HPT 1820 support?

All of lore.kernel.org
 help / color / mirror / Atom feed

* HPT 1820 support?
@ 2003-11-14  9:45 Andres Meyer
  2003-11-16 17:26 ` HPT366-driver cable detection bug Tomi Orava
  0 siblings, 1 reply; 2+ messages in thread
From: Andres Meyer @ 2003-11-14  9:45 UTC (permalink / raw)
  To: linux-ide

I just got a Highpoint 1820 controller and was wondering if there was 
anyone working on libata drivers. The binary drivers do not work with 
2.6. 199$, 8x SATA PCI-X would be ideal for this amd64 box here, but 
only with a 64bit 2.6 kernel.

Andres

^ permalink raw reply	[flat|nested] 2+ messages in thread

* HPT366-driver cable detection bug
  2003-11-14  9:45 HPT 1820 support? Andres Meyer
@ 2003-11-16 17:26 ` Tomi Orava
  0 siblings, 0 replies; 2+ messages in thread
From: Tomi Orava @ 2003-11-16 17:26 UTC (permalink / raw)
  To: linux-ide


Hi,

I'm wondering if someone would be able to figure out
the reason why the hpt366-driver under up to and
including kernel versions 2.4.23-preX detect the controller 0,
channel 1 as ATA-33 instead of ATA-66 as it should be ?

The controller in question is HPT374 with 2xSamsung 80GB
and 2xSamsung 160GB disks and the cables are identical
and for sure 80-pins versions.

The highpoint drivers seem to detect the mode properly.
However, the source code of HighTechpoint's cable detection
seems quite a bit different compared to kernels own hpt366 source code
and I'm unable to figure out what goes wrong on the latter driver ...

I'd be really happy for any answers !

Regards,
Tomi Orava

PS. Is there any information available how to interpret the
       IDE PCI-card's configuration data from the lspci-output ?



Output of /proc/ide/hpt366:
----------------------------------------------------------------------------
                            HighPoint HPT366/368/370/372/374

Controller: 0
Chipset: HPT374
--------------- Primary Channel --------------- Secondary Channel
--------------
Enabled:        yes                             yes
Cable:          ATA-66                          ATA-33

--------------- drive0 --------- drive1 ------- drive0 ---------- drive1
-------
DMA capable:    yes              no             yes               no
Mode:           UDMA             off            UDMA              off

Controller: 1
Chipset: HPT374
--------------- Primary Channel --------------- Secondary Channel
--------------
Enabled:        yes                             yes
Cable:          ATA-66                          ATA-66

--------------- drive0 --------- drive1 ------- drive0 ---------- drive1
-------
DMA capable:    no               no             no                no
Mode:           UDMA             off            UDMA              off




The dmesg shows:
---------------------------------------------------------------------
HPT374: IDE controller at PCI slot 00:0e.0
HPT374: chipset revision 7
HPT374: not 100% native mode: will probe irqs later
HPT37X: using 33MHz PCI clock
    ide2: BM-DMA at 0xb800-0xb807, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0xb808-0xb80f, BIOS settings: hdg:DMA, hdh:pio
HPT37X: using 33MHz PCI clock
    ide4: BM-DMA at 0xcc00-0xcc07, BIOS settings: hdi:DMA, hdj:pio
    ide5: BM-DMA at 0xcc08-0xcc0f, BIOS settings: hdk:DMA, hdl:pio
SiI680: IDE controller at PCI slot 00:09.0
SiI680: chipset revision 1
SiI680: not 100% native mode: will probe irqs later
SiI680: BASE CLOCK == 133
    ide6: MMIO-DMA , BIOS settings: hdm:pio, hdn:pio
    ide7: MMIO-DMA , BIOS settings: hdo:pio, hdp:pio
hda: GCR-8523B, ATAPI CD/DVD-ROM drive
hde: SAMSUNG SV8004H, ATA DISK drive
blk: queue c0470d28, I/O limit 4095Mb (mask 0xffffffff)
hdg: SAMSUNG SV8004H, ATA DISK drive
blk: queue c047117c, I/O limit 4095Mb (mask 0xffffffff)
hdi: SAMSUNG SV1604N, ATA DISK drive
blk: queue c04715d0, I/O limit 4095Mb (mask 0xffffffff)
hdk: SAMSUNG SV1604N, ATA DISK drive
blk: queue c0471a24, I/O limit 4095Mb (mask 0xffffffff)
hdm: MAXTOR 6L060J3, ATA DISK drive
blk: queue c0471e78, I/O limit 4095Mb (mask 0xffffffff)
hdo: MAXTOR 6L060J3, ATA DISK drive
blk: queue c04722cc, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xa800-0xa807,0xac02 on irq 17
ide3 at 0xb000-0xb007,0xb402 on irq 17
ide4 at 0xbc00-0xbc07,0xc002 on irq 17
ide5 at 0xc400-0xc407,0xc802 on irq 17
ide6 at 0xf885d080-0xf885d087,0xf885d08a on irq 17
ide7 at 0xf885d0c0-0xf885d0c7,0xf885d0ca on irq 17
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=155127/16/63,
UDMA(100)
hdg: attached ide-disk driver.
hdg: host protected area => 1
hdg: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=155127/16/63,
UDMA(100)
hdi: attached ide-disk driver.
hdi: host protected area => 1
hdi: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(100)
hdk: attached ide-disk driver.
hdk: host protected area => 1
hdk: 312581808 sectors (160042 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(100)
hdm: attached ide-disk driver.
hdm: host protected area => 1
hdm: 117266688 sectors (60041 MB) w/1819KiB Cache, CHS=116336/16/63,
UDMA(133)
hdo: attached ide-disk driver.
hdo: host protected area => 1
hdo: 117266688 sectors (60041 MB) w/1819KiB Cache, CHS=116336/16/63,
UDMA(133)
hda: attached ide-scsi driver.
Partition check:
 hde: hde1 hde2 hde3
 hdg: hdg1 hdg2 hdg3
 hdi: hdi1 hdi2
 hdk: hdk1 hdk2
 hdm: hdm1 hdm2
 hdo: hdo1 hdo2
-------------------------------------------------------------------------------------------------

