* [lm-sensors] Loaded Modules but 'No sensors found'
@ 2006-01-11 4:37 embree
2006-01-13 3:58 ` Mark M. Hoffman
` (4 more replies)
0 siblings, 5 replies; 6+ messages in thread
From: embree @ 2006-01-11 4:37 UTC (permalink / raw)
To: lm-sensors
I have searched in vain for a solution to my problem I was going to submit a support ticket but your website said to submit here instead. so here it goes.
I've followed all instructions I could find. It seems as if all modules get detected and load fine. Yet running 'sensors returns 'No sensors found'. Any thoughts?????
Kernel 2.6.14.5 (with gentoo patches)(SMP Opteron 64 bit)
lm_sensors 2.9.2
Motherboard Tyan Tiger K8W S2875 Bios 3.02
Here's all the relavant output I can think of. btw this is will all i2c debugging kernel options on)
lspci
Code:
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System Controller (rev 13)
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev 13)
00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV35 [GeForce FX 5900XT] (rev a1)
02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
02:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
02:03.0 Ethernet controller: Intel Corporation 82541EI Gigabit Ethernet Controller (Copper)
02:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
02:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
02:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
02:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 62)
lsmod
Code:
Module Size Used by
nfs 211304 1
lockd 70096 2 nfs
sunrpc 162632 3 nfs,lockd
w83627hf 30480 0
hwmon_vid 3008 1 w83627hf
hwmon 3784 1 w83627hf
eeprom 8720 0
i2c_isa 7040 1 w83627hf
snd_seq 62080 0
snd_seq_device 10192 1 snd_seq
pwc 52492 0
videodev 12416 1 pwc
snd_intel8x0 37160 3
snd_ac97_codec 108568 1 snd_intel8x0
snd_ac97_bus 3008 1 snd_ac97_codec
snd_pcm 101000 3 snd_intel8x0,snd_ac97_codec
snd_timer 27208 3 snd_seq,snd_pcm
snd 63072 10 snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 12128 1 snd
snd_page_alloc 12240 2 snd_intel8x0,snd_pcm
i2c_amd756 8900 0
i2c_amd8111 7040 0
nvidia 4857712 12
sbp2 25860 0
ohci1394 35020 0
ieee1394 108664 2 sbp2,ohci1394
usb_storage 70400 0
usbhid 40032 0
Relavent dmesg
Code:
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005
i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered
amd756_smbus 0000:00:07.3: SMBREV = 0x5
amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0
i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered
ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18
intel8x0_measure_ac97_clock: measured 50753 usecs
intel8x0: clocking to 48000
Linux video capture interface: v1.00
pwc Philips webcam module version 9.0.2-unofficial loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
pwc Logitech QuickCam 4000 Pro USB webcam detected.
pwc Registered as /dev/video0.
usbcore: registered new driver Philips webcam
e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex
i2c_adapter i2c-9191: ISA main adapter registered
i2c-core: driver [eeprom] registered
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56
i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
i2c_adapter i2c-1: SMBus protocol success!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
i2c_adapter i2c-1: SMBus protocol success!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
i2c_adapter i2c-1: SMBus Protocol error (no response)!
i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
i2c_adapter i2c-9191: Driver w83627hf registered
Relevant /var/log/messages
Code:
Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
Jan 9 17:27:23 Gentoo64 NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005
Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered
Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: SMBREV = 0x5
Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0
Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered
Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18
Jan 9 17:27:23 Gentoo64 intel8x0_measure_ac97_clock: measured 50753 usecs
Jan 9 17:27:23 Gentoo64 intel8x0: clocking to 48000
Jan 9 17:27:23 Gentoo64 Linux video capture interface: v1.00
Jan 9 17:27:23 Gentoo64 pwc Philips webcam module version 9.0.2-unofficial loaded.
Jan 9 17:27:23 Gentoo64 pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
Jan 9 17:27:23 Gentoo64 pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
Jan 9 17:27:23 Gentoo64 pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
Jan 9 17:27:23 Gentoo64 pwc Logitech QuickCam 4000 Pro USB webcam detected.
