();
+ qlist_append_int(redist_region_count, sc->num_cpus);
+ qdev_prop_set_array(gic_dev, "redist-region-count", redist_region_count);
+
+ if (!sysbus_realize(gic_sbd, errp)) {
+ return;
+ }
+
+ sysbus_mmio_map(gic_sbd, 0, AX3005_GIC_DIST_BASE);
+ sysbus_mmio_map(gic_sbd, 1, AX3005_GIC_REDIST_BASE);
+
+ /*
+ * Mapping from the output timer irq lines from the CPU to the
+ * GIC PPI inputs.
+ */
+ const int timer_irqs[] = {
+ [GTIMER_PHYS] = ARCH_TIMER_NS_EL1_IRQ,
+ [GTIMER_VIRT] = ARCH_TIMER_VIRT_IRQ,
+ [GTIMER_HYP] = ARCH_TIMER_NS_EL2_IRQ,
+ [GTIMER_SEC] = ARCH_TIMER_S_EL1_IRQ
+ };
+
+ /*
+ * Wire the outputs from each CPU's generic timer and the GICv3
+ * maintenance interrupt signal to the appropriate GIC PPI inputs, and
+ * the GIC's IRQ/FIQ interrupt outputs to the CPU's inputs.
+ */
+ for (int i = 0; i < sc->num_cpus; i++) {
+ DeviceState *cpu_dev = DEVICE(&s->cpu[i]);
+ int intidbase = AX3005_NUM_IRQS + i * GIC_INTERNAL;
+ qemu_irq irq;
+
+ for (int j = 0; j < ARRAY_SIZE(timer_irqs); j++) {
+ irq = qdev_get_gpio_in(gic_dev, intidbase + timer_irqs[j]);
+ qdev_connect_gpio_out(cpu_dev, j, irq);
+ }
+
+ irq = qdev_get_gpio_in(gic_dev, intidbase + ARCH_GIC_MAINT_IRQ);
+ qdev_connect_gpio_out_named(cpu_dev, "gicv3-maintenance-interrupt",
+ 0, irq);
+
+ sysbus_connect_irq(gic_sbd, i,
+ qdev_get_gpio_in(cpu_dev, ARM_CPU_IRQ));
+ sysbus_connect_irq(gic_sbd, i + sc->num_cpus,
+ qdev_get_gpio_in(cpu_dev, ARM_CPU_FIQ));
+ sysbus_connect_irq(gic_sbd, i + 2 * sc->num_cpus,
+ qdev_get_gpio_in(cpu_dev, ARM_CPU_VIRQ));
+ sysbus_connect_irq(gic_sbd, i + 3 * sc->num_cpus,
+ qdev_get_gpio_in(cpu_dev, ARM_CPU_VFIQ));
+ }
+
+ /* DRAM */
+ memory_region_init_ram(&s->dram, OBJECT(s), "dram", AX3005_DRAM_SIZE,
+ &error_fatal);
+ memory_region_add_subregion(get_system_memory(), AX3005_DRAM_BASE,
+ &s->dram);
+
+ /* UARTs */
+ const struct {
+ hwaddr addr;
+ unsigned int irq;
+ } serial_table[] = {
+ { AX3005_UART0_BASE, AX3005_UART0_IRQ },
+ { AX3005_UART1_BASE, AX3005_UART1_IRQ },
+ { AX3005_UART2_BASE, AX3005_UART2_IRQ },
+ { AX3005_UART3_BASE, AX3005_UART3_IRQ },
+ { AX3005_UART4_BASE, AX3005_UART4_IRQ },
+ { AX3005_UART5_BASE, AX3005_UART5_IRQ },
+ { AX3005_UART6_BASE, AX3005_UART6_IRQ },
+ { AX3005_UART7_BASE, AX3005_UART7_IRQ },
+ { AX3005_UART8_BASE, AX3005_UART8_IRQ }
+ };
+
+ for (int i = 0; i < AX3005_NUM_UARTS; i++) {
+ qdev_prop_set_chr(DEVICE(&s->uart[i]), "chardev", serial_hd(i));
+ qdev_prop_set_bit(DEVICE(&s->uart[i]), "brk-support", true);
+ if (!sysbus_realize(SYS_BUS_DEVICE(&s->uart[i]), errp)) {
+ return;
+ }
+
+ sysbus_mmio_map(SYS_BUS_DEVICE(&s->uart[i]), 0, serial_table[i].addr);
+ sysbus_connect_irq(SYS_BUS_DEVICE(&s->uart[i]), 0,
+ qdev_get_gpio_in(gic_dev, serial_table[i].irq));
+ }
+
+ /* Timer control */
+ create_unimplemented_device("ax3005.timerctrl", AX3005_TIMER_CTRL, 32);
+
+ /* SDHCI */
+ sdhci0_sbd = SYS_BUS_DEVICE(&s->sdhci0);
+ if (!sysbus_realize(sdhci0_sbd, errp)) {
+ return;
+ }
+
+ sysbus_mmio_map(sdhci0_sbd, 0, AX3005_SDHCI0_BASE);
+ sysbus_mmio_map(sdhci0_sbd, 1, AX3005_EMMC_PHY_BASE);
+ sysbus_connect_irq(sdhci0_sbd, 0,
+ qdev_get_gpio_in(gic_dev, AX3005_SDHCI0_IRQ));
+
+ dinfo = drive_get(IF_SD, 0, 0);
+ if (dinfo) {
+ card = qdev_new(TYPE_SD_CARD);
