Problems getting linux-2.4.31 to detect logical drive on megaraid ATA card.

Problems getting linux-2.4.31 to detect logical drive on megaraid ATA card.

[Matthew Schumacher]

List,

I have a problem I just can't seem to figure out. linux 2.4.27 can see
the logical drive just fine:

megaraid: v2.10.3 (Release Date: Thu Apr  8 16:16:05 EDT 2004)
megaraid: found 0x101e:0x1960:bus 0:slot 3:func 0
scsi0:Found MegaRAID controller at 0xf89c3000, IRQ:17
megaraid: [6.62:1.03] detected 1 logical drives.
megaraid: supports extended CDBs.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: channel[2] is raid.
megaraid: channel[3] is raid.
scsi0 : LSI Logic MegaRAID 6.62 254 commands 16 targs 7 chans 7 luns
scsi0: scanning scsi channel 0 for logical drives.
  Vendor: MegaRAID  Model: LD 0 RAID1  114G  Rev: 6.62
  Type:   Direct-Access                      ANSI SCSI revision: 02
scsi0: scanning scsi channel 1 for logical drives.
scsi0: scanning scsi channel 2 for logical drives.
scsi0: scanning scsi channel 4 [P0] for physical devices.
scsi0: scanning scsi channel 5 [P1] for physical devices.
scsi0: scanning scsi channel 6 [P2] for physical devices.
scsi0: scanning scsi channel 7 [P3] for physical devices.
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 234348544 512-byte hdwr sectors (119986 MB)
Partition check:
 sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 >
usb.c: registered new driver usbdevfs

However linux-2.4.31 doesn't see it:

SCSI subsystem driver Revision: 1.00
megaraid: v2.10.8.2 (Release Date: Mon Jul 26 12:15:51 EDT 2004)
megaraid: found 0x101e:0x1960:bus 0:slot 3:func 0
scsi0:Found MegaRAID controller at 0xf8855000, IRQ:15
megaraid: [6.62:1.03] detected 1 logical drives.
megaraid: supports extended CDBs.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: channel[2] is raid.
megaraid: channel[3] is raid.
scsi0 : LSI Logic MegaRAID 6.62 254 commands 16 targs 7 chans 7 luns
scsi0: scanning scsi channel 0 for logical drives.
scsi0: scanning scsi channel 1 for logical drives.
scsi0: scanning scsi channel 2 for logical drives.
scsi0: scanning scsi channel 3 for logical drives.
scsi0: scanning scsi channel 4 [P0] for physical devices.
scsi0: scanning scsi channel 5 [P1] for physical devices.
scsi0: scanning scsi channel 6 [P2] for physical devices.
scsi0: scanning scsi channel 7 [P3] for physical devices.

The card is a LSI ATA megaraid controller sold by dell as a CERT card.
I have the latest firmware on it.

At this point I'm not sure what to do.  Any ideas on how to make the
newer megaraid driver see the logical drive?

schu