From: Andrew Liu <shengping.liu@windriver.com>
To: linuxppc-dev <linuxppc-dev@ozlabs.org>
Subject: AMCC yosemite 440ep PCI slot doesn't work.
Date: Fri, 21 Sep 2007 18:53:56 +0800 [thread overview]
Message-ID: <46F3A2C4.7000202@windriver.com> (raw)
Hello All,
when insert a RealTek RTL8139 network card into PCI slot,
After system boot up,
root@localhost:/root> ifconfig eth2 192.168.17.12
irq 25: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
[cf135b20] [c003c414] __report_bad_irq+0x34/0xac
[cf135b40] [c003c714] note_interrupt+0x288/0x2c8
[cf135b70] [c003b818] __do_IRQ+0x104/0x110
[cf135b90] [c0006900] do_IRQ+0xbc/0xc0
[cf135ba0] [c00020c0] ret_from_except+0x0/0x18
[cf135c60] [00000019] 0x19
[cf135c90] [c000668c] do_softirq+0x54/0x58
[cf135ca0] [c001df40] irq_exit+0x48/0x58
[cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
[cf135cc0] [c00020c0] ret_from_except+0x0/0x18
[cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
[cf135da0] [c003c3cc] request_irq+0xc4/0xd8
[cf135dd0] [c0122328] rtl8139_open+0x38/0x210
[cf135df0] [c0187500] dev_open+0x7c/0xcc
[cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
[cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
[cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
[cf135eb0] [c0179328] sock_ioctl+0x60/0x260
[cf135ed0] [c006c360] do_ioctl+0x38/0x84
[cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
[cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
[cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
handlers:
[<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
Disabling IRQ #25
root@localhost:/root>
Message from syslogd@localhost at Thu Jan 1 00:02:13 1970 ...
localhost kernel: Disabling IRQ #25
root@localhost:/root>
The system boot up information as follows:
root@localhost:/root> dmesg
Linux version 2.6.23-rc6-gea60adb5 (sliu@localhost.localdomain) (gcc
version 4.0.0 (DENX ELDK 4.1 4.0.0)) #3 Fri Sep 21 18:37:59 CST 2007
AMCC PowerPC 440EP Yosemite Platform
Entering add_active_range(0, 0, 65536) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 65536
Normal 65536 -> 65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 65536
On node 0 totalpages: 65536
DMA zone: 512 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 65024 pages, LIFO batch:15
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order. Total pages: 65024
Kernel command line: root=/dev/nfs rw
nfsroot=128.224.149.6:/tftpboot/sliu/rootfs
ip=128.224.149.11::128.224.149.1:255.255.255.0:yosemite:eth0:off
console=ttyS0,9600
PID hash table entries: 1024 (order: 10, 4096 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256896k available (2052k kernel code, 716k data, 152k init, 0k
highmem)
Calibrating delay loop... 798.72 BogoMIPS (lpj=1597440)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Scanning bus 0000:00
PCI: Found 0000:00:0c.0 [10ec/8139] 000200 00
PCI: Calling quirk c000444c for 0000:00:0c.0
PCI: Fixups for bus 0000:00
PCI: Bus scan for 0000:00 returning with max=00
PCI: fixup irq: (0000:00:0c.0) got 25
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: Calling quirk c00fbab4 for 0000:00:0c.0
PCI: Calling quirk c02ae3b8 for 0000:00:0c.0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPC 4xx OCP EMAC driver, version 3.54
mal0: initialized, 4 TX channels, 2 RX channels
zmii0: bridge in RMII mode
eth0: emac0, MAC 00:10:ec:00:87:42
eth0: found Generic MII PHY (0x01)
eth1: emac1, MAC 00:00:00:00:00:00
