* eSATA errors
@ 2007-06-04 15:24 Tom Moore
0 siblings, 0 replies; only message in thread
From: Tom Moore @ 2007-06-04 15:24 UTC (permalink / raw)
To: linux-kernel
Hi
I have system running the 2.6.20 kernel, and I am trying to use an eSATA
disk with it. The hardware in question is a 'NexStar-3' eSATA
enclosure, and inside it is a Seagate Barracuda 7200.10 750Gb SATA drive.
I am hooking this up to an ASUS M2N-MX motherboard using the SATA to
eSATA bracket that comes with the enclosure.
When I boot up the machine the disk is recognized, but it immediately
has device errors and 'slow to respond' errors. When I use fdisk to
write a partition table it seems to give up entirely. Is this a known
problem, or is there something I can try?
I am not subscribed to the mailing list so I would appreciate a CC on
any replies.
Thanks,
Tom
Relevant lines from syslog...
Jun 3 15:33:57 fawkes Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
Jun 3 15:33:57 fawkes ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
Jun 3 15:33:57 fawkes NFORCE-MCP61: IDE controller at PCI slot 0000:00:06.0
Jun 3 15:33:57 fawkes NFORCE-MCP61: chipset revision 162
Jun 3 15:33:57 fawkes NFORCE-MCP61: not 100% native mode: will probe
irqs later
Jun 3 15:33:57 fawkes NFORCE-MCP61: BIOS didn't set cable bits
correctly. Enabling workaround.
Jun 3 15:33:57 fawkes NFORCE-MCP61: 0000:00:06.0 (rev a2) UDMA133
controller
Jun 3 15:33:57 fawkes ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings:
hda:DMA, hdb:pio
Jun 3 15:33:57 fawkes Probing IDE interface ide0...
Jun 3 15:33:57 fawkes hda: WDC WD2500JB-00GVA0, ATA DISK drive
Jun 3 15:33:57 fawkes ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jun 3 15:33:57 fawkes Probing IDE interface ide1...
Jun 3 15:33:57 fawkes hda: max request size: 512KiB
Jun 3 15:33:57 fawkes hda: 488397168 sectors (250059 MB) w/8192KiB
Cache, CHS=30401/255/63<6>hda: hw_config=604d
Jun 3 15:33:57 fawkes , UDMA(100)
Jun 3 15:33:57 fawkes hda: cache flushes supported
Jun 3 15:33:57 fawkes hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
Jun 3 15:33:57 fawkes 3ware Storage Controller device driver for Linux
v1.26.02.002.
Jun 3 15:33:57 fawkes sata_nv 0000:00:08.0: version 3.2
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 22
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt 0000:00:08.0[A] -> Link
[LSA0] -> GSI 22 (level, low) -> IRQ 18
Jun 3 15:33:57 fawkes PCI: Setting latency timer of device 0000:00:08.0
to 64
Jun 3 15:33:57 fawkes ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD082
bmdma 0xC880 irq 18
Jun 3 15:33:57 fawkes ata2: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02
bmdma 0xC888 irq 18
Jun 3 15:33:57 fawkes scsi0 : sata_nv
Jun 3 15:33:57 fawkes ata1: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Jun 3 15:33:57 fawkes ata1.00: ATA-7, max UDMA/133, 1465149168 sectors:
LBA48 NCQ (depth 0/32)
Jun 3 15:33:57 fawkes ata1.00: ata1: dev 0 multi count 16
Jun 3 15:33:57 fawkes ata1.00: configured for UDMA/133
Jun 3 15:33:57 fawkes scsi1 : sata_nv
Jun 3 15:33:57 fawkes ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Jun 3 15:33:57 fawkes ata2.00: ATA-7, max UDMA/133, 1465149168 sectors:
LBA48 NCQ (depth 0/32)
Jun 3 15:33:57 fawkes ata2.00: ata2: dev 0 multi count 16
Jun 3 15:33:57 fawkes ata2.00: configured for UDMA/133
Jun 3 15:33:57 fawkes scsi 0:0:0:0: Direct-Access ATA
ST3750640AS 3.AA PQ: 0 ANSI: 5
Jun 3 15:33:57 fawkes SCSI device sda: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sda: Write Protect is off
Jun 3 15:33:57 fawkes sda: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sda: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes SCSI device sda: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sda: Write Protect is off
