* [PATCH ver2] Remove of old NCR53C9x/esp family of drivers
[not found] ` <4731AD56.40206@panasas.com>
@ 2007-11-07 17:01 ` Boaz Harrosh
0 siblings, 0 replies; only message in thread
From: Boaz Harrosh @ 2007-11-07 17:01 UTC (permalink / raw)
To: Maciej W. Rozycki, Christoph Hellwig, David S. Miller,
James Bottomley, zippel
On Wed, Nov 07 2007 at 14:19 +0200, Boaz Harrosh <bharrosh@panasas.com> wrote:
> As recommended by Christoph Hellwig. There is no use
> of fixing these drivers, since there is a much simpler
> and modern esp infrastructure with David Miller's esp_scsi.
> Most of these (mk68) are already broken in other ways.
>
> - Remove all driver files dependent on NCR53C9x.c
I forgot one file sorry, here it is again:
---------------
>From 9ed58af5b0736226a3f836b872fc55118d6b8ee8 Mon Sep 17 00:00:00 2001
From: Boaz Harrosh <bharrosh@panasas.com>
Date: Wed, 7 Nov 2007 18:46:57 +0200
Subject: [PATCH] Remove of old NCR53C9x/esp family of drivers
As recommended by Christoph Hellwig. There is no use
of Fixing these drivers, since there is a much simpler
and modern esp infrastructure with David Miller's esp_scsi
- Remove all driver files dependent on NCR53C9x.c
deleted: drivers/scsi/NCR53C9x.c
deleted: drivers/scsi/NCR53C9x.h
deleted: drivers/scsi/blz1230.c
deleted: drivers/scsi/blz2060.c
deleted: drivers/scsi/cyberstorm.c
deleted: drivers/scsi/cyberstormII.c
deleted: drivers/scsi/dec_esp.c
deleted: drivers/scsi/fastlane.c
deleted: drivers/scsi/mac_esp.c
deleted: drivers/scsi/mca_53c9x.c
deleted: drivers/scsi/oktagon_esp.c
deleted: drivers/scsi/oktagon_io.S
deleted: drivers/scsi/sun3x_esp.c
- Remove above list from drivers/scsi/Kconfig && drivers/scsi/Makefile
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
---
drivers/scsi/Kconfig | 85 -
drivers/scsi/Makefile | 11 -
drivers/scsi/NCR53C9x.c | 3654 -------------------------------------------
drivers/scsi/NCR53C9x.h | 668 --------
drivers/scsi/blz1230.c | 353 -----
drivers/scsi/blz2060.c | 306 ----
drivers/scsi/cyberstorm.c | 377 -----
drivers/scsi/cyberstormII.c | 314 ----
drivers/scsi/dec_esp.c | 687 --------
drivers/scsi/fastlane.c | 421 -----
drivers/scsi/mac_esp.c | 751 ---------
drivers/scsi/mca_53c9x.c | 520 ------
drivers/scsi/oktagon_esp.c | 606 -------
drivers/scsi/oktagon_io.S | 194 ---
drivers/scsi/sun3x_esp.c | 392 -----
15 files changed, 0 insertions(+), 9339 deletions(-)
delete mode 100644 drivers/scsi/NCR53C9x.c
delete mode 100644 drivers/scsi/NCR53C9x.h
delete mode 100644 drivers/scsi/blz1230.c
delete mode 100644 drivers/scsi/blz2060.c
delete mode 100644 drivers/scsi/cyberstorm.c
delete mode 100644 drivers/scsi/cyberstormII.c
delete mode 100644 drivers/scsi/dec_esp.c
delete mode 100644 drivers/scsi/fastlane.c
delete mode 100644 drivers/scsi/mac_esp.c
delete mode 100644 drivers/scsi/mca_53c9x.c
delete mode 100644 drivers/scsi/oktagon_esp.c
delete mode 100644 drivers/scsi/oktagon_io.S
delete mode 100644 drivers/scsi/sun3x_esp.c
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 6e39fa6..e3c8231 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -350,13 +350,6 @@ config SGIWD93_SCSI
If you have a Western Digital WD93 SCSI controller on
an SGI MIPS system, say Y. Otherwise, say N.
-config SCSI_DECNCR
- tristate "DEC NCR53C94 Scsi Driver"
- depends on MACH_DECSTATION && SCSI && TC
- help
- Say Y here to support the NCR53C94 SCSI controller chips on IOASIC
- based TURBOchannel DECstations and TURBOchannel PMAZ-A cards.
-
config SCSI_DECSII
tristate "DEC SII Scsi Driver"
depends on MACH_DECSTATION && SCSI && 32BIT
@@ -1263,17 +1256,6 @@ config SCSI_NCR53C8XX_NO_DISCONNECT
not allow targets to disconnect is not reasonable if there is more
than 1 device on a SCSI bus. The normal answer therefore is N.
-config SCSI_MCA_53C9X
- tristate "NCR MCA 53C9x SCSI support"
- depends on MCA_LEGACY && SCSI && BROKEN_ON_SMP
- help
- Some MicroChannel machines, notably the NCR 35xx line, use a SCSI
- controller based on the NCR 53C94. This driver will allow use of
- the controller on the 3550, and very possibly others.
-
- To compile this driver as a module, choose M here: the
- module will be called mca_53c9x.
-
config SCSI_PAS16
tristate "PAS16 SCSI support"
depends on ISA && SCSI
@@ -1600,45 +1582,6 @@ config GVP11_SCSI
To compile this driver as a module, choose M here: the
module will be called gvp11.
-config CYBERSTORM_SCSI
- tristate "CyberStorm SCSI support"
- depends on ZORRO && SCSI
- help
- If you have an Amiga with an original (MkI) Phase5 Cyberstorm
- accelerator board and the optional Cyberstorm SCSI controller,
- answer Y. Otherwise, say N.
-
-config CYBERSTORMII_SCSI
- tristate "CyberStorm Mk II SCSI support"
- depends on ZORRO && SCSI
- help
- If you have an Amiga with a Phase5 Cyberstorm MkII accelerator board
- and the optional Cyberstorm SCSI controller, say Y. Otherwise,
- answer N.
-
-config BLZ2060_SCSI
- tristate "Blizzard 2060 SCSI support"
- depends on ZORRO && SCSI
- help
- If you have an Amiga with a Phase5 Blizzard 2060 accelerator board
- and want to use the onboard SCSI controller, say Y. Otherwise,
- answer N.
-
-config BLZ1230_SCSI
- tristate "Blizzard 1230IV/1260 SCSI support"
- depends on ZORRO && SCSI
- help
- If you have an Amiga 1200 with a Phase5 Blizzard 1230IV or Blizzard
- 1260 accelerator, and the optional SCSI module, say Y. Otherwise,
- say N.
-
-config FASTLANE_SCSI
- tristate "Fastlane SCSI support"
- depends on ZORRO && SCSI
- help
- If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use
- one in the near future, say Y to this question. Otherwise, say N.
-
config SCSI_A4000T
tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)"
depends on AMIGA && SCSI && EXPERIMENTAL
@@ -1666,15 +1609,6 @@ config SCSI_ZORRO7XX
accelerator card for the Amiga 1200,
- the SCSI controller on the GVP Turbo 040/060 accelerator.
-config OKTAGON_SCSI
- tristate "BSC Oktagon SCSI support (EXPERIMENTAL)"
- depends on ZORRO && SCSI && EXPERIMENTAL
- help
- If you have the BSC Oktagon SCSI disk controller for the Amiga, say
- Y to this question. If you're in doubt about whether you have one,
- see the picture at
- <http://amiga.resource.cx/exp/search.pl?product=oktagon>.
-
config ATARI_SCSI
tristate "Atari native SCSI support"
depends on ATARI && SCSI
@@ -1727,18 +1661,6 @@ config MAC_SCSI
SCSI-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-config SCSI_MAC_ESP
- tristate "Macintosh NCR53c9[46] SCSI"
- depends on MAC && SCSI
- help
- This is the NCR 53c9x SCSI controller found on most of the 68040
- based Macintoshes. If you have one of these say Y and read the
- SCSI-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here: the
- module will be called mac_esp.
-
config MVME147_SCSI
bool "WD33C93 SCSI driver for MVME147"
depends on MVME147 && SCSI=y
@@ -1776,13 +1698,6 @@ config SUN3_SCSI
General Linux information on the Sun 3 series (now discontinued)
is at <http://www.angelfire.com/ca2/tech68k/sun3.html>.
-config SUN3X_ESP
- bool "Sun3x ESP SCSI"
- depends on SUN3X && SCSI=y
- help
- The ESP was an on-board SCSI controller used on Sun 3/80
- machines. Say Y here to compile in support for it.
-
config SCSI_SUNESP
tristate "Sparc ESP Scsi Driver"
depends on SBUS && SCSI
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
index b5441f5..363773e 100644
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -44,15 +44,8 @@ obj-$(CONFIG_A2091_SCSI) += a2091.o wd33c93.o
obj-$(CONFIG_GVP11_SCSI) += gvp11.o wd33c93.o
obj-$(CONFIG_MVME147_SCSI) += mvme147.o wd33c93.o
obj-$(CONFIG_SGIWD93_SCSI) += sgiwd93.o wd33c93.o
-obj-$(CONFIG_CYBERSTORM_SCSI) += NCR53C9x.o cyberstorm.o
-obj-$(CONFIG_CYBERSTORMII_SCSI) += NCR53C9x.o cyberstormII.o
-obj-$(CONFIG_BLZ2060_SCSI) += NCR53C9x.o blz2060.o
-obj-$(CONFIG_BLZ1230_SCSI) += NCR53C9x.o blz1230.o
-obj-$(CONFIG_FASTLANE_SCSI) += NCR53C9x.o fastlane.o
-obj-$(CONFIG_OKTAGON_SCSI) += NCR53C9x.o oktagon_esp_mod.o
obj-$(CONFIG_ATARI_SCSI) += atari_scsi.o
obj-$(CONFIG_MAC_SCSI) += mac_scsi.o
-obj-$(CONFIG_SCSI_MAC_ESP) += mac_esp.o NCR53C9x.o
obj-$(CONFIG_SUN3_SCSI) += sun3_scsi.o sun3_scsi_vme.o
obj-$(CONFIG_MVME16x_SCSI) += 53c700.o mvme16x_scsi.o
obj-$(CONFIG_BVME6000_SCSI) += 53c700.o bvme6000_scsi.o
@@ -95,7 +88,6 @@ obj-$(CONFIG_SCSI_SYM53C8XX_2) += sym53c8xx_2/
obj-$(CONFIG_SCSI_ZALON) += zalon7xx.o
obj-$(CONFIG_SCSI_EATA_PIO) += eata_pio.o
obj-$(CONFIG_SCSI_7000FASST) += wd7000.o
-obj-$(CONFIG_SCSI_MCA_53C9X) += NCR53C9x.o mca_53c9x.o
obj-$(CONFIG_SCSI_IBMMCA) += ibmmca.o
obj-$(CONFIG_SCSI_EATA) += eata.o
obj-$(CONFIG_SCSI_DC395x) += dc395x.o
@@ -112,13 +104,11 @@ obj-$(CONFIG_SCSI_QLOGICPTI) += qlogicpti.o
obj-$(CONFIG_BLK_DEV_IDESCSI) += ide-scsi.o
obj-$(CONFIG_SCSI_MESH) += mesh.o
obj-$(CONFIG_SCSI_MAC53C94) += mac53c94.o
-obj-$(CONFIG_SCSI_DECNCR) += NCR53C9x.o dec_esp.o
obj-$(CONFIG_BLK_DEV_3W_XXXX_RAID) += 3w-xxxx.o
obj-$(CONFIG_SCSI_3W_9XXX) += 3w-9xxx.o
obj-$(CONFIG_SCSI_PPA) += ppa.o
obj-$(CONFIG_SCSI_IMM) += imm.o
obj-$(CONFIG_JAZZ_ESP) += esp_scsi.o jazz_esp.o
-obj-$(CONFIG_SUN3X_ESP) += NCR53C9x.o sun3x_esp.o
obj-$(CONFIG_SCSI_LASI700) += 53c700.o lasi700.o
obj-$(CONFIG_SCSI_SNI_53C710) += 53c700.o sni_53c710.o
obj-$(CONFIG_SCSI_NSP32) += nsp32.o
@@ -162,7 +152,6 @@ ncr53c8xx-flags-$(CONFIG_SCSI_ZALON) \
CFLAGS_ncr53c8xx.o := $(ncr53c8xx-flags-y) $(ncr53c8xx-flags-m)
zalon7xx-objs := zalon.o ncr53c8xx.o
NCR_Q720_mod-objs := NCR_Q720.o ncr53c8xx.o
-oktagon_esp_mod-objs := oktagon_esp.o oktagon_io.o
# Files generated that shall be removed upon make clean
clean-files := 53c700_d.h 53c700_u.h
diff --git a/drivers/scsi/NCR53C9x.c b/drivers/scsi/NCR53C9x.c
deleted file mode 100644
index 5b0efc9..0000000
--- a/drivers/scsi/NCR53C9x.c
+++ /dev/null
@@ -1,3654 +0,0 @@
-/* NCR53C9x.c: Generic SCSI driver code for NCR53C9x chips.
- *
- * Originally esp.c : EnhancedScsiProcessor Sun SCSI driver code.
- *
- * Copyright (C) 1995, 1998 David S. Miller (davem@caip.rutgers.edu)
- *
- * Most DMA dependencies put in driver specific files by
- * Jesper Skov (jskov@cygnus.co.uk)
- *
- * Set up to use esp_read/esp_write (preprocessor macros in NCR53c9x.h) by
- * Tymm Twillman (tymm@coe.missouri.edu)
- */
-
-/* TODO:
- *
- * 1) Maybe disable parity checking in config register one for SCSI1
- * targets. (Gilmore says parity error on the SBus can lock up
- * old sun4c's)
- * 2) Add support for DMA2 pipelining.
- * 3) Add tagged queueing.
- * 4) Maybe change use of "esp" to something more "NCR"'ish.
- */
-
-#include <linux/module.h>
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/interrupt.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/init.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <asm/system.h>
-#include <asm/ptrace.h>
-#include <asm/pgtable.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-
-/* Command phase enumeration. */
-enum {
- not_issued = 0x00, /* Still in the issue_SC queue. */
-
- /* Various forms of selecting a target. */
-#define in_slct_mask 0x10
- in_slct_norm = 0x10, /* ESP is arbitrating, normal selection */
- in_slct_stop = 0x11, /* ESP will select, then stop with IRQ */
- in_slct_msg = 0x12, /* select, then send a message */
- in_slct_tag = 0x13, /* select and send tagged queue msg */
- in_slct_sneg = 0x14, /* select and acquire sync capabilities */
-
- /* Any post selection activity. */
-#define in_phases_mask 0x20
- in_datain = 0x20, /* Data is transferring from the bus */
- in_dataout = 0x21, /* Data is transferring to the bus */
- in_data_done = 0x22, /* Last DMA data operation done (maybe) */
- in_msgin = 0x23, /* Eating message from target */
- in_msgincont = 0x24, /* Eating more msg bytes from target */
- in_msgindone = 0x25, /* Decide what to do with what we got */
- in_msgout = 0x26, /* Sending message to target */
- in_msgoutdone = 0x27, /* Done sending msg out */
- in_cmdbegin = 0x28, /* Sending cmd after abnormal selection */
- in_cmdend = 0x29, /* Done sending slow cmd */
- in_status = 0x2a, /* Was in status phase, finishing cmd */
- in_freeing = 0x2b, /* freeing the bus for cmd cmplt or disc */
- in_the_dark = 0x2c, /* Don't know what bus phase we are in */
-
- /* Special states, ie. not normal bus transitions... */
-#define in_spec_mask 0x80
- in_abortone = 0x80, /* Aborting one command currently */
- in_abortall = 0x81, /* Blowing away all commands we have */
- in_resetdev = 0x82, /* SCSI target reset in progress */
- in_resetbus = 0x83, /* SCSI bus reset in progress */
- in_tgterror = 0x84, /* Target did something stupid */
-};
-
-enum {
- /* Zero has special meaning, see skipahead[12]. */
-/*0*/ do_never,
-
-/*1*/ do_phase_determine,
-/*2*/ do_reset_bus,
-/*3*/ do_reset_complete,
-/*4*/ do_work_bus,
-/*5*/ do_intr_end
-};
-
-/* The master ring of all esp hosts we are managing in this driver. */
-static struct NCR_ESP *espchain;
-int nesps = 0, esps_in_use = 0, esps_running = 0;
-EXPORT_SYMBOL(nesps);
-EXPORT_SYMBOL(esps_running);
-
-irqreturn_t esp_intr(int irq, void *dev_id);
-
-/* Debugging routines */
-static struct esp_cmdstrings {
- unchar cmdchar;
- char *text;
-} esp_cmd_strings[] = {
- /* Miscellaneous */
- { ESP_CMD_NULL, "ESP_NOP", },
- { ESP_CMD_FLUSH, "FIFO_FLUSH", },
- { ESP_CMD_RC, "RSTESP", },
- { ESP_CMD_RS, "RSTSCSI", },
- /* Disconnected State Group */
- { ESP_CMD_RSEL, "RESLCTSEQ", },
- { ESP_CMD_SEL, "SLCTNATN", },
- { ESP_CMD_SELA, "SLCTATN", },
- { ESP_CMD_SELAS, "SLCTATNSTOP", },
- { ESP_CMD_ESEL, "ENSLCTRESEL", },
- { ESP_CMD_DSEL, "DISSELRESEL", },
- { ESP_CMD_SA3, "SLCTATN3", },
- { ESP_CMD_RSEL3, "RESLCTSEQ", },
- /* Target State Group */
- { ESP_CMD_SMSG, "SNDMSG", },
- { ESP_CMD_SSTAT, "SNDSTATUS", },
- { ESP_CMD_SDATA, "SNDDATA", },
- { ESP_CMD_DSEQ, "DISCSEQ", },
- { ESP_CMD_TSEQ, "TERMSEQ", },
- { ESP_CMD_TCCSEQ, "TRGTCMDCOMPSEQ", },
- { ESP_CMD_DCNCT, "DISC", },
- { ESP_CMD_RMSG, "RCVMSG", },
- { ESP_CMD_RCMD, "RCVCMD", },
- { ESP_CMD_RDATA, "RCVDATA", },
- { ESP_CMD_RCSEQ, "RCVCMDSEQ", },
- /* Initiator State Group */
- { ESP_CMD_TI, "TRANSINFO", },
- { ESP_CMD_ICCSEQ, "INICMDSEQCOMP", },
- { ESP_CMD_MOK, "MSGACCEPTED", },
- { ESP_CMD_TPAD, "TPAD", },
- { ESP_CMD_SATN, "SATN", },
- { ESP_CMD_RATN, "RATN", },
-};
-#define NUM_ESP_COMMANDS ((sizeof(esp_cmd_strings)) / (sizeof(struct esp_cmdstrings)))
-
-/* Print textual representation of an ESP command */
-static inline void esp_print_cmd(unchar espcmd)
-{
- unchar dma_bit = espcmd & ESP_CMD_DMA;
- int i;
-
- espcmd &= ~dma_bit;
- for(i=0; i<NUM_ESP_COMMANDS; i++)
- if(esp_cmd_strings[i].cmdchar == espcmd)
- break;
- if(i==NUM_ESP_COMMANDS)
- printk("ESP_Unknown");
- else
- printk("%s%s", esp_cmd_strings[i].text,
- ((dma_bit) ? "+DMA" : ""));
-}
-
-/* Print the status register's value */
-static inline void esp_print_statreg(unchar statreg)
-{
- unchar phase;
-
- printk("STATUS<");
- phase = statreg & ESP_STAT_PMASK;
- printk("%s,", (phase == ESP_DOP ? "DATA-OUT" :
- (phase == ESP_DIP ? "DATA-IN" :
- (phase == ESP_CMDP ? "COMMAND" :
- (phase == ESP_STATP ? "STATUS" :
- (phase == ESP_MOP ? "MSG-OUT" :
- (phase == ESP_MIP ? "MSG_IN" :
- "unknown")))))));
- if(statreg & ESP_STAT_TDONE)
- printk("TRANS_DONE,");
- if(statreg & ESP_STAT_TCNT)
- printk("TCOUNT_ZERO,");
- if(statreg & ESP_STAT_PERR)
- printk("P_ERROR,");
- if(statreg & ESP_STAT_SPAM)
- printk("SPAM,");
- if(statreg & ESP_STAT_INTR)
- printk("IRQ,");
- printk(">");
-}
-
-/* Print the interrupt register's value */
-static inline void esp_print_ireg(unchar intreg)
-{
- printk("INTREG< ");
- if(intreg & ESP_INTR_S)
- printk("SLCT_NATN ");
- if(intreg & ESP_INTR_SATN)
- printk("SLCT_ATN ");
- if(intreg & ESP_INTR_RSEL)
- printk("RSLCT ");
- if(intreg & ESP_INTR_FDONE)
- printk("FDONE ");
- if(intreg & ESP_INTR_BSERV)
- printk("BSERV ");
- if(intreg & ESP_INTR_DC)
- printk("DISCNCT ");
- if(intreg & ESP_INTR_IC)
- printk("ILL_CMD ");
- if(intreg & ESP_INTR_SR)
- printk("SCSI_BUS_RESET ");
- printk(">");
-}
-
-/* Print the sequence step registers contents */
-static inline void esp_print_seqreg(unchar stepreg)
-{
- stepreg &= ESP_STEP_VBITS;
- printk("STEP<%s>",
- (stepreg == ESP_STEP_ASEL ? "SLCT_ARB_CMPLT" :
- (stepreg == ESP_STEP_SID ? "1BYTE_MSG_SENT" :
- (stepreg == ESP_STEP_NCMD ? "NOT_IN_CMD_PHASE" :
- (stepreg == ESP_STEP_PPC ? "CMD_BYTES_LOST" :
- (stepreg == ESP_STEP_FINI4 ? "CMD_SENT_OK" :
- "UNKNOWN"))))));
-}
-
-static char *phase_string(int phase)
-{
- switch(phase) {
- case not_issued:
- return "UNISSUED";
- case in_slct_norm:
- return "SLCTNORM";
- case in_slct_stop:
- return "SLCTSTOP";
- case in_slct_msg:
- return "SLCTMSG";
- case in_slct_tag:
- return "SLCTTAG";
- case in_slct_sneg:
- return "SLCTSNEG";
- case in_datain:
- return "DATAIN";
- case in_dataout:
- return "DATAOUT";
- case in_data_done:
- return "DATADONE";
- case in_msgin:
- return "MSGIN";
- case in_msgincont:
- return "MSGINCONT";
- case in_msgindone:
- return "MSGINDONE";
- case in_msgout:
- return "MSGOUT";
- case in_msgoutdone:
- return "MSGOUTDONE";
- case in_cmdbegin:
- return "CMDBEGIN";
- case in_cmdend:
- return "CMDEND";
- case in_status:
- return "STATUS";
- case in_freeing:
- return "FREEING";
- case in_the_dark:
- return "CLUELESS";
- case in_abortone:
- return "ABORTONE";
- case in_abortall:
- return "ABORTALL";
- case in_resetdev:
- return "RESETDEV";
- case in_resetbus:
- return "RESETBUS";
- case in_tgterror:
- return "TGTERROR";
- default:
- return "UNKNOWN";
- };
-}
-
-#ifdef DEBUG_STATE_MACHINE
-static inline void esp_advance_phase(Scsi_Cmnd *s, int newphase)
-{
- ESPLOG(("<%s>", phase_string(newphase)));
- s->SCp.sent_command = s->SCp.phase;
- s->SCp.phase = newphase;
-}
-#else
-#define esp_advance_phase(__s, __newphase) \
- (__s)->SCp.sent_command = (__s)->SCp.phase; \
- (__s)->SCp.phase = (__newphase);
-#endif
-
-#ifdef DEBUG_ESP_CMDS
-static inline void esp_cmd(struct NCR_ESP *esp, struct ESP_regs *eregs,
- unchar cmd)
-{
- esp->espcmdlog[esp->espcmdent] = cmd;
- esp->espcmdent = (esp->espcmdent + 1) & 31;
- esp_write(eregs->esp_cmnd, cmd);
-}
-#else
-#define esp_cmd(__esp, __eregs, __cmd) esp_write((__eregs)->esp_cmnd, (__cmd))
-#endif
-
-/* How we use the various Linux SCSI data structures for operation.
- *
- * struct scsi_cmnd:
- *
- * We keep track of the syncronous capabilities of a target
- * in the device member, using sync_min_period and
- * sync_max_offset. These are the values we directly write
- * into the ESP registers while running a command. If offset
- * is zero the ESP will use asynchronous transfers.
- * If the borken flag is set we assume we shouldn't even bother
- * trying to negotiate for synchronous transfer as this target
- * is really stupid. If we notice the target is dropping the
- * bus, and we have been allowing it to disconnect, we clear
- * the disconnect flag.
- */
-
-/* Manipulation of the ESP command queues. Thanks to the aha152x driver
- * and its author, Juergen E. Fischer, for the methods used here.
- * Note that these are per-ESP queues, not global queues like
- * the aha152x driver uses.
- */
-static inline void append_SC(Scsi_Cmnd **SC, Scsi_Cmnd *new_SC)
-{
- Scsi_Cmnd *end;
-
- new_SC->host_scribble = (unsigned char *) NULL;
- if(!*SC)
- *SC = new_SC;
- else {
- for(end=*SC;end->host_scribble;end=(Scsi_Cmnd *)end->host_scribble)
- ;
- end->host_scribble = (unsigned char *) new_SC;
- }
-}
-
-static inline void prepend_SC(Scsi_Cmnd **SC, Scsi_Cmnd *new_SC)
-{
- new_SC->host_scribble = (unsigned char *) *SC;
- *SC = new_SC;
-}
-
-static inline Scsi_Cmnd *remove_first_SC(Scsi_Cmnd **SC)
-{
- Scsi_Cmnd *ptr;
-
- ptr = *SC;
- if(ptr)
- *SC = (Scsi_Cmnd *) (*SC)->host_scribble;
- return ptr;
-}
-
-static inline Scsi_Cmnd *remove_SC(Scsi_Cmnd **SC, int target, int lun)
-{
- Scsi_Cmnd *ptr, *prev;
-
- for(ptr = *SC, prev = NULL;
- ptr && ((ptr->device->id != target) || (ptr->device->lun != lun));
- prev = ptr, ptr = (Scsi_Cmnd *) ptr->host_scribble)
- ;
- if(ptr) {
- if(prev)
- prev->host_scribble=ptr->host_scribble;
- else
- *SC=(Scsi_Cmnd *)ptr->host_scribble;
- }
- return ptr;
-}
-
-/* Resetting various pieces of the ESP scsi driver chipset */
-
-/* Reset the ESP chip, _not_ the SCSI bus. */
-static void esp_reset_esp(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- int family_code, version, i;
- volatile int trash;
-
- /* Now reset the ESP chip */
- esp_cmd(esp, eregs, ESP_CMD_RC);
- esp_cmd(esp, eregs, ESP_CMD_NULL | ESP_CMD_DMA);
- if(esp->erev == fast)
- esp_write(eregs->esp_cfg2, ESP_CONFIG2_FENAB);
- esp_cmd(esp, eregs, ESP_CMD_NULL | ESP_CMD_DMA);
-
- /* This is the only point at which it is reliable to read
- * the ID-code for a fast ESP chip variant.
