Problems with bpq-interface

Problems with bpq-interface

[Florian Zagler]

Hi all,

I have problems getting the bpq0 interface work.
My computers are running Debian Woody (kiss and bpq) and Mandrake 9.1 
(bpq) and the problem is on both.

I use the following command to bring it up:

ifconfig bpq0 hw ax25 DG1CAD-12 up

In the /etc/axports file I have the following entries:

kiss    DG1CAD-10       19200   255     7       KISS TNC
ether   DG1CAD-12       100000  255     7       BPQ/ethernet

But I get the following message everytime I try to access this interface:

----    snip    ----
gateway:~# axparms -route add ether dg1cad-12
axconfig: port ether not active
axparms: invalid port name - ether
gateway:~#
----    snip    ----

I didn't find a solution in the AX25-HOWTO and the manpages.

Is there a bug or do I use the wrong commands?

Regards,
Florian

Re: Problems with bpq-interface

[pa3gcu]

On Wednesday 28 May 2003 12:45, Florian Zagler wrote:
> Hi all,
>
> I have problems getting the bpq0 interface work.
> My computers are running Debian Woody (kiss and bpq) and Mandrake 9.1
> (bpq) and the problem is on both.
>
> I use the following command to bring it up:
>
> ifconfig bpq0 hw ax25 DG1CAD-12 up
>
> In the /etc/axports file I have the following entries:
>
> kiss    DG1CAD-10       19200   255     7       KISS TNC
> ether   DG1CAD-12       100000  255     7       BPQ/ethernet
>
> But I get the following message everytime I try to access this interface:
>
> ----    snip    ----
> gateway:~# axparms -route add ether dg1cad-12
> axconfig: port ether not active
> axparms: invalid port name - ether
> gateway:~#
> ----    snip    ----

Its been a while since i used bpq, but as far as i see it you need to use 
ifconfig as follows.

ifconfig bpq0 IP# hw ax25 DG1CAD-12 up

You also need to tell the interface via bpqparms which computer to listen for;

bpqparms -d mac_of_remote_machine;
bpqparms bpq0 -d 12:34:56:B9:xx

> I didn't find a solution in the AX25-HOWTO and the manpages.
>
> Is there a bug or do I use the wrong commands?

It all used to work fine for me, some commands may have changed some check the 
man pages for bpqparms.

> Regards,
> Florian
>

-- 
Regards Richard
pa3gcu@zeelandnet.nl
http://people.zeelandnet.nl/pa3gcu/

Re: Problems with bpq-interface

[Thomas Osterried]

> ifconfig bpq0 hw ax25 DG1CAD-12 up
> 
> In the /etc/axports file I have the following entries:
> 
> kiss    DG1CAD-10       19200   255     7       KISS TNC
> ether   DG1CAD-12       100000  255     7       BPQ/ethernet
> 
> But I get the following message everytime I try to access this interface:
> 
> ----    snip    ----
> gateway:~# axparms -route add ether dg1cad-12
> axconfig: port ether not active
> axparms: invalid port name - ether
> gateway:~#
> ----    snip    ----

bpq needs an IP address to run.
this should be enough:
ifconfig bpq0 44.130.x.y up
                     ^(your ampr IP. because it's internal, i suggest 44.128.0.2) 
axparms -setcall bpq0 DG1CAD-12

"ether" in axports: bpq0 is referenced as "bpq0". afaik, nameif (interface
naming) on bpqether interfaces is -unfortunately- not supported.

you should change it to
kiss    DG1CAD-10       19200   255     7       KISS TNC
bpq0   DG1CAD-12       100000  255     7       BPQ/ethernet

73,
	- thomas  dl9sau

Re: Problems with bpq-interface

[Shane Deering]

On Wed, 28 May 2003 20:45, Florian Zagler wrote:
> Hi all,
>
> I have problems getting the bpq0 interface work.
> My computers are running Debian Woody (kiss and bpq) and Mandrake 9.1
> (bpq) and the problem is on both.
>
> I use the following command to bring it up:
>
> ifconfig bpq0 hw ax25 DG1CAD-12 up
>
> In the /etc/axports file I have the following entries:
>
> kiss    DG1CAD-10       19200   255     7       KISS TNC
> ether   DG1CAD-12       100000  255     7       BPQ/ethernet
>
> But I get the following message everytime I try to access this interface:
>
> ----    snip    ----
> gateway:~# axparms -route add ether dg1cad-12
> axconfig: port ether not active
> axparms: invalid port name - ether
> gateway:~#
> ----    snip    ----
>
> I didn't find a solution in the AX25-HOWTO and the manpages.
>
> Is there a bug or do I use the wrong commands?

The following is what I do to start bpqether on two boxes here.
It works fine. One thing I should do is replace vk3bvp-6 with a bogus 
callsign.

----Mandrake end---
# /etc/ax25/axports
tofbb	vk3bvp-6 	57600	255	6	link to fbb

# This is on the end of rc.local
modprobe bpqether
/sbin/ifconfig bpq0 192.168.1.6 hw ax25 vk3bvp-6 up
echo "bpqether started"

---Redhat end---
# /etc/ax25/axports
ether	eth-0  		10000000	255	6	ethernet port

# In the middle of my ax25 startup script
/sbin/ifconfig bpq0 192.168.1.3 hw ax25 eth-0 up

---Unproto seen on Redhat end---
ether: fm VK3BVP-6 to VK3BVP ctl SABM+ 
ether: fm VK3BVP to VK3BVP-6 ctl UA- 

-- 
Shane Deering                   Sent using Kmail v1.4.3
vk3bvp@qsl.net                  on Mandrake Linux, the Desktop OS
vk3bvp@vk3bvp.#sev.vic.aus.oc   MDK9.0 Up 6 hours and 47 minutes 
http://www.qsl.net/vk3bvp/      RH7.2 Up 5 days, 4 hours and 10 minutes 

Solved: Problems with bpq-interface

[Florian Zagler]

Hi all,

after two hints the problem ist solved and bpq is working.

Thank's

Regards
Florian