Jun 3 15:33:57 fawkes sda: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sda: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes sda: sda1 sda2 sda3 sda4 < sda5 >
Jun 3 15:33:57 fawkes sd 0:0:0:0: Attached scsi disk sda
Jun 3 15:33:57 fawkes sd 0:0:0:0: Attached scsi generic sg0 type 0
Jun 3 15:33:57 fawkes scsi 1:0:0:0: Direct-Access ATA
ST3750640AS 3.AA PQ: 0 ANSI: 5
Jun 3 15:33:57 fawkes SCSI device sdb: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdb: Write Protect is off
Jun 3 15:33:57 fawkes sdb: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdb: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes SCSI device sdb: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdb: Write Protect is off
Jun 3 15:33:57 fawkes sdb: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdb: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes sdb: sdb1
Jun 3 15:33:57 fawkes sd 1:0:0:0: Attached scsi disk sdb
Jun 3 15:33:57 fawkes sd 1:0:0:0: Attached scsi generic sg1 type 0
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 21
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt 0000:00:08.1[B] -> Link
[LSA1] -> GSI 21 (level, low) -> IRQ 19
Jun 3 15:33:57 fawkes PCI: Setting latency timer of device 0000:00:08.1
to 64
Jun 3 15:33:57 fawkes ata3: SATA max UDMA/133 cmd 0xC800 ctl 0xC482
bmdma 0xC000 irq 19
Jun 3 15:33:57 fawkes ata4: SATA max UDMA/133 cmd 0xC400 ctl 0xC082
bmdma 0xC008 irq 19
Jun 3 15:33:57 fawkes scsi2 : sata_nv
Jun 3 15:33:57 fawkes ata3: port is slow to respond, please be patient
(Status 0xd0)
Jun 3 15:33:57 fawkes ata3: port failed to respond (30 secs, Status 0xd0)
Jun 3 15:33:57 fawkes ata3: SATA link up 3.0 Gbps (SStatus 123 SControl
300)
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ata3.00: ATA-7, max UDMA/133, 1465149168 sectors:
LBA48 NCQ (depth 0/32)
Jun 3 15:33:57 fawkes ata3.00: ata3: dev 0 multi count 16
Jun 3 15:33:57 fawkes ata3.00: Drive reports diagnostics failure. This
may indicate a drive
Jun 3 15:33:57 fawkes ata3.00: fault or invalid emulation. Contact
drive vendor for information.
Jun 3 15:33:57 fawkes ata3.00: configured for UDMA/133
Jun 3 15:33:57 fawkes scsi3 : sata_nv
Jun 3 15:33:57 fawkes ata4: SATA link down (SStatus 0 SControl 300)
Jun 3 15:33:57 fawkes ATA: abnormal status 0x7F on port 0xC407
Jun 3 15:33:57 fawkes scsi 2:0:0:0: Direct-Access ATA
ST3750640AS 3.AA PQ: 0 ANSI: 5
Jun 3 15:33:57 fawkes SCSI device sdc: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdc: Write Protect is off
Jun 3 15:33:57 fawkes sdc: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdc: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes SCSI device sdc: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdc: Write Protect is off
Jun 3 15:33:57 fawkes sdc: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdc: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes sdc: unknown partition table
Jun 3 15:33:57 fawkes sd 2:0:0:0: Attached scsi disk sdc
Jun 3 15:33:57 fawkes sd 2:0:0:0: Attached scsi generic sg2 type 0
later after trying to write new partition information...
Jun 3 15:35:58 fawkes ata3: port failed to respond (30 secs, Status 0xd0)
Jun 3 15:35:58 fawkes ata3: SATA link up 3.0 Gbps (SStatus 123 SControl
300)
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:36:28 fawkes ata3.00: qc timeout (cmd 0xec)
Jun 3 15:36:28 fawkes ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
Jun 3 15:36:28 fawkes ata3.00: revalidation failed (errno=-5)
Jun 3 15:36:28 fawkes ata3: failed to recover some devices, retrying in
5 secs
Jun 3 15:36:33 fawkes ata3: hard resetting port
Jun 3 15:36:40 fawkes ata3: port is slow to respond, please be patient
(Status 0xd0)
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2007-06-04 15:25 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-06-04 15:24 eSATA errors Tom Moore
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.