- */
- esp->max_period = ((35 * esp->ccycle) / 1000);
- if(esp->erev == fast) {
- char *erev2string[] = {
- "Emulex FAS236",
- "Emulex FPESP100A",
- "fast",
- "QLogic FAS366",
- "Emulex FAS216",
- "Symbios Logic 53CF9x-2",
- "unknown!"
- };
-
- version = esp_read(eregs->esp_uid);
- family_code = (version & 0xf8) >> 3;
- if(family_code == 0x02) {
- if ((version & 7) == 2)
- esp->erev = fas216;
- else
- esp->erev = fas236;
- } else if(family_code == 0x0a)
- esp->erev = fas366; /* Version is usually '5'. */
- else if(family_code == 0x00) {
- if ((version & 7) == 2)
- esp->erev = fas100a; /* NCR53C9X */
- else
- esp->erev = espunknown;
- } else if(family_code == 0x14) {
- if ((version & 7) == 2)
- esp->erev = fsc;
- else
- esp->erev = espunknown;
- } else if(family_code == 0x00) {
- if ((version & 7) == 2)
- esp->erev = fas100a; /* NCR53C9X */
- else
- esp->erev = espunknown;
- } else
- esp->erev = espunknown;
- ESPLOG(("esp%d: FAST chip is %s (family=%d, version=%d)\n",
- esp->esp_id, erev2string[esp->erev - fas236],
- family_code, (version & 7)));
-
- esp->min_period = ((4 * esp->ccycle) / 1000);
- } else {
- esp->min_period = ((5 * esp->ccycle) / 1000);
- }
-
- /* Reload the configuration registers */
- esp_write(eregs->esp_cfact, esp->cfact);
- esp->prev_stp = 0;
- esp_write(eregs->esp_stp, 0);
- esp->prev_soff = 0;
- esp_write(eregs->esp_soff, 0);
- esp_write(eregs->esp_timeo, esp->neg_defp);
- esp->max_period = (esp->max_period + 3)>>2;
- esp->min_period = (esp->min_period + 3)>>2;
-
- esp_write(eregs->esp_cfg1, esp->config1);
- switch(esp->erev) {
- case esp100:
- /* nothing to do */
- break;
- case esp100a:
- esp_write(eregs->esp_cfg2, esp->config2);
- break;
- case esp236:
- /* Slow 236 */
- esp_write(eregs->esp_cfg2, esp->config2);
- esp->prev_cfg3 = esp->config3[0];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- break;
- case fas366:
- panic("esp: FAS366 support not present, please notify "
- "jongk@cs.utwente.nl");
- break;
- case fas216:
- case fas236:
- case fsc:
- /* Fast ESP variants */
- esp_write(eregs->esp_cfg2, esp->config2);
- for(i=0; i<8; i++)
- esp->config3[i] |= ESP_CONFIG3_FCLK;
- esp->prev_cfg3 = esp->config3[0];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- if(esp->diff)
- esp->radelay = 0;
- else
- esp->radelay = 16;
- /* Different timeout constant for these chips */
- esp->neg_defp =
- FSC_NEG_DEFP(esp->cfreq,
- (esp->cfact == ESP_CCF_F0 ?
- ESP_CCF_F7 + 1 : esp->cfact));
- esp_write(eregs->esp_timeo, esp->neg_defp);
- /* Enable Active Negotiation if possible */
- if((esp->erev == fsc) && !esp->diff)
- esp_write(eregs->esp_cfg4, ESP_CONFIG4_EAN);
- break;
- case fas100a:
- /* Fast 100a */
- esp_write(eregs->esp_cfg2, esp->config2);
- for(i=0; i<8; i++)
- esp->config3[i] |= ESP_CONFIG3_FCLOCK;
- esp->prev_cfg3 = esp->config3[0];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- esp->radelay = 32;
- break;
- default:
- panic("esp: what could it be... I wonder...");
- break;
- };
-
- /* Eat any bitrot in the chip */
- trash = esp_read(eregs->esp_intrpt);
- udelay(100);
-}
-
-/* This places the ESP into a known state at boot time. */
-void esp_bootup_reset(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- volatile unchar trash;
-
- /* Reset the DMA */
- if(esp->dma_reset)
- esp->dma_reset(esp);
-
- /* Reset the ESP */
- esp_reset_esp(esp, eregs);
-
- /* Reset the SCSI bus, but tell ESP not to generate an irq */
- esp_write(eregs->esp_cfg1, (esp_read(eregs->esp_cfg1) | ESP_CONFIG1_SRRDISAB));
- esp_cmd(esp, eregs, ESP_CMD_RS);
- udelay(400);
- esp_write(eregs->esp_cfg1, esp->config1);
-
- /* Eat any bitrot in the chip and we are done... */
- trash = esp_read(eregs->esp_intrpt);
-}
-EXPORT_SYMBOL(esp_bootup_reset);
-
-/* Allocate structure and insert basic data such as SCSI chip frequency
- * data and a pointer to the device
- */
-struct NCR_ESP* esp_allocate(struct scsi_host_template *tpnt, void *esp_dev,
- int hotplug)
-{
- struct NCR_ESP *esp, *elink;
- struct Scsi_Host *esp_host;
-
- if (hotplug)
- esp_host = scsi_host_alloc(tpnt, sizeof(struct NCR_ESP));
- else
- esp_host = scsi_register(tpnt, sizeof(struct NCR_ESP));
- if(!esp_host)
- panic("Cannot register ESP SCSI host");
- esp = (struct NCR_ESP *) esp_host->hostdata;
- if(!esp)
- panic("No esp in hostdata");
- esp->ehost = esp_host;
- esp->edev = esp_dev;
- esp->esp_id = nesps++;
-
- /* Set bitshift value (only used on Amiga with multiple ESPs) */
- esp->shift = 2;
-
- /* Put into the chain of esp chips detected */
- if(espchain) {
- elink = espchain;
- while(elink->next) elink = elink->next;
- elink->next = esp;
- } else {
- espchain = esp;
- }
- esp->next = NULL;
-
- return esp;
-}
-
-void esp_deallocate(struct NCR_ESP *esp)
-{
- struct NCR_ESP *elink;
-
- if(espchain == esp) {
- espchain = NULL;
- } else {
- for(elink = espchain; elink && (elink->next != esp); elink = elink->next);
- if(elink)
- elink->next = esp->next;
- }
- nesps--;
-}
-
-/* Complete initialization of ESP structure and device
- * Caller must have initialized appropriate parts of the ESP structure
- * between the call to esp_allocate and this function.
- */
-void esp_initialize(struct NCR_ESP *esp)
-{
- struct ESP_regs *eregs = esp->eregs;
- unsigned int fmhz;
- unchar ccf;
- int i;
-
- /* Check out the clock properties of the chip. */
-
- /* This is getting messy but it has to be done
- * correctly or else you get weird behavior all
- * over the place. We are trying to basically
- * figure out three pieces of information.
- *
- * a) Clock Conversion Factor
- *
- * This is a representation of the input
- * crystal clock frequency going into the
- * ESP on this machine. Any operation whose
- * timing is longer than 400ns depends on this
- * value being correct. For example, you'll
- * get blips for arbitration/selection during
- * high load or with multiple targets if this
- * is not set correctly.
- *
- * b) Selection Time-Out
- *
- * The ESP isn't very bright and will arbitrate
- * for the bus and try to select a target
- * forever if you let it. This value tells
- * the ESP when it has taken too long to
- * negotiate and that it should interrupt
- * the CPU so we can see what happened.
- * The value is computed as follows (from
- * NCR/Symbios chip docs).
- *
- * (Time Out Period) * (Input Clock)
- * STO = ----------------------------------
- * (8192) * (Clock Conversion Factor)
- *
- * You usually want the time out period to be
- * around 250ms, I think we'll set it a little
- * bit higher to account for fully loaded SCSI
- * bus's and slow devices that don't respond so
- * quickly to selection attempts. (yeah, I know
- * this is out of spec. but there is a lot of
- * buggy pieces of firmware out there so bite me)
- *
- * c) Imperical constants for synchronous offset
- * and transfer period register values
- *
- * This entails the smallest and largest sync
- * period we could ever handle on this ESP.
- */
-
- fmhz = esp->cfreq;
-
- if(fmhz <= (5000000))
- ccf = 0;
- else
- ccf = (((5000000 - 1) + (fmhz))/(5000000));
- if(!ccf || ccf > 8) {
- /* If we can't find anything reasonable,
- * just assume 20MHZ. This is the clock
- * frequency of the older sun4c's where I've
- * been unable to find the clock-frequency
- * PROM property. All other machines provide
- * useful values it seems.
- */
- ccf = ESP_CCF_F4;
- fmhz = (20000000);
- }
- if(ccf==(ESP_CCF_F7+1))
- esp->cfact = ESP_CCF_F0;
- else if(ccf == ESP_CCF_NEVER)
- esp->cfact = ESP_CCF_F2;
- else
- esp->cfact = ccf;
- esp->cfreq = fmhz;
- esp->ccycle = ESP_MHZ_TO_CYCLE(fmhz);
- esp->ctick = ESP_TICK(ccf, esp->ccycle);
- esp->neg_defp = ESP_NEG_DEFP(fmhz, ccf);
- esp->sync_defp = SYNC_DEFP_SLOW;
-
- printk("SCSI ID %d Clk %dMHz CCF=%d TOut %d ",
- esp->scsi_id, (esp->cfreq / 1000000),
- ccf, (int) esp->neg_defp);
-
- /* Fill in ehost data */
- esp->ehost->base = (unsigned long)eregs;
- esp->ehost->this_id = esp->scsi_id;
- esp->ehost->irq = esp->irq;
-
- /* SCSI id mask */
- esp->scsi_id_mask = (1 << esp->scsi_id);
-
- /* Probe the revision of this esp */
- esp->config1 = (ESP_CONFIG1_PENABLE | (esp->scsi_id & 7));
- esp->config2 = (ESP_CONFIG2_SCSI2ENAB | ESP_CONFIG2_REGPARITY);
- esp_write(eregs->esp_cfg2, esp->config2);
- if((esp_read(eregs->esp_cfg2) & ~(ESP_CONFIG2_MAGIC)) !=
- (ESP_CONFIG2_SCSI2ENAB | ESP_CONFIG2_REGPARITY)) {
- printk("NCR53C90(esp100)\n");
- esp->erev = esp100;
- } else {
- esp->config2 = 0;
- esp_write(eregs->esp_cfg2, 0);
- esp_write(eregs->esp_cfg3, 5);
- if(esp_read(eregs->esp_cfg3) != 5) {
- printk("NCR53C90A(esp100a)\n");
- esp->erev = esp100a;
- } else {
- int target;
-
- for(target=0; target<8; target++)
- esp->config3[target] = 0;
- esp->prev_cfg3 = 0;
- esp_write(eregs->esp_cfg3, 0);
- if(ccf > ESP_CCF_F5) {
- printk("NCR53C9XF(espfast)\n");
- esp->erev = fast;
- esp->sync_defp = SYNC_DEFP_FAST;
- } else {
- printk("NCR53C9x(esp236)\n");
- esp->erev = esp236;
- }
- }
- }
-
- /* Initialize the command queues */
- esp->current_SC = NULL;
- esp->disconnected_SC = NULL;
- esp->issue_SC = NULL;
-
- /* Clear the state machines. */
- esp->targets_present = 0;
- esp->resetting_bus = 0;
- esp->snip = 0;
-
- init_waitqueue_head(&esp->reset_queue);
-
- esp->fas_premature_intr_workaround = 0;
- for(i = 0; i < 32; i++)
- esp->espcmdlog[i] = 0;
- esp->espcmdent = 0;
- for(i = 0; i < 16; i++) {
- esp->cur_msgout[i] = 0;
- esp->cur_msgin[i] = 0;
- }
- esp->prevmsgout = esp->prevmsgin = 0;
- esp->msgout_len = esp->msgin_len = 0;
-
- /* Clear the one behind caches to hold unmatchable values. */
- esp->prev_soff = esp->prev_stp = esp->prev_cfg3 = 0xff;
-
- /* Reset the thing before we try anything... */
- esp_bootup_reset(esp, eregs);
-
- esps_in_use++;
-}
-
-/* The info function will return whatever useful
- * information the developer sees fit. If not provided, then
- * the name field will be used instead.
- */
-const char *esp_info(struct Scsi_Host *host)
-{
- struct NCR_ESP *esp;
-
- esp = (struct NCR_ESP *) host->hostdata;
- switch(esp->erev) {
- case esp100:
- return "ESP100 (NCR53C90)";
- case esp100a:
- return "ESP100A (NCR53C90A)";
- case esp236:
- return "ESP236 (NCR53C9x)";
- case fas216:
- return "Emulex FAS216";
- case fas236:
- return "Emulex FAS236";
- case fas366:
- return "QLogic FAS366";
- case fas100a:
- return "FPESP100A";
- case fsc:
- return "Symbios Logic 53CF9x-2";
- default:
- panic("Bogon ESP revision");
- };
-}
-EXPORT_SYMBOL(esp_info);
-
-/* From Wolfgang Stanglmeier's NCR scsi driver. */
-struct info_str
-{
- char *buffer;
- int length;
- int offset;
- int pos;
-};
-
-static void copy_mem_info(struct info_str *info, char *data, int len)
-{
- if (info->pos + len > info->length)
- len = info->length - info->pos;
-
- if (info->pos + len < info->offset) {
- info->pos += len;
- return;
- }
- if (info->pos < info->offset) {
- data += (info->offset - info->pos);
- len -= (info->offset - info->pos);
- }
-
- if (len > 0) {
- memcpy(info->buffer + info->pos, data, len);
- info->pos += len;
- }
-}
-
-static int copy_info(struct info_str *info, char *fmt, ...)
-{
- va_list args;
- char buf[81];
- int len;
-
- va_start(args, fmt);
- len = vsprintf(buf, fmt, args);
- va_end(args);
-
- copy_mem_info(info, buf, len);
- return len;
-}
-
-static int esp_host_info(struct NCR_ESP *esp, char *ptr, off_t offset, int len)
-{
- struct scsi_device *sdev;
- struct info_str info;
- int i;
-
- info.buffer = ptr;
- info.length = len;
- info.offset = offset;
- info.pos = 0;
-
- copy_info(&info, "ESP Host Adapter:\n");
- copy_info(&info, "\tESP Model\t\t");
- switch(esp->erev) {
- case esp100:
- copy_info(&info, "ESP100 (NCR53C90)\n");
- break;
- case esp100a:
- copy_info(&info, "ESP100A (NCR53C90A)\n");
- break;
- case esp236:
- copy_info(&info, "ESP236 (NCR53C9x)\n");
- break;
- case fas216:
- copy_info(&info, "Emulex FAS216\n");
- break;
- case fas236:
- copy_info(&info, "Emulex FAS236\n");
- break;
- case fas100a:
- copy_info(&info, "FPESP100A\n");
- break;
- case fast:
- copy_info(&info, "Generic FAST\n");
- break;
- case fas366:
- copy_info(&info, "QLogic FAS366\n");
- break;
- case fsc:
- copy_info(&info, "Symbios Logic 53C9x-2\n");
- break;
- case espunknown:
- default:
- copy_info(&info, "Unknown!\n");
- break;
- };
- copy_info(&info, "\tLive Targets\t\t[ ");
- for(i = 0; i < 15; i++) {
- if(esp->targets_present & (1 << i))
- copy_info(&info, "%d ", i);
- }
- copy_info(&info, "]\n\n");
-
- /* Now describe the state of each existing target. */
- copy_info(&info, "Target #\tconfig3\t\tSync Capabilities\tDisconnect\n");
-
- shost_for_each_device(sdev, esp->ehost) {
- struct esp_device *esp_dev = sdev->hostdata;
- uint id = sdev->id;
-
- if (!(esp->targets_present & (1 << id)))
- continue;
-
- copy_info(&info, "%d\t\t", id);
- copy_info(&info, "%08lx\t", esp->config3[id]);
- copy_info(&info, "[%02lx,%02lx]\t\t\t",
- esp_dev->sync_max_offset,
- esp_dev->sync_min_period);
- copy_info(&info, "%s\n", esp_dev->disconnect ? "yes" : "no");
- }
-
- return info.pos > info.offset? info.pos - info.offset : 0;
-}
-
-/* ESP proc filesystem code. */
-int esp_proc_info(struct Scsi_Host *shost, char *buffer, char **start, off_t offset, int length,
- int inout)
-{
- struct NCR_ESP *esp = (struct NCR_ESP *)shost->hostdata;
-
- if(inout)
- return -EINVAL; /* not yet */
- if(start)
- *start = buffer;
- return esp_host_info(esp, buffer, offset, length);
-}
-EXPORT_SYMBOL(esp_proc_info);
-
-static void esp_get_dmabufs(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- if(sp->use_sg == 0) {
- sp->SCp.this_residual = sp->request_bufflen;
- sp->SCp.buffer = (struct scatterlist *) sp->request_buffer;
- sp->SCp.buffers_residual = 0;
- if (esp->dma_mmu_get_scsi_one)
- esp->dma_mmu_get_scsi_one(esp, sp);
- else
- sp->SCp.ptr =
- (char *) virt_to_phys(sp->request_buffer);
- } else {
- sp->SCp.buffer = (struct scatterlist *) sp->request_buffer;
- sp->SCp.buffers_residual = sp->use_sg - 1;
- sp->SCp.this_residual = sp->SCp.buffer->length;
- if (esp->dma_mmu_get_scsi_sgl)
- esp->dma_mmu_get_scsi_sgl(esp, sp);
- else
- sp->SCp.ptr =
- (char *) virt_to_phys(sg_virt(sp->SCp.buffer));
- }
-}
-
-static void esp_release_dmabufs(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- if(sp->use_sg == 0) {
- if (esp->dma_mmu_release_scsi_one)
- esp->dma_mmu_release_scsi_one(esp, sp);
- } else {
- if (esp->dma_mmu_release_scsi_sgl)
- esp->dma_mmu_release_scsi_sgl(esp, sp);
- }
-}
-
-static void esp_restore_pointers(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- struct esp_pointers *ep = &esp->data_pointers[scmd_id(sp)];
-
- sp->SCp.ptr = ep->saved_ptr;
- sp->SCp.buffer = ep->saved_buffer;
- sp->SCp.this_residual = ep->saved_this_residual;
- sp->SCp.buffers_residual = ep->saved_buffers_residual;
-}
-
-static void esp_save_pointers(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- struct esp_pointers *ep = &esp->data_pointers[scmd_id(sp)];
-
- ep->saved_ptr = sp->SCp.ptr;
- ep->saved_buffer = sp->SCp.buffer;
- ep->saved_this_residual = sp->SCp.this_residual;
- ep->saved_buffers_residual = sp->SCp.buffers_residual;
-}
-
-/* Some rules:
- *
- * 1) Never ever panic while something is live on the bus.
- * If there is to be any chance of syncing the disks this
- * rule is to be obeyed.
- *
- * 2) Any target that causes a foul condition will no longer
- * have synchronous transfers done to it, no questions
- * asked.
- *
- * 3) Keep register accesses to a minimum. Think about some
- * day when we have Xbus machines this is running on and
- * the ESP chip is on the other end of the machine on a
- * different board from the cpu where this is running.
- */
-
-/* Fire off a command. We assume the bus is free and that the only
- * case where we could see an interrupt is where we have disconnected
- * commands active and they are trying to reselect us.
- */
-static inline void esp_check_cmd(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- switch(sp->cmd_len) {
- case 6:
- case 10:
- case 12:
- esp->esp_slowcmd = 0;
- break;
-
- default:
- esp->esp_slowcmd = 1;
- esp->esp_scmdleft = sp->cmd_len;
- esp->esp_scmdp = &sp->cmnd[0];
- break;
- };
-}
-
-static inline void build_sync_nego_msg(struct NCR_ESP *esp, int period, int offset)
-{
- esp->cur_msgout[0] = EXTENDED_MESSAGE;
- esp->cur_msgout[1] = 3;
- esp->cur_msgout[2] = EXTENDED_SDTR;
- esp->cur_msgout[3] = period;
- esp->cur_msgout[4] = offset;
- esp->msgout_len = 5;
-}
-
-static void esp_exec_cmd(struct NCR_ESP *esp)
-{
- struct ESP_regs *eregs = esp->eregs;
- struct esp_device *esp_dev;
- Scsi_Cmnd *SCptr;
- struct scsi_device *SDptr;
- volatile unchar *cmdp = esp->esp_command;
- unsigned char the_esp_command;
- int lun, target;
- int i;
-
- /* Hold off if we have disconnected commands and
- * an IRQ is showing...
- */
- if(esp->disconnected_SC && esp->dma_irq_p(esp))
- return;
-
- /* Grab first member of the issue queue. */
- SCptr = esp->current_SC = remove_first_SC(&esp->issue_SC);
-
- /* Safe to panic here because current_SC is null. */
- if(!SCptr)
- panic("esp: esp_exec_cmd and issue queue is NULL");
-
- SDptr = SCptr->device;
- esp_dev = SDptr->hostdata;
- lun = SCptr->device->lun;
- target = SCptr->device->id;
-
- esp->snip = 0;
- esp->msgout_len = 0;
-
- /* Send it out whole, or piece by piece? The ESP
- * only knows how to automatically send out 6, 10,
- * and 12 byte commands. I used to think that the
- * Linux SCSI code would never throw anything other
- * than that to us, but then again there is the
- * SCSI generic driver which can send us anything.
- */
- esp_check_cmd(esp, SCptr);
-
- /* If arbitration/selection is successful, the ESP will leave
- * ATN asserted, causing the target to go into message out
- * phase. The ESP will feed the target the identify and then
- * the target can only legally go to one of command,
- * datain/out, status, or message in phase, or stay in message
- * out phase (should we be trying to send a sync negotiation
- * message after the identify). It is not allowed to drop
- * BSY, but some buggy targets do and we check for this
- * condition in the selection complete code. Most of the time
- * we'll make the command bytes available to the ESP and it
- * will not interrupt us until it finishes command phase, we
- * cannot do this for command sizes the ESP does not
- * understand and in this case we'll get interrupted right
- * when the target goes into command phase.
- *
- * It is absolutely _illegal_ in the presence of SCSI-2 devices
- * to use the ESP select w/o ATN command. When SCSI-2 devices are
- * present on the bus we _must_ always go straight to message out
- * phase with an identify message for the target. Being that
- * selection attempts in SCSI-1 w/o ATN was an option, doing SCSI-2
- * selections should not confuse SCSI-1 we hope.
- */
-
- if(esp_dev->sync) {
- /* this targets sync is known */
-#ifdef CONFIG_SCSI_MAC_ESP
-do_sync_known:
-#endif
- if(esp_dev->disconnect)
- *cmdp++ = IDENTIFY(1, lun);
- else
- *cmdp++ = IDENTIFY(0, lun);
-
- if(esp->esp_slowcmd) {
- the_esp_command = (ESP_CMD_SELAS | ESP_CMD_DMA);
- esp_advance_phase(SCptr, in_slct_stop);
- } else {
- the_esp_command = (ESP_CMD_SELA | ESP_CMD_DMA);
- esp_advance_phase(SCptr, in_slct_norm);
- }
- } else if(!(esp->targets_present & (1<<target)) || !(esp_dev->disconnect)) {
- /* After the bootup SCSI code sends both the
- * TEST_UNIT_READY and INQUIRY commands we want
- * to at least attempt allowing the device to
- * disconnect.
- */
- ESPMISC(("esp: Selecting device for first time. target=%d "
- "lun=%d\n", target, SCptr->device->lun));
- if(!SDptr->borken && !esp_dev->disconnect)
- esp_dev->disconnect = 1;
-
- *cmdp++ = IDENTIFY(0, lun);
- esp->prevmsgout = NOP;
- esp_advance_phase(SCptr, in_slct_norm);
- the_esp_command = (ESP_CMD_SELA | ESP_CMD_DMA);
-
- /* Take no chances... */
- esp_dev->sync_max_offset = 0;
- esp_dev->sync_min_period = 0;
- } else {
- int toshiba_cdrom_hwbug_wkaround = 0;
-
-#ifdef CONFIG_SCSI_MAC_ESP
- /* Never allow synchronous transfers (disconnect OK) on
- * Macintosh. Well, maybe later when we figured out how to
- * do DMA on the machines that support it ...
- */
- esp_dev->disconnect = 1;
- esp_dev->sync_max_offset = 0;
- esp_dev->sync_min_period = 0;
- esp_dev->sync = 1;
- esp->snip = 0;
- goto do_sync_known;
-#endif
- /* We've talked to this guy before,
- * but never negotiated. Let's try
- * sync negotiation.
- */
- if(!SDptr->borken) {
- if((SDptr->type == TYPE_ROM) &&
- (!strncmp(SDptr->vendor, "TOSHIBA", 7))) {
- /* Nice try sucker... */
- ESPMISC(("esp%d: Disabling sync for buggy "
- "Toshiba CDROM.\n", esp->esp_id));
- toshiba_cdrom_hwbug_wkaround = 1;
- build_sync_nego_msg(esp, 0, 0);
- } else {
- build_sync_nego_msg(esp, esp->sync_defp, 15);
- }
- } else {
- build_sync_nego_msg(esp, 0, 0);
- }
- esp_dev->sync = 1;
- esp->snip = 1;
-
- /* A fix for broken SCSI1 targets, when they disconnect
- * they lock up the bus and confuse ESP. So disallow
- * disconnects for SCSI1 targets for now until we
- * find a better fix.
- *
- * Addendum: This is funny, I figured out what was going
- * on. The blotzed SCSI1 target would disconnect,
- * one of the other SCSI2 targets or both would be
- * disconnected as well. The SCSI1 target would
- * stay disconnected long enough that we start
- * up a command on one of the SCSI2 targets. As
- * the ESP is arbitrating for the bus the SCSI1
- * target begins to arbitrate as well to reselect
- * the ESP. The SCSI1 target refuses to drop it's
- * ID bit on the data bus even though the ESP is
- * at ID 7 and is the obvious winner for any
- * arbitration. The ESP is a poor sport and refuses
- * to lose arbitration, it will continue indefinitely
- * trying to arbitrate for the bus and can only be
- * stopped via a chip reset or SCSI bus reset.
