* [PATCH 0/3] add support for Firefly-RK3288 and Rayeager PX2 boards
@ 2015-01-15 2:40 ` FUKAUMI Naoki
0 siblings, 0 replies; 16+ messages in thread
From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw)
To: linux-arm-kernel
This series adds support for following Rockchip SoC based boards.
- Firefly, Firefly-RK3288 (both beta and mass production version)
- ChipSPARK, Rayeager PX2
FUKAUMI Naoki (3):
dt-bindings: add vendor prefix and root compatible property for
Rockchip boards
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
Documentation/devicetree/bindings/arm/rockchip.txt | 8 +
.../devicetree/bindings/vendor-prefixes.txt | 2 +
arch/arm/boot/dts/Makefile | 5 +-
arch/arm/boot/dts/rk3066a-rayeager.dts | 457 +++++++++++++++++++
arch/arm/boot/dts/rk3288-firefly-beta.dts | 70 +++
arch/arm/boot/dts/rk3288-firefly.dts | 70 +++
arch/arm/boot/dts/rk3288-firefly.dtsi | 498 +++++++++++++++++++++
7 files changed, 1109 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rk3066a-rayeager.dts
create mode 100644 arch/arm/boot/dts/rk3288-firefly-beta.dts
create mode 100644 arch/arm/boot/dts/rk3288-firefly.dts
create mode 100644 arch/arm/boot/dts/rk3288-firefly.dtsi
--
2.2.2
^ permalink raw reply [flat|nested] 16+ messages in thread* [PATCH 0/3] add support for Firefly-RK3288 and Rayeager PX2 boards @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Cc: FUKAUMI Naoki This series adds support for following Rockchip SoC based boards. - Firefly, Firefly-RK3288 (both beta and mass production version) - ChipSPARK, Rayeager PX2 FUKAUMI Naoki (3): dt-bindings: add vendor prefix and root compatible property for Rockchip boards ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board Documentation/devicetree/bindings/arm/rockchip.txt | 8 + .../devicetree/bindings/vendor-prefixes.txt | 2 + arch/arm/boot/dts/Makefile | 5 +- arch/arm/boot/dts/rk3066a-rayeager.dts | 457 +++++++++++++++++++ arch/arm/boot/dts/rk3288-firefly-beta.dts | 70 +++ arch/arm/boot/dts/rk3288-firefly.dts | 70 +++ arch/arm/boot/dts/rk3288-firefly.dtsi | 498 +++++++++++++++++++++ 7 files changed, 1109 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/rk3066a-rayeager.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly-beta.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly.dtsi -- 2.2.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH 1/3] dt-bindings: add vendor prefix and root compatible property for Rockchip boards @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: linux-arm-kernel this adds vendor prefix and root compatible property for following boards - Firefly, Firefly-RK3288 board - ChipSPARK, Rayeager PX2 board PX2 SoC is fully compatible with RK3066. Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> --- Documentation/devicetree/bindings/arm/rockchip.txt | 8 ++++++++ Documentation/devicetree/bindings/vendor-prefixes.txt | 2 ++ 2 files changed, 10 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index eaa3d1a..7cc1cecd 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -9,6 +9,14 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; +- ChipSPARK Rayeager PX2 board: + Required root node properties: + - compatible = "chipspark,rayeager-px2", "rockchip,rk3066a"; + - Radxa Rock board: Required root node properties: - compatible = "radxa,rock", "rockchip,rk3188"; + +- Firefly Firefly-RK3288 board: + Required root node properties: + - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 5d2251a..0d37f5f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -32,6 +32,7 @@ capella Capella Microsystems, Inc cavium Cavium, Inc. cdns Cadence Design Systems Inc. chipidea Chipidea, Inc +chipspark ChipSPARK chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. cirrus Cirrus Logic, Inc. @@ -62,6 +63,7 @@ everest Everest Semiconductor Co. Ltd. everspin Everspin Technologies, Inc. excito Excito fcs Fairchild Semiconductor +firefly Firefly fsl Freescale Semiconductor GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. -- 2.2.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 1/3] dt-bindings: add vendor prefix and root compatible property for Rockchip boards @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Cc: FUKAUMI Naoki this adds vendor prefix and root compatible property for following boards - Firefly, Firefly-RK3288 board - ChipSPARK, Rayeager PX2 board PX2 SoC is fully compatible with RK3066. Signed-off-by: FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> --- Documentation/devicetree/bindings/arm/rockchip.txt | 8 ++++++++ Documentation/devicetree/bindings/vendor-prefixes.txt | 2 ++ 2 files changed, 10 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index eaa3d1a..7cc1cecd 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -9,6 +9,14 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; +- ChipSPARK Rayeager PX2 board: + Required root node properties: + - compatible = "chipspark,rayeager-px2", "rockchip,rk3066a"; + - Radxa Rock board: Required root node properties: - compatible = "radxa,rock", "rockchip,rk3188"; + +- Firefly Firefly-RK3288 board: + Required root node properties: + - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 5d2251a..0d37f5f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -32,6 +32,7 @@ capella Capella Microsystems, Inc cavium Cavium, Inc. cdns Cadence Design Systems Inc. chipidea Chipidea, Inc +chipspark ChipSPARK chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. cirrus Cirrus Logic, Inc. @@ -62,6 +63,7 @@ everest Everest Semiconductor Co. Ltd. everspin Everspin Technologies, Inc. excito Excito fcs Fairchild Semiconductor +firefly Firefly fsl Freescale Semiconductor GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. -- 2.2.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 1/3] dt-bindings: add vendor prefix and root compatible property for Rockchip boards @ 2015-01-15 14:12 ` Heiko Stübner 0 siblings, 0 replies; 16+ messages in thread From: Heiko Stübner @ 2015-01-15 14:12 UTC (permalink / raw) To: linux-arm-kernel Am Donnerstag, 15. Januar 2015, 11:40:57 schrieb FUKAUMI Naoki: > this adds vendor prefix and root compatible property for following boards > > - Firefly, Firefly-RK3288 board > - ChipSPARK, Rayeager PX2 board > > PX2 SoC is fully compatible with RK3066. > > Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> > --- > Documentation/devicetree/bindings/arm/rockchip.txt | 8 ++++++++ > Documentation/devicetree/bindings/vendor-prefixes.txt | 2 ++ > 2 files changed, 10 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt > b/Documentation/devicetree/bindings/arm/rockchip.txt index > eaa3d1a..7cc1cecd 100644 > --- a/Documentation/devicetree/bindings/arm/rockchip.txt > +++ b/Documentation/devicetree/bindings/arm/rockchip.txt > @@ -9,6 +9,14 @@ Rockchip platforms device tree bindings > Required root node properties: > - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; > > +- ChipSPARK Rayeager PX2 board: > + Required root node properties: > + - compatible = "chipspark,rayeager-px2", "rockchip,rk3066a"; > + > - Radxa Rock board: > Required root node properties: > - compatible = "radxa,rock", "rockchip,rk3188"; > + > +- Firefly Firefly-RK3288 board: > + Required root node properties: > + - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; you're adding two boards (beta and retail) and as they are not compatible to each other (see gpio differences), they should also have their own compatible properties, so something like: - Firefly Firefly-RK3288 board: Required root node properties: - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; and this differentiation should of course also happen in the dts files themself. Heiko ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 1/3] dt-bindings: add vendor prefix and root compatible property for Rockchip boards @ 2015-01-15 14:12 ` Heiko Stübner 0 siblings, 0 replies; 16+ messages in thread From: Heiko Stübner @ 2015-01-15 14:12 UTC (permalink / raw) To: FUKAUMI Naoki Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Am Donnerstag, 15. Januar 2015, 11:40:57 schrieb FUKAUMI Naoki: > this adds vendor prefix and root compatible property for following boards > > - Firefly, Firefly-RK3288 board > - ChipSPARK, Rayeager PX2 board > > PX2 SoC is fully compatible with RK3066. > > Signed-off-by: FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > --- > Documentation/devicetree/bindings/arm/rockchip.txt | 8 ++++++++ > Documentation/devicetree/bindings/vendor-prefixes.txt | 2 ++ > 2 files changed, 10 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt > b/Documentation/devicetree/bindings/arm/rockchip.txt index > eaa3d1a..7cc1cecd 100644 > --- a/Documentation/devicetree/bindings/arm/rockchip.txt > +++ b/Documentation/devicetree/bindings/arm/rockchip.txt > @@ -9,6 +9,14 @@ Rockchip platforms device tree bindings > Required root node properties: > - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; > > +- ChipSPARK Rayeager PX2 board: > + Required root node properties: > + - compatible = "chipspark,rayeager-px2", "rockchip,rk3066a"; > + > - Radxa Rock board: > Required root node properties: > - compatible = "radxa,rock", "rockchip,rk3188"; > + > +- Firefly Firefly-RK3288 board: > + Required root node properties: > + - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; you're adding two boards (beta and retail) and as they are not compatible to each other (see gpio differences), they should also have their own compatible properties, so something like: - Firefly Firefly-RK3288 board: Required root node properties: - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; and this differentiation should of course also happen in the dts files themself. Heiko -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH 2/3] ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> --- arch/arm/boot/dts/Makefile | 4 +- arch/arm/boot/dts/rk3288-firefly-beta.dts | 70 +++++ arch/arm/boot/dts/rk3288-firefly.dts | 70 +++++ arch/arm/boot/dts/rk3288-firefly.dtsi | 498 ++++++++++++++++++++++++++++++ 4 files changed, 641 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/rk3288-firefly-beta.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index cb686e6..fb03a2b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -447,7 +447,9 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3066a-marsboard.dtb \ rk3188-radxarock.dtb \ rk3288-evb-act8846.dtb \ - rk3288-evb-rk808.dtb + rk3288-evb-rk808.dtb \ + rk3288-firefly-beta.dtb \ + rk3288-firefly.dtb dtb-$(CONFIG_ARCH_S3C24XX) += \ s3c2416-smdk2416.dtb dtb-$(CONFIG_ARCH_S3C64XX) += \ diff --git a/arch/arm/boot/dts/rk3288-firefly-beta.dts b/arch/arm/boot/dts/rk3288-firefly-beta.dts new file mode 100644 index 0000000..d640569 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-firefly-beta.dts @@ -0,0 +1,70 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-firefly.dtsi" + +/ { + model = "Firefly-RK3288 Beta"; +}; + +&ir { + gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; +}; + +&pwm0 { + status = "okay"; +}; + +&pinctrl { + ir { + ir_int: ir-int { + rockchip,pins = <7 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + act8846 { + pmic_vsel: pmic-vsel { + rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>; + }; + }; +}; diff --git a/arch/arm/boot/dts/rk3288-firefly.dts b/arch/arm/boot/dts/rk3288-firefly.dts new file mode 100644 index 0000000..0bdc37c --- /dev/null +++ b/arch/arm/boot/dts/rk3288-firefly.dts @@ -0,0 +1,70 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-firefly.dtsi" + +/ { + model = "Firefly-RK3288"; +}; + +&ir { + gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; +}; + +&pwm1 { + status = "okay"; +}; + +&pinctrl { + ir { + ir_int: ir-int { + rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + act8846 { + pmic_vsel: pmic-vsel { + rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>; + }; + }; +}; diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rk3288-firefly.dtsi new file mode 100644 index 0000000..5996778 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi @@ -0,0 +1,498 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "rk3288.dtsi" + +/ { + compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; + + memory { + reg = <0 0x80000000>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + #clock-cells = <0>; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button at 0 { + gpio-key,wakeup = <1>; + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + label = "GPIO Power"; + linux,code = <116>; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_key>; + }; + }; + + leds { + compatible = "gpio-leds"; + + work { + gpios = <&gpio8 1 GPIO_ACTIVE_LOW>; + label = "firefly:blue:user"; + linux,default-trigger = "rc-feedback"; + pinctrl-names = "default"; + pinctrl-0 = <&work_led>; + }; + + power { + gpios = <&gpio8 2 GPIO_ACTIVE_LOW>; + label = "firefly:green:power"; + linux,default-trigger = "default-on"; + pinctrl-names = "default"; + pinctrl-0 = <&power_led>; + }; + }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwr>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + vin-supply = <&vcc_io>; + }; + + vcc_flash: flash-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_flash"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_io>; + }; + + vcc_5v: usb-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vcc_host_5v: usb-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host_vbus_drv>; + regulator-name = "vcc_host_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vcc_5v>; + }; + + vcc_otg_5v: usb-otg-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&otg_vbus_drv>; + regulator-name = "vcc_otg_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vcc_5v>; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; + status = "okay"; + vmmc-supply = <&vcc_sd>; + vqmmc-supply = <&vccio_sd>; +}; + +&sdio0 { + broken-cd; + bus-width = <4>; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>; + status = "okay"; + vmmc-supply = <&vcc_18>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>; + status = "okay"; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vcc_flash>; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc_18>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>; + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_clk>, <&spi2_cs0>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <0>; + /* status = "okay"; */ +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>; + phy_regulator = "vcc_lan"; + phy-mode = "rgmii"; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&usb_host1 { + pinctrl-names = "default"; + pinctrl-0 = <&usbhub_rst>; + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + vdd_cpu: syr827 at 40 { + compatible = "silergy,syr827"; + fcs,suspend-voltage-selector = <1>; + reg = <0x40>; + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vdd_gpu: syr828 at 41 { + compatible = "silergy,syr828"; + fcs,suspend-voltage-selector = <1>; + reg = <0x41>; + regulator-name = "vdd_gpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + vin-supply = <&vcc_sys>; + }; + + hym8563: hym8563 at 51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + interrupt-parent = <&gpio7>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&rtc_int>; + #clock-cells = <0>; + clock-output-names = "xin32k"; + }; + + act8846: act8846 at 5a { + compatible = "active-semi,act8846"; + reg = <0x5a>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_vsel>, <&pwr_hold>; + system-power-controller; + + regulators { + vcc_ddr: REG1 { + regulator-name = "vcc_ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vcc_io: REG2 { + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_log: REG3 { + regulator-name = "vdd_log"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vcc_20: REG4 { + regulator-name = "vcc_20"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + vccio_sd: REG5 { + regulator-name = "vccio_sd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd10_lcd: REG6 { + regulator-name = "vdd10_lcd"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vcca_18: REG7 { + regulator-name = "vcca_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcca_33: REG8 { + regulator-name = "vcca_33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_lan: REG9 { + regulator-name = "vcc_lan"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_10: REG10 { + regulator-name = "vdd_10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcc_18: REG11 { + regulator-name = "vcc_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcc18_lcd: REG12 { + regulator-name = "vcc18_lcd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + pcfg_output_low: pcfg-output-low { + output-low; + }; + + keys { + pwr_key: pwr-key { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + leds { + work_led: work-led { + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + power_led: power-led { + rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + gmac { + phy_rst: phy-rst { + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>; + }; + + phy_pmeb: phy-pmeb { + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + phy_int: phy-int { + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + }; + + usb_host { + host_vbus_drv: host-vbus-drv { + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + usbhub_rst: usbhub-rst { + rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + usb_otg { + otg_vbus_drv: otg-vbus-drv { + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hym8563 { + rtc_int: rtc-int { + rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + act8846 { + pwr_hold: pwr-hold { + rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; +}; -- 2.2.