Re: 3ware 9650 tips

Re: 3ware 9650 tips

[Justin Piszcz]

On Fri, 13 Jul 2007, Joshua Baker-LePain wrote:

> My new system has a 3ware 9650SE-24M8 controller hooked to 24 500GB WD 
> drives.  The controller is set up as a RAID6 w/ a hot spare.  OS is CentOS 5 
> x86_64.  It's all running on a couple of Xeon 5130s on a Supermicro X7DBE 
> motherboard w/ 4GB of RAM.
>
> Trying to stick with a supported config as much as possible, I need to run 
> ext3.  As per usual, though, initial ext3 numbers are less than impressive. 
> Using bonnie++ to get a baseline, I get (after doing 'blockdev --setra 65536' 
> on the device):
> Write: 136MB/s
> Read:  384MB/s
>
> Proving it's not the hardware, with XFS the numbers look like:
> Write: 333MB/s
> Read:  465MB/s
>
> How many folks are using these?  Any tuning tips?
>
> Thanks.
>
> -- 
> Joshua Baker-LePain
> Department of Biomedical Engineering
> Duke University
>

Let's try that again with the right address :)


You are using HW RAID then?  Those numbers seem pretty awful for that
setup, including linux-raid@ even it though it appears you're running HW raid,
this is rather peculiar.

To give you an example I get 464MB/s write and 627MB/s with a 10 disk
raptor software raid5.

Justin.

Re: 3ware 9650 tips

[Jon Collette]

Wouldn't Raid 6 be slower than Raid 5 because of the extra fault tolerance?
    http://www.enterprisenetworksandservers.com/monthly/art.php?1754 - 
20% drop according to this article

His 500GB WD drives are 7200RPM compared to the Raptors 10K.  So his 
numbers will be slower. 

Justin what file system do you have running on the Raptors?  I think 
thats an interesting point made by Joshua.


Justin Piszcz wrote:
>
>
> On Fri, 13 Jul 2007, Joshua Baker-LePain wrote:
>
>> My new system has a 3ware 9650SE-24M8 controller hooked to 24 500GB 
>> WD drives.  The controller is set up as a RAID6 w/ a hot spare.  OS 
>> is CentOS 5 x86_64.  It's all running on a couple of Xeon 5130s on a 
>> Supermicro X7DBE motherboard w/ 4GB of RAM.
>>
>> Trying to stick with a supported config as much as possible, I need 
>> to run ext3.  As per usual, though, initial ext3 numbers are less 
>> than impressive. Using bonnie++ to get a baseline, I get (after doing 
>> 'blockdev --setra 65536' on the device):
>> Write: 136MB/s
>> Read:  384MB/s
>>
>> Proving it's not the hardware, with XFS the numbers look like:
>> Write: 333MB/s
>> Read:  465MB/s
>>
>> How many folks are using these?  Any tuning tips?
>>
>> Thanks.
>>
>> -- 
>> Joshua Baker-LePain
>> Department of Biomedical Engineering
>> Duke University
>>
>
> Let's try that again with the right address :)
>
>
> You are using HW RAID then?  Those numbers seem pretty awful for that
> setup, including linux-raid@ even it though it appears you're running 
> HW raid,
> this is rather peculiar.
>
> To give you an example I get 464MB/s write and 627MB/s with a 10 disk
> raptor software raid5.
>
> Justin.
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: 3ware 9650 tips

[Justin Piszcz]

On Fri, 13 Jul 2007, Jon Collette wrote:

> Wouldn't Raid 6 be slower than Raid 5 because of the extra fault tolerance?
>   http://www.enterprisenetworksandservers.com/monthly/art.php?1754 - 20% 
> drop according to this article
>
> His 500GB WD drives are 7200RPM compared to the Raptors 10K.  So his numbers 
> will be slower. 
> Justin what file system do you have running on the Raptors?  I think thats an 
> interesting point made by Joshua.

I use XFS:

Justin what file system do you have running on the Raptors?  I think thats 
an interesting point made by Joshua.

But I also run several 'optimations' for SW RAID and my overall 
configuration--  However, for the mkfs.xfs options, they auto-optimize for 
whatever (SW) raid I have them configured for.  Whereas if XFS cannot tell 
the disks/etc underneath the HW raid, I do not think the optimizations 
will be present(?)-- which menas you'd have to set the sunit and swidth 
appropriately.

