* [PATCH 4/6] sata_sil24: rename PORT_PRB to PORT_LRAM and add PORT_LRAM_SLOT_SZ
2006-05-19 15:38 [PATCHSET 02/03] prep LLDDs for hotplug support, take 2 Tejun Heo
@ 2006-05-19 15:38 ` Tejun Heo
2006-05-19 15:38 ` [PATCH 6/6] sata_sil24: kill ops->tf_read() and use ata_std_noop_check_status() Tejun Heo
` (4 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Tejun Heo @ 2006-05-19 15:38 UTC (permalink / raw)
To: jgarzik, mlord, albertcc, alan, axboe, forrest.zhao, linux-ide; +Cc: Tejun Heo
PORT_PRB is a misnomer as the area also contains other stuff. Rename
it to PORT_LRAM and add PORT_LRAM_SLOT_SZ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/sata_sil24.c | 6 ++++--
1 files changed, 4 insertions(+), 2 deletions(-)
629710d0712433cf74b67881ba62dd398d87e3eb
diff --git a/drivers/scsi/sata_sil24.c b/drivers/scsi/sata_sil24.c
index 26d7c54..a39e8d0 100644
--- a/drivers/scsi/sata_sil24.c
+++ b/drivers/scsi/sata_sil24.c
@@ -98,7 +98,9 @@ enum {
* (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2)
*/
PORT_REGS_SIZE = 0x2000,
- PORT_PRB = 0x0000, /* (32 bytes PRB + 16 bytes SGEs * 6) * 31 (3968 bytes) */
+
+ PORT_LRAM = 0x0000, /* 31 LRAM slots and PM regs */
+ PORT_LRAM_SLOT_SZ = 0x0080, /* 32 bytes PRB + 2 SGE, ACT... */
PORT_PM = 0x0f80, /* 8 bytes PM * 16 (128 bytes) */
/* 32 bit regs */
@@ -1103,7 +1105,7 @@ static int sil24_init_one(struct pci_dev
void __iomem *port = port_base + i * PORT_REGS_SIZE;
unsigned long portu = (unsigned long)port;
- probe_ent->port[i].cmd_addr = portu + PORT_PRB;
+ probe_ent->port[i].cmd_addr = portu;
probe_ent->port[i].scr_addr = portu + PORT_SCONTROL;
ata_std_ports(&probe_ent->port[i]);
--
1.3.2
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH 6/6] sata_sil24: kill ops->tf_read() and use ata_std_noop_check_status()
2006-05-19 15:38 [PATCHSET 02/03] prep LLDDs for hotplug support, take 2 Tejun Heo
2006-05-19 15:38 ` [PATCH 4/6] sata_sil24: rename PORT_PRB to PORT_LRAM and add PORT_LRAM_SLOT_SZ Tejun Heo
@ 2006-05-19 15:38 ` Tejun Heo
2006-05-19 15:48 ` Jeff Garzik
2006-05-19 15:38 ` [PATCH 2/6] sata_sil: add new constants in preparation for new interrupt handler Tejun Heo
` (3 subsequent siblings)
5 siblings, 1 reply; 17+ messages in thread
From: Tejun Heo @ 2006-05-19 15:38 UTC (permalink / raw)
To: jgarzik, mlord, albertcc, alan, axboe, forrest.zhao, linux-ide; +Cc: Tejun Heo
sil24 doesn't have single TF image. Result TF is bound to each
command. As libata now allows TF-less implementation, kill
ops->tf_read and use ata_std_noop_check_status() for check_status
callbacks. Result TF is loaded directly from LRAM into qc->result_tf
if necessary.