Jan 9 17:27:23 Gentoo64 pwc Registered as /dev/video0.
Jan 9 17:27:23 Gentoo64 usbcore: registered new driver Philips webcam
Jan 9 17:27:23 Gentoo64 rc-scripts: Configuration not set for eth0 - assuming dhcp
Jan 9 17:27:23 Gentoo64 e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: ISA main adapter registered
Jan 9 17:27:29 Gentoo64 i2c-core: driver [eeprom] registered
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: Driver w83627hf registered
I'm lost I don't know what else to try. Any suggestion would be more than appreciated.
PS MY bios allow both ACPI version 1 or 2 I've tried both and got the same results.
Thanks in advance!!!!!!!!!
^ permalink raw reply [flat|nested] 6+ messages in thread
* [lm-sensors] Loaded Modules but 'No sensors found'
2006-01-11 4:37 [lm-sensors] Loaded Modules but 'No sensors found' embree
@ 2006-01-13 3:58 ` Mark M. Hoffman
2006-01-13 19:43 ` Kevin Embree
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Mark M. Hoffman @ 2006-01-13 3:58 UTC (permalink / raw)
To: lm-sensors
Hi:
* embree at speakeasy.net <embree at speakeasy.net> [2006-01-11 04:37:59 +0000]:
> I have searched in vain for a solution to my problem I was going to submit
> a support ticket but your website said to submit here instead. so here it
> goes.
>
> I've followed all instructions I could find. It seems as if all modules get
> detected and load fine. Yet running 'sensors returns 'No sensors found'. Any
> thoughts?????
I guess: unload eeprom, i2c-amd756, and i2c-amd8111; then try again. Your
hardware monitor (w83627hf or some such) is probably visible through i2c-isa
alone. If that doesn't work, please send the output from sensors-detect.
Anyway, it looks like i2c-amd756 and/or i2c-amd8111 is hosed up. I'm not sure
why. Can anyone else jump in on that?
> Kernel 2.6.14.5 (with gentoo patches)(SMP Opteron 64 bit)
> lm_sensors 2.9.2
> Motherboard Tyan Tiger K8W S2875 Bios 3.02
>
> Here's all the relavant output I can think of. btw this is will all i2c debugging kernel options on)
>
> lspci
> Code:
> 00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System Controller (rev 13)
> 00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev 13)
> 00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
> 00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
> 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
> 00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
> 00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
> 00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03)
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
> 01:00.0 VGA compatible controller: nVidia Corporation NV35 [GeForce FX 5900XT] (rev a1)
> 02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
> 02:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
> 02:03.0 Ethernet controller: Intel Corporation 82541EI Gigabit Ethernet Controller (Copper)
> 02:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
> 02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
> 02:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
> 02:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
> 02:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 62)
>
>
> lsmod
>
> Code:
> Module Size Used by
> nfs 211304 1
> lockd 70096 2 nfs
> sunrpc 162632 3 nfs,lockd
> w83627hf 30480 0
> hwmon_vid 3008 1 w83627hf
> hwmon 3784 1 w83627hf
> eeprom 8720 0
> i2c_isa 7040 1 w83627hf
> snd_seq 62080 0
> snd_seq_device 10192 1 snd_seq
> pwc 52492 0
> videodev 12416 1 pwc
> snd_intel8x0 37160 3
> snd_ac97_codec 108568 1 snd_intel8x0
> snd_ac97_bus 3008 1 snd_ac97_codec
> snd_pcm 101000 3 snd_intel8x0,snd_ac97_codec
> snd_timer 27208 3 snd_seq,snd_pcm
> snd 63072 10 snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
> soundcore 12128 1 snd
> snd_page_alloc 12240 2 snd_intel8x0,snd_pcm
> i2c_amd756 8900 0
> i2c_amd8111 7040 0
> nvidia 4857712 12
> sbp2 25860 0
> ohci1394 35020 0
> ieee1394 108664 2 sbp2,ohci1394
> usb_storage 70400 0
> usbhid 40032 0
>
>
> Relavent dmesg
> Code:
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
> NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005
> i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered
> amd756_smbus 0000:00:07.3: SMBREV = 0x5
> amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0
> i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered
> ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18
> intel8x0_measure_ac97_clock: measured 50753 usecs
> intel8x0: clocking to 48000
> Linux video capture interface: v1.00
> pwc Philips webcam module version 9.0.2-unofficial loaded.
> pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
> pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
> pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
> pwc Logitech QuickCam 4000 Pro USB webcam detected.
> pwc Registered as /dev/video0.
> usbcore: registered new driver Philips webcam
> e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex
> i2c_adapter i2c-9191: ISA main adapter registered
> i2c-core: driver [eeprom] registered
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56
> i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
> i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
> i2c_adapter i2c-1: SMBus protocol success!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
> i2c_adapter i2c-1: SMBus protocol success!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
> i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
> i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
> i2c_adapter i2c-1: SMBus Protocol error (no response)!
> i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
> i2c_adapter i2c-9191: Driver w83627hf registered
>
> Relevant /var/log/messages
> Code:
> Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
> Jan 9 17:27:23 Gentoo64 NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005
> Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered
> Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: SMBREV = 0x5
> Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0
> Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered
> Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18
> Jan 9 17:27:23 Gentoo64 intel8x0_measure_ac97_clock: measured 50753 usecs
> Jan 9 17:27:23 Gentoo64 intel8x0: clocking to 48000
> Jan 9 17:27:23 Gentoo64 Linux video capture interface: v1.00
> Jan 9 17:27:23 Gentoo64 pwc Philips webcam module version 9.0.2-unofficial loaded.
> Jan 9 17:27:23 Gentoo64 pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
> Jan 9 17:27:23 Gentoo64 pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
> Jan 9 17:27:23 Gentoo64 pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
> Jan 9 17:27:23 Gentoo64 pwc Logitech QuickCam 4000 Pro USB webcam detected.
> Jan 9 17:27:23 Gentoo64 pwc Registered as /dev/video0.
> Jan 9 17:27:23 Gentoo64 usbcore: registered new driver Philips webcam
> Jan 9 17:27:23 Gentoo64 rc-scripts: Configuration not set for eth0 - assuming dhcp
> Jan 9 17:27:23 Gentoo64 e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: ISA main adapter registered
> Jan 9 17:27:29 Gentoo64 i2c-core: driver [eeprom] registered
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
> Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: Driver w83627hf registered
>
>
> I'm lost I don't know what else to try. Any suggestion would be more than appreciated.
>
> PS MY bios allow both ACPI version 1 or 2 I've tried both and got the same results.
>
> Thanks in advance!!!!!!!!!
Regards,
--
Mark M. Hoffman
mhoffman at lightlink.com
^ permalink raw reply [flat|nested] 6+ messages in thread
* [lm-sensors] Loaded Modules but 'No sensors found'
2006-01-11 4:37 [lm-sensors] Loaded Modules but 'No sensors found' embree
2006-01-13 3:58 ` Mark M. Hoffman
@ 2006-01-13 19:43 ` Kevin Embree
2006-01-13 22:22 ` Jean Delvare
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Kevin Embree @ 2006-01-13 19:43 UTC (permalink / raw)
To: lm-sensors
Mark M. Hoffman wrote:
>Hi:
>
>* embree at speakeasy.net <embree at speakeasy.net> [2006-01-11 04:37:59 +0000]:
>
>
>>I have searched in vain for a solution to my problem I was going to submit
>>a support ticket but your website said to submit here instead. so here it
>>goes.
>>
>>I've followed all instructions I could find. It seems as if all modules get
>>detected and load fine. Yet running 'sensors returns 'No sensors found'. Any
>>thoughts?????
>>
>>
>
>I guess: unload eeprom, i2c-amd756, and i2c-amd8111; then try again. Your
>hardware monitor (w83627hf or some such) is probably visible through i2c-isa
>alone. If that doesn't work, please send the output from sensors-detect.
