* Compiling uClibc with MIPS SDE6
@ 2005-08-04 9:16 ` colin
0 siblings, 0 replies; 5+ messages in thread
From: colin @ 2005-08-04 9:16 UTC (permalink / raw)
To: linux-mips
Hi there,
I encounter a problem when compiling uClibc with SDE6. If compiling with
debug information enabled, the output executable file of busybox is about
the same with the one that is compiled with SDE5, but uClibc libraries are
over 10 times the size of the ones that are compiled with SDE5. I am
wondering if it is because GCC 3.4.4 of SDE6 has changed some parameters
setting?
Regards,
Colin
^ permalink raw reply [flat|nested] 5+ messages in thread
* Compiling uClibc with MIPS SDE6
@ 2005-08-04 9:16 ` colin
0 siblings, 0 replies; 5+ messages in thread
From: colin @ 2005-08-04 9:16 UTC (permalink / raw)
To: linux-mips
Hi there,
I encounter a problem when compiling uClibc with SDE6. If compiling with
debug information enabled, the output executable file of busybox is about
the same with the one that is compiled with SDE5, but uClibc libraries are
over 10 times the size of the ones that are compiled with SDE5. I am
wondering if it is because GCC 3.4.4 of SDE6 has changed some parameters
setting?
Regards,
Colin
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Compiling uClibc with MIPS SDE6
2005-08-04 9:16 ` colin
(?)
@ 2005-08-04 11:12 ` Nigel Stephens
2005-08-04 12:09 ` colin
-1 siblings, 1 reply; 5+ messages in thread
From: Nigel Stephens @ 2005-08-04 11:12 UTC (permalink / raw)
To: colin; +Cc: linux-mips
colin wrote:
>Hi there,
>I encounter a problem when compiling uClibc with SDE6. If compiling with
>debug information enabled, the output executable file of busybox is about
>the same with the one that is compiled with SDE5, but uClibc libraries are
>over 10 times the size of the ones that are compiled with SDE5. I am
>wondering if it is because GCC 3.4.4 of SDE6 has changed some parameters
>setting?
>
>
>
SDE 6 uses Dwarf-2 debug data, whereas SDE 5 used Stabs. That may
explain the difference.
Nigel
--
Nigel Stephens Mailto:nigel@mips.com
_ _ ____ ___ MIPS Technologies Phone.: +44 1223 706200
|\ /|||___)(___ The Fruit Farm Direct: +44 1223 706207
| \/ ||| ____) Ely Road, Chittering Fax...: +44 1223 706250
TECHNOLOGIES UK Cambridge CB5 9PH Cell..: +44 7976 686470
England http://www.mips.com
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: Compiling uClibc with MIPS SDE6
@ 2005-08-04 12:09 ` colin
0 siblings, 0 replies; 5+ messages in thread
From: colin @ 2005-08-04 12:09 UTC (permalink / raw)
To: Nigel Stephens; +Cc: linux-mips
Hi Nigel,
I had already noticed this difference.
But why the application with debug information is not so big, whereas the
libraries are?
And the SDE 6 document says that using -gstabs flag can make it compile with
STABS debug format.
I replaced -g3 with -gstabs flag when compiling uClibc, but it cannot
compile successfully.
Regards,
Colin
----- Original Message -----
From: "Nigel Stephens" <nigel@mips.com>
To: "colin" <colin@realtek.com.tw>
Cc: <linux-mips@linux-mips.org>
Sent: Thursday, August 04, 2005 7:12 PM
Subject: Re: Compiling uClibc with MIPS SDE6
>
>
> colin wrote:
>
> >Hi there,
> >I encounter a problem when compiling uClibc with SDE6. If compiling with
> >debug information enabled, the output executable file of busybox is about
> >the same with the one that is compiled with SDE5, but uClibc libraries
are
> >over 10 times the size of the ones that are compiled with SDE5. I am
> >wondering if it is because GCC 3.4.4 of SDE6 has changed some parameters
> >setting?
> >
> >
> >
>
> SDE 6 uses Dwarf-2 debug data, whereas SDE 5 used Stabs. That may
> explain the difference.
>
> Nigel
>
> --
> Nigel Stephens Mailto:nigel@mips.com
> _ _ ____ ___ MIPS Technologies Phone.: +44 1223 706200
> |\ /|||___)(___ The Fruit Farm Direct: +44 1223 706207
> | \/ ||| ____) Ely Road, Chittering Fax...: +44 1223 706250
> TECHNOLOGIES UK Cambridge CB5 9PH Cell..: +44 7976 686470
> England http://www.mips.com
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Compiling uClibc with MIPS SDE6
@ 2005-08-04 12:09 ` colin
0 siblings, 0 replies; 5+ messages in thread
From: colin @ 2005-08-04 12:09 UTC (permalink / raw)
To: Nigel Stephens; +Cc: linux-mips
Hi Nigel,
I had already noticed this difference.
But why the application with debug information is not so big, whereas the
libraries are?
And the SDE 6 document says that using -gstabs flag can make it compile with
STABS debug format.
I replaced -g3 with -gstabs flag when compiling uClibc, but it cannot
compile successfully.
Regards,
Colin
----- Original Message -----
From: "Nigel Stephens" <nigel@mips.com>
To: "colin" <colin@realtek.com.tw>
Cc: <linux-mips@linux-mips.org>
Sent: Thursday, August 04, 2005 7:12 PM
Subject: Re: Compiling uClibc with MIPS SDE6
>
>
> colin wrote:
>
> >Hi there,
> >I encounter a problem when compiling uClibc with SDE6. If compiling with
> >debug information enabled, the output executable file of busybox is about
> >the same with the one that is compiled with SDE5, but uClibc libraries
are
> >over 10 times the size of the ones that are compiled with SDE5. I am
> >wondering if it is because GCC 3.4.4 of SDE6 has changed some parameters
> >setting?
> >
> >
> >
>
> SDE 6 uses Dwarf-2 debug data, whereas SDE 5 used Stabs. That may
> explain the difference.
>
> Nigel
>
> --
> Nigel Stephens Mailto:nigel@mips.com
> _ _ ____ ___ MIPS Technologies Phone.: +44 1223 706200
> |\ /|||___)(___ The Fruit Farm Direct: +44 1223 706207
> | \/ ||| ____) Ely Road, Chittering Fax...: +44 1223 706250
> TECHNOLOGIES UK Cambridge CB5 9PH Cell..: +44 7976 686470
> England http://www.mips.com
>
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2005-08-04 16:10 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-08-04 9:16 Compiling uClibc with MIPS SDE6 colin
2005-08-04 9:16 ` colin
2005-08-04 11:12 ` Nigel Stephens
2005-08-04 12:09 ` colin
2005-08-04 12:09 ` colin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.