>
>
> Justin Piszcz wrote:
>> 
>> 
>> On Fri, 13 Jul 2007, Joshua Baker-LePain wrote:
>> 
>>> My new system has a 3ware 9650SE-24M8 controller hooked to 24 500GB WD 
>>> drives.  The controller is set up as a RAID6 w/ a hot spare.  OS is CentOS 
>>> 5 x86_64.  It's all running on a couple of Xeon 5130s on a Supermicro 
>>> X7DBE motherboard w/ 4GB of RAM.
>>> 
>>> Trying to stick with a supported config as much as possible, I need to run 
>>> ext3.  As per usual, though, initial ext3 numbers are less than 
>>> impressive. Using bonnie++ to get a baseline, I get (after doing 'blockdev 
>>> --setra 65536' on the device):
>>> Write: 136MB/s
>>> Read:  384MB/s
>>> 
>>> Proving it's not the hardware, with XFS the numbers look like:
>>> Write: 333MB/s
>>> Read:  465MB/s
>>> 
>>> How many folks are using these?  Any tuning tips?
>>> 
>>> Thanks.
>>> 
>>> -- 
>>> Joshua Baker-LePain
>>> Department of Biomedical Engineering
>>> Duke University
>>> 
>> 
>> Let's try that again with the right address :)
>> 
>> 
>> You are using HW RAID then?  Those numbers seem pretty awful for that
>> setup, including linux-raid@ even it though it appears you're running HW 
>> raid,
>> this is rather peculiar.
>> 
>> To give you an example I get 464MB/s write and 627MB/s with a 10 disk
>> raptor software raid5.
>> 
>> Justin.
>> 
>> -
>> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>

Re: 3ware 9650 tips

[David Chinner]

On Fri, Jul 13, 2007 at 03:36:46PM -0400, Justin Piszcz wrote:
> On Fri, 13 Jul 2007, Jon Collette wrote:
> 
> >Wouldn't Raid 6 be slower than Raid 5 because of the extra fault tolerance?
> >  http://www.enterprisenetworksandservers.com/monthly/art.php?1754 - 20% 
> >drop according to this article
> >
> >His 500GB WD drives are 7200RPM compared to the Raptors 10K.  So his 
> >numbers will be slower. 
> >Justin what file system do you have running on the Raptors?  I think thats 
> >an interesting point made by Joshua.
> 
> I use XFS:

When it comes to bandwidth, there is good reason for that.

> >>>Trying to stick with a supported config as much as possible, I need to 
> >>>run ext3.  As per usual, though, initial ext3 numbers are less than 
> >>>impressive. Using bonnie++ to get a baseline, I get (after doing 
> >>>'blockdev --setra 65536' on the device):
> >>>Write: 136MB/s
> >>>Read:  384MB/s
> >>>
> >>>Proving it's not the hardware, with XFS the numbers look like:
> >>>Write: 333MB/s
> >>>Read:  465MB/s
> >>>

Those are pretty typical numbers. In my experience, ext3 is limited to about
250MB/s buffered write speed. It's not disk limited, it's design limited. e.g.
on a disk subsystem where XFS was getting 4-5GB/s buffered write, ext3 was doing
250MB/s.

http://oss.sgi.com/projects/xfs/papers/ols2006/ols-2006-paper.pdf

If you've got any sort of serious disk array, ext3 is not the filesystem
to use....

> >>>How many folks are using these?  Any tuning tips?

Make sure you tell XFS the correct sunit/swidth. For hardware
raid5/6, sunit = per-disk chunksize, swidth = number of *data* disks in
array.

Cheers,

Dave.
-- 
Dave Chinner
Principal Engineer
SGI Australian Software Group

Re: 3ware 9650 tips

[David Chinner]

On Mon, Jul 16, 2007 at 12:41:15PM +1000, David Chinner wrote:
> On Fri, Jul 13, 2007 at 03:36:46PM -0400, Justin Piszcz wrote:
> > On Fri, 13 Jul 2007, Jon Collette wrote:
> > 
> > >Wouldn't Raid 6 be slower than Raid 5 because of the extra fault tolerance?
> > >  http://www.enterprisenetworksandservers.com/monthly/art.php?1754 - 20% 
> > >drop according to this article
> > >
> > >His 500GB WD drives are 7200RPM compared to the Raptors 10K.  So his 
> > >numbers will be slower. 
> > >Justin what file system do you have running on the Raptors?  I think thats 
> > >an interesting point made by Joshua.
> > 
> > I use XFS:
> 
> When it comes to bandwidth, there is good reason for that.
> 
> > >>>Trying to stick with a supported config as much as possible, I need to 
> > >>>run ext3.  As per usual, though, initial ext3 numbers are less than 
> > >>>impressive. Using bonnie++ to get a baseline, I get (after doing 
> > >>>'blockdev --setra 65536' on the device):
> > >>>Write: 136MB/s
> > >>>Read:  384MB/s
> > >>>
> > >>>Proving it's not the hardware, with XFS the numbers look like:
> > >>>Write: 333MB/s
> > >>>Read:  465MB/s
> > >>>
> 
> Those are pretty typical numbers. In my experience, ext3 is limited to about
> 250MB/s buffered write speed. It's not disk limited, it's design limited. e.g.
> on a disk subsystem where XFS was getting 4-5GB/s buffered write, ext3 was doing
> 250MB/s.
> 
> http://oss.sgi.com/projects/xfs/papers/ols2006/ols-2006-paper.pdf
> 
> If you've got any sort of serious disk array, ext3 is not the filesystem
> to use....