>
>Anyway, it looks like i2c-amd756 and/or i2c-amd8111 is hosed up. I'm not sure
>why. Can anyone else jump in on that?
>
>
I haven't had the chance yet to try this but I did try a new kernel and
that worked.
I tried kernel 2.6.15 w/ gentoo and ck patches. I will try you above
suggestion and also vanilla kernel 2.6.15 for comparison.
Thanks for your help!
>
>
>>Kernel 2.6.14.5 (with gentoo patches)(SMP Opteron 64 bit)
>>lm_sensors 2.9.2
>>Motherboard Tyan Tiger K8W S2875 Bios 3.02
>>
>>Here's all the relavant output I can think of. btw this is will all i2c debugging kernel options on)
>>
>>lspci
>>Code:
>>00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System Controller (rev 13)
>>00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev 13)
>>00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
>>00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
>>00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
>>00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
>>00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
>>00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03)
>>00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
>>00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
>>00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
>>00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
>>01:00.0 VGA compatible controller: nVidia Corporation NV35 [GeForce FX 5900XT] (rev a1)
>>02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
>>02:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
>>02:03.0 Ethernet controller: Intel Corporation 82541EI Gigabit Ethernet Controller (Copper)
>>02:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
>>02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
>>02:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
>>02:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
>>02:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 62)
>>
>>
>>lsmod
>>
>>Code:
>>Module Size Used by
>>nfs 211304 1
>>lockd 70096 2 nfs
>>sunrpc 162632 3 nfs,lockd
>>w83627hf 30480 0
>>hwmon_vid 3008 1 w83627hf
>>hwmon 3784 1 w83627hf
>>eeprom 8720 0
>>i2c_isa 7040 1 w83627hf
>>snd_seq 62080 0
>>snd_seq_device 10192 1 snd_seq
>>pwc 52492 0
>>videodev 12416 1 pwc
>>snd_intel8x0 37160 3
>>snd_ac97_codec 108568 1 snd_intel8x0
>>snd_ac97_bus 3008 1 snd_ac97_codec
>>snd_pcm 101000 3 snd_intel8x0,snd_ac97_codec
>>snd_timer 27208 3 snd_seq,snd_pcm
>>snd 63072 10 snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
>>soundcore 12128 1 snd
>>snd_page_alloc 12240 2 snd_intel8x0,snd_pcm
>>i2c_amd756 8900 0
>>i2c_amd8111 7040 0
>>nvidia 4857712 12
>>sbp2 25860 0
>>ohci1394 35020 0
>>ieee1394 108664 2 sbp2,ohci1394
>>usb_storage 70400 0
>>usbhid 40032 0
>>
>>
>>Relavent dmesg
>>Code:
>>ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
>>NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005
>>i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered
>>amd756_smbus 0000:00:07.3: SMBREV = 0x5
>>amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0
>>i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered
>>ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18
>>intel8x0_measure_ac97_clock: measured 50753 usecs
>>intel8x0: clocking to 48000
>>Linux video capture interface: v1.00
>>pwc Philips webcam module version 9.0.2-unofficial loaded.
>>pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
>>pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
>>pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
>>pwc Logitech QuickCam 4000 Pro USB webcam detected.
>>pwc Registered as /dev/video0.
>>usbcore: registered new driver Philips webcam
>>e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex
>>i2c_adapter i2c-9191: ISA main adapter registered
>>i2c-core: driver [eeprom] registered
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56
>>i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
>>i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
>>i2c_adapter i2c-1: SMBus protocol success!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
>>i2c_adapter i2c-1: SMBus protocol success!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
>>i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
>>i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
>>i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
>>i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
>>i2c_adapter i2c-9191: Driver w83627hf registered
>>
>>Relevant /var/log/messages
>>Code:
>>Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
>>Jan 9 17:27:23 Gentoo64 NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:58:07 PST 2005
>>Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-0: adapter [SMBus2 AMD8111 adapter at c480] registered
>>Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: SMBREV = 0x5
>>Jan 9 17:27:23 Gentoo64 amd756_smbus 0000:00:07.3: AMD756_smba = 0x10E0
>>Jan 9 17:27:23 Gentoo64 i2c_adapter i2c-1: adapter [SMBus AMD8111 adapter at 10e0] registered
>>Jan 9 17:27:23 Gentoo64 ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18
>>Jan 9 17:27:23 Gentoo64 intel8x0_measure_ac97_clock: measured 50753 usecs
>>Jan 9 17:27:23 Gentoo64 intel8x0: clocking to 48000
>>Jan 9 17:27:23 Gentoo64 Linux video capture interface: v1.00
>>Jan 9 17:27:23 Gentoo64 pwc Philips webcam module version 9.0.2-unofficial loaded.
