* Fwd: Intel 82801G (ICH7) SATA port reset
[not found] <6b9952490708260411g22dede8ew6549acf0436b6e2e@mail.gmail.com>
@ 2007-08-26 11:14 ` Joris
2007-09-08 7:34 ` Tejun Heo
0 siblings, 1 reply; 2+ messages in thread
From: Joris @ 2007-08-26 11:14 UTC (permalink / raw)
To: linux-ide
[-- Attachment #1: Type: text/plain, Size: 1855 bytes --]
Hello List,
I have a rather annoying problem.
On an Intel S3000AHLX
(http://www.intel.com/design/servers/boards/s3000ah/index.htm)
motherboard, I can't seem to utilize all SATA interfaces to the
maximum.
The first sata interface frequently resets every few seconds under
heavy IO, the net result being ridiculous slow transfers (attach:
dmesg_random_collection_of_errors)
Running debian unstable and it's version of 2.6.22. System contains a
xeon 3210 and an adaptec scsi controller from which I currently boot.
There is little logic in the symptoms:
* if there is no or light IO, no resets occur.
* it's always the sda port that resets (changing cables or disks
doesn't make a difference).
* only specific combinations of disk-usage on the sata disks (attach:
disk_combinations_causing_reset), just using sda alone does not cause
resets.
* reading is enough, writing is (subjectively) worse. dd
if=/dev/sd{a,b,c,d} of=/dev/null & guarantees trouble.
* when the port resets, the disk makes a clearly audible clicking noise
I tried numerous things:
* having the board exchanged with intel for the latest revision
(thanks to my hardware supplier), updating to the latest bios and to a
bios version 6 months old.
* booting with older versions of the linux kernel, 2.6.18 and 2.6.21.
* Using all possible combinations of the bios' matrix/lsi fakeraid and
non-raid modes (always ignoring the "raid" and using the disks
directly), and enable/disable the one PATA port in the bios.
* asked seagate for a drive firmware update, to no avail.
The only workable solution so far is to leave the first sata interface
unused (remove the disk), which is obviously not a very nice solution.
Any hints or suggestions would be welcome, I'd be more than happy to
try out new things.
things. I'm a bit at a loss on how to proceed at the moment.
Kind regards,
Joris
[-- Attachment #2: bootmessages --]
[-- Type: application/octet-stream, Size: 124480 bytes --]
Aug 24 04:44:55 tempname syslogd 1.4.1#20: restart.
Aug 24 04:44:55 tempname kernel: klogd 1.4.1#20, log source = /proc/kmsg started.
Aug 24 04:44:55 tempname kernel: Linux version 2.6.22-1-amd64 (Debian 2.6.22-2) (waldi@debian.org) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14)) #1 SMP Mon Jul 23 12:43:14 UTC 2007
Aug 24 04:44:55 tempname kernel: Command line: root=LABEL=soloscsi ro
Aug 24 04:44:55 tempname kernel: BIOS-provided physical RAM map:
Aug 24 04:44:55 tempname kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 000000000009d400 - 0000000000100000 (reserved)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 0000000000100000 - 00000000dfc0e000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfc0e000 - 00000000dfc5f000 (reserved)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfc5f000 - 00000000dfce6000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfce6000 - 00000000dfedf000 (ACPI NVS)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfedf000 - 00000000dfeed000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfeed000 - 00000000dfeff000 (ACPI data)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000dfeff000 - 00000000dff00000 (usable)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 00000000fffc0000 - 00000000fffd0000 (reserved)
Aug 24 04:44:55 tempname kernel: BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Aug 24 04:44:55 tempname kernel: end_pfn_map = 1179648
Aug 24 04:44:55 tempname kernel: DMI 2.4 present.
Aug 24 04:44:55 tempname kernel: ACPI: RSDP 000F0350, 0024 (r2 INTEL )
Aug 24 04:44:55 tempname kernel: ACPI: XSDT DFEFE120, 0074 (r1 INTEL S3000AHX 0 INTL 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: FACP DFEFB000, 00F4 (r3 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: DSDT DFEF6000, 4922 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: FACS DFE71000, 0040
Aug 24 04:44:55 tempname kernel: ACPI: APIC DFEF5000, 0084 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: WDDT DFEF4000, 0040 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: MCFG DFEF3000, 003C (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: ASF! DFEF2000, 009F (r32 INTEL S3000AHX 1 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEF1000, 0175 (r1 INTEL Cpu0Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEF0000, 0175 (r1 INTEL Cpu1Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEEF000, 0175 (r1 INTEL Cpu2Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEEE000, 0175 (r1 INTEL Cpu3Ist 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: ACPI: SSDT DFEED000, 01BC (r1 INTEL CpuPm 10 MSFT 1000013)
Aug 24 04:44:55 tempname kernel: No NUMA configuration found
Aug 24 04:44:55 tempname kernel: Faking a node at 0000000000000000-0000000120000000
Aug 24 04:44:55 tempname kernel: Bootmem setup node 0 0000000000000000-0000000120000000
Aug 24 04:44:55 tempname kernel: Zone PFN ranges:
Aug 24 04:44:55 tempname kernel: DMA 0 -> 4096
Aug 24 04:44:55 tempname kernel: DMA32 4096 -> 1048576
Aug 24 04:44:55 tempname kernel: Normal 1048576 -> 1179648
Aug 24 04:44:55 tempname kernel: early_node_map[6] active PFN ranges
Aug 24 04:44:55 tempname kernel: 0: 0 -> 157
Aug 24 04:44:55 tempname kernel: 0: 256 -> 916494
Aug 24 04:44:55 tempname kernel: 0: 916575 -> 916710
Aug 24 04:44:55 tempname kernel: 0: 917215 -> 917229
Aug 24 04:44:55 tempname kernel: 0: 917247 -> 917248
Aug 24 04:44:55 tempname kernel: 0: 1048576 -> 1179648
Aug 24 04:44:55 tempname kernel: ACPI: PM-Timer IO Port: 0x408
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Aug 24 04:44:55 tempname kernel: Processor #0 (Bootup-CPU)
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Aug 24 04:44:55 tempname kernel: Processor #2
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Aug 24 04:44:55 tempname kernel: Processor #1
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Aug 24 04:44:55 tempname kernel: Processor #3
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
Aug 24 04:44:55 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Aug 24 04:44:55 tempname kernel: ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
Aug 24 04:44:55 tempname kernel: IOAPIC[0]: apic_id 5, address 0xfec00000, GSI 0-23
Aug 24 04:44:55 tempname kernel: ACPI: IOAPIC (id[0x06] address[0xfec10000] gsi_base[30])
Aug 24 04:44:55 tempname kernel: IOAPIC[1]: apic_id 6, address 0xfec10000, GSI 30-53
Aug 24 04:44:55 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Aug 24 04:44:55 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Aug 24 04:44:55 tempname kernel: Setting APIC routing to flat
Aug 24 04:44:55 tempname kernel: Using ACPI (MADT) for SMP configuration information
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 000000000009e000 - 0000000000100000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dfc0e000 - 00000000dfc5f000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dfce6000 - 00000000dfedf000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dfeed000 - 00000000dfeff000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000dff00000 - 00000000fffc0000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000fffc0000 - 00000000fffd0000
Aug 24 04:44:55 tempname kernel: swsusp: Registered nosave memory region: 00000000fffd0000 - 0000000100000000
Aug 24 04:44:55 tempname kernel: Allocating PCI resources starting at e0000000 (gap: dff00000:200c0000)
Aug 24 04:44:55 tempname kernel: SMP: Allowing 4 CPUs, 0 hotplug CPUs
Aug 24 04:44:55 tempname kernel: PERCPU: Allocating 37896 bytes of per cpu data
Aug 24 04:44:55 tempname kernel: Built 1 zonelists. Total pages: 1030465
Aug 24 04:44:55 tempname kernel: Kernel command line: root=LABEL=soloscsi ro
Aug 24 04:44:55 tempname kernel: Initializing CPU#0
Aug 24 04:44:55 tempname kernel: PID hash table entries: 4096 (order: 12, 32768 bytes)
Aug 24 04:44:55 tempname kernel: time.c: Detected 2133.467 MHz processor.
Aug 24 04:44:55 tempname kernel: Console: colour VGA+ 80x25
Aug 24 04:44:55 tempname kernel: Checking aperture...
Aug 24 04:44:55 tempname kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Aug 24 04:44:55 tempname kernel: Placing software IO TLB between 0x1050000 - 0x5050000
Aug 24 04:44:55 tempname kernel: Memory: 4049736k/4718592k available (2009k kernel code, 140732k reserved, 946k data, 296k init)
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4270.08 BogoMIPS (lpj=8540176)
Aug 24 04:44:55 tempname kernel: Security Framework v1.0.0 initialized
Aug 24 04:44:55 tempname kernel: SELinux: Disabled at boot.
Aug 24 04:44:55 tempname kernel: Capability LSM initialized
Aug 24 04:44:55 tempname kernel: Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Aug 24 04:44:55 tempname kernel: Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Aug 24 04:44:55 tempname kernel: Mount-cache hash table entries: 256
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 0/0 -> Node 0
Aug 24 04:44:55 tempname kernel: using mwait in idle threads.
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 0
Aug 24 04:44:55 tempname kernel: CPU0: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to UP code
Aug 24 04:44:55 tempname kernel: ACPI: Core revision 20070126
Aug 24 04:44:55 tempname kernel: Using local APIC timer interrupts.
Aug 24 04:44:55 tempname kernel: result 16667710
Aug 24 04:44:55 tempname kernel: Detected 16.667 MHz APIC timer.
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:44:55 tempname kernel: Booting processor 1/4 APIC 0x2
Aug 24 04:44:55 tempname kernel: Initializing CPU#1
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4267.16 BogoMIPS (lpj=8534335)
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 1/2 -> Node 0
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 2
Aug 24 04:44:55 tempname kernel: CPU1: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:44:55 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:44:55 tempname kernel: Booting processor 2/4 APIC 0x1
Aug 24 04:44:55 tempname kernel: Initializing CPU#2
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4267.09 BogoMIPS (lpj=8534184)
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 2/1 -> Node 0
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 1
Aug 24 04:44:55 tempname kernel: CPU2: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:44:55 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Aug 24 04:44:55 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:44:55 tempname kernel: Booting processor 3/4 APIC 0x3
Aug 24 04:44:55 tempname kernel: Initializing CPU#3
Aug 24 04:44:55 tempname kernel: Calibrating delay using timer specific routine.. 4267.14 BogoMIPS (lpj=8534284)
Aug 24 04:44:55 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:44:55 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:44:55 tempname kernel: CPU 3/3 -> Node 0
Aug 24 04:44:55 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:44:55 tempname kernel: CPU: Processor Core ID: 3
Aug 24 04:44:55 tempname kernel: CPU3: Thermal monitoring enabled (TM2)
Aug 24 04:44:55 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:44:55 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Aug 24 04:44:55 tempname kernel: Brought up 4 CPUs
Aug 24 04:44:55 tempname kernel: migration_cost=23,3090
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 16
Aug 24 04:44:55 tempname kernel: ACPI: bus type pci registered
Aug 24 04:44:55 tempname kernel: PCI: Using configuration type 1
Aug 24 04:44:55 tempname kernel: ACPI: Interpreter enabled
Aug 24 04:44:55 tempname kernel: ACPI: (supports S0 S1 S4 S5)
Aug 24 04:44:55 tempname kernel: ACPI: Using IOAPIC for interrupt routing
Aug 24 04:44:55 tempname kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
Aug 24 04:44:55 tempname kernel: PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
Aug 24 04:44:55 tempname kernel: PCI quirk: region 0500-053f claimed by ICH6 GPIO
Aug 24 04:44:55 tempname kernel: PCI: PXH quirk detected, disabling MSI for SHPC device
Aug 24 04:44:55 tempname kernel: PCI: Transparent bridge - 0000:00:1e.0
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:44:55 tempname kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Aug 24 04:44:55 tempname kernel: pnp: PnP ACPI init
Aug 24 04:44:55 tempname kernel: ACPI: bus type pnp registered
Aug 24 04:44:55 tempname kernel: pnp: PnP ACPI: found 11 devices
Aug 24 04:44:55 tempname kernel: ACPI: ACPI bus type pnp unregistered
Aug 24 04:44:55 tempname kernel: usbcore: registered new interface driver usbfs
Aug 24 04:44:55 tempname kernel: usbcore: registered new interface driver hub
Aug 24 04:44:55 tempname kernel: usbcore: registered new device driver usb
Aug 24 04:44:55 tempname kernel: PCI: Using ACPI for IRQ routing
Aug 24 04:44:55 tempname kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 8
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 20
Aug 24 04:44:55 tempname kernel: PCI-GART: No AMD northbridge found.