To show what the difference is, I used blktrace and Chris Mason's
seekwatcher script on a simple, single threaded dd command on
a 12 disk dm RAID0 stripe:

# dd if=/dev/zero of=/mnt/scratch/fred bs=1024k count=10k; sync

http://oss.sgi.com/~dgc/writes/ext3_write.png
http://oss.sgi.com/~dgc/writes/xfs_write.png

You can see from the ext3 graph that it comes to a screeching halt
every 5s (probably when pdflush runs) and at all other times the
seek rate is >10,000 seeks/s. That's pretty bad for a brand new,
empty filesystem and the only way it is sustained is the fact that
the disks have their write caches turned on. ext4 will probably show
better results, but I haven't got any of the tools installed to be
able to test it....

The XFS pattern shows consistently an order of magnitude less seeks
and consistent throughput above 600MB/s. To put the number of seeks
in context, XFS is doing 512k I/Os at about 1200-1300 per second. The
number of seeks? A bit above 10^3 per second or roughly 1 seek per
I/O which is pretty much optimal.

Cheers,

Dave.

-- 
Dave Chinner
Principal Engineer
SGI Australian Software Group

Re: 3ware 9650 tips

[Bernd Schubert]

On Monday 16 July 2007 14:22:25 David Chinner wrote:
> You can see from the ext3 graph that it comes to a screeching halt
> every 5s (probably when pdflush runs) and at all other times the
> seek rate is >10,000 seeks/s. That's pretty bad for a brand new,
> empty filesystem and the only way it is sustained is the fact that
> the disks have their write caches turned on. ext4 will probably show
> better results, but I haven't got any of the tools installed to be
> able to test it....

I recently did some filesystem throuput tests, you may find it here

http://www.pci.uni-heidelberg.de/tc/usr/bernd/downloads/lustre/performance/

ldiskfs is ext3+extents+mballoc+some-smaller-patches, so is almost ext4 
(delayed allocation is still missing, but the clusterfs/lustre people didn't 
port it and I'm afraid of hard to detect filesystem corruptions if I include 
it myself).

Write performance is still slower than with xfs and I'm really considering to 
try to use xfs in lustre.

Cheers,
Bernd


-- 
Bernd Schubert
Q-Leap Networks GmbH

Re: 3ware 9650 tips

[Eric Sandeen]

David Chinner wrote:
> On Mon, Jul 16, 2007 at 12:41:15PM +1000, David Chinner wrote:
>> On Fri, Jul 13, 2007 at 03:36:46PM -0400, Justin Piszcz wrote:
...
>> If you've got any sort of serious disk array, ext3 is not the filesystem
>> to use....
> 
> To show what the difference is, I used blktrace and Chris Mason's
> seekwatcher script on a simple, single threaded dd command on
> a 12 disk dm RAID0 stripe:
> 
> # dd if=/dev/zero of=/mnt/scratch/fred bs=1024k count=10k; sync
> 
> http://oss.sgi.com/~dgc/writes/ext3_write.png
> http://oss.sgi.com/~dgc/writes/xfs_write.png

Were those all with default mkfs & mount options?  ext3 in writeback
mode might be an interesting comparison too.

-Eric

Re: 3ware 9650 tips

[David Chinner]

On Mon, Jul 16, 2007 at 10:50:34AM -0500, Eric Sandeen wrote:
> David Chinner wrote:
> > On Mon, Jul 16, 2007 at 12:41:15PM +1000, David Chinner wrote:
> >> On Fri, Jul 13, 2007 at 03:36:46PM -0400, Justin Piszcz wrote:
> ...
> >> If you've got any sort of serious disk array, ext3 is not the filesystem
> >> to use....
> > 
> > To show what the difference is, I used blktrace and Chris Mason's
> > seekwatcher script on a simple, single threaded dd command on
> > a 12 disk dm RAID0 stripe:
> > 
> > # dd if=/dev/zero of=/mnt/scratch/fred bs=1024k count=10k; sync
> > 
> > http://oss.sgi.com/~dgc/writes/ext3_write.png
> > http://oss.sgi.com/~dgc/writes/xfs_write.png
> 
> Were those all with default mkfs & mount options?  ext3 in writeback
> mode might be an interesting comparison too.