+ qdev_prop_set_drive_err(card, "drive",
+ blk_by_legacy_dinfo(dinfo),
+ &error_fatal);
+ qdev_realize_and_unref(card, s->sdhci0.sd_bus, &error_fatal);
+ }
+
+ /* GPIOs */
+ const struct {
+ hwaddr addr;
+ unsigned int irq;
+ } gpio_table[] = {
+ { AX3005_GPIO0_BASE, AX3005_GPIO0_IRQ },
+ { AX3005_GPIO1_BASE, AX3005_GPIO1_IRQ },
+ { AX3005_GPIO2_BASE, AX3005_GPIO2_IRQ },
+ { AX3005_GPIO3_BASE, AX3005_GPIO3_IRQ },
+ { AX3005_GPIO4_BASE, AX3005_GPIO4_IRQ },
+ { AX3005_GPIO5_BASE, AX3005_GPIO5_IRQ },
+ { AX3005_GPIO6_BASE, AX3005_GPIO6_IRQ },
+ { AX3005_GPIO7_BASE, AX3005_GPIO7_IRQ }
+ };
+
+ for (int i = 0; i < AX3005_NUM_GPIOS; i++) {
+ if (!sysbus_realize(SYS_BUS_DEVICE(&s->gpio[i]), errp)) {
+ return;
+ }
+
+ sysbus_mmio_map(SYS_BUS_DEVICE(&s->gpio[i]), 0, gpio_table[i].addr);
+ sysbus_connect_irq(SYS_BUS_DEVICE(&s->gpio[i]), 0,
+ qdev_get_gpio_in(gic_dev, gpio_table[i].irq));
+ }
+}
+
+static void ax3005_class_init(ObjectClass *oc, const void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(oc);
+ Ax3005SoCClass *sc = AX3005_SOC_CLASS(oc);
+
+ dc->desc = "Axiado SoC AX3005";
+ dc->realize = ax3005_realize;
+ sc->num_cpus = AX3005_NUM_CPUS;
+}
+
+static const TypeInfo ax3005_soc_types[] = {
+ {
+ .name = TYPE_AX3005_SOC,
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(Ax3005SoCState),
+ .instance_init = ax3005_init,
+ .class_size = sizeof(Ax3005SoCClass),
+ .class_init = ax3005_class_init,
+ }
+};
+
+DEFINE_TYPES(ax3005_soc_types)
diff --git a/hw/arm/meson.build b/hw/arm/meson.build
index f3c1b0e00f..f54aaffef2 100644
--- a/hw/arm/meson.build
+++ b/hw/arm/meson.build
@@ -113,7 +113,8 @@ arm_common_ss.add(when: 'CONFIG_VERSATILE', if_true: files('versatilepb.c'))
arm_common_ss.add(when: 'CONFIG_VEXPRESS', if_true: files('vexpress.c'))
arm_common_ss.add(when: ['CONFIG_AXIADO_SOC', 'TARGET_AARCH64'], if_true: files(
- 'ax3000-soc.c'))
+ 'ax3000-soc.c',
+ 'ax3005-soc.c'))
arm_common_ss.add(when: ['CONFIG_AXIADO_EVK', 'TARGET_AARCH64'], if_true: files(
'ax3000-boards.c',
'ax3000-evk.c'))
diff --git a/include/hw/arm/ax3005-soc.h b/include/hw/arm/ax3005-soc.h
new file mode 100644
index 0000000000..e9faa80dbd
--- /dev/null
+++ b/include/hw/arm/ax3005-soc.h
@@ -0,0 +1,102 @@
+/*
+ * Axiado SoC AX3005
+ *
+ * Author: Kuan-Jui Chiu <kchiu@axiado.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#ifndef AXIADO_AX3005_H
+#define AXIADO_AX3005_H
+
+#include "cpu.h"
+#include "hw/intc/arm_gicv3_common.h"
+#include "hw/char/cadence_uart.h"
+#include "hw/gpio/cadence_gpio.h"
+#include "hw/sd/axiado_sdhci.h"
+#include "hw/core/sysbus.h"
+#include "qemu/units.h"
+
+#define TYPE_AX3005_SOC "ax3005"
+OBJECT_DECLARE_TYPE(Ax3005SoCState, Ax3005SoCClass, AX3005_SOC)
+
+#define AX3005_DRAM_BASE 0x80000000
+#define AX3005_DRAM_SIZE (2 * GiB)
+
+#define AX3005_GIC_DIST_BASE 0x40400000
+#define AX3005_GIC_DIST_SIZE (64 * KiB)
+#define AX3005_GIC_REDIST_BASE 0x40500000
+#define AX3005_GIC_REDIST_SIZE (768 * KiB)
+
+#define AX3005_UART0_BASE 0x33020000
+#define AX3005_UART1_BASE 0x330A0000
+#define AX3005_UART2_BASE 0x33120000
+#define AX3005_UART3_BASE 0x33020800
+#define AX3005_UART4_BASE 0x331A0400
+#define AX3005_UART5_BASE 0x33381D00
+#define AX3005_UART6_BASE 0x33381E00