- * Therefore _no_ disconnects for SCSI1 targets
- * thank you very much. ;-)
- */
- if(((SDptr->scsi_level < 3) && (SDptr->type != TYPE_TAPE)) ||
- toshiba_cdrom_hwbug_wkaround || SDptr->borken) {
- ESPMISC((KERN_INFO "esp%d: Disabling DISCONNECT for target %d "
- "lun %d\n", esp->esp_id, SCptr->device->id, SCptr->device->lun));
- esp_dev->disconnect = 0;
- *cmdp++ = IDENTIFY(0, lun);
- } else {
- *cmdp++ = IDENTIFY(1, lun);
- }
-
- /* ESP fifo is only so big...
- * Make this look like a slow command.
- */
- esp->esp_slowcmd = 1;
- esp->esp_scmdleft = SCptr->cmd_len;
- esp->esp_scmdp = &SCptr->cmnd[0];
-
- the_esp_command = (ESP_CMD_SELAS | ESP_CMD_DMA);
- esp_advance_phase(SCptr, in_slct_msg);
- }
-
- if(!esp->esp_slowcmd)
- for(i = 0; i < SCptr->cmd_len; i++)
- *cmdp++ = SCptr->cmnd[i];
-
- esp_write(eregs->esp_busid, (target & 7));
- if (esp->prev_soff != esp_dev->sync_max_offset ||
- esp->prev_stp != esp_dev->sync_min_period ||
- (esp->erev > esp100a &&
- esp->prev_cfg3 != esp->config3[target])) {
- esp->prev_soff = esp_dev->sync_max_offset;
- esp_write(eregs->esp_soff, esp->prev_soff);
- esp->prev_stp = esp_dev->sync_min_period;
- esp_write(eregs->esp_stp, esp->prev_stp);
- if(esp->erev > esp100a) {
- esp->prev_cfg3 = esp->config3[target];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- }
- }
- i = (cmdp - esp->esp_command);
-
- /* Set up the DMA and ESP counters */
- if(esp->do_pio_cmds){
- int j = 0;
-
- /*
- * XXX MSch:
- *
- * It seems this is required, at least to clean up
- * after failed commands when using PIO mode ...
- */
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
-
- for(;j<i;j++)
- esp_write(eregs->esp_fdata, esp->esp_command[j]);
- the_esp_command &= ~ESP_CMD_DMA;
-
- /* Tell ESP to "go". */
- esp_cmd(esp, eregs, the_esp_command);
- } else {
- /* Set up the ESP counters */
- esp_write(eregs->esp_tclow, i);
- esp_write(eregs->esp_tcmed, 0);
- esp->dma_init_write(esp, esp->esp_command_dvma, i);
-
- /* Tell ESP to "go". */
- esp_cmd(esp, eregs, the_esp_command);
- }
-}
-
-/* Queue a SCSI command delivered from the mid-level Linux SCSI code. */
-int esp_queue(Scsi_Cmnd *SCpnt, void (*done)(Scsi_Cmnd *))
-{
- struct NCR_ESP *esp;
-
- /* Set up func ptr and initial driver cmd-phase. */
- SCpnt->scsi_done = done;
- SCpnt->SCp.phase = not_issued;
-
- esp = (struct NCR_ESP *) SCpnt->device->host->hostdata;
-
- if(esp->dma_led_on)
- esp->dma_led_on(esp);
-
- /* We use the scratch area. */
- ESPQUEUE(("esp_queue: target=%d lun=%d ", SCpnt->device->id, SCpnt->lun));
- ESPDISC(("N<%02x,%02x>", SCpnt->device->id, SCpnt->lun));
-
- esp_get_dmabufs(esp, SCpnt);
- esp_save_pointers(esp, SCpnt); /* FIXME for tag queueing */
-
- SCpnt->SCp.Status = CHECK_CONDITION;
- SCpnt->SCp.Message = 0xff;
- SCpnt->SCp.sent_command = 0;
-
- /* Place into our queue. */
- if(SCpnt->cmnd[0] == REQUEST_SENSE) {
- ESPQUEUE(("RQSENSE\n"));
- prepend_SC(&esp->issue_SC, SCpnt);
- } else {
- ESPQUEUE(("\n"));
- append_SC(&esp->issue_SC, SCpnt);
- }
-
- /* Run it now if we can. */
- if(!esp->current_SC && !esp->resetting_bus)
- esp_exec_cmd(esp);
-
- return 0;
-}
-
-/* Dump driver state. */
-static void esp_dump_cmd(Scsi_Cmnd *SCptr)
-{
- ESPLOG(("[tgt<%02x> lun<%02x> "
- "pphase<%s> cphase<%s>]",
- SCptr->device->id, SCptr->device->lun,
- phase_string(SCptr->SCp.sent_command),
- phase_string(SCptr->SCp.phase)));
-}
-
-static void esp_dump_state(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
-#ifdef DEBUG_ESP_CMDS
- int i;
-#endif
-
- ESPLOG(("esp%d: dumping state\n", esp->esp_id));
-
- /* Print DMA status */
- esp->dma_dump_state(esp);
-
- ESPLOG(("esp%d: SW [sreg<%02x> sstep<%02x> ireg<%02x>]\n",
- esp->esp_id, esp->sreg, esp->seqreg, esp->ireg));
- ESPLOG(("esp%d: HW reread [sreg<%02x> sstep<%02x> ireg<%02x>]\n",
- esp->esp_id, esp_read(eregs->esp_status), esp_read(eregs->esp_sstep),
- esp_read(eregs->esp_intrpt)));
-#ifdef DEBUG_ESP_CMDS
- printk("esp%d: last ESP cmds [", esp->esp_id);
- i = (esp->espcmdent - 1) & 31;
- printk("<");
- esp_print_cmd(esp->espcmdlog[i]);
- printk(">");
- i = (i - 1) & 31;
- printk("<");
- esp_print_cmd(esp->espcmdlog[i]);
- printk(">");
- i = (i - 1) & 31;
- printk("<");
- esp_print_cmd(esp->espcmdlog[i]);
- printk(">");
- i = (i - 1) & 31;
- printk("<");
- esp_print_cmd(esp->espcmdlog[i]);
- printk(">");
- printk("]\n");
-#endif /* (DEBUG_ESP_CMDS) */
-
- if(SCptr) {
- ESPLOG(("esp%d: current command ", esp->esp_id));
- esp_dump_cmd(SCptr);
- }
- ESPLOG(("\n"));
- SCptr = esp->disconnected_SC;
- ESPLOG(("esp%d: disconnected ", esp->esp_id));
- while(SCptr) {
- esp_dump_cmd(SCptr);
- SCptr = (Scsi_Cmnd *) SCptr->host_scribble;
- }
- ESPLOG(("\n"));
-}
-
-/* Abort a command. The host_lock is acquired by caller. */
-int esp_abort(Scsi_Cmnd *SCptr)
-{
- struct NCR_ESP *esp = (struct NCR_ESP *) SCptr->device->host->hostdata;
- struct ESP_regs *eregs = esp->eregs;
- int don;
-
- ESPLOG(("esp%d: Aborting command\n", esp->esp_id));
- esp_dump_state(esp, eregs);
-
- /* Wheee, if this is the current command on the bus, the
- * best we can do is assert ATN and wait for msgout phase.
- * This should even fix a hung SCSI bus when we lose state
- * in the driver and timeout because the eventual phase change
- * will cause the ESP to (eventually) give an interrupt.
- */
- if(esp->current_SC == SCptr) {
- esp->cur_msgout[0] = ABORT;
- esp->msgout_len = 1;
- esp->msgout_ctr = 0;
- esp_cmd(esp, eregs, ESP_CMD_SATN);
- return SUCCESS;
- }
-
- /* If it is still in the issue queue then we can safely
- * call the completion routine and report abort success.
- */
- don = esp->dma_ports_p(esp);
- if(don) {
- esp->dma_ints_off(esp);
- synchronize_irq(esp->irq);
- }
- if(esp->issue_SC) {
- Scsi_Cmnd **prev, *this;
- for(prev = (&esp->issue_SC), this = esp->issue_SC;
- this;
- prev = (Scsi_Cmnd **) &(this->host_scribble),
- this = (Scsi_Cmnd *) this->host_scribble) {
- if(this == SCptr) {
- *prev = (Scsi_Cmnd *) this->host_scribble;
- this->host_scribble = NULL;
- esp_release_dmabufs(esp, this);
- this->result = DID_ABORT << 16;
- this->scsi_done(this);
- if(don)
- esp->dma_ints_on(esp);
- return SUCCESS;
- }
- }
- }
-
- /* Yuck, the command to abort is disconnected, it is not
- * worth trying to abort it now if something else is live
- * on the bus at this time. So, we let the SCSI code wait
- * a little bit and try again later.
- */
- if(esp->current_SC) {
- if(don)
- esp->dma_ints_on(esp);
- return FAILED;
- }
-
- /* It's disconnected, we have to reconnect to re-establish
- * the nexus and tell the device to abort. However, we really
- * cannot 'reconnect' per se. Don't try to be fancy, just
- * indicate failure, which causes our caller to reset the whole
- * bus.
- */
-
- if(don)
- esp->dma_ints_on(esp);
- return FAILED;
-}
-
-/* We've sent ESP_CMD_RS to the ESP, the interrupt had just
- * arrived indicating the end of the SCSI bus reset. Our job
- * is to clean out the command queues and begin re-execution
- * of SCSI commands once more.
- */
-static int esp_finish_reset(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- Scsi_Cmnd *sp = esp->current_SC;
-
- /* Clean up currently executing command, if any. */
- if (sp != NULL) {
- esp_release_dmabufs(esp, sp);
- sp->result = (DID_RESET << 16);
- sp->scsi_done(sp);
- esp->current_SC = NULL;
- }
-
- /* Clean up disconnected queue, they have been invalidated
- * by the bus reset.
- */
- if (esp->disconnected_SC) {
- while((sp = remove_first_SC(&esp->disconnected_SC)) != NULL) {
- esp_release_dmabufs(esp, sp);
- sp->result = (DID_RESET << 16);
- sp->scsi_done(sp);
- }
- }
-
- /* SCSI bus reset is complete. */
- esp->resetting_bus = 0;
- wake_up(&esp->reset_queue);
-
- /* Ok, now it is safe to get commands going once more. */
- if(esp->issue_SC)
- esp_exec_cmd(esp);
-
- return do_intr_end;
-}
-
-static int esp_do_resetbus(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- ESPLOG(("esp%d: Resetting scsi bus\n", esp->esp_id));
- esp->resetting_bus = 1;
- esp_cmd(esp, eregs, ESP_CMD_RS);
-
- return do_intr_end;
-}
-
-/* Reset ESP chip, reset hanging bus, then kill active and
- * disconnected commands for targets without soft reset.
- *
- * The host_lock is acquired by caller.
- */
-int esp_reset(Scsi_Cmnd *SCptr)
-{
- struct NCR_ESP *esp = (struct NCR_ESP *) SCptr->device->host->hostdata;
-
- spin_lock_irq(esp->ehost->host_lock);
- (void) esp_do_resetbus(esp, esp->eregs);
- spin_unlock_irq(esp->ehost->host_lock);
-
- wait_event(esp->reset_queue, (esp->resetting_bus == 0));
-
- return SUCCESS;
-}
-
-/* Internal ESP done function. */
-static void esp_done(struct NCR_ESP *esp, int error)
-{
- Scsi_Cmnd *done_SC;
-
- if(esp->current_SC) {
- done_SC = esp->current_SC;
- esp->current_SC = NULL;
- esp_release_dmabufs(esp, done_SC);
- done_SC->result = error;
- done_SC->scsi_done(done_SC);
-
- /* Bus is free, issue any commands in the queue. */
- if(esp->issue_SC && !esp->current_SC)
- esp_exec_cmd(esp);
- } else {
- /* Panic is safe as current_SC is null so we may still
- * be able to accept more commands to sync disk buffers.
- */
- ESPLOG(("panicing\n"));
- panic("esp: done() called with NULL esp->current_SC");
- }
-}
-
-/* Wheee, ESP interrupt engine. */
-
-/* Forward declarations. */
-static int esp_do_phase_determine(struct NCR_ESP *esp,
- struct ESP_regs *eregs);
-static int esp_do_data_finale(struct NCR_ESP *esp, struct ESP_regs *eregs);
-static int esp_select_complete(struct NCR_ESP *esp, struct ESP_regs *eregs);
-static int esp_do_status(struct NCR_ESP *esp, struct ESP_regs *eregs);
-static int esp_do_msgin(struct NCR_ESP *esp, struct ESP_regs *eregs);
-static int esp_do_msgindone(struct NCR_ESP *esp, struct ESP_regs *eregs);
-static int esp_do_msgout(struct NCR_ESP *esp, struct ESP_regs *eregs);
-static int esp_do_cmdbegin(struct NCR_ESP *esp, struct ESP_regs *eregs);
-
-#define sreg_datainp(__sreg) (((__sreg) & ESP_STAT_PMASK) == ESP_DIP)
-#define sreg_dataoutp(__sreg) (((__sreg) & ESP_STAT_PMASK) == ESP_DOP)
-
-/* We try to avoid some interrupts by jumping ahead and see if the ESP
- * has gotten far enough yet. Hence the following.
- */
-static inline int skipahead1(struct NCR_ESP *esp, struct ESP_regs *eregs,
- Scsi_Cmnd *scp, int prev_phase, int new_phase)
-{
- if(scp->SCp.sent_command != prev_phase)
- return 0;
-
- if(esp->dma_irq_p(esp)) {
- /* Yes, we are able to save an interrupt. */
- esp->sreg = (esp_read(eregs->esp_status) & ~(ESP_STAT_INTR));
- esp->ireg = esp_read(eregs->esp_intrpt);
- if(!(esp->ireg & ESP_INTR_SR))
- return 0;
- else
- return do_reset_complete;
- }
- /* Ho hum, target is taking forever... */
- scp->SCp.sent_command = new_phase; /* so we don't recurse... */
- return do_intr_end;
-}
-
-static inline int skipahead2(struct NCR_ESP *esp,
- struct ESP_regs *eregs,
- Scsi_Cmnd *scp, int prev_phase1, int prev_phase2,
- int new_phase)
-{
- if(scp->SCp.sent_command != prev_phase1 &&
- scp->SCp.sent_command != prev_phase2)
- return 0;
- if(esp->dma_irq_p(esp)) {
- /* Yes, we are able to save an interrupt. */
- esp->sreg = (esp_read(eregs->esp_status) & ~(ESP_STAT_INTR));
- esp->ireg = esp_read(eregs->esp_intrpt);
- if(!(esp->ireg & ESP_INTR_SR))
- return 0;
- else
- return do_reset_complete;
- }
- /* Ho hum, target is taking forever... */
- scp->SCp.sent_command = new_phase; /* so we don't recurse... */
- return do_intr_end;
-}
-
-/* Misc. esp helper macros. */
-#define esp_setcount(__eregs, __cnt) \
- esp_write((__eregs)->esp_tclow, ((__cnt) & 0xff)); \
- esp_write((__eregs)->esp_tcmed, (((__cnt) >> 8) & 0xff))
-
-#define esp_getcount(__eregs) \
- ((esp_read((__eregs)->esp_tclow)&0xff) | \
- ((esp_read((__eregs)->esp_tcmed)&0xff) << 8))
-
-#define fcount(__esp, __eregs) \
- (esp_read((__eregs)->esp_fflags) & ESP_FF_FBYTES)
-
-#define fnzero(__esp, __eregs) \
- (esp_read((__eregs)->esp_fflags) & ESP_FF_ONOTZERO)
-
-/* XXX speculative nops unnecessary when continuing amidst a data phase
- * XXX even on esp100!!! another case of flooding the bus with I/O reg
- * XXX writes...
- */
-#define esp_maybe_nop(__esp, __eregs) \
- if((__esp)->erev == esp100) \
- esp_cmd((__esp), (__eregs), ESP_CMD_NULL)
-
-#define sreg_to_dataphase(__sreg) \
- ((((__sreg) & ESP_STAT_PMASK) == ESP_DOP) ? in_dataout : in_datain)
-
-/* The ESP100 when in synchronous data phase, can mistake a long final
- * REQ pulse from the target as an extra byte, it places whatever is on
- * the data lines into the fifo. For now, we will assume when this
- * happens that the target is a bit quirky and we don't want to
- * be talking synchronously to it anyways. Regardless, we need to
- * tell the ESP to eat the extraneous byte so that we can proceed
- * to the next phase.
- */
-static inline int esp100_sync_hwbug(struct NCR_ESP *esp, struct ESP_regs *eregs,
- Scsi_Cmnd *sp, int fifocnt)
-{
- /* Do not touch this piece of code. */
- if((!(esp->erev == esp100)) ||
- (!(sreg_datainp((esp->sreg = esp_read(eregs->esp_status))) && !fifocnt) &&
- !(sreg_dataoutp(esp->sreg) && !fnzero(esp, eregs)))) {
- if(sp->SCp.phase == in_dataout)
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- return 0;
- } else {
- /* Async mode for this guy. */
- build_sync_nego_msg(esp, 0, 0);
-
- /* Ack the bogus byte, but set ATN first. */
- esp_cmd(esp, eregs, ESP_CMD_SATN);
- esp_cmd(esp, eregs, ESP_CMD_MOK);
- return 1;
- }
-}
-
-/* This closes the window during a selection with a reselect pending, because
- * we use DMA for the selection process the FIFO should hold the correct
- * contents if we get reselected during this process. So we just need to
- * ack the possible illegal cmd interrupt pending on the esp100.
- */
-static inline int esp100_reconnect_hwbug(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- volatile unchar junk;
-
- if(esp->erev != esp100)
- return 0;
- junk = esp_read(eregs->esp_intrpt);
-
- if(junk & ESP_INTR_SR)
- return 1;
- return 0;
-}
-
-/* This verifies the BUSID bits during a reselection so that we know which
- * target is talking to us.
- */
-static inline int reconnect_target(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- int it, me = esp->scsi_id_mask, targ = 0;
-
- if(2 != fcount(esp, eregs))
- return -1;
- it = esp_read(eregs->esp_fdata);
- if(!(it & me))
- return -1;
- it &= ~me;
- if(it & (it - 1))
- return -1;
- while(!(it & 1))
- targ++, it >>= 1;
- return targ;
-}
-
-/* This verifies the identify from the target so that we know which lun is
- * being reconnected.
- */
-static inline int reconnect_lun(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- int lun;
-
- if((esp->sreg & ESP_STAT_PMASK) != ESP_MIP)
- return -1;
- lun = esp_read(eregs->esp_fdata);
-
- /* Yes, you read this correctly. We report lun of zero
- * if we see parity error. ESP reports parity error for
- * the lun byte, and this is the only way to hope to recover
- * because the target is connected.
- */
- if(esp->sreg & ESP_STAT_PERR)
- return 0;
-
- /* Check for illegal bits being set in the lun. */
- if((lun & 0x40) || !(lun & 0x80))
- return -1;
-
- return lun & 7;
-}
-
-/* This puts the driver in a state where it can revitalize a command that
- * is being continued due to reselection.
- */
-static inline void esp_connect(struct NCR_ESP *esp, struct ESP_regs *eregs,
- Scsi_Cmnd *sp)
-{
- struct scsi_device *dp = sp->device;
- struct esp_device *esp_dev = dp->hostdata;
-
- if(esp->prev_soff != esp_dev->sync_max_offset ||
- esp->prev_stp != esp_dev->sync_min_period ||
- (esp->erev > esp100a &&
- esp->prev_cfg3 != esp->config3[scmd_id(sp)])) {
- esp->prev_soff = esp_dev->sync_max_offset;
- esp_write(eregs->esp_soff, esp->prev_soff);
- esp->prev_stp = esp_dev->sync_min_period;
- esp_write(eregs->esp_stp, esp->prev_stp);
- if(esp->erev > esp100a) {
- esp->prev_cfg3 = esp->config3[scmd_id(sp)];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- }
- }
- esp->current_SC = sp;
-}
-
-/* This will place the current working command back into the issue queue
- * if we are to receive a reselection amidst a selection attempt.
- */
-static inline void esp_reconnect(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- if(!esp->disconnected_SC)
- ESPLOG(("esp%d: Weird, being reselected but disconnected "
- "command queue is empty.\n", esp->esp_id));
- esp->snip = 0;
- esp->current_SC = NULL;
- sp->SCp.phase = not_issued;
- append_SC(&esp->issue_SC, sp);
-}
-
-/* Begin message in phase. */
-static int esp_do_msgin(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- esp_maybe_nop(esp, eregs);
- esp_cmd(esp, eregs, ESP_CMD_TI);
- esp->msgin_len = 1;
- esp->msgin_ctr = 0;
- esp_advance_phase(esp->current_SC, in_msgindone);
- return do_work_bus;
-}
-
-static inline void advance_sg(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- ++sp->SCp.buffer;
- --sp->SCp.buffers_residual;
- sp->SCp.this_residual = sp->SCp.buffer->length;
- if (esp->dma_advance_sg)
- esp->dma_advance_sg (sp);
- else
- sp->SCp.ptr = (char *) virt_to_phys(sg_virt(sp->SCp.buffer));
-
-}
-
-/* Please note that the way I've coded these routines is that I _always_
- * check for a disconnect during any and all information transfer
- * phases. The SCSI standard states that the target _can_ cause a BUS
- * FREE condition by dropping all MSG/CD/IO/BSY signals. Also note
- * that during information transfer phases the target controls every
- * change in phase, the only thing the initiator can do is "ask" for
- * a message out phase by driving ATN true. The target can, and sometimes
- * will, completely ignore this request so we cannot assume anything when
- * we try to force a message out phase to abort/reset a target. Most of
- * the time the target will eventually be nice and go to message out, so
- * we may have to hold on to our state about what we want to tell the target
- * for some period of time.
- */
-
-/* I think I have things working here correctly. Even partial transfers
- * within a buffer or sub-buffer should not upset us at all no matter
- * how bad the target and/or ESP fucks things up.
- */
-static int esp_do_data(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- int thisphase, hmuch;
-
- ESPDATA(("esp_do_data: "));
- esp_maybe_nop(esp, eregs);
- thisphase = sreg_to_dataphase(esp->sreg);
- esp_advance_phase(SCptr, thisphase);
- ESPDATA(("newphase<%s> ", (thisphase == in_datain) ? "DATAIN" : "DATAOUT"));
- hmuch = esp->dma_can_transfer(esp, SCptr);
-
- /*
- * XXX MSch: cater for PIO transfer here; PIO used if hmuch == 0
- */
- if (hmuch) { /* DMA */
- /*
- * DMA
- */
- ESPDATA(("hmuch<%d> ", hmuch));
- esp->current_transfer_size = hmuch;
- esp_setcount(eregs, (esp->fas_premature_intr_workaround ?
- (hmuch + 0x40) : hmuch));
- esp->dma_setup(esp, (__u32)((unsigned long)SCptr->SCp.ptr),
- hmuch, (thisphase == in_datain));
- ESPDATA(("DMA|TI --> do_intr_end\n"));
- esp_cmd(esp, eregs, ESP_CMD_DMA | ESP_CMD_TI);
- return do_intr_end;
- /*
- * end DMA
- */
- } else {
- /*
- * PIO
- */
- int oldphase, i = 0; /* or where we left off last time ?? esp->current_data ?? */
- int fifocnt = 0;
- unsigned char *p = phys_to_virt((unsigned long)SCptr->SCp.ptr);
-
- oldphase = esp_read(eregs->esp_status) & ESP_STAT_PMASK;
-
- /*
- * polled transfer; ugly, can we make this happen in a DRQ
- * interrupt handler ??
- * requires keeping track of state information in host or
- * command struct!
- * Problem: I've never seen a DRQ happen on Mac, not even
- * with ESP_CMD_DMA ...
- */
-
- /* figure out how much needs to be transferred */
- hmuch = SCptr->SCp.this_residual;
- ESPDATA(("hmuch<%d> pio ", hmuch));
- esp->current_transfer_size = hmuch;
-
- /* tell the ESP ... */
- esp_setcount(eregs, hmuch);
-
- /* loop */
- while (hmuch) {
- int j, fifo_stuck = 0, newphase;
- unsigned long timeout;
-#if 0
- unsigned long flags;
-#endif
-#if 0
- if ( i % 10 )
- ESPDATA(("\r"));
- else
- ESPDATA(( /*"\n"*/ "\r"));
-#endif
-#if 0
- local_irq_save(flags);
-#endif
- if(thisphase == in_datain) {
- /* 'go' ... */
- esp_cmd(esp, eregs, ESP_CMD_TI);
-
- /* wait for data */
- timeout = 1000000;
- while (!((esp->sreg=esp_read(eregs->esp_status)) & ESP_STAT_INTR) && --timeout)
- udelay(2);
- if (timeout == 0)
- printk("DRQ datain timeout! \n");
-
- newphase = esp->sreg & ESP_STAT_PMASK;
-
- /* see how much we got ... */
- fifocnt = (esp_read(eregs->esp_fflags) & ESP_FF_FBYTES);
-
- if (!fifocnt)
- fifo_stuck++;
- else
- fifo_stuck = 0;
-
- ESPDATA(("\rgot %d st %x ph %x", fifocnt, esp->sreg, newphase));
-
- /* read fifo */
- for(j=0;j<fifocnt;j++)
- p[i++] = esp_read(eregs->esp_fdata);
-
- ESPDATA(("(%d) ", i));
-
- /* how many to go ?? */
- hmuch -= fifocnt;
-
- /* break if status phase !! */
- if(newphase == ESP_STATP) {
- /* clear int. */
- esp->ireg = esp_read(eregs->esp_intrpt);
- break;
- }
- } else {
-#define MAX_FIFO 8
- /* how much will fit ? */
- int this_count = MAX_FIFO - fifocnt;
- if (this_count > hmuch)
- this_count = hmuch;
-
- /* fill fifo */
- for(j=0;j<this_count;j++)
- esp_write(eregs->esp_fdata, p[i++]);
-
- /* how many left if this goes out ?? */
- hmuch -= this_count;
-
- /* 'go' ... */
- esp_cmd(esp, eregs, ESP_CMD_TI);
-
- /* wait for 'got it' */
- timeout = 1000000;
- while (!((esp->sreg=esp_read(eregs->esp_status)) & ESP_STAT_INTR) && --timeout)
- udelay(2);
- if (timeout == 0)
- printk("DRQ dataout timeout! \n");
-
- newphase = esp->sreg & ESP_STAT_PMASK;
-
- /* need to check how much was sent ?? */
- fifocnt = (esp_read(eregs->esp_fflags) & ESP_FF_FBYTES);
-
- ESPDATA(("\rsent %d st %x ph %x", this_count - fifocnt, esp->sreg, newphase));
-
- ESPDATA(("(%d) ", i));
-
- /* break if status phase !! */
- if(newphase == ESP_STATP) {
- /* clear int. */
- esp->ireg = esp_read(eregs->esp_intrpt);
- break;
- }
-
- }
-
- /* clear int. */
- esp->ireg = esp_read(eregs->esp_intrpt);
-
- ESPDATA(("ir %x ... ", esp->ireg));
-
- if (hmuch == 0)
- ESPDATA(("done! \n"));
-
-#if 0
- local_irq_restore(flags);
-#endif
-
- /* check new bus phase */
- if (newphase != oldphase && i < esp->current_transfer_size) {
- /* something happened; disconnect ?? */
- ESPDATA(("phase change, dropped out with %d done ... ", i));
- break;
- }
-
- /* check int. status */
- if (esp->ireg & ESP_INTR_DC) {
- /* disconnect */
- ESPDATA(("disconnect; %d transferred ... ", i));
- break;
- } else if (esp->ireg & ESP_INTR_FDONE) {
- /* function done */
- ESPDATA(("function done; %d transferred ... ", i));
- break;
- }
-
- /* XXX fixme: bail out on stall */
- if (fifo_stuck > 10) {
- /* we're stuck */
- ESPDATA(("fifo stall; %d transferred ... ", i));
- break;
- }
- }
-
- ESPDATA(("\n"));
- /* check successful completion ?? */
-
- if (thisphase == in_dataout)
- hmuch += fifocnt; /* stuck?? adjust data pointer ...*/
-
- /* tell do_data_finale how much was transferred */
- esp->current_transfer_size -= hmuch;
-
- /* still not completely sure on this one ... */
- return /*do_intr_end*/ do_work_bus /*do_phase_determine*/ ;
-
- /*
- * end PIO
- */
- }
- return do_intr_end;
-}
-
-/* See how successful the data transfer was. */
-static int esp_do_data_finale(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- struct esp_device *esp_dev = SCptr->device->hostdata;
- int bogus_data = 0, bytes_sent = 0, fifocnt, ecount = 0;
-
- if(esp->dma_led_off)
- esp->dma_led_off(esp);
-
- ESPDATA(("esp_do_data_finale: "));
-
- if(SCptr->SCp.phase == in_datain) {
- if(esp->sreg & ESP_STAT_PERR) {
- /* Yuck, parity error. The ESP asserts ATN
- * so that we can go to message out phase
- * immediately and inform the target that
- * something bad happened.