Defaults. i.e.

# mkfs.ext3 /dev/mapper/dm0

# mkfs.xfs /dev/mapper/dm0

The mkfs.xfs picked up sunit/swidth correctly from the dm volume.

Last time I checked, writeback made little difference to ext3 throughput;
maybe 5-10% at most. I'll run it again later today...

Cheers,

Dave.
-- 
Dave Chinner
Principal Engineer
SGI Australian Software Group

Re: 3ware 9650 tips

[Joshua Baker-LePain]

On Mon, 16 Jul 2007 at 12:41pm, David Chinner wrote

> If you've got any sort of serious disk array, ext3 is not the filesystem
> to use....

I do so wish that RedHat shared this view...

-- 
Joshua Baker-LePain
Department of Biomedical Engineering
Duke University

[Advocacy] Re: 3ware 9650 tips

[Bryan J. Smith]

Off-topic, advocacy-level response ...  

On Mon, 2007-07-16 at 11:43 -0400, Joshua Baker-LePain wrote:
> I do so wish that RedHat shared this view...

I've been trying to convince them since Red Hat Linux 7 (and, later, 9)
that they need to realize the limits of Ext3 at the enterprise end of
the scalability spectrum -- you know, that whole market they are
seemingly saying they are the king of and a replacement for Sun?  ;->

The problem with Red Hat is that when anyone brings up an alternative to
Ext3, Red Hat falls back to arguments against other filesystems, which
is rather easy given the various compatibility issues with JFS (ported
from OS/2, requiring a lot of inode compatibility hacks -- don't get me
started with my experiences) and ReiserFS (utter lack of inode
compatibility in structures, requiring kernel-level emulation, etc...
that never seems to work, regardless of what the advocates say, let
alone the almsota always "out-of-sync" off-line repair tools).

But when you bring up XFS and its history of a stable, but advanced
inode structure, quota support from day 1, POSIX ACLs from nearly day 1,
and all the SGI team put into 2.5.3+ that is now stock kernel, they
still try to dance.  One thing I always get is "oh, its extents don't
perform well for /tmp or /var" or countless other arguments, of which I
merely respond, "all the more reason to use Ext3 for those few
filesystems, and XFS when Ext3 doesn't scale -- like for
large /home, /export, etc... filesystems."  No matter how many times I
put forth the argument that XFS complements Ext3, they seem to treat it
as yet another JFS/ReiserFS argument.

Hopeless?

-- Bryan "one of the reasons I still deploy Solaris instead of RHEL for
fileservers, even though RHL7+XFS and RHL9+XFS rocked (and are still
rocking!)" Smith


-- 
Bryan J. Smith         Professional, Technical Annoyance
mailto:b.j.smith@ieee.org   http://thebs413.blogspot.com
--------------------------------------------------------
        Fission Power:  An Inconvenient Solution

Re: [Advocacy] Re: 3ware 9650 tips

[Al Boldi]

Bryan J. Smith wrote:
> Off-topic, advocacy-level response ...
>
> On Mon, 2007-07-16 at 11:43 -0400, Joshua Baker-LePain wrote:
> > I do so wish that RedHat shared this view...
>
> I've been trying to convince them since Red Hat Linux 7 (and, later, 9)
> that they need to realize the limits of Ext3 at the enterprise end of
> the scalability spectrum -- you know, that whole market they are
> seemingly saying they are the king of and a replacement for Sun?  ;->
>
> The problem with Red Hat is that when anyone brings up an alternative to
> Ext3, Red Hat falls back to arguments against other filesystems, which
> is rather easy given the various compatibility issues with JFS (ported
> from OS/2, requiring a lot of inode compatibility hacks -- don't get me
> started with my experiences) and ReiserFS (utter lack of inode
> compatibility in structures, requiring kernel-level emulation, etc...
> that never seems to work, regardless of what the advocates say, let
> alone the almsota always "out-of-sync" off-line repair tools).
>
> But when you bring up XFS and its history of a stable, but advanced
> inode structure, quota support from day 1, POSIX ACLs from nearly day 1,
> and all the SGI team put into 2.5.3+ that is now stock kernel, they
> still try to dance.  One thing I always get is "oh, its extents don't
> perform well for /tmp or /var" or countless other arguments, of which I
> merely respond, "all the more reason to use Ext3 for those few
> filesystems, and XFS when Ext3 doesn't scale -- like for
> large /home, /export, etc... filesystems."  No matter how many times I
> put forth the argument that XFS complements Ext3, they seem to treat it
> as yet another JFS/ReiserFS argument.
>
> Hopeless?
>
> -- Bryan "one of the reasons I still deploy Solaris instead of RHEL for
> fileservers, even though RHL7+XFS and RHL9+XFS rocked (and are still
> rocking!)" Smith

XFS surely rocks, but it's missing one critical component: data=ordered
And that's one component that's just too critical to overlook for an 
enterprise environment that is built on data-integrity over performance.