Aug 24 04:44:55 tempname kernel: ACPI: RTC can wake from S4
Aug 24 04:44:55 tempname kernel: pnp: 00:01: ioport range 0x779-0x780 has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:06: ioport range 0x500-0x53f has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:06: ioport range 0x400-0x47f has been reserved
Aug 24 04:44:55 tempname kernel: pnp: 00:06: ioport range 0x680-0x6ff has been reserved
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:01:00.0
Aug 24 04:44:55 tempname kernel: IO window: 3000-3fff
Aug 24 04:44:55 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:44:55 tempname kernel: Time: tsc clocksource has been installed.
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1c.0
Aug 24 04:44:55 tempname kernel: IO window: 3000-3fff
Aug 24 04:44:55 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1c.4
Aug 24 04:44:55 tempname kernel: IO window: disabled.
Aug 24 04:44:55 tempname kernel: MEM window: disabled.
Aug 24 04:44:55 tempname kernel: PREFETCH window: disabled.
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1c.5
Aug 24 04:44:55 tempname kernel: IO window: 2000-2fff
Aug 24 04:44:55 tempname kernel: MEM window: e8100000-e81fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: disabled.
Aug 24 04:44:55 tempname kernel: PCI: Bridge: 0000:00:1e.0
Aug 24 04:44:55 tempname kernel: IO window: 1000-1fff
Aug 24 04:44:55 tempname kernel: MEM window: e8000000-e80fffff
Aug 24 04:44:55 tempname kernel: PREFETCH window: e0000000-e7ffffff
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 2
Aug 24 04:44:55 tempname kernel: IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Aug 24 04:44:55 tempname kernel: TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
Aug 24 04:44:55 tempname kernel: TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Aug 24 04:44:55 tempname kernel: TCP: Hash tables configured (established 524288 bind 65536)
Aug 24 04:44:55 tempname kernel: TCP reno registered
Aug 24 04:44:55 tempname kernel: checking if image is initramfs... it is
Aug 24 04:44:55 tempname kernel: Freeing initrd memory: 5837k freed
Aug 24 04:44:55 tempname kernel: audit: initializing netlink socket (disabled)
Aug 24 04:44:55 tempname kernel: audit(1187923442.852:1): initialized
Aug 24 04:44:55 tempname kernel: VFS: Disk quotas dquot_6.5.1
Aug 24 04:44:55 tempname kernel: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Aug 24 04:44:55 tempname kernel: io scheduler noop registered
Aug 24 04:44:55 tempname kernel: io scheduler anticipatory registered
Aug 24 04:44:55 tempname kernel: io scheduler deadline registered
Aug 24 04:44:55 tempname kernel: io scheduler cfq registered (default)
Aug 24 04:44:55 tempname kernel: 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
Aug 24 04:44:55 tempname kernel: assign_interrupt_mode Found MSI capability
Aug 24 04:44:55 tempname last message repeated 2 times
Aug 24 04:44:55 tempname kernel: Real Time Clock Driver v1.12ac
Aug 24 04:44:55 tempname kernel: Linux agpgart interface v0.102 (c) Dave Jones
Aug 24 04:44:55 tempname kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Aug 24 04:44:55 tempname kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:04:00.3[C] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: 0000:04:00.3: ttyS1 at I/O 0x2020 (irq = 19) is a 16550A
Aug 24 04:44:55 tempname kernel: RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Aug 24 04:44:55 tempname kernel: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
Aug 24 04:44:55 tempname kernel: PNP: PS/2 controller doesn't have AUX irq; using default 12
Aug 24 04:44:55 tempname kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Aug 24 04:44:55 tempname kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Aug 24 04:44:55 tempname kernel: mice: PS/2 mouse device common for all mice
Aug 24 04:44:55 tempname kernel: TCP bic registered
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 1
Aug 24 04:44:55 tempname kernel: NET: Registered protocol family 17
Aug 24 04:44:55 tempname kernel: Freeing unused kernel memory: 296k freed
Aug 24 04:44:55 tempname kernel: input: AT Translated Set 2 keyboard as /class/input/input0
Aug 24 04:44:55 tempname kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Aug 24 04:44:55 tempname kernel: Copyright (c) 1999-2006 Intel Corporation.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: SCSI subsystem initialized
Aug 24 04:44:55 tempname kernel: USB Universal Host Controller Interface driver v3.0
Aug 24 04:44:55 tempname kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Aug 24 04:44:55 tempname kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 24 04:44:55 tempname kernel: FDC 0 is a post-1991 82077
Aug 24 04:44:55 tempname kernel: e1000: 0000:04:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:17:1b:d4:45
Aug 24 04:44:55 tempname kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:05:05.0[A] -> <6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
Aug 24 04:44:55 tempname kernel: usb usb1: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 1-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 1-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: GSI 17 (level, low) -> IRQ 17
Aug 24 04:44:55 tempname kernel: e1000: 0000:05:05.0: e1000_probe: (PCI:33MHz:32-bit) 00:15:17:1b:d4:46
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
Aug 24 04:44:55 tempname kernel: usb usb2: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 2-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 2-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
Aug 24 04:44:55 tempname kernel: usb usb3: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 3-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 3-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
Aug 24 04:44:55 tempname kernel: uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
Aug 24 04:44:55 tempname kernel: usb usb4: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 4-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 4-0:1.0: 2 ports detected
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: debug port 1
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe8300400
Aug 24 04:44:55 tempname kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Aug 24 04:44:55 tempname kernel: usb usb5: configuration #1 chosen from 1 choice
Aug 24 04:44:55 tempname kernel: hub 5-0:1.0: USB hub found
Aug 24 04:44:55 tempname kernel: hub 5-0:1.0: 8 ports detected
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
Aug 24 04:44:55 tempname kernel: ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
Aug 24 04:44:55 tempname kernel: scsi0 : ahci
Aug 24 04:44:55 tempname kernel: scsi1 : ahci
Aug 24 04:44:55 tempname kernel: scsi2 : ahci
Aug 24 04:44:55 tempname kernel: scsi3 : ahci
Aug 24 04:44:55 tempname kernel: ata1: SATA max UDMA/133 cmd 0xffffc20001434100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata2: SATA max UDMA/133 cmd 0xffffc20001434180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata3: SATA max UDMA/133 cmd 0xffffc20001434200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata4: SATA max UDMA/133 cmd 0xffffc20001434280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:44:55 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:44:55 tempname kernel: ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:44:55 tempname kernel: ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:44:55 tempname kernel: ata1.00: configured for UDMA/133
Aug 24 04:44:55 tempname kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:44:55 tempname kernel: ata2.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:44:55 tempname kernel: ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:44:55 tempname kernel: ata2.00: configured for UDMA/133
Aug 24 04:44:55 tempname kernel: ata3: SATA link down (SStatus 0 SControl 300)
Aug 24 04:44:55 tempname kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:44:55 tempname kernel: ata4.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:44:55 tempname kernel: ata4.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:44:55 tempname kernel: ata4.00: configured for UDMA/133
Aug 24 04:44:55 tempname kernel: scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:44:55 tempname kernel: scsi 1:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:44:55 tempname kernel: scsi 3:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 35 (level, low) -> IRQ 35
Aug 24 04:44:55 tempname kernel: ICH7: IDE controller at PCI slot 0000:00:1f.1
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:44:55 tempname kernel: ICH7: chipset revision 1
Aug 24 04:44:55 tempname kernel: ICH7: not 100%% native mode: will probe irqs later
Aug 24 04:44:55 tempname kernel: ide0: BM-DMA at 0x40b0-0x40b7, BIOS settings: hda:pio, hdb:pio
Aug 24 04:44:55 tempname kernel: ide1: BM-DMA at 0x40b8-0x40bf, BIOS settings: hdc:pio, hdd:pio
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sda: sda1
Aug 24 04:44:55 tempname kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sdb: sdb1
Aug 24 04:44:55 tempname kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:44:55 tempname kernel: sdc: sdc1
Aug 24 04:44:55 tempname kernel: sd 3:0:0:0: [sdc] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: scsi4 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:44:55 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:44:55 tempname kernel: aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Aug 24 04:44:55 tempname kernel:
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:02:02.1[B] -> GSI 36 (level, low) -> IRQ 36
Aug 24 04:44:55 tempname kernel: scsi 4:0:1:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi4:A:1:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target4:0:1: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target4:0:1: wide asynchronous
Aug 24 04:44:55 tempname kernel: target4:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target4:0:1: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: scsi 4:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi4:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target4:0:2: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target4:0:2: wide asynchronous
Aug 24 04:44:55 tempname kernel: target4:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target4:0:2: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sdd: sdd1
Aug 24 04:44:55 tempname kernel: sd 4:0:1:0: [sdd] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sde: unknown partition table
Aug 24 04:44:55 tempname kernel: sd 4:0:2:0: [sde] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: scsi5 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:44:55 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:44:55 tempname kernel: aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
Aug 24 04:44:55 tempname kernel:
Aug 24 04:44:55 tempname kernel: scsi 5:0:0:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi5:A:0:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target5:0:0: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target5:0:0: wide asynchronous
Aug 24 04:44:55 tempname kernel: target5:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target5:0:0: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: scsi 5:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:44:55 tempname kernel: scsi5:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:44:55 tempname kernel: target5:0:2: Beginning Domain Validation
Aug 24 04:44:55 tempname kernel: target5:0:2: wide asynchronous
Aug 24 04:44:55 tempname kernel: target5:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:44:55 tempname kernel: target5:0:2: Ending Domain Validation
Aug 24 04:44:55 tempname kernel: raid5: automatically using best checksumming function: generic_sse
Aug 24 04:44:55 tempname kernel: generic_sse: 7609.000 MB/sec
Aug 24 04:44:55 tempname kernel: raid5: using function: generic_sse (7609.000 MB/sec)
Aug 24 04:44:55 tempname kernel: raid6: int64x1 2001 MB/s
Aug 24 04:44:55 tempname kernel: raid6: int64x2 2696 MB/s
Aug 24 04:44:55 tempname kernel: raid6: int64x4 2366 MB/s
Aug 24 04:44:55 tempname kernel: raid6: int64x8 1531 MB/s
Aug 24 04:44:55 tempname kernel: raid6: sse2x1 3419 MB/s
Aug 24 04:44:55 tempname kernel: raid6: sse2x2 4151 MB/s
Aug 24 04:44:55 tempname kernel: raid6: sse2x4 6450 MB/s
Aug 24 04:44:55 tempname kernel: raid6: using algorithm sse2x4 (6450 MB/s)
Aug 24 04:44:55 tempname kernel: md: raid6 personality registered for level 6
Aug 24 04:44:55 tempname kernel: md: raid5 personality registered for level 5
Aug 24 04:44:55 tempname kernel: md: raid4 personality registered for level 4
Aug 24 04:44:55 tempname kernel: md: md2 stopped.