- */
- ESPLOG(("esp%d: data bad parity detected.\n",
- esp->esp_id));
- esp->cur_msgout[0] = INITIATOR_ERROR;
- esp->msgout_len = 1;
- }
- if(esp->dma_drain)
- esp->dma_drain(esp);
- }
- if(esp->dma_invalidate)
- esp->dma_invalidate(esp);
-
- /* This could happen for the above parity error case. */
- if(!(esp->ireg == ESP_INTR_BSERV)) {
- /* Please go to msgout phase, please please please... */
- ESPLOG(("esp%d: !BSERV after data, probably to msgout\n",
- esp->esp_id));
- return esp_do_phase_determine(esp, eregs);
- }
-
- /* Check for partial transfers and other horrible events. */
- fifocnt = (esp_read(eregs->esp_fflags) & ESP_FF_FBYTES);
- ecount = esp_getcount(eregs);
- if(esp->fas_premature_intr_workaround)
- ecount -= 0x40;
- bytes_sent = esp->current_transfer_size;
-
- ESPDATA(("trans_sz=%d, ", bytes_sent));
- if(!(esp->sreg & ESP_STAT_TCNT))
- bytes_sent -= ecount;
- if(SCptr->SCp.phase == in_dataout)
- bytes_sent -= fifocnt;
-
- ESPDATA(("bytes_sent=%d (ecount=%d, fifocnt=%d), ", bytes_sent,
- ecount, fifocnt));
-
- /* If we were in synchronous mode, check for peculiarities. */
- if(esp_dev->sync_max_offset)
- bogus_data = esp100_sync_hwbug(esp, eregs, SCptr, fifocnt);
- else
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
-
- /* Until we are sure of what has happened, we are certainly
- * in the dark.
- */
- esp_advance_phase(SCptr, in_the_dark);
-
- /* Check for premature interrupt condition. Can happen on FAS2x6
- * chips. QLogic recommends a workaround by overprogramming the
- * transfer counters, but this makes doing scatter-gather impossible.
- * Until there is a way to disable scatter-gather for a single target,
- * and not only for the entire host adapter as it is now, the workaround
- * is way to expensive performance wise.
- * Instead, it turns out that when this happens the target has disconnected
- * already but it doesn't show in the interrupt register. Compensate for
- * that here to try and avoid a SCSI bus reset.
- */
- if(!esp->fas_premature_intr_workaround && (fifocnt == 1) &&
- sreg_dataoutp(esp->sreg)) {
- ESPLOG(("esp%d: Premature interrupt, enabling workaround\n",
- esp->esp_id));
-#if 0
- /* Disable scatter-gather operations, they are not possible
- * when using this workaround.
- */
- esp->ehost->sg_tablesize = 0;
- esp->ehost->use_clustering = ENABLE_CLUSTERING;
- esp->fas_premature_intr_workaround = 1;
- bytes_sent = 0;
- if(SCptr->use_sg) {
- ESPLOG(("esp%d: Aborting scatter-gather operation\n",
- esp->esp_id));
- esp->cur_msgout[0] = ABORT;
- esp->msgout_len = 1;
- esp->msgout_ctr = 0;
- esp_cmd(esp, eregs, ESP_CMD_SATN);
- esp_setcount(eregs, 0xffff);
- esp_cmd(esp, eregs, ESP_CMD_NULL);
- esp_cmd(esp, eregs, ESP_CMD_TPAD | ESP_CMD_DMA);
- return do_intr_end;
- }
-#else
- /* Just set the disconnected bit. That's what appears to
- * happen anyway. The state machine will pick it up when
- * we return.
- */
- esp->ireg |= ESP_INTR_DC;
-#endif
- }
-
- if(bytes_sent < 0) {
- /* I've seen this happen due to lost state in this
- * driver. No idea why it happened, but allowing
- * this value to be negative caused things to
- * lock up. This allows greater chance of recovery.
- * In fact every time I've seen this, it has been
- * a driver bug without question.
- */
- ESPLOG(("esp%d: yieee, bytes_sent < 0!\n", esp->esp_id));
- ESPLOG(("esp%d: csz=%d fifocount=%d ecount=%d\n",
- esp->esp_id,
- esp->current_transfer_size, fifocnt, ecount));
- ESPLOG(("esp%d: use_sg=%d ptr=%p this_residual=%d\n",
- esp->esp_id,
- SCptr->use_sg, SCptr->SCp.ptr, SCptr->SCp.this_residual));
- ESPLOG(("esp%d: Forcing async for target %d\n", esp->esp_id,
- SCptr->device->id));
- SCptr->device->borken = 1;
- esp_dev->sync = 0;
- bytes_sent = 0;
- }
-
- /* Update the state of our transfer. */
- SCptr->SCp.ptr += bytes_sent;
- SCptr->SCp.this_residual -= bytes_sent;
- if(SCptr->SCp.this_residual < 0) {
- /* shit */
- ESPLOG(("esp%d: Data transfer overrun.\n", esp->esp_id));
- SCptr->SCp.this_residual = 0;
- }
-
- /* Maybe continue. */
- if(!bogus_data) {
- ESPDATA(("!bogus_data, "));
- /* NO MATTER WHAT, we advance the scatterlist,
- * if the target should decide to disconnect
- * in between scatter chunks (which is common)
- * we could die horribly! I used to have the sg
- * advance occur only if we are going back into
- * (or are staying in) a data phase, you can
- * imagine the hell I went through trying to
- * figure this out.
- */
- if(!SCptr->SCp.this_residual && SCptr->SCp.buffers_residual)
- advance_sg(esp, SCptr);
-#ifdef DEBUG_ESP_DATA
- if(sreg_datainp(esp->sreg) || sreg_dataoutp(esp->sreg)) {
- ESPDATA(("to more data\n"));
- } else {
- ESPDATA(("to new phase\n"));
- }
-#endif
- return esp_do_phase_determine(esp, eregs);
- }
- /* Bogus data, just wait for next interrupt. */
- ESPLOG(("esp%d: bogus_data during end of data phase\n",
- esp->esp_id));
- return do_intr_end;
-}
-
-/* We received a non-good status return at the end of
- * running a SCSI command. This is used to decide if
- * we should clear our synchronous transfer state for
- * such a device when that happens.
- *
- * The idea is that when spinning up a disk or rewinding
- * a tape, we don't want to go into a loop re-negotiating
- * synchronous capabilities over and over.
- */
-static int esp_should_clear_sync(Scsi_Cmnd *sp)
-{
- unchar cmd = sp->cmnd[0];
-
- /* These cases are for spinning up a disk and
- * waiting for that spinup to complete.
- */
- if(cmd == START_STOP)
- return 0;
-
- if(cmd == TEST_UNIT_READY)
- return 0;
-
- /* One more special case for SCSI tape drives,
- * this is what is used to probe the device for
- * completion of a rewind or tape load operation.
- */
- if(sp->device->type == TYPE_TAPE && cmd == MODE_SENSE)
- return 0;
-
- return 1;
-}
-
-/* Either a command is completing or a target is dropping off the bus
- * to continue the command in the background so we can do other work.
- */
-static int esp_do_freebus(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- int rval;
-
- rval = skipahead2(esp, eregs, SCptr, in_status, in_msgindone, in_freeing);
- if(rval)
- return rval;
-
- if(esp->ireg != ESP_INTR_DC) {
- ESPLOG(("esp%d: Target will not disconnect\n", esp->esp_id));
- return do_reset_bus; /* target will not drop BSY... */
- }
- esp->msgout_len = 0;
- esp->prevmsgout = NOP;
- if(esp->prevmsgin == COMMAND_COMPLETE) {
- struct esp_device *esp_dev = SCptr->device->hostdata;
- /* Normal end of nexus. */
- if(esp->disconnected_SC)
- esp_cmd(esp, eregs, ESP_CMD_ESEL);
-
- if(SCptr->SCp.Status != GOOD &&
- SCptr->SCp.Status != CONDITION_GOOD &&
- ((1<<scmd_id(SCptr)) & esp->targets_present) &&
- esp_dev->sync && esp_dev->sync_max_offset) {
- /* SCSI standard says that the synchronous capabilities
- * should be renegotiated at this point. Most likely
- * we are about to request sense from this target
- * in which case we want to avoid using sync
- * transfers until we are sure of the current target
- * state.
- */
- ESPMISC(("esp: Status <%d> for target %d lun %d\n",
- SCptr->SCp.Status, SCptr->device->id, SCptr->device->lun));
-
- /* But don't do this when spinning up a disk at
- * boot time while we poll for completion as it
- * fills up the console with messages. Also, tapes
- * can report not ready many times right after
- * loading up a tape.
- */
- if(esp_should_clear_sync(SCptr) != 0)
- esp_dev->sync = 0;
- }
- ESPDISC(("F<%02x,%02x>", SCptr->device->id, SCptr->device->lun));
- esp_done(esp, ((SCptr->SCp.Status & 0xff) |
- ((SCptr->SCp.Message & 0xff)<<8) |
- (DID_OK << 16)));
- } else if(esp->prevmsgin == DISCONNECT) {
- /* Normal disconnect. */
- esp_cmd(esp, eregs, ESP_CMD_ESEL);
- ESPDISC(("D<%02x,%02x>", SCptr->device->id, SCptr->device->lun));
- append_SC(&esp->disconnected_SC, SCptr);
- esp->current_SC = NULL;
- if(esp->issue_SC)
- esp_exec_cmd(esp);
- } else {
- /* Driver bug, we do not expect a disconnect here
- * and should not have advanced the state engine
- * to in_freeing.
- */
- ESPLOG(("esp%d: last msg not disc and not cmd cmplt.\n",
- esp->esp_id));
- return do_reset_bus;
- }
- return do_intr_end;
-}
-
-/* When a reselect occurs, and we cannot find the command to
- * reconnect to in our queues, we do this.
- */
-static int esp_bad_reconnect(struct NCR_ESP *esp)
-{
- Scsi_Cmnd *sp;
-
- ESPLOG(("esp%d: Eieeee, reconnecting unknown command!\n",
- esp->esp_id));
- ESPLOG(("QUEUE DUMP\n"));
- sp = esp->issue_SC;
- ESPLOG(("esp%d: issue_SC[", esp->esp_id));
- while(sp) {
- ESPLOG(("<%02x,%02x>", sp->device->id, sp->device->lun));
- sp = (Scsi_Cmnd *) sp->host_scribble;
- }
- ESPLOG(("]\n"));
- sp = esp->current_SC;
- ESPLOG(("esp%d: current_SC[", esp->esp_id));
- while(sp) {
- ESPLOG(("<%02x,%02x>", sp->device->id, sp->device->lun));
- sp = (Scsi_Cmnd *) sp->host_scribble;
- }
- ESPLOG(("]\n"));
- sp = esp->disconnected_SC;
- ESPLOG(("esp%d: disconnected_SC[", esp->esp_id));
- while(sp) {
- ESPLOG(("<%02x,%02x>", sp->device->id, sp->device->lun));
- sp = (Scsi_Cmnd *) sp->host_scribble;
- }
- ESPLOG(("]\n"));
- return do_reset_bus;
-}
-
-/* Do the needy when a target tries to reconnect to us. */
-static int esp_do_reconnect(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- int lun, target;
- Scsi_Cmnd *SCptr;
-
- /* Check for all bogus conditions first. */
- target = reconnect_target(esp, eregs);
- if(target < 0) {
- ESPDISC(("bad bus bits\n"));
- return do_reset_bus;
- }
- lun = reconnect_lun(esp, eregs);
- if(lun < 0) {
- ESPDISC(("target=%2x, bad identify msg\n", target));
- return do_reset_bus;
- }
-
- /* Things look ok... */
- ESPDISC(("R<%02x,%02x>", target, lun));
-
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- if(esp100_reconnect_hwbug(esp, eregs))
- return do_reset_bus;
- esp_cmd(esp, eregs, ESP_CMD_NULL);
-
- SCptr = remove_SC(&esp->disconnected_SC, (unchar) target, (unchar) lun);
- if(!SCptr)
- return esp_bad_reconnect(esp);
-
- esp_connect(esp, eregs, SCptr);
- esp_cmd(esp, eregs, ESP_CMD_MOK);
-
- /* Reconnect implies a restore pointers operation. */
- esp_restore_pointers(esp, SCptr);
-
- esp->snip = 0;
- esp_advance_phase(SCptr, in_the_dark);
- return do_intr_end;
-}
-
-/* End of NEXUS (hopefully), pick up status + message byte then leave if
- * all goes well.
- */
-static int esp_do_status(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- int intr, rval;
-
- rval = skipahead1(esp, eregs, SCptr, in_the_dark, in_status);
- if(rval)
- return rval;
-
- intr = esp->ireg;
- ESPSTAT(("esp_do_status: "));
- if(intr != ESP_INTR_DC) {
- int message_out = 0; /* for parity problems */
-
- /* Ack the message. */
- ESPSTAT(("ack msg, "));
- esp_cmd(esp, eregs, ESP_CMD_MOK);
-
- if(esp->dma_poll)
- esp->dma_poll(esp, (unsigned char *) esp->esp_command);
-
- ESPSTAT(("got something, "));
- /* ESP chimes in with one of
- *
- * 1) function done interrupt:
- * both status and message in bytes
- * are available
- *
- * 2) bus service interrupt:
- * only status byte was acquired
- *
- * 3) Anything else:
- * can't happen, but we test for it
- * anyways
- *
- * ALSO: If bad parity was detected on either
- * the status _or_ the message byte then
- * the ESP has asserted ATN on the bus
- * and we must therefore wait for the
- * next phase change.
- */
- if(intr & ESP_INTR_FDONE) {
- /* We got it all, hallejulia. */
- ESPSTAT(("got both, "));
- SCptr->SCp.Status = esp->esp_command[0];
- SCptr->SCp.Message = esp->esp_command[1];
- esp->prevmsgin = SCptr->SCp.Message;
- esp->cur_msgin[0] = SCptr->SCp.Message;
- if(esp->sreg & ESP_STAT_PERR) {
- /* There was bad parity for the
- * message byte, the status byte
- * was ok.
- */
- message_out = MSG_PARITY_ERROR;
- }
- } else if(intr == ESP_INTR_BSERV) {
- /* Only got status byte. */
- ESPLOG(("esp%d: got status only, ", esp->esp_id));
- if(!(esp->sreg & ESP_STAT_PERR)) {
- SCptr->SCp.Status = esp->esp_command[0];
- SCptr->SCp.Message = 0xff;
- } else {
- /* The status byte had bad parity.
- * we leave the scsi_pointer Status
- * field alone as we set it to a default
- * of CHECK_CONDITION in esp_queue.
- */
- message_out = INITIATOR_ERROR;
- }
- } else {
- /* This shouldn't happen ever. */
- ESPSTAT(("got bolixed\n"));
- esp_advance_phase(SCptr, in_the_dark);
- return esp_do_phase_determine(esp, eregs);
- }
-
- if(!message_out) {
- ESPSTAT(("status=%2x msg=%2x, ", SCptr->SCp.Status,
- SCptr->SCp.Message));
- if(SCptr->SCp.Message == COMMAND_COMPLETE) {
- ESPSTAT(("and was COMMAND_COMPLETE\n"));
- esp_advance_phase(SCptr, in_freeing);
- return esp_do_freebus(esp, eregs);
- } else {
- ESPLOG(("esp%d: and _not_ COMMAND_COMPLETE\n",
- esp->esp_id));
- esp->msgin_len = esp->msgin_ctr = 1;
- esp_advance_phase(SCptr, in_msgindone);
- return esp_do_msgindone(esp, eregs);
- }
- } else {
- /* With luck we'll be able to let the target
- * know that bad parity happened, it will know
- * which byte caused the problems and send it
- * again. For the case where the status byte
- * receives bad parity, I do not believe most
- * targets recover very well. We'll see.
- */
- ESPLOG(("esp%d: bad parity somewhere mout=%2x\n",
- esp->esp_id, message_out));
- esp->cur_msgout[0] = message_out;
- esp->msgout_len = esp->msgout_ctr = 1;
- esp_advance_phase(SCptr, in_the_dark);
- return esp_do_phase_determine(esp, eregs);
- }
- } else {
- /* If we disconnect now, all hell breaks loose. */
- ESPLOG(("esp%d: whoops, disconnect\n", esp->esp_id));
- esp_advance_phase(SCptr, in_the_dark);
- return esp_do_phase_determine(esp, eregs);
- }
-}
-
-static int esp_enter_status(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- unchar thecmd = ESP_CMD_ICCSEQ;
-
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
-
- if(esp->do_pio_cmds) {
- esp_advance_phase(esp->current_SC, in_status);
- esp_cmd(esp, eregs, thecmd);
- while(!(esp_read(esp->eregs->esp_status) & ESP_STAT_INTR));
- esp->esp_command[0] = esp_read(eregs->esp_fdata);
- while(!(esp_read(esp->eregs->esp_status) & ESP_STAT_INTR));
- esp->esp_command[1] = esp_read(eregs->esp_fdata);
- } else {
- esp->esp_command[0] = esp->esp_command[1] = 0xff;
- esp_write(eregs->esp_tclow, 2);
- esp_write(eregs->esp_tcmed, 0);
- esp->dma_init_read(esp, esp->esp_command_dvma, 2);
- thecmd |= ESP_CMD_DMA;
- esp_cmd(esp, eregs, thecmd);
- esp_advance_phase(esp->current_SC, in_status);
- }
-
- return esp_do_status(esp, eregs);
-}
-
-static int esp_disconnect_amidst_phases(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- Scsi_Cmnd *sp = esp->current_SC;
- struct esp_device *esp_dev = sp->device->hostdata;
-
- /* This means real problems if we see this
- * here. Unless we were actually trying
- * to force the device to abort/reset.
- */
- ESPLOG(("esp%d: Disconnect amidst phases, ", esp->esp_id));
- ESPLOG(("pphase<%s> cphase<%s>, ",
- phase_string(sp->SCp.phase),
- phase_string(sp->SCp.sent_command)));
-
- if(esp->disconnected_SC)
- esp_cmd(esp, eregs, ESP_CMD_ESEL);
-
- switch(esp->cur_msgout[0]) {
- default:
- /* We didn't expect this to happen at all. */
- ESPLOG(("device is bolixed\n"));
- esp_advance_phase(sp, in_tgterror);
- esp_done(esp, (DID_ERROR << 16));
- break;
-
- case BUS_DEVICE_RESET:
- ESPLOG(("device reset successful\n"));
- esp_dev->sync_max_offset = 0;
- esp_dev->sync_min_period = 0;
- esp_dev->sync = 0;
- esp_advance_phase(sp, in_resetdev);
- esp_done(esp, (DID_RESET << 16));
- break;
-
- case ABORT:
- ESPLOG(("device abort successful\n"));
- esp_advance_phase(sp, in_abortone);
- esp_done(esp, (DID_ABORT << 16));
- break;
-
- };
- return do_intr_end;
-}
-
-static int esp_enter_msgout(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- esp_advance_phase(esp->current_SC, in_msgout);
- return esp_do_msgout(esp, eregs);
-}
-
-static int esp_enter_msgin(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- esp_advance_phase(esp->current_SC, in_msgin);
- return esp_do_msgin(esp, eregs);
-}
-
-static int esp_enter_cmd(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- esp_advance_phase(esp->current_SC, in_cmdbegin);
- return esp_do_cmdbegin(esp, eregs);
-}
-
-static int esp_enter_badphase(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- ESPLOG(("esp%d: Bizarre bus phase %2x.\n", esp->esp_id,
- esp->sreg & ESP_STAT_PMASK));
- return do_reset_bus;
-}
-
-typedef int (*espfunc_t)(struct NCR_ESP *,
- struct ESP_regs *);
-
-static espfunc_t phase_vector[] = {
- esp_do_data, /* ESP_DOP */
- esp_do_data, /* ESP_DIP */
- esp_enter_cmd, /* ESP_CMDP */
- esp_enter_status, /* ESP_STATP */
- esp_enter_badphase, /* ESP_STAT_PMSG */
- esp_enter_badphase, /* ESP_STAT_PMSG | ESP_STAT_PIO */
- esp_enter_msgout, /* ESP_MOP */
- esp_enter_msgin, /* ESP_MIP */
-};
-
-/* The target has control of the bus and we have to see where it has
- * taken us.
- */
-static int esp_do_phase_determine(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- if ((esp->ireg & ESP_INTR_DC) != 0)
- return esp_disconnect_amidst_phases(esp, eregs);
- return phase_vector[esp->sreg & ESP_STAT_PMASK](esp, eregs);
-}
-
-/* First interrupt after exec'ing a cmd comes here. */
-static int esp_select_complete(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- struct esp_device *esp_dev = SCptr->device->hostdata;
- int cmd_bytes_sent, fcnt;
-
- fcnt = (esp_read(eregs->esp_fflags) & ESP_FF_FBYTES);
- cmd_bytes_sent = esp->dma_bytes_sent(esp, fcnt);
- if(esp->dma_invalidate)
- esp->dma_invalidate(esp);
-
- /* Let's check to see if a reselect happened
- * while we we're trying to select. This must
- * be checked first.
- */
- if(esp->ireg == (ESP_INTR_RSEL | ESP_INTR_FDONE)) {
- esp_reconnect(esp, SCptr);
- return esp_do_reconnect(esp, eregs);
- }
-
- /* Looks like things worked, we should see a bus service &
- * a function complete interrupt at this point. Note we
- * are doing a direct comparison because we don't want to
- * be fooled into thinking selection was successful if
- * ESP_INTR_DC is set, see below.
- */
- if(esp->ireg == (ESP_INTR_FDONE | ESP_INTR_BSERV)) {
- /* target speaks... */
- esp->targets_present |= (1<<scmd_id(SCptr));
-
- /* What if the target ignores the sdtr? */
- if(esp->snip)
- esp_dev->sync = 1;
-
- /* See how far, if at all, we got in getting
- * the information out to the target.
- */
- switch(esp->seqreg) {
- default:
-
- case ESP_STEP_ASEL:
- /* Arbitration won, target selected, but
- * we are in some phase which is not command
- * phase nor is it message out phase.
- *
- * XXX We've confused the target, obviously.
- * XXX So clear it's state, but we also end
- * XXX up clearing everyone elses. That isn't
- * XXX so nice. I'd like to just reset this
- * XXX target, but if I cannot even get it's
- * XXX attention and finish selection to talk
- * XXX to it, there is not much more I can do.
- * XXX If we have a loaded bus we're going to
- * XXX spend the next second or so renegotiating
- * XXX for synchronous transfers.
- */
- ESPLOG(("esp%d: STEP_ASEL for tgt %d\n",
- esp->esp_id, SCptr->device->id));
-
- case ESP_STEP_SID:
- /* Arbitration won, target selected, went
- * to message out phase, sent one message
- * byte, then we stopped. ATN is asserted
- * on the SCSI bus and the target is still
- * there hanging on. This is a legal
- * sequence step if we gave the ESP a select
- * and stop command.
- *
- * XXX See above, I could set the borken flag
- * XXX in the device struct and retry the
- * XXX command. But would that help for
- * XXX tagged capable targets?
- */
-
- case ESP_STEP_NCMD:
- /* Arbitration won, target selected, maybe
- * sent the one message byte in message out
- * phase, but we did not go to command phase
- * in the end. Actually, we could have sent
- * only some of the message bytes if we tried
- * to send out the entire identify and tag
- * message using ESP_CMD_SA3.
- */
- cmd_bytes_sent = 0;
- break;
-
- case ESP_STEP_PPC:
- /* No, not the powerPC pinhead. Arbitration
- * won, all message bytes sent if we went to
- * message out phase, went to command phase
- * but only part of the command was sent.
- *
- * XXX I've seen this, but usually in conjunction
- * XXX with a gross error which appears to have
- * XXX occurred between the time I told the
- * XXX ESP to arbitrate and when I got the
- * XXX interrupt. Could I have misloaded the
- * XXX command bytes into the fifo? Actually,
- * XXX I most likely missed a phase, and therefore
- * XXX went into never never land and didn't even
- * XXX know it. That was the old driver though.
- * XXX What is even more peculiar is that the ESP
- * XXX showed the proper function complete and
- * XXX bus service bits in the interrupt register.
- */
-
- case ESP_STEP_FINI4:
- case ESP_STEP_FINI5:
- case ESP_STEP_FINI6:
- case ESP_STEP_FINI7:
- /* Account for the identify message */
- if(SCptr->SCp.phase == in_slct_norm)
- cmd_bytes_sent -= 1;
- };
- esp_cmd(esp, eregs, ESP_CMD_NULL);
-
- /* Be careful, we could really get fucked during synchronous
- * data transfers if we try to flush the fifo now.