So that's the secret why people still use ext3, and XFS' reliance on external 
hardware to ensure integrity is really misplaced.

Now, maybe when we get the data=ordered onto the VFS level, then maybe XFS 
may become viable for the enterprise, and ext3 may cease to be KING.


Thanks!

--
Al

Re: [Advocacy] Re: 3ware 9650 tips

[Matthew Wilcox]

On Mon, Jul 16, 2007 at 08:40:00PM +0300, Al Boldi wrote:
> XFS surely rocks, but it's missing one critical component: data=ordered
> And that's one component that's just too critical to overlook for an 
> enterprise environment that is built on data-integrity over performance.
> 
> So that's the secret why people still use ext3, and XFS' reliance on external 
> hardware to ensure integrity is really misplaced.
> 
> Now, maybe when we get the data=ordered onto the VFS level, then maybe XFS 
> may become viable for the enterprise, and ext3 may cease to be KING.

Wow, thanks for bringing an advocacy thread onto linux-fsdevel.  Just what
we wanted.  Do you have any insight into how to "get the data=ordered
onto the VFS level"?  Because to me, that sounds like pure nonsense.

-- 
"Bill, look, we understand that you're interested in selling us this
operating system, but compare it to ours.  We can't possibly take such
a retrograde step."

[RFC] VFS: data=ordered (was: [Advocacy] Re: 3ware 9650 tips)

[Al Boldi]

Matthew Wilcox wrote:
> On Mon, Jul 16, 2007 at 08:40:00PM +0300, Al Boldi wrote:
> > XFS surely rocks, but it's missing one critical component: data=ordered
> > And that's one component that's just too critical to overlook for an
> > enterprise environment that is built on data-integrity over performance.
> >
> > So that's the secret why people still use ext3, and XFS' reliance on
> > external hardware to ensure integrity is really misplaced.
> >
> > Now, maybe when we get the data=ordered onto the VFS level, then maybe
> > XFS may become viable for the enterprise, and ext3 may cease to be KING.
>
> Wow, thanks for bringing an advocacy thread onto linux-fsdevel.  Just what
> we wanted.  Do you have any insight into how to "get the data=ordered
> onto the VFS level"?  Because to me, that sounds like pure nonsense.

Well, conceptually it sounds like a piece of cake, technically your guess is 
as good as mine.  IIRC, akpm once mentioned something like this.

But seriously, can you think of a technical reason why it shouldn't be 
possible to abstract data=ordered mode out into the VFS?


Thanks!

--
Al

Re: [RFC] VFS: data=ordered (was: [Advocacy] Re: 3ware 9650 tips)

[Matthew Wilcox]

On Mon, Jul 16, 2007 at 09:28:08PM +0300, Al Boldi wrote:
> Well, conceptually it sounds like a piece of cake, technically your guess is 
> as good as mine.  IIRC, akpm once mentioned something like this.

How much have you looked at the VFS?  There's nothing journalling-related
in the VFS right now.  ext3 and XFS share no common journalling code,
nor do I think that would be possible, due to the very different concepts
they have of journalling.

Here's a good hint:

$ find fs -type f |xargs grep -l journal_start
fs/ext3/acl.c
fs/ext3/inode.c
fs/ext3/ioctl.c
fs/ext3/namei.c
fs/ext3/resize.c
fs/ext3/super.c
fs/ext3/xattr.c
fs/ext4/acl.c
fs/ext4/extents.c
fs/ext4/inode.c
fs/ext4/ioctl.c
fs/ext4/namei.c
fs/ext4/resize.c
fs/ext4/super.c
fs/ext4/xattr.c
fs/jbd/journal.c
fs/jbd/transaction.c
fs/jbd2/journal.c
fs/jbd2/transaction.c
fs/ocfs2/journal.c
fs/ocfs2/super.c

JBD and JBD2 provide a journalling implementation that ext3, ext4 and
ocfs2 use.  Note that XFS doesn't, it has its own journalling code.

If you want XFS to support data=ordered, talk to the XFS folks.  Or
start picking through XFS yourself, of course -- you do have the source
code.

-- 
"Bill, look, we understand that you're interested in selling us this
operating system, but compare it to ours.  We can't possibly take such
a retrograde step."