Aug 24 04:44:55 tempname kernel: md: bind<sdc1>
Aug 24 04:44:55 tempname kernel: md: bind<sdb1>
Aug 24 04:44:55 tempname kernel: raid5: device sdb1 operational as raid disk 0
Aug 24 04:44:55 tempname kernel: raid5: device sdc1 operational as raid disk 2
Aug 24 04:44:55 tempname kernel: raid5: allocated 3212kB for md2
Aug 24 04:44:55 tempname kernel: RAID5 conf printout:
Aug 24 04:44:55 tempname kernel: --- rd:3 wd:2
Aug 24 04:44:55 tempname kernel: disk 0, o:1, dev:sdb1
Aug 24 04:44:55 tempname kernel: disk 2, o:1, dev:sdc1
Aug 24 04:44:55 tempname kernel: kjournald starting. Commit interval 5 seconds
Aug 24 04:44:55 tempname kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 24 04:44:55 tempname kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Aug 24 04:44:55 tempname kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Aug 24 04:44:55 tempname kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
Aug 24 04:44:55 tempname kernel: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
Aug 24 04:44:55 tempname kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Aug 24 04:44:55 tempname kernel: input: PC Speaker as /class/input/input1
Aug 24 04:44:55 tempname kernel: intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
Aug 24 04:44:55 tempname kernel: don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
Aug 24 04:44:55 tempname kernel: you are certain that your <4>intel_rng: system has a functional
Aug 24 04:44:55 tempname kernel: RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
Aug 24 04:44:55 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sdf: unknown partition table
Aug 24 04:44:55 tempname kernel: sd 5:0:0:0: [sdf] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write Protect is off
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:44:55 tempname kernel: sdg: unknown partition table
Aug 24 04:44:55 tempname kernel: sd 5:0:2:0: [sdg] Attached SCSI disk
Aug 24 04:44:55 tempname kernel: EXT3 FS on sdd1, internal journal
Aug 24 04:44:55 tempname kernel: loop: module loaded
Aug 24 04:44:55 tempname kernel: coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:44:55 tempname kernel: device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Aug 24 04:44:55 tempname kernel: md: bind<sda1>
Aug 24 04:44:55 tempname kernel: Ebtables v2.0 registered
Aug 24 04:44:55 tempname kernel: Bridge firewalling registered
Aug 24 04:44:56 tempname kernel: NET: Registered protocol family 10
Aug 24 04:44:56 tempname kernel: lo: Disabled Privacy Extensions
Aug 24 04:44:56 tempname hpiod: 1.6.10 accepting connections at 2208...
Aug 24 04:44:57 tempname kernel: input: Power Button (FF) as /class/input/input2
Aug 24 04:44:57 tempname kernel: ACPI: Power Button (FF) [PWRF]
Aug 24 04:44:57 tempname kernel: input: Sleep Button (CM) as /class/input/input3
Aug 24 04:44:57 tempname kernel: ACPI: Sleep Button (CM) [SLPB]
Aug 24 04:44:57 tempname kernel: lp: driver loaded but no devices found
Aug 24 04:44:57 tempname kernel: ppdev: user-space parallel port driver
Aug 24 04:44:59 tempname dhcdbd: Started up.
Aug 24 04:44:59 tempname kernel: mdadm[4321]: segfault at 0000000000000000 rip 000000000041248e rsp 00007fff10299580 error 4
Aug 24 04:48:29 tempname shutdown[4548]: shutting down for system halt
Aug 24 04:48:37 tempname kernel: Ebtables v2.0 unregistered
Aug 24 04:48:37 tempname kernel: Kernel logging (proc) stopped.
Aug 24 04:48:37 tempname kernel: Kernel log daemon terminating.
Aug 24 04:48:38 tempname exiting on signal 15
Aug 24 04:55:11 tempname syslogd 1.4.1#20: restart.
Aug 24 04:55:11 tempname kernel: klogd 1.4.1#20, log source = /proc/kmsg started.
Aug 24 04:55:11 tempname kernel: Linux version 2.6.22-1-amd64 (Debian 2.6.22-2) (waldi@debian.org) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14)) #1 SMP Mon Jul 23 12:43:14 UTC 2007
Aug 24 04:55:11 tempname kernel: Command line: root=LABEL=soloscsi ro
Aug 24 04:55:11 tempname kernel: BIOS-provided physical RAM map:
Aug 24 04:55:11 tempname kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 000000000009d400 - 0000000000100000 (reserved)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 0000000000100000 - 00000000dfc0e000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfc0e000 - 00000000dfc5f000 (reserved)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfc5f000 - 00000000dfce6000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfce6000 - 00000000dfedf000 (ACPI NVS)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfedf000 - 00000000dfeed000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfeed000 - 00000000dfeff000 (ACPI data)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000dfeff000 - 00000000dff00000 (usable)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 00000000fffc0000 - 00000000fffd0000 (reserved)
Aug 24 04:55:11 tempname kernel: BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Aug 24 04:55:11 tempname kernel: end_pfn_map = 1179648
Aug 24 04:55:11 tempname kernel: DMI 2.4 present.
Aug 24 04:55:11 tempname kernel: ACPI: RSDP 000F0350, 0024 (r2 INTEL )
Aug 24 04:55:11 tempname kernel: ACPI: XSDT DFEFE120, 0074 (r1 INTEL S3000AHX 0 INTL 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: FACP DFEFB000, 00F4 (r3 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: DSDT DFEF6000, 4922 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: FACS DFE71000, 0040
Aug 24 04:55:11 tempname kernel: ACPI: APIC DFEF5000, 0084 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: WDDT DFEF4000, 0040 (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: MCFG DFEF3000, 003C (r1 INTEL S3000AHX 0 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: ASF! DFEF2000, 009F (r32 INTEL S3000AHX 1 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEF1000, 0175 (r1 INTEL Cpu0Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEF0000, 0175 (r1 INTEL Cpu1Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEEF000, 0175 (r1 INTEL Cpu2Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEEE000, 0175 (r1 INTEL Cpu3Ist 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: ACPI: SSDT DFEED000, 01BC (r1 INTEL CpuPm 10 MSFT 1000013)
Aug 24 04:55:11 tempname kernel: No NUMA configuration found
Aug 24 04:55:11 tempname kernel: Faking a node at 0000000000000000-0000000120000000
Aug 24 04:55:11 tempname kernel: Bootmem setup node 0 0000000000000000-0000000120000000
Aug 24 04:55:11 tempname kernel: Zone PFN ranges:
Aug 24 04:55:11 tempname kernel: DMA 0 -> 4096
Aug 24 04:55:11 tempname kernel: DMA32 4096 -> 1048576
Aug 24 04:55:11 tempname kernel: Normal 1048576 -> 1179648
Aug 24 04:55:11 tempname kernel: early_node_map[6] active PFN ranges
Aug 24 04:55:11 tempname kernel: 0: 0 -> 157
Aug 24 04:55:11 tempname kernel: 0: 256 -> 916494
Aug 24 04:55:11 tempname kernel: 0: 916575 -> 916710
Aug 24 04:55:11 tempname kernel: 0: 917215 -> 917229
Aug 24 04:55:11 tempname kernel: 0: 917247 -> 917248
Aug 24 04:55:11 tempname kernel: 0: 1048576 -> 1179648
Aug 24 04:55:11 tempname kernel: ACPI: PM-Timer IO Port: 0x408
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Aug 24 04:55:11 tempname kernel: Processor #0 (Bootup-CPU)
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Aug 24 04:55:11 tempname kernel: Processor #2
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Aug 24 04:55:11 tempname kernel: Processor #1
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Aug 24 04:55:11 tempname kernel: Processor #3
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
Aug 24 04:55:11 tempname kernel: ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Aug 24 04:55:11 tempname kernel: ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
Aug 24 04:55:11 tempname kernel: IOAPIC[0]: apic_id 5, address 0xfec00000, GSI 0-23
Aug 24 04:55:11 tempname kernel: ACPI: IOAPIC (id[0x06] address[0xfec10000] gsi_base[30])
Aug 24 04:55:11 tempname kernel: IOAPIC[1]: apic_id 6, address 0xfec10000, GSI 30-53
Aug 24 04:55:11 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Aug 24 04:55:11 tempname kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Aug 24 04:55:11 tempname kernel: Setting APIC routing to flat
Aug 24 04:55:11 tempname kernel: Using ACPI (MADT) for SMP configuration information
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 000000000009e000 - 0000000000100000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dfc0e000 - 00000000dfc5f000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dfce6000 - 00000000dfedf000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dfeed000 - 00000000dfeff000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000dff00000 - 00000000fffc0000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000fffc0000 - 00000000fffd0000
Aug 24 04:55:11 tempname kernel: swsusp: Registered nosave memory region: 00000000fffd0000 - 0000000100000000
Aug 24 04:55:11 tempname kernel: Allocating PCI resources starting at e0000000 (gap: dff00000:200c0000)
Aug 24 04:55:11 tempname kernel: SMP: Allowing 4 CPUs, 0 hotplug CPUs
Aug 24 04:55:11 tempname kernel: PERCPU: Allocating 37896 bytes of per cpu data
Aug 24 04:55:11 tempname kernel: Built 1 zonelists. Total pages: 1030465
Aug 24 04:55:11 tempname kernel: Kernel command line: root=LABEL=soloscsi ro
Aug 24 04:55:11 tempname kernel: Initializing CPU#0
Aug 24 04:55:11 tempname kernel: PID hash table entries: 4096 (order: 12, 32768 bytes)
Aug 24 04:55:11 tempname kernel: time.c: Detected 2133.450 MHz processor.
Aug 24 04:55:11 tempname kernel: Console: colour VGA+ 80x25
Aug 24 04:55:11 tempname kernel: Checking aperture...
Aug 24 04:55:11 tempname kernel: PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Aug 24 04:55:11 tempname kernel: Placing software IO TLB between 0x1050000 - 0x5050000
Aug 24 04:55:11 tempname kernel: Memory: 4049736k/4718592k available (2009k kernel code, 140732k reserved, 946k data, 296k init)
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4270.10 BogoMIPS (lpj=8540211)
Aug 24 04:55:11 tempname kernel: Security Framework v1.0.0 initialized
Aug 24 04:55:11 tempname kernel: SELinux: Disabled at boot.
Aug 24 04:55:11 tempname kernel: Capability LSM initialized
Aug 24 04:55:11 tempname kernel: Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Aug 24 04:55:11 tempname kernel: Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Aug 24 04:55:11 tempname kernel: Mount-cache hash table entries: 256
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 0/0 -> Node 0
Aug 24 04:55:11 tempname kernel: using mwait in idle threads.
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 0
Aug 24 04:55:11 tempname kernel: CPU0: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to UP code
Aug 24 04:55:11 tempname kernel: ACPI: Core revision 20070126
Aug 24 04:55:11 tempname kernel: Using local APIC timer interrupts.
Aug 24 04:55:11 tempname kernel: result 16667575
Aug 24 04:55:11 tempname kernel: Detected 16.667 MHz APIC timer.
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:55:11 tempname kernel: Booting processor 1/4 APIC 0x2
Aug 24 04:55:11 tempname kernel: Initializing CPU#1
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4267.17 BogoMIPS (lpj=8534344)
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 1/2 -> Node 0
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 2
Aug 24 04:55:11 tempname kernel: CPU1: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:55:11 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:55:11 tempname kernel: Booting processor 2/4 APIC 0x1
Aug 24 04:55:11 tempname kernel: Initializing CPU#2
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4267.18 BogoMIPS (lpj=8534372)
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 2/1 -> Node 0
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 1
Aug 24 04:55:11 tempname kernel: CPU2: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:55:11 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Aug 24 04:55:11 tempname kernel: SMP alternatives: switching to SMP code
Aug 24 04:55:11 tempname kernel: Booting processor 3/4 APIC 0x3
Aug 24 04:55:11 tempname kernel: Initializing CPU#3
Aug 24 04:55:11 tempname kernel: Calibrating delay using timer specific routine.. 4267.15 BogoMIPS (lpj=8534305)
Aug 24 04:55:11 tempname kernel: CPU: L1 I cache: 32K, L1 D cache: 32K
Aug 24 04:55:11 tempname kernel: CPU: L2 cache: 4096K
Aug 24 04:55:11 tempname kernel: CPU 3/3 -> Node 0
Aug 24 04:55:11 tempname kernel: CPU: Physical Processor ID: 0
Aug 24 04:55:11 tempname kernel: CPU: Processor Core ID: 3
Aug 24 04:55:11 tempname kernel: CPU3: Thermal monitoring enabled (TM2)
Aug 24 04:55:11 tempname kernel: Intel(R) Xeon(R) CPU X3210 @ 2.13GHz stepping 07
Aug 24 04:55:11 tempname kernel: checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Aug 24 04:55:11 tempname kernel: Brought up 4 CPUs
Aug 24 04:55:11 tempname kernel: migration_cost=17,3093
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 16
Aug 24 04:55:11 tempname kernel: ACPI: bus type pci registered
Aug 24 04:55:11 tempname kernel: PCI: Using configuration type 1
Aug 24 04:55:11 tempname kernel: ACPI: Interpreter enabled
Aug 24 04:55:11 tempname kernel: ACPI: (supports S0 S1 S4 S5)
Aug 24 04:55:11 tempname kernel: ACPI: Using IOAPIC for interrupt routing
Aug 24 04:55:11 tempname kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
Aug 24 04:55:11 tempname kernel: PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
Aug 24 04:55:11 tempname kernel: PCI quirk: region 0500-053f claimed by ICH6 GPIO
Aug 24 04:55:11 tempname kernel: PCI: PXH quirk detected, disabling MSI for SHPC device
Aug 24 04:55:11 tempname kernel: PCI: Transparent bridge - 0000:00:1e.0
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
Aug 24 04:55:11 tempname kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Aug 24 04:55:11 tempname kernel: pnp: PnP ACPI init
Aug 24 04:55:11 tempname kernel: ACPI: bus type pnp registered
Aug 24 04:55:11 tempname kernel: pnp: PnP ACPI: found 11 devices
Aug 24 04:55:11 tempname kernel: ACPI: ACPI bus type pnp unregistered
Aug 24 04:55:11 tempname kernel: usbcore: registered new interface driver usbfs
Aug 24 04:55:11 tempname kernel: usbcore: registered new interface driver hub
Aug 24 04:55:11 tempname kernel: usbcore: registered new device driver usb
Aug 24 04:55:11 tempname kernel: PCI: Using ACPI for IRQ routing
Aug 24 04:55:11 tempname kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 8
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 20
Aug 24 04:55:11 tempname kernel: PCI-GART: No AMD northbridge found.
Aug 24 04:55:11 tempname kernel: ACPI: RTC can wake from S4
Aug 24 04:55:11 tempname kernel: pnp: 00:01: ioport range 0x779-0x780 has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:06: ioport range 0x500-0x53f has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:06: ioport range 0x400-0x47f has been reserved
Aug 24 04:55:11 tempname kernel: pnp: 00:06: ioport range 0x680-0x6ff has been reserved
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:01:00.0
Aug 24 04:55:11 tempname kernel: IO window: 3000-3fff
Aug 24 04:55:11 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:55:11 tempname kernel: Time: tsc clocksource has been installed.
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1c.0
Aug 24 04:55:11 tempname kernel: IO window: 3000-3fff
Aug 24 04:55:11 tempname kernel: MEM window: e8200000-e82fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: e8400000-e84fffff
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1c.4
Aug 24 04:55:11 tempname kernel: IO window: disabled.
Aug 24 04:55:11 tempname kernel: MEM window: disabled.
Aug 24 04:55:11 tempname kernel: PREFETCH window: disabled.
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1c.5
Aug 24 04:55:11 tempname kernel: IO window: 2000-2fff
Aug 24 04:55:11 tempname kernel: MEM window: e8100000-e81fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: disabled.
Aug 24 04:55:11 tempname kernel: PCI: Bridge: 0000:00:1e.0
Aug 24 04:55:11 tempname kernel: IO window: 1000-1fff
Aug 24 04:55:11 tempname kernel: MEM window: e8000000-e80fffff
Aug 24 04:55:11 tempname kernel: PREFETCH window: e0000000-e7ffffff
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 2
Aug 24 04:55:11 tempname kernel: IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Aug 24 04:55:11 tempname kernel: TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
Aug 24 04:55:11 tempname kernel: TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Aug 24 04:55:11 tempname kernel: TCP: Hash tables configured (established 524288 bind 65536)
Aug 24 04:55:11 tempname kernel: TCP reno registered
Aug 24 04:55:11 tempname kernel: checking if image is initramfs... it is
Aug 24 04:55:11 tempname kernel: Freeing initrd memory: 5837k freed
Aug 24 04:55:11 tempname kernel: audit: initializing netlink socket (disabled)
Aug 24 04:55:11 tempname kernel: audit(1187924057.764:1): initialized
Aug 24 04:55:11 tempname kernel: VFS: Disk quotas dquot_6.5.1
Aug 24 04:55:11 tempname kernel: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Aug 24 04:55:11 tempname kernel: io scheduler noop registered
Aug 24 04:55:11 tempname kernel: io scheduler anticipatory registered
Aug 24 04:55:11 tempname kernel: io scheduler deadline registered
Aug 24 04:55:11 tempname kernel: io scheduler cfq registered (default)
Aug 24 04:55:11 tempname kernel: 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
Aug 24 04:55:11 tempname kernel: assign_interrupt_mode Found MSI capability
Aug 24 04:55:11 tempname last message repeated 2 times
Aug 24 04:55:11 tempname kernel: Real Time Clock Driver v1.12ac
Aug 24 04:55:11 tempname kernel: Linux agpgart interface v0.102 (c) Dave Jones
Aug 24 04:55:11 tempname kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Aug 24 04:55:11 tempname kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:04:00.3[C] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: 0000:04:00.3: ttyS1 at I/O 0x2020 (irq = 19) is a 16550A
Aug 24 04:55:11 tempname kernel: RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Aug 24 04:55:11 tempname kernel: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
Aug 24 04:55:11 tempname kernel: PNP: PS/2 controller doesn't have AUX irq; using default 12
Aug 24 04:55:11 tempname kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Aug 24 04:55:11 tempname kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Aug 24 04:55:11 tempname kernel: mice: PS/2 mouse device common for all mice
Aug 24 04:55:11 tempname kernel: TCP bic registered
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 1
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 17
Aug 24 04:55:11 tempname kernel: Freeing unused kernel memory: 296k freed
Aug 24 04:55:11 tempname kernel: input: AT Translated Set 2 keyboard as /class/input/input0
Aug 24 04:55:11 tempname kernel: USB Universal Host Controller Interface driver v3.0
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
Aug 24 04:55:11 tempname kernel: usb usb1: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 1-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 1-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Aug 24 04:55:11 tempname kernel: Copyright (c) 1999-2006 Intel Corporation.