- */
- if(!fcnt && /* Fifo is empty and... */
- /* either we are not doing synchronous transfers or... */
- (!esp_dev->sync_max_offset ||
- /* We are not going into data in phase. */
- ((esp->sreg & ESP_STAT_PMASK) != ESP_DIP)))
- esp_cmd(esp, eregs, ESP_CMD_FLUSH); /* flush is safe */
-
- /* See how far we got if this is not a slow command. */
- if(!esp->esp_slowcmd) {
- if(cmd_bytes_sent < 0)
- cmd_bytes_sent = 0;
- if(cmd_bytes_sent != SCptr->cmd_len) {
- /* Crapola, mark it as a slowcmd
- * so that we have some chance of
- * keeping the command alive with
- * good luck.
- *
- * XXX Actually, if we didn't send it all
- * XXX this means either we didn't set things
- * XXX up properly (driver bug) or the target
- * XXX or the ESP detected parity on one of
- * XXX the command bytes. This makes much
- * XXX more sense, and therefore this code
- * XXX should be changed to send out a
- * XXX parity error message or if the status
- * XXX register shows no parity error then
- * XXX just expect the target to bring the
- * XXX bus into message in phase so that it
- * XXX can send us the parity error message.
- * XXX SCSI sucks...
- */
- esp->esp_slowcmd = 1;
- esp->esp_scmdp = &(SCptr->cmnd[cmd_bytes_sent]);
- esp->esp_scmdleft = (SCptr->cmd_len - cmd_bytes_sent);
- }
- }
-
- /* Now figure out where we went. */
- esp_advance_phase(SCptr, in_the_dark);
- return esp_do_phase_determine(esp, eregs);
- }
-
- /* Did the target even make it? */
- if(esp->ireg == ESP_INTR_DC) {
- /* wheee... nobody there or they didn't like
- * what we told it to do, clean up.
- */
-
- /* If anyone is off the bus, but working on
- * a command in the background for us, tell
- * the ESP to listen for them.
- */
- if(esp->disconnected_SC)
- esp_cmd(esp, eregs, ESP_CMD_ESEL);
-
- if(((1<<SCptr->device->id) & esp->targets_present) &&
- esp->seqreg && esp->cur_msgout[0] == EXTENDED_MESSAGE &&
- (SCptr->SCp.phase == in_slct_msg ||
- SCptr->SCp.phase == in_slct_stop)) {
- /* shit */
- esp->snip = 0;
- ESPLOG(("esp%d: Failed synchronous negotiation for target %d "
- "lun %d\n", esp->esp_id, SCptr->device->id, SCptr->device->lun));
- esp_dev->sync_max_offset = 0;
- esp_dev->sync_min_period = 0;
- esp_dev->sync = 1; /* so we don't negotiate again */
-
- /* Run the command again, this time though we
- * won't try to negotiate for synchronous transfers.
- *
- * XXX I'd like to do something like send an
- * XXX INITIATOR_ERROR or ABORT message to the
- * XXX target to tell it, "Sorry I confused you,
- * XXX please come back and I will be nicer next
- * XXX time". But that requires having the target
- * XXX on the bus, and it has dropped BSY on us.
- */
- esp->current_SC = NULL;
- esp_advance_phase(SCptr, not_issued);
- prepend_SC(&esp->issue_SC, SCptr);
- esp_exec_cmd(esp);
- return do_intr_end;
- }
-
- /* Ok, this is normal, this is what we see during boot
- * or whenever when we are scanning the bus for targets.
- * But first make sure that is really what is happening.
- */
- if(((1<<SCptr->device->id) & esp->targets_present)) {
- ESPLOG(("esp%d: Warning, live target %d not responding to "
- "selection.\n", esp->esp_id, SCptr->device->id));
-
- /* This _CAN_ happen. The SCSI standard states that
- * the target is to _not_ respond to selection if
- * _it_ detects bad parity on the bus for any reason.
- * Therefore, we assume that if we've talked successfully
- * to this target before, bad parity is the problem.
- */
- esp_done(esp, (DID_PARITY << 16));
- } else {
- /* Else, there really isn't anyone there. */
- ESPMISC(("esp: selection failure, maybe nobody there?\n"));
- ESPMISC(("esp: target %d lun %d\n",
- SCptr->device->id, SCptr->device->lun));
- esp_done(esp, (DID_BAD_TARGET << 16));
- }
- return do_intr_end;
- }
-
-
- ESPLOG(("esp%d: Selection failure.\n", esp->esp_id));
- printk("esp%d: Currently -- ", esp->esp_id);
- esp_print_ireg(esp->ireg);
- printk(" ");
- esp_print_statreg(esp->sreg);
- printk(" ");
- esp_print_seqreg(esp->seqreg);
- printk("\n");
- printk("esp%d: New -- ", esp->esp_id);
- esp->sreg = esp_read(eregs->esp_status);
- esp->seqreg = esp_read(eregs->esp_sstep);
- esp->ireg = esp_read(eregs->esp_intrpt);
- esp_print_ireg(esp->ireg);
- printk(" ");
- esp_print_statreg(esp->sreg);
- printk(" ");
- esp_print_seqreg(esp->seqreg);
- printk("\n");
- ESPLOG(("esp%d: resetting bus\n", esp->esp_id));
- return do_reset_bus; /* ugh... */
-}
-
-/* Continue reading bytes for msgin phase. */
-static int esp_do_msgincont(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- if(esp->ireg & ESP_INTR_BSERV) {
- /* in the right phase too? */
- if((esp->sreg & ESP_STAT_PMASK) == ESP_MIP) {
- /* phew... */
- esp_cmd(esp, eregs, ESP_CMD_TI);
- esp_advance_phase(esp->current_SC, in_msgindone);
- return do_intr_end;
- }
-
- /* We changed phase but ESP shows bus service,
- * in this case it is most likely that we, the
- * hacker who has been up for 20hrs straight
- * staring at the screen, drowned in coffee
- * smelling like retched cigarette ashes
- * have miscoded something..... so, try to
- * recover as best we can.
- */
- ESPLOG(("esp%d: message in mis-carriage.\n", esp->esp_id));
- }
- esp_advance_phase(esp->current_SC, in_the_dark);
- return do_phase_determine;
-}
-
-static int check_singlebyte_msg(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- esp->prevmsgin = esp->cur_msgin[0];
- if(esp->cur_msgin[0] & 0x80) {
- /* wheee... */
- ESPLOG(("esp%d: target sends identify amidst phases\n",
- esp->esp_id));
- esp_advance_phase(esp->current_SC, in_the_dark);
- return 0;
- } else if(((esp->cur_msgin[0] & 0xf0) == 0x20) ||
- (esp->cur_msgin[0] == EXTENDED_MESSAGE)) {
- esp->msgin_len = 2;
- esp_advance_phase(esp->current_SC, in_msgincont);
- return 0;
- }
- esp_advance_phase(esp->current_SC, in_the_dark);
- switch(esp->cur_msgin[0]) {
- default:
- /* We don't want to hear about it. */
- ESPLOG(("esp%d: msg %02x which we don't know about\n", esp->esp_id,
- esp->cur_msgin[0]));
- return MESSAGE_REJECT;
-
- case NOP:
- ESPLOG(("esp%d: target %d sends a nop\n", esp->esp_id,
- esp->current_SC->device->id));
- return 0;
-
- case RESTORE_POINTERS:
- /* In this case we might also have to backup the
- * "slow command" pointer. It is rare to get such
- * a save/restore pointer sequence so early in the
- * bus transition sequences, but cover it.
- */
- if(esp->esp_slowcmd) {
- esp->esp_scmdleft = esp->current_SC->cmd_len;
- esp->esp_scmdp = &esp->current_SC->cmnd[0];
- }
- esp_restore_pointers(esp, esp->current_SC);
- return 0;
-
- case SAVE_POINTERS:
- esp_save_pointers(esp, esp->current_SC);
- return 0;
-
- case COMMAND_COMPLETE:
- case DISCONNECT:
- /* Freeing the bus, let it go. */
- esp->current_SC->SCp.phase = in_freeing;
- return 0;
-
- case MESSAGE_REJECT:
- ESPMISC(("msg reject, "));
- if(esp->prevmsgout == EXTENDED_MESSAGE) {
- struct esp_device *esp_dev = esp->current_SC->device->hostdata;
-
- /* Doesn't look like this target can
- * do synchronous or WIDE transfers.
- */
- ESPSDTR(("got reject, was trying nego, clearing sync/WIDE\n"));
- esp_dev->sync = 1;
- esp_dev->wide = 1;
- esp_dev->sync_min_period = 0;
- esp_dev->sync_max_offset = 0;
- return 0;
- } else {
- ESPMISC(("not sync nego, sending ABORT\n"));
- return ABORT;
- }
- };
-}
-
-/* Target negotiates for synchronous transfers before we do, this
- * is legal although very strange. What is even funnier is that
- * the SCSI2 standard specifically recommends against targets doing
- * this because so many initiators cannot cope with this occurring.
- */
-static int target_with_ants_in_pants(struct NCR_ESP *esp,
- Scsi_Cmnd *SCptr,
- struct esp_device *esp_dev)
-{
- if(esp_dev->sync || SCptr->device->borken) {
- /* sorry, no can do */
- ESPSDTR(("forcing to async, "));
- build_sync_nego_msg(esp, 0, 0);
- esp_dev->sync = 1;
- esp->snip = 1;
- ESPLOG(("esp%d: hoping for msgout\n", esp->esp_id));
- esp_advance_phase(SCptr, in_the_dark);
- return EXTENDED_MESSAGE;
- }
-
- /* Ok, we'll check them out... */
- return 0;
-}
-
-static void sync_report(struct NCR_ESP *esp)
-{
- int msg3, msg4;
- char *type;
-
- msg3 = esp->cur_msgin[3];
- msg4 = esp->cur_msgin[4];
- if(msg4) {
- int hz = 1000000000 / (msg3 * 4);
- int integer = hz / 1000000;
- int fraction = (hz - (integer * 1000000)) / 10000;
- if((msg3 * 4) < 200) {
- type = "FAST";
- } else {
- type = "synchronous";
- }
-
- /* Do not transform this back into one big printk
- * again, it triggers a bug in our sparc64-gcc272
- * sibling call optimization. -DaveM
- */
- ESPLOG((KERN_INFO "esp%d: target %d ",
- esp->esp_id, esp->current_SC->device->id));
- ESPLOG(("[period %dns offset %d %d.%02dMHz ",
- (int) msg3 * 4, (int) msg4,
- integer, fraction));
- ESPLOG(("%s SCSI%s]\n", type,
- (((msg3 * 4) < 200) ? "-II" : "")));
- } else {
- ESPLOG((KERN_INFO "esp%d: target %d asynchronous\n",
- esp->esp_id, esp->current_SC->device->id));
- }
-}
-
-static int check_multibyte_msg(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- struct esp_device *esp_dev = SCptr->device->hostdata;
- unchar regval = 0;
- int message_out = 0;
-
- ESPSDTR(("chk multibyte msg: "));
- if(esp->cur_msgin[2] == EXTENDED_SDTR) {
- int period = esp->cur_msgin[3];
- int offset = esp->cur_msgin[4];
-
- ESPSDTR(("is sync nego response, "));
- if(!esp->snip) {
- int rval;
-
- /* Target negotiates first! */
- ESPSDTR(("target jumps the gun, "));
- message_out = EXTENDED_MESSAGE; /* we must respond */
- rval = target_with_ants_in_pants(esp, SCptr, esp_dev);
- if(rval)
- return rval;
- }
-
- ESPSDTR(("examining sdtr, "));
-
- /* Offset cannot be larger than ESP fifo size. */
- if(offset > 15) {
- ESPSDTR(("offset too big %2x, ", offset));
- offset = 15;
- ESPSDTR(("sending back new offset\n"));
- build_sync_nego_msg(esp, period, offset);
- return EXTENDED_MESSAGE;
- }
-
- if(offset && period > esp->max_period) {
- /* Yeee, async for this slow device. */
- ESPSDTR(("period too long %2x, ", period));
- build_sync_nego_msg(esp, 0, 0);
- ESPSDTR(("hoping for msgout\n"));
- esp_advance_phase(esp->current_SC, in_the_dark);
- return EXTENDED_MESSAGE;
- } else if (offset && period < esp->min_period) {
- ESPSDTR(("period too short %2x, ", period));
- period = esp->min_period;
- if(esp->erev > esp236)
- regval = 4;
- else
- regval = 5;
- } else if(offset) {
- int tmp;
-
- ESPSDTR(("period is ok, "));
- tmp = esp->ccycle / 1000;
- regval = (((period << 2) + tmp - 1) / tmp);
- if(regval && (esp->erev > esp236)) {
- if(period >= 50)
- regval--;
- }
- }
-
- if(offset) {
- unchar bit;
-
- esp_dev->sync_min_period = (regval & 0x1f);
- esp_dev->sync_max_offset = (offset | esp->radelay);
- if(esp->erev > esp236) {
- if(esp->erev == fas100a)
- bit = ESP_CONFIG3_FAST;
- else
- bit = ESP_CONFIG3_FSCSI;
- if(period < 50)
- esp->config3[SCptr->device->id] |= bit;
- else
- esp->config3[SCptr->device->id] &= ~bit;
- esp->prev_cfg3 = esp->config3[SCptr->device->id];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- }
- esp->prev_soff = esp_dev->sync_min_period;
- esp_write(eregs->esp_soff, esp->prev_soff);
- esp->prev_stp = esp_dev->sync_max_offset;
- esp_write(eregs->esp_stp, esp->prev_stp);
-
- ESPSDTR(("soff=%2x stp=%2x cfg3=%2x\n",
- esp_dev->sync_max_offset,
- esp_dev->sync_min_period,
- esp->config3[scmd_id(SCptr)]));
-
- esp->snip = 0;
- } else if(esp_dev->sync_max_offset) {
- unchar bit;
-
- /* back to async mode */
- ESPSDTR(("unaccaptable sync nego, forcing async\n"));
- esp_dev->sync_max_offset = 0;
- esp_dev->sync_min_period = 0;
- esp->prev_soff = 0;
- esp_write(eregs->esp_soff, 0);
- esp->prev_stp = 0;
- esp_write(eregs->esp_stp, 0);
- if(esp->erev > esp236) {
- if(esp->erev == fas100a)
- bit = ESP_CONFIG3_FAST;
- else
- bit = ESP_CONFIG3_FSCSI;
- esp->config3[SCptr->device->id] &= ~bit;
- esp->prev_cfg3 = esp->config3[SCptr->device->id];
- esp_write(eregs->esp_cfg3, esp->prev_cfg3);
- }
- }
-
- sync_report(esp);
-
- ESPSDTR(("chk multibyte msg: sync is known, "));
- esp_dev->sync = 1;
-
- if(message_out) {
- ESPLOG(("esp%d: sending sdtr back, hoping for msgout\n",
- esp->esp_id));
- build_sync_nego_msg(esp, period, offset);
- esp_advance_phase(SCptr, in_the_dark);
- return EXTENDED_MESSAGE;
- }
-
- ESPSDTR(("returning zero\n"));
- esp_advance_phase(SCptr, in_the_dark); /* ...or else! */
- return 0;
- } else if(esp->cur_msgin[2] == EXTENDED_WDTR) {
- ESPLOG(("esp%d: AIEEE wide msg received\n", esp->esp_id));
- message_out = MESSAGE_REJECT;
- } else if(esp->cur_msgin[2] == EXTENDED_MODIFY_DATA_POINTER) {
- ESPLOG(("esp%d: rejecting modify data ptr msg\n", esp->esp_id));
- message_out = MESSAGE_REJECT;
- }
- esp_advance_phase(SCptr, in_the_dark);
- return message_out;
-}
-
-static int esp_do_msgindone(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- int message_out = 0, it = 0, rval;
-
- rval = skipahead1(esp, eregs, SCptr, in_msgin, in_msgindone);
- if(rval)
- return rval;
- if(SCptr->SCp.sent_command != in_status) {
- if(!(esp->ireg & ESP_INTR_DC)) {
- if(esp->msgin_len && (esp->sreg & ESP_STAT_PERR)) {
- message_out = MSG_PARITY_ERROR;
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- } else if((it = (esp_read(eregs->esp_fflags) & ESP_FF_FBYTES))!=1) {
- /* We certainly dropped the ball somewhere. */
- message_out = INITIATOR_ERROR;
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- } else if(!esp->msgin_len) {
- it = esp_read(eregs->esp_fdata);
- esp_advance_phase(SCptr, in_msgincont);
- } else {
- /* it is ok and we want it */
- it = esp->cur_msgin[esp->msgin_ctr] =
- esp_read(eregs->esp_fdata);
- esp->msgin_ctr++;
- }
- } else {
- esp_advance_phase(SCptr, in_the_dark);
- return do_work_bus;
- }
- } else {
- it = esp->cur_msgin[0];
- }
- if(!message_out && esp->msgin_len) {
- if(esp->msgin_ctr < esp->msgin_len) {
- esp_advance_phase(SCptr, in_msgincont);
- } else if(esp->msgin_len == 1) {
- message_out = check_singlebyte_msg(esp, eregs);
- } else if(esp->msgin_len == 2) {
- if(esp->cur_msgin[0] == EXTENDED_MESSAGE) {
- if((it+2) >= 15) {
- message_out = MESSAGE_REJECT;
- } else {
- esp->msgin_len = (it + 2);
- esp_advance_phase(SCptr, in_msgincont);
- }
- } else {
- message_out = MESSAGE_REJECT; /* foo on you */
- }
- } else {
- message_out = check_multibyte_msg(esp, eregs);
- }
- }
- if(message_out < 0) {
- return -message_out;
- } else if(message_out) {
- if(((message_out != 1) &&
- ((message_out < 0x20) || (message_out & 0x80))))
- esp->msgout_len = 1;
- esp->cur_msgout[0] = message_out;
- esp_cmd(esp, eregs, ESP_CMD_SATN);
- esp_advance_phase(SCptr, in_the_dark);
- esp->msgin_len = 0;
- }
- esp->sreg = esp_read(eregs->esp_status);
- esp->sreg &= ~(ESP_STAT_INTR);
- if((esp->sreg & (ESP_STAT_PMSG|ESP_STAT_PCD)) == (ESP_STAT_PMSG|ESP_STAT_PCD))
- esp_cmd(esp, eregs, ESP_CMD_MOK);
- if((SCptr->SCp.sent_command == in_msgindone) &&
- (SCptr->SCp.phase == in_freeing))
- return esp_do_freebus(esp, eregs);
- return do_intr_end;
-}
-
-static int esp_do_cmdbegin(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- unsigned char tmp;
- Scsi_Cmnd *SCptr = esp->current_SC;
-
- esp_advance_phase(SCptr, in_cmdend);
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- tmp = *esp->esp_scmdp++;
- esp->esp_scmdleft--;
- esp_write(eregs->esp_fdata, tmp);
- esp_cmd(esp, eregs, ESP_CMD_TI);
- return do_intr_end;
-}
-
-static int esp_do_cmddone(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- esp_cmd(esp, eregs, ESP_CMD_NULL);
- if(esp->ireg & ESP_INTR_BSERV) {
- esp_advance_phase(esp->current_SC, in_the_dark);
- return esp_do_phase_determine(esp, eregs);
- }
- ESPLOG(("esp%d: in do_cmddone() but didn't get BSERV interrupt.\n",
- esp->esp_id));
- return do_reset_bus;
-}
-
-static int esp_do_msgout(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- switch(esp->msgout_len) {
- case 1:
- esp_write(eregs->esp_fdata, esp->cur_msgout[0]);
- esp_cmd(esp, eregs, ESP_CMD_TI);
- break;
-
- case 2:
- if(esp->do_pio_cmds){
- esp_write(eregs->esp_fdata, esp->cur_msgout[0]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[1]);
- esp_cmd(esp, eregs, ESP_CMD_TI);
- } else {
- esp->esp_command[0] = esp->cur_msgout[0];
- esp->esp_command[1] = esp->cur_msgout[1];
- esp->dma_setup(esp, esp->esp_command_dvma, 2, 0);
- esp_setcount(eregs, 2);
- esp_cmd(esp, eregs, ESP_CMD_DMA | ESP_CMD_TI);
- }
- break;
-
- case 4:
- esp->snip = 1;
- if(esp->do_pio_cmds){
- esp_write(eregs->esp_fdata, esp->cur_msgout[0]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[1]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[2]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[3]);
- esp_cmd(esp, eregs, ESP_CMD_TI);
- } else {
- esp->esp_command[0] = esp->cur_msgout[0];
- esp->esp_command[1] = esp->cur_msgout[1];
- esp->esp_command[2] = esp->cur_msgout[2];
- esp->esp_command[3] = esp->cur_msgout[3];
- esp->dma_setup(esp, esp->esp_command_dvma, 4, 0);
- esp_setcount(eregs, 4);
- esp_cmd(esp, eregs, ESP_CMD_DMA | ESP_CMD_TI);
- }
- break;
-
- case 5:
- esp->snip = 1;
- if(esp->do_pio_cmds){
- esp_write(eregs->esp_fdata, esp->cur_msgout[0]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[1]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[2]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[3]);
- esp_write(eregs->esp_fdata, esp->cur_msgout[4]);
- esp_cmd(esp, eregs, ESP_CMD_TI);
- } else {
- esp->esp_command[0] = esp->cur_msgout[0];
- esp->esp_command[1] = esp->cur_msgout[1];
- esp->esp_command[2] = esp->cur_msgout[2];
- esp->esp_command[3] = esp->cur_msgout[3];
- esp->esp_command[4] = esp->cur_msgout[4];
- esp->dma_setup(esp, esp->esp_command_dvma, 5, 0);
- esp_setcount(eregs, 5);
- esp_cmd(esp, eregs, ESP_CMD_DMA | ESP_CMD_TI);
- }
- break;
-
- default:
- /* whoops */
- ESPMISC(("bogus msgout sending NOP\n"));
- esp->cur_msgout[0] = NOP;
- esp_write(eregs->esp_fdata, esp->cur_msgout[0]);
- esp->msgout_len = 1;
- esp_cmd(esp, eregs, ESP_CMD_TI);
- break;
- }
- esp_advance_phase(esp->current_SC, in_msgoutdone);
- return do_intr_end;
-}
-
-static int esp_do_msgoutdone(struct NCR_ESP *esp,
- struct ESP_regs *eregs)
-{
- if((esp->msgout_len > 1) && esp->dma_barrier)
- esp->dma_barrier(esp);
-
- if(!(esp->ireg & ESP_INTR_DC)) {
- esp_cmd(esp, eregs, ESP_CMD_NULL);
- switch(esp->sreg & ESP_STAT_PMASK) {
- case ESP_MOP:
- /* whoops, parity error */
- ESPLOG(("esp%d: still in msgout, parity error assumed\n",
- esp->esp_id));
- if(esp->msgout_len > 1)
- esp_cmd(esp, eregs, ESP_CMD_SATN);
- esp_advance_phase(esp->current_SC, in_msgout);
- return do_work_bus;
-
- case ESP_DIP:
- break;
-
- default:
- if(!fcount(esp, eregs) &&
- !(((struct esp_device *)esp->current_SC->device->hostdata)->sync_max_offset))
- esp_cmd(esp, eregs, ESP_CMD_FLUSH);
- break;
-
- };
- }
-
- /* If we sent out a synchronous negotiation message, update
- * our state.
- */
- if(esp->cur_msgout[2] == EXTENDED_MESSAGE &&
- esp->cur_msgout[4] == EXTENDED_SDTR) {
- esp->snip = 1; /* anal retentiveness... */
- }
-
- esp->prevmsgout = esp->cur_msgout[0];
- esp->msgout_len = 0;
- esp_advance_phase(esp->current_SC, in_the_dark);
- return esp_do_phase_determine(esp, eregs);
-}
-
-static int esp_bus_unexpected(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- ESPLOG(("esp%d: command in weird state %2x\n",
- esp->esp_id, esp->current_SC->SCp.phase));
- return do_reset_bus;
-}
-
-static espfunc_t bus_vector[] = {
- esp_do_data_finale,
- esp_do_data_finale,
- esp_bus_unexpected,
- esp_do_msgin,
- esp_do_msgincont,
- esp_do_msgindone,
- esp_do_msgout,
- esp_do_msgoutdone,
- esp_do_cmdbegin,
- esp_do_cmddone,
- esp_do_status,
- esp_do_freebus,
- esp_do_phase_determine,
- esp_bus_unexpected,
- esp_bus_unexpected,
- esp_bus_unexpected,
-};
-
-/* This is the second tier in our dual-level SCSI state machine. */
-static int esp_work_bus(struct NCR_ESP *esp, struct ESP_regs *eregs)
-{
- Scsi_Cmnd *SCptr = esp->current_SC;
- unsigned int phase;
-
- ESPBUS(("esp_work_bus: "));
- if(!SCptr) {
- ESPBUS(("reconnect\n"));
- return esp_do_reconnect(esp, eregs);
- }
- phase = SCptr->SCp.phase;
- if ((phase & 0xf0) == in_phases_mask)
- return bus_vector[(phase & 0x0f)](esp, eregs);
- else if((phase & 0xf0) == in_slct_mask)
- return esp_select_complete(esp, eregs);
- else
- return esp_bus_unexpected(esp, eregs);
-}
-
-static espfunc_t isvc_vector[] = {
- NULL,
- esp_do_phase_determine,
- esp_do_resetbus,
- esp_finish_reset,
- esp_work_bus
-};
-
-/* Main interrupt handler for an esp adapter. */
-void esp_handle(struct NCR_ESP *esp)
-{
- struct ESP_regs *eregs;
- Scsi_Cmnd *SCptr;
- int what_next = do_intr_end;
- eregs = esp->eregs;
- SCptr = esp->current_SC;
-
- if(esp->dma_irq_entry)
- esp->dma_irq_entry(esp);
-
- /* Check for errors. */
- esp->sreg = esp_read(eregs->esp_status);
- esp->sreg &= (~ESP_STAT_INTR);
- esp->seqreg = (esp_read(eregs->esp_sstep) & ESP_STEP_VBITS);
- esp->ireg = esp_read(eregs->esp_intrpt); /* Unlatch intr and stat regs */
- ESPIRQ(("handle_irq: [sreg<%02x> sstep<%02x> ireg<%02x>]\n",
- esp->sreg, esp->seqreg, esp->ireg));
- if(esp->sreg & (ESP_STAT_SPAM)) {
- /* Gross error, could be due to one of:
- *
- * - top of fifo overwritten, could be because
- * we tried to do a synchronous transfer with
- * an offset greater than ESP fifo size
- *
- * - top of command register overwritten
- *
- * - DMA setup to go in one direction, SCSI
- * bus points in the other, whoops
- *
- * - weird phase change during asynchronous
- * data phase while we are initiator
- */
- ESPLOG(("esp%d: Gross error sreg=%2x\n", esp->esp_id, esp->sreg));
-
- /* If a command is live on the bus we cannot safely
- * reset the bus, so we'll just let the pieces fall
- * where they may. Here we are hoping that the
- * target will be able to cleanly go away soon
- * so we can safely reset things.
