* PROBLEM: linux-2.4.x sound module opl3sa2
@ 2004-07-22 19:13 Jack Sprat
0 siblings, 0 replies; only message in thread
From: Jack Sprat @ 2004-07-22 19:13 UTC (permalink / raw)
To: linux-kernel
I submitted this possible bug months ago to maintainer. No response for
whatever reason and the potential bug persists [or I am in error ;-) ].
-- Ron H.
1. Sound driver opl3sa2.c: Possible incorrect display of port number
2. Output from /var/log/messages; Jun 14(unpatched), Jun 18 (patched)
The suspect output is in line 2 "Search for a card at"
Jun 14 11:15:45 micron kernel: opl3sa2: Found OPL3-SA3 (YMF715 or YMF719)
Jun 14 11:15:45 micron kernel: opl3sa2: Search for a card at 0x880.
Jun 14 11:15:45 micron kernel: opl3sa2: Control I/O port 0x370 is not a
YMF7xx chipset!
Jun 18 21:43:53 micron kernel: opl3sa2: Found OPL3-SA3 (YMF715 or YMF719)
Jun 18 21:43:53 micron kernel: opl3sa2: Search for a card at 0x370.
Jun 18 21:43:53 micron kernel: opl3sa2: Control I/O port 0x370 is not a
YMF7xx chipset!
Note that 0x370 = 3*256 + 7 * 16 = 880 ; port 0x370 incorrectly
displayed as 0x880
An attempt at a patch (patch program run from /usr/src/linux):
---------------------------------
diff -durN linux-2.4.x/drivers/sound/opl3sa2.c
linux-2.4.x.new/drivers/sound/opl3sa2.c
--- linux-2.4.x/drivers/sound/opl3sa2.c 2002-08-02 20:39:44.000000000 -0400
+++ linux-2.4.x.new/drivers/sound/opl3sa2.c 2004-06-18
20:57:54.000000000 -0400
@@ -1023,7 +1023,7 @@
if(io == -1)
break;
isapnp=0;
- printk(KERN_INFO PFX "Search for a card at
0x%d.\n", io);
+ printk(KERN_INFO PFX "Search for a card at
%#x.\n", io);
/* Fall through */
}
#endif
--------------------- End patch ----------------
I suspect the remainder of this report is unnecessary but is included...
3. modules sound opl3sa2.c linux-2.4.x
4. Linux version 2.4.22-1.2197.nptl (bhcompile@daffy.perf.redhat.com)
(gcc version 3.2.3 20030422 (Red Hat Linux 3.2.3-6
)) #1 Thu Jul 1 15:29:17 EDT 2004
5. N/A
6. From modules.conf:
options opl3sa2 io=0x370 mss_io=0x530 mpu_io=0x330 irq=7 dma=0 dma2=3
7. Nothing unusual in environment
7.1 If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux micron.readyto.rumble 2.4.22-1.2197.nptl #1 Thu Jul 1 15:29:17 EDT
2004 i686 i686 i386 GNU/Linux
Gnu C 3.3.2
Gnu make 3.79.1
util-linux 2.11y
mount 2.11y
modutils 2.4.25
e2fsprogs 1.34
jfsutils 1.1.3
reiserfsprogs 3.6.8
pcmcia-cs 3.1.31
quota-tools 3.06.
PPP 2.4.1
isdn4k-utils 3.3
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 2.0.17
Net-tools 1.60
Kbd 1.08
Sh-utils 5.0
Modules Loaded lp parport autofs 8139too mii floppy sg scsi_mod
opl3sa2 mpu401 ad1848 sound soundcore keybdev mo
usedev hid input usb-uhci usbcore ext3 jbd
7.2
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 3
model name : Pentium II (Klamath)
stepping : 3
cpu MHz : 266.618
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov mmx
bogomips : 532.48
7.3
lp 8196 0 (autoclean)
parport 33952 0 (autoclean) [lp]
autofs 11156 0 (autoclean) (unused)
8139too 15560 1
mii 3736 0 [8139too]
floppy 55036 0 (autoclean)
sg 33804 0 (autoclean) (unused)
scsi_mod 107496 1 (autoclean) [sg]
opl3sa2 10000 1
mpu401 22372 0 [opl3sa2]
ad1848 25580 0 [opl3sa2]
sound 68468 1 [opl3sa2 mpu401 ad1848]
soundcore 6148 6 [sound]
keybdev 2432 0 (unused)
mousedev 5012 1
hid 22724 0 (unused)
input 5664 0 [keybdev mousedev hid]
usb-uhci 24460 0 (unused)
usbcore 73120 1 [hid usb-uhci]
ext3 65252 7
jbd 47468 7 [ext3]
7.4
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-0101 : opl3sa2
0170-0177 : ide1
01f0-01f7 : ide0
0213-0213 : isapnp read
02f8-02ff : serial(auto)
0300-0301 : mpu401
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0a79-0a79 : isapnp write
0cf8-0cff : PCI conf1
0e80-0e83 : WSS config
0e84-0e87 : MS Sound System
1000-100f : Intel Corp. 82371AB/EB/MB PIIX4 IDE
1000-1007 : ide0
1008-100f : ide1
1020-103f : Intel Corp. 82371AB/EB/MB PIIX4 USB
1020-103f : usb-uhci
1400-14ff : D-Link System Inc RTL8139 Ethernet
1400-14ff : 8139too
7000-701f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI
8000-803f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-040fdbff : System RAM
00100000-00253f65 : Kernel code
00253f66-003665a7 : Kernel data
040fdc00-040ff7ff : ACPI Tables
040ff800-040ffbff : ACPI Non-volatile Storage
040ffc00-0fffffff : System RAM
f4000000-f40000ff : D-Link System Inc RTL8139 Ethernet
f4000000-f40000ff : 8139too
f5000000-f5ffffff : PCI Bus #01
f5000000-f5ffffff : NVidia / SGS Thomson (Joint Venture) Riva128
f8000000-fbffffff : Intel Corp. 440LX/EX - 82443LX/EX Host bridge
fc000000-fcffffff : PCI Bus #01
fc000000-fcffffff : NVidia / SGS Thomson (Joint Venture) Riva128
fffe7000-ffffffff : reserved
00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev
03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f5000000-f5ffffff
Prefetchable memory behind bridge: fc000000-fcffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1000 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1020 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0f.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: NVidia / SGS Thomson (Joint Venture)
Riva128 (rev 10) (prog-if 00 [VGA])
Subsystem: Diamond Multimedia Systems Viper V330
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at fc000000 (32-bit, prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=4M]
Capabilities: [44] AGP version 1.0
Status: RQ=4 SBA- 64bit- FW- Rate=x1
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Attached devices: none
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2004-07-22 19:10 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-07-22 19:13 PROBLEM: linux-2.4.x sound module opl3sa2 Jack Sprat
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.