From: Daniel Smolik <marvin@mydatex.cz>
To: linux-kernel@vger.kernel.org, sparclinux@vger.kernel.org
Subject: Re: sym53c8xx PCI card broken in 2.6.18
Date: Wed, 23 Aug 2006 21:01:34 +0000 [thread overview]
Message-ID: <44ECC22E.50206@mydatex.cz> (raw)
In-Reply-To: <200608221546.11532.dj@david-web.co.uk>
David Johnson napsal(a):
> Hi all,
>
> I'm running a Sun Ultra Enterprise 450 (SPARC64) machine which has an on-board
> SCSI controller and a PCI SCSI controller, both supported by the sym53c8xx
> driver.
>
> With 2.6.17.9 (and earlier) SCSI works perfectly, but with 2.6.18-rc4 and
> 2.6.18-rc4-git1 I'm getting errors on boot for all devices attached to the
> PCI card, but all the devices attached to the on-board controller are
> detected and configured OK.
>
> lspci identifies the on-board controller as:
> SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 03)
> and the PCI controller as:
> SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14)
>
> Here's the output from initialisation of the devices on the PCI card (repeated
> for every device):
> scsi2: sym-2.2.3
> scsi 2:0:0:0 ABORT operation started
> scsi 2:0:0:0 ABORT operation timed out
> scsi 2:0:0:0 DEVICE RESET operation started
> scsi 2:0:0:0 DEVICE RESET operation timed out
> scsi 2:0:0:0 BUS RESET operation started
> scsi 2:0:0:0 BUS RESET operation timed out
> scsi 2:0:0:0 HOST RESET operation started
> sym2: SCSI bus has been reset
> scsi 2:0:0:0 HOST RESET operation timed out
> scsi: device offlined - not ready after error recovery
>
> The devices on the PCI controller are a mixture of 'Fujitsu MAG3182L SUN18G'
> and 'Seagate ST318203LSUN18G' drives.
>
> Looking through the changelogs between 2.6.17.9 and 2.6.18-rc4-git1, I can't
> see any changes to sym53c8xx, so I'm guessing this has been caused by some
> generic SCSI subsystem change. Let me know if I can do any more to debug.
>
> Regards,
> David.
>
I must say that I have the same experience with E250 a D1000 disk array.
I think that is HW problem but I have the same symptom described before.
If I have disk in internal bay and controller all works perfect. But if I put
disk to D1000 I get the same error. I have use 2.6.18-rc3.
Dan
WARNING: multiple messages have this Message-ID (diff)
From: Daniel Smolik <marvin@mydatex.cz>
To: linux-kernel@vger.kernel.org, sparclinux@vger.kernel.org
Subject: Re: sym53c8xx PCI card broken in 2.6.18
Date: Wed, 23 Aug 2006 23:01:34 +0200 [thread overview]
Message-ID: <44ECC22E.50206@mydatex.cz> (raw)
In-Reply-To: <200608221546.11532.dj@david-web.co.uk>
David Johnson napsal(a):
> Hi all,
>
> I'm running a Sun Ultra Enterprise 450 (SPARC64) machine which has an on-board
> SCSI controller and a PCI SCSI controller, both supported by the sym53c8xx
> driver.
>
> With 2.6.17.9 (and earlier) SCSI works perfectly, but with 2.6.18-rc4 and
> 2.6.18-rc4-git1 I'm getting errors on boot for all devices attached to the
> PCI card, but all the devices attached to the on-board controller are
> detected and configured OK.
>
> lspci identifies the on-board controller as:
> SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 03)
> and the PCI controller as:
> SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14)
>
> Here's the output from initialisation of the devices on the PCI card (repeated
> for every device):
> scsi2: sym-2.2.3
> scsi 2:0:0:0 ABORT operation started
> scsi 2:0:0:0 ABORT operation timed out
> scsi 2:0:0:0 DEVICE RESET operation started
> scsi 2:0:0:0 DEVICE RESET operation timed out
> scsi 2:0:0:0 BUS RESET operation started
> scsi 2:0:0:0 BUS RESET operation timed out
> scsi 2:0:0:0 HOST RESET operation started
> sym2: SCSI bus has been reset
> scsi 2:0:0:0 HOST RESET operation timed out
> scsi: device offlined - not ready after error recovery
>
> The devices on the PCI controller are a mixture of 'Fujitsu MAG3182L SUN18G'
> and 'Seagate ST318203LSUN18G' drives.
>
> Looking through the changelogs between 2.6.17.9 and 2.6.18-rc4-git1, I can't
> see any changes to sym53c8xx, so I'm guessing this has been caused by some
> generic SCSI subsystem change. Let me know if I can do any more to debug.
>
> Regards,
> David.
>
I must say that I have the same experience with E250 a D1000 disk array.
I think that is HW problem but I have the same symptom described before.
If I have disk in internal bay and controller all works perfect. But if I put
disk to D1000 I get the same error. I have use 2.6.18-rc3.
Dan
next prev parent reply other threads:[~2006-08-23 21:01 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-08-22 14:46 sym53c8xx PCI card broken in 2.6.18 David Johnson
2006-08-22 14:46 ` David Johnson
2006-08-22 20:39 ` David Miller
2006-08-22 20:39 ` David Miller
2006-08-22 22:39 ` David Johnson
2006-08-22 22:39 ` David Johnson
2006-08-23 3:59 ` Eric Brower
2006-08-23 3:59 ` Eric Brower
2006-08-23 4:01 ` David Miller
2006-08-23 4:01 ` David Miller
2006-08-23 5:35 ` Eric Brower
2006-08-23 5:35 ` Eric Brower
2006-08-23 5:50 ` David Miller
2006-08-23 5:50 ` David Miller
2006-08-23 21:01 ` Daniel Smolik [this message]
2006-08-23 21:01 ` Daniel Smolik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=44ECC22E.50206@mydatex.cz \
--to=marvin@mydatex.cz \
--cc=linux-kernel@vger.kernel.org \
--cc=sparclinux@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.