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 2/3] ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Cc: FUKAUMI Naoki Signed-off-by: FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> --- arch/arm/boot/dts/Makefile | 4 +- arch/arm/boot/dts/rk3288-firefly-beta.dts | 70 +++++ arch/arm/boot/dts/rk3288-firefly.dts | 70 +++++ arch/arm/boot/dts/rk3288-firefly.dtsi | 498 ++++++++++++++++++++++++++++++ 4 files changed, 641 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/rk3288-firefly-beta.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly.dts create mode 100644 arch/arm/boot/dts/rk3288-firefly.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index cb686e6..fb03a2b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -447,7 +447,9 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3066a-marsboard.dtb \ rk3188-radxarock.dtb \ rk3288-evb-act8846.dtb \ - rk3288-evb-rk808.dtb + rk3288-evb-rk808.dtb \ + rk3288-firefly-beta.dtb \ + rk3288-firefly.dtb dtb-$(CONFIG_ARCH_S3C24XX) += \ s3c2416-smdk2416.dtb dtb-$(CONFIG_ARCH_S3C64XX) += \ diff --git a/arch/arm/boot/dts/rk3288-firefly-beta.dts b/arch/arm/boot/dts/rk3288-firefly-beta.dts new file mode 100644 index 0000000..d640569 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-firefly-beta.dts @@ -0,0 +1,70 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-firefly.dtsi" + +/ { + model = "Firefly-RK3288 Beta"; +}; + +&ir { + gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; +}; + +&pwm0 { + status = "okay"; +}; + +&pinctrl { + ir { + ir_int: ir-int { + rockchip,pins = <7 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + act8846 { + pmic_vsel: pmic-vsel { + rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>; + }; + }; +}; diff --git a/arch/arm/boot/dts/rk3288-firefly.dts b/arch/arm/boot/dts/rk3288-firefly.dts new file mode 100644 index 0000000..0bdc37c --- /dev/null +++ b/arch/arm/boot/dts/rk3288-firefly.dts @@ -0,0 +1,70 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3288-firefly.dtsi" + +/ { + model = "Firefly-RK3288"; +}; + +&ir { + gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; +}; + +&pwm1 { + status = "okay"; +}; + +&pinctrl { + ir { + ir_int: ir-int { + rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + act8846 { + pmic_vsel: pmic-vsel { + rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>; + }; + }; +}; diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rk3288-firefly.dtsi new file mode 100644 index 0000000..5996778 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi @@ -0,0 +1,498 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "rk3288.dtsi" + +/ { + compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; + + memory { + reg = <0 0x80000000>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + #clock-cells = <0>; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@0 { + gpio-key,wakeup = <1>; + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + label = "GPIO Power"; + linux,code = <116>; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_key>; + }; + }; + + leds { + compatible = "gpio-leds"; + + work { + gpios = <&gpio8 1 GPIO_ACTIVE_LOW>; + label = "firefly:blue:user"; + linux,default-trigger = "rc-feedback"; + pinctrl-names = "default"; + pinctrl-0 = <&work_led>; + }; + + power { + gpios = <&gpio8 2 GPIO_ACTIVE_LOW>; + label = "firefly:green:power"; + linux,default-trigger = "default-on"; + pinctrl-names = "default"; + pinctrl-0 = <&power_led>; + }; + }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwr>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + vin-supply = <&vcc_io>; + }; + + vcc_flash: flash-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_flash"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_io>; + }; + + vcc_5v: usb-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vcc_host_5v: usb-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host_vbus_drv>; + regulator-name = "vcc_host_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vcc_5v>; + }; + + vcc_otg_5v: usb-otg-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&otg_vbus_drv>; + regulator-name = "vcc_otg_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vcc_5v>; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; + status = "okay"; + vmmc-supply = <&vcc_sd>; + vqmmc-supply = <&vccio_sd>; +}; + +&sdio0 { + broken-cd; + bus-width = <4>; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>; + status = "okay"; + vmmc-supply = <&vcc_18>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>; + status = "okay"; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vcc_flash>; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc_18>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>; + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_clk>, <&spi2_cs0>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <0>; + /* status = "okay"; */ +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>; + phy_regulator = "vcc_lan"; + phy-mode = "rgmii"; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&usb_host1 { + pinctrl-names = "default"; + pinctrl-0 = <&usbhub_rst>; + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + vdd_cpu: syr827@40 { + compatible = "silergy,syr827"; + fcs,suspend-voltage-selector = <1>; + reg = <0x40>; + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vdd_gpu: syr828@41 { + compatible = "silergy,syr828"; + fcs,suspend-voltage-selector = <1>; + reg = <0x41>; + regulator-name = "vdd_gpu"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + vin-supply = <&vcc_sys>; + }; + + hym8563: hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + interrupt-parent = <&gpio7>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&rtc_int>; + #clock-cells = <0>; + clock-output-names = "xin32k"; + }; + + act8846: act8846@5a { + compatible = "active-semi,act8846"; + reg = <0x5a>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_vsel>, <&pwr_hold>; + system-power-controller; + + regulators { + vcc_ddr: REG1 { + regulator-name = "vcc_ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vcc_io: REG2 { + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_log: REG3 { + regulator-name = "vdd_log"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vcc_20: REG4 { + regulator-name = "vcc_20"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + vccio_sd: REG5 { + regulator-name = "vccio_sd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd10_lcd: REG6 { + regulator-name = "vdd10_lcd"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vcca_18: REG7 { + regulator-name = "vcca_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcca_33: REG8 { + regulator-name = "vcca_33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_lan: REG9 { + regulator-name = "vcc_lan"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_10: REG10 { + regulator-name = "vdd_10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + vcc_18: REG11 { + regulator-name = "vcc_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcc18_lcd: REG12 { + regulator-name = "vcc18_lcd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + pcfg_output_low: pcfg-output-low { + output-low; + }; + + keys { + pwr_key: pwr-key { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + leds { + work_led: work-led { + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + power_led: power-led { + rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + gmac { + phy_rst: phy-rst { + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>; + }; + + phy_pmeb: phy-pmeb { + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + phy_int: phy-int { + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + }; + + usb_host { + host_vbus_drv: host-vbus-drv { + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + usbhub_rst: usbhub-rst { + rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + usb_otg { + otg_vbus_drv: otg-vbus-drv { + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hym8563 { + rtc_int: rtc-int { + rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + act8846 { + pwr_hold: pwr-hold { + rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; +}; -- 2.2.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 2/3] ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards @ 2015-01-15 14:19 ` Heiko Stübner 0 siblings, 0 replies; 16+ messages in thread From: Heiko Stübner @ 2015-01-15 14:19 UTC (permalink / raw) To: linux-arm-kernel Please add at least a small real commit message Am Donnerstag, 15. Januar 2015, 11:40:58 schrieb FUKAUMI Naoki: > Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> > --- > arch/arm/boot/dts/Makefile | 4 +- > arch/arm/boot/dts/rk3288-firefly-beta.dts | 70 +++++ > arch/arm/boot/dts/rk3288-firefly.dts | 70 +++++ > arch/arm/boot/dts/rk3288-firefly.dtsi | 498 > ++++++++++++++++++++++++++++++ 4 files changed, 641 insertions(+), 1 > deletion(-) > create mode 100644 arch/arm/boot/dts/rk3288-firefly-beta.dts > create mode 100644 arch/arm/boot/dts/rk3288-firefly.dts > create mode 100644 arch/arm/boot/dts/rk3288-firefly.