+#define AX3005_UART7_BASE 0x33381F00
+#define AX3005_UART8_BASE 0x330C0000
+
+#define AX3005_SDHCI0_BASE 0x46000000
+#define AX3005_EMMC_PHY_BASE 0x33301C00
+
+#define AX3005_GPIO0_BASE 0x33000000
+#define AX3005_GPIO1_BASE 0x33080000
+#define AX3005_GPIO2_BASE 0x33100000
+#define AX3005_GPIO3_BASE 0x33180000
+#define AX3005_GPIO4_BASE 0x33200000
+#define AX3005_GPIO5_BASE 0x33280000
+#define AX3005_GPIO6_BASE 0x33300000
+#define AX3005_GPIO7_BASE 0x33380000
+
+#define AX3005_TIMER_CTRL 0x48016000
+
+enum Ax3005Configuration {
+ AX3005_NUM_CPUS = 4,
+ AX3005_NUM_IRQS = 224,
+ AX3005_NUM_UARTS = 9,
+ AX3005_NUM_GPIOS = 8,
+};
+
+struct Ax3005SoCState {
+ SysBusDevice parent_obj;
+
+ ARMCPU cpu[AX3005_NUM_CPUS];
+ GICv3State gic;
+ MemoryRegion dram;
+ CadenceUARTState uart[AX3005_NUM_UARTS];
+ CadenceGPIOState gpio[AX3005_NUM_GPIOS];
+ AxiadoSDHCIState sdhci0;
+};
+
+struct Ax3005SoCClass {
+ SysBusDeviceClass parent_class;
+
+ uint32_t num_cpus;
+};
+
+enum Ax3005Irqs {
+ AX3005_UART0_IRQ = 112,
+ AX3005_UART1_IRQ = 113,
+ AX3005_UART2_IRQ = 114,
+ AX3005_UART3_IRQ = 170,
+ AX3005_UART4_IRQ = 208,
+ AX3005_UART5_IRQ = 209,
+ AX3005_UART6_IRQ = 210,
+ AX3005_UART7_IRQ = 211,
+ AX3005_UART8_IRQ = 212,
+
+ AX3005_SDHCI0_IRQ = 123,
+
+ AX3005_GPIO0_IRQ = 183,
+ AX3005_GPIO1_IRQ = 184,
+ AX3005_GPIO2_IRQ = 185,
+ AX3005_GPIO3_IRQ = 186,
+ AX3005_GPIO4_IRQ = 187,
+ AX3005_GPIO5_IRQ = 188,
+ AX3005_GPIO6_IRQ = 189,
+ AX3005_GPIO7_IRQ = 190,
+};
+
+#endif /* AXIADO_AX3005_H */
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 11/13] hw/arm: Add Axiado Ax3005 EVB
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (9 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 10/13] hw/arm: Add Axiado SoC AX3005 Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 12/13] docs/system/arm: Document Axiado boards Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 13/13] tests/functional/aarch64: Add functional test for Axiado EVKs Kuan-Jui Chiu
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Add EVK ax3005-evb built with AX3005 SoC
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
hw/arm/ax3005-evk.c | 115 +++++++++++++++++++++++++++++++++
hw/arm/meson.build | 3 +-
include/hw/arm/axiado-boards.h | 9 +++
3 files changed, 126 insertions(+), 1 deletion(-)
create mode 100644 hw/arm/ax3005-evk.c
diff --git a/hw/arm/ax3005-evk.c b/hw/arm/ax3005-evk.c
new file mode 100644
index 0000000000..0bc309f244
--- /dev/null
+++ b/hw/arm/ax3005-evk.c
@@ -0,0 +1,115 @@
+/*
+ * Axiado Ax3005 Evaluation Kit Emulation
+ *
+ * Author: Kuan-Jui Chiu <kchiu@axiado.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#include "qemu/osdep.h"
+#include <libfdt.h>
+#include "hw/arm/axiado-boards.h"
+#include "hw/arm/boot.h"
+#include "qemu/cutils.h"
+#include "qemu/error-report.h"
+#include "qom/object.h"
+#include "system/device_tree.h"
+
+#define RAMROFS_BASE 0x90000000
+#define RAMROFS_SIZE (100 * MiB)
+
+/*
+ * Reserve the ramrofs window so that Linux keeps it out of the linear map and
+ * the phram driver can hand it to the guest as a block device. Any ramrofs
+ * reservation the supplied DTB carries is replaced, so that the reservation
+ * cannot drift away from RAMROFS_BASE.
