* [PATCH v4] wifi: wilc1000: add back-off algorithm to balance tx queue packets
@ 2023-09-15 18:00 Prasurjya.Rohansaikia
2023-09-15 19:20 ` Ajay.Kathat
2023-09-21 6:30 ` Kalle Valo
0 siblings, 2 replies; 3+ messages in thread
From: Prasurjya.Rohansaikia @ 2023-09-15 18:00 UTC (permalink / raw)
To: linux-wireless; +Cc: Ajay.Kathat, claudiu.beznea
From: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Add an algorithm to backoff the Tx Task when low memory scenario is
triggered at firmware. During high data transfer from host, the firmware
runs out of VMM memory, which is used to hold the frames from the host.
So, adding the flow control delays the transmit from host side when
there is not enough space to accommodate frames in firmware side.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
---
v3 -> v4: As per review comments, replaced
schedule_timeout_interruptible() by msleep_interruptible().
v2 -> v3: Replaced schedule_timeout() by
schedule_timeout_interruptible().
v1 -> v2: Removed the unused `timeout` variable.
---
.../net/wireless/microchip/wilc1000/netdev.c | 20 +++++++++++++++----
.../net/wireless/microchip/wilc1000/netdev.h | 2 ++
2 files changed, 18 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.c b/drivers/net/wireless/microchip/wilc1000/netdev.c
index e9f59de31b0b..91d71e0f7ef2 100644
--- a/drivers/net/wireless/microchip/wilc1000/netdev.c
+++ b/drivers/net/wireless/microchip/wilc1000/netdev.c
@@ -148,8 +148,8 @@ static int wilc_txq_task(void *vp)
complete(&wl->txq_thread_started);
while (1) {
- wait_for_completion(&wl->txq_event);
-
+ if (wait_for_completion_interruptible(&wl->txq_event))
+ continue;
if (wl->close) {
complete(&wl->txq_thread_started);
@@ -166,12 +166,24 @@ static int wilc_txq_task(void *vp)
srcu_idx = srcu_read_lock(&wl->srcu);
list_for_each_entry_rcu(ifc, &wl->vif_list,
list) {
- if (ifc->mac_opened && ifc->ndev)
+ if (ifc->mac_opened &&
+ netif_queue_stopped(ifc->ndev))
netif_wake_queue(ifc->ndev);
}
srcu_read_unlock(&wl->srcu, srcu_idx);
}
- } while (ret == WILC_VMM_ENTRY_FULL_RETRY && !wl->close);
+ if (ret != WILC_VMM_ENTRY_FULL_RETRY)
+ break;
+ /* Back off TX task from sending packets for some time.
+ * msleep_interruptible will allow RX task to run and
+ * free buffers. TX task will be in TASK_INTERRUPTIBLE
+ * state which will put the thread back to CPU running
+ * queue when it's signaled even if the timeout isn't
+ * elapsed. This gives faster chance for reserved SK
+ * buffers to be free.
+ */
+ msleep_interruptible(TX_BACKOFF_WEIGHT_MS);
+ } while (!wl->close);
}
return 0;
}
diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.h b/drivers/net/wireless/microchip/wilc1000/netdev.h
index bb1a315a7b7e..aafe3dc44ac6 100644
--- a/drivers/net/wireless/microchip/wilc1000/netdev.h
+++ b/drivers/net/wireless/microchip/wilc1000/netdev.h
@@ -27,6 +27,8 @@
#define TCP_ACK_FILTER_LINK_SPEED_THRESH 54
#define DEFAULT_LINK_SPEED 72
+#define TX_BACKOFF_WEIGHT_MS 1
+
struct wilc_wfi_stats {
unsigned long rx_packets;
unsigned long tx_packets;
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH v4] wifi: wilc1000: add back-off algorithm to balance tx queue packets
2023-09-15 18:00 [PATCH v4] wifi: wilc1000: add back-off algorithm to balance tx queue packets Prasurjya.Rohansaikia
@ 2023-09-15 19:20 ` Ajay.Kathat
2023-09-21 6:30 ` Kalle Valo
1 sibling, 0 replies; 3+ messages in thread
From: Ajay.Kathat @ 2023-09-15 19:20 UTC (permalink / raw)
To: Prasurjya.Rohansaikia, linux-wireless; +Cc: claudiu.beznea
On 9/15/23 11:00, Prasurjya Rohan saikia - I73664 wrote:
> From: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
>
> Add an algorithm to backoff the Tx Task when low memory scenario is
> triggered at firmware. During high data transfer from host, the firmware
> runs out of VMM memory, which is used to hold the frames from the host.
> So, adding the flow control delays the transmit from host side when
> there is not enough space to accommodate frames in firmware side.