This patch also makes sil24_hardreset() to request followup SRST as
that's the only way to wait for !BSY. Note that the original
implementation never worked - if the cached status was !BSY,
ata_busy_sleep() finished immediately; otherwise, it timed out
regardless of the actual device status.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/sata_sil24.c | 58 +++++++++++++++------------------------------
1 files changed, 19 insertions(+), 39 deletions(-)
38e62fb359d3447790ceb43f47ab8c473894f05f
diff --git a/drivers/scsi/sata_sil24.c b/drivers/scsi/sata_sil24.c
index 89d5d70..def1378 100644
--- a/drivers/scsi/sata_sil24.c
+++ b/drivers/scsi/sata_sil24.c
@@ -311,7 +311,6 @@ static struct sil24_cerr_info {
struct sil24_port_priv {
union sil24_cmd_block *cmd_block; /* 32 cmd blocks */
dma_addr_t cmd_block_dma; /* DMA base addr for them */
- struct ata_taskfile tf; /* Cached taskfile registers */
};
/* ap->host_set->private_data */
@@ -321,10 +320,8 @@ struct sil24_host_priv {
};
static void sil24_dev_config(struct ata_port *ap, struct ata_device *dev);
-static u8 sil24_check_status(struct ata_port *ap);
static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg);
static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val);
-static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
static int sil24_probe_reset(struct ata_port *ap, unsigned int *classes);
static void sil24_qc_prep(struct ata_queued_cmd *qc);
static unsigned int sil24_qc_issue(struct ata_queued_cmd *qc);
@@ -378,12 +375,10 @@ static const struct ata_port_operations
.dev_config = sil24_dev_config,
- .check_status = sil24_check_status,
- .check_altstatus = sil24_check_status,
+ .check_status = ata_noop_check_status,
+ .check_altstatus = ata_noop_check_status,
.dev_select = ata_noop_dev_select,
- .tf_read = sil24_tf_read,
-
.probe_reset = sil24_probe_reset,
.qc_prep = sil24_qc_prep,
@@ -460,21 +455,15 @@ static void sil24_dev_config(struct ata_
writel(PORT_CS_CDB16, port + PORT_CTRL_CLR);
}
-static inline void sil24_update_tf(struct ata_port *ap)
+static void sil24_read_tf(struct ata_port *ap, int tag, struct ata_taskfile *tf)
{
- struct sil24_port_priv *pp = ap->private_data;
void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;
- struct sil24_prb __iomem *prb = port;
+ struct sil24_prb __iomem *prb;
u8 fis[6 * 4];
- memcpy_fromio(fis, prb->fis, 6 * 4);
- ata_tf_from_fis(fis, &pp->tf);
-}
-
-static u8 sil24_check_status(struct ata_port *ap)
-{
- struct sil24_port_priv *pp = ap->private_data;
- return pp->tf.command;
+ prb = port + PORT_LRAM + tag * PORT_LRAM_SLOT_SZ;
+ memcpy_fromio(fis, prb->fis, sizeof(fis));
+ ata_tf_from_fis(fis, tf);
}
static int sil24_scr_map[] = {
@@ -505,12 +494,6 @@ static void sil24_scr_write(struct ata_p
}
}
-static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
-{
- struct sil24_port_priv *pp = ap->private_data;
- *tf = pp->tf;
-}
-
static int sil24_init_port(struct ata_port *ap)
{
void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;
@@ -533,6 +516,7 @@ static int sil24_softreset(struct ata_po
struct sil24_port_priv *pp = ap->private_data;
struct sil24_prb *prb = &pp->cmd_block[0].ata.prb;
dma_addr_t paddr = pp->cmd_block_dma;
+ struct ata_taskfile tf;
u32 mask, irq_stat;
const char *reason;
@@ -572,8 +556,8 @@ static int sil24_softreset(struct ata_po
goto err;
}
- sil24_update_tf(ap);
- *class = ata_dev_classify(&pp->tf);
+ sil24_read_tf(ap, 0, &tf);
+ *class = ata_dev_classify(&tf);
if (*class == ATA_DEV_UNKNOWN)
*class = ATA_DEV_NONE;
@@ -608,7 +592,7 @@ static int sil24_hardreset(struct ata_po
/* SStatus oscillates between zero and valid status after
* DEV_RST, debounce it.
*/
- rc = sata_phy_debounce(ap, sata_deb_timing_eh);
+ rc = sata_phy_debounce(ap, sata_deb_timing_before_fsrst);
if (rc) {
reason = "PHY debouncing failed";
goto err;
@@ -621,15 +605,13 @@ static int sil24_hardreset(struct ata_po
goto err;
}
- if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
- reason = "device not ready";
- goto err;
- }
-
- /* sil24 doesn't report device class code after hardreset,
- * leave *class alone.
+ /* Sil24 doesn't store signature FIS after hardreset, so we
+ * can't wait for BSY to clear. Some devices take a long time
+ * to get ready and those devices will choke if we don't wait
+ * for BSY clearance here. Tell libata to perform follow-up
+ * softreset.