+ */
+static void ax3005_modify_dtb(const struct arm_boot_info *info, void *fdt)
+{
+ g_autofree char *nodename = NULL;
+ uint64_t reg[2];
+ char **node_path;
+ Error *err = NULL;
+ int offset;
+ int i;
+
+ node_path = qemu_fdt_node_unit_path(fdt, "ramrofs", &err);
+ if (err) {
+ error_report_err(err);
+ exit(1);
+ }
+ for (i = 0; node_path[i]; i++) {
+ qemu_fdt_nop_node(fdt, node_path[i]);
+ }
+ g_strfreev(node_path);
+
+ offset = fdt_path_offset(fdt, "/reserved-memory");
+ if (offset < 0) {
+ qemu_fdt_add_subnode(fdt, "/reserved-memory");
+ qemu_fdt_setprop_cell(fdt, "/reserved-memory", "#address-cells", 2);
+ qemu_fdt_setprop_cell(fdt, "/reserved-memory", "#size-cells", 2);
+ qemu_fdt_setprop(fdt, "/reserved-memory", "ranges", NULL, 0);
+ } else if (fdt_address_cells(fdt, offset) != 2 ||
+ fdt_size_cells(fdt, offset) != 2) {
+ error_report("/reserved-memory must use two address and size cells");
+ exit(1);
+ }
+
+ nodename = g_strdup_printf("/reserved-memory/ramrofs@%" HWADDR_PRIx,
+ (hwaddr)RAMROFS_BASE);
+ reg[0] = cpu_to_be64(RAMROFS_BASE);
+ reg[1] = cpu_to_be64(RAMROFS_SIZE);
+
+ qemu_fdt_add_subnode(fdt, nodename);
+ qemu_fdt_setprop(fdt, nodename, "reg", reg, sizeof(reg));
+ qemu_fdt_setprop(fdt, nodename, "no-map", NULL, 0);
+}
+
+static struct arm_boot_info ax3005_binfo = {
+ .loader_start = AX3005_DRAM_BASE,
+ .board_id = -1,
+ .modify_dtb = ax3005_modify_dtb,
+};
+
+static void ax3005_evb_machine_init(MachineState *machine)
+{
+ Ax3005SoCState *s;
+
+ if (machine->ram_size != AX3005_DRAM_SIZE) {
+ g_autofree char *size_str = size_to_str(AX3005_DRAM_SIZE);
+
+ error_report("Invalid RAM size, should be %s", size_str);
+ exit(1);
+ }
+
+ s = AX3005_SOC(object_new_with_props(TYPE_AX3005_SOC, OBJECT(machine),
+ "soc", &error_fatal, NULL));
+ sysbus_realize_and_unref(SYS_BUS_DEVICE(s), &error_fatal);
+
+ ax3005_binfo.ram_size = machine->ram_size;
+ arm_load_kernel(&s->cpu[0], machine, &ax3005_binfo);
+}
+
+static void ax3005_evb_class_init(ObjectClass *oc, const void *data)
+{
+ MachineClass *mc = MACHINE_CLASS(oc);
+
+ mc->desc = "Axiado AX3005 Evaluation Board";
+ mc->init = ax3005_evb_machine_init;
+ mc->default_cpus = AX3005_NUM_CPUS;
+ mc->min_cpus = AX3005_NUM_CPUS;
+ mc->max_cpus = AX3005_NUM_CPUS;
+ mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-a53");
+ mc->default_ram_size = AX3005_DRAM_SIZE;
+}
+
+static const TypeInfo ax3005_evk_types[] = {
+ {
+ .name = TYPE_AX3005_MACHINE,
+ .parent = TYPE_MACHINE,
+ .instance_size = sizeof(Ax3005MachineState),
+ .class_init = ax3005_evb_class_init,
+ }
+};
+
+DEFINE_TYPES(ax3005_evk_types)
diff --git a/hw/arm/meson.build b/hw/arm/meson.build
index f54aaffef2..434cabdfd0 100644
--- a/hw/arm/meson.build
+++ b/hw/arm/meson.build
@@ -117,7 +117,8 @@ arm_common_ss.add(when: ['CONFIG_AXIADO_SOC', 'TARGET_AARCH64'], if_true: files(
'ax3005-soc.c'))
arm_common_ss.add(when: ['CONFIG_AXIADO_EVK', 'TARGET_AARCH64'], if_true: files(
'ax3000-boards.c',
- 'ax3000-evk.c'))
+ 'ax3000-evk.c',
+ 'ax3005-evk.c'))
arm_common_ss.add(files('boot.c'))
diff --git a/include/hw/arm/axiado-boards.h b/include/hw/arm/axiado-boards.h
index 566f22cd96..0f2c586d40 100644
--- a/include/hw/arm/axiado-boards.h
+++ b/include/hw/arm/axiado-boards.h
@@ -11,6 +11,7 @@
#include "hw/core/boards.h"
#include "hw/arm/ax3000-soc.h"
+#include "hw/arm/ax3005-soc.h"
#define TYPE_AX3000_MACHINE MACHINE_TYPE_NAME("ax3000")
OBJECT_DECLARE_TYPE(Ax3000MachineState, Ax3000MachineClass, AX3000_MACHINE)
@@ -24,4 +25,12 @@ typedef struct Ax3000MachineClass {
MachineClass parent;
} Ax3000MachineClass;
+
+#define TYPE_AX3005_MACHINE MACHINE_TYPE_NAME("ax3005-evb")
+OBJECT_DECLARE_SIMPLE_TYPE(Ax3005MachineState, AX3005_MACHINE)
+
+struct Ax3005MachineState {
+ MachineState parent;
+
