* ethernet patch for kernel 2.6 for ml403 [not found] <mailman.270.1158283233.2423.linuxppc-embedded@ozlabs.org> @ 2006-09-15 3:24 ` Aleck Lin 2006-09-15 11:17 ` David H. Lynch Jr. 0 siblings, 1 reply; 3+ messages in thread From: Aleck Lin @ 2006-09-15 3:24 UTC (permalink / raw) To: linuxppc-embedded Hello, I found this patch that was posted back in January (http://ozlabs.org/pipermail/linuxppc-embedded/2006-January/021574.html). As I was trying it, there were some warnings and errors. When I fixed them as much as I could to the point of a successful compilation, I tried to boot this kernel image on ml403. However, it still complains that no network devices available. TWO questions. 1. Has anyone ever tried with the patch and been successful with it? 2. Why does it still complain no network devices found even though I thot I added the correct ethernet driver? Thanks for any help as I'm still relatively new to this. Aleck Here's my booting message. --------------------------------------------------- ## Booting image at 00800000 ... Image Name: Linux-2.6.17.8 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 854118 Bytes = 834.1 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## cmdline at 0x007FFF00 ... 0x007FFF37 memstart = 0x00000000 memsize = 0x04000000 flashstart = 0xFF800000 flashsize = 0x00800000 flashoffset = 0x00000000 sramstart = 0x00000000 sramsize = 0x00000000 bootflags = 0x0000012A procfreq = 300 MHz plb_busfreq = 100 MHz ethaddr = 00:11:22:33:44:55 IP addr = 192.168.200.230 baudrate = 9600 bps ## Loading RAMDisk Image at 01000000 ... Image Name: Simple Embedded Linux Framework Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 1437217 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Ramdisk to 03d03000, end 03e61e21 ... OK [ 0.000000] Linux version 2.6.17.8 (aleck@sac.gdatech.com) (gcc version 4.0.0 (DENX ELDK 4.0 4.0.0)) #87 Thu Sep 14 20:06:23 PDT 2006 [ 0.000000] Xilinx ML403 Reference System (Virtex-4 FX) [ 0.000000] Built 1 zonelists [ 0.000000] Kernel command line: console=ttyS0,9600 ip=192.168.200.230 root=/dev/ram0 rw [ 0.000000] Xilinx INTC #0 at 0x41200000 mapped to 0xFDFFE000 [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000151] Console: colour dummy device 80x25 [ 0.000567] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.001213] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.013282] Memory: 61632k available (1308k kernel code, 476k data, 84k init, 0k highmem) [ 0.200420] Mount-cache hash table entries: 512 [ 0.202863] checking if image is initramfs...it isn't (no cpio magic); looks like an initrd [ 0.863139] Freeing initrd memory: 1403k freed [ 0.866364] NET: Registered protocol family 16 [ 0.869487] Generic PHY: Registered new driver [ 0.874412] NET: Registered protocol family 2 [ 0.912357] IP route cache hash table entries: 512 (order: -1, 2048 bytes) [ 0.913062] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.913241] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.913339] TCP: Hash tables configured (established 2048 bind 1024) [ 0.913368] TCP reno registered [ 0.920012] io scheduler noop registered [ 0.920111] io scheduler anticipatory registered (default) [ 0.920187] io scheduler deadline registered [ 0.920346] io scheduler cfq registered [ 0.958113] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.962450] serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 3) is a 16550A [ 2.871187] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 2.961972] allocating ethernet device... [ 3.010204] eth%d: using fifo mode. [ 3.052064] eth%d: Xilinx EMAC #0 at 0x80400000 mapped to 0xC5000000, irq=31 [ 3.136606] eth%d: id 2.0a; block id 0, type 8 [ 3.190431] Marvell 88E1101: Registered new driver [ 3.250101] tun: Universal TUN/TAP device driver, 1.6 [ 3.310712] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 3.385845] mice: PS/2 mouse device common for all mice [ 3.448583] TCP bic registered [ 3.485307] NET: Registered protocol family 1 [ 3.537610] NET: Registered protocol family 17 [ 4.096219] IP-Config: No network devices available. [ 4.156871] RAMDISK: Compressed image