*/
- return 0;
+ return -EAGAIN;
err:
ata_port_printk(ap, KERN_ERR, "hardreset failed (%s)\n", reason);
@@ -816,7 +798,7 @@ static void sil24_error_intr(struct ata_
/* record error info */
qc = ata_qc_from_tag(ap, ap->active_tag);
if (qc) {
- sil24_update_tf(ap);
+ sil24_read_tf(ap, sil24_tag(qc->tag), &qc->result_tf);
qc->err_mask |= err_mask;
} else
ehi->err_mask |= err_mask;
@@ -834,7 +816,7 @@ static void sil24_error_intr(struct ata_
static void sil24_finish_qc(struct ata_queued_cmd *qc)
{
if (qc->flags & ATA_QCFLAG_RESULT_TF)
- sil24_update_tf(qc->ap);
+ sil24_read_tf(qc->ap, sil24_tag(qc->tag), &qc->result_tf);
}
static inline void sil24_host_intr(struct ata_port *ap)
@@ -954,8 +936,6 @@ static int sil24_port_start(struct ata_p
if (!pp)
goto err_out;
- pp->tf.command = ATA_DRDY;
-
cb = dma_alloc_coherent(dev, cb_size, &cb_dma, GFP_KERNEL);
if (!cb)
goto err_out_pp;
--
1.3.2
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH 6/6] sata_sil24: kill ops->tf_read() and use ata_std_noop_check_status()
2006-05-19 15:38 ` [PATCH 6/6] sata_sil24: kill ops->tf_read() and use ata_std_noop_check_status() Tejun Heo
@ 2006-05-19 15:48 ` Jeff Garzik
0 siblings, 0 replies; 17+ messages in thread
From: Jeff Garzik @ 2006-05-19 15:48 UTC (permalink / raw)
To: Tejun Heo; +Cc: mlord, albertcc, alan, axboe, forrest.zhao, linux-ide
Tejun Heo wrote:
> sil24 doesn't have single TF image. Result TF is bound to each
> command. As libata now allows TF-less implementation, kill
> ops->tf_read and use ata_std_noop_check_status() for check_status
> callbacks. Result TF is loaded directly from LRAM into qc->result_tf
> if necessary.
>
> This patch also makes sil24_hardreset() to request followup SRST as
> that's the only way to wait for !BSY. Note that the original
> implementation never worked - if the cached status was !BSY,
> ata_busy_sleep() finished immediately; otherwise, it timed out
> regardless of the actual device status.
>
> Signed-off-by: Tejun Heo <htejun@gmail.com>
NAK, for reasons described in previous patchset.
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH 2/6] sata_sil: add new constants in preparation for new interrupt handler
2006-05-19 15:38 [PATCHSET 02/03] prep LLDDs for hotplug support, take 2 Tejun Heo
2006-05-19 15:38 ` [PATCH 4/6] sata_sil24: rename PORT_PRB to PORT_LRAM and add PORT_LRAM_SLOT_SZ Tejun Heo
2006-05-19 15:38 ` [PATCH 6/6] sata_sil24: kill ops->tf_read() and use ata_std_noop_check_status() Tejun Heo
@ 2006-05-19 15:38 ` Tejun Heo
2006-05-19 15:38 ` [PATCH 1/6] libata: export ata_hsm_move() Tejun Heo
` (2 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Tejun Heo @ 2006-05-19 15:38 UTC (permalink / raw)
To: jgarzik, mlord, albertcc, alan, axboe, forrest.zhao, linux-ide; +Cc: Tejun Heo
sata_sil is about to get a brand new interrupt handler. Add relevant
constants.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/sata_sil.c | 24 ++++++++++++++++++++----
1 files changed, 20 insertions(+), 4 deletions(-)
26c5ba2a53bbce1e60bb065eedf2fe24c706b91f
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
index aa63044..e34b9aa 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/scsi/sata_sil.c
@@ -54,6 +54,7 @@ enum {
*/
SIL_FLAG_RERR_ON_DMA_ACT = (1 << 29),
SIL_FLAG_MOD15WRITE = (1 << 30),
+
SIL_DFL_HOST_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO,
@@ -84,6 +85,20 @@ enum {
/* BMDMA/BMDMA2 */
SIL_INTR_STEERING = (1 << 1),
+ SIL_DMA_ENABLE = (1 << 0), /* DMA run switch */
+ SIL_DMA_RDWR = (1 << 3), /* DMA Rd-Wr */
+ SIL_DMA_SATA_IRQ = (1 << 4), /* OR of all SATA IRQs */
+ SIL_DMA_ACTIVE = (1 << 16), /* DMA running */
+ SIL_DMA_ERROR = (1 << 17), /* PCI bus error */
+ SIL_DMA_COMPLETE = (1 << 18), /* cmd complete / IRQ pending */
+ SIL_DMA_N_SATA_IRQ = (1 << 6), /* SATA_IRQ for the next channel */
+ SIL_DMA_N_ACTIVE = (1 << 24), /* ACTIVE for the next channel */
+ SIL_DMA_N_ERROR = (1 << 25), /* ERROR for the next channel */
