All of lore.kernel.org
 help / color / mirror / Atom feed
* Promise Ultra100TX2 PDC20286 broken in 2.6.0-test9
@ 2003-11-08 20:25 David Greaves
  2003-11-26 22:50 ` David Greaves
  0 siblings, 1 reply; 4+ messages in thread
From: David Greaves @ 2003-11-08 20:25 UTC (permalink / raw)
  To: linux-ide

Repost to linux-ide so I've quoted the entire message.
(please cc me in replies:  lkml at dgreaves.com)

Summary:
PDC20286 fails horribly with 2 UDMA drives on its primary channel
If I move one drive to the second channel it seems OK.


I have compiled with and without "DMA on by default".
I've also used the autotune options (and ata66)
I looked for the most conservative config I could find before posting 
(well, I thought I did) :)

ok...
I tried again with:
* DMA on by default (IDEDMA_PCI_AUTO) (done a partial config dump later...)
* removed noapic and used both autotune options (not tried before)
  kernel /vmlinuz-2.6.0-test9 ro root=/dev/hdc3 ide2=autotune 
ide3=autotune single
 
Result:
same problem with this dmesg (text continues after this dmesg dump)
/##########//##########//##########//##########//##########//##########
//[root@willow root]# cat dmesg_pdc20268_problem_for_bart
Linux version 2.6.0-test9 (root@willow) (gcc version 2.96 20000731 (Red 
Hat Linux 7.3 2.96-110)) #5 Sat Nov 8 19:10:59 GMT 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000010ff0000 (usable)
 BIOS-e820: 0000000010ff0000 - 0000000010ff3000 (ACPI NVS)
 BIOS-e820: 0000000010ff3000 - 0000000011000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
271MB LOWMEM available.
On node 0 totalpages: 69616
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 65520 pages, LIFO batch:15
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Building zonelist for node : 0
Kernel command line: ro root=/dev/hdc3 ide2=autotune ide3=autotune single
ide_setup: ide2=autotune
ide_setup: ide3=autotune
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 451.101 MHz processor.
Console: colour VGA+ 80x25
Memory: 271812k/278464k available (2116k kernel code, 5936k reserved, 
750k data, 120k init, 0k highmem)
Calibrating delay loop... 888.83 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU:     After generic identify, caps: 008021bf 808029bf 00000000 00000000
CPU:     After vendor identify, caps: 008021bf 808029bf 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: L2 Cache: 256K (32 bytes/line)
CPU:     After all inits, caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D+ Processor stepping 01
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc0e8, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0586] at 0000:00:07.0
Machine check exception polling timer started.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
SGI XFS for Linux with no debug enabled
Activating ISA DMA hang workarounds.
pty: 256 Unix98 ptys configured
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST320420A, ATA DISK drive
hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: IBM-DTLA-305040, ATA DISK drive
hdd: IC35L060AVVA07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20268: IDE controller at PCI slot 0000:00:09.0
PCI: Found IRQ 10 for device 0000:00:09.0
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0xe8000000
PDC20268: 100% native mode on irq 10
    ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD800JB-00ETA0, ATA DISK drive
hdf: WDC WD800JB-00ETA0, ATA DISK drive
hdf: set_drive_speed_status: status=0xff { Busy }
Warning: Primary channel requires an 80-pin cable for operation.
hdf reduced to Ultra33 mode.
hdf: set_drive_speed_status: status=0xff { Busy }
ide2 at 0xd800-0xd807,0xdc02 on irq 10
hda: max request size: 128KiB
hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63, UDMA(33)
 hda: hda1 hda2
hdc: max request size: 128KiB
hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63, UDMA(33)
 hdc: hdc1 hdc2 hdc3
hdd: max request size: 128KiB
hdd: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(33)
 hdd: hdd1
hde: max request size: 1024KiB
hde: status timeout: status=0xff { Busy }

hde: drive not ready for command
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, 
UDMA(100)
hde: status timeout: status=0xff { Busy }

hde: drive not ready for command
 hde:hde: status timeout: status=0xff { Busy }

hde: DMA disabled
hdf: DMA disabled
PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
hde: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev hde, sector 0
Buffer I/O error on device hde, logical block 0
end_request: I/O error, dev hde, sector 0
Buffer I/O error on device hde, logical block 0
 unable to read partition table
hdf: max request size: 1024KiB
hdf: status timeout: status=0xff { Busy }