+};
#endif
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 12/13] docs/system/arm: Document Axiado boards
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (10 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 11/13] hw/arm: Add Axiado Ax3005 EVB Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
2026-11-19 7:13 ` [PATCH v8 13/13] tests/functional/aarch64: Add functional test for Axiado EVKs Kuan-Jui Chiu
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
MAINTAINERS | 1 +
docs/system/arm/axiado.rst | 128 +++++++++++++++++++++++++++++++++++++
docs/system/target-arm.rst | 1 +
3 files changed, 130 insertions(+)
create mode 100644 docs/system/arm/axiado.rst
diff --git a/MAINTAINERS b/MAINTAINERS
index e5f37262cf..53e15069ed 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1333,6 +1333,7 @@ F: hw/*/axiado*.c
F: include/hw/arm/ax3000*.h
F: include/hw/arm/ax3005*.h
F: include/hw/*/axiado*.h
+F: docs/system/arm/axiado.rst
AVR Machines
-------------
diff --git a/docs/system/arm/axiado.rst b/docs/system/arm/axiado.rst
new file mode 100644
index 0000000000..bceaa77d83
--- /dev/null
+++ b/docs/system/arm/axiado.rst
@@ -0,0 +1,128 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+Axiado family boards (``axiado-scm3003``, ``ax3005-evb``)
+================================================================
+
+The Axiado AX3000 and AX3005 are Arm-based system-on-chip devices intended
+to be used as the management and security processor of a server platform,
+in the same role as a traditional Baseboard Management Controller (BMC).
+
+Two machines are modelled:
+
+- ``axiado-scm3003`` Axiado SCM3003 evaluation kit, based on the AX3000
+- ``ax3005-evb`` Axiado AX3005 evaluation board, based on the AX3005
+
+Neither SoC is supported by the upstream Linux kernel or by upstream
+U-Boot, so there is currently no way to build a bootable image for these
+machines from mainline sources. Axiado intends to publish a firmware
+package suitable for QEMU; until then no ready-to-run image is publicly
+available.
+
+Firmware download
+-----------------
+
+Images can be downloaded from the Axiado Forked OpenBMC Github release repository :
+
+ https://github.com/axiado/openbmc/releases
+
+AX3000 (``axiado-scm3003``)
+---------------------------
+
+Supported devices
+~~~~~~~~~~~~~~~~~
+
+ * SMP (4 x Cortex-A53)
+ * GICv3 interrupt controller
+ * Arm generic timers
+ * DRAM
+ * Cadence UARTs
+ * Cadence GPIO controllers
+ * SD/eMMC host controller (SDHCI) with its eMMC PHY register block
+ * Clock/reset controller (PLL) registers polled by the boot firmware
+
+Running
+~~~~~~~
+
+Boot a kernel directly on the SCM3003 evaluation kit, with an eMMC/SD
+image attached to the SD host controller:
+
+.. code-block:: bash
+
+ qemu-system-aarch64 -M axiado-scm3003 -nographic \
+ -kernel Image \
+ -dtb ax3000-scm3003-qemu.dtb \
+ -initrd obmc-phosphor-initramfs-evk-axiado-qemu.cpio.xz \
+ -serial null \
+ -serial null \
+ -serial null \
+ -serial mon:stdio \
+ -drive if=sd,file=obmc-phosphor-image-evk-axiado-qemu.wic.qcow2,format=qcow2 \
+ -append "console=ttyPS3,115200 earlycon nr_cpus=1 rootwait root=PARTLABEL=rofs-a"
+
+or boot via u-boot:
+
+.. code-block:: bash
+
+ qemu-system-aarch64 -M axiado-scm3003 -nographic \
+ -device loader,file=u-boot.bin,addr=0x3C000000,cpu-num=0 \
+ -serial null \
+ -serial null \
+ -serial null \
+ -serial mon:stdio \
+ -drive if=sd,file=obmc-phosphor-image-evk-axiado-qemu.wic.qcow2,format=qcow2
+
+AX3005 (``ax3005-evb``)
+-----------------------
+
+Supported devices
+~~~~~~~~~~~~~~~~~
+
+ * SMP (4 x Cortex-A53)
+ * GICv3 interrupt controller
+ * Arm generic timers
+ * DRAM
+ * Cadence UARTs
+ * Cadence GPIO controllers
+ * SD/eMMC host controller (SDHCI) with its eMMC PHY register block