+ SIL_DMA_N_COMPLETE = (1 << 26), /* COMPLETE for the next channel */
+
+ /* SIEN */
+ SIL_SIEN_N = (1 << 16), /* triggered by SError.N */
+
/*
* Others
*/
@@ -225,6 +240,7 @@ static const struct {
unsigned long tf; /* ATA taskfile register block */
unsigned long ctl; /* ATA control/altstatus register block */
unsigned long bmdma; /* DMA register block */
+ unsigned long bmdma2; /* DMA register block #2 */
unsigned long fifo_cfg; /* FIFO Valid Byte Count and Control */
unsigned long scr; /* SATA control register block */
unsigned long sien; /* SATA Interrupt Enable register */
@@ -232,10 +248,10 @@ static const struct {
unsigned long sfis_cfg; /* SATA FIS reception config register */
} sil_port[] = {
/* port 0 ... */
- { 0x80, 0x8A, 0x00, 0x40, 0x100, 0x148, 0xb4, 0x14c },
- { 0xC0, 0xCA, 0x08, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc },
- { 0x280, 0x28A, 0x200, 0x240, 0x300, 0x348, 0x2b4, 0x34c },
- { 0x2C0, 0x2CA, 0x208, 0x244, 0x380, 0x3c8, 0x2f4, 0x3cc },
+ { 0x80, 0x8A, 0x00, 0x10, 0x40, 0x100, 0x148, 0xb4, 0x14c },
+ { 0xC0, 0xCA, 0x08, 0x18, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc },
+ { 0x280, 0x28A, 0x200, 0x210, 0x240, 0x300, 0x348, 0x2b4, 0x34c },
+ { 0x2C0, 0x2CA, 0x208, 0x218, 0x244, 0x380, 0x3c8, 0x2f4, 0x3cc },
/* ... port 3 */
};
--
1.3.2
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH 1/6] libata: export ata_hsm_move()
2006-05-19 15:38 [PATCHSET 02/03] prep LLDDs for hotplug support, take 2 Tejun Heo
` (2 preceding siblings ...)
2006-05-19 15:38 ` [PATCH 2/6] sata_sil: add new constants in preparation for new interrupt handler Tejun Heo
@ 2006-05-19 15:38 ` Tejun Heo
2006-05-19 15:38 ` [PATCH 3/6] sata_sil: new interrupt handler Tejun Heo
2006-05-19 15:38 ` [PATCH 5/6] sata_sil24: use sata_phy_debounce() in sil24_hardreset() Tejun Heo
5 siblings, 0 replies; 17+ messages in thread
From: Tejun Heo @ 2006-05-19 15:38 UTC (permalink / raw)
To: jgarzik, mlord, albertcc, alan, axboe, forrest.zhao, linux-ide; +Cc: Tejun Heo
ata_hsm_move() will be used by LLDDs which depend on standard PIO HSM
but implement their own interrupt handlers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/libata-core.c | 6 +++---
include/linux/libata.h | 2 ++
2 files changed, 5 insertions(+), 3 deletions(-)
cb28a26fe7a13513c15d26f8099231ab9c419d2d
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index b2197b0..1809f98 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -4137,9 +4137,8 @@ static void ata_hsm_qc_complete(struct a
* RETURNS:
* 1 when poll next status needed, 0 otherwise.
*/
-
-static int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
- u8 status, int in_wq)
+int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
+ u8 status, int in_wq)
{
unsigned long flags = 0;
int poll_next;
@@ -5861,6 +5860,7 @@ EXPORT_SYMBOL_GPL(ata_device_add);
EXPORT_SYMBOL_GPL(ata_host_set_remove);
EXPORT_SYMBOL_GPL(ata_sg_init);
EXPORT_SYMBOL_GPL(ata_sg_init_one);
+EXPORT_SYMBOL_GPL(ata_hsm_move);
EXPORT_SYMBOL_GPL(ata_qc_complete);
EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
EXPORT_SYMBOL_GPL(ata_qc_issue_prot);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index f078c4c..5a382bf 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -712,6 +712,8 @@ extern void ata_bmdma_drive_eh(struct at
ata_postreset_fn_t postreset);
extern void ata_bmdma_error_handler(struct ata_port *ap);
extern void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc);
+extern int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
+ u8 status, int in_wq);
extern void ata_qc_complete(struct ata_queued_cmd *qc);
extern int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active,
void (*finish_qc)(struct ata_queued_cmd *));
--
1.3.2
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH 3/6] sata_sil: new interrupt handler
2006-05-19 15:38 [PATCHSET 02/03] prep LLDDs for hotplug support, take 2 Tejun Heo
` (3 preceding siblings ...)
