* PROBLEM: UHCI_HCD misses SETUP_TD (First != element) after firmware upload
@ 2005-07-26 8:14 Giedrius Liubavičius
0 siblings, 0 replies; only message in thread
From: Giedrius Liubavičius @ 2005-07-26 8:14 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1.1: Type: text/plain, Size: 727 bytes --]
Hi there,
I've got to setup D-Link DSL200i
Kernel: 2.6.11.12
Slackware 10.1.0
Aditional software user: eagle-usb.org or atm.eagle-usb.org
Problem: on my own computer, everything works fine (USB HUB 2.0,
Intel chipset, UHCI)
On this one - only when on high load
I tried to play with delays in various functions of uhci_hcd.c -
sometimes it helps
If I change uhci_result_control ending:
td= list_entry(tmp,......) to td=list_entry(head->next,..........) -
setup passes
USB device: 0x1110:0x9010 -> without firmware, 0x1110:0x900f -> with
firmware
eagle usb module uploads firmware and initiates a reset. This is
where I get to the TD selection problem.
More details on dlink.log
[-- Attachment #1.2: dlink.log --]
[-- Type: text/plain, Size: 9828 bytes --]
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:14.2: port 1 portsc 0883,00
hub 1-0:1.0: over-current change on port 1
hub 1-0:1.0: port 1, status 0101, change 0009, 12 Mb/s
uhci_hcd 0000:00:14.2: wakeup_hc
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 1-1: new full speed USB device using uhci_hcd and address 5
uhci_hcd 0000:00:14.2: uhci_result_control: failed with status 440000
[c5102240] link (051021b2) element (04548040)
0: [c4548040] link (04548080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=07d0cce0)
1: [c4548080] link (045480c0) e3 SPD Active Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=071c83e0)
2: [c45480c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
usb 1-1: device descriptor read/64, error -71
usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
DEV: registering device: ID = '1-1'
usb 1-1: hotplug
PM: Adding info for usb:1-1
bus usb: add device 1-1
bound device '1-1' to driver 'usb'
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
DEV: registering device: ID = '1-1:1.0'
usb 1-1:1.0: hotplug
PM: Adding info for usb:1-1:1.0
bus usb: add device 1-1:1.0
ueagle-atm 1-1:1.0: usb_probe_interface
ueagle-atm 1-1:1.0: usb_probe_interface - got id
usb 1-1: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X9010)
usb 1-1: reset full speed USB device using uhci_hcd and address 5
usb 1-1: [ueagle-atm] pre-firmware device, uploading firmware
CLASS: registering class device: ID = '1-1'
class_hotplug - name = 1-1
class_hotplug - hotplug() returned -19
class_hotplug - name = 1-1
CLASS: Unregistering class device. ID = '1-1'
class_hotplug - name = 1-1
device class '1-1': release.
usb 1-1: [ueagle-atm] firmware uploaded
bound device '1-1:1.0' to driver 'ueagle-atm'
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:14.2: port 1 portsc 008a,00
hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 1-1: USB disconnect, address 5
usb 1-1: usb_disable_device nuking all URBs
usb 1-1: unregistering interface 1-1:1.0
bus usb: remove device 1-1:1.0
PM: Removing info for usb:1-1:1.0
usb 1-1:1.0: hotplug
usb 1-1: unregistering device
DEV: Unregistering device. ID = '1-1'
bus usb: remove device 1-1
PM: Removing info for usb:1-1
usb 1-1: hotplug
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:14.2: port 1 portsc 0093,00
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 1-1: new full speed USB device using uhci_hcd and address 6
usb 1-1: skipped 2 descriptors after interface
usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=3
usb 1-1: default language 0x0409
usb 1-1: Product: ADSL-USB Modem
usb 1-1: SerialNumber: 000D88E54893
DEV: registering device: ID = '1-1'
usb 1-1: hotplug
PM: Adding info for usb:1-1
bus usb: add device 1-1
bound device '1-1' to driver 'usb'
uhci_hcd 0000:00:14.2: uhci_result_control: failed with status 440000
[c5102240] link (051021e2) element (04548080)
Element != First TD
0: [c4548040] link (04548080) e3 Length=7 MaxLen=7 DT0 EndPt=0 Dev=6, PID=2d(SETUP) (buf=07752620)
1: [c4548080] link (00000001) e0 IOC Stalled CRC/Timeo Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=6, PID=69(IN) (buf=00000000)
usb 1-1: can't set config #1, error -84
bus usb: remove device 1-1
PM: Removing info for usb:1-1
usb 1-1: hotplug
uhci_hcd 0000:00:14.2: port 1 portsc 0895,00
usb 1-1: new full speed USB device using uhci_hcd and address 7
uhci_hcd 0000:00:14.2: port 1 portsc 0895,00
usb 1-1: skipped 2 descriptors after interface
usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=3
usb 1-1: default language 0x0409
usb 1-1: Product: ADSL-USB Modem
usb 1-1: SerialNumber: 000D88E54893
DEV: registering device: ID = '1-1'
usb 1-1: hotplug
PM: Adding info for usb:1-1
bus usb: add device 1-1
bound device '1-1' to driver 'usb'
uhci_hcd 0000:00:14.2: uhci_result_control: failed with status 440000
[c5102240] link (051021e2) element (04548080)
Element != First TD
0: [c4548040] link (04548080) e3 Length=7 MaxLen=7 DT0 EndPt=0 Dev=7, PID=2d(SETUP) (buf=07752720)
1: [c4548080] link (00000001) e0 IOC Stalled CRC/Timeo Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=7, PID=69(IN) (buf=00000000)
usb 1-1: can't set config #1, error -84
bus usb: remove device 1-1
PM: Removing info for usb:1-1
usb 1-1: hotplug
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:14.2: port 1 portsc 0899,00
hub 1-0:1.0: port 1 enable change, status 00000101
hub 1-0:1.0: over-current change on port 1
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux mindaugas 2.6.11.12 #19 Tue Jul 26 09:23:15 EEST 2005 i686 unknown unknown GNU/Linux
Gnu C 3.3.6
Gnu make 3.80
binutils 2.15.92.0.2
util-linux 2.12p
mount 2.12p
module-init-tools 3.1
e2fsprogs 1.35
reiserfsprogs line
reiser4progs line
PPP 2.4.2
Linux C Library 2.3.5
Dynamic linker (ldd) 2.3.5
Linux C++ Library 5.0.7
Procps 3.2.3
Net-tools 1.60
Kbd 1.12
Sh-utils 5.2.1
udev 058
Modules Loaded ueagle usbatm uhci_hcd ohci_hcd ehci_hcd usbcore firmware_class atm snd_pcm_oss snd_mixer_oss snd_es18xx snd_pcm snd_page_alloc snd_opl3_lib snd_timer snd_hwdep snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore intel_agp agpgart
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR+ <PERR-
Latency: 64
Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 40000000-400fffff
Prefetchable memory behind bridge: 41000000-41ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:0a.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05)
Subsystem: Compaq Computer Corporation NC3161 Fast Ethernet NIC (embedded, WOL)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 42100000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at 2000 [size=32]
Region 2: Memory at 42000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:14.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 2040 [size=16]
00:14.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 2020 [size=32]
00:14.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Pro Turbo AGP 2X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 41000000 (32-bit, prefetchable) [size=16M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at 40000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
[-- Attachment #1.3: giedrius.vcf --]
[-- Type: text/x-vcard, Size: 355 bytes --]
begin:vcard
fn;quoted-printable:Giedrius Liubavi=C4=8Dius
n;quoted-printable:Liubavi=C4=8Dius;Giedrius
org:;Technologijos fak.
adr;quoted-printable:;;;=C5=A0iauliai;;;Lietuva
email;internet:giedrius@galva.su.lt
title:Studentas, R3
tel;work:+37041595737
tel;cell:+37068450498
x-mozilla-html:TRUE
url:http://galva.su.lt
version:2.1
end:vcard
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 256 bytes --]
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2005-07-26 8:17 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-07-26 8:14 PROBLEM: UHCI_HCD misses SETUP_TD (First != element) after firmware upload Giedrius Liubavičius
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.