- */
- if(!SCptr) {
- ESPLOG(("esp%d: No current cmd during gross error, "
- "resetting bus\n", esp->esp_id));
- what_next = do_reset_bus;
- goto state_machine;
- }
- }
-
- /* No current cmd is only valid at this point when there are
- * commands off the bus or we are trying a reset.
- */
- if(!SCptr && !esp->disconnected_SC && !(esp->ireg & ESP_INTR_SR)) {
- /* Panic is safe, since current_SC is null. */
- ESPLOG(("esp%d: no command in esp_handle()\n", esp->esp_id));
- panic("esp_handle: current_SC == penguin within interrupt!");
- }
-
- if(esp->ireg & (ESP_INTR_IC)) {
- /* Illegal command fed to ESP. Outside of obvious
- * software bugs that could cause this, there is
- * a condition with ESP100 where we can confuse the
- * ESP into an erroneous illegal command interrupt
- * because it does not scrape the FIFO properly
- * for reselection. See esp100_reconnect_hwbug()
- * to see how we try very hard to avoid this.
- */
- ESPLOG(("esp%d: invalid command\n", esp->esp_id));
-
- esp_dump_state(esp, eregs);
-
- if(SCptr) {
- /* Devices with very buggy firmware can drop BSY
- * during a scatter list interrupt when using sync
- * mode transfers. We continue the transfer as
- * expected, the target drops the bus, the ESP
- * gets confused, and we get a illegal command
- * interrupt because the bus is in the disconnected
- * state now and ESP_CMD_TI is only allowed when
- * a nexus is alive on the bus.
- */
- ESPLOG(("esp%d: Forcing async and disabling disconnect for "
- "target %d\n", esp->esp_id, SCptr->device->id));
- SCptr->device->borken = 1; /* foo on you */
- }
-
- what_next = do_reset_bus;
- } else if(!(esp->ireg & ~(ESP_INTR_FDONE | ESP_INTR_BSERV | ESP_INTR_DC))) {
- int phase;
-
- if(SCptr) {
- phase = SCptr->SCp.phase;
- if(phase & in_phases_mask) {
- what_next = esp_work_bus(esp, eregs);
- } else if(phase & in_slct_mask) {
- what_next = esp_select_complete(esp, eregs);
- } else {
- ESPLOG(("esp%d: interrupt for no good reason...\n",
- esp->esp_id));
- what_next = do_intr_end;
- }
- } else {
- ESPLOG(("esp%d: BSERV or FDONE or DC while SCptr==NULL\n",
- esp->esp_id));
- what_next = do_reset_bus;
- }
- } else if(esp->ireg & ESP_INTR_SR) {
- ESPLOG(("esp%d: SCSI bus reset interrupt\n", esp->esp_id));
- what_next = do_reset_complete;
- } else if(esp->ireg & (ESP_INTR_S | ESP_INTR_SATN)) {
- ESPLOG(("esp%d: AIEEE we have been selected by another initiator!\n",
- esp->esp_id));
- what_next = do_reset_bus;
- } else if(esp->ireg & ESP_INTR_RSEL) {
- if(!SCptr) {
- /* This is ok. */
- what_next = esp_do_reconnect(esp, eregs);
- } else if(SCptr->SCp.phase & in_slct_mask) {
- /* Only selection code knows how to clean
- * up properly.
- */
- ESPDISC(("Reselected during selection attempt\n"));
- what_next = esp_select_complete(esp, eregs);
- } else {
- ESPLOG(("esp%d: Reselected while bus is busy\n",
- esp->esp_id));
- what_next = do_reset_bus;
- }
- }
-
- /* This is tier-one in our dual level SCSI state machine. */
-state_machine:
- while(what_next != do_intr_end) {
- if (what_next >= do_phase_determine &&
- what_next < do_intr_end)
- what_next = isvc_vector[what_next](esp, eregs);
- else {
- /* state is completely lost ;-( */
- ESPLOG(("esp%d: interrupt engine loses state, resetting bus\n",
- esp->esp_id));
- what_next = do_reset_bus;
- }
- }
- if(esp->dma_irq_exit)
- esp->dma_irq_exit(esp);
-}
-EXPORT_SYMBOL(esp_handle);
-
-#ifndef CONFIG_SMP
-irqreturn_t esp_intr(int irq, void *dev_id)
-{
- struct NCR_ESP *esp;
- unsigned long flags;
- int again;
- struct Scsi_Host *dev = dev_id;
-
- /* Handle all ESP interrupts showing at this IRQ level. */
- spin_lock_irqsave(dev->host_lock, flags);
-repeat:
- again = 0;
- for_each_esp(esp) {
-#ifndef __mips__
- if(((esp)->irq & 0xff) == irq) {
-#endif
- if(esp->dma_irq_p(esp)) {
- again = 1;
-
- esp->dma_ints_off(esp);
-
- ESPIRQ(("I%d(", esp->esp_id));
- esp_handle(esp);
- ESPIRQ((")"));
-
- esp->dma_ints_on(esp);
- }
-#ifndef __mips__
- }
-#endif
- }
- if(again)
- goto repeat;
- spin_unlock_irqrestore(dev->host_lock, flags);
- return IRQ_HANDLED;
-}
-#else
-/* For SMP we only service one ESP on the list list at our IRQ level! */
-irqreturn_t esp_intr(int irq, void *dev_id)
-{
- struct NCR_ESP *esp;
- unsigned long flags;
- struct Scsi_Host *dev = dev_id;
-
- /* Handle all ESP interrupts showing at this IRQ level. */
- spin_lock_irqsave(dev->host_lock, flags);
- for_each_esp(esp) {
- if(((esp)->irq & 0xf) == irq) {
- if(esp->dma_irq_p(esp)) {
- esp->dma_ints_off(esp);
-
- ESPIRQ(("I[%d:%d](",
- smp_processor_id(), esp->esp_id));
- esp_handle(esp);
- ESPIRQ((")"));
-
- esp->dma_ints_on(esp);
- goto out;
- }
- }
- }
-out:
- spin_unlock_irqrestore(dev->host_lock, flags);
- return IRQ_HANDLED;
-}
-#endif
-
-int esp_slave_alloc(struct scsi_device *SDptr)
-{
- struct esp_device *esp_dev =
- kzalloc(sizeof(struct esp_device), GFP_ATOMIC);
-
- if (!esp_dev)
- return -ENOMEM;
- SDptr->hostdata = esp_dev;
- return 0;
-}
-
-void esp_slave_destroy(struct scsi_device *SDptr)
-{
- struct NCR_ESP *esp = (struct NCR_ESP *) SDptr->host->hostdata;
-
- esp->targets_present &= ~(1 << sdev_id(SDptr));
- kfree(SDptr->hostdata);
- SDptr->hostdata = NULL;
-}
-
-#ifdef MODULE
-int init_module(void) { return 0; }
-void cleanup_module(void) {}
-void esp_release(void)
-{
- esps_in_use--;
- esps_running = esps_in_use;
-}
-EXPORT_SYMBOL(esp_release);
-#endif
-
-EXPORT_SYMBOL(esp_abort);
-EXPORT_SYMBOL(esp_allocate);
-EXPORT_SYMBOL(esp_deallocate);
-EXPORT_SYMBOL(esp_initialize);
-EXPORT_SYMBOL(esp_intr);
-EXPORT_SYMBOL(esp_queue);
-EXPORT_SYMBOL(esp_reset);
-EXPORT_SYMBOL(esp_slave_alloc);
-EXPORT_SYMBOL(esp_slave_destroy);
-EXPORT_SYMBOL(esps_in_use);
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/NCR53C9x.h b/drivers/scsi/NCR53C9x.h
deleted file mode 100644
index d85cb73..0000000
--- a/drivers/scsi/NCR53C9x.h
+++ /dev/null
@@ -1,668 +0,0 @@
-/* NCR53C9x.c: Defines and structures for the NCR53C9x generic driver.
- *
- * Originaly esp.h: Defines and structures for the Sparc ESP
- * (Enhanced SCSI Processor) driver under Linux.
- *
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- *
- * Generalization by Jesper Skov (jskov@cygnus.co.uk)
- *
- * More generalization (for i386 stuff) by Tymm Twillman (tymm@computer.org)
- */
-
-#ifndef NCR53C9X_H
-#define NCR53C9X_H
-
-#include <linux/interrupt.h>
-
-/* djweis for mac driver */
-#if defined(CONFIG_MAC)
-#define PAD_SIZE 15
-#else
-#define PAD_SIZE 3
-#endif
-
-/* Handle multiple hostadapters on Amiga
- * generally PAD_SIZE = 3
- * but there is one exception: Oktagon (PAD_SIZE = 1) */
-#if defined(CONFIG_OKTAGON_SCSI) || defined(CONFIG_OKTAGON_SCSI_MODULE)
-#undef PAD_SIZE
-#if defined(CONFIG_BLZ1230_SCSI) || defined(CONFIG_BLZ1230_SCSI_MODULE) || \
- defined(CONFIG_BLZ2060_SCSI) || defined(CONFIG_BLZ2060_SCSI_MODULE) || \
- defined(CONFIG_CYBERSTORM_SCSI) || defined(CONFIG_CYBERSTORM_SCSI_MODULE) || \
- defined(CONFIG_CYBERSTORMII_SCSI) || defined(CONFIG_CYBERSTORMII_SCSI_MODULE) || \
- defined(CONFIG_FASTLANE_SCSI) || defined(CONFIG_FASTLANE_SCSI_MODULE)
-#define MULTIPLE_PAD_SIZES
-#else
-#define PAD_SIZE 1
-#endif
-#endif
-
-/* Macros for debugging messages */
-
-#define DEBUG_ESP
-/* #define DEBUG_ESP_DATA */
-/* #define DEBUG_ESP_QUEUE */
-/* #define DEBUG_ESP_DISCONNECT */
-/* #define DEBUG_ESP_STATUS */
-/* #define DEBUG_ESP_PHASES */
-/* #define DEBUG_ESP_WORKBUS */
-/* #define DEBUG_STATE_MACHINE */
-/* #define DEBUG_ESP_CMDS */
-/* #define DEBUG_ESP_IRQS */
-/* #define DEBUG_SDTR */
-/* #define DEBUG_ESP_SG */
-
-/* Use the following to sprinkle debugging messages in a way which
- * suits you if combinations of the above become too verbose when
- * trying to track down a specific problem.
- */
-/* #define DEBUG_ESP_MISC */
-
-#if defined(DEBUG_ESP)
-#define ESPLOG(foo) printk foo
-#else
-#define ESPLOG(foo)
-#endif /* (DEBUG_ESP) */
-
-#if defined(DEBUG_ESP_DATA)
-#define ESPDATA(foo) printk foo
-#else
-#define ESPDATA(foo)
-#endif
-
-#if defined(DEBUG_ESP_QUEUE)
-#define ESPQUEUE(foo) printk foo
-#else
-#define ESPQUEUE(foo)
-#endif
-
-#if defined(DEBUG_ESP_DISCONNECT)
-#define ESPDISC(foo) printk foo
-#else
-#define ESPDISC(foo)
-#endif
-
-#if defined(DEBUG_ESP_STATUS)
-#define ESPSTAT(foo) printk foo
-#else
-#define ESPSTAT(foo)
-#endif
-
-#if defined(DEBUG_ESP_PHASES)
-#define ESPPHASE(foo) printk foo
-#else
-#define ESPPHASE(foo)
-#endif
-
-#if defined(DEBUG_ESP_WORKBUS)
-#define ESPBUS(foo) printk foo
-#else
-#define ESPBUS(foo)
-#endif
-
-#if defined(DEBUG_ESP_IRQS)
-#define ESPIRQ(foo) printk foo
-#else
-#define ESPIRQ(foo)
-#endif
-
-#if defined(DEBUG_SDTR)
-#define ESPSDTR(foo) printk foo
-#else
-#define ESPSDTR(foo)
-#endif
-
-#if defined(DEBUG_ESP_MISC)
-#define ESPMISC(foo) printk foo
-#else
-#define ESPMISC(foo)
-#endif
-
-/*
- * padding for register structure
- */
-#ifdef CONFIG_JAZZ_ESP
-#define EREGS_PAD(n)
-#else
-#ifndef MULTIPLE_PAD_SIZES
-#define EREGS_PAD(n) unchar n[PAD_SIZE];
-#endif
-#endif
-
-/* The ESP SCSI controllers have their register sets in three
- * "classes":
- *
- * 1) Registers which are both read and write.
- * 2) Registers which are read only.
- * 3) Registers which are write only.
- *
- * Yet, they all live within the same IO space.
- */
-
-#if !defined(__i386__) && !defined(__x86_64__)
-
-#ifndef MULTIPLE_PAD_SIZES
-
-#ifdef CONFIG_CPU_HAS_WB
-#include <asm/wbflush.h>
-#define esp_write(__reg, __val) do{(__reg) = (__val); wbflush();} while(0)
-#else
-#define esp_write(__reg, __val) ((__reg) = (__val))
-#endif
-#define esp_read(__reg) (__reg)
-
-struct ESP_regs {
- /* Access Description Offset */
- volatile unchar esp_tclow; /* rw Low bits of the transfer count 0x00 */
- EREGS_PAD(tlpad1);
- volatile unchar esp_tcmed; /* rw Mid bits of the transfer count 0x04 */
- EREGS_PAD(fdpad);
- volatile unchar esp_fdata; /* rw FIFO data bits 0x08 */
- EREGS_PAD(cbpad);
- volatile unchar esp_cmnd; /* rw SCSI command bits 0x0c */
- EREGS_PAD(stpad);
- volatile unchar esp_status; /* ro ESP status register 0x10 */
-#define esp_busid esp_status /* wo Bus ID for select/reselect 0x10 */
- EREGS_PAD(irqpd);
- volatile unchar esp_intrpt; /* ro Kind of interrupt 0x14 */
-#define esp_timeo esp_intrpt /* wo Timeout value for select/resel 0x14 */
- EREGS_PAD(sspad);
- volatile unchar esp_sstep; /* ro Sequence step register 0x18 */
-#define esp_stp esp_sstep /* wo Transfer period per sync 0x18 */
- EREGS_PAD(ffpad);
- volatile unchar esp_fflags; /* ro Bits of current FIFO info 0x1c */
-#define esp_soff esp_fflags /* wo Sync offset 0x1c */
- EREGS_PAD(cf1pd);
- volatile unchar esp_cfg1; /* rw First configuration register 0x20 */
- EREGS_PAD(cfpad);
- volatile unchar esp_cfact; /* wo Clock conversion factor 0x24 */
- EREGS_PAD(ctpad);
- volatile unchar esp_ctest; /* wo Chip test register 0x28 */
- EREGS_PAD(cf2pd);
- volatile unchar esp_cfg2; /* rw Second configuration register 0x2c */
- EREGS_PAD(cf3pd);
-
- /* The following is only found on the 53C9X series SCSI chips */
- volatile unchar esp_cfg3; /* rw Third configuration register 0x30 */
- EREGS_PAD(cf4pd);
- volatile unchar esp_cfg4; /* rw Fourth configuration register 0x34 */
- EREGS_PAD(thpd);
- /* The following is found on all chips except the NCR53C90 (ESP100) */
- volatile unchar esp_tchi; /* rw High bits of transfer count 0x38 */
-#define esp_uid esp_tchi /* ro Unique ID code 0x38 */
- EREGS_PAD(fgpad);
- volatile unchar esp_fgrnd; /* rw Data base for fifo 0x3c */
-};
-
-#else /* MULTIPLE_PAD_SIZES */
-
-#define esp_write(__reg, __val) (*(__reg) = (__val))
-#define esp_read(__reg) (*(__reg))
-
-struct ESP_regs {
- unsigned char io_addr[64]; /* dummy */
- /* Access Description Offset */
-#define esp_tclow io_addr /* rw Low bits of the transfer count 0x00 */
-#define esp_tcmed io_addr + (1<<(esp->shift)) /* rw Mid bits of the transfer count 0x04 */
-#define esp_fdata io_addr + (2<<(esp->shift)) /* rw FIFO data bits 0x08 */
-#define esp_cmnd io_addr + (3<<(esp->shift)) /* rw SCSI command bits 0x0c */
-#define esp_status io_addr + (4<<(esp->shift)) /* ro ESP status register 0x10 */
-#define esp_busid esp_status /* wo Bus ID for select/reselect 0x10 */
-#define esp_intrpt io_addr + (5<<(esp->shift)) /* ro Kind of interrupt 0x14 */
-#define esp_timeo esp_intrpt /* wo Timeout value for select/resel 0x14 */
-#define esp_sstep io_addr + (6<<(esp->shift)) /* ro Sequence step register 0x18 */
-#define esp_stp esp_sstep /* wo Transfer period per sync 0x18 */
-#define esp_fflags io_addr + (7<<(esp->shift)) /* ro Bits of current FIFO info 0x1c */
-#define esp_soff esp_fflags /* wo Sync offset 0x1c */
-#define esp_cfg1 io_addr + (8<<(esp->shift)) /* rw First configuration register 0x20 */
-#define esp_cfact io_addr + (9<<(esp->shift)) /* wo Clock conversion factor 0x24 */
-#define esp_ctest io_addr + (10<<(esp->shift)) /* wo Chip test register 0x28 */
-#define esp_cfg2 io_addr + (11<<(esp->shift)) /* rw Second configuration register 0x2c */
-
- /* The following is only found on the 53C9X series SCSI chips */
-#define esp_cfg3 io_addr + (12<<(esp->shift)) /* rw Third configuration register 0x30 */
-#define esp_cfg4 io_addr + (13<<(esp->shift)) /* rw Fourth configuration register 0x34 */
-
- /* The following is found on all chips except the NCR53C90 (ESP100) */
-#define esp_tchi io_addr + (14<<(esp->shift)) /* rw High bits of transfer count 0x38 */
-#define esp_uid esp_tchi /* ro Unique ID code 0x38 */
-#define esp_fgrnd io_addr + (15<<(esp->shift)) /* rw Data base for fifo 0x3c */
-};
-
-#endif
-
-#else /* !defined(__i386__) && !defined(__x86_64__) */
-
-#define esp_write(__reg, __val) outb((__val), (__reg))
-#define esp_read(__reg) inb((__reg))
-
-struct ESP_regs {
- unsigned int io_addr;
- /* Access Description Offset */
-#define esp_tclow io_addr /* rw Low bits of the transfer count 0x00 */
-#define esp_tcmed io_addr + 1 /* rw Mid bits of the transfer count 0x04 */
-#define esp_fdata io_addr + 2 /* rw FIFO data bits 0x08 */
-#define esp_cmnd io_addr + 3 /* rw SCSI command bits 0x0c */
-#define esp_status io_addr + 4 /* ro ESP status register 0x10 */
-#define esp_busid esp_status /* wo Bus ID for select/reselect 0x10 */
-#define esp_intrpt io_addr + 5 /* ro Kind of interrupt 0x14 */
-#define esp_timeo esp_intrpt /* wo Timeout value for select/resel 0x14 */
-#define esp_sstep io_addr + 6 /* ro Sequence step register 0x18 */
-#define esp_stp esp_sstep /* wo Transfer period per sync 0x18 */
-#define esp_fflags io_addr + 7 /* ro Bits of current FIFO info 0x1c */
-#define esp_soff esp_fflags /* wo Sync offset 0x1c */
-#define esp_cfg1 io_addr + 8 /* rw First configuration register 0x20 */
-#define esp_cfact io_addr + 9 /* wo Clock conversion factor 0x24 */
-#define esp_ctest io_addr + 10 /* wo Chip test register 0x28 */
-#define esp_cfg2 io_addr + 11 /* rw Second configuration register 0x2c */
-
- /* The following is only found on the 53C9X series SCSI chips */
-#define esp_cfg3 io_addr + 12 /* rw Third configuration register 0x30 */
-#define esp_cfg4 io_addr + 13 /* rw Fourth configuration register 0x34 */
-
- /* The following is found on all chips except the NCR53C90 (ESP100) */
-#define esp_tchi io_addr + 14 /* rw High bits of transfer count 0x38 */
-#define esp_uid esp_tchi /* ro Unique ID code 0x38 */
-#define esp_fgrnd io_addr + 15 /* rw Data base for fifo 0x3c */
-};
-
-#endif /* !defined(__i386__) && !defined(__x86_64__) */
-
-/* Various revisions of the ESP board. */
-enum esp_rev {
- esp100 = 0x00, /* NCR53C90 - very broken */
- esp100a = 0x01, /* NCR53C90A */
- esp236 = 0x02,
- fas236 = 0x03,
- fas100a = 0x04,
- fast = 0x05,
- fas366 = 0x06,
- fas216 = 0x07,
- fsc = 0x08, /* SYM53C94-2 */
- espunknown = 0x09
-};
-
-/* We allocate one of these for each scsi device and attach it to
- * SDptr->hostdata for use in the driver
- */
-struct esp_device {
- unsigned char sync_min_period;
- unsigned char sync_max_offset;
- unsigned sync:1;
- unsigned wide:1;
- unsigned disconnect:1;
-};
-
-/* We get one of these for each ESP probed. */
-struct NCR_ESP {
- struct NCR_ESP *next; /* Next ESP on probed or NULL */
- struct ESP_regs *eregs; /* All esp registers */
- int dma; /* Who I do transfers with. */
- void *dregs; /* And his registers. */
- struct Scsi_Host *ehost; /* Backpointer to SCSI Host */
-
- void *edev; /* Pointer to controller base/SBus */
- int esp_id; /* Unique per-ESP ID number */
-
- /* ESP Configuration Registers */
- unsigned char config1; /* Copy of the 1st config register */
- unsigned char config2; /* Copy of the 2nd config register */
- unsigned char config3[16]; /* Copy of the 3rd config register */
-
- /* The current command we are sending to the ESP chip. This esp_command
- * ptr needs to be mapped in DVMA area so we can send commands and read
- * from the ESP fifo without burning precious CPU cycles. Programmed I/O
- * sucks when we have the DVMA to do it for us. The ESP is stupid and will
- * only send out 6, 10, and 12 byte SCSI commands, others we need to send
- * one byte at a time. esp_slowcmd being set says that we are doing one
- * of the command types ESP doesn't understand, esp_scmdp keeps track of
- * which byte we are sending, esp_scmdleft says how many bytes to go.
- */
- volatile unchar *esp_command; /* Location of command (CPU view) */
- __u32 esp_command_dvma; /* Location of command (DVMA view) */
- unsigned char esp_clen; /* Length of this command */
- unsigned char esp_slowcmd;
- unsigned char *esp_scmdp;
- unsigned char esp_scmdleft;
-
- /* The following are used to determine the cause of an IRQ. Upon every
- * IRQ entry we synchronize these with the hardware registers.
- */
- unchar ireg; /* Copy of ESP interrupt register */
- unchar sreg; /* Same for ESP status register */
- unchar seqreg; /* The ESP sequence register */
-
- /* The following is set when a premature interrupt condition is detected
- * in some FAS revisions.
- */
- unchar fas_premature_intr_workaround;
-
- /* To save register writes to the ESP, which can be expensive, we
- * keep track of the previous value that various registers had for
- * the last target we connected to. If they are the same for the
- * current target, we skip the register writes as they are not needed.
- */
- unchar prev_soff, prev_stp, prev_cfg3;
-
- /* For each target we keep track of save/restore data
- * pointer information. This needs to be updated majorly
- * when we add support for tagged queueing. -DaveM
- */
- struct esp_pointers {
- char *saved_ptr;
- struct scatterlist *saved_buffer;
- int saved_this_residual;
- int saved_buffers_residual;
- } data_pointers[16] /*XXX [MAX_TAGS_PER_TARGET]*/;
-
- /* Clock periods, frequencies, synchronization, etc. */
- unsigned int cfreq; /* Clock frequency in HZ */
- unsigned int cfact; /* Clock conversion factor */
- unsigned int ccycle; /* One ESP clock cycle */
- unsigned int ctick; /* One ESP clock time */
- unsigned int radelay; /* FAST chip req/ack delay */
- unsigned int neg_defp; /* Default negotiation period */
- unsigned int sync_defp; /* Default sync transfer period */
- unsigned int max_period; /* longest our period can be */
- unsigned int min_period; /* shortest period we can withstand */
- /* For slow to medium speed input clock rates we shoot for 5mb/s,
- * but for high input clock rates we try to do 10mb/s although I
- * don't think a transfer can even run that fast with an ESP even
- * with DMA2 scatter gather pipelining.
- */
-#define SYNC_DEFP_SLOW 0x32 /* 5mb/s */
-#define SYNC_DEFP_FAST 0x19 /* 10mb/s */
-
- unsigned int snip; /* Sync. negotiation in progress */
- unsigned int wnip; /* WIDE negotiation in progress */
- unsigned int targets_present; /* targets spoken to before */
-
- int current_transfer_size; /* Set at beginning of data dma */
-
- unchar espcmdlog[32]; /* Log of current esp cmds sent. */
- unchar espcmdent; /* Current entry in esp cmd log. */
-
- /* Misc. info about this ESP */
- enum esp_rev erev; /* ESP revision */
- int irq; /* IRQ for this ESP */
- int scsi_id; /* Who am I as initiator? */
- int scsi_id_mask; /* Bitmask of 'me'. */
- int diff; /* Differential SCSI bus? */
- int slot; /* Slot the adapter occupies */
-
- /* Our command queues, only one cmd lives in the current_SC queue. */
- Scsi_Cmnd *issue_SC; /* Commands to be issued */
- Scsi_Cmnd *current_SC; /* Who is currently working the bus */
- Scsi_Cmnd *disconnected_SC; /* Commands disconnected from the bus */
-
- /* Message goo */
- unchar cur_msgout[16];
- unchar cur_msgin[16];
- unchar prevmsgout, prevmsgin;
- unchar msgout_len, msgin_len;
- unchar msgout_ctr, msgin_ctr;
-
- /* States that we cannot keep in the per cmd structure because they
- * cannot be assosciated with any specific command.