+
+Running
+~~~~~~~
+
+Boot a kernel directly on the AX3005 evaluation board, with an eMMC/SD
+image attached to the SD host controller:
+
+.. code-block:: bash
+
+ qemu-system-aarch64 -M ax3005-evb -nographic \
+ -M ax3005-evb \
+ -kernel Image \
+ -dtb ax3005-evb-qemu.dtb \
+ -initrd obmc-phosphor-initramfs-evk-ax3005-qemu.cpio.xz \
+ -device loader,file=obmc-phosphor-image-evk-ax3005-qemu.squashfs-xz,addr=0x90000000 \
+ -serial null \
+ -serial null \
+ -serial null \
+ -serial mon:stdio \
+ -drive if=sd,file=obmc-phosphor-image-evk-ax3005-qemu.wic.qcow2,format=qcow2 \
+ -append "console=ttyPS3,115200 earlycon nr_cpus=1 root=/dev/ram rw phram.phram=ramrofs,0x90000000,0x6400000"
+
+or boot with ARM TrustZone:
+
+.. code-block:: bash
+
+ qemu-system-aarch64 -nographic \
+ -M ax3005-evb \
+ -device loader,file=bl31.bin,addr=0x88300000 \
+ -device loader,file=tee-raw.bin,addr=0x88400000 \
+ -device loader,file=u-boot.bin,addr=0x80000000 \
+ -device loader,file=fitImage,addr=0x80100000 \
+ -device loader,file=obmc-phosphor-image-evk-ax3005-qemu.squashfs-xz,addr=0x80B00000 \
+ -device loader,cpu-num=0,addr=0x88300000 \
+ -device loader,cpu-num=1,addr=0x88300000 \
+ -device loader,cpu-num=2,addr=0x88300000 \
+ -device loader,cpu-num=3,addr=0x88300000 \
+ -serial null \
+ -serial null \
+ -serial null \
+ -serial mon:stdio \
+ -drive if=sd,file=obmc-phosphor-image-evk-ax3005-qemu.wic.qcow2,format=qcow2
diff --git a/docs/system/target-arm.rst b/docs/system/target-arm.rst
index 260cd7e4d6..1b038b41de 100644
--- a/docs/system/target-arm.rst
+++ b/docs/system/target-arm.rst
@@ -80,6 +80,7 @@ Board-specific documentation
arm/versatile
arm/vexpress
arm/aspeed
+ arm/axiado
arm/bananapi_m2u.rst
arm/b-l475e-iot01a.rst
arm/sabrelite
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v8 13/13] tests/functional/aarch64: Add functional test for Axiado EVKs
2026-11-19 7:13 [PATCH v8 00/13] Add Axiado SoC AX3005 and EVB Kuan-Jui Chiu
` (11 preceding siblings ...)
2026-11-19 7:13 ` [PATCH v8 12/13] docs/system/arm: Document Axiado boards Kuan-Jui Chiu
@ 2026-11-19 7:13 ` Kuan-Jui Chiu
12 siblings, 0 replies; 14+ messages in thread
From: Kuan-Jui Chiu @ 2026-11-19 7:13 UTC (permalink / raw)
Cc: Kuan-Jui Chiu, mark.caveayland, philmd, 163wangjack,
peter.maydell, qemu-devel, qemu-arm
Introduce funtional test for boot process from the kernel to systemd
Add additional subtest to include ARM TrustedZone firmware into boot
process for ax3005-evb model
Signed-off-by: Kuan-Jui Chiu <kchiu@axiado.com>
---
MAINTAINERS | 2 +
tests/functional/aarch64/meson.build | 4 +
tests/functional/aarch64/test_ax3005_evb.py | 140 ++++++++++++++++++
.../functional/aarch64/test_axiado_scm3003.py | 62 ++++++++
4 files changed, 208 insertions(+)
create mode 100755 tests/functional/aarch64/test_ax3005_evb.py
create mode 100755 tests/functional/aarch64/test_axiado_scm3003.py
diff --git a/MAINTAINERS b/MAINTAINERS
index 53e15069ed..297c8685d6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1333,6 +1333,8 @@ F: hw/*/axiado*.c
F: include/hw/arm/ax3000*.h
F: include/hw/arm/ax3005*.h
F: include/hw/*/axiado*.h
+F: tests/functional/aarch64/test_axiado_scm3003.py
+F: tests/functional/aarch64/test_ax3005_evb.py
F: docs/system/arm/axiado.rst
AVR Machines
diff --git a/tests/functional/aarch64/meson.build b/tests/functional/aarch64/meson.build
index f0881bed16..3e3d918486 100644
--- a/tests/functional/aarch64/meson.build
+++ b/tests/functional/aarch64/meson.build
@@ -4,6 +4,8 @@ test_aarch64_timeouts = {
'aspeed_ast2700a1' : 600,
'aspeed_ast2700a2' : 600,
'aspeed_ast2700fc' : 600,
+ 'ax3005_evb' : 180,
+ 'axiado_scm3003' : 240,
'device_passthrough' : 720,
'imx8mm_evk' : 240,
'imx8mp_evk' : 240,
@@ -33,6 +35,8 @@ tests_aarch64_system_thorough = [