hdf: drive not ready for command
hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
hdf: status timeout: status=0xff { Busy }

hdf: drive not ready for command
 hdf:hdf: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
hdf: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev hdf, sector 0
Buffer I/O error on device hdf, logical block 0
end_request: I/O error, dev hdf, sector 0
Buffer I/O error on device hdf, logical block 0
 unable to read partition table
end_request: I/O error, dev hdb, sector 0
hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.12
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 
19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
ALSA device list:
  No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
UDF-fs DEBUG fs/udf/lowlevel.c:65:udf_get_last_session: 
CDROMMULTISESSION not supported: rc=-22
UDF-fs DEBUG fs/udf/super.c:1544:udf_fill_super: Multi-session=0
UDF-fs DEBUG fs/udf/super.c:531:udf_vrs: Starting at sector 16 (2048 
byte sectors)
UDF-fs: No VRS found
XFS mounting filesystem hdc3
Ending clean XFS mount for filesystem: hdc3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding 512056k swap on /dev/hdc2.  Priority:-1 extents:1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
XFS mounting filesystem hdd1
Ending clean XFS mount for filesystem: hdd1
XFS mounting filesystem hdc1
Ending clean XFS mount for filesystem: hdc1
XFS mounting filesystem hda2
Ending clean XFS mount for filesystem: hda2
hdb: DMA disabled
//##########//##########//##########//##########//##########//##########
/
You asked why are both drives on one channel - I only had one 80-strand 
cable to hand!
Also one drive is mounted rw and used - the other is ro and contains 
rsync snapshots so is only used in the wee small hours.
...but I dug another cable from another machine and tried that.
The disks were jumpered "master w/ slave" and "slave"
I moved them both to "master w/ slave"  and the BIOS didn't recognise them
I jumpered them both as "single master" and the BIOS saw them.

***I rebooted the same kernel/params and it worked.***

/##########//##########//##########//##########//##########//##########
/[root@willow root]# cat dmesg_pdc20268_problem_for_bart_2channel
Linux version 2.6.0-test9 (root@willow) (gcc version 2.96 20000731 (Red 
Hat Linux 7.3 2.96-110)) #5 Sat Nov 8 19:10:59 GMT 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000010ff0000 (usable)
 BIOS-e820: 0000000010ff0000 - 0000000010ff3000 (ACPI NVS)
 BIOS-e820: 0000000010ff3000 - 0000000011000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
271MB LOWMEM available.
On node 0 totalpages: 69616
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 65520 pages, LIFO batch:15
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Building zonelist for node : 0
Kernel command line: ro root=/dev/hdc3 ide2=autotune ide3=autotune single
ide_setup: ide2=autotune
ide_setup: ide3=autotune
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 451.085 MHz processor.
Console: colour VGA+ 80x25
Memory: 271812k/278464k available (2116k kernel code, 5936k reserved, 
750k data, 120k init, 0k highmem)
Calibrating delay loop... 888.83 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU:     After generic identify, caps: 008021bf 808029bf 00000000 00000000
CPU:     After vendor identify, caps: 008021bf 808029bf 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: L2 Cache: 256K (32 bytes/line)
CPU:     After all inits, caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D+ Processor stepping 01
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc0e8, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0586] at 0000:00:07.0
Machine check exception polling timer started.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
SGI XFS for Linux with no debug enabled
Activating ISA DMA hang workarounds.
pty: 256 Unix98 ptys configured
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST320420A, ATA DISK drive
hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: IBM-DTLA-305040, ATA DISK drive
hdd: IC35L060AVVA07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20268: IDE controller at PCI slot 0000:00:09.0
PCI: Found IRQ 10 for device 0000:00:09.0
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0xe8000000
PDC20268: 100% native mode on irq 10
    ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD800JB-00ETA0, ATA DISK drive
ide2 at 0xd800-0xd807,0xdc02 on irq 10
hdg: WDC WD800JB-00ETA0, ATA DISK drive
ide3 at 0xe000-0xe007,0xe402 on irq 10
hda: max request size: 128KiB
hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63, UDMA(33)
 hda: hda1 hda2
hdc: max request size: 128KiB
hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63, UDMA(33)
 hdc: hdc1 hdc2 hdc3
hdd: max request size: 128KiB
hdd: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(33)
 hdd: hdd1
hde: max request size: 1024KiB
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, 
UDMA(100)
 hde: hde1
hdg: max request size: 1024KiB
hdg: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, 
UDMA(100)
 hdg: hdg1
end_request: I/O error, dev hdb, sector 0
hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.12
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 
19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
ALSA device list:
  No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
UDF-fs DEBUG fs/udf/lowlevel.c:65:udf_get_last_session: 
CDROMMULTISESSION not supported: rc=-22
UDF-fs DEBUG fs/udf/super.c:1544:udf_fill_super: Multi-session=0
UDF-fs DEBUG fs/udf/super.c:531:udf_vrs: Starting at sector 16 (2048 
byte sectors)
UDF-fs: No VRS found
XFS mounting filesystem hdc3
Ending clean XFS mount for filesystem: hdc3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding 512056k swap on /dev/hdc2.  Priority:-1 extents:1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
XFS mounting filesystem hdd1
Ending clean XFS mount for filesystem: hdd1
XFS mounting filesystem hdc1
Ending clean XFS mount for filesystem: hdc1
XFS mounting filesystem hda2
Ending clean XFS mount for filesystem: hda2
XFS mounting filesystem hde1
Ending clean XFS mount for filesystem: hde1
/##########//##########//##########//##########//##########//##########///