2006-05-19 15:38 ` [PATCH 1/6] libata: export ata_hsm_move() Tejun Heo
@ 2006-05-19 15:38 ` Tejun Heo
2006-05-19 15:46 ` Jeff Garzik
2006-05-19 15:38 ` [PATCH 5/6] sata_sil24: use sata_phy_debounce() in sil24_hardreset() Tejun Heo
5 siblings, 1 reply; 17+ messages in thread
From: Tejun Heo @ 2006-05-19 15:38 UTC (permalink / raw)
To: jgarzik, mlord, albertcc, alan, axboe, forrest.zhao, linux-ide; +Cc: Tejun Heo
The DMA complete bit of these controllers reflects ATA IRQ status
while no DMA command is in progress. So, we can tell whether the
controller is raising an interrupt or not in deterministic manner.
This patch gives sata_sil its own interrupt handler which behaves much
better than the original one in terms of error detection and handling.
This change is also necessary for later hotplug support.
Further improvements are possible, in both 2 and 4 ports versions, we
can get all status with only one readl and using custom bmdma
operations can further cut down register accesses.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/sata_sil.c | 94 +++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 93 insertions(+), 1 deletions(-)
6a07f3409026b2a27e4057302d9031d3c197d074
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
index e34b9aa..cbced4b 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/scsi/sata_sil.c
@@ -111,6 +111,8 @@ static void sil_dev_config(struct ata_po
static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static void sil_post_set_mode (struct ata_port *ap);
+static irqreturn_t sil_interrupt(int irq, void *dev_instance,
+ struct pt_regs *regs);
static void sil_freeze(struct ata_port *ap);
static void sil_thaw(struct ata_port *ap);
@@ -195,7 +197,7 @@ static const struct ata_port_operations
.thaw = sil_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
- .irq_handler = ata_interrupt,
+ .irq_handler = sil_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.scr_read = sil_scr_read,
.scr_write = sil_scr_write,
@@ -335,6 +337,96 @@ static void sil_scr_write (struct ata_po
writel(val, mmio);
}
+static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
+{
+ struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag);
+ u8 status;
+
+ if (unlikely(!qc || qc->tf.ctl & ATA_NIEN))
+ goto freeze;
+
+ /* Check whether we are expecting interrupt in this state */
+ switch (ap->hsm_task_state) {
+ case HSM_ST_FIRST:
+ /* Some pre-ATAPI-4 devices assert INTRQ
+ * at this state when ready to receive CDB.
+ */
+
+ /* Check the ATA_DFLAG_CDB_INTR flag is enough here.
+ * The flag was turned on only for atapi devices.
+ * No need to check is_atapi_taskfile(&qc->tf) again.
+ */
+ if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
+ goto err_hsm;
+ break;
+ case HSM_ST_LAST:
+ if (qc->tf.protocol == ATA_PROT_DMA ||
+ qc->tf.protocol == ATA_PROT_ATAPI_DMA) {
+ /* clear DMA-Start bit */
+ ap->ops->bmdma_stop(qc);
+
+ if (bmdma2 & SIL_DMA_ERROR) {
+ qc->err_mask |= AC_ERR_HOST_BUS;
+ ap->hsm_task_state = HSM_ST_ERR;
+ }
+ }
+ break;
+ case HSM_ST:
+ break;
+ default:
+ goto err_hsm;
+ }
+
+ /* check main status, clearing INTRQ */
+ status = ata_chk_status(ap);
+ if (unlikely(status & ATA_BUSY))
+ goto err_hsm;
+
+ /* ack bmdma irq events */
+ ap->ops->irq_clear(ap);
+
+ /* kick HSM in the ass */
+ ata_hsm_move(ap, qc, status, 0);
+
+ return;
+
+ err_hsm:
+ qc->err_mask |= AC_ERR_HSM;
+ freeze:
+ ata_port_freeze(ap);
+}
+
+static irqreturn_t sil_interrupt(int irq, void *dev_instance,
+ struct pt_regs *regs)
+{
+ struct ata_host_set *host_set = dev_instance;
+ void __iomem *mmio_base = host_set->mmio_base;
+ int handled = 0;
+ unsigned long flags;
+ int i;
+
+ /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
+ spin_lock_irqsave(&host_set->lock, flags);
+
+ for (i = 0; i < host_set->n_ports; i++) {
+ struct ata_port *ap = host_set->ports[i];
+ u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
+
+ if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
+ continue;
+
+ if (!(bmdma2 & SIL_DMA_COMPLETE))
+ continue;
+
+ sil_host_intr(ap, bmdma2);
+ handled = 1;
+ }
+
+ spin_unlock_irqrestore(&host_set->lock, flags);
+
+ return IRQ_RETVAL(handled);
+}
+
static void sil_freeze(struct ata_port *ap)
{
void __iomem *mmio_base = ap->host_set->mmio_base;
--
1.3.2
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH 3/6] sata_sil: new interrupt handler
2006-05-19 15:38 ` [PATCH 3/6] sata_sil: new interrupt handler Tejun Heo
@ 2006-05-19 15:46 ` Jeff Garzik
2006-05-23 14:50 ` Tejun Heo
0 siblings, 1 reply; 17+ messages in thread
From: Jeff Garzik @ 2006-05-19 15:46 UTC (permalink / raw)
To: Tejun Heo; +Cc: mlord, albertcc, alan, axboe, forrest.zhao, linux-ide
Tejun Heo wrote:
> The DMA complete bit of these controllers reflects ATA IRQ status
> while no DMA command is in progress. So, we can tell whether the
> controller is raising an interrupt or not in deterministic manner.
