From: "Berck E. Nash" <flyboy@gmail.com>
To: Tejun Heo <htejun@gmail.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: [PATCH] ahci: do not powerdown during initialization
Date: Fri, 24 Nov 2006 10:53:39 -0700 [thread overview]
Message-ID: <456731A3.8070807@gmail.com> (raw)
In-Reply-To: <20061120064236.GM2184@htj.dyndns.org>
Tejun Heo wrote:
> This patch moves power up/down out of port init/deinit and call them
> only when needed.
> ---
>
> Berck, can you please test this patch? This might fix your problem
> too. Jeff, this patch is necessary regardless of Berck's repsonse. I
> think this should go into #usptream-fixes too after some testing in
> #upstream (and in -mm).
Nope, that doesn't do it. All along I've also been getting weird
messages on system power-downs. I just now set up a serial console to
capture them. I dunno if they're of any significance, but they're on
the same device that pauses on boot, so perhaps they're related.
Berck
Will now halt.
[ 538.178188] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.191083] ata2.00: (irq_stat 0x40000001)
[ 538.199288] ata2.00: tag 0 cmd 0xe0 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.222873] ata2.00: configured for UDMA/133
[ 538.231432] ata2: EH complete
[ 538.237406] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.250289] ata2.00: (irq_stat 0x40000001)
[ 538.258497] ata2.00: tag 0 cmd 0xe0 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.282048] ata2.00: configured for UDMA/133
[ 538.290606] ata2: EH complete
[ 538.296580] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.309465] ata2.00: (irq_stat 0x40000001)
[ 538.317672] ata2.00: tag 0 cmd 0xe0 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.341206] ata2.00: configured for UDMA/133
[ 538.349764] ata2: EH complete
[ 538.355738] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.368621] ata2.00: (irq_stat 0x40000001)
[ 538.376834] ata2.00: tag 0 cmd 0xe0 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.400367] ata2.00: configured for UDMA/133
[ 538.408920] ata2: EH complete
[ 538.414894] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.427783] ata2.00: (irq_stat 0x40000001)
[ 538.435987] ata2.00: tag 0 cmd 0xe0 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.459528] ata2.00: configured for UDMA/133
[ 538.468077] ata2: EH complete
[ 538.474054] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.486941] ata2.00: (irq_stat 0x40000001)
[ 538.495144] ata2.00: tag 0 cmd 0xe0 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.518681] ata2.00: configured for UDMA/133
[ 538.527242] ata2: EH complete
[ 538.533219] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.546113] ata2.00: (irq_stat 0x40000001)
[ 538.554319] ata2.00: tag 0 cmd 0x94 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.577860] ata2.00: configured for UDMA/133
[ 538.586410] ata2: EH complete
[ 538.592387] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.605269] ata2.00: (irq_stat 0x40000001)
[ 538.613475] ata2.00: tag 0 cmd 0x94 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.637015] ata2.00: configured for UDMA/133
[ 538.645566] ata2: EH complete
[ 538.651540] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.664425] ata2.00: (irq_stat 0x40000001)
[ 538.672634] ata2.00: tag 0 cmd 0x94 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.696179] ata2.00: configured for UDMA/133
[ 538.704742] ata2: EH complete
[ 538.710716] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.723601] ata2.00: (irq_stat 0x40000001)
[ 538.731807] ata2.00: tag 0 cmd 0x94 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.755349] ata2.00: configured for UDMA/133
[ 538.763900] ata2: EH complete
[ 538.769873] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.782765] ata2.00: (irq_stat 0x40000001)
[ 538.790965] ata2.00: tag 0 cmd 0x94 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.814513] ata2.00: configured for UDMA/133
[ 538.823073] ata2: EH complete
[ 538.829047] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 538.841933] ata2.00: (irq_stat 0x40000001)
[ 538.850140] ata2.00: tag 0 cmd 0x94 Emask 0x1 stat 0x51 err 0x4
(device error)
[ 538.873679] ata2.00: configured for UDMA/133
[ 538.882233] ata2: EH complete
[ 538.888199] SCSI device sdd: 640 512-byte hdwr sectors (0 MB)
[ 538.890404] Synchronizing SCSI cache for disk sde:
[ 538.909477] sdd: Write Protect is off
[ 538.916822] SCSI device sdd: drive cache: write through
[ 538.927285] SCSI device sdd: 640 512-byte hdwr sectors (0 MB)
[ 538.938797] Synchronizing SCSI cache for disk sdc:
[ 538.948561] sdd: Write Protect is off
[ 538.949171] Synchronizing SCSI cache for disk sdb:
[ 538.949424] Synchronizing SCSI cache for disk sda:
[ 538.975451] SCSI device sdd: drive cache: write through
[ 539.441444] Shutdown: hdg
[ 539.446910] Shutdown: hde
[ 539.452716] Power down.
[ 539.457706] acpi_power_off called
next prev parent reply other threads:[~2006-11-24 17:53 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-20 6:42 [PATCH] ahci: do not powerdown during initialization Tejun Heo
2006-11-24 17:53 ` Berck E. Nash [this message]
2006-11-28 9:15 ` Jeff Garzik
2006-11-29 3:52 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=456731A3.8070807@gmail.com \
--to=flyboy@gmail.com \
--cc=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.