'aspeed_ast2700a1',
'aspeed_ast2700a2',
'aspeed_ast2700fc',
+ 'ax3005_evb',
+ 'axiado_scm3003',
'device_passthrough',
'hotplug_pci',
'imx8mm_evk',
diff --git a/tests/functional/aarch64/test_ax3005_evb.py b/tests/functional/aarch64/test_ax3005_evb.py
new file mode 100755
index 0000000000..5ca75b1599
--- /dev/null
+++ b/tests/functional/aarch64/test_ax3005_evb.py
@@ -0,0 +1,140 @@
+#!/usr/bin/env python3
+#
+# Functional test that boots an OpenBMC image on the Axiado AX3005 EVB
+#
+# Author: Kuan-Jui Chiu <kchiu@axiado.com>
+#
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+from qemu_test import LinuxKernelTest, Asset, wait_for_console_pattern
+
+
+class Ax3005EvbMachine(LinuxKernelTest):
+
+ ASSET_SDK_IMAGES = Asset(
+ ('https://github.com/axiado/openbmc/releases/download/v0.1.0/'
+ 'evk-ax3005-qemu.tar.gz'),
+ 'e07e89151981fb4730223dfe399a7111a0367e3c4122e21d65ef4aa8a2ba04c7')
+
+ ATF_BASE = 0x88300000
+ OPTEE_BASE = 0x88400000
+ UBOOT_BASE = 0x80000000
+ FIT_BASE = 0x80100000
+ RAMROFS_BASE = 0x80B00000
+ RAMROFS_SIZE = 0x6400000
+
+ def setUp(self):
+ super().setUp()
+
+ sdk_image_dir = 'evk-ax3005-qemu'
+
+ self.archive_extract(self.ASSET_SDK_IMAGES)
+ self.atf_path = self.scratch_file(sdk_image_dir,
+ 'trusted-firmware-a/bl31.bin')
+ self.optee_path = self.scratch_file(sdk_image_dir, 'optee/tee-raw.bin')
+ self.uboot_path = self.scratch_file(sdk_image_dir, 'u-boot.bin')
+ self.fit_path = self.scratch_file(sdk_image_dir, 'fitImage')
+ self.kernel_path = self.scratch_file(sdk_image_dir, 'Image')
+ self.dtb_path = self.scratch_file(sdk_image_dir, 'ax3005-evb-qemu.dtb')
+ self.initrd_path = self.scratch_file(
+ sdk_image_dir, 'obmc-phosphor-initramfs-evk-ax3005-qemu.cpio.xz')
+ self.rofs_path = self.scratch_file(
+ sdk_image_dir, 'obmc-phosphor-image-evk-ax3005-qemu.squashfs-xz')
+ self.disk_path = self.scratch_file(
+ sdk_image_dir, 'obmc-phosphor-image-evk-ax3005-qemu.wic.qcow2')
+
+ def test_aarch64_ax3005_evb_boot(self):
+ self.require_accelerator('tcg')
+ self.set_machine('ax3005-evb')
+
+ ramrofs_base = 0x90000000
+
+ # The SoC has nine Cadence UARTs; the console is the fourth one.
+ self.vm.set_console(console_index=3)
+ self.vm.add_args(
+ '-kernel', self.kernel_path,
+ '-dtb', self.dtb_path,
+ '-initrd', self.initrd_path,
+ '-device', 'loader,file=%s,addr=0x%x' % (self.rofs_path,
+ ramrofs_base),
+ '-drive', 'file=%s,if=sd,format=qcow2,snapshot=on' % self.disk_path,
+ '-append', 'console=ttyPS3,115200 earlycon nr_cpus=1 '
+ 'root=/dev/ram rw '
+ 'phram.phram=ramrofs,0x%x,0x%x' % (ramrofs_base,
+ self.RAMROFS_SIZE))
+
+ self.vm.launch()
+
+ self.wait_for_console_pattern('Linux version')
+ self.wait_for_console_pattern('Machine model: Axiado AX3005 EVB QEMU')
+
+ # The reservation comes from the board's modify_dtb() hook, not from
+ # the supplied DTB, which still carries the old address.
+ self.wait_for_console_pattern(
+ 'OF: reserved mem: 0x0000000090000000..0x00000000963fffff')
+
+ # phram claims the reserved window and exposes it as an MTD device.
+ wait_for_console_pattern(
+ self, 'phram: ramrofs device: 0x6400000 at 0x90000000',
+ failure_message='phram: Failed to register new device')
+
+ self.wait_for_console_pattern('Run /init as init process')
+
+ # The initramfs prints this after probing the SD card for the rwfs.
+ self.wait_for_console_pattern('blkdev: /dev/mmcblk0 sector_size: 512')
+
+ # Reaching systemd proves the initramfs mounted the squashfs out of
+ # the phram window and switch_root'ed into it.
+ self.wait_for_console_pattern('Hostname set to <evk-ax3005-qemu>')
+
+ def test_aarch64_ax3005_evb_tzboot(self):
+ self.require_accelerator('tcg')
+ self.set_machine('ax3005-evb')
+
+ # The SoC has nine Cadence UARTs; the console is the fourth one.