> This patch gives sata_sil its own interrupt handler which behaves much
> better than the original one in terms of error detection and handling.
> This change is also necessary for later hotplug support.
>
> Further improvements are possible, in both 2 and 4 ports versions, we
> can get all status with only one readl and using custom bmdma
> operations can further cut down register accesses.
>
> Signed-off-by: Tejun Heo <htejun@gmail.com>
>
> ---
>
> drivers/scsi/sata_sil.c | 94 +++++++++++++++++++++++++++++++++++++++++++++++
> 1 files changed, 93 insertions(+), 1 deletions(-)
>
> 6a07f3409026b2a27e4057302d9031d3c197d074
> diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
> index e34b9aa..cbced4b 100644
> --- a/drivers/scsi/sata_sil.c
> +++ b/drivers/scsi/sata_sil.c
> @@ -111,6 +111,8 @@ static void sil_dev_config(struct ata_po
> static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
> static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
> static void sil_post_set_mode (struct ata_port *ap);
> +static irqreturn_t sil_interrupt(int irq, void *dev_instance,
> + struct pt_regs *regs);
> static void sil_freeze(struct ata_port *ap);
> static void sil_thaw(struct ata_port *ap);
>
> @@ -195,7 +197,7 @@ static const struct ata_port_operations
> .thaw = sil_thaw,
> .error_handler = ata_bmdma_error_handler,
> .post_internal_cmd = ata_bmdma_post_internal_cmd,
> - .irq_handler = ata_interrupt,
> + .irq_handler = sil_interrupt,
> .irq_clear = ata_bmdma_irq_clear,
> .scr_read = sil_scr_read,
> .scr_write = sil_scr_write,
> @@ -335,6 +337,96 @@ static void sil_scr_write (struct ata_po
> writel(val, mmio);
> }
>
> +static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
> +{
> + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag);
> + u8 status;
> +
> + if (unlikely(!qc || qc->tf.ctl & ATA_NIEN))
> + goto freeze;
> +
> + /* Check whether we are expecting interrupt in this state */
> + switch (ap->hsm_task_state) {
> + case HSM_ST_FIRST:
> + /* Some pre-ATAPI-4 devices assert INTRQ
> + * at this state when ready to receive CDB.
> + */
> +
> + /* Check the ATA_DFLAG_CDB_INTR flag is enough here.
> + * The flag was turned on only for atapi devices.
> + * No need to check is_atapi_taskfile(&qc->tf) again.
> + */
> + if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
> + goto err_hsm;
> + break;
> + case HSM_ST_LAST:
> + if (qc->tf.protocol == ATA_PROT_DMA ||
> + qc->tf.protocol == ATA_PROT_ATAPI_DMA) {
> + /* clear DMA-Start bit */
> + ap->ops->bmdma_stop(qc);
> +
> + if (bmdma2 & SIL_DMA_ERROR) {
> + qc->err_mask |= AC_ERR_HOST_BUS;
> + ap->hsm_task_state = HSM_ST_ERR;
> + }
> + }
> + break;
> + case HSM_ST:
> + break;
> + default:
> + goto err_hsm;
> + }
> +
> + /* check main status, clearing INTRQ */
> + status = ata_chk_status(ap);
> + if (unlikely(status & ATA_BUSY))
> + goto err_hsm;
> +
> + /* ack bmdma irq events */
> + ap->ops->irq_clear(ap);
Don't use hook in LLDD
> + /* kick HSM in the ass */
> + ata_hsm_move(ap, qc, status, 0);
> +
> + return;
> +
> + err_hsm:
> + qc->err_mask |= AC_ERR_HSM;
> + freeze:
> + ata_port_freeze(ap);
> +}
> +
> +static irqreturn_t sil_interrupt(int irq, void *dev_instance,
> + struct pt_regs *regs)
> +{
> + struct ata_host_set *host_set = dev_instance;
> + void __iomem *mmio_base = host_set->mmio_base;
> + int handled = 0;
> + unsigned long flags;
> + int i;
> +
> + /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
> + spin_lock_irqsave(&host_set->lock, flags);
> +
> + for (i = 0; i < host_set->n_ports; i++) {
> + struct ata_port *ap = host_set->ports[i];
> + u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
> +
> + if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
> + continue;
> +
> + if (!(bmdma2 & SIL_DMA_COMPLETE))
> + continue;
> +
> + sil_host_intr(ap, bmdma2);
> + handled = 1;
> + }
> +
> + spin_unlock_irqrestore(&host_set->lock, flags);
NAK, unconditionally use spin_lock() and spin_unlock() on this hardware.