- */
- unchar resetting_bus;
- wait_queue_head_t reset_queue;
-
- unchar do_pio_cmds; /* Do command transfer with pio */
-
- /* How much bits do we have to shift the registers */
- unsigned char shift;
-
- /* Functions handling DMA
- */
- /* Required functions */
- int (*dma_bytes_sent)(struct NCR_ESP *, int);
- int (*dma_can_transfer)(struct NCR_ESP *, Scsi_Cmnd *);
- void (*dma_dump_state)(struct NCR_ESP *);
- void (*dma_init_read)(struct NCR_ESP *, __u32, int);
- void (*dma_init_write)(struct NCR_ESP *, __u32, int);
- void (*dma_ints_off)(struct NCR_ESP *);
- void (*dma_ints_on)(struct NCR_ESP *);
- int (*dma_irq_p)(struct NCR_ESP *);
- int (*dma_ports_p)(struct NCR_ESP *);
- void (*dma_setup)(struct NCR_ESP *, __u32, int, int);
-
- /* Optional functions (i.e. may be initialized to 0) */
- void (*dma_barrier)(struct NCR_ESP *);
- void (*dma_drain)(struct NCR_ESP *);
- void (*dma_invalidate)(struct NCR_ESP *);
- void (*dma_irq_entry)(struct NCR_ESP *);
- void (*dma_irq_exit)(struct NCR_ESP *);
- void (*dma_led_off)(struct NCR_ESP *);
- void (*dma_led_on)(struct NCR_ESP *);
- void (*dma_poll)(struct NCR_ESP *, unsigned char *);
- void (*dma_reset)(struct NCR_ESP *);
-
- /* Optional virtual DMA functions */
- void (*dma_mmu_get_scsi_one)(struct NCR_ESP *, Scsi_Cmnd *);
- void (*dma_mmu_get_scsi_sgl)(struct NCR_ESP *, Scsi_Cmnd *);
- void (*dma_mmu_release_scsi_one)(struct NCR_ESP *, Scsi_Cmnd *);
- void (*dma_mmu_release_scsi_sgl)(struct NCR_ESP *, Scsi_Cmnd *);
- void (*dma_advance_sg)(Scsi_Cmnd *);
-};
-
-/* Bitfield meanings for the above registers. */
-
-/* ESP config reg 1, read-write, found on all ESP chips */
-#define ESP_CONFIG1_ID 0x07 /* My BUS ID bits */
-#define ESP_CONFIG1_CHTEST 0x08 /* Enable ESP chip tests */
-#define ESP_CONFIG1_PENABLE 0x10 /* Enable parity checks */
-#define ESP_CONFIG1_PARTEST 0x20 /* Parity test mode enabled? */
-#define ESP_CONFIG1_SRRDISAB 0x40 /* Disable SCSI reset reports */
-#define ESP_CONFIG1_SLCABLE 0x80 /* Enable slow cable mode */
-
-/* ESP config reg 2, read-write, found only on esp100a+esp200+esp236+fsc chips */
-#define ESP_CONFIG2_DMAPARITY 0x01 /* enable DMA Parity (200,236,fsc) */
-#define ESP_CONFIG2_REGPARITY 0x02 /* enable reg Parity (200,236,fsc) */
-#define ESP_CONFIG2_BADPARITY 0x04 /* Bad parity target abort */
-#define ESP_CONFIG2_SCSI2ENAB 0x08 /* Enable SCSI-2 features (tmode only) */
-#define ESP_CONFIG2_HI 0x10 /* High Impedance DREQ ??? */
-#define ESP_CONFIG2_HMEFENAB 0x10 /* HME features enable */
-#define ESP_CONFIG2_BCM 0x20 /* Enable byte-ctrl (236,fsc) */
-#define ESP_CONFIG2_FENAB 0x40 /* Enable features (fas100,esp216,fsc) */
-#define ESP_CONFIG2_SPL 0x40 /* Enable status-phase latch (esp236) */
-#define ESP_CONFIG2_RFB 0x80 /* Reserve FIFO byte (fsc) */
-#define ESP_CONFIG2_MAGIC 0xe0 /* Invalid bits... */
-
-/* ESP config register 3 read-write, found only esp236+fas236+fas100a+fsc chips */
-#define ESP_CONFIG3_FCLOCK 0x01 /* FAST SCSI clock rate (esp100a/fas366) */
-#define ESP_CONFIG3_TEM 0x01 /* Enable thresh-8 mode (esp/fas236/fsc) */
-#define ESP_CONFIG3_FAST 0x02 /* Enable FAST SCSI (esp100a) */
-#define ESP_CONFIG3_ADMA 0x02 /* Enable alternate-dma (esp/fas236/fsc) */
-#define ESP_CONFIG3_TENB 0x04 /* group2 SCSI2 support (esp100a) */
-#define ESP_CONFIG3_SRB 0x04 /* Save residual byte (esp/fas236/fsc) */
-#define ESP_CONFIG3_TMS 0x08 /* Three-byte msg's ok (esp100a) */
-#define ESP_CONFIG3_FCLK 0x08 /* Fast SCSI clock rate (esp/fas236/fsc) */
-#define ESP_CONFIG3_IDMSG 0x10 /* ID message checking (esp100a) */
-#define ESP_CONFIG3_FSCSI 0x10 /* Enable FAST SCSI (esp/fas236/fsc) */
-#define ESP_CONFIG3_GTM 0x20 /* group2 SCSI2 support (esp/fas236/fsc) */
-#define ESP_CONFIG3_TBMS 0x40 /* Three-byte msg's ok (esp/fas236/fsc) */
-#define ESP_CONFIG3_IMS 0x80 /* ID msg chk'ng (esp/fas236/fsc) */
-
-/* ESP config register 4 read-write, found only on fsc chips */
-#define ESP_CONFIG4_BBTE 0x01 /* Back-to-Back transfer enable */
-#define ESP_CONFIG4_TEST 0x02 /* Transfer counter test mode */
-#define ESP_CONFIG4_EAN 0x04 /* Enable Active Negotiation */
-
-/* ESP command register read-write */
-/* Group 1 commands: These may be sent at any point in time to the ESP
- * chip. None of them can generate interrupts 'cept
- * the "SCSI bus reset" command if you have not disabled
- * SCSI reset interrupts in the config1 ESP register.
- */
-#define ESP_CMD_NULL 0x00 /* Null command, ie. a nop */
-#define ESP_CMD_FLUSH 0x01 /* FIFO Flush */
-#define ESP_CMD_RC 0x02 /* Chip reset */
-#define ESP_CMD_RS 0x03 /* SCSI bus reset */
-
-/* Group 2 commands: ESP must be an initiator and connected to a target
- * for these commands to work.
- */
-#define ESP_CMD_TI 0x10 /* Transfer Information */
-#define ESP_CMD_ICCSEQ 0x11 /* Initiator cmd complete sequence */
-#define ESP_CMD_MOK 0x12 /* Message okie-dokie */
-#define ESP_CMD_TPAD 0x18 /* Transfer Pad */
-#define ESP_CMD_SATN 0x1a /* Set ATN */
-#define ESP_CMD_RATN 0x1b /* De-assert ATN */
-
-/* Group 3 commands: ESP must be in the MSGOUT or MSGIN state and be connected
- * to a target as the initiator for these commands to work.
- */
-#define ESP_CMD_SMSG 0x20 /* Send message */
-#define ESP_CMD_SSTAT 0x21 /* Send status */
-#define ESP_CMD_SDATA 0x22 /* Send data */
-#define ESP_CMD_DSEQ 0x23 /* Discontinue Sequence */
-#define ESP_CMD_TSEQ 0x24 /* Terminate Sequence */
-#define ESP_CMD_TCCSEQ 0x25 /* Target cmd cmplt sequence */
-#define ESP_CMD_DCNCT 0x27 /* Disconnect */
-#define ESP_CMD_RMSG 0x28 /* Receive Message */
-#define ESP_CMD_RCMD 0x29 /* Receive Command */
-#define ESP_CMD_RDATA 0x2a /* Receive Data */
-#define ESP_CMD_RCSEQ 0x2b /* Receive cmd sequence */
-
-/* Group 4 commands: The ESP must be in the disconnected state and must
- * not be connected to any targets as initiator for
- * these commands to work.
- */
-#define ESP_CMD_RSEL 0x40 /* Reselect */
-#define ESP_CMD_SEL 0x41 /* Select w/o ATN */
-#define ESP_CMD_SELA 0x42 /* Select w/ATN */
-#define ESP_CMD_SELAS 0x43 /* Select w/ATN & STOP */
-#define ESP_CMD_ESEL 0x44 /* Enable selection */
-#define ESP_CMD_DSEL 0x45 /* Disable selections */
-#define ESP_CMD_SA3 0x46 /* Select w/ATN3 */
-#define ESP_CMD_RSEL3 0x47 /* Reselect3 */
-
-/* This bit enables the ESP's DMA */
-#define ESP_CMD_DMA 0x80 /* Do DMA? */
-
-/* ESP status register read-only */
-#define ESP_STAT_PIO 0x01 /* IO phase bit */
-#define ESP_STAT_PCD 0x02 /* CD phase bit */
-#define ESP_STAT_PMSG 0x04 /* MSG phase bit */
-#define ESP_STAT_PMASK 0x07 /* Mask of phase bits */
-#define ESP_STAT_TDONE 0x08 /* Transfer Completed */
-#define ESP_STAT_TCNT 0x10 /* Transfer Counter Is Zero */
-#define ESP_STAT_PERR 0x20 /* Parity error */
-#define ESP_STAT_SPAM 0x40 /* Real bad error */
-/* This indicates the 'interrupt pending' condition, it is a reserved
- * bit on old revs of the ESP (ESP100, ESP100A, FAS100A).
- */
-#define ESP_STAT_INTR 0x80 /* Interrupt */
-
-/* The status register can be masked with ESP_STAT_PMASK and compared
- * with the following values to determine the current phase the ESP
- * (at least thinks it) is in. For our purposes we also add our own
- * software 'done' bit for our phase management engine.
- */
-#define ESP_DOP (0) /* Data Out */
-#define ESP_DIP (ESP_STAT_PIO) /* Data In */
-#define ESP_CMDP (ESP_STAT_PCD) /* Command */
-#define ESP_STATP (ESP_STAT_PCD|ESP_STAT_PIO) /* Status */
-#define ESP_MOP (ESP_STAT_PMSG|ESP_STAT_PCD) /* Message Out */
-#define ESP_MIP (ESP_STAT_PMSG|ESP_STAT_PCD|ESP_STAT_PIO) /* Message In */
-
-/* ESP interrupt register read-only */
-#define ESP_INTR_S 0x01 /* Select w/o ATN */
-#define ESP_INTR_SATN 0x02 /* Select w/ATN */
-#define ESP_INTR_RSEL 0x04 /* Reselected */
-#define ESP_INTR_FDONE 0x08 /* Function done */
-#define ESP_INTR_BSERV 0x10 /* Bus service */
-#define ESP_INTR_DC 0x20 /* Disconnect */
-#define ESP_INTR_IC 0x40 /* Illegal command given */
-#define ESP_INTR_SR 0x80 /* SCSI bus reset detected */
-
-/* Interrupt status macros */
-#define ESP_SRESET_IRQ(esp) ((esp)->intreg & (ESP_INTR_SR))
-#define ESP_ILLCMD_IRQ(esp) ((esp)->intreg & (ESP_INTR_IC))
-#define ESP_SELECT_WITH_ATN_IRQ(esp) ((esp)->intreg & (ESP_INTR_SATN))
-#define ESP_SELECT_WITHOUT_ATN_IRQ(esp) ((esp)->intreg & (ESP_INTR_S))
-#define ESP_SELECTION_IRQ(esp) ((ESP_SELECT_WITH_ATN_IRQ(esp)) || \
- (ESP_SELECT_WITHOUT_ATN_IRQ(esp)))
-#define ESP_RESELECTION_IRQ(esp) ((esp)->intreg & (ESP_INTR_RSEL))
-
-/* ESP sequence step register read-only */
-#define ESP_STEP_VBITS 0x07 /* Valid bits */
-#define ESP_STEP_ASEL 0x00 /* Selection&Arbitrate cmplt */
-#define ESP_STEP_SID 0x01 /* One msg byte sent */
-#define ESP_STEP_NCMD 0x02 /* Was not in command phase */
-#define ESP_STEP_PPC 0x03 /* Early phase chg caused cmnd
- * bytes to be lost
- */
-#define ESP_STEP_FINI4 0x04 /* Command was sent ok */
-
-/* Ho hum, some ESP's set the step register to this as well... */
-#define ESP_STEP_FINI5 0x05
-#define ESP_STEP_FINI6 0x06
-#define ESP_STEP_FINI7 0x07
-#define ESP_STEP_SOM 0x08 /* Synchronous Offset Max */
-
-/* ESP chip-test register read-write */
-#define ESP_TEST_TARG 0x01 /* Target test mode */
-#define ESP_TEST_INI 0x02 /* Initiator test mode */
-#define ESP_TEST_TS 0x04 /* Tristate test mode */
-
-/* ESP unique ID register read-only, found on fas236+fas100a+fsc only */
-#define ESP_UID_F100A 0x00 /* FAS100A */
-#define ESP_UID_F236 0x02 /* FAS236 */
-#define ESP_UID_FSC 0xa2 /* NCR53CF9x-2 */
-#define ESP_UID_REV 0x07 /* ESP revision */
-#define ESP_UID_FAM 0xf8 /* ESP family */
-
-/* ESP fifo flags register read-only */
-/* Note that the following implies a 16 byte FIFO on the ESP. */
-#define ESP_FF_FBYTES 0x1f /* Num bytes in FIFO */
-#define ESP_FF_ONOTZERO 0x20 /* offset ctr not zero (esp100,fsc) */
-#define ESP_FF_SSTEP 0xe0 /* Sequence step */
-
-/* ESP clock conversion factor register write-only */
-#define ESP_CCF_F0 0x00 /* 35.01MHz - 40MHz */
-#define ESP_CCF_NEVER 0x01 /* Set it to this and die */
-#define ESP_CCF_F2 0x02 /* 10MHz */
-#define ESP_CCF_F3 0x03 /* 10.01MHz - 15MHz */
-#define ESP_CCF_F4 0x04 /* 15.01MHz - 20MHz */
-#define ESP_CCF_F5 0x05 /* 20.01MHz - 25MHz */
-#define ESP_CCF_F6 0x06 /* 25.01MHz - 30MHz */
-#define ESP_CCF_F7 0x07 /* 30.01MHz - 35MHz */
-
-#define ESP_BUS_TIMEOUT 275 /* In milli-seconds */
-#define ESP_TIMEO_CONST 8192
-#define FSC_TIMEO_CONST 7668
-#define ESP_NEG_DEFP(mhz, cfact) \
- ((ESP_BUS_TIMEOUT * ((mhz) / 1000)) / (8192 * (cfact)))
-#define FSC_NEG_DEFP(mhz, cfact) \
- ((ESP_BUS_TIMEOUT * ((mhz) / 1000)) / (7668 * (cfact)))
-#define ESP_MHZ_TO_CYCLE(mhertz) ((1000000000) / ((mhertz) / 1000))
-#define ESP_TICK(ccf, cycle) ((7682 * (ccf) * (cycle) / 1000))
-
-
-/* UGLY, UGLY, UGLY! */
-extern int nesps, esps_in_use, esps_running;
-
-/* For our interrupt engine. */
-#define for_each_esp(esp) \
- for((esp) = espchain; (esp); (esp) = (esp)->next)
-
-
-/* External functions */
-extern void esp_bootup_reset(struct NCR_ESP *esp, struct ESP_regs *eregs);
-extern struct NCR_ESP *esp_allocate(struct scsi_host_template *, void *, int);
-extern void esp_deallocate(struct NCR_ESP *);
-extern void esp_release(void);
-extern void esp_initialize(struct NCR_ESP *);
-extern irqreturn_t esp_intr(int, void *);
-extern const char *esp_info(struct Scsi_Host *);
-extern int esp_queue(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
-extern int esp_abort(Scsi_Cmnd *);
-extern int esp_reset(Scsi_Cmnd *);
-extern int esp_proc_info(struct Scsi_Host *shost, char *buffer, char **start, off_t offset, int length,
- int inout);
-extern int esp_slave_alloc(struct scsi_device *);
-extern void esp_slave_destroy(struct scsi_device *);
-#endif /* !(NCR53C9X_H) */
diff --git a/drivers/scsi/blz1230.c b/drivers/scsi/blz1230.c
deleted file mode 100644
index 23f7c24..0000000
--- a/drivers/scsi/blz1230.c
+++ /dev/null
@@ -1,353 +0,0 @@
-/* blz1230.c: Driver for Blizzard 1230 SCSI IV Controller.
- *
- * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
- *
- * This driver is based on the CyberStorm driver, hence the occasional
- * reference to CyberStorm.
- */
-
-/* TODO:
- *
- * 1) Figure out how to make a cleaner merge with the sparc driver with regard
- * to the caches and the Sparc MMU mapping.
- * 2) Make as few routines required outside the generic driver. A lot of the
- * routines in this file used to be inline!
- */
-
-#include <linux/module.h>
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <linux/zorro.h>
-#include <asm/irq.h>
-#include <asm/amigaints.h>
-#include <asm/amigahw.h>
-
-#include <asm/pgtable.h>
-
-#define MKIV 1
-
-/* The controller registers can be found in the Z2 config area at these
- * offsets:
- */
-#define BLZ1230_ESP_ADDR 0x8000
-#define BLZ1230_DMA_ADDR 0x10000
-#define BLZ1230II_ESP_ADDR 0x10000
-#define BLZ1230II_DMA_ADDR 0x10021
-
-
-/* The Blizzard 1230 DMA interface
- * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- * Only two things can be programmed in the Blizzard DMA:
- * 1) The data direction is controlled by the status of bit 31 (1 = write)
- * 2) The source/dest address (word aligned, shifted one right) in bits 30-0
- *
- * Program DMA by first latching the highest byte of the address/direction
- * (i.e. bits 31-24 of the long word constructed as described in steps 1+2
- * above). Then write each byte of the address/direction (starting with the
- * top byte, working down) to the DMA address register.
- *
- * Figure out interrupt status by reading the ESP status byte.
- */
-struct blz1230_dma_registers {
- volatile unsigned char dma_addr; /* DMA address [0x0000] */
- unsigned char dmapad2[0x7fff];
- volatile unsigned char dma_latch; /* DMA latch [0x8000] */
-};
-
-struct blz1230II_dma_registers {
- volatile unsigned char dma_addr; /* DMA address [0x0000] */
- unsigned char dmapad2[0xf];
- volatile unsigned char dma_latch; /* DMA latch [0x0010] */
-};
-
-#define BLZ1230_DMA_WRITE 0x80000000
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are transferred to the ESP chip
- * via PIO.
- */
-
-/***************************************************************** Detection */
-int __init blz1230_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct zorro_dev *z = NULL;
- unsigned long address;
- struct ESP_regs *eregs;
- unsigned long board;
-
-#if MKIV
-#define REAL_BLZ1230_ID ZORRO_PROD_PHASE5_BLIZZARD_1230_IV_1260
-#define REAL_BLZ1230_ESP_ADDR BLZ1230_ESP_ADDR
-#define REAL_BLZ1230_DMA_ADDR BLZ1230_DMA_ADDR
-#else
-#define REAL_BLZ1230_ID ZORRO_PROD_PHASE5_BLIZZARD_1230_II_FASTLANE_Z3_CYBERSCSI_CYBERSTORM060
-#define REAL_BLZ1230_ESP_ADDR BLZ1230II_ESP_ADDR
-#define REAL_BLZ1230_DMA_ADDR BLZ1230II_DMA_ADDR
-#endif
-
- if ((z = zorro_find_device(REAL_BLZ1230_ID, z))) {
- board = z->resource.start;
- if (request_mem_region(board+REAL_BLZ1230_ESP_ADDR,
- sizeof(struct ESP_regs), "NCR53C9x")) {
- /* Do some magic to figure out if the blizzard is
- * equipped with a SCSI controller
- */
- address = ZTWO_VADDR(board);
- eregs = (struct ESP_regs *)(address + REAL_BLZ1230_ESP_ADDR);
- esp = esp_allocate(tpnt, (void *)board + REAL_BLZ1230_ESP_ADDR,
- 0);
-
- esp_write(eregs->esp_cfg1, (ESP_CONFIG1_PENABLE | 7));
- udelay(5);
- if(esp_read(eregs->esp_cfg1) != (ESP_CONFIG1_PENABLE | 7))
- goto err_out;
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = 0;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_led_on = 0;
- esp->dma_led_off = 0;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
-
- /* SCSI chip speed */
- esp->cfreq = 40000000;
-
- /* The DMA registers on the Blizzard are mapped
- * relative to the device (i.e. in the same Zorro
- * I/O block).
- */
- esp->dregs = (void *)(address + REAL_BLZ1230_DMA_ADDR);
-
- /* ESP register base */
- esp->eregs = eregs;
-
- /* Set the command buffer */
- esp->esp_command = cmd_buffer;
- esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer);
-
- esp->irq = IRQ_AMIGA_PORTS;
- esp->slot = board+REAL_BLZ1230_ESP_ADDR;
- if (request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
- "Blizzard 1230 SCSI IV", esp->ehost))
- goto err_out;
-
- /* Figure out our scsi ID on the bus */
- esp->scsi_id = 7;
-
- /* We don't have a differential SCSI-bus. */
- esp->diff = 0;
-
- esp_initialize(esp);
-
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use);
- esps_running = esps_in_use;
- return esps_in_use;
- }
- }
- return 0;
-
- err_out:
- scsi_unregister(esp->ehost);
- esp_deallocate(esp);
- release_mem_region(board+REAL_BLZ1230_ESP_ADDR,
- sizeof(struct ESP_regs));
- return 0;
-}
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Since the Blizzard DMA is fully dedicated to the ESP chip,
- * the number of bytes sent (to the ESP chip) equals the number
- * of bytes in the FIFO - there is no buffering in the DMA controller.
- * XXXX Do I read this right? It is from host to ESP, right?
- */
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- /* I don't think there's any limit on the Blizzard DMA. So we use what
- * the ESP chip can handle (24 bit).
- */
- unsigned long sz = sp->SCp.this_residual;
- if(sz > 0x1000000)
- sz = 0x1000000;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- ESPLOG(("intreq:<%04x>, intena:<%04x>\n",
- amiga_custom.intreqr, amiga_custom.intenar));
-}
-
-void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
-{
-#if MKIV
- struct blz1230_dma_registers *dregs =
- (struct blz1230_dma_registers *) (esp->dregs);
-#else
- struct blz1230II_dma_registers *dregs =
- (struct blz1230II_dma_registers *) (esp->dregs);
-#endif
-
- cache_clear(addr, length);
-
- addr >>= 1;
- addr &= ~(BLZ1230_DMA_WRITE);
-
- /* First set latch */
- dregs->dma_latch = (addr >> 24) & 0xff;
-
- /* Then pump the address to the DMA address register */
-#if MKIV
- dregs->dma_addr = (addr >> 24) & 0xff;
-#endif
- dregs->dma_addr = (addr >> 16) & 0xff;
- dregs->dma_addr = (addr >> 8) & 0xff;
- dregs->dma_addr = (addr ) & 0xff;
-}
-
-void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
-{
-#if MKIV
- struct blz1230_dma_registers *dregs =
- (struct blz1230_dma_registers *) (esp->dregs);
-#else
- struct blz1230II_dma_registers *dregs =
- (struct blz1230II_dma_registers *) (esp->dregs);
-#endif
-
- cache_push(addr, length);
-
- addr >>= 1;
- addr |= BLZ1230_DMA_WRITE;
-
- /* First set latch */
- dregs->dma_latch = (addr >> 24) & 0xff;
-
- /* Then pump the address to the DMA address register */
-#if MKIV
- dregs->dma_addr = (addr >> 24) & 0xff;
-#endif
- dregs->dma_addr = (addr >> 16) & 0xff;
- dregs->dma_addr = (addr >> 8) & 0xff;
- dregs->dma_addr = (addr ) & 0xff;
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(esp->irq);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(esp->irq);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- return (esp_read(esp->eregs->esp_status) & ESP_STAT_INTR);
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return ((amiga_custom.intenar) & IF_PORTS);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if(write){
- dma_init_read(esp, addr, count);
- } else {
- dma_init_write(esp, addr, count);
- }
-}
-
-#define HOSTS_C
-
-int blz1230_esp_release(struct Scsi_Host *instance)
-{
-#ifdef MODULE
- unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
- esp_deallocate((struct NCR_ESP *)instance->hostdata);
- esp_release();
- release_mem_region(address, sizeof(struct ESP_regs));
- free_irq(IRQ_AMIGA_PORTS, esp_intr);
-#endif
- return 1;
-}
-
-
-static struct scsi_host_template driver_template = {
- .proc_name = "esp-blz1230",
- .proc_info = esp_proc_info,
- .name = "Blizzard1230 SCSI IV",
- .detect = blz1230_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = blz1230_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/blz2060.c b/drivers/scsi/blz2060.c
deleted file mode 100644
index b6203ec..0000000
--- a/drivers/scsi/blz2060.c
+++ /dev/null
@@ -1,306 +0,0 @@
-/* blz2060.c: Driver for Blizzard 2060 SCSI Controller.
- *
- * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
- *
- * This driver is based on the CyberStorm driver, hence the occasional
- * reference to CyberStorm.
- */
-
-/* TODO:
- *
- * 1) Figure out how to make a cleaner merge with the sparc driver with regard
- * to the caches and the Sparc MMU mapping.
- * 2) Make as few routines required outside the generic driver. A lot of the
- * routines in this file used to be inline!
- */
-
-#include <linux/module.h>
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <linux/zorro.h>
-#include <asm/irq.h>
-#include <asm/amigaints.h>
-#include <asm/amigahw.h>
-
-#include <asm/pgtable.h>
-
-/* The controller registers can be found in the Z2 config area at these
- * offsets:
- */
-#define BLZ2060_ESP_ADDR 0x1ff00
-#define BLZ2060_DMA_ADDR 0x1ffe0
-
-
-/* The Blizzard 2060 DMA interface
- * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- * Only two things can be programmed in the Blizzard DMA:
- * 1) The data direction is controlled by the status of bit 31 (1 = write)
- * 2) The source/dest address (word aligned, shifted one right) in bits 30-0
- *
- * Figure out interrupt status by reading the ESP status byte.
- */
-struct blz2060_dma_registers {
- volatile unsigned char dma_led_ctrl; /* DMA led control [0x000] */
- unsigned char dmapad1[0x0f];
- volatile unsigned char dma_addr0; /* DMA address (MSB) [0x010] */
- unsigned char dmapad2[0x03];
- volatile unsigned char dma_addr1; /* DMA address [0x014] */
- unsigned char dmapad3[0x03];
- volatile unsigned char dma_addr2; /* DMA address [0x018] */
- unsigned char dmapad4[0x03];
- volatile unsigned char dma_addr3; /* DMA address (LSB) [0x01c] */
-};
-
-#define BLZ2060_DMA_WRITE 0x80000000
-
-/* DMA control bits */
-#define BLZ2060_DMA_LED 0x02 /* HD led control 1 = off */
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static void dma_led_off(struct NCR_ESP *esp);
-static void dma_led_on(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are transferred to the ESP chip
- * via PIO.