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index cb686e6..fb03a2b 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -447,7 +447,9 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ > rk3066a-marsboard.dtb \ > rk3188-radxarock.dtb \ > rk3288-evb-act8846.dtb \ > - rk3288-evb-rk808.dtb > + rk3288-evb-rk808.dtb \ > + rk3288-firefly-beta.dtb \ > + rk3288-firefly.dtb > dtb-$(CONFIG_ARCH_S3C24XX) += \ > s3c2416-smdk2416.dtb > dtb-$(CONFIG_ARCH_S3C64XX) += \ > diff --git a/arch/arm/boot/dts/rk3288-firefly-beta.dts > b/arch/arm/boot/dts/rk3288-firefly-beta.dts new file mode 100644 > index 0000000..d640569 > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-firefly-beta.dts > @@ -0,0 +1,70 @@ > +/* > + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "rk3288-firefly.dtsi" > + > +/ { > + model = "Firefly-RK3288 Beta"; > +}; > + > +&ir { > + gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; > +}; > + > +&pwm0 { > + status = "okay"; > +}; > + > +&pinctrl { > + ir { > + ir_int: ir-int { > + rockchip,pins = <7 5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + act8846 { > + pmic_vsel: pmic-vsel { > + rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>; > + }; > + }; > +}; please order nodes a bit more. Nodes having an address (foo at ff908000 etc) should of course be ordered by this memory address or their i2c address. Nodes without address element should be ordered alphabetically, so here, act8846 before ir. Same with &pinctrl before &pwm (= phandles should also be sorted). > diff --git a/arch/arm/boot/dts/rk3288-firefly.dts > b/arch/arm/boot/dts/rk3288-firefly.dts new file mode 100644 > index 0000000..0bdc37c > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-firefly.dts > @@ -0,0 +1,70 @@ > +/* > + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "rk3288-firefly.dtsi" > + > +/ { > + model = "Firefly-RK3288"; > +}; > + > +&ir { > + gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; > +}; > + > +&pwm1 { > + status = "okay"; > +}; > + > +&pinctrl { > + ir { > + ir_int: ir-int { > + rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + act8846 { > + pmic_vsel: pmic-vsel { > + rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>; > + }; > + }; > +}; again ordering > diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi > b/arch/arm/boot/dts/rk3288-firefly.dtsi new file mode 100644 > index 0000000..5996778 > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi > @@ -0,0 +1,498 @@ > +/* > + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +#include "rk3288.dtsi" > + > +/ { > + compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; > + > + memory { > + reg = <0 0x80000000>; > + }; > + > + ext_gmac: external-gmac-clock { > + compatible = "fixed-clock"; > + clock-frequency = <125000000>; > + clock-output-names = "ext_gmac"; > + #clock-cells = <0>; > + }; > + > + ir: ir-receiver { > + compatible = "gpio-ir-receiver"; > + pinctrl-names = "default"; > + pinctrl-0 = <&ir_int>; > + }; > + > + keys: gpio-keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + button at 0 { > + gpio-key,wakeup = <1>; > + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; > + label = "GPIO Power"; > + linux,code = <116>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pwr_key>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + work { > + gpios = <&gpio8 1 GPIO_ACTIVE_LOW>; > + label = "firefly:blue:user"; > + linux,default-trigger = "rc-feedback"; > + pinctrl-names = "default"; > + pinctrl-0 = <&work_led>; > + }; > + > + power { > + gpios = <&gpio8 2 GPIO_ACTIVE_LOW>; > + label = "firefly:green:power"; > + linux,default-trigger = "default-on"; > + pinctrl-names = "default"; > + pinctrl-0 = <&power_led>; > + }; > + }; > + > + vcc_sys: vsys-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_sys"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vcc_sd: sdmmc-regulator { > + compatible = "regulator-fixed"; > + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdmmc_pwr>; > + regulator-name = "vcc_sd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <100000>; > + vin-supply = <&vcc_io>; > + }; > + > + vcc_flash: flash-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_flash"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vcc_io>; > + }; > + > + vcc_5v: usb-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + vin-supply = <&vcc_sys>; > + }; > + > + vcc_host_5v: usb-host-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&host_vbus_drv>; > + regulator-name = "vcc_host_5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + vin-supply = <&vcc_5v>; > + }; > + > + vcc_otg_5v: usb-otg-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&otg_vbus_drv>; > + regulator-name = "vcc_otg_5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + vin-supply = <&vcc_5v>; > + }; > +}; > + > +&cpu0 { > + cpu0-supply = <&vdd_cpu>; > +}; > + from here on downwards, ordering issues > +&sdmmc { > + bus-width = <4>; > + cap-mmc-highspeed; > + cap-sd-highspeed; > + card-detect-delay = <200>; > + disable-wp; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; > + status = "okay"; > + vmmc-supply = <&vcc_sd>; > + vqmmc-supply = <&vccio_sd>; > +}; > + > +&sdio0 { > + broken-cd; > + bus-width = <4>; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>; > + status = "okay"; > + vmmc-supply = <&vcc_18>; > +}; > + > +&emmc { > + broken-cd; > + bus-width = <8>; > + cap-mmc-highspeed; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>; > + status = "okay"; > + vmmc-supply = <&vcc_io>; > + vqmmc-supply = <&vcc_flash>; > +}; > + > +&saradc { > + status = "okay"; > + vref-supply = <&vcc_18>; > +}; > + > +&spi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>; > + status = "okay"; > +}; > + > +&spi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi2_clk>, <&spi2_cs0>; > + status = "okay"; > +}; > + > +&i2c1 { > + status = "okay"; > +}; > + > +&i2c4 { > + status = "okay"; > +}; > + > +&i2c5 { > + status = "okay"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; > + status = "okay"; > +}; > + > +&uart1 { > + status = "okay"; > +}; > + > +&uart2 { > + status = "okay"; > +}; > + > +&uart3 { > + status = "okay"; > +}; > + > +&tsadc { > + rockchip,hw-tshut-mode = <0>; > + /* status = "okay"; */ please don't add disabled or commented-out elements. In this case you want to keep the tsadc disabled, so the whole &tsadc nodes should not be present > +}; > + > +&gmac { > + assigned-clocks = <&cru SCLK_MAC>; > + assigned-clock-parents = <&ext_gmac>; > + clock_in_out = "input"; > + pinctrl-names = "default"; > + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>; > + phy_regulator = "vcc_lan"; > + phy-mode = "rgmii"; > + snps,reset-active-low; > + snps,reset-delays-us = <0 10000 1000000>; > + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; > + tx_delay = <0x30>; > + rx_delay = <0x10>; > + status = "ok"; > +}; > + > +&usb_host1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&usbhub_rst>; > + status = "okay"; > +}; > + > +&usb_otg { > + status = "okay"; > +}; > + > +&i2c0 { > + clock-frequency = <400000>; > + status = "okay"; > + > + vdd_cpu: syr827 at 40 { > + compatible = "silergy,syr827"; > + fcs,suspend-voltage-selector = <1>; > + reg = <0x40>; > + regulator-name = "vdd_cpu"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-boot-on; > + vin-supply = <&vcc_sys>; > + }; > + > + vdd_gpu: syr828 at 41 { > + compatible = "silergy,syr828"; > + fcs,suspend-voltage-selector = <1>; > + reg = <0x41>; > + regulator-name = "vdd_gpu"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + vin-supply = <&vcc_sys>; > + }; > + > + hym8563: hym8563 at 51 { > + compatible = "haoyu,hym8563"; > + reg = <0x51>; > + interrupt-parent = <&gpio7>; > + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&rtc_int>; > + #clock-cells = <0>; > + clock-output-names = "xin32k"; > + }; > + > + act8846: act8846 at 5a { > + compatible = "active-semi,act8846"; > + reg = <0x5a>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_vsel>, <&pwr_hold>; > + system-power-controller; > + > + regulators { > + vcc_ddr: REG1 { > + regulator-name = "vcc_ddr"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + }; > + > + vcc_io: REG2 { > + regulator-name = "vcc_io"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vdd_log: REG3 { > + regulator-name = "vdd_log"; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-always-on; > + }; > + > + vcc_20: REG4 { > + regulator-name = "vcc_20"; > + regulator-min-microvolt = <2000000>; > + regulator-max-microvolt = <2000000>; > + regulator-always-on; > + }; > + > + vccio_sd: REG5 { > + regulator-name = "vccio_sd"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vdd10_lcd: REG6 { > + regulator-name = "vdd10_lcd"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + vcca_18: REG7 { > + regulator-name = "vcca_18"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vcca_33: REG8 { > + regulator-name = "vcca_33"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vcc_lan: REG9 { > + regulator-name = "vcc_lan"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vdd_10: REG10 { > + regulator-name = "vdd_10"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + }; > + > + vcc_18: REG11 { > + regulator-name = "vcc_18"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + vcc18_lcd: REG12 { > + regulator-name = "vcc18_lcd"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > +}; > + > +&wdt { > + status = "okay"; > +}; > + > +&pinctrl { > + pcfg_output_high: pcfg-output-high { > + output-high; > + }; > + > + pcfg_output_low: pcfg-output-low { > + output-low; > + }; > + > + keys { > + pwr_key: pwr-key { > + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + leds { > + work_led: work-led { > + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + power_led: power-led { > + rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + sdmmc { > + sdmmc_pwr: sdmmc-pwr { > + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + gmac { > + phy_rst: phy-rst { > + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>; > + }; > + > + phy_pmeb: phy-pmeb { > + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + > + phy_int: phy-int { > + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + > + }; > + > + usb_host { > + host_vbus_drv: host-vbus-drv { > + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + usbhub_rst: usbhub-rst { > + rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>; > + }; > + }; > + > + usb_otg { > + otg_vbus_drv: otg-vbus-drv { > + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + hym8563 { > + rtc_int: rtc-int { > + rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + act8846 { > + pwr_hold: pwr-hold { > + rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>; > + }; > + }; ordering of pinctrl subnodes > +}; ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 2/3] ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards @ 2015-01-15 14:19 ` Heiko Stübner 0 siblings, 0 replies; 16+ messages in thread From: Heiko Stübner @ 2015-01-15 14:19 UTC (permalink / raw) To: FUKAUMI Naoki Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Please add at least a small real commit message Am Donnerstag, 15. Januar 2015, 11:40:58 schrieb FUKAUMI Naoki: > Signed-off-by: FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > --- > arch/arm/boot/dts/Makefile | 4 +- > arch/arm/boot/dts/rk3288-firefly-beta.dts | 70 +++++ > arch/arm/boot/dts/rk3288-firefly.dts | 70 +++++ > arch/arm/boot/dts/rk3288-firefly.dtsi | 498 > ++++++++++++++++++++++++++++++ 4 files changed, 641 insertions(+), 1 > deletion(-) > create mode 100644 arch/arm/boot/dts/rk3288-firefly-beta.dts > create mode 100644 arch/arm/boot/dts/rk3288-firefly.dts > create mode 100644 arch/arm/boot/dts/rk3288-firefly.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index cb686e6..fb03a2b 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -447,7 +447,9 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ > rk3066a-marsboard.dtb \ > rk3188-radxarock.dtb \ > rk3288-evb-act8846.dtb \ > - rk3288-evb-rk808.dtb > + rk3288-evb-rk808.dtb \ > + rk3288-firefly-beta.dtb \ > + rk3288-firefly.dtb > dtb-$(CONFIG_ARCH_S3C24XX) += \ > s3c2416-smdk2416.dtb > dtb-$(CONFIG_ARCH_S3C64XX) += \ > diff --git a/arch/arm/boot/dts/rk3288-firefly-beta.dts > b/arch/arm/boot/dts/rk3288-firefly-beta.dts new file mode 100644 > index 0000000..d640569 > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-firefly-beta.dts > @@ -0,0 +1,70 @@ > +/* > + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "rk3288-firefly.dtsi" > + > +/ { > + model = "Firefly-RK3288 Beta"; > +}; > + > +&ir { > + gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; > +}; > + > +&pwm0 { > + status = "okay"; > +}; > + > +&pinctrl { > + ir { > + ir_int: ir-int { > + rockchip,pins = <7 5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + act8846 { > + pmic_vsel: pmic-vsel { > + rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>; > + }; > + }; > +}; please order nodes a bit more. Nodes having an address (foo@ff908000 etc) should of course be ordered by this memory address or their i2c address. Nodes without address element should be ordered alphabetically, so here, act8846 before ir. Same with &pinctrl before &pwm (= phandles should also be sorted). > diff --git a/arch/arm/boot/dts/rk3288-firefly.dts > b/arch/arm/boot/dts/rk3288-firefly.dts new file mode 100644 > index 0000000..0bdc37c > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-firefly.dts > @@ -0,0 +1,70 @@ > +/* > + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "rk3288-firefly.dtsi" > + > +/ { > + model = "Firefly-RK3288"; > +}; > + > +&ir { > + gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; > +}; > + > +&pwm1 { > + status = "okay"; > +}; > + > +&pinctrl { > + ir { > + ir_int: ir-int { > + rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + act8846 { > + pmic_vsel: pmic-vsel { > + rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>; > + }; > + }; > +}; again ordering > diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi > b/arch/arm/boot/dts/rk3288-firefly.dtsi new file mode 100644 > index 0000000..5996778 > --- /dev/null > +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi > @@ -0,0 +1,498 @@ > +/* > + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +#include "rk3288.dtsi" > + > +/ { > + compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; > + > + memory { > + reg = <0 0x80000000>; > + }; > + > + ext_gmac: external-gmac-clock { > + compatible = "fixed-clock"; > + clock-frequency = <125000000>; > + clock-output-names = "ext_gmac"; > + #clock-cells = <0>; > + }; > + > + ir: ir-receiver { > + compatible = "gpio-ir-receiver"; > + pinctrl-names = "default"; > + pinctrl-0 = <&ir_int>; > + }; > + > + keys: gpio-keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + button@0 { > + gpio-key,wakeup = <1>; > + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; > + label = "GPIO Power"; > + linux,code = <116>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pwr_key>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + work { > + gpios = <&gpio8 1 GPIO_ACTIVE_LOW>; > + label = "firefly:blue:user"; > + linux,default-trigger = "rc-feedback"; > + pinctrl-names = "default"; > + pinctrl-0 = <&work_led>; > + }; > + > + power { > + gpios = <&gpio8 2 GPIO_ACTIVE_LOW>; > + label = "firefly:green:power"; > + linux,default-trigger = "default-on"; > + pinctrl-names = "default"; > + pinctrl-0 = <&power_led>; > + }; > + }; > + > + vcc_sys: vsys-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_sys"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vcc_sd: sdmmc-regulator { > + compatible = "regulator-fixed"; > + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdmmc_pwr>; > + regulator-name = "vcc_sd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <100000>; > + vin-supply = <&vcc_io>; > + }; > + > + vcc_flash: flash-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_flash"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vcc_io>; > + }; > + > + vcc_5v: usb-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + vin-supply = <&vcc_sys>; > + }; > + > + vcc_host_5v: usb-host-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&host_vbus_drv>; > + regulator-name = "vcc_host_5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + vin-supply = <&vcc_5v>; > + }; > + > + vcc_otg_5v: usb-otg-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&otg_vbus_drv>; > + regulator-name = "vcc_otg_5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + vin-supply = <&vcc_5v>; > + }; > +}; > + > +&cpu0 { > + cpu0-supply = <&vdd_cpu>; > +}; > + from here on downwards, ordering issues > +&sdmmc { > + bus-width = <4>; > + cap-mmc-highspeed; > + cap-sd-highspeed; > + card-detect-delay = <200>; > + disable-wp; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; > + status = "okay"; > + vmmc-supply = <&vcc_sd>; > + vqmmc-supply = <&vccio_sd>; > +}; > + > +&sdio0 { > + broken-cd; > + bus-width = <4>; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>; > + status = "okay"; > + vmmc-supply = <&vcc_18>; > +}; > + > +&emmc { > + broken-cd; > + bus-width = <8>; > + cap-mmc-highspeed; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>; > + status = "okay"; > + vmmc-supply = <&vcc_io>; > + vqmmc-supply = <&vcc_flash>; > +}; > + > +&saradc { > + status = "okay"; > + vref-supply = <&vcc_18>; > +}; > + > +&spi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>; > + status = "okay"; > +}; > + > +&spi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi2_clk>, <&spi2_cs0>; > + status = "okay"; > +}; > + > +&i2c1 { > + status = "okay"; > +}; > + > +&i2c4 { > + status = "okay"; > +}; > + > +&i2c5 { > + status = "okay"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; > + status = "okay"; > +}; > + > +&uart1 { > + status = "okay"; > +}; > + > +&uart2 { > + status = "okay"; > +}; > + > +&uart3 { > + status = "okay"; > +}; > + > +&tsadc { > + rockchip,hw-tshut-mode = <0>; > + /* status = "okay"; */ please don't add disabled or commented-out elements. In this case you want to keep the tsadc disabled, so the whole &tsadc nodes should not be present > +}; > + > +&gmac { > + assigned-clocks = <&cru SCLK_MAC>; > + assigned-clock-parents = <&ext_gmac>; > + clock_in_out = "input"; > + pinctrl-names = "default"; > + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>; > + phy_regulator = "vcc_lan"; > + phy-mode = "rgmii"; > + snps,reset-active-low; > + snps,reset-delays-us = <0 10000 1000000>; > + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; > + tx_delay = <0x30>; > + rx_delay = <0x10>; > + status = "ok"; > +}; > + > +&usb_host1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&usbhub_rst>; > + status = "okay"; > +}; > + > +&usb_otg { > + status = "okay"; > +}; > + > +&i2c0 { > + clock-frequency = <400000>; > + status = "okay"; > + > + vdd_cpu: syr827@40 { > + compatible = "silergy,syr827"; > + fcs,suspend-voltage-selector = <1>; > + reg = <0x40>; > + regulator-name = "vdd_cpu"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-boot-on; > + vin-supply = <&vcc_sys>; > + }; > + > + vdd_gpu: syr828@41 { > + compatible = "silergy,syr828"; > + fcs,suspend-voltage-selector = <1>; > + reg = <0x41>; > + regulator-name = "vdd_gpu"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + vin-supply = <&vcc_sys>; > + }; > + > + hym8563: hym8563@51 { > + compatible = "haoyu,hym8563"; > + reg = <0x51>; > + interrupt-parent = <&gpio7>; > + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&rtc_int>; > + #clock-cells = <0>; > + clock-output-names = "xin32k"; > + }; > + > + act8846: act8846@5a { > + compatible = "active-semi,act8846"; > + reg = <0x5a>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_vsel>, <&pwr_hold>; > + system-power-controller; > + > + regulators { > + vcc_ddr: REG1 { > + regulator-name = "vcc_ddr"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + }; > + > + vcc_io: REG2 { > + regulator-name = "vcc_io"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vdd_log: REG3 { > + regulator-name = "vdd_log"; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-always-on; > + }; > + > + vcc_20: REG4 { > + regulator-name = "vcc_20"; > + regulator-min-microvolt = <2000000>; > + regulator-max-microvolt = <2000000>; > + regulator-always-on; > + }; > + > + vccio_sd: REG5 { > + regulator-name = "vccio_sd"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vdd10_lcd: REG6 { > + regulator-name = "vdd10_lcd"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + vcca_18: REG7 { > + regulator-name = "vcca_18"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vcca_33: REG8 { > + regulator-name = "vcca_33"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vcc_lan: REG9 { > + regulator-name = "vcc_lan"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vdd_10: REG10 { > + regulator-name = "vdd_10"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + }; > + > + vcc_18: REG11 { > + regulator-name = "vcc_18"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + vcc18_lcd: REG12 { > + regulator-name = "vcc18_lcd"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + }; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > +}; > + > +&wdt { > + status = "okay"; > +}; > + > +&pinctrl { > + pcfg_output_high: pcfg-output-high { > + output-high; > + }; > + > + pcfg_output_low: pcfg-output-low { > + output-low; > + }; > + > + keys { > + pwr_key: pwr-key { > + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + leds { > + work_led: work-led { > + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + power_led: power-led { > + rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + sdmmc { > + sdmmc_pwr: sdmmc-pwr { > + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + gmac { > + phy_rst: phy-rst { > + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>; > + }; > + > + phy_pmeb: phy-pmeb { > + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + > + phy_int: phy-int { > + rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + > + }; > + > + usb_host { > + host_vbus_drv: host-vbus-drv { > + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + > + usbhub_rst: usbhub-rst { > + rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>; > + }; > + }; > + > + usb_otg { > + otg_vbus_drv: otg-vbus-drv { > + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; > + }; > + }; > + > + hym8563 { > + rtc_int: rtc-int { > + rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > + > + act8846 { > + pwr_hold: pwr-hold { > + rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>; > + }; > + }; ordering of pinctrl subnodes > +}; -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3066a-rayeager.dts | 457 +++++++++++++++++++++++++++++++++ 2 files changed, 458 insertions(+) create mode 100644 arch/arm/boot/dts/rk3066a-rayeager.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index fb03a2b..4c56746 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -445,6 +445,7 @@ dtb-$(CONFIG_ARCH_REALVIEW) += \ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3066a-bqcurie2.dtb \ rk3066a-marsboard.dtb \ + rk3066a-rayeager.dtb \ rk3188-radxarock.dtb \ rk3288-evb-act8846.dtb \ rk3288-evb-rk808.dtb \ diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts new file mode 100644 index 0000000..729a039 --- /dev/null +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts @@ -0,0 +1,457 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3066a.dtsi" + +/ { + model = "Rayeager PX2"; + compatible = "chipspark,rayeager-px2", "rockchip,rk3066a"; + + memory { + reg = <0x60000000 0x40000000>; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio6 1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button at 0 { + gpio-key,wakeup = <1>; + gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; + label = "GPIO Power"; + linux,code = <116>; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_key>; + }; + }; + + vsys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vsys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_otg: usb-otg-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&otg_drv>; + regulator-name = "vcc_otg"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_host: usb-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host_drv>; + regulator-name = "host-pwr"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_sata: sata-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sata_pwr>; + regulator-name = "usb_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio3 7 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwr>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + vin-supply = <&vcc_io>; + }; + + vcc_emmc: emmc-regulator { + compatible = "regulator-fixed"; + regulator-name = "emmc_vccq"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + vin-supply = <&vsys>; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_arm>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&usb_host { + pinctrl-names = "default"; + pinctrl-0 = <&hub_rst>, <&sata_reset>; + status = "okay"; +}; + +&emac { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; + + phy = <&phy0>; + phy-supply = <&vcc_rmii>; + + phy0: ethernet-phy at 0 { + reg = <0>; + }; +}; + +&mmc0 { + bus-width = <4>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; + status = "okay"; + vmmc-supply = <&vcc_sd>; +}; + +&mmc1 { + broken-cd; + bus-width = <4>; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sd1_clk>, <&sd1_cmd>, <&sd1_bus4>; + status = "okay"; + vmmc-supply = <&vccio_wl>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_rst>; + status = "okay"; + vmmc-supply = <&vcc_emmc>; + vqmmc-supply = <&vcc_emmc>; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + keys { + pwr_key: pwr-key { + rockchip,pins = <6 2 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + ir { + ir_int: ir-int { + rockchip,pins = <6 1 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + usb_otg { + otg_drv: otg-drv { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + usb_host { + host_drv: host-drv { + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_default>; + }; + + hub_rst: hub-rst { + rockchip,pins = <1 31 RK_FUNC_GPIO &pcfg_output_high>; + }; + + sata_pwr: sata-pwr { + rockchip,pins = <4 22 RK_FUNC_GPIO &pcfg_pull_default>; + }; + + sata_reset: sata-reset { + rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + emac { + rmii_rst: rmii-rst { + rockchip,pins = <1 30 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + mmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <3 7 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + ak8963 { + comp_int: comp-int { + rockchip,pins = <4 17 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + mma8452 { + gsensor_int: gsensor-int { + rockchip,pins = <4 16 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + tps { + pmic_int: pmic-int { + rockchip,pins = <6 4 RK_FUNC_GPIO &pcfg_pull_default>; + }; + + pwr_hold: pwr-hold { + rockchip,pins = <6 8 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <400000>; + + ak8963: ak8963 at d { + compatible = "asahi-kasei,ak8975"; + reg = <0xd>; + interrupt-parent = <&gpio4>; + interrupts = <17 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&comp_int>; + }; + + mma8452: mma8452 at 1d { + compatible = "fsl,mma8452"; + reg = <0x1d>; + interrupt-parent = <&gpio4>; + interrupts = <16 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gsensor_int>; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tps: tps at 2d { + reg = <0x2d>; + interrupt-parent = <&gpio6>; + interrupts = <4 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>, <&pwr_hold>; + + vcc1-supply = <&vsys>; + vcc2-supply = <&vsys>; + vcc3-supply = <&vsys>; + vcc4-supply = <&vsys>; + vcc5-supply = <&vcc_io>; + vcc6-supply = <&vcc_io>; + vcc7-supply = <&vsys>; + vccio-supply = <&vsys>; + + regulators { + vcc_rtc: regulator at 0 { + regulator-name = "vcc_rtc"; + regulator-always-on; + }; + + vcc_io: regulator at 1 { + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_arm: regulator at 2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_ddr: regulator at 3 { + regulator-name = "vcc_ddr"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc18: regulator at 5 { + regulator-name = "vcc18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vdd_11: regulator at 6 { + regulator-name = "vdd_11"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vcc_25: regulator at 7 { + regulator-name = "vcc_25"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vccio_wl: regulator at 8 { + regulator-name = "vccio_wl"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcc25_hdmi: regulator at 9 { + regulator-name = "vcc25_hdmi"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + vcca_33: regulator at 10 { + regulator-name = "vcca_33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_rmii: regulator at 11 { + regulator-name = "vcc_rmii"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc28_cif: regulator at 12 { + regulator-name = "vcc28_cif"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + }; + }; +}; + +#include "tps65910.dtsi" + +&pwm1 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_xfer>, <&uart3_cts>, <&uart3_rts>; + status = "okay"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc_25>; +}; + +&spi0 { + status = "okay"; +}; -- 2.2.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board @ 2015-01-15 2:40 ` FUKAUMI Naoki 0 siblings, 0 replies; 16+ messages in thread From: FUKAUMI Naoki @ 2015-01-15 2:40 UTC (permalink / raw) To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Cc: FUKAUMI Naoki Signed-off-by: FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3066a-rayeager.dts | 457 +++++++++++++++++++++++++++++++++ 2 files changed, 458 insertions(+) create mode 100644 arch/arm/boot/dts/rk3066a-rayeager.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index fb03a2b..4c56746 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -445,6 +445,7 @@ dtb-$(CONFIG_ARCH_REALVIEW) += \ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3066a-bqcurie2.dtb \ rk3066a-marsboard.dtb \ + rk3066a-rayeager.dtb \ rk3188-radxarock.dtb \ rk3288-evb-act8846.dtb \ rk3288-evb-rk808.dtb \ diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts new file mode 100644 index 0000000..729a039 --- /dev/null +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts @@ -0,0 +1,457 @@ +/* + * Copyright (c) 2014, 2015 FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3066a.dtsi" + +/ { + model = "Rayeager PX2"; + compatible = "chipspark,rayeager-px2", "rockchip,rk3066a"; + + memory { + reg = <0x60000000 0x40000000>; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio6 1 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + button@0 { + gpio-key,wakeup = <1>; + gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; + label = "GPIO Power"; + linux,code = <116>; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_key>; + }; + }; + + vsys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vsys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_otg: usb-otg-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&otg_drv>; + regulator-name = "vcc_otg"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_host: usb-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host_drv>; + regulator-name = "host-pwr"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_sata: sata-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sata_pwr>; + regulator-name = "usb_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio3 7 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwr>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + vin-supply = <&vcc_io>; + }; + + vcc_emmc: emmc-regulator { + compatible = "regulator-fixed"; + regulator-name = "emmc_vccq"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + vin-supply = <&vsys>; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_arm>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>; + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&usb_host { + pinctrl-names = "default"; + pinctrl-0 = <&hub_rst>, <&sata_reset>; + status = "okay"; +}; + +&emac { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; + + phy = <&phy0>; + phy-supply = <&vcc_rmii>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&mmc0 { + bus-width = <4>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; + status = "okay"; + vmmc-supply = <&vcc_sd>; +}; + +&mmc1 { + broken-cd; + bus-width = <4>; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sd1_clk>, <&sd1_cmd>, <&sd1_bus4>; + status = "okay"; + vmmc-supply = <&vccio_wl>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_rst>; + status = "okay"; + vmmc-supply = <&vcc_emmc>; + vqmmc-supply = <&vcc_emmc>; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + keys { + pwr_key: pwr-key { + rockchip,pins = <6 2 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + ir { + ir_int: ir-int { + rockchip,pins = <6 1 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + usb_otg { + otg_drv: otg-drv { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + usb_host { + host_drv: host-drv { + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_default>; + }; + + hub_rst: hub-rst { + rockchip,pins = <1 31 RK_FUNC_GPIO &pcfg_output_high>; + }; + + sata_pwr: sata-pwr { + rockchip,pins = <4 22 RK_FUNC_GPIO &pcfg_pull_default>; + }; + + sata_reset: sata-reset { + rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + emac { + rmii_rst: rmii-rst { + rockchip,pins = <1 30 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + mmc { + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <3 7 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + ak8963 { + comp_int: comp-int { + rockchip,pins = <4 17 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + mma8452 { + gsensor_int: gsensor-int { + rockchip,pins = <4 16 RK_FUNC_GPIO &pcfg_pull_default>; + }; + }; + + tps { + pmic_int: pmic-int { + rockchip,pins = <6 4 RK_FUNC_GPIO &pcfg_pull_default>; + }; + + pwr_hold: pwr-hold { + rockchip,pins = <6 8 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <400000>; + + ak8963: ak8963@d { + compatible = "asahi-kasei,ak8975"; + reg = <0xd>; + interrupt-parent = <&gpio4>; + interrupts = <17 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&comp_int>; + }; + + mma8452: mma8452@1d { + compatible = "fsl,mma8452"; + reg = <0x1d>; + interrupt-parent = <&gpio4>; + interrupts = <16 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gsensor_int>; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tps: tps@2d { + reg = <0x2d>; + interrupt-parent = <&gpio6>; + interrupts = <4 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>, <&pwr_hold>; + + vcc1-supply = <&vsys>; + vcc2-supply = <&vsys>; + vcc3-supply = <&vsys>; + vcc4-supply = <&vsys>; + vcc5-supply = <&vcc_io>; + vcc6-supply = <&vcc_io>; + vcc7-supply = <&vsys>; + vccio-supply = <&vsys>; + + regulators { + vcc_rtc: regulator@0 { + regulator-name = "vcc_rtc"; + regulator-always-on; + }; + + vcc_io: regulator@1 { + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_arm: regulator@2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_ddr: regulator@3 { + regulator-name = "vcc_ddr"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc18: regulator@5 { + regulator-name = "vcc18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vdd_11: regulator@6 { + regulator-name = "vdd_11"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vcc_25: regulator@7 { + regulator-name = "vcc_25"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vccio_wl: regulator@8 { + regulator-name = "vccio_wl"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcc25_hdmi: regulator@9 { + regulator-name = "vcc25_hdmi"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + vcca_33: regulator@10 { + regulator-name = "vcca_33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_rmii: regulator@11 { + regulator-name = "vcc_rmii"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc28_cif: regulator@12 { + regulator-name = "vcc28_cif"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + }; + }; +}; + +#include "tps65910.dtsi" + +&pwm1 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_xfer>, <&uart3_cts>, <&uart3_rts>; + status = "okay"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc_25>; +}; + +&spi0 { + status = "okay"; +}; -- 2.2.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board @ 2015-01-15 16:19 ` Heiko Stübner 0 siblings, 0 replies; 16+ messages in thread From: Heiko Stübner @ 2015-01-15 16:19 UTC (permalink / raw) To: linux-arm-kernel Hi, again, please add a small commit message and reorder nodes as described in the previous patch, some more stuff inline Am Donnerstag, 15. Januar 2015, 11:40:59 schrieb FUKAUMI Naoki: > Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> > --- [...] > + > + vsys: vsys-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vsys"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vcc_otg: usb-otg-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&otg_drv>; > + regulator-name = "vcc_otg"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; missing vin-supply > + }; > + > + vcc_host: usb-host-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&host_drv>; > + regulator-name = "host-pwr"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; missing vin-supply > + }; > + > + vcc_sata: sata-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sata_pwr>; > + regulator-name = "usb_5v"; why is it named "usb_5v"? > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; missing vin-supply > + }; > + [...] > +&emmc { > + broken-cd; > + bus-width = <8>; > + cap-mmc-highspeed; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_rst>; > + status = "okay"; > + vmmc-supply = <&vcc_emmc>; > + vqmmc-supply = <&vcc_emmc>; I checked the public schematics and surprisingly this is actually correct ... but still very strange :-) > +}; [...] > +&i2c0 { > + status = "okay"; > + clock-frequency = <400000>; > + > + ak8963: ak8963 at d { please use two chars for the address, i.e. ak8963 at 0d, same for the reg below > + compatible = "asahi-kasei,ak8975"; > + reg = <0xd>; > + interrupt-parent = <&gpio4>; > + interrupts = <17 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&comp_int>; > + }; > + > + mma8452: mma8452 at 1d { > + compatible = "fsl,mma8452"; > + reg = <0x1d>; > + interrupt-parent = <&gpio4>; > + interrupts = <16 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&gsensor_int>; > + }; > +}; Heiko ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board @ 2015-01-15 16:19 ` Heiko Stübner 0 siblings, 0 replies; 16+ messages in thread From: Heiko Stübner @ 2015-01-15 16:19 UTC (permalink / raw) To: FUKAUMI Naoki Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Hi, again, please add a small commit message and reorder nodes as described in the previous patch, some more stuff inline Am Donnerstag, 15. Januar 2015, 11:40:59 schrieb FUKAUMI Naoki: > Signed-off-by: FUKAUMI Naoki <naobsd-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > --- [...] > + > + vsys: vsys-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vsys"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vcc_otg: usb-otg-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&otg_drv>; > + regulator-name = "vcc_otg"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; missing vin-supply > + }; > + > + vcc_host: usb-host-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&host_drv>; > + regulator-name = "host-pwr"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; missing vin-supply > + }; > + > + vcc_sata: sata-regulator { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sata_pwr>; > + regulator-name = "usb_5v"; why is it named "usb_5v"? > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; missing vin-supply > + }; > + [...] > +&emmc { > + broken-cd; > + bus-width = <8>; > + cap-mmc-highspeed; > + disable-wp; > + non-removable; > + num-slots = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_rst>; > + status = "okay"; > + vmmc-supply = <&vcc_emmc>; > + vqmmc-supply = <&vcc_emmc>; I checked the public schematics and surprisingly this is actually correct ... but still very strange :-) > +}; [...] > +&i2c0 { > + status = "okay"; > + clock-frequency = <400000>; > + > + ak8963: ak8963@d { please use two chars for the address, i.e. ak8963@0d, same for the reg below > + compatible = "asahi-kasei,ak8975"; > + reg = <0xd>; > + interrupt-parent = <&gpio4>; > + interrupts = <17 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&comp_int>; > + }; > + > + mma8452: mma8452@1d { > + compatible = "fsl,mma8452"; > + reg = <0x1d>; > + interrupt-parent = <&gpio4>; > + interrupts = <16 IRQ_TYPE_EDGE_RISING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&gsensor_int>; > + }; > +}; Heiko -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board 2015-01-15 16:19 ` Heiko Stübner @ 2015-01-16 13:05 ` Naoki FUKAUMI -1 siblings, 0 replies; 16+ messages in thread From: Naoki FUKAUMI @ 2015-01-16 13:05 UTC (permalink / raw) To: linux-arm-kernel Hi, thank you for your review! On Fri, Jan 16, 2015 at 1:19 AM, Heiko St?bner <heiko@sntech.de> wrote: >> + vcc_sata: sata-regulator { >> + compatible = "regulator-fixed"; >> + enable-active-high; >> + gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&sata_pwr>; >> + regulator-name = "usb_5v"; > > why is it named "usb_5v"? it's came from schematic. I think it follows same rule as "vcc_host { regulator-name = "host-pwr"; }" in rk3188-radxarock.dts. I'll include rest of your comments in v2. Regards, ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board @ 2015-01-16 13:05 ` Naoki FUKAUMI 0 siblings, 0 replies; 16+ messages in thread From: Naoki FUKAUMI @ 2015-01-16 13:05 UTC (permalink / raw) To: Heiko Stübner Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r Hi, thank you for your review! On Fri, Jan 16, 2015 at 1:19 AM, Heiko Stübner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org> wrote: >> + vcc_sata: sata-regulator { >> + compatible = "regulator-fixed"; >> + enable-active-high; >> + gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&sata_pwr>; >> + regulator-name = "usb_5v"; > > why is it named "usb_5v"? it's came from schematic. I think it follows same rule as "vcc_host { regulator-name = "host-pwr"; }" in rk3188-radxarock.dts. I'll include rest of your comments in v2. Regards, -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2015-01-16 13:05 UTC | newest] Thread overview: 16+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2015-01-15 2:40 [PATCH 0/3] add support for Firefly-RK3288 and Rayeager PX2 boards FUKAUMI Naoki 2015-01-15 2:40 ` FUKAUMI Naoki 2015-01-15 2:40 ` [PATCH 1/3] dt-bindings: add vendor prefix and root compatible property for Rockchip boards FUKAUMI Naoki 2015-01-15 2:40 ` FUKAUMI Naoki 2015-01-15 14:12 ` Heiko Stübner 2015-01-15 14:12 ` Heiko Stübner 2015-01-15 2:40 ` [PATCH 2/3] ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards FUKAUMI Naoki 2015-01-15 2:40 ` FUKAUMI Naoki 2015-01-15 14:19 ` Heiko Stübner 2015-01-15 14:19 ` Heiko Stübner 2015-01-15 2:40 ` [PATCH 3/3] ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board FUKAUMI Naoki 2015-01-15 2:40 ` FUKAUMI Naoki 2015-01-15 16:19 ` Heiko Stübner 2015-01-15 16:19 ` Heiko Stübner 2015-01-16 13:05 ` Naoki FUKAUMI 2015-01-16 13:05 ` Naoki FUKAUMI
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.