For the hell of it I tried it without the autotune parameters and it was 
still fine...
It looks like something doesn't work with 2 drives on 1 channel.

Also does this help?
[root@willow linux-2.6.0-test9]# grep -E "BLK_DEV|IDE" .config
CONFIG_BLK_DEV_FD=y
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# Please see Documentation/ide.txt for help/info on IDE drives
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_IDEDISK_STROKE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_IDE_TASKFILE_IO is not set
# IDE chipset support/bugfixes
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_IDEDMA_ONLYDISK=y
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_IVB=y
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
# CONFIG_BLK_DEV_SD is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
CONFIG_BLK_DEV_MD=m
CONFIG_BLK_DEV_DM=m
# CONFIG_VIDEO_DEV is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_TRIDENT is not set
# CONFIG_SND_TRIDENT is not set



David


> Hi,
>
> Can you try "ide2=autotune ide3=autotune" boot parameters?
>
> Promise driver is not autotuning PIO modes by default (will be fixed soon,
> needs some more testing). You are hitting it only in 2.6.0-t9 because 
> you've
> compiled kernel without "DMA on by default" (guess based on your dmesg),
> plus in 2.4.18 you are passing "ide2=autotune" parameter.
>
> Off-topic: you have two drives on the first channel, second channel is 
> free.
> Why not move one of drives to the second channel?
>
> Please post ide bugreports on linux-ide@xxxxxxxxxxxxxxx next time.
>
> thanks,
> --bartlomiej
>
> On Saturday 08 of November 2003 17:51, David Greaves wrote:
> >/ Summary: The Promise Ultra100TX2 doesn't work for me in 2.6.0-test9 -/
> >/ but it is fine with 2.4.18xfs/
> >
> >/ (First posting to lkml - hopefully got enough info and this will be/
> >/ helpful - let me know if you need more.)/
> >/ I've been googling, recompiling and trying for 12 hours now so I've 
> seen/
> >/ a lot of stuff about the promise drivers :)/
> >
> >/ My basic system is RedHat 7.3 with XFS. The kernel is non std (has 
> XFS +/
> >/ misc ACL patch) 2.4.18/
> >
> >/ I am using the 80pin cable supplied with the Promise./
> >/ I've tried the 'noapic' option (and config'ed without any power/
> >/ management) as Alan Cox suggested/
> >
> >/ Below is trimmed dmesg from 2.4.18 and complete dmesg from 2.6.0-test9/
> >
> >/ Please cc lkml at dgreaves.com in replies./
> >
> >/ grub for 2.4.18: kernel /vmlinuz-2.4.18-4SGI_XFS_1.1customIDE ro/
> >/ root=/dev/hdc3 ide2=ata66 ide2=autotune/
> >/ (Relevant bit from 2.4.18 dmesg:/
> >/ #########################/
> >/ Uniform Multi-Platform E-IDE driver Revision: 6.31/
> >/ ide: Assuming 33MHz system bus speed for PIO modes; override with 
> idebus=xx/
> >/ VP_IDE: IDE controller on PCI bus 00 dev 39/
> >/ VP_IDE: chipset revision 6/
> >/ VP_IDE: not 100% native mode: will probe irqs later/
> >/ VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1/
> >/ ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA/
> >/ ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA/
> >/ PDC20268: IDE controller on PCI bus 00 dev 48/
> >/ PCI: Found IRQ 10 for device 00:09.0/
> >/ PDC20268: chipset revision 2/
> >/ PDC20268: not 100% native mode: will probe irqs later/
> >/ PDC20268: ROM enabled at 0xe8000000/
> >/ PDC20268: ATA-66/100 forced bit set (WARNING)!!/
> >/ ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio/
> >/ ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio/
> >/ hda: ST320420A, ATA DISK drive/
> >/ hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive/
> >/ hdc: IBM-DTLA-305040, ATA DISK drive/
> >/ hdd: IC35L060AVVA07-0, ATA DISK drive/
> >/ hde: WDC WD800JB-00ETA0, ATA DISK drive/
