From: Chris Morgan <macroalpha82@gmail.com>
To: linux-rockchip@lists.infradead.org
Cc: devicetree@vger.kernel.org, shawn.lin@rock-chips.com,
linux-pm@vger.kernel.org, heiko@sntech.de, conor+dt@kernel.org,
krzk+dt@kernel.org, robh@kernel.org, sre@kernel.org,
t.schramm@manjaro.org, xsf@rock-chips.com,
Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V2 1/3] dt-bindings: power: cw2015: add cw2215, cw2217, and cw2218
Date: Fri, 20 Nov 2026 15:28:13 -0600 [thread overview]
Message-ID: <20261120212815.35663-2-macroalpha82@gmail.com> (raw)
In-Reply-To: <20261120212815.35663-1-macroalpha82@gmail.com>
From: Chris Morgan <macromorgan@hotmail.com>
Add bindings for the Cellwise cw2215/cw2217/cw2218 i2C interface
battery gauge. It is similar in function to the existing cw2015 but
with a different register layout. Each of the cw2215, cw2217 and cw2218
only really differ in the minor specs and the hardware ID they display
when queried. shunt-resistor-micro-ohms is a property in use for
multiple devices so not appending a vendor prefix to it.
Move the minItems and maxItems for the battery profile to a conditional
based on the compatible string, as the new monitors require 80 bytes of
firmware instead of 64 bytes.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
.../bindings/power/supply/cw2015_battery.yaml | 41 ++++++++++++++++---
1 file changed, 35 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
index f7bde324153d..dce7c51e4e62 100644
--- a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
+++ b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
@@ -14,12 +14,13 @@ description: |
phandle in monitored-battery. If specified the driver uses the
charge-full-design-microamp-hours property of the battery.
-allOf:
- - $ref: power-supply.yaml#
-
properties:
compatible:
- const: cellwise,cw2015
+ enum:
+ - cellwise,cw2015
+ - cellwise,cw2215
+ - cellwise,cw2217
+ - cellwise,cw2218
reg:
maxItems: 1
@@ -31,8 +32,6 @@ properties:
it is to mail two batteries to a test facility of CellWise and receive
back a test report with the binary blob.
$ref: /schemas/types.yaml#/definitions/uint8-array
- minItems: 64
- maxItems: 64
cellwise,monitor-interval-ms:
description:
@@ -43,12 +42,42 @@ properties:
minItems: 1
maxItems: 8 # Should be enough
+ shunt-resistor-micro-ohms:
+ description:
+ The value, in micro-ohms, of the shunt resistor used for sampling
+ the battery current.
+ minimum: 1000
+ maximum: 50000
+ default: 1500
+
monitored-battery: true
required:
- compatible
- reg
+allOf:
+ - $ref: power-supply.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - cellwise,cw2015
+ then:
+ properties:
+ shunt-resistor-micro-ohms: false
+
+ cellwise,battery-profile:
+ minItems: 64
+ maxItems: 64
+
+ else:
+ properties:
+ cellwise,battery-profile:
+ minItems: 80
+ maxItems: 80
+
additionalProperties: false
examples:
--
2.53.0
WARNING: multiple messages have this Message-ID (diff)
From: Chris Morgan <macroalpha82@gmail.com>
To: linux-rockchip@lists.infradead.org
Cc: devicetree@vger.kernel.org, shawn.lin@rock-chips.com,
linux-pm@vger.kernel.org, heiko@sntech.de, conor+dt@kernel.org,
krzk+dt@kernel.org, robh@kernel.org, sre@kernel.org,
t.schramm@manjaro.org, xsf@rock-chips.com,
Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V2 1/3] dt-bindings: power: cw2015: add cw2215, cw2217, and cw2218
Date: Fri, 20 Nov 2026 15:28:13 -0600 [thread overview]
Message-ID: <20261120212815.35663-2-macroalpha82@gmail.com> (raw)
In-Reply-To: <20261120212815.35663-1-macroalpha82@gmail.com>
From: Chris Morgan <macromorgan@hotmail.com>
Add bindings for the Cellwise cw2215/cw2217/cw2218 i2C interface
battery gauge. It is similar in function to the existing cw2015 but
with a different register layout. Each of the cw2215, cw2217 and cw2218
only really differ in the minor specs and the hardware ID they display
when queried. shunt-resistor-micro-ohms is a property in use for
multiple devices so not appending a vendor prefix to it.
Move the minItems and maxItems for the battery profile to a conditional
based on the compatible string, as the new monitors require 80 bytes of
firmware instead of 64 bytes.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
.../bindings/power/supply/cw2015_battery.yaml | 41 ++++++++++++++++---
1 file changed, 35 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
index f7bde324153d..dce7c51e4e62 100644
--- a/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
+++ b/Documentation/devicetree/bindings/power/supply/cw2015_battery.yaml
@@ -14,12 +14,13 @@ description: |
phandle in monitored-battery. If specified the driver uses the
charge-full-design-microamp-hours property of the battery.
-allOf:
- - $ref: power-supply.yaml#
-
properties:
compatible:
- const: cellwise,cw2015
+ enum:
+ - cellwise,cw2015
+ - cellwise,cw2215
+ - cellwise,cw2217
+ - cellwise,cw2218
reg:
maxItems: 1
@@ -31,8 +32,6 @@ properties:
it is to mail two batteries to a test facility of CellWise and receive
back a test report with the binary blob.
$ref: /schemas/types.yaml#/definitions/uint8-array
- minItems: 64
- maxItems: 64
cellwise,monitor-interval-ms:
description:
@@ -43,12 +42,42 @@ properties:
minItems: 1
maxItems: 8 # Should be enough
+ shunt-resistor-micro-ohms:
+ description:
+ The value, in micro-ohms, of the shunt resistor used for sampling
+ the battery current.
+ minimum: 1000
+ maximum: 50000
+ default: 1500
+
monitored-battery: true
required:
- compatible
- reg
+allOf:
+ - $ref: power-supply.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - cellwise,cw2015
+ then:
+ properties:
+ shunt-resistor-micro-ohms: false
+
+ cellwise,battery-profile:
+ minItems: 64
+ maxItems: 64
+
+ else:
+ properties:
+ cellwise,battery-profile:
+ minItems: 80
+ maxItems: 80
+
additionalProperties: false
examples:
--
2.53.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2026-11-20 21:28 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-20 21:28 [PATCH V2 0/3] Add Cellwise CW2217 Chris Morgan
2026-11-20 21:28 ` Chris Morgan
2026-11-20 21:28 ` Chris Morgan [this message]
2026-11-20 21:28 ` [PATCH V2 1/3] dt-bindings: power: cw2015: add cw2215, cw2217, and cw2218 Chris Morgan
2026-11-20 21:28 ` [PATCH V2 2/3] power: supply: cw2217: Add support for Cellwise cw2217 Chris Morgan
2026-11-20 21:28 ` Chris Morgan
2026-11-20 21:42 ` sashiko-bot
2026-11-20 21:28 ` [PATCH V2 3/3] arm64: dts: rockchip: Add Battery Gauge to Anbernic Vita-Pro Chris Morgan
2026-11-20 21:28 ` Chris Morgan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261120212815.35663-2-macroalpha82@gmail.com \
--to=macroalpha82@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=heiko@sntech.de \
--cc=krzk+dt@kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=macromorgan@hotmail.com \
--cc=robh@kernel.org \
--cc=shawn.lin@rock-chips.com \
--cc=sre@kernel.org \
--cc=t.schramm@manjaro.org \
--cc=xsf@rock-chips.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.