found at block 0 [ 5.002841] VFS: Mounted root (ext2 filesystem). [ 5.058432] Freeing unused kernel memory: 84k init ### Application running ... BusyBox v(null) ((null)) Built-in shell (msh) # ------------------------------------------------------------------ ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: ethernet patch for kernel 2.6 for ml403 2006-09-15 3:24 ` ethernet patch for kernel 2.6 for ml403 Aleck Lin @ 2006-09-15 11:17 ` David H. Lynch Jr. 2006-09-15 17:38 ` Aleck Lin 0 siblings, 1 reply; 3+ messages in thread From: David H. Lynch Jr. @ 2006-09-15 11:17 UTC (permalink / raw) To: Aleck Lin; +Cc: linuxppc-embedded I have used a later version of what I beleive is the same patch. http://source.mvista.com/~ank/paulus-powerpc/20060309/ This is for the PLB TEMAC. My guess based on your capture below is that you are using that IP. Did you try ifconfig eth0 xxx.xxx.xxx.xxx ? I do not know what is in the rest of your init setup but something must asign the IP and bring up the interface. Aleck Lin wrote: > Hello, > > I found this patch that was posted back in January > (http://ozlabs.org/pipermail/linuxppc-embedded/2006-January/021574.html). > > As I was trying it, there were some warnings and errors. When I fixed them > as much as I could to the point of a successful compilation, I tried to boot > this kernel image on ml403. However, it still complains that no network > devices available. > > TWO questions. > 1. Has anyone ever tried with the patch and been successful with it? > 2. Why does it still complain no network devices found even though I thot I > added the correct ethernet driver? > > Thanks for any help as I'm still relatively new to this. > > Aleck > > > Here's my booting message. > > --------------------------------------------------- > ## Booting image at 00800000 ... > Image Name: Linux-2.6.17.8 > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 854118 Bytes = 834.1 kB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > ## cmdline at 0x007FFF00 ... 0x007FFF37 > memstart = 0x00000000 > memsize = 0x04000000 > flashstart = 0xFF800000 > flashsize = 0x00800000 > flashoffset = 0x00000000 > sramstart = 0x00000000 > sramsize = 0x00000000 > bootflags = 0x0000012A > procfreq = 300 MHz > plb_busfreq = 100 MHz > ethaddr = 00:11:22:33:44:55 > IP addr = 192.168.200.230 > baudrate = 9600 bps > ## Loading RAMDisk Image at 01000000 ... > Image Name: Simple Embedded Linux Framework > Image Type: PowerPC Linux RAMDisk Image (gzip compressed) > Data Size: 1437217 Bytes = 1.4 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Loading Ramdisk to 03d03000, end 03e61e21 ... OK > [ 0.000000] Linux version 2.6.17.8 (aleck@sac.gdatech.com) (gcc version > 4.0.0 (DENX ELDK 4.0 4.0.0)) #87 Thu Sep 14 20:06:23 PDT 2006 > [ 0.000000] Xilinx ML403 Reference System (Virtex-4 FX) > [ 0.000000] Built 1 zonelists > [ 0.000000] Kernel command line: console=ttyS0,9600 ip=192.168.200.230 > root=/dev/ram0 rw > [ 0.000000] Xilinx INTC #0 at 0x41200000 mapped to 0xFDFFE000 > [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) > [ 0.000151] Console: colour dummy device 80x25 > [ 0.000567] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) > [ 0.001213] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) > [ 0.013282] Memory: 61632k available (1308k kernel code, 476k data, 84k > init, 0k highmem) > [ 0.200420] Mount-cache hash table entries: 512 > [ 0.202863] checking if image is initramfs...it isn't (no cpio magic); > looks like an initrd > [ 0.863139] Freeing initrd memory: 1403k freed > [ 0.866364] NET: Registered protocol family 16 > [ 0.869487] Generic PHY: Registered new driver > [ 0.874412] NET: Registered protocol family 2 > [ 0.912357] IP route cache hash table entries: 512 (order: -1, 2048 > bytes) > [ 0.913062] TCP established hash table entries: 2048 (order: 1, 8192 > bytes) > [ 0.913241] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) > [ 0.913339] TCP: Hash tables configured (established 2048 bind 1024) > [ 0.913368] TCP reno registered > [ 0.920012] io scheduler noop registered > [ 0.920111] io scheduler anticipatory registered (default) > [ 0.920187] io scheduler deadline registered > [ 0.920346] io scheduler cfq registered > [ 0.958113] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ > sharing disabled > [ 0.962450] serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 3) is a 16550A > [ 2.871187] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 > blocksize > [ 2.961972] allocating ethernet device... > [ 3.010204] eth%d: using fifo mode. > [ 3.052064] eth%d: Xilinx EMAC #0 at 0x80400000 mapped to 0xC5000000, > irq=31 > [ 3.136606] eth%d: id 2.0a; block id 0, type 8 > [ 3.190431] Marvell 88E1101: Registered new driver > [ 3.250101] tun: Universal TUN/TAP device driver, 1.6 > [ 3.310712] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> > [ 3.385845] mice: PS/2 mouse device common for all mice > [ 3.448583] TCP bic registered > [ 3.485307] NET: Registered protocol family 1 > [ 3.537610] NET: Registered protocol family 17 > [ 4.096219] IP-Config: No network devices available. > [ 4.156871] RAMDISK: Compressed image found at block 0 > [ 5.002841] VFS: Mounted root (ext2 filesystem). > [ 5.058432] Freeing unused kernel memory: 84k init > ### Application running ... > > > BusyBox v(null) ((null)) Built-in shell (msh) > # > ------------------------------------------------------------------ > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > -- Dave Lynch DLA Systems Software Development: Embedded Linux 717.627.3770 dhlii@dlasys.net http://www.dlasys.net fax: 1.253.369.9244 Cell: 1.717.587.7774 Over 25 years' experience in platforms, languages, and technologies too numerous to list. "Any intelligent fool can make things bigger and more complex... It takes a touch of genius - and a lot of courage to move in the opposite direction." Albert Einstein ^ permalink raw reply [flat|nested] 3+ messages in thread
* RE: ethernet patch for kernel 2.6 for ml403 2006-09-15 11:17 ` David H. Lynch Jr. @ 2006-09-15 17:38 ` Aleck Lin 0 siblings, 0 replies; 3+ messages in thread From: Aleck Lin @ 2006-09-15 17:38 UTC (permalink / raw) To: 'David H. Lynch Jr.'; +Cc: linuxppc-embedded David, I believe I'm using plb_emac. Is it correct that I'm looking for the Xilinx_enet driver patch?? I tried ifconfig, but no luck. ------------------------------------------ #ifconfig eth0 address 192.168.200.230 SIOCSIFADDR: No such device # ------------------------------------------- Thanks Aleck -----Original Message----- From: David H. Lynch Jr. [mailto:dhlii@dlasys.net] Sent: Friday, September 15, 2006 4:17 AM To: Aleck Lin Cc: linuxppc-embedded@ozlabs.org Subject: Re: ethernet patch for kernel 2.6 for ml403 I have used a later version of what I beleive is the same patch. http://source.mvista.com/~ank/paulus-powerpc/20060309/ This is for the PLB TEMAC. My guess based on your capture below is that you are using that IP. Did you try ifconfig eth0 xxx.xxx.xxx.xxx ? I do not know what is in the rest of your init setup but something must asign the IP and bring up the interface. Aleck Lin wrote: > Hello, > > I found this patch that was posted back in January > (http://ozlabs.org/pipermail/linuxppc-embedded/2006-January/021574.html). > > As I was trying it, there were some warnings and errors. When I fixed them > as much as I could to the point of a successful compilation, I tried to boot > this kernel image on ml403. However, it still complains that no network > devices available. > > TWO questions. > 1. Has anyone ever tried with the patch and been successful with it? > 2. Why does it still complain no network devices found even though I thot I > added the correct ethernet driver? > > Thanks for any help as I'm still relatively new to this. > > Aleck > > > Here's my booting message. > > --------------------------------------------------- > ## Booting image at 00800000 ... > Image Name: Linux-2.6.17.8 > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 854118 Bytes = 834.1 kB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > ## cmdline at 0x007FFF00 ... 