> >/ hdf: WDC WD800JB-00ETA0, ATA DISK drive/
> >/ ide0 at 0x1f0-0x1f7,0x3f6 on irq 14/
> >/ ide1 at 0x170-0x177,0x376 on irq 15/
> >/ ide2 at 0xd800-0xd807,0xdc02 on irq 10/
> >/ hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=2480/255/63, 
> UDMA(33)/
> >/ hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, 
> UDMA(33)/
> >/ hdd: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63,/
> >/ UDMA(33)/
> >/ blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)/
> >/ hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63,/
> >/ UDMA(100)/
> >/ blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)/
> >/ hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63,/
> >/ UDMA(100)/
> >/ Partition check:/
> >/ hda: hda1 hda2/
> >/ hdc: hdc1 hdc2 hdc3/
> >/ hdd: hdd1/
> >/ hde: hde1/
> >/ hdf: hdf1/
> >/ [snip]/
> >/ md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27/
> >/ XFS mounting filesystem ide0(3,1)/
> >/ XFS mounting filesystem ide1(22,65)/
> >/ XFS mounting filesystem ide1(22,1)/
> >/ XFS mounting filesystem ide0(3,2)/
> >/ XFS mounting filesystem ide2(33,1)/
> >/ XFS mounting filesystem ide2(33,65)/
> >/ hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache, DMA/
> >/ Uniform CD-ROM driver Revision: 3.12/
> >/ hdb: packet command error: status=0x51 { DriveReady SeekComplete 
> Error }/
> >/ hdb: packet command error: error=0x00/
> >/ hdb: DMA disabled/
> >/ ide0: Speed warnings UDMA 3/4/5 is not functional./
> >/ ide1: Speed warnings UDMA 3/4/5 is not functional./
> >/ ide1: Speed warnings UDMA 3/4/5 is not functional./
> >/ blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)/
> >/ blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)/
> >/ #########################/
> >
> >/ and from 2.6.0-test9/
> >/ #########################/
> >/ Linux version 2.6.0-test9 (root@willow) (gcc version 2.96 20000731 
> (Red/
> >/ Hat Linux 7.3 2.96-110)) #2 Sat Nov 8 15:56:56 GMT 2003/
> >/ BIOS-provided physical RAM map:/
> >/ BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)/
> >/ BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)/
> >/ BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)/
> >/ BIOS-e820: 0000000000100000 - 0000000010ff0000 (usable)/
> >/ BIOS-e820: 0000000010ff0000 - 0000000010ff3000 (ACPI NVS)/
> >/ BIOS-e820: 0000000010ff3000 - 0000000011000000 (ACPI data)/
> >/ BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)/
> >/ 271MB LOWMEM available./
> >/ On node 0 totalpages: 69616/
> >/ DMA zone: 4096 pages, LIFO batch:1/
> >/ Normal zone: 65520 pages, LIFO batch:15/
> >/ HighMem zone: 0 pages, LIFO batch:1/
> >/ DMI 2.2 present./
> >/ Building zonelist for node : 0/
> >/ Kernel command line: ro root=/dev/hdc3 noapic single/
> >/ Initializing CPU#0/
> >/ PID hash table entries: 2048 (order 11: 16384 bytes)/
> >/ Detected 451.117 MHz processor./
> >/ Console: colour VGA+ 80x25/
> >/ Memory: 271812k/278464k available (2117k kernel code, 5936k reserved,/
> >/ 753k data, 120k init, 0k highmem)/
> >/ Calibrating delay loop... 888.83 BogoMIPS/
> >/ Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)/
> >/ Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)/
> >/ Mount-cache hash table entries: 512 (order: 0, 4096 bytes)/
> >/ CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000/
> >/ CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000/
> >/ CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)/
> >/ CPU: L2 Cache: 256K (32 bytes/line)/
> >/ CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002/
> >/ CPU: AMD-K6(tm) 3D+ Processor stepping 01/
> >/ Checking 'hlt' instruction... OK./
> >/ POSIX conformance testing by UNIFIX/
> >/ NET: Registered protocol family 16/
> >/ PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1/