ACK everything besides the two issues I mention in this email.
ACK patches 1 - 2, also.
Jeff
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH 3/6] sata_sil: new interrupt handler
2006-05-19 15:46 ` Jeff Garzik
@ 2006-05-23 14:50 ` Tejun Heo
2006-05-23 22:04 ` Jeff Garzik
0 siblings, 1 reply; 17+ messages in thread
From: Tejun Heo @ 2006-05-23 14:50 UTC (permalink / raw)
To: Jeff Garzik; +Cc: mlord, albertcc, alan, axboe, forrest.zhao, linux-ide
Jeff Garzik wrote:
>> + /* ack bmdma irq events */
>> + ap->ops->irq_clear(ap);
>
> Don't use hook in LLDD
Okay.
>> + spin_lock_irqsave(&host_set->lock, flags);
>> +
>> + for (i = 0; i < host_set->n_ports; i++) {
>> + struct ata_port *ap = host_set->ports[i];
>> + u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
>> +
>> + if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
>> + continue;
>> +
>> + if (!(bmdma2 & SIL_DMA_COMPLETE))
>> + continue;
>> +
>> + sil_host_intr(ap, bmdma2);
>> + handled = 1;
>> + }
>> +
>> + spin_unlock_irqrestore(&host_set->lock, flags);
>
> NAK, unconditionally use spin_lock() and spin_unlock() on this hardware.
Can you explain more on this? We almost never use those in libata and I
don't see what's different for sata_sil.
--
tejun
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH 3/6] sata_sil: new interrupt handler
2006-05-23 14:50 ` Tejun Heo
@ 2006-05-23 22:04 ` Jeff Garzik
2006-05-23 22:07 ` Tejun Heo
0 siblings, 1 reply; 17+ messages in thread
From: Jeff Garzik @ 2006-05-23 22:04 UTC (permalink / raw)
To: Tejun Heo; +Cc: mlord, albertcc, alan, axboe, forrest.zhao, linux-ide
Tejun Heo wrote:
> Jeff Garzik wrote:
>>> + /* ack bmdma irq events */
>>> + ap->ops->irq_clear(ap);
>>
>> Don't use hook in LLDD
>
> Okay.
>
>>> + spin_lock_irqsave(&host_set->lock, flags);
>>> +
>>> + for (i = 0; i < host_set->n_ports; i++) {
>>> + struct ata_port *ap = host_set->ports[i];
>>> + u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
>>> +
>>> + if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
>>> + continue;
>>> +
>>> + if (!(bmdma2 & SIL_DMA_COMPLETE))
>>> + continue;
>>> +
>>> + sil_host_intr(ap, bmdma2);
>>> + handled = 1;
>>> + }
>>> +
>>> + spin_unlock_irqrestore(&host_set->lock, flags);
>>
>> NAK, unconditionally use spin_lock() and spin_unlock() on this hardware.
>
> Can you explain more on this? We almost never use those in libata and I
> don't see what's different for sata_sil.
er, huh? _Most_ libata drivers use spin_lock().
The only case where spin_lock_irqsave() should be used is when you are
dealing with multiple independent interrupts, i.e. the legacy case of
irqs 14/15.
Thus, the core uses the safe-in-all-cases version, and drivers that
implement their own interrupt handler can implement the better version.
[jgarzik@pretzel linux-2.6]$ grep -wl spin_lock drivers/scsi/ahci.c
drivers/scsi/pdc_adma.c drivers/scsi/sata_*.c
drivers/scsi/ahci.c
drivers/scsi/pdc_adma.c
drivers/scsi/sata_mv.c
drivers/scsi/sata_promise.c
drivers/scsi/sata_qstor.c
drivers/scsi/sata_sil24.c
drivers/scsi/sata_sx4.c
drivers/scsi/sata_vsc.c
Jeff
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH 3/6] sata_sil: new interrupt handler
2006-05-23 22:04 ` Jeff Garzik
@ 2006-05-23 22:07 ` Tejun Heo
0 siblings, 0 replies; 17+ messages in thread
From: Tejun Heo @ 2006-05-23 22:07 UTC (permalink / raw)
To: Jeff Garzik; +Cc: mlord, albertcc, alan, axboe, forrest.zhao, linux-ide
Jeff Garzik wrote:
> Tejun Heo wrote:
>> Jeff Garzik wrote:
>>>> + /* ack bmdma irq events */
>>>> + ap->ops->irq_clear(ap);
>>>
>>> Don't use hook in LLDD
>>
>> Okay.