Aug 24 04:55:11 tempname kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Aug 24 04:55:11 tempname kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 24 04:55:11 tempname kernel: SCSI subsystem initialized
Aug 24 04:55:11 tempname kernel: FDC 0 is a post-1991 82077
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
Aug 24 04:55:11 tempname kernel: usb usb2: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 2-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 2-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
Aug 24 04:55:11 tempname kernel: usb usb3: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 3-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 3-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
Aug 24 04:55:11 tempname kernel: uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
Aug 24 04:55:11 tempname kernel: usb usb4: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 4-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 4-0:1.0: 2 ports detected
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
Aug 24 04:55:11 tempname kernel: ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
Aug 24 04:55:11 tempname kernel: scsi0 : ahci
Aug 24 04:55:11 tempname kernel: scsi1 : ahci
Aug 24 04:55:11 tempname kernel: scsi2 : ahci
Aug 24 04:55:11 tempname kernel: scsi3 : ahci
Aug 24 04:55:11 tempname kernel: ata1: SATA max UDMA/133 cmd 0xffffc20001432100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata2: SATA max UDMA/133 cmd 0xffffc20001432180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata3: SATA max UDMA/133 cmd 0xffffc20001432200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata4: SATA max UDMA/133 cmd 0xffffc20001432280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
Aug 24 04:55:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata1.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata2.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata2.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata3.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata3.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata3.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:55:11 tempname kernel: ata4.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
Aug 24 04:55:11 tempname kernel: ata4.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
Aug 24 04:55:11 tempname kernel: ata4.00: configured for UDMA/133
Aug 24 04:55:11 tempname kernel: scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: scsi 1:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: scsi 2:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: scsi 3:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: debug port 1
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe8300400
Aug 24 04:55:11 tempname kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Aug 24 04:55:11 tempname kernel: usb usb5: configuration #1 chosen from 1 choice
Aug 24 04:55:11 tempname kernel: hub 5-0:1.0: USB hub found
Aug 24 04:55:11 tempname kernel: hub 5-0:1.0: 8 ports detected
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sda: sda1
Aug 24 04:55:11 tempname kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sdb: sdb1
Aug 24 04:55:11 tempname kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sdc:<6>e1000: 0000:04:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:15:17:1b:d4:45
Aug 24 04:55:11 tempname kernel: sdc1
Aug 24 04:55:11 tempname kernel: sd 2:0:0:0: [sdc] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:11 tempname kernel: sdd: sdd1
Aug 24 04:55:11 tempname kernel: sd 3:0:0:0: [sdd] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 17 (level, low) -> IRQ 17
Aug 24 04:55:11 tempname kernel: e1000: 0000:05:05.0: e1000_probe: (PCI:33MHz:32-bit) 00:15:17:1b:d4:46
Aug 24 04:55:11 tempname kernel: e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 35 (level, low) -> IRQ 35
Aug 24 04:55:11 tempname kernel: scsi4 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:55:11 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:55:11 tempname kernel: aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Aug 24 04:55:11 tempname kernel:
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:02:02.1[B] -> GSI 36 (level, low) -> IRQ 36
Aug 24 04:55:11 tempname kernel: scsi 4:0:1:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi4:A:1:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target4:0:1: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target4:0:1: wide asynchronous
Aug 24 04:55:11 tempname kernel: target4:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target4:0:1: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: scsi 4:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi4:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target4:0:2: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target4:0:2: wide asynchronous
Aug 24 04:55:11 tempname kernel: target4:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target4:0:2: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sde: sde1
Aug 24 04:55:11 tempname kernel: sd 4:0:1:0: [sde] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sdf: unknown partition table
Aug 24 04:55:11 tempname kernel: sd 4:0:2:0: [sdf] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: scsi5 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
Aug 24 04:55:11 tempname kernel: <Adaptec 3960D Ultra160 SCSI adapter>
Aug 24 04:55:11 tempname kernel: aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
Aug 24 04:55:11 tempname kernel:
Aug 24 04:55:11 tempname kernel: ICH7: IDE controller at PCI slot 0000:00:1f.1
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
Aug 24 04:55:11 tempname kernel: ICH7: chipset revision 1
Aug 24 04:55:11 tempname kernel: ICH7: not 100%% native mode: will probe irqs later
Aug 24 04:55:11 tempname kernel: ide0: BM-DMA at 0x40b0-0x40b7, BIOS settings: hda:pio, hdb:pio
Aug 24 04:55:11 tempname kernel: ide1: BM-DMA at 0x40b8-0x40bf, BIOS settings: hdc:pio, hdd:pio
Aug 24 04:55:11 tempname kernel: scsi 5:0:0:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi5:A:0:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target5:0:0: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target5:0:0: wide asynchronous
Aug 24 04:55:11 tempname kernel: target5:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target5:0:0: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: scsi 5:0:2:0: Direct-Access SEAGATE ST336754LW D402 PQ: 0 ANSI: 3
Aug 24 04:55:11 tempname kernel: scsi5:A:2:0: Tagged Queuing enabled. Depth 8
Aug 24 04:55:11 tempname kernel: target5:0:2: Beginning Domain Validation
Aug 24 04:55:11 tempname kernel: target5:0:2: wide asynchronous
Aug 24 04:55:11 tempname kernel: target5:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
Aug 24 04:55:11 tempname kernel: target5:0:2: Ending Domain Validation
Aug 24 04:55:11 tempname kernel: raid5: automatically using best checksumming function: generic_sse
Aug 24 04:55:11 tempname kernel: generic_sse: 7611.000 MB/sec
Aug 24 04:55:11 tempname kernel: raid5: using function: generic_sse (7611.000 MB/sec)
Aug 24 04:55:11 tempname kernel: raid6: int64x1 2000 MB/s
Aug 24 04:55:11 tempname kernel: raid6: int64x2 2677 MB/s
Aug 24 04:55:11 tempname kernel: raid6: int64x4 2373 MB/s
Aug 24 04:55:11 tempname kernel: raid6: int64x8 1534 MB/s
Aug 24 04:55:11 tempname kernel: raid6: sse2x1 3419 MB/s
Aug 24 04:55:11 tempname kernel: raid6: sse2x2 4532 MB/s
Aug 24 04:55:11 tempname kernel: raid6: sse2x4 6506 MB/s
Aug 24 04:55:11 tempname kernel: raid6: using algorithm sse2x4 (6506 MB/s)
Aug 24 04:55:11 tempname kernel: md: raid6 personality registered for level 6
Aug 24 04:55:11 tempname kernel: md: raid5 personality registered for level 5
Aug 24 04:55:11 tempname kernel: md: raid4 personality registered for level 4
Aug 24 04:55:11 tempname kernel: md: md2 stopped.
Aug 24 04:55:11 tempname kernel: md: bind<sdc1>
Aug 24 04:55:11 tempname kernel: md: bind<sdd1>
Aug 24 04:55:11 tempname kernel: md: bind<sdb1>
Aug 24 04:55:11 tempname kernel: raid5: device sdb1 operational as raid disk 0
Aug 24 04:55:11 tempname kernel: raid5: device sdd1 operational as raid disk 2
Aug 24 04:55:11 tempname kernel: raid5: device sdc1 operational as raid disk 1
Aug 24 04:55:11 tempname kernel: raid5: allocated 3212kB for md2
Aug 24 04:55:11 tempname kernel: raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
Aug 24 04:55:11 tempname kernel: RAID5 conf printout:
Aug 24 04:55:11 tempname kernel: --- rd:3 wd:3
Aug 24 04:55:11 tempname kernel: disk 0, o:1, dev:sdb1
Aug 24 04:55:11 tempname kernel: disk 1, o:1, dev:sdc1
Aug 24 04:55:11 tempname kernel: disk 2, o:1, dev:sdd1
Aug 24 04:55:11 tempname kernel: kjournald starting. Commit interval 5 seconds
Aug 24 04:55:11 tempname kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sdg: unknown partition table
Aug 24 04:55:11 tempname kernel: sd 5:0:0:0: [sdg] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] 71132959 512-byte hardware sectors (36420 MB)
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write Protect is off
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
Aug 24 04:55:11 tempname kernel: sdh: unknown partition table
Aug 24 04:55:11 tempname kernel: sd 5:0:2:0: [sdh] Attached SCSI disk
Aug 24 04:55:11 tempname kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Aug 24 04:55:11 tempname kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Aug 24 04:55:11 tempname kernel: input: PC Speaker as /class/input/input1
Aug 24 04:55:11 tempname kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
Aug 24 04:55:11 tempname kernel: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
Aug 24 04:55:11 tempname kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Aug 24 04:55:11 tempname kernel: ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
Aug 24 04:55:11 tempname kernel: intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
Aug 24 04:55:11 tempname kernel: don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
Aug 24 04:55:11 tempname kernel: you are certain that your <4>intel_rng: system has a functional
Aug 24 04:55:11 tempname kernel: RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
Aug 24 04:55:11 tempname kernel: EXT3 FS on sde1, internal journal
Aug 24 04:55:11 tempname kernel: loop: module loaded
Aug 24 04:55:11 tempname kernel: coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
Aug 24 04:55:11 tempname kernel: device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Aug 24 04:55:11 tempname kernel: md: bind<sda1>
Aug 24 04:55:11 tempname kernel: Ebtables v2.0 registered
Aug 24 04:55:11 tempname kernel: Bridge firewalling registered
Aug 24 04:55:11 tempname kernel: e1000: eth3: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Aug 24 04:55:11 tempname kernel: NET: Registered protocol family 10
Aug 24 04:55:11 tempname kernel: lo: Disabled Privacy Extensions
Aug 24 04:55:12 tempname hpiod: 1.6.10 accepting connections at 2208...
Aug 24 04:55:13 tempname kernel: input: Power Button (FF) as /class/input/input2
Aug 24 04:55:13 tempname kernel: ACPI: Power Button (FF) [PWRF]
Aug 24 04:55:13 tempname kernel: input: Sleep Button (CM) as /class/input/input3
Aug 24 04:55:13 tempname kernel: ACPI: Sleep Button (CM) [SLPB]
Aug 24 04:55:13 tempname kernel: lp: driver loaded but no devices found
Aug 24 04:55:13 tempname kernel: ppdev: user-space parallel port driver
Aug 24 04:55:14 tempname dhcdbd: Started up.
Aug 24 04:55:15 tempname kernel: mdadm[4375]: segfault at 0000000000000000 rip 000000000041248e rsp 00007fffa2b38e20 error 4
Aug 23 20:57:38 tempname kernel: md: md2 stopped.
Aug 23 20:57:38 tempname kernel: md: unbind<sdb1>
Aug 23 20:57:38 tempname kernel: md: export_rdev(sdb1)
Aug 23 20:57:38 tempname kernel: md: unbind<sdd1>
Aug 23 20:57:38 tempname kernel: md: export_rdev(sdd1)
Aug 23 20:57:38 tempname kernel: md: unbind<sdc1>
Aug 23 20:57:38 tempname kernel: md: export_rdev(sdc1)
Aug 23 20:59:23 tempname kernel: md: md1 stopped.
Aug 23 20:59:23 tempname kernel: md: unbind<sda1>
Aug 23 20:59:23 tempname kernel: md: export_rdev(sda1)
Aug 23 20:59:23 tempname kernel: md: bind<sdc1>
Aug 23 20:59:23 tempname kernel: md: bind<sdd1>
Aug 23 20:59:23 tempname kernel: md: bind<sdb1>
Aug 23 20:59:23 tempname kernel: raid5: device sdb1 operational as raid disk 0
Aug 23 20:59:23 tempname kernel: raid5: device sdd1 operational as raid disk 2
Aug 23 20:59:23 tempname kernel: raid5: device sdc1 operational as raid disk 1
Aug 23 20:59:23 tempname kernel: raid5: allocated 3212kB for md2
Aug 23 20:59:23 tempname kernel: raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
Aug 23 20:59:23 tempname kernel: RAID5 conf printout:
Aug 23 20:59:23 tempname kernel: --- rd:3 wd:3
Aug 23 20:59:23 tempname kernel: disk 0, o:1, dev:sdb1
Aug 23 20:59:23 tempname kernel: disk 1, o:1, dev:sdc1
Aug 23 20:59:23 tempname kernel: disk 2, o:1, dev:sdd1
Aug 23 20:59:23 tempname kernel: mdadm[4567]: segfault at 0000000000000000 rip 000000000041248e rsp 00007fff39111510 error 4
Aug 23 20:59:23 tempname kernel: md: bind<sda1>
Aug 23 20:59:47 tempname kernel: md: md2 stopped.
Aug 23 20:59:47 tempname kernel: md: unbind<sdb1>
Aug 23 20:59:47 tempname kernel: md: export_rdev(sdb1)
Aug 23 20:59:47 tempname kernel: md: unbind<sdd1>
Aug 23 20:59:47 tempname kernel: md: export_rdev(sdd1)
Aug 23 20:59:47 tempname kernel: md: unbind<sdc1>
Aug 23 20:59:47 tempname kernel: md: export_rdev(sdc1)
Aug 23 21:00:24 tempname kernel: res 40/00:10:30:08:05/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:24 tempname last message repeated 16 times
Aug 23 21:00:24 tempname kernel: ata1: soft resetting port
Aug 23 21:00:28 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:28 tempname kernel: ata1.00: configured for UDMA/133
Aug 23 21:00:28 tempname kernel: ata1: EH complete
Aug 23 21:00:28 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:28 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:28 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:00:44 tempname kernel: res 40/00:20:60:e7:0a/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:44 tempname last message repeated 4 times
Aug 23 21:00:45 tempname kernel: ata1: soft resetting port
Aug 23 21:00:48 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:49 tempname kernel: ata1.00: configured for UDMA/133
Aug 23 21:00:49 tempname kernel: ata1: EH complete
Aug 23 21:00:49 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:49 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:49 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:00:50 tempname kernel: res 40/00:08:18:29:0b/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:50 tempname last message repeated 12 times
Aug 23 21:00:50 tempname kernel: ata1: soft resetting port
Aug 23 21:00:54 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:54 tempname kernel: ata1.00: configured for UDMA/133
Aug 23 21:00:54 tempname kernel: ata1: EH complete
Aug 23 21:00:54 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:54 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:54 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:00:55 tempname kernel: ata1.00: limiting speed to UDMA/100:PIO4
Aug 23 21:00:55 tempname kernel: res 40/00:08:a8:b6:0b/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:00:55 tempname last message repeated 3 times
Aug 23 21:00:56 tempname kernel: ata1: soft resetting port
Aug 23 21:00:59 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:00:59 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:00:59 tempname kernel: ata1: EH complete
Aug 23 21:00:59 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:00:59 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:00:59 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:01:01 tempname kernel: res 40/00:08:08:02:0c/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
Aug 23 21:01:01 tempname last message repeated 10 times
Aug 23 21:01:01 tempname kernel: ata1: soft resetting port
Aug 23 21:01:05 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:01:05 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:01:05 tempname kernel: ata1: EH complete
Aug 23 21:01:05 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:01:05 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:01:05 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:02:07 tempname syslogd 1.4.1#20: restart.
Aug 23 21:07:18 tempname kernel: ata1: hard resetting port
Aug 23 21:07:24 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 23 21:07:28 tempname kernel: ata1: hard resetting port
Aug 23 21:07:29 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:07:29 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:07:29 tempname kernel: ata1: EH complete
Aug 23 21:07:29 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:07:29 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:07:29 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:13:41 tempname kernel: ata1: soft resetting port
Aug 23 21:13:44 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:13:44 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:13:44 tempname kernel: ata1: EH complete
Aug 23 21:13:44 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:13:44 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:13:44 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:19:56 tempname kernel: ata1: soft resetting port
Aug 23 21:19:59 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:19:59 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:19:59 tempname kernel: ata1: EH complete
Aug 23 21:19:59 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:19:59 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:19:59 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:26:11 tempname kernel: ata1: soft resetting port
Aug 23 21:26:15 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:26:15 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:26:15 tempname kernel: ata1: EH complete
Aug 23 21:26:15 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:26:15 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:26:15 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:32:27 tempname kernel: ata1: soft resetting port
Aug 23 21:32:31 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:32:31 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:32:31 tempname kernel: ata1: EH complete
Aug 23 21:32:31 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:32:31 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:32:31 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:38:42 tempname kernel: ata1: soft resetting port
Aug 23 21:38:46 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:38:46 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:38:46 tempname kernel: ata1: EH complete
Aug 23 21:38:46 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:38:46 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:38:46 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:39:49 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:39:49 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 23 21:39:49 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:39:49 tempname kernel: sdb: sdb1
Aug 23 21:40:31 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:40:31 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 23 21:40:31 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:40:31 tempname kernel: sdc: sdc1
Aug 23 21:44:57 tempname kernel: ata1: soft resetting port
Aug 23 21:45:01 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:45:01 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:45:01 tempname kernel: ata1: EH complete
Aug 23 21:45:01 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:45:01 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:45:01 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:47:03 tempname kernel: sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:47:03 tempname kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 23 21:47:03 tempname kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:47:04 tempname kernel: sdc: sdc1
Aug 23 21:48:13 tempname kernel: sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:48:13 tempname kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 23 21:48:13 tempname kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 21:48:13 tempname kernel: sdd: sdd1
Aug 23 21:54:40 tempname kernel: ata1: soft resetting port
Aug 23 21:54:44 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 21:54:44 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 21:54:44 tempname kernel: ata1: EH complete
Aug 23 21:54:44 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 21:54:44 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 21:54:44 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:00:57 tempname kernel: ata1: hard resetting port
Aug 23 22:01:02 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 23 22:01:07 tempname kernel: ata1: hard resetting port
Aug 23 22:01:07 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:01:08 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:01:08 tempname kernel: ata1: EH complete
Aug 23 22:01:08 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:01:08 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:01:08 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:07:18 tempname kernel: ata1: soft resetting port
Aug 23 22:07:22 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:07:22 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:07:22 tempname kernel: ata1: EH complete
Aug 23 22:07:22 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:07:22 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:07:22 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:08:01 tempname kernel: sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:08:01 tempname kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 23 22:08:01 tempname kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:08:01 tempname kernel: sdb: sdb1
Aug 23 22:13:35 tempname kernel: ata1: soft resetting port
Aug 23 22:13:39 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:13:39 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:13:39 tempname kernel: ata1: EH complete
Aug 23 22:13:39 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:13:39 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:13:39 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:15:31 tempname kernel: md: bind<sdb1>
Aug 23 22:15:33 tempname kernel: md: bind<sdc1>
Aug 23 22:15:34 tempname kernel: md: bind<sdd1>
Aug 23 22:15:35 tempname kernel: raid5: device sdd1 operational as raid disk 3
Aug 23 22:15:35 tempname kernel: raid5: device sdc1 operational as raid disk 2
Aug 23 22:15:35 tempname kernel: raid5: device sdb1 operational as raid disk 1
Aug 23 22:15:35 tempname kernel: RAID5 conf printout:
Aug 23 22:15:35 tempname kernel: --- rd:4 wd:3
Aug 23 22:15:35 tempname kernel: disk 1, o:1, dev:sdb1
Aug 23 22:15:35 tempname kernel: disk 2, o:1, dev:sdc1
Aug 23 22:15:35 tempname kernel: disk 3, o:1, dev:sdd1
Aug 23 22:15:35 tempname kernel: md: md2 stopped.
Aug 23 22:15:35 tempname kernel: md: unbind<sdd1>
Aug 23 22:15:35 tempname kernel: md: export_rdev(sdd1)
Aug 23 22:15:35 tempname kernel: md: unbind<sdc1>
Aug 23 22:15:35 tempname kernel: md: export_rdev(sdc1)
Aug 23 22:15:35 tempname kernel: md: unbind<sdb1>
Aug 23 22:15:35 tempname kernel: md: export_rdev(sdb1)
Aug 23 22:16:55 tempname kernel: md: bind<sdb1>
Aug 23 22:16:56 tempname kernel: md: bind<sdc1>
Aug 23 22:16:58 tempname kernel: md: bind<sdd1>
Aug 23 22:16:58 tempname kernel: raid5: device sdd1 operational as raid disk 3
Aug 23 22:16:58 tempname kernel: raid5: device sdc1 operational as raid disk 2
Aug 23 22:16:58 tempname kernel: raid5: device sdb1 operational as raid disk 1
Aug 23 22:16:58 tempname kernel: RAID5 conf printout:
Aug 23 22:16:58 tempname kernel: --- rd:4 wd:3
Aug 23 22:16:58 tempname kernel: disk 1, o:1, dev:sdb1
Aug 23 22:16:58 tempname kernel: disk 2, o:1, dev:sdc1
Aug 23 22:16:58 tempname kernel: disk 3, o:1, dev:sdd1
Aug 23 22:16:58 tempname kernel: md: md3 stopped.
Aug 23 22:16:58 tempname kernel: md: unbind<sdd1>
Aug 23 22:16:58 tempname kernel: md: export_rdev(sdd1)
Aug 23 22:16:58 tempname kernel: md: unbind<sdc1>
Aug 23 22:16:58 tempname kernel: md: export_rdev(sdc1)
Aug 23 22:16:58 tempname kernel: md: unbind<sdb1>
Aug 23 22:16:58 tempname kernel: md: export_rdev(sdb1)
Aug 23 22:19:52 tempname kernel: ata1: soft resetting port
Aug 23 22:19:55 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:19:55 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:19:55 tempname kernel: ata1: EH complete
Aug 23 22:19:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:19:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:19:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:26:06 tempname kernel: ata1: soft resetting port
Aug 23 22:26:10 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:26:10 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:26:10 tempname kernel: ata1: EH complete
Aug 23 22:26:10 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:26:10 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:26:10 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:32:22 tempname kernel: ata1: soft resetting port
Aug 23 22:32:25 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:32:25 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:32:25 tempname kernel: ata1: EH complete
Aug 23 22:32:25 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:32:25 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:32:25 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:38:36 tempname kernel: ata1: soft resetting port
Aug 23 22:38:40 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:38:40 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:38:40 tempname kernel: ata1: EH complete
Aug 23 22:38:40 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:38:40 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:38:40 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:44:53 tempname kernel: ata1: soft resetting port
Aug 23 22:44:56 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:44:56 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:44:56 tempname kernel: ata1: EH complete
Aug 23 22:44:56 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:44:56 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:44:56 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:51:07 tempname kernel: ata1: soft resetting port
Aug 23 22:51:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 22:51:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 22:51:11 tempname kernel: ata1: EH complete
Aug 23 22:51:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 22:51:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:51:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:55:10 tempname kernel: Kernel logging (proc) stopped.
Aug 23 22:55:10 tempname kernel: Kernel log daemon terminating.
Aug 23 22:55:11 tempname kernel: klogd 1.5.0#1, log source = /proc/kmsg started.
Aug 23 22:55:12 tempname exiting on signal 15
Aug 23 22:55:12 tempname syslogd 1.5.0#1: restart.