> >/ PCI: Using configuration type 1/
> >/ mtrr: v2.0 (20020519)/
> >/ Linux Plug and Play Support v0.97 (c) Adam Belay/
> >/ PnPBIOS: Scanning system for PnP BIOS support.../
> >/ PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0c0/
> >/ PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc0e8, dseg 0xf0000/
> >/ PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver/
> >/ SCSI subsystem initialized/
> >/ drivers/usb/core/usb.c: registered new driver usbfs/
> >/ drivers/usb/core/usb.c: registered new driver hub/
> >/ PCI: Probing PCI hardware/
> >/ PCI: Probing PCI hardware (bus 00)/
> >/ PCI: Using IRQ router VIA [1106/0586] at 0000:00:07.0/
> >/ Machine check exception polling timer started./
> >/ Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx)./
> >/ udf: registering filesystem/
> >/ SGI XFS for Linux with no debug enabled/
> >/ Activating ISA DMA hang workarounds./
> >/ pty: 256 Unix98 ptys configured/
> >/ Linux agpgart interface v0.100 (c) Dave Jones/
> >/ Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing 
> disabled/
> >/ ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A/
> >/ ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A/
> >/ Using anticipatory io scheduler/
> >/ Floppy drive(s): fd0 is 1.44M/
> >/ FDC 0 is a post-1991 82077/
> >/ Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2/
> >/ ide: Assuming 33MHz system bus speed for PIO modes; override with 
> idebus=xx/
> >/ VP_IDE: IDE controller at PCI slot 0000:00:07.1/
> >/ VP_IDE: chipset revision 6/
> >/ VP_IDE: not 100% native mode: will probe irqs later/
> >/ ide: Assuming 33MHz system bus speed for PIO modes; override with 
> idebus=xx/
> >/ VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on 
> pci0000:00:07.1/
> >/ ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA/
> >/ ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA/
> >/ hda: ST320420A, ATA DISK drive/
> >/ hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive/
> >/ ide0 at 0x1f0-0x1f7,0x3f6 on irq 14/
> >/ hdc: IBM-DTLA-305040, ATA DISK drive/
> >/ hdd: IC35L060AVVA07-0, ATA DISK drive/
> >/ ide1 at 0x170-0x177,0x376 on irq 15/
> >/ PDC20268: IDE controller at PCI slot 0000:00:09.0/
> >/ PCI: Found IRQ 10 for device 0000:00:09.0/
> >/ PDC20268: chipset revision 2/
> >/ PDC20268: ROM enabled at 0xe8000000/
> >/ PDC20268: 100% native mode on irq 10/
> >/ ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio/
> >/ ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio/
> >/ hde: WDC WD800JB-00ETA0, ATA DISK drive/
> >/ hdf: WDC WD800JB-00ETA0, ATA DISK drive/
> >/ hdf: set_drive_speed_status: status=0xff { Busy }/
> >/ ide2 at 0xd800-0xd807,0xdc02 on irq 10/
> >/ hda: max request size: 128KiB/
> >/ hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63/
> >/ hda: hda1 hda2/
> >/ hdc: max request size: 128KiB/
> >/ hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63/
> >/ hdc: hdc1 hdc2 hdc3/
> >/ hdd: max request size: 128KiB/
> >/ hdd: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63/
> >/ hdd: hdd1/
> >/ hde: max request size: 1024KiB/
> >/ hde: status timeout: status=0xff { Busy }/
> >
> >/ hde: drive not ready for command/
> >/ hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63/
> >/ hde: status timeout: status=0xff { Busy }/
> >
> >/ hde: drive not ready for command/
> >/ hde:hde: status timeout: status=0xff { Busy }/
> >
> >/ PDC202XX: Primary channel reset./
> >/ hde: drive not ready for command/
> >/ ide2: reset timed-out, status=0xff/
> >/ hde: status timeout: status=0xff { Busy }/
> >
> >/ PDC202XX: Primary channel reset./
> >/ hde: drive not ready for command/
> >/ ide2: reset timed-out, status=0xff/
> >/ end_request: I/O error, dev hde, sector 0/
> >/ Buffer I/O error on device hde, logical block 0/