>>Jan 9 17:27:23 Gentoo64 pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
>>Jan 9 17:27:23 Gentoo64 pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
>>Jan 9 17:27:23 Gentoo64 pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
>>Jan 9 17:27:23 Gentoo64 pwc Logitech QuickCam 4000 Pro USB webcam detected.
>>Jan 9 17:27:23 Gentoo64 pwc Registered as /dev/video0.
>>Jan 9 17:27:23 Gentoo64 usbcore: registered new driver Philips webcam
>>Jan 9 17:27:23 Gentoo64 rc-scripts: Configuration not set for eth0 - assuming dhcp
>>Jan 9 17:27:23 Gentoo64 e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: ISA main adapter registered
>>Jan 9 17:27:29 Gentoo64 i2c-core: driver [eeprom] registered
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x50
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x51
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x52
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x53
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x54
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x55
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x56
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-0: found normal entry for adapter 0, addr 0x57
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus protocol success!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: SMBus Protocol error (no response)!
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
>>Jan 9 17:27:29 Gentoo64 i2c_adapter i2c-9191: Driver w83627hf registered
>>
>>
>>I'm lost I don't know what else to try. Any suggestion would be more than appreciated.
>>
>>PS MY bios allow both ACPI version 1 or 2 I've tried both and got the same results.
>>
>>Thanks in advance!!!!!!!!!
>>
>>
>
>Regards,
>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [lm-sensors] Loaded Modules but 'No sensors found'
2006-01-11 4:37 [lm-sensors] Loaded Modules but 'No sensors found' embree
2006-01-13 3:58 ` Mark M. Hoffman
2006-01-13 19:43 ` Kevin Embree
@ 2006-01-13 22:22 ` Jean Delvare
2006-01-13 22:29 ` Jean Delvare
2006-01-14 4:09 ` Mark M. Hoffman
4 siblings, 0 replies; 6+ messages in thread
From: Jean Delvare @ 2006-01-13 22:22 UTC (permalink / raw)
To: lm-sensors
Hi Mark,
> Anyway, it looks like i2c-amd756 and/or i2c-amd8111 is hosed up. I'm not sure
> why. Can anyone else jump in on that?
If you refer to these log messages:
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
> > i2c_adapter i2c-1: Transaction (pre): GS\004, GE\000, ADD\0a0, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a0, DAT\002
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x51
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
> > i2c_adapter i2c-1: SMBus protocol success!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a2, DAT\002
> > i2c_adapter i2c-1: SMBus protocol success!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a2, DAT\002
> > i2c_adapter i2c-1: client [eeprom] registered with bus id 1-0051
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x52
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a4, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a4, DAT\002
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x53
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a6, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a6, DAT\002
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x54
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0a8, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0a8, DAT\002
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x55
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0aa, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0aa, DAT\002
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x56
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ac, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ac, DAT\002
> > i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x57
> > i2c_adapter i2c-1: Transaction (pre): GS\000, GE\000, ADD\0ae, DAT\002
> > i2c_adapter i2c-1: SMBus Protocol error (no response)!
> > i2c_adapter i2c-1: Transaction (post): GS\000, GE\000, ADD\0ae, DAT\002
I don't think there's anything wrong. Kevin said:
> > Here's all the relavant output I can think of. btw this is will
> > all i2c debugging kernel options on)
Bus drivers tend to be pretty verbose during probing in debugging mode,
because missed probes are actually non-acked SMBus transactions, so
they are seen as errors by the master. Nothing to be worried about.