Re: [Advocacy] Re: 3ware 9650 tips

[Bryan J. Smith]

On Mon, 2007-07-16 at 11:48 -0600, Matthew Wilcox wrote:
> Wow, thanks for bringing an advocacy thread onto linux-fsdevel.  Just what
> we wanted.  Do you have any insight into how to "get the data=ordered
> onto the VFS level"?  Because to me, that sounds like pure nonsense.

First off, I have no idea who decided to respond to my post and CC:
linux-fsdevel on it.

In retrospect, secondly, I should have not posted my post to linux-raid
in the first place (is that list now mirrored to linux-fsdevel or
something?).  I was just sharing in my frustration of the lack of XFS
support by Red Hat.

So, lastly and in any case, my apologies to all, even if I did not
proliferate it to linux-fsdevel, it was probably not ideal for me to
post such to anything on vger.kernel.org (like linux-raid) in the first
place.


-- 
Bryan J. Smith         Professional, Technical Annoyance
mailto:b.j.smith@ieee.org   http://thebs413.blogspot.com
--------------------------------------------------------
        Fission Power:  An Inconvenient Solution

Re: 3ware 9650 tips

[Stuart Levy]

On Mon, Jul 16, 2007 at 11:43:24AM -0400, Joshua Baker-LePain wrote:
> On Mon, 16 Jul 2007 at 12:41pm, David Chinner wrote
> 
> >If you've got any sort of serious disk array, ext3 is not the filesystem
> >to use....
> 
> I do so wish that RedHat shared this view...

So they support XFS in Fedora, but not in RHEL??
(I've been using Fedora...)

[Advocacy] Re: 3ware 9650 tips

[Bryan J. Smith]

[ I removed linux-raid, the only vgers list I posted to (who
re-posted/responded to my post on linux-fsdevel anyway?), from this
response. ]

On Mon, 2007-07-16 at 12:34 -0500, Stuart Levy wrote:
> So they support XFS in Fedora, but not in RHEL??
> (I've been using Fedora...)

Fedora ships support for all filesystems, and I believe has since Fedora
Core 2 / kernel 2.6.  RHEL only ships with support for Ext3.

There are various support issues with XFS that I, among others, feel
could be quickly addressed if Red Hat took a keen interest in supporting
XFS as a second, supplemental filesystem to Ext3.  I have gone on-record
several times about this, although I've dropped the advocacy over the
last few years and just "given up."  I honestly haven't kept up with the
issues either (like issues with XFS and the 4G/4G kernel model and/or
4KiB stacks -- have they been addressed?).

Luckily I have been doing more and more embedded as of late, so I
haven't had to deploy large filesystems.  But I have put in a few
Solaris 10/Opteron systems as NFS/SMB file server solutions in the last
year.  I'm not saying Solaris is "better," I'm just saying I would
really like RHEL Ext3 with an officially supported XFS release.  That's
all.


-- 
Bryan J. Smith         Professional, Technical Annoyance
mailto:b.j.smith@ieee.org   http://thebs413.blogspot.com
--------------------------------------------------------
        Fission Power:  An Inconvenient Solution

Re: [Advocacy] Re: 3ware 9650 tips

[Simon Matter]

> [ I removed linux-raid, the only vgers list I posted to (who
> re-posted/responded to my post on linux-fsdevel anyway?), from this
> response. ]
>
> On Mon, 2007-07-16 at 12:34 -0500, Stuart Levy wrote:
>> So they support XFS in Fedora, but not in RHEL??
>> (I've been using Fedora...)
>
> Fedora ships support for all filesystems, and I believe has since Fedora
> Core 2 / kernel 2.6.  RHEL only ships with support for Ext3.
>
> There are various support issues with XFS that I, among others, feel
> could be quickly addressed if Red Hat took a keen interest in supporting
> XFS as a second, supplemental filesystem to Ext3.  I have gone on-record
> several times about this, although I've dropped the advocacy over the
> last few years and just "given up."  I honestly haven't kept up with the
> issues either (like issues with XFS and the 4G/4G kernel model and/or
> 4KiB stacks -- have they been addressed?).

I already wrote quite a long mail for this list yesterday but then decided
not to send it because I also gave up on the issue with RedHat. It has all
been said in the past years and it's still true: You can't compare
anything with XFS on Linux and the competitiors aren't sleeping (just
think ZFS for example). I know that XFS had and maybe still has some minor
issues - but, if RedHat decided to use XFS and put the same effort into it
like they did with Ext3, those problems would have gone long ago.
I'm a long time XFS user starting with RedHat 7.x, and I'm still using it
for choosen filesystem on RHEL3,4,5. I just don't want to live without
lvextend and xfs_growfs.