> >/ end_request: I/O error, dev hde, sector 0/
> >/ Buffer I/O error on device hde, logical block 0/
> >/ unable to read partition table/
> >/ hdf: max request size: 1024KiB/
> >/ hdf: status timeout: status=0xff { Busy }/
> >
> >/ hdf: drive not ready for command/
> >/ hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63/
> >/ hdf: status timeout: status=0xff { Busy }/
> >
> >/ hdf: drive not ready for command/
> >/ hdf:hdf: status timeout: status=0xff { Busy }/
> >
> >/ PDC202XX: Primary channel reset./
> >/ hdf: drive not ready for command/
> >/ ide2: reset timed-out, status=0xff/
> >/ hdf: status timeout: status=0xff { Busy }/
> >
> >/ PDC202XX: Primary channel reset./
> >/ hdf: drive not ready for command/
> >/ ide2: reset timed-out, status=0xff/
> >/ end_request: I/O error, dev hdf, sector 0/
> >/ Buffer I/O error on device hdf, logical block 0/
> >/ end_request: I/O error, dev hdf, sector 0/
> >/ Buffer I/O error on device hdf, logical block 0/
> >/ unable to read partition table/
> >/ end_request: I/O error, dev hdb, sector 0/
> >/ hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache/
> >/ Uniform CD-ROM driver Revision: 3.12/
> >/ drivers/usb/core/usb.c: registered new driver usblp/
> >/ drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver/
> >/ drivers/usb/core/usb.c: registered new driver hid/
> >/ drivers/usb/input/hid-core.c: v2.0:USB HID core driver/
> >/ mice: PS/2 mouse device common for all mice/
> >/ input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1/
> >/ serio: i8042 AUX port at 0x60,0x64 irq 12/
> >/ input: AT Translated Set 2 keyboard on isa0060/serio0/
> >/ serio: i8042 KBD port at 0x60,0x64 irq 1/
> >/ Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25/
> >/ 19:16:36 2003 UTC)./
> >/ request_module: failed /sbin/modprobe -- snd-card-0. error = -16/
> >/ ALSA device list:/
> >/ No soundcards found./
> >/ NET: Registered protocol family 2/
> >/ IP: routing cache hash table of 2048 buckets, 16Kbytes/
> >/ TCP: Hash tables configured (established 32768 bind 32768)/
> >/ NET: Registered protocol family 1/
> >/ UDF-fs DEBUG fs/udf/lowlevel.c:65:udf_get_last_session:/
> >/ CDROMMULTISESSION not supported: rc=-22/
> >/ UDF-fs DEBUG fs/udf/super.c:1544:udf_fill_super: Multi-session=0/
> >/ UDF-fs DEBUG fs/udf/super.c:531:udf_vrs: Starting at sector 16 (2048/
> >/ byte sectors)/
> >/ UDF-fs: No VRS found/
> >/ XFS mounting filesystem hdc3/
> >/ Ending clean XFS mount for filesystem: hdc3/
> >/ VFS: Mounted root (xfs filesystem) readonly./
> >/ Freeing unused kernel memory: 120k freed/
> >/ Adding 512056k swap on /dev/hdc2. Priority:-1 extents:1/
> >/ md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27/
> >/ XFS mounting filesystem hda1/
> >/ Ending clean XFS mount for filesystem: hda1/
> >/ XFS mounting filesystem hdd1/
> >/ Ending clean XFS mount for filesystem: hdd1/
> >/ XFS mounting filesystem hdc1/
> >/ Ending clean XFS mount for filesystem: hdc1/
> >/ XFS mounting filesystem hda2/
> >/ Ending clean XFS mount for filesystem: hda2/
> >/ hdb: DMA disabled/
> >/ hda: Speed warnings UDMA 3/4/5 is not functional./
> >/ ide1: Speed warnings UDMA 3/4/5 is not functional./
> >/ ide1: Speed warnings UDMA 3/4/5 is not functional./
> >/ end_request: I/O error, dev hde, sector 0/
> >/ hde: set_drive_speed_status: status=0xff { Busy }/
> >/ end_request: I/O error, dev hde, sector 0/
> >/ hde: set_drive_speed_status: status=0xff { Busy }/
> >/ end_request: I/O error, dev hde, sector 0/
> >/ end_request: I/O error, dev hdf, sector 0/
> >/ hdf: set_drive_speed_status: status=0xff { Busy }/
> >/ end_request: I/O error, dev hdf, sector 0/
> >/ hdf: set_drive_speed_status: status=0xff { Busy }/
> >/ end_request: I/O error, dev hdf, sector 0/
>