- */
-
-/***************************************************************** Detection */
-int __init blz2060_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct zorro_dev *z = NULL;
- unsigned long address;
-
- if ((z = zorro_find_device(ZORRO_PROD_PHASE5_BLIZZARD_2060, z))) {
- unsigned long board = z->resource.start;
- if (request_mem_region(board+BLZ2060_ESP_ADDR,
- sizeof(struct ESP_regs), "NCR53C9x")) {
- esp = esp_allocate(tpnt, (void *)board + BLZ2060_ESP_ADDR, 0);
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = 0;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_led_on = &dma_led_on;
- esp->dma_led_off = &dma_led_off;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
-
- /* SCSI chip speed */
- esp->cfreq = 40000000;
-
- /* The DMA registers on the Blizzard are mapped
- * relative to the device (i.e. in the same Zorro
- * I/O block).
- */
- address = (unsigned long)ZTWO_VADDR(board);
- esp->dregs = (void *)(address + BLZ2060_DMA_ADDR);
-
- /* ESP register base */
- esp->eregs = (struct ESP_regs *)(address + BLZ2060_ESP_ADDR);
-
- /* Set the command buffer */
- esp->esp_command = cmd_buffer;
- esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer);
-
- esp->irq = IRQ_AMIGA_PORTS;
- request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
- "Blizzard 2060 SCSI", esp->ehost);
-
- /* Figure out our scsi ID on the bus */
- esp->scsi_id = 7;
-
- /* We don't have a differential SCSI-bus. */
- esp->diff = 0;
-
- esp_initialize(esp);
-
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use);
- esps_running = esps_in_use;
- return esps_in_use;
- }
- }
- return 0;
-}
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Since the Blizzard DMA is fully dedicated to the ESP chip,
- * the number of bytes sent (to the ESP chip) equals the number
- * of bytes in the FIFO - there is no buffering in the DMA controller.
- * XXXX Do I read this right? It is from host to ESP, right?
- */
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- /* I don't think there's any limit on the Blizzard DMA. So we use what
- * the ESP chip can handle (24 bit).
- */
- unsigned long sz = sp->SCp.this_residual;
- if(sz > 0x1000000)
- sz = 0x1000000;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- ESPLOG(("intreq:<%04x>, intena:<%04x>\n",
- amiga_custom.intreqr, amiga_custom.intenar));
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct blz2060_dma_registers *dregs =
- (struct blz2060_dma_registers *) (esp->dregs);
-
- cache_clear(addr, length);
-
- addr >>= 1;
- addr &= ~(BLZ2060_DMA_WRITE);
- dregs->dma_addr3 = (addr ) & 0xff;
- dregs->dma_addr2 = (addr >> 8) & 0xff;
- dregs->dma_addr1 = (addr >> 16) & 0xff;
- dregs->dma_addr0 = (addr >> 24) & 0xff;
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct blz2060_dma_registers *dregs =
- (struct blz2060_dma_registers *) (esp->dregs);
-
- cache_push(addr, length);
-
- addr >>= 1;
- addr |= BLZ2060_DMA_WRITE;
- dregs->dma_addr3 = (addr ) & 0xff;
- dregs->dma_addr2 = (addr >> 8) & 0xff;
- dregs->dma_addr1 = (addr >> 16) & 0xff;
- dregs->dma_addr0 = (addr >> 24) & 0xff;
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(esp->irq);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(esp->irq);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- return (esp_read(esp->eregs->esp_status) & ESP_STAT_INTR);
-}
-
-static void dma_led_off(struct NCR_ESP *esp)
-{
- ((struct blz2060_dma_registers *) (esp->dregs))->dma_led_ctrl =
- BLZ2060_DMA_LED;
-}
-
-static void dma_led_on(struct NCR_ESP *esp)
-{
- ((struct blz2060_dma_registers *) (esp->dregs))->dma_led_ctrl = 0;
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return ((amiga_custom.intenar) & IF_PORTS);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if(write){
- dma_init_read(esp, addr, count);
- } else {
- dma_init_write(esp, addr, count);
- }
-}
-
-#define HOSTS_C
-
-int blz2060_esp_release(struct Scsi_Host *instance)
-{
-#ifdef MODULE
- unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
-
- esp_deallocate((struct NCR_ESP *)instance->hostdata);
- esp_release();
- release_mem_region(address, sizeof(struct ESP_regs));
- free_irq(IRQ_AMIGA_PORTS, esp_intr);
-#endif
- return 1;
-}
-
-
-static struct scsi_host_template driver_template = {
- .proc_name = "esp-blz2060",
- .proc_info = esp_proc_info,
- .name = "Blizzard2060 SCSI",
- .detect = blz2060_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = blz2060_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/cyberstorm.c b/drivers/scsi/cyberstorm.c
deleted file mode 100644
index c6b98a4..0000000
--- a/drivers/scsi/cyberstorm.c
+++ /dev/null
@@ -1,377 +0,0 @@
-/* cyberstorm.c: Driver for CyberStorm SCSI Controller.
- *
- * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
- *
- * The CyberStorm SCSI driver is based on David S. Miller's ESP driver
- * for the Sparc computers.
- *
- * This work was made possible by Phase5 who willingly (and most generously)
- * supported me with hardware and all the information I needed.
- */
-
-/* TODO:
- *
- * 1) Figure out how to make a cleaner merge with the sparc driver with regard
- * to the caches and the Sparc MMU mapping.
- * 2) Make as few routines required outside the generic driver. A lot of the
- * routines in this file used to be inline!
- */
-
-#include <linux/module.h>
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <linux/zorro.h>
-#include <asm/irq.h>
-#include <asm/amigaints.h>
-#include <asm/amigahw.h>
-
-#include <asm/pgtable.h>
-
-/* The controller registers can be found in the Z2 config area at these
- * offsets:
- */
-#define CYBER_ESP_ADDR 0xf400
-#define CYBER_DMA_ADDR 0xf800
-
-
-/* The CyberStorm DMA interface */
-struct cyber_dma_registers {
- volatile unsigned char dma_addr0; /* DMA address (MSB) [0x000] */
- unsigned char dmapad1[1];
- volatile unsigned char dma_addr1; /* DMA address [0x002] */
- unsigned char dmapad2[1];
- volatile unsigned char dma_addr2; /* DMA address [0x004] */
- unsigned char dmapad3[1];
- volatile unsigned char dma_addr3; /* DMA address (LSB) [0x006] */
- unsigned char dmapad4[0x3fb];
- volatile unsigned char cond_reg; /* DMA cond (ro) [0x402] */
-#define ctrl_reg cond_reg /* DMA control (wo) [0x402] */
-};
-
-/* DMA control bits */
-#define CYBER_DMA_LED 0x80 /* HD led control 1 = on */
-#define CYBER_DMA_WRITE 0x40 /* DMA direction. 1 = write */
-#define CYBER_DMA_Z3 0x20 /* 16 (Z2) or 32 (CHIP/Z3) bit DMA transfer */
-
-/* DMA status bits */
-#define CYBER_DMA_HNDL_INTR 0x80 /* DMA IRQ pending? */
-
-/* The bits below appears to be Phase5 Debug bits only; they were not
- * described by Phase5 so using them may seem a bit stupid...
- */
-#define CYBER_HOST_ID 0x02 /* If set, host ID should be 7, otherwise
- * it should be 6.
- */
-#define CYBER_SLOW_CABLE 0x08 /* If *not* set, assume SLOW_CABLE */
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static void dma_led_off(struct NCR_ESP *esp);
-static void dma_led_on(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-
-static unsigned char ctrl_data = 0; /* Keep backup of the stuff written
- * to ctrl_reg. Always write a copy
- * to this register when writing to
- * the hardware register!
- */
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are transferred to the ESP chip
- * via PIO.
- */
-
-/***************************************************************** Detection */
-int __init cyber_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct zorro_dev *z = NULL;
- unsigned long address;
-
- while ((z = zorro_find_device(ZORRO_WILDCARD, z))) {
- unsigned long board = z->resource.start;
- if ((z->id == ZORRO_PROD_PHASE5_BLIZZARD_1220_CYBERSTORM ||
- z->id == ZORRO_PROD_PHASE5_BLIZZARD_1230_II_FASTLANE_Z3_CYBERSCSI_CYBERSTORM060) &&
- request_mem_region(board+CYBER_ESP_ADDR,
- sizeof(struct ESP_regs), "NCR53C9x")) {
- /* Figure out if this is a CyberStorm or really a
- * Fastlane/Blizzard Mk II by looking at the board size.
- * CyberStorm maps 64kB
- * (ZORRO_PROD_PHASE5_BLIZZARD_1220_CYBERSTORM does anyway)
- */
- if(z->resource.end-board != 0xffff) {
- release_mem_region(board+CYBER_ESP_ADDR,
- sizeof(struct ESP_regs));
- return 0;
- }
- esp = esp_allocate(tpnt, (void *)board + CYBER_ESP_ADDR, 0);
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = 0;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_led_on = &dma_led_on;
- esp->dma_led_off = &dma_led_off;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
-
- /* SCSI chip speed */
- esp->cfreq = 40000000;
-
- /* The DMA registers on the CyberStorm are mapped
- * relative to the device (i.e. in the same Zorro
- * I/O block).
- */
- address = (unsigned long)ZTWO_VADDR(board);
- esp->dregs = (void *)(address + CYBER_DMA_ADDR);
-
- /* ESP register base */
- esp->eregs = (struct ESP_regs *)(address + CYBER_ESP_ADDR);
-
- /* Set the command buffer */
- esp->esp_command = cmd_buffer;
- esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer);
-
- esp->irq = IRQ_AMIGA_PORTS;
- request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
- "CyberStorm SCSI", esp->ehost);
- /* Figure out our scsi ID on the bus */
- /* The DMA cond flag contains a hardcoded jumper bit
- * which can be used to select host number 6 or 7.
- * However, even though it may change, we use a hardcoded
- * value of 7.
- */
- esp->scsi_id = 7;
-
- /* We don't have a differential SCSI-bus. */
- esp->diff = 0;
-
- esp_initialize(esp);
-
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use);
- esps_running = esps_in_use;
- return esps_in_use;
- }
- }
- return 0;
-}
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Since the CyberStorm DMA is fully dedicated to the ESP chip,
- * the number of bytes sent (to the ESP chip) equals the number
- * of bytes in the FIFO - there is no buffering in the DMA controller.
- * XXXX Do I read this right? It is from host to ESP, right?
- */
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- /* I don't think there's any limit on the CyberDMA. So we use what
- * the ESP chip can handle (24 bit).
- */
- unsigned long sz = sp->SCp.this_residual;
- if(sz > 0x1000000)
- sz = 0x1000000;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- ESPLOG(("esp%d: dma -- cond_reg<%02x>\n",
- esp->esp_id, ((struct cyber_dma_registers *)
- (esp->dregs))->cond_reg));
- ESPLOG(("intreq:<%04x>, intena:<%04x>\n",
- amiga_custom.intreqr, amiga_custom.intenar));
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct cyber_dma_registers *dregs =
- (struct cyber_dma_registers *) esp->dregs;
-
- cache_clear(addr, length);
-
- addr &= ~(1);
- dregs->dma_addr0 = (addr >> 24) & 0xff;
- dregs->dma_addr1 = (addr >> 16) & 0xff;
- dregs->dma_addr2 = (addr >> 8) & 0xff;
- dregs->dma_addr3 = (addr ) & 0xff;
- ctrl_data &= ~(CYBER_DMA_WRITE);
-
- /* Check if physical address is outside Z2 space and of
- * block length/block aligned in memory. If this is the
- * case, enable 32 bit transfer. In all other cases, fall back
- * to 16 bit transfer.
- * Obviously 32 bit transfer should be enabled if the DMA address
- * and length are 32 bit aligned. However, this leads to some
- * strange behavior. Even 64 bit aligned addr/length fails.
- * Until I've found a reason for this, 32 bit transfer is only
- * used for full-block transfers (1kB).
- * -jskov
- */
-#if 0
- if((addr & 0x3fc) || length & 0x3ff || ((addr > 0x200000) &&
- (addr < 0xff0000)))
- ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */
- else
- ctrl_data |= CYBER_DMA_Z3; /* CHIP/Z3, do 32 bit DMA */
-#else
- ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */
-#endif
- dregs->ctrl_reg = ctrl_data;
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct cyber_dma_registers *dregs =
- (struct cyber_dma_registers *) esp->dregs;
-
- cache_push(addr, length);
-
- addr |= 1;
- dregs->dma_addr0 = (addr >> 24) & 0xff;
- dregs->dma_addr1 = (addr >> 16) & 0xff;
- dregs->dma_addr2 = (addr >> 8) & 0xff;
- dregs->dma_addr3 = (addr ) & 0xff;
- ctrl_data |= CYBER_DMA_WRITE;
-
- /* See comment above */
-#if 0
- if((addr & 0x3fc) || length & 0x3ff || ((addr > 0x200000) &&
- (addr < 0xff0000)))
- ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */
- else
- ctrl_data |= CYBER_DMA_Z3; /* CHIP/Z3, do 32 bit DMA */
-#else
- ctrl_data &= ~(CYBER_DMA_Z3); /* Z2, do 16 bit DMA */
-#endif
- dregs->ctrl_reg = ctrl_data;
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(esp->irq);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(esp->irq);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- /* It's important to check the DMA IRQ bit in the correct way! */
- return ((esp_read(esp->eregs->esp_status) & ESP_STAT_INTR) &&
- ((((struct cyber_dma_registers *)(esp->dregs))->cond_reg) &
- CYBER_DMA_HNDL_INTR));
-}
-
-static void dma_led_off(struct NCR_ESP *esp)
-{
- ctrl_data &= ~CYBER_DMA_LED;
- ((struct cyber_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data;
-}
-
-static void dma_led_on(struct NCR_ESP *esp)
-{
- ctrl_data |= CYBER_DMA_LED;
- ((struct cyber_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data;
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return ((amiga_custom.intenar) & IF_PORTS);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if(write){
- dma_init_read(esp, addr, count);
- } else {
- dma_init_write(esp, addr, count);
- }
-}
-
-#define HOSTS_C
-
-int cyber_esp_release(struct Scsi_Host *instance)
-{
-#ifdef MODULE
- unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
-
- esp_deallocate((struct NCR_ESP *)instance->hostdata);
- esp_release();
- release_mem_region(address, sizeof(struct ESP_regs));
- free_irq(IRQ_AMIGA_PORTS, esp_intr);
-#endif
- return 1;
-}
-
-
-static struct scsi_host_template driver_template = {
- .proc_name = "esp-cyberstorm",
- .proc_info = esp_proc_info,
- .name = "CyberStorm SCSI",
- .detect = cyber_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = cyber_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/cyberstormII.c b/drivers/scsi/cyberstormII.c
deleted file mode 100644
index e336e85..0000000
--- a/drivers/scsi/cyberstormII.c
+++ /dev/null
@@ -1,314 +0,0 @@
-/* cyberstormII.c: Driver for CyberStorm SCSI Mk II
- *
- * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
- *
- * This driver is based on cyberstorm.c
- */
-
-/* TODO:
- *
- * 1) Figure out how to make a cleaner merge with the sparc driver with regard
- * to the caches and the Sparc MMU mapping.
- * 2) Make as few routines required outside the generic driver. A lot of the
- * routines in this file used to be inline!
- */
-
-#include <linux/module.h>
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <linux/zorro.h>
-#include <asm/irq.h>
-#include <asm/amigaints.h>
-#include <asm/amigahw.h>
-
-#include <asm/pgtable.h>
-
-/* The controller registers can be found in the Z2 config area at these
- * offsets:
- */
-#define CYBERII_ESP_ADDR 0x1ff03
-#define CYBERII_DMA_ADDR 0x1ff43
-
-
-/* The CyberStorm II DMA interface */
-struct cyberII_dma_registers {
- volatile unsigned char cond_reg; /* DMA cond (ro) [0x000] */
-#define ctrl_reg cond_reg /* DMA control (wo) [0x000] */
- unsigned char dmapad4[0x3f];
- volatile unsigned char dma_addr0; /* DMA address (MSB) [0x040] */
- unsigned char dmapad1[3];
- volatile unsigned char dma_addr1; /* DMA address [0x044] */
- unsigned char dmapad2[3];
- volatile unsigned char dma_addr2; /* DMA address [0x048] */
- unsigned char dmapad3[3];
- volatile unsigned char dma_addr3; /* DMA address (LSB) [0x04c] */
-};
-
-/* DMA control bits */
-#define CYBERII_DMA_LED 0x02 /* HD led control 1 = on */
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static void dma_led_off(struct NCR_ESP *esp);
-static void dma_led_on(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are transferred to the ESP chip
- * via PIO.
- */
-
-/***************************************************************** Detection */
-int __init cyberII_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct zorro_dev *z = NULL;
- unsigned long address;
- struct ESP_regs *eregs;
-
- if ((z = zorro_find_device(ZORRO_PROD_PHASE5_CYBERSTORM_MK_II, z))) {
- unsigned long board = z->resource.start;
- if (request_mem_region(board+CYBERII_ESP_ADDR,
- sizeof(struct ESP_regs), "NCR53C9x")) {
- /* Do some magic to figure out if the CyberStorm Mk II
- * is equipped with a SCSI controller
- */
- address = (unsigned long)ZTWO_VADDR(board);
- eregs = (struct ESP_regs *)(address + CYBERII_ESP_ADDR);
-
- esp = esp_allocate(tpnt, (void *)board + CYBERII_ESP_ADDR, 0);
-
- esp_write(eregs->esp_cfg1, (ESP_CONFIG1_PENABLE | 7));
- udelay(5);
- if(esp_read(eregs->esp_cfg1) != (ESP_CONFIG1_PENABLE | 7)) {
- esp_deallocate(esp);
- scsi_unregister(esp->ehost);
- release_mem_region(board+CYBERII_ESP_ADDR,
- sizeof(struct ESP_regs));
- return 0; /* Bail out if address did not hold data */
- }
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = 0;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_led_on = &dma_led_on;
- esp->dma_led_off = &dma_led_off;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
-
- /* SCSI chip speed */
- esp->cfreq = 40000000;
-
- /* The DMA registers on the CyberStorm are mapped
- * relative to the device (i.e. in the same Zorro
- * I/O block).
- */
- esp->dregs = (void *)(address + CYBERII_DMA_ADDR);
-
- /* ESP register base */
- esp->eregs = eregs;
-
- /* Set the command buffer */
- esp->esp_command = cmd_buffer;
- esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer);
-
- esp->irq = IRQ_AMIGA_PORTS;
- request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
- "CyberStorm SCSI Mk II", esp->ehost);
-
- /* Figure out our scsi ID on the bus */
- esp->scsi_id = 7;
-
- /* We don't have a differential SCSI-bus. */
- esp->diff = 0;
-
- esp_initialize(esp);
-
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use);
- esps_running = esps_in_use;
- return esps_in_use;
- }
- }
- return 0;
-}
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Since the CyberStorm DMA is fully dedicated to the ESP chip,
- * the number of bytes sent (to the ESP chip) equals the number
- * of bytes in the FIFO - there is no buffering in the DMA controller.
- * XXXX Do I read this right? It is from host to ESP, right?
- */
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- /* I don't think there's any limit on the CyberDMA. So we use what
- * the ESP chip can handle (24 bit).
- */
- unsigned long sz = sp->SCp.this_residual;
- if(sz > 0x1000000)
- sz = 0x1000000;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- ESPLOG(("esp%d: dma -- cond_reg<%02x>\n",
- esp->esp_id, ((struct cyberII_dma_registers *)
- (esp->dregs))->cond_reg));
- ESPLOG(("intreq:<%04x>, intena:<%04x>\n",
- amiga_custom.intreqr, amiga_custom.intenar));
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct cyberII_dma_registers *dregs =
- (struct cyberII_dma_registers *) esp->dregs;
-
- cache_clear(addr, length);
-
- addr &= ~(1);
- dregs->dma_addr0 = (addr >> 24) & 0xff;
- dregs->dma_addr1 = (addr >> 16) & 0xff;
- dregs->dma_addr2 = (addr >> 8) & 0xff;
- dregs->dma_addr3 = (addr ) & 0xff;
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct cyberII_dma_registers *dregs =
- (struct cyberII_dma_registers *) esp->dregs;
-
- cache_push(addr, length);
-
- addr |= 1;
- dregs->dma_addr0 = (addr >> 24) & 0xff;
- dregs->dma_addr1 = (addr >> 16) & 0xff;
- dregs->dma_addr2 = (addr >> 8) & 0xff;
- dregs->dma_addr3 = (addr ) & 0xff;
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(esp->irq);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(esp->irq);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- /* It's important to check the DMA IRQ bit in the correct way! */
- return (esp_read(esp->eregs->esp_status) & ESP_STAT_INTR);
-}
-
-static void dma_led_off(struct NCR_ESP *esp)
-{
- ((struct cyberII_dma_registers *)(esp->dregs))->ctrl_reg &= ~CYBERII_DMA_LED;
-}
-
-static void dma_led_on(struct NCR_ESP *esp)
-{
- ((struct cyberII_dma_registers *)(esp->dregs))->ctrl_reg |= CYBERII_DMA_LED;
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return ((amiga_custom.intenar) & IF_PORTS);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if(write){
- dma_init_read(esp, addr, count);
- } else {
- dma_init_write(esp, addr, count);
- }
-}
-
-#define HOSTS_C
-
-int cyberII_esp_release(struct Scsi_Host *instance)
-{
-#ifdef MODULE
- unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
-
- esp_deallocate((struct NCR_ESP *)instance->hostdata);
- esp_release();
- release_mem_region(address, sizeof(struct ESP_regs));
- free_irq(IRQ_AMIGA_PORTS, esp_intr);
-#endif
- return 1;
-}
-
-
-static struct scsi_host_template driver_template = {
- .proc_name = "esp-cyberstormII",
- .proc_info = esp_proc_info,
- .name = "CyberStorm Mk II SCSI",
- .detect = cyberII_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = cyberII_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/dec_esp.c b/drivers/scsi/dec_esp.c
deleted file mode 100644
index d42ad66..0000000
--- a/drivers/scsi/dec_esp.c
+++ /dev/null
@@ -1,687 +0,0 @@
-/*
- * dec_esp.c: Driver for SCSI chips on IOASIC based TURBOchannel DECstations
- * and TURBOchannel PMAZ-A cards
- *
- * TURBOchannel changes by Harald Koerfgen
- * PMAZ-A support by David Airlie
- *
- * based on jazz_esp.c:
- * Copyright (C) 1997 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
- *
- * jazz_esp is based on David S. Miller's ESP driver and cyber_esp
- *
- * 20000819 - Small PMAZ-AA fixes by Florian Lohoff <flo@rfc822.org>
- * Be warned the PMAZ-AA works currently as a single card.
- * Dont try to put multiple cards in one machine - They are
- * both detected but it may crash under high load garbling your
- * data.
- * 20001005 - Initialization fixes for 2.4.0-test9
- * Florian Lohoff <flo@rfc822.org>
- *
- * Copyright (C) 2002, 2003, 2005, 2006 Maciej W. Rozycki
- */
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/spinlock.h>
-#include <linux/stat.h>
-#include <linux/tc.h>
-
-#include <asm/dma.h>
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/system.h>
-
-#include <asm/dec/interrupts.h>
-#include <asm/dec/ioasic.h>
-#include <asm/dec/ioasic_addrs.h>
-#include <asm/dec/ioasic_ints.h>
-#include <asm/dec/machtype.h>
-#include <asm/dec/system.h>
-
-#define DEC_SCSI_SREG 0
-#define DEC_SCSI_DMAREG 0x40000
-#define DEC_SCSI_SRAM 0x80000
-#define DEC_SCSI_DIAG 0xC0000
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static void dma_drain(struct NCR_ESP *esp);
-static int dma_can_transfer(struct NCR_ESP *esp, struct scsi_cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, u32 vaddress, int length);
-static void dma_init_write(struct NCR_ESP *esp, u32 vaddress, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, u32 addr, int count, int write);
-static void dma_mmu_get_scsi_one(struct NCR_ESP *esp, struct scsi_cmnd * sp);
-static void dma_mmu_get_scsi_sgl(struct NCR_ESP *esp, struct scsi_cmnd * sp);
-static void dma_advance_sg(struct scsi_cmnd * sp);
-
-static void pmaz_dma_drain(struct NCR_ESP *esp);
-static void pmaz_dma_init_read(struct NCR_ESP *esp, u32 vaddress, int length);
-static void pmaz_dma_init_write(struct NCR_ESP *esp, u32 vaddress, int length);
-static void pmaz_dma_ints_off(struct NCR_ESP *esp);
-static void pmaz_dma_ints_on(struct NCR_ESP *esp);
-static void pmaz_dma_setup(struct NCR_ESP *esp, u32 addr, int count, int write);
-static void pmaz_dma_mmu_get_scsi_one(struct NCR_ESP *esp, struct scsi_cmnd * sp);
-
-#define TC_ESP_RAM_SIZE 0x20000
-#define ESP_TGT_DMA_SIZE ((TC_ESP_RAM_SIZE/7) & ~(sizeof(int)-1))
-#define ESP_NCMD 7
-
-#define TC_ESP_DMAR_MASK 0x1ffff
-#define TC_ESP_DMAR_WRITE 0x80000000
-#define TC_ESP_DMA_ADDR(x) ((unsigned)(x) & TC_ESP_DMAR_MASK)
-
-u32 esp_virt_buffer;
-int scsi_current_length;
-
-volatile unsigned char cmd_buffer[16];
-volatile unsigned char pmaz_cmd_buffer[16];
- /* This is where all commands are put
- * before they are trasfered to the ESP chip
- * via PIO.
- */
-
-static irqreturn_t scsi_dma_merr_int(int, void *);
-static irqreturn_t scsi_dma_err_int(int, void *);
-static irqreturn_t scsi_dma_int(int, void *);
-
-static struct scsi_host_template dec_esp_template = {
- .module = THIS_MODULE,
- .name = "NCR53C94",
- .info = esp_info,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .proc_info = esp_proc_info,
- .proc_name = "dec_esp",
- .can_queue = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = DISABLE_CLUSTERING,
-};
-
-static struct NCR_ESP *dec_esp_platform;
-
-/***************************************************************** Detection */
-static int dec_esp_platform_probe(void)
-{
- struct NCR_ESP *esp;
- int err = 0;
-
- if (IOASIC) {
- esp = esp_allocate(&dec_esp_template, NULL, 1);
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = &dma_drain;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
- esp->dma_led_off = 0;
- