Re: [PATCH v2 12/13] ARM: dts: imx: add i.MXRT1050-EVK support

From: Jesse Taube <mr.bossman075@gmail.com>
To: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Shawn Guo <shawnguo@kernel.org>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Sascha Hauer <kernel@pengutronix.de>,
	Ulf Hansson <ulf.hansson@linaro.org>,
	Dong Aisheng <aisheng.dong@nxp.com>,
	Stefan Agner <stefan@agner.ch>,
	Linus Walleij <linus.walleij@linaro.org>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
	soc@kernel.org, Russell King - ARM Linux <linux@armlinux.org.uk>,
	Abel Vesa <abel.vesa@nxp.com>,
	Adrian Hunter <adrian.hunter@intel.com>,
	Jiri Slaby <jirislaby@kernel.org>,
	Giulio Benetti <giulio.benetti@benettiengineering.com>,
	Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>,
	linux-clk <linux-clk@vger.kernel.org>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
	<devicetree@vger.kernel.org>,
	"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE" 
	<linux-arm-kernel@lists.infradead.org>,
	linux-kernel <linux-kernel@vger.kernel.org>,
	linux-mmc <linux-mmc@vger.kernel.org>,
	"open list:GPIO SUBSYSTEM" <linux-gpio@vger.kernel.org>,
	linux-serial@vger.kernel.org
Subject: Re: [PATCH v2 12/13] ARM: dts: imx: add i.MXRT1050-EVK support
Date: Tue, 2 Nov 2021 22:19:08 -0400	[thread overview]
Message-ID: <2fbe7ced-60a7-2fd2-6032-e4ddae21b565@gmail.com> (raw)
In-Reply-To: <e2f81ad7-9c58-3e39-fbb0-5ef3132bba7d@gmail.com>


On 11/2/21 19:54, Jesse Taube wrote:
> 
> 
> On 11/2/21 19:42, Fabio Estevam wrote:
>> On Tue, Nov 2, 2021 at 7:57 PM Jesse Taube <mr.bossman075@gmail.com> wrote:
>>
>>> +/ {
>>> +       model = "NXP IMXRT1050-evk board";
>>> +       compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
>>> +
>>> +       chosen {
>>> +               bootargs = "root=/dev/ram";
>>
>> No need to pass bootargs here.
>>
>>> +               stdout-path = &lpuart1;
>>> +       };
>>> +
>>> +       aliases {
>>> +               gpio0 = &gpio1;
>>> +               gpio1 = &gpio2;
>>> +               gpio2 = &gpio3;
>>> +               gpio3 = &gpio4;
>>> +               gpio4 = &gpio5;
>>> +               mmc0 = &usdhc1;
>>> +               serial0 = &lpuart1;
>>> +       };
>>> +
>>> +       memory@0 {
>>
>> memory@80000000
>>
>> Building with W=1 should give a dtc warning due to the unit address
>> and reg mismatch.
> Oh that makes sense.
> I guess I'm going to have to figure out how to get warnings to work as I
> couldn't last time I tried.
Oh i got it to work I did something dumb...
I didn't give a warning for this i still changed it of course.
>>
>>> +               device_type = "memory";
>>> +               reg = <0x80000000 0x2000000>;
>>> +       };
>>> +
>>
>> Unneeded blank line.
>>> +
>>> +&iomuxc {
>>> +       pinctrl-names = "default";
>>> +
>>> +       imxrt1050-evk {
>>
>> No need for this imxrt1050-evk container.
> I was wondering if that was needed, u-boot has it, good to know.
>>
>>> +               pinctrl_lpuart1: lpuart1grp {
>>> +                       fsl,pins = <
>>> +                               MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD
>>> +                                       0xf1
>>
>> Put it on a single line. It helps readability. Same applies globally.
>>> +&usdhc1 {
>>> +       pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
>>> +       pinctrl-0 = <&pinctrl_usdhc0>;
>>> +       pinctrl-1 = <&pinctrl_usdhc0>;
>>> +       pinctrl-2 = <&pinctrl_usdhc0>;
>>> +       pinctrl-3 = <&pinctrl_usdhc0>;
>>> +       status = "okay";
>>> +
>>> +       cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
>>
>> Make 'status' to be the last property. Remove the blank line.
>>
>>> +               edma1: dma-controller@400e8000 {
>>> +                       #dma-cells = <2>;
>>> +                       compatible = "fsl,imx7ulp-edma";
>>> +                       reg = <0x400e8000 0x4000>,
>>> +                               <0x400ec000 0x4000>;
>>> +                       dma-channels = <32>;
>>> +                       interrupts = <0>,
>>> +                               <1>,
>>> +                               <2>,
>>> +                               <3>,
>>> +                               <4>,
>>> +                               <5>,
>>> +                               <6>,
>>> +                               <7>,
>>> +                               <8>,
>>> +                               <9>,
>>> +                               <10>,
>>> +                               <11>,
>>> +                               <12>,
>>> +                               <13>,
>>> +                               <14>,
>>> +                               <15>,
>>> +                               <16>;
>>
>> Please group more elements into the same line.
>>
>> Putting one entry per line makes it extremely long.
>>
>>> +               gpio5: gpio@400c0000 {
>>> +                       compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio";
>>> +                       reg = <0x400c0000 0x4000>;
>>> +                       interrupts = <88>,
>>> +                               <89>;
>>
>> Put the interrupts into a single line.
>>
> Ah all these make sense, will fix, sry about that.
>