And finally the lspci -vvv -xxx shows for the hpt374-controller the following
configuration info:

----------------------------------------------------------------------------------------------------
00:0e.0 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
	Subsystem: Triones Technologies, Inc.: Unknown device 0001
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 120 (2000ns min, 2000ns max)
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at a800 [size=8]
	Region 1: I/O ports at ac00 [size=4]
	Region 2: I/O ports at b000 [size=8]
	Region 3: I/O ports at b400 [size=4]
	Region 4: I/O ports at b800 [size=256]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 08 00 05 00 30 02 07 00 04 01 00 78 80 00
10: 01 a8 00 00 01 ac 00 00 01 b0 00 00 01 b4 00 00
20: 01 b8 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 11 01 08 08
40: 42 82 84 12 a7 4e 81 06 42 82 84 12 a7 4e 81 06
50: 05 00 00 00 05 00 00 00 1b 00 01 22 20 00 64 00
60: 01 00 22 00 00 00 00 00 00 08 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 93 00 f0 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:0e.1 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
	Subsystem: Triones Technologies, Inc.: Unknown device 0001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 120 (2000ns min, 2000ns max)
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at bc00 [size=8]
	Region 1: I/O ports at c000 [size=4]
	Region 2: I/O ports at c400 [size=8]
	Region 3: I/O ports at c800 [size=4]
	Region 4: I/O ports at cc00 [size=256]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 08 00 07 00 30 02 07 00 04 01 00 78 80 00
10: 01 bc 00 00 01 c0 00 00 01 c4 00 00 01 c8 00 00
20: 01 cc 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 11 01 08 08
40: 42 82 84 12 a7 4e 81 06 42 82 84 12 a7 4e 81 06
50: 05 00 00 00 05 00 00 00 1b 00 00 22 20 00 24 00
60: 01 00 22 00 00 00 00 00 00 08 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 96 00 f0 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

----------------------------------------------------------------------------------------------

If I use the hightechpoint's drivers the same data is little bit different:

----------------------------------------------------------------------------------------------------
00:0e.0 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
	Subsystem: Triones Technologies, Inc.: Unknown device 0001
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min, 2000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at a800 [size=8]
	Region 1: I/O ports at ac00 [size=4]
	Region 2: I/O ports at b000 [size=8]
	Region 3: I/O ports at b400 [size=4]
	Region 4: I/O ports at b800 [size=256]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 08 00 05 00 30 02 07 00 04 01 08 40 80 00
10: 01 a8 00 00 01 ac 00 00 01 b0 00 00 01 b4 00 00
20: 01 b8 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 08 08
40: 42 82 84 12 a7 4e 81 06 42 82 0c 12 a7 4e 81 06
50: 05 00 00 00 05 00 00 00 1f 00 00 21 20 00 22 00
60: 01 00 22 00 00 00 00 00 00 10 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 84 00 f0 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:0e.1 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
	Subsystem: Triones Technologies, Inc.: Unknown device 0001
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min, 2000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at bc00 [size=8]
	Region 1: I/O ports at c000 [size=4]
	Region 2: I/O ports at c400 [size=8]
	Region 3: I/O ports at c800 [size=4]
	Region 4: I/O ports at cc00 [size=256]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 08 00 05 00 30 02 07 00 04 01 08 40 80 00
10: 01 bc 00 00 01 c0 00 00 01 c4 00 00 01 c8 00 00
20: 01 cc 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 08 08
40: 42 82 84 12 a7 4e 81 06 42 82 84 12 a7 4e 81 06
50: 05 00 00 00 05 00 00 00 1b 00 00 21 20 00 22 00
60: 01 00 22 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 83 00 f0 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00





^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2003-11-16 17:26 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-11-14  9:45 HPT 1820 support? Andres Meyer
2003-11-16 17:26 ` HPT366-driver cable detection bug Tomi Orava

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.