Simon

Re: 3ware 9650 tips

[Joshua Baker-LePain]

On Fri, 13 Jul 2007 at 2:35pm, Justin Piszcz wrote

> On Fri, 13 Jul 2007, Joshua Baker-LePain wrote:
>
>> My new system has a 3ware 9650SE-24M8 controller hooked to 24 500GB WD 
>> drives.  The controller is set up as a RAID6 w/ a hot spare.  OS is CentOS 
>> 5 x86_64.  It's all running on a couple of Xeon 5130s on a Supermicro X7DBE 
>> motherboard w/ 4GB of RAM.
>> 
>> Trying to stick with a supported config as much as possible, I need to run 
>> ext3.  As per usual, though, initial ext3 numbers are less than impressive. 
>> Using bonnie++ to get a baseline, I get (after doing 'blockdev --setra 
>> 65536' on the device):
>> Write: 136MB/s
>> Read:  384MB/s
>> 
>> Proving it's not the hardware, with XFS the numbers look like:
>> Write: 333MB/s
>> Read:  465MB/s
>> 
>> How many folks are using these?  Any tuning tips?
>> 
>> Thanks.
>
> You are using HW RAID then?  Those numbers seem pretty awful for that
> setup, including linux-raid@ even it though it appears you're running HW 
> raid,
> this is rather peculiar.

Yep, hardware RAID -- I need the hot swappability (which, AFAIK, is still 
an issue with md).

-- 
Joshua Baker-LePain
Department of Biomedical Engineering
Duke University

Re: 3ware 9650 tips

[Michael Tokarev]

Joshua Baker-LePain wrote:
[]
> Yep, hardware RAID -- I need the hot swappability (which, AFAIK, is
> still an issue with md).

Just out of curiocity - what do you mean by "swappability" ?

For many years we're using linux software raid, we had no problems
with "swappability" of the component drives (in case of drive
failures and what not).  With non-hotswappable drives (old scsi
and ide ones), rebooting is needed for the system to recognize the
drives.  For modern sas/sata drives, i can replace a faulty drive
without anyone noticing...  Maybe you're referring to something
else?

Thanks.

/mjt

Re: 3ware 9650 tips

[Andrew Klaassen]

--- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:

> To give you an example I get 464MB/s write and
> 627MB/s with a 10 disk
> raptor software raid5.

Is that with the 9650?

Andrew





      ____________________________________________________________________________________
Fussy? Opinionated? Impossible to please? Perfect.  Join Yahoo!'s user panel and lay it on us. http://surveylink.yahoo.com/gmrs/yahoo_panel_invite.asp?a=7 

Re: 3ware 9650 tips

[Justin Piszcz]

On Fri, 13 Jul 2007, Andrew Klaassen wrote:

> --- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:
>
>> To give you an example I get 464MB/s write and
>> 627MB/s with a 10 disk
>> raptor software raid5.
>
> Is that with the 9650?
>
> Andrew
>
>

Sorry no, its with software raid 5 and the 965 chipset + three SATA PCI-e 
cards.

Justin.

Re: 3ware 9650 tips

[Andrew Klaassen]

--- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:

> 
> 
> On Fri, 13 Jul 2007, Andrew Klaassen wrote:
> 
> > --- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:
> >
> >> To give you an example I get 464MB/s write and
> >> 627MB/s with a 10 disk
> >> raptor software raid5.
> >
> > Is that with the 9650?
> >
> > Andrew
> >
> >
> 
> Sorry no, its with software raid 5 and the 965
> chipset + three SATA PCI-e 
> cards.

Which cards?  Those are pretty good numbers, so I'm
interested.

Andrew





 
____________________________________________________________________________________
Never miss an email again!
Yahoo! Toolbar alerts you the instant new Mail arrives.
http://tools.search.yahoo.com/toolbar/features/mail/

Re: 3ware 9650 tips

[Justin Piszcz]

On Sat, 14 Jul 2007, Andrew Klaassen wrote:

> --- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:
>
>>
>>
>> On Fri, 13 Jul 2007, Andrew Klaassen wrote:
>>
>>> --- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:
>>>
>>>> To give you an example I get 464MB/s write and
>>>> 627MB/s with a 10 disk
>>>> raptor software raid5.
>>>
>>> Is that with the 9650?
>>>
>>> Andrew
>>>
>>>
>>
>> Sorry no, its with software raid 5 and the 965
>> chipset + three SATA PCI-e
>> cards.
>
> Which cards?  Those are pretty good numbers, so I'm
> interested.
>
> Andrew

03:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid 
II Controller (rev 01)

$19.99 2 port SYBA cards (Silicon Image 3132s)

http://www.directron.com/sdsa2pex2ir.html

Re: 3ware 9650 tips

[Andrew Klaassen]

--- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:

> 03:00.0 RAID bus controller: Silicon Image, Inc. SiI
> 3132 Serial ATA Raid 
> II Controller (rev 01)
> 
> $19.99 2 port SYBA cards (Silicon Image 3132s)
> 
> http://www.directron.com/sdsa2pex2ir.html

Cool, thanks.