Aug 23 23:00:52 tempname kernel: ata1: soft resetting port
Aug 23 23:00:56 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:00:56 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:00:56 tempname kernel: ata1: EH complete
Aug 23 23:00:56 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:00:56 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:00:56 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:07:08 tempname kernel: ata1: soft resetting port
Aug 23 23:07:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:07:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:07:11 tempname kernel: ata1: EH complete
Aug 23 23:07:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:07:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:07:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:13:22 tempname kernel: ata1: soft resetting port
Aug 23 23:13:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:13:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:13:26 tempname kernel: ata1: EH complete
Aug 23 23:13:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:13:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:13:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:19:38 tempname kernel: ata1: soft resetting port
Aug 23 23:19:41 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:19:42 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:19:42 tempname kernel: ata1: EH complete
Aug 23 23:19:42 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:19:42 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:19:42 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:25:53 tempname kernel: ata1: soft resetting port
Aug 23 23:25:57 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:25:57 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:25:57 tempname kernel: ata1: EH complete
Aug 23 23:25:57 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:25:57 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:25:57 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:32:08 tempname kernel: ata1: soft resetting port
Aug 23 23:32:12 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:32:12 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:32:12 tempname kernel: ata1: EH complete
Aug 23 23:32:12 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:32:12 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:32:12 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:38:24 tempname kernel: ata1: soft resetting port
Aug 23 23:38:27 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:38:28 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:38:28 tempname kernel: ata1: EH complete
Aug 23 23:38:28 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:38:28 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:38:28 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:44:38 tempname kernel: ata1: hard resetting port
Aug 23 23:44:44 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 23 23:44:48 tempname kernel: ata1: hard resetting port
Aug 23 23:44:49 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:44:49 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:44:49 tempname kernel: ata1: EH complete
Aug 23 23:44:49 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:44:49 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:44:49 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:51:01 tempname kernel: ata1: soft resetting port
Aug 23 23:51:05 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:51:05 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:51:05 tempname kernel: ata1: EH complete
Aug 23 23:51:05 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:51:05 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:51:05 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 23:57:16 tempname kernel: ata1: soft resetting port
Aug 23 23:57:20 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 23 23:57:20 tempname kernel: ata1.00: configured for UDMA/100
Aug 23 23:57:20 tempname kernel: ata1: EH complete
Aug 23 23:57:20 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 23 23:57:20 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 23 23:57:20 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:03:31 tempname kernel: ata1: soft resetting port
Aug 24 00:03:34 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:03:34 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:03:34 tempname kernel: ata1: EH complete
Aug 24 00:03:34 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:03:34 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:03:34 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:09:46 tempname kernel: ata1: soft resetting port
Aug 24 00:09:50 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:09:50 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:09:50 tempname kernel: ata1: EH complete
Aug 24 00:09:50 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:09:50 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:09:50 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:16:03 tempname kernel: ata1: soft resetting port
Aug 24 00:16:06 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:16:06 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:16:06 tempname kernel: ata1: EH complete
Aug 24 00:16:06 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:16:06 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:16:06 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:22:18 tempname kernel: ata1: soft resetting port
Aug 24 00:22:22 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:22:22 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:22:22 tempname kernel: ata1: EH complete
Aug 24 00:22:22 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:22:22 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:22:22 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:28:34 tempname kernel: ata1: soft resetting port
Aug 24 00:28:37 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:28:37 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:28:37 tempname kernel: ata1: EH complete
Aug 24 00:28:37 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:28:37 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:28:37 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:34:49 tempname kernel: ata1: soft resetting port
Aug 24 00:34:53 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:34:53 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:34:53 tempname kernel: ata1: EH complete
Aug 24 00:34:53 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:34:53 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:34:53 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:41:04 tempname kernel: ata1: soft resetting port
Aug 24 00:41:07 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:41:07 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:41:07 tempname kernel: ata1: EH complete
Aug 24 00:41:07 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:41:07 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:41:07 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:47:19 tempname kernel: ata1: soft resetting port
Aug 24 00:47:22 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:47:22 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:47:22 tempname kernel: ata1: EH complete
Aug 24 00:47:22 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:47:22 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:47:22 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:53:34 tempname kernel: ata1: soft resetting port
Aug 24 00:53:38 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:53:38 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:53:38 tempname kernel: ata1: EH complete
Aug 24 00:53:38 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:53:38 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:53:38 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 00:59:50 tempname kernel: ata1: soft resetting port
Aug 24 00:59:54 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 00:59:54 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 00:59:54 tempname kernel: ata1: EH complete
Aug 24 00:59:54 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 00:59:54 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 00:59:54 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:06:06 tempname kernel: ata1: soft resetting port
Aug 24 01:06:09 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:06:09 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:06:09 tempname kernel: ata1: EH complete
Aug 24 01:06:09 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:06:09 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:06:09 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:12:21 tempname kernel: ata1: soft resetting port
Aug 24 01:12:25 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:12:25 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:12:25 tempname kernel: ata1: EH complete
Aug 24 01:12:25 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:12:25 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:12:25 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:18:36 tempname kernel: ata1: soft resetting port
Aug 24 01:18:40 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:18:40 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:18:40 tempname kernel: ata1: EH complete
Aug 24 01:18:40 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:18:40 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:18:40 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:24:52 tempname kernel: ata1: soft resetting port
Aug 24 01:24:55 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:24:55 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:24:55 tempname kernel: ata1: EH complete
Aug 24 01:24:55 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:24:55 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:24:55 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:31:07 tempname kernel: ata1: soft resetting port
Aug 24 01:31:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:31:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:31:11 tempname kernel: ata1: EH complete
Aug 24 01:31:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:31:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:31:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:37:23 tempname kernel: ata1: soft resetting port
Aug 24 01:37:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:37:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:37:26 tempname kernel: ata1: EH complete
Aug 24 01:37:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:37:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:37:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:43:39 tempname kernel: ata1: soft resetting port
Aug 24 01:43:43 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:43:43 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:43:43 tempname kernel: ata1: EH complete
Aug 24 01:43:43 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:43:43 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:43:43 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:49:58 tempname kernel: ata1: soft resetting port
Aug 24 01:50:01 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:50:01 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:50:01 tempname kernel: ata1: EH complete
Aug 24 01:50:01 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:50:01 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:50:01 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 01:56:17 tempname kernel: ata1: soft resetting port
Aug 24 01:56:20 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 01:56:20 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 01:56:20 tempname kernel: ata1: EH complete
Aug 24 01:56:20 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 01:56:20 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 01:56:20 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:02:32 tempname kernel: ata1: soft resetting port
Aug 24 02:02:36 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:02:36 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:02:36 tempname kernel: ata1: EH complete
Aug 24 02:02:36 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:02:36 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:02:36 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:08:55 tempname kernel: ata1: hard resetting port
Aug 24 02:09:01 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 24 02:09:05 tempname kernel: ata1: hard resetting port
Aug 24 02:09:06 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:09:06 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:09:06 tempname kernel: ata1: EH complete
Aug 24 02:09:06 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:09:06 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:09:06 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:15:19 tempname kernel: ata1: soft resetting port
Aug 24 02:15:23 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:15:23 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:15:23 tempname kernel: ata1: EH complete
Aug 24 02:15:23 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:15:23 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:15:23 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:21:35 tempname kernel: ata1: soft resetting port
Aug 24 02:21:38 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:21:38 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:21:38 tempname kernel: ata1: EH complete
Aug 24 02:21:38 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:21:38 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:21:38 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:27:50 tempname kernel: ata1: soft resetting port
Aug 24 02:27:54 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:27:54 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:27:54 tempname kernel: ata1: EH complete
Aug 24 02:27:54 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:27:54 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:27:54 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:34:08 tempname kernel: ata1: soft resetting port
Aug 24 02:34:11 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:34:11 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:34:11 tempname kernel: ata1: EH complete
Aug 24 02:34:11 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:34:11 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:34:11 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:40:24 tempname kernel: ata1: soft resetting port
Aug 24 02:40:27 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:40:27 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:40:27 tempname kernel: ata1: EH complete
Aug 24 02:40:27 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:40:27 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:40:27 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:46:47 tempname kernel: ata1: soft resetting port
Aug 24 02:46:51 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:46:51 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:46:51 tempname kernel: ata1: EH complete
Aug 24 02:46:51 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:46:51 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:46:51 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:53:11 tempname kernel: ata1: soft resetting port
Aug 24 02:53:14 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:53:15 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:53:15 tempname kernel: ata1: EH complete
Aug 24 02:53:15 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:53:15 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:53:15 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 02:59:30 tempname kernel: ata1: soft resetting port
Aug 24 02:59:34 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 02:59:34 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 02:59:34 tempname kernel: ata1: EH complete
Aug 24 02:59:34 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 02:59:34 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 02:59:34 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:06:22 tempname kernel: ata1: soft resetting port
Aug 24 03:06:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:06:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:06:26 tempname kernel: ata1: EH complete
Aug 24 03:06:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:06:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:06:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:12:44 tempname kernel: ata1: soft resetting port
Aug 24 03:12:47 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:12:47 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:12:47 tempname kernel: ata1: EH complete
Aug 24 03:12:47 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:12:47 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:12:47 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:33:26 tempname kernel: ata1: soft resetting port
Aug 24 03:33:29 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:33:29 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:33:29 tempname kernel: ata1: EH complete
Aug 24 03:33:29 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:33:29 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:33:29 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:39:44 tempname kernel: ata1: soft resetting port
Aug 24 03:39:47 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:39:47 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:39:47 tempname kernel: ata1: EH complete
Aug 24 03:39:47 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:39:47 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:39:47 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:46:00 tempname kernel: ata1: soft resetting port
Aug 24 03:46:04 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:46:04 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:46:04 tempname kernel: ata1: EH complete
Aug 24 03:46:04 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:46:04 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:46:04 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 03:52:23 tempname kernel: ata1: soft resetting port
Aug 24 03:52:26 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 03:52:26 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 03:52:26 tempname kernel: ata1: EH complete
Aug 24 03:52:26 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 03:52:26 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 03:52:26 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:05:55 tempname kernel: ata1: soft resetting port
Aug 24 04:05:59 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:05:59 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 04:05:59 tempname kernel: ata1: EH complete
Aug 24 04:05:59 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:05:59 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:05:59 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:26:32 tempname kernel: ata1: hard resetting port
Aug 24 04:26:38 tempname kernel: ata1: port is slow to respond, please be patient (Status 0x80)
Aug 24 04:26:42 tempname kernel: ata1: hard resetting port
Aug 24 04:26:43 tempname kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Aug 24 04:26:43 tempname kernel: ata1.00: configured for UDMA/100
Aug 24 04:26:43 tempname kernel: ata1: EH complete
Aug 24 04:26:43 tempname kernel: sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
Aug 24 04:26:43 tempname kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 24 04:26:43 tempname kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 24 04:55:16 tempname -- MARK --
[-- Attachment #3: disk_combinations_causing_reset --]
[-- Type: application/octet-stream, Size: 315 bytes --]
READ: dd if=/dev/sdx of=/dev/null
/dev/sda: reset sda
/dev/sdb: ok
/dev/sdc: ok
/dev/sdd: ok
sdb+sdc: reset sda
sdc+sdd: ok
sdb+sdd: ok
sda+sdb: reset sda (but a lot less frequent)
sda+sdc: reset sda
sda+sdd: reset sda
sda+sdb+sdc: reset sda
sda+sdb+sdd: reset sda
sda+sdc+sdd: reset sda
sdb+sdc+sdd: reset sda
[-- Attachment #4: dmesg_random_collection_of_errors --]
[-- Type: application/octet-stream, Size: 62233 bytes --]
>ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7d:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7d:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:7e:c7/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7e:c7/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7e:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7e:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:7d:c7/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7d:c7/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7d:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7d:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:7e:c7/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7e:c7/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7e:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7e e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851112
printk: 21 messages suppressed.
Buffer I/O error on device sda, logical block 3731389
Buffer I/O error on device sda, logical block 3731390
Buffer I/O error on device sda, logical block 3731391
Buffer I/O error on device sda, logical block 3731392
Buffer I/O error on device sda, logical block 3731393
Buffer I/O error on device sda, logical block 3731394
Buffer I/O error on device sda, logical block 3731395
Buffer I/O error on device sda, logical block 3731396
Buffer I/O error on device sda, logical block 3731397
Buffer I/O error on device sda, logical block 3731398
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7e e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851104
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7e e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851360
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:7e:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:08:e0:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:7d:c7/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:08:e0:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 c7 7d e0
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 29851368
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:7d:c7/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:00:e0:7d:c7/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:a0:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:9f:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:a0:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:9f:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:9f:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:a0:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:9f:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:a0:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:a0:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:9f:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:a0:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:9f:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:9f:39/00:00:03:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:a0:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:9f:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:a0:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:a0:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xe SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:9f:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:a0:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:9f:39/00:00:03:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x6 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:a0:39/00:00:03:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:10:e0:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:9f:39/00:00:03:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:10:e0:9f:39/00:00:03:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
03 39 9f e0
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 54108392
printk: 54 messages suppressed.
Buffer I/O error on device sda, logical block 6763549
Buffer I/O error on device sda, logical block 6763550
Buffer I/O error on device sda, logical block 6763551
Buffer I/O error on device sda, logical block 6763552
Buffer I/O error on device sda, logical block 6763553
Buffer I/O error on device sda, logical block 6763554
Buffer I/O error on device sda, logical block 6763555
Buffer I/O error on device sda, logical block 6763556
Buffer I/O error on device sda, logical block 6763557
Buffer I/O error on device sda, logical block 6763558
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
03 39 9f e0
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 54108128
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x50 SAct 0x0 SErr 0x10800 action 0x6 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: hard resetting port
ata1: port is slow to respond, please be patient (Status 0x80)
ata1: COMRESET failed (errno=-16)
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:3e:da/00:00:02:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:3d:da/00:00:02:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:3e:da/00:00:02:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xe SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:3e:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:3d:da/00:00:02:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:3e:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:3e:da/00:00:02:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:3e:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x6 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:3d:da/00:00:02:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:3d:da/00:00:02:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:08:e0:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:08:e0:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x2 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:3d:da/00:00:02:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:3d:da/00:00:02:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:00:e8:3d:da/00:00:02:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
02 da 3d e8
sd 0:0:0:0: [sda] Add. Sense: No additional sense information
end_request: I/O error, dev sda, sector 47857128
printk: 22 messages suppressed.
Buffer I/O error on device sda, logical block 5982141
Buffer I/O error on device sda, logical block 5982142
Buffer I/O error on device sda, logical block 5982143
Buffer I/O error on device sda, logical block 5982144
Buffer I/O error on device sda, logical block 5982145
Buffer I/O error on device sda, logical block 5982146
Buffer I/O error on device sda, logical block 5982147
Buffer I/O error on device sda, logical block 5982148
Buffer I/O error on device sda, logical block 5982149
Buffer I/O error on device sda, logical block 5982150
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0x2 frozen
ata1: (irq_stat 0x00400000, PHY RDY changed)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xa SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:b7:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:b7:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:b7:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:b7:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:b8:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:b8:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:b8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:b8:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:b8:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:b7:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:b7:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:b7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:b9:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:b9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:b9:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:b9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:c2:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:c2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:c2:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:c2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:c5:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:c5:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:c5:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:c5:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:c7:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:c7:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:c6:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:c6:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:08:e8:c7:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xd SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/00:00:e0:c8:19/01:00:01:00:00/40 tag 0 cdb 0x0 data 131072 in
res 40/00:00:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:c7:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:00:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:c7:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:00:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:c9:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:c9:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:10:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/00:10:e0:c8:19/01:00:01:00:00/40 tag 2 cdb 0x0 data 131072 in
res 40/00:10:e0:c8:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/00:00:e0:c8:19/01:00:01:00:00/40 tag 0 cdb 0x0 data 131072 in
res 40/00:10:e0:c9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:c9:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:10:e0:c9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:c9:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:10:e0:c9:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:cc:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:00:e8:cc:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x2 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/00:08:e0:cd:19/01:00:01:00:00/40 tag 1 cdb 0x0 data 131072 in
res 40/00:08:e0:cd:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xa SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:d2:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:08:e0:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d2:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:08:e0:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:d2:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:d2:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:d3:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d3:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:d3:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:d3:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:d2:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d2:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:d2:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:d4:19/00:00:01:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:d4:19/00:00:01:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:d3:19/00:00:01:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:d3:19/00:00:01:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:d3:19/00:00:01:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x5 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:17:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:17:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:17:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:17:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:18:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:18:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:18:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:18:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:18:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:17:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:17:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:17:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x3 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:19:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:19:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:19:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:19:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xd SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:1b:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:18:e8:1a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:1a:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:1a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:1a:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:1a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xd SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/00:00:e0:1c:64/01:00:04:00:00/40 tag 0 cdb 0x0 data 131072 in
res 40/00:00:e0:1c:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:1b:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:00:e0:1c:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:1b:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:00:e0:1c:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x50 SAct 0xf SErr 0x10800 action 0x6 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:21:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1.00: cmd 60/f8:08:e8:21:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1.00: cmd 60/08:10:e0:22:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:22:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:08:e8:21:64/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
ata1: hard resetting port
ata1: port is slow to respond, please be patient (Status 0x80)
ata1: COMRESET failed (errno=-16)
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:2d:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:2e:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:2d:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:2e:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:10:e8:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xe SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/f8:08:e8:2d:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 126976 in
res 40/00:18:e0:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:10:e0:2e:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e0:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:18:e0:2d:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 4096 in
res 40/00:18:e0:2d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x10000 action 0x2 frozen
ata1.00: (irq_stat 0x00400000, PHY RDY changed)
ata1.00: cmd 60/f8:00:e8:31:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 126976 in
res 40/00:00:e8:31:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xf SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:4d:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/08:08:e0:4e:64/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:4e:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:4d:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:00:e0:4d:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x5 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:77:64/00:00:04:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:77:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:77:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:77:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:7a:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7a:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7a:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0xc SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:10:e0:7b:64/00:00:04:00:00/40 tag 2 cdb 0x0 data 4096 in
res 40/00:18:e8:7b:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:18:e8:7b:64/00:00:04:00:00/40 tag 3 cdb 0x0 data 126976 in
res 40/00:18:e8:7b:64/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x6 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:08:e0:21:cd/00:00:04:00:00/40 tag 1 cdb 0x0 data 4096 in
res 40/00:10:e8:21:cd/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:21:cd/00:00:04:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:21:cd/00:00:04:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x10 SAct 0x5 SErr 0x810000 action 0x2 frozen
ata1.00: (irq_stat 0x08400000, interface fatal error, PHY RDY changed)
ata1.00: cmd 60/08:00:e0:26:b7/00:00:08:00:00/40 tag 0 cdb 0x0 data 4096 in
res 40/00:10:e8:26:b7/00:00:08:00:00/40 Emask 0x10 (ATA bus error)
ata1.00: cmd 60/f8:10:e8:26:b7/00:00:08:00:00/40 tag 2 cdb 0x0 data 126976 in
res 40/00:10:e8:26:b7/00:00:08:00:00/40 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[-- Attachment #5: lsmod --]
[-- Type: application/octet-stream, Size: 2402 bytes --]
Module Size Used by
ppdev 13704 0
parport_pc 42664 0
lp 17352 0
parport 44428 3 ppdev,parport_pc,lp
button 13472 0
ac 10376 0
battery 15496 0
acpi_cpufreq 13704 0
cpufreq_ondemand 13328 4
cpufreq_stats 10400 0
freq_table 9600 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
cpufreq_conservative 12424 0
cpufreq_powersave 6272 0
cpufreq_userspace 9472 0
ipv6 296840 22
ebtable_broute 6656 0
bridge 62760 1 ebtable_broute
ebtable_nat 7040 0
ebtable_filter 6912 0
ebtables 23936 3 ebtable_broute,ebtable_nat,ebtable_filter
dm_snapshot 21320 0
dm_mirror 26240 0
dm_mod 63984 2 dm_snapshot,dm_mirror
coretemp 12544 0
eeprom 12432 0
lm85 39332 0
hwmon_vid 7296 1 lm85
kvm_intel 25232 0
kvm 68688 1 kvm_intel
loop 23044 0
psmouse 45468 0
i2c_i801 13468 0
serio_raw 11780 0
i2c_core 31488 3 eeprom,lm85,i2c_i801
iTCO_wdt 15824 1
pcspkr 7680 0
shpchp 38428 0
pci_hotplug 37252 1 shpchp
evdev 15232 0
ext3 137232 1
jbd 68080 1 ext3
mbcache 13832 1 ext3
raid456 126240 0
md_mod 83996 1 raid456
xor 10256 1 raid456
ata_generic 13188 0
piix 14980 0 [permanent]
sd_mod 33280 4
ahci 28676 2
libata 132016 2 ata_generic,ahci
aic7xxx 162908 1
scsi_transport_spi 31744 1 aic7xxx
ehci_hcd 37900 0
scsi_mod 164536 4 sd_mod,libata,aic7xxx,scsi_transport_spi
generic 10372 0 [permanent]
ide_core 147728 2 piix,generic
floppy 67560 0
e1000 127552 0
uhci_hcd 29856 0
thermal 19600 0
processor 39784 2 acpi_cpufreq,thermal
fan 9992 0
[-- Attachment #6: lspci --]
[-- Type: application/octet-stream, Size: 1912 bytes --]
00:00.0 Host bridge: Intel Corporation E7230/3000/3010 Memory Controller Hub
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 RAID bus controller: Intel Corporation 82801GR/GH (ICH7 Family) Serial ATA Storage Controller RAID (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 PCI bridge: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A (rev 09)
02:02.0 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
02:02.1 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
04:00.3 Serial controller: Intel Corporation Active Management Technology - SOL (rev 03)
04:00.4 Serial bus controller [0c07]: Intel Corporation 82573E KCS (Active Management) (rev 03)
05:04.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
05:05.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
[-- Attachment #7: lspci-v-v --]
[-- Type: application/octet-stream, Size: 20550 bytes --]
00:00.0 Host bridge: Intel Corporation E7230/3000/3010 Memory Controller Hub
Subsystem: Intel Corporation Unknown device 348d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8200000-e82fffff
Prefetchable memory behind bridge: 00000000e8400000-00000000e84fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4159
Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4161
Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e8100000-e81fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 6, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 4080 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 4060 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 4040 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 4020 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at e8300400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation Unknown device 348d
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 40b0 [size=16]
00:1f.2 RAID bus controller: Intel Corporation 82801GR/GH (ICH7 Family) Serial ATA Storage Controller RAID (rev 01)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 1276
Region 0: I/O ports at 40c8 [size=8]
Region 1: I/O ports at 40e4 [size=4]
Region 2: I/O ports at 40c0 [size=8]
Region 3: I/O ports at 40e0 [size=4]
Region 4: I/O ports at 40a0 [size=16]
Region 5: Memory at e8300000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4189
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 4000 [size=32]
01:00.0 PCI bridge: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=02, sec-latency=48
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8200000-e82fffff
Prefetchable memory behind bridge: 00000000e8400000-00000000e84fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=01:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
02:02.0 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
Subsystem: Adaptec AHA-3960D U160/m
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 35
BIST result: 00
Region 0: I/O ports at 3200 [disabled] [size=256]
Region 1: Memory at e8200000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at e8400000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:02.1 SCSI storage controller: Adaptec AHA-3960D / AIC-7899A U160/m (rev 01)
Subsystem: Adaptec AHA-3960D U160/m
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 36
BIST result: 00
Region 0: I/O ports at 3000 [disabled] [size=256]
Region 1: Memory at e8201000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at e8420000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e8180000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 2000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
04:00.3 Serial controller: Intel Corporation Active Management Technology - SOL (rev 03) (prog-if 02 [16550])
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 19
Region 0: I/O ports at 2020 [size=8]
Region 1: Memory at e81a1000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
04:00.4 Serial bus controller [0c07]: Intel Corporation 82573E KCS (Active Management) (rev 03) (prog-if 01)
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at e81a0000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2028 [size=4]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
05:04.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at e8040000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fffe0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:05.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
Subsystem: Intel Corporation Unknown device 348d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e8020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1100 [size=64]
Expansion ROM at e8060000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
^ permalink raw reply [flat|nested] 2+ messages in thread