0x007FFF37 > memstart = 0x00000000 > memsize = 0x04000000 > flashstart = 0xFF800000 > flashsize = 0x00800000 > flashoffset = 0x00000000 > sramstart = 0x00000000 > sramsize = 0x00000000 > bootflags = 0x0000012A > procfreq = 300 MHz > plb_busfreq = 100 MHz > ethaddr = 00:11:22:33:44:55 > IP addr = 192.168.200.230 > baudrate = 9600 bps > ## Loading RAMDisk Image at 01000000 ... > Image Name: Simple Embedded Linux Framework > Image Type: PowerPC Linux RAMDisk Image (gzip compressed) > Data Size: 1437217 Bytes = 1.4 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Loading Ramdisk to 03d03000, end 03e61e21 ... OK > [ 0.000000] Linux version 2.6.17.8 (aleck@sac.gdatech.com) (gcc version > 4.0.0 (DENX ELDK 4.0 4.0.0)) #87 Thu Sep 14 20:06:23 PDT 2006 > [ 0.000000] Xilinx ML403 Reference System (Virtex-4 FX) > [ 0.000000] Built 1 zonelists > [ 0.000000] Kernel command line: console=ttyS0,9600 ip=192.168.200.230 > root=/dev/ram0 rw > [ 0.000000] Xilinx INTC #0 at 0x41200000 mapped to 0xFDFFE000 > [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) > [ 0.000151] Console: colour dummy device 80x25 > [ 0.000567] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) > [ 0.001213] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) > [ 0.013282] Memory: 61632k available (1308k kernel code, 476k data, 84k > init, 0k highmem) > [ 0.200420] Mount-cache hash table entries: 512 > [ 0.202863] checking if image is initramfs...it isn't (no cpio magic); > looks like an initrd > [ 0.863139] Freeing initrd memory: 1403k freed > [ 0.866364] NET: Registered protocol family 16 > [ 0.869487] Generic PHY: Registered new driver > [ 0.874412] NET: Registered protocol family 2 > [ 0.912357] IP route cache hash table entries: 512 (order: -1, 2048 > bytes) > [ 0.913062] TCP established hash table entries: 2048 (order: 1, 8192 > bytes) > [ 0.913241] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) > [ 0.913339] TCP: Hash tables configured (established 2048 bind 1024) > [ 0.913368] TCP reno registered > [ 0.920012] io scheduler noop registered > [ 0.920111] io scheduler anticipatory registered (default) > [ 0.920187] io scheduler deadline registered > [ 0.920346] io scheduler cfq registered > [ 0.958113] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ > sharing disabled > [ 0.962450] serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 3) is a 16550A > [ 2.871187] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 > blocksize > [ 2.961972] allocating ethernet device... > [ 3.010204] eth%d: using fifo mode. > [ 3.052064] eth%d: Xilinx EMAC #0 at 0x80400000 mapped to 0xC5000000, > irq=31 > [ 3.136606] eth%d: id 2.0a; block id 0, type 8 > [ 3.190431] Marvell 88E1101: Registered new driver > [ 3.250101] tun: Universal TUN/TAP device driver, 1.6 > [ 3.310712] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> > [ 3.385845] mice: PS/2 mouse device common for all mice > [ 3.448583] TCP bic registered > [ 3.485307] NET: Registered protocol family 1 > [ 3.537610] NET: Registered protocol family 17 > [ 4.096219] IP-Config: No network devices available. > [ 4.156871] RAMDISK: Compressed image found at block 0 > [ 5.002841] VFS: Mounted root (ext2 filesystem). > [ 5.058432] Freeing unused kernel memory: 84k init > ### Application running ... > > > BusyBox v(null) ((null)) Built-in shell (msh) > # > ------------------------------------------------------------------ > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > -- Dave Lynch DLA Systems Software Development: Embedded Linux 717.627.3770 dhlii@dlasys.net http://www.dlasys.net fax: 1.253.369.9244 Cell: 1.717.587.7774 Over 25 years' experience in platforms, languages, and technologies too numerous to list. "Any intelligent fool can make things bigger and more complex... It takes a touch of genius - and a lot of courage to move in the opposite direction." Albert Einstein ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2006-09-15 17:38 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <mailman.270.1158283233.2423.linuxppc-embedded@ozlabs.org>
2006-09-15 3:24 ` ethernet patch for kernel 2.6 for ml403 Aleck Lin
2006-09-15 11:17 ` David H. Lynch Jr.
2006-09-15 17:38 ` Aleck Lin
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.