What are your bonnie++ rewrite numbers?

Andrew




       
____________________________________________________________________________________
Be a better Globetrotter. Get better travel answers from someone who knows. Yahoo! Answers - Check it out.
http://answers.yahoo.com/dir/?link=list&sid=396545469

Re: 3ware 9650 tips

[Justin Piszcz]

On Sat, 14 Jul 2007, Andrew Klaassen wrote:

> --- Justin Piszcz <jpiszcz@lucidpixels.com> wrote:
>
>> 03:00.0 RAID bus controller: Silicon Image, Inc. SiI
>> 3132 Serial ATA Raid
>> II Controller (rev 01)
>>
>> $19.99 2 port SYBA cards (Silicon Image 3132s)
>>
>> http://www.directron.com/sdsa2pex2ir.html
>
> Cool, thanks.
>
> What are your bonnie++ rewrite numbers?
>
> Andrew

3 runs:
p34,16G,77169,99,413276,80,155348,26,78932,99,535482,41,607.0,0,16:100000:16/64,1500,12,4886,15,1790,16,1821,17,6081,19,2159,19
p34,16G,77659,99,451593,87,167267,28,79058,99,584310,45,613.1,0,16:100000:16/64,1843,15,6006,31,1325,11,1204,12,3629,12,3324,31
p34,16G,77873,99,441881,87,166384,28,75182,99,566384,43,619.4,0,16:100000:16/64,1537,13,4474,15,1827,18,880,8,7658,22,3864,36

avg: 
p34,16G,77567,99,435583,84.6667,163000,27.3333,77724,99,562059,43,613.167,0,16:100000:16/64,1626.67,13.3333,5122,20.3333,1647.33,15,1301.67,12.3333,5789.33,17.6667,3115.67,28.6667

rewrite:
163000 KiB/s

When tarring 4.4GB (of backup files) it takes about 20 seconds on XFS.

Seems to vary as I change my configuration a lot:

Here is from a while back:

Version  1.03       ------Sequential Output------ --Sequential Input- 
--Random-
                     -Per Chr- --Block-- -Rewrite- -Per Chr- --Block-- 
--Seeks--
Machine        Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP 
/sec %CP
p34-raid5    15696M 73755  99 411445  75 198639  34 78721  99 483169  39 
584.8   0
                     ------Sequential Create------ --------Random 
Create--------

p34-raid5,15696M,73755,99,411445,75,198639,34,78721,99,483169,39,584.8,0,16:100000:16/64,919,8,9940,28,2841,18,922,8,3225,10,2422,18


Justin.

Re: 3ware 9650 tips

[Mikael Abrahamsson]

On Fri, 13 Jul 2007, Justin Piszcz wrote:

> You are using HW RAID then?  Those numbers seem pretty awful for that 
> setup, including linux-raid@ even it though it appears you're running HW 
> raid, this is rather peculiar.

No, it has been discussed numerous times on this list.

SW raid is faster because it has access to (often) gigabytes of block 
cache, which the HW raid controller doesn't have. SW raid is therefore 
able to avoid a lot of reads when it needs to write, speeding things up 
considerably.

I always use 3ware HW-raid though as I consider it more reliable. Since 
most of my access is "write once, read many" write speed isn't as 
important to me as data integrity.

Take your 3ware HW-raid, do a dd (read or write) to the device and see it 
being very quick (because it can fit all the data into its cache as it 
either reads or writes), then put a filesystem on it and do writes there, 
especially journaled writes, and see write speed go down to 1/10 or so.

-- 
Mikael Abrahamsson    email: swmike@swm.pp.se

Re: 3ware 9650 tips

[Andrew Klaassen]

--- Mikael Abrahamsson <swmike@swm.pp.se> wrote:

> Take your 3ware HW-raid, do a dd (read or write) to
> the device and see it 
> being very quick (because it can fit all the data
> into its cache as it 
> either reads or writes), then put a filesystem on it
> and do writes there, 
> especially journaled writes, and see write speed go
> down to 1/10 or so.

How does non-cached performance tend to compare?

Andrew





       
____________________________________________________________________________________
Looking for a deal? Find great prices on flights and hotels with Yahoo! FareChase.
http://farechase.yahoo.com/