>>
>>>> + spin_lock_irqsave(&host_set->lock, flags);
>>>> +
>>>> + for (i = 0; i < host_set->n_ports; i++) {
>>>> + struct ata_port *ap = host_set->ports[i];
>>>> + u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
>>>> +
>>>> + if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
>>>> + continue;
>>>> +
>>>> + if (!(bmdma2 & SIL_DMA_COMPLETE))
>>>> + continue;
>>>> +
>>>> + sil_host_intr(ap, bmdma2);
>>>> + handled = 1;
>>>> + }
>>>> +
>>>> + spin_unlock_irqrestore(&host_set->lock, flags);
>>>
>>> NAK, unconditionally use spin_lock() and spin_unlock() on this hardware.
>>
>> Can you explain more on this? We almost never use those in libata and
>> I don't see what's different for sata_sil.
>
> er, huh? _Most_ libata drivers use spin_lock().
>
> The only case where spin_lock_irqsave() should be used is when you are
> dealing with multiple independent interrupts, i.e. the legacy case of
> irqs 14/15.
>
> Thus, the core uses the safe-in-all-cases version, and drivers that
> implement their own interrupt handler can implement the better version.
>
> [jgarzik@pretzel linux-2.6]$ grep -wl spin_lock drivers/scsi/ahci.c
> drivers/scsi/pdc_adma.c drivers/scsi/sata_*.c
> drivers/scsi/ahci.c
> drivers/scsi/pdc_adma.c
> drivers/scsi/sata_mv.c
> drivers/scsi/sata_promise.c
> drivers/scsi/sata_qstor.c
> drivers/scsi/sata_sil24.c
> drivers/scsi/sata_sx4.c
> drivers/scsi/sata_vsc.c
>
Ouch, you're right. Sorry about the noise.
--
tejun
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH 5/6] sata_sil24: use sata_phy_debounce() in sil24_hardreset()
2006-05-19 15:38 [PATCHSET 02/03] prep LLDDs for hotplug support, take 2 Tejun Heo
` (4 preceding siblings ...)
2006-05-19 15:38 ` [PATCH 3/6] sata_sil: new interrupt handler Tejun Heo
@ 2006-05-19 15:38 ` Tejun Heo
2006-05-19 15:47 ` Jeff Garzik
5 siblings, 1 reply; 17+ messages in thread
From: Tejun Heo @ 2006-05-19 15:38 UTC (permalink / raw)
To: jgarzik, mlord, albertcc, alan, axboe, forrest.zhao, linux-ide; +Cc: Tejun Heo
Do phy debouncing instead of unconditional wait after DEV_RST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/sata_sil24.c | 12 ++++++++----
1 files changed, 8 insertions(+), 4 deletions(-)
1f6218924d908e924488ea1ce855bc1ba62f6396
diff --git a/drivers/scsi/sata_sil24.c b/drivers/scsi/sata_sil24.c
index a39e8d0..89d5d70 100644
--- a/drivers/scsi/sata_sil24.c
+++ b/drivers/scsi/sata_sil24.c
@@ -591,7 +591,7 @@ static int sil24_hardreset(struct ata_po
{
void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;
const char *reason;
- int tout_msec;
+ int tout_msec, rc;
u32 tmp;
/* sil24 does the right thing(tm) without any protection */
@@ -605,10 +605,14 @@ static int sil24_hardreset(struct ata_po
tmp = ata_wait_register(port + PORT_CTRL_STAT,
PORT_CS_DEV_RST, PORT_CS_DEV_RST, 10, tout_msec);
- /* SStatus oscillates between zero and valid status for short
- * duration after DEV_RST, give it time to settle.
+ /* SStatus oscillates between zero and valid status after
+ * DEV_RST, debounce it.
*/
- msleep(100);
+ rc = sata_phy_debounce(ap, sata_deb_timing_eh);
+ if (rc) {
+ reason = "PHY debouncing failed";
+ goto err;
+ }
if (tmp & PORT_CS_DEV_RST) {
if (ata_port_offline(ap))
--
1.3.2
^ permalink raw reply related [flat|nested] 17+ messages in thread