>
> Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
> ---
> v3 -> v4: As per review comments, replaced
> schedule_timeout_interruptible() by msleep_interruptible().
>
> v2 -> v3: Replaced schedule_timeout() by
> schedule_timeout_interruptible().
>
> v1 -> v2: Removed the unused `timeout` variable.
> ---
> .../net/wireless/microchip/wilc1000/netdev.c | 20 +++++++++++++++----
> .../net/wireless/microchip/wilc1000/netdev.h | 2 ++
> 2 files changed, 18 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.c b/drivers/net/wireless/microchip/wilc1000/netdev.c
> index e9f59de31b0b..91d71e0f7ef2 100644
> --- a/drivers/net/wireless/microchip/wilc1000/netdev.c
> +++ b/drivers/net/wireless/microchip/wilc1000/netdev.c
> @@ -148,8 +148,8 @@ static int wilc_txq_task(void *vp)
>
> complete(&wl->txq_thread_started);
> while (1) {
> - wait_for_completion(&wl->txq_event);
> -
> + if (wait_for_completion_interruptible(&wl->txq_event))
> + continue;
> if (wl->close) {
> complete(&wl->txq_thread_started);
>
> @@ -166,12 +166,24 @@ static int wilc_txq_task(void *vp)
> srcu_idx = srcu_read_lock(&wl->srcu);
> list_for_each_entry_rcu(ifc, &wl->vif_list,
> list) {
> - if (ifc->mac_opened && ifc->ndev)
> + if (ifc->mac_opened &&
> + netif_queue_stopped(ifc->ndev))
> netif_wake_queue(ifc->ndev);
> }
> srcu_read_unlock(&wl->srcu, srcu_idx);
> }
> - } while (ret == WILC_VMM_ENTRY_FULL_RETRY && !wl->close);
> + if (ret != WILC_VMM_ENTRY_FULL_RETRY)
> + break;
> + /* Back off TX task from sending packets for some time.
> + * msleep_interruptible will allow RX task to run and
> + * free buffers. TX task will be in TASK_INTERRUPTIBLE
> + * state which will put the thread back to CPU running
> + * queue when it's signaled even if the timeout isn't
> + * elapsed. This gives faster chance for reserved SK
> + * buffers to be free.
> + */
> + msleep_interruptible(TX_BACKOFF_WEIGHT_MS);
> + } while (!wl->close);
> }
> return 0;
> }
> diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.h b/drivers/net/wireless/microchip/wilc1000/netdev.h
> index bb1a315a7b7e..aafe3dc44ac6 100644
> --- a/drivers/net/wireless/microchip/wilc1000/netdev.h
> +++ b/drivers/net/wireless/microchip/wilc1000/netdev.h
> @@ -27,6 +27,8 @@
> #define TCP_ACK_FILTER_LINK_SPEED_THRESH 54
> #define DEFAULT_LINK_SPEED 72
>
> +#define TX_BACKOFF_WEIGHT_MS 1
> +
> struct wilc_wfi_stats {
> unsigned long rx_packets;
> unsigned long tx_packets;
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH v4] wifi: wilc1000: add back-off algorithm to balance tx queue packets
2023-09-15 18:00 [PATCH v4] wifi: wilc1000: add back-off algorithm to balance tx queue packets Prasurjya.Rohansaikia
2023-09-15 19:20 ` Ajay.Kathat
@ 2023-09-21 6:30 ` Kalle Valo
1 sibling, 0 replies; 3+ messages in thread
From: Kalle Valo @ 2023-09-21 6:30 UTC (permalink / raw)
To: Prasurjya.Rohansaikia; +Cc: linux-wireless, Ajay.Kathat, claudiu.beznea
<Prasurjya.Rohansaikia@microchip.com> wrote:
> From: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
>
> Add an algorithm to backoff the Tx Task when low memory scenario is
> triggered at firmware. During high data transfer from host, the firmware
> runs out of VMM memory, which is used to hold the frames from the host.
> So, adding the flow control delays the transmit from host side when
> there is not enough space to accommodate frames in firmware side.
>
> Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
> Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Patch applied to wireless-next.git, thanks.
a08bb28f6eb6 wifi: wilc1000: add back-off algorithm to balance tx queue packets
--
https://patchwork.kernel.org/project/linux-wireless/patch/20230915175946.4361-1-prasurjya.rohansaikia@microchip.com/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2023-09-21 19:29 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2023-09-15 18:00 [PATCH v4] wifi: wilc1000: add back-off algorithm to balance tx queue packets Prasurjya.Rohansaikia
2023-09-15 19:20 ` Ajay.Kathat
2023-09-21 6:30 ` Kalle Valo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.