^ permalink raw reply	[flat|nested] 4+ messages in thread
* Promise Ultra100TX2 PDC20286 broken in 2.6.0-test9
@ 2003-11-08 16:51 David Greaves
  2003-11-08 17:18 ` Bartlomiej Zolnierkiewicz
  0 siblings, 1 reply; 4+ messages in thread
From: David Greaves @ 2003-11-08 16:51 UTC (permalink / raw)
  To: linux-kernel

Summary: The Promise Ultra100TX2 doesn't work for me in 2.6.0-test9 - 
but it is fine with 2.4.18xfs

(First posting to lkml - hopefully got enough info and this will be 
helpful - let me know if you need more.)
I've been googling, recompiling and trying for 12 hours now so I've seen 
a lot of stuff about the promise drivers :)

My basic system is RedHat 7.3 with XFS. The kernel is non std (has XFS + 
misc ACL patch) 2.4.18

I am using the 80pin cable supplied with the Promise.
I've tried the 'noapic' option (and config'ed without any power 
management) as Alan Cox suggested

Below is trimmed dmesg from 2.4.18 and complete dmesg from 2.6.0-test9

Please cc lkml at dgreaves.com in replies.

grub for 2.4.18: kernel /vmlinuz-2.4.18-4SGI_XFS_1.1customIDE ro 
root=/dev/hdc3 ide2=ata66 ide2=autotune
(Relevant bit from 2.4.18 dmesg:
#########################
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
PDC20268: IDE controller on PCI bus 00 dev 48
PCI: Found IRQ 10 for device 00:09.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0xe8000000
PDC20268: ATA-66/100 forced bit set (WARNING)!!
    ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hda: ST320420A, ATA DISK drive
hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
hdc: IBM-DTLA-305040, ATA DISK drive
hdd: IC35L060AVVA07-0, ATA DISK drive
hde: WDC WD800JB-00ETA0, ATA DISK drive
hdf: WDC WD800JB-00ETA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd800-0xd807,0xdc02 on irq 10
hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=2480/255/63, UDMA(33)
hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(33)
hdd: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63, 
UDMA(33)
blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63, 
UDMA(100)
blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)
hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63, 
UDMA(100)
Partition check:
 hda: hda1 hda2
 hdc: hdc1 hdc2 hdc3
 hdd: hdd1
 hde: hde1
 hdf: hdf1
                             [snip]
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
XFS mounting filesystem ide0(3,1)
XFS mounting filesystem ide1(22,65)
XFS mounting filesystem ide1(22,1)
XFS mounting filesystem ide0(3,2)
XFS mounting filesystem ide2(33,1)
XFS mounting filesystem ide2(33,65)
hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
hdb: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdb: packet command error: error=0x00
hdb: DMA disabled
ide0: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)
#########################