--
Jean Delvare
^ permalink raw reply [flat|nested] 6+ messages in thread
* [lm-sensors] Loaded Modules but 'No sensors found'
2006-01-11 4:37 [lm-sensors] Loaded Modules but 'No sensors found' embree
` (2 preceding siblings ...)
2006-01-13 22:22 ` Jean Delvare
@ 2006-01-13 22:29 ` Jean Delvare
2006-01-14 4:09 ` Mark M. Hoffman
4 siblings, 0 replies; 6+ messages in thread
From: Jean Delvare @ 2006-01-13 22:29 UTC (permalink / raw)
To: lm-sensors
Hi Kevin,
> > > I've followed all instructions I could find. It seems as if all modules get
> > > detected and load fine. Yet running 'sensors returns 'No sensors found'. Any
> > > thoughts?????
> >
> > I guess: unload eeprom, i2c-amd756, and i2c-amd8111; then try again. Your
> > hardware monitor (w83627hf or some such) is probably visible through i2c-isa
> > alone. If that doesn't work, please send the output from sensors-detect.
>
> I haven't had the chance yet to try this but I did try a new kernel and
> that worked.
> I tried kernel 2.6.15 w/ gentoo and ck patches. I will try you above
> suggestion and also vanilla kernel 2.6.15 for comparison.
My own guess is the conflict between PNPACPI and the w83627hf driver,
which is known to have affected the Linux kernels from 2.6.10 to 2.6.14:
http://bugzilla.kernel.org/show_bug.cgi?id@14
If I am right, the only way to get it to work on a 2.6.14.x kernel
would be to disable the PNPACPI configuration option (pnpacpi=off on
the bootloader command line will do too.)
2.6.15 vanilla should work just fine too.
Hope that helps,
--
Jean Delvare
^ permalink raw reply [flat|nested] 6+ messages in thread
* [lm-sensors] Loaded Modules but 'No sensors found'
2006-01-11 4:37 [lm-sensors] Loaded Modules but 'No sensors found' embree
` (3 preceding siblings ...)
2006-01-13 22:29 ` Jean Delvare
@ 2006-01-14 4:09 ` Mark M. Hoffman
4 siblings, 0 replies; 6+ messages in thread
From: Mark M. Hoffman @ 2006-01-14 4:09 UTC (permalink / raw)
To: lm-sensors
Hi Jean, Kevin:
Kevin wrote:
> > > > I've followed all instructions I could find. It seems as if all modules get
> > > > detected and load fine. Yet running 'sensors returns 'No sensors found'. Any
> > > > thoughts?????
Mark wrote:
> > > I guess: unload eeprom, i2c-amd756, and i2c-amd8111; then try again. Your
> > > hardware monitor (w83627hf or some such) is probably visible through i2c-isa
> > > alone. If that doesn't work, please send the output from sensors-detect.
Kevin wrote:
> > I haven't had the chance yet to try this but I did try a new kernel and
> > that worked.
> > I tried kernel 2.6.15 w/ gentoo and ck patches. I will try you above
> > suggestion and also vanilla kernel 2.6.15 for comparison.
* Jean Delvare <khali at linux-fr.org> [2006-01-13 23:29:35 +0100]:
> My own guess is the conflict between PNPACPI and the w83627hf driver,
> which is known to have affected the Linux kernels from 2.6.10 to 2.6.14:
>
> http://bugzilla.kernel.org/show_bug.cgi?id@14
Oops, I forgot about that one. You're probably right.
Regards,
--
Mark M. Hoffman
mhoffman at lightlink.com
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2006-01-14 4:09 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-01-11 4:37 [lm-sensors] Loaded Modules but 'No sensors found' embree
2006-01-13 3:58 ` Mark M. Hoffman
2006-01-13 19:43 ` Kevin Embree
2006-01-13 22:22 ` Jean Delvare
2006-01-13 22:29 ` Jean Delvare
2006-01-14 4:09 ` Mark M. Hoffman
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.