+ self.vm.set_console(console_index=3)
+ self.vm.add_args(
+ '-device', 'loader,file=%s,addr=0x%x' % (self.atf_path,
+ self.ATF_BASE),
+ '-device', 'loader,file=%s,addr=0x%x' % (self.optee_path,
+ self.OPTEE_BASE),
+ '-device', 'loader,file=%s,addr=0x%x' % (self.uboot_path,
+ self.UBOOT_BASE),
+ '-device', 'loader,file=%s,addr=0x%x' % (self.fit_path,
+ self.FIT_BASE),
+ '-device', 'loader,file=%s,addr=0x%x' % (self.rofs_path,
+ self.RAMROFS_BASE),
+ '-device', 'loader,cpu-num=0,addr=0x%x' % self.ATF_BASE,
+ '-device', 'loader,cpu-num=1,addr=0x%x' % self.ATF_BASE,
+ '-device', 'loader,cpu-num=2,addr=0x%x' % self.ATF_BASE,
+ '-device', 'loader,cpu-num=3,addr=0x%x' % self.ATF_BASE,
+ '-drive', 'file=%s,if=sd,format=qcow2,snapshot=on' % self.disk_path)
+
+ self.vm.launch()
+
+ self.wait_for_console_pattern('BL31: Initializing BL32')
+ self.wait_for_console_pattern('OP-TEE version:')
+ self.wait_for_console_pattern('Primary CPU switching to normal world')
+
+ self.wait_for_console_pattern('U-Boot 2026.04')
+ self.wait_for_console_pattern('Starting kernel')
+
+ self.wait_for_console_pattern('Linux version')
+ self.wait_for_console_pattern('Machine model: Axiado AX3005 EVB QEMU')
+
+ # phram claims the reserved window and exposes it as an MTD device.
+ wait_for_console_pattern(
+ self, 'phram: ramrofs device: 0x6400000 at 0x80b00000',
+ failure_message='phram: Failed to register new device')
+
+ self.wait_for_console_pattern('Run /init as init process')
+
+ # The initramfs prints this after probing the SD card for the rwfs.
+ self.wait_for_console_pattern('blkdev: /dev/mmcblk0 sector_size: 512')
+
+ # Reaching systemd proves the initramfs mounted the squashfs out of
+ # the phram window and switch_root'ed into it.
+ self.wait_for_console_pattern('Hostname set to <evk-ax3005-qemu>')
+
+if __name__ == '__main__':
+ LinuxKernelTest.main()
diff --git a/tests/functional/aarch64/test_axiado_scm3003.py b/tests/functional/aarch64/test_axiado_scm3003.py
new file mode 100755
index 0000000000..4d80931b4d
--- /dev/null
+++ b/tests/functional/aarch64/test_axiado_scm3003.py
@@ -0,0 +1,62 @@
+#!/usr/bin/env python3
+#
+# Functional test that boots an OpenBMC image on the Axiado SCM3003 EVK
+#
+# Author: Kuan-Jui Chiu <kchiu@axiado.com>
+#
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+from qemu_test import LinuxKernelTest, Asset, wait_for_console_pattern
+
+
+class AxiadoScm3003Machine(LinuxKernelTest):
+
+ ASSET_SDK_IMAGES = Asset(
+ ('https://github.com/axiado/openbmc/releases/download/v0.1.0/'
+ 'evk-axiado-qemu.tar.gz'),
+ 'a163b78ed07a43e08323395e2df63c213fbc98b8bc412083a11e94564e26548b')
+
+ def setUp(self):
+ super().setUp()
+
+ sdk_image_dir = 'evk-axiado-qemu'
+
+ self.archive_extract(self.ASSET_SDK_IMAGES)
+ self.kernel_path = self.scratch_file(sdk_image_dir, 'Image')
+ self.dtb_path = self.scratch_file(sdk_image_dir,
+ 'ax3000-scm3003-qemu.dtb')
+ self.initrd_path = self.scratch_file(
+ sdk_image_dir, 'obmc-phosphor-initramfs-evk-axiado-qemu.cpio.xz')
+ self.disk_path = self.scratch_file(
+ sdk_image_dir, 'obmc-phosphor-image-evk-axiado-qemu.wic.qcow2')
+
+ def test_aarch64_axiado_scm3003_boot(self):
+ self.require_accelerator('tcg')
+ self.set_machine('axiado-scm3003')
+
+ # The SoC has four Cadence UARTs; the console is the fourth one.
+ self.vm.set_console(console_index=3)
+ self.vm.add_args(
+ '-kernel', self.kernel_path,
+ '-dtb', self.dtb_path,
+ '-initrd', self.initrd_path,
+ '-drive', 'file=%s,if=sd,format=qcow2,snapshot=on' % self.disk_path,
+ '-append', 'console=ttyPS3,115200 earlycon nr_cpus=1 '
+ 'rootwait root=PARTLABEL=rofs-a')
+
+ self.vm.launch()
+
+ self.wait_for_console_pattern('Linux version')
+ self.wait_for_console_pattern('Machine model: Axiado AX3000-SCM3003')
+
+ self.wait_for_console_pattern('Run /init as init process')
+
+ # The initramfs prints this after probing the SD card for the rwfs.
+ self.wait_for_console_pattern('blkdev: /dev/mmcblk0 sector_size: 512')
+
+ # Reaching systemd proves the initramfs mounted the squashfs out of
+ # the phram window and switch_root'ed into it.
+ self.wait_for_console_pattern('Hostname set to <evk-axiado-qemu>')
+
+if __name__ == '__main__':
+ LinuxKernelTest.main()
--
2.34.1
^ permalink raw reply related [flat|nested] 14+ messages in thread