and from 2.6.0-test9
#########################
Linux version 2.6.0-test9 (root@willow) (gcc version 2.96 20000731 (Red 
Hat Linux 7.3 2.96-110)) #2 Sat Nov 8 15:56:56 GMT 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000010ff0000 (usable)
 BIOS-e820: 0000000010ff0000 - 0000000010ff3000 (ACPI NVS)
 BIOS-e820: 0000000010ff3000 - 0000000011000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
271MB LOWMEM available.
On node 0 totalpages: 69616
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 65520 pages, LIFO batch:15
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Building zonelist for node : 0
Kernel command line: ro root=/dev/hdc3 noapic single
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 451.117 MHz processor.
Console: colour VGA+ 80x25
Memory: 271812k/278464k available (2117k kernel code, 5936k reserved, 
753k data, 120k init, 0k highmem)
Calibrating delay loop... 888.83 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU:     After generic identify, caps: 008021bf 808029bf 00000000 00000000
CPU:     After vendor identify, caps: 008021bf 808029bf 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: L2 Cache: 256K (32 bytes/line)
CPU:     After all inits, caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D+ Processor stepping 01
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc0e8, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0586] at 0000:00:07.0
Machine check exception polling timer started.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
SGI XFS for Linux with no debug enabled
Activating ISA DMA hang workarounds.
pty: 256 Unix98 ptys configured
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST320420A, ATA DISK drive
hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: IBM-DTLA-305040, ATA DISK drive
hdd: IC35L060AVVA07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20268: IDE controller at PCI slot 0000:00:09.0
PCI: Found IRQ 10 for device 0000:00:09.0
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0xe8000000
PDC20268: 100% native mode on irq 10
    ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD800JB-00ETA0, ATA DISK drive
hdf: WDC WD800JB-00ETA0, ATA DISK drive
hdf: set_drive_speed_status: status=0xff { Busy }
ide2 at 0xd800-0xd807,0xdc02 on irq 10
hda: max request size: 128KiB
hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63
 hda: hda1 hda2
hdc: max request size: 128KiB
hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63
 hdc: hdc1 hdc2 hdc3
hdd: max request size: 128KiB
hdd: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63
 hdd: hdd1
hde: max request size: 1024KiB
hde: status timeout: status=0xff { Busy }

hde: drive not ready for command
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
hde: status timeout: status=0xff { Busy }

hde: drive not ready for command
 hde:hde: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
hde: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev hde, sector 0
Buffer I/O error on device hde, logical block 0
end_request: I/O error, dev hde, sector 0
Buffer I/O error on device hde, logical block 0
 unable to read partition table
hdf: max request size: 1024KiB
hdf: status timeout: status=0xff { Busy }

hdf: drive not ready for command
hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
hdf: status timeout: status=0xff { Busy }

hdf: drive not ready for command
 hdf:hdf: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
hdf: status timeout: status=0xff { Busy }

PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev hdf, sector 0
Buffer I/O error on device hdf, logical block 0
end_request: I/O error, dev hdf, sector 0
Buffer I/O error on device hdf, logical block 0
 unable to read partition table
end_request: I/O error, dev hdb, sector 0
hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.12
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 
19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
ALSA device list:
  No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
UDF-fs DEBUG fs/udf/lowlevel.c:65:udf_get_last_session: 
CDROMMULTISESSION not supported: rc=-22
UDF-fs DEBUG fs/udf/super.c:1544:udf_fill_super: Multi-session=0
UDF-fs DEBUG fs/udf/super.c:531:udf_vrs: Starting at sector 16 (2048 
byte sectors)
UDF-fs: No VRS found
XFS mounting filesystem hdc3
Ending clean XFS mount for filesystem: hdc3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding 512056k swap on /dev/hdc2.  Priority:-1 extents:1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
XFS mounting filesystem hdd1
Ending clean XFS mount for filesystem: hdd1
XFS mounting filesystem hdc1
Ending clean XFS mount for filesystem: hdc1
XFS mounting filesystem hda2
Ending clean XFS mount for filesystem: hda2
hdb: DMA disabled
hda: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
end_request: I/O error, dev hde, sector 0
hde: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hde, sector 0
hde: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hde, sector 0
end_request: I/O error, dev hdf, sector 0
hdf: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hdf, sector 0
hdf: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hdf, sector 0



^ permalink raw reply	[flat|nested] 4+ messages in thread
end of thread, other threads:[~2003-11-26 22:52 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-11-08 20:25 Promise Ultra100TX2 PDC20286 broken in 2.6.0-test9 David Greaves
2003-11-26 22:50 ` David Greaves
  -- strict thread matches above, loose matches on Subject: below --
2003-11-08 16:51 David Greaves
2003-11-08 17:18 ` Bartlomiej Zolnierkiewicz

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.