eth1: found Generic MII PHY (0x03)
8139too Fast Ethernet driver 0.9.28
eth2: RealTek RTL8139 at 0xd1012f00, 00:0e:2e:7e:f5:e6, IRQ 25
eth2: Identified 8139 chip type 'RTL-8100B/8139D'
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbmon: debugfs is not available
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ppc-soc-ohci ppc-soc-ohci.0: USB Host Controller
ppc-soc-ohci ppc-soc-ohci.0: new USB bus registered, assigned bus number 1
ppc-soc-ohci ppc-soc-ohci.0: irq 40, io mem 0xef601000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using musbhsfc_udc, OUT ep2 IN ep1 STATUS ep3
usb0: MAC 66:91:74:ab:fb:61
usb0: HOST MAC 1a:b5:87:5d:8f:00
usb0: RNDIS ready
musbhsfc_udc: registered gadget driver 'ether'
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
usb 1-1: new full speed USB device using ppc-soc-ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
eth0: link is up, 100 FDX, pause enabled
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
IP-Config: Complete:
device=eth0, addr=128.224.149.11, mask=255.255.255.0,
gw=128.224.149.1,
host=yosemite, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=128.224.149.6, rootpath=
Looking up port of RPC 100003/2 on 128.224.149.6
Looking up port of RPC 100005/1 on 128.224.149.6
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 152k init
scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 6.16 PQ: 0
ANSI: 0 CCS
sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 244735 512-byte hardware sectors (125 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
irq 25: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[cf135af0] [c0008820] show_stack+0x48/0x190 (unreliable)
[cf135b20] [c003c414] __report_bad_irq+0x34/0xac
[cf135b40] [c003c714] note_interrupt+0x288/0x2c8
[cf135b70] [c003b818] __do_IRQ+0x104/0x110
[cf135b90] [c0006900] do_IRQ+0xbc/0xc0
[cf135ba0] [c00020c0] ret_from_except+0x0/0x18
[cf135c60] [00000019] 0x19
[cf135c90] [c000668c] do_softirq+0x54/0x58
[cf135ca0] [c001df40] irq_exit+0x48/0x58
[cf135cb0] [c00068b4] do_IRQ+0x70/0xc0
[cf135cc0] [c00020c0] ret_from_except+0x0/0x18
[cf135d80] [c003c2b4] setup_irq+0x1ac/0x200
[cf135da0] [c003c3cc] request_irq+0xc4/0xd8
[cf135dd0] [c0122328] rtl8139_open+0x38/0x210
[cf135df0] [c0187500] dev_open+0x7c/0xcc
[cf135e10] [c0187420] dev_change_flags+0x16c/0x1d0
[cf135e30] [c01cbff0] devinet_ioctl+0x604/0x720
[cf135ea0] [c01cc1f8] inet_ioctl+0x98/0xbc
[cf135eb0] [c0179328] sock_ioctl+0x60/0x260
[cf135ed0] [c006c360] do_ioctl+0x38/0x84
[cf135ee0] [c006c438] vfs_ioctl+0x8c/0x40c
[cf135f10] [c006c7f8] sys_ioctl+0x40/0x74
[cf135f40] [c0001a84] ret_from_syscall+0x0/0x3c
handlers:
[<c0122bd4>] (rtl8139_interrupt+0x0/0x52c)
Disabling IRQ #25
eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
Who can give some advice?
Thanks.
BRs,
Andrew.
next reply other threads:[~2007-09-21 15:11 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-21 10:53 Andrew Liu [this message]
2007-09-21 15:14 ` AMCC yosemite 440ep PCI slot doesn't work Valentine Barshak
2007-09-24 9:34 ` Andrew Liu
2007-09-24 11:14 ` Stefan Roese
2007-09-24 11:20 ` Valentine Barshak
2007-09-25 2:05 ` Andrew Liu
2007-09-25 2:02 ` Andrew Liu
2007-09-25 5:18 ` Stefan Roese
2007-09-25 13:21 ` Stefan Roese
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46F3A2C4.7000202@windriver.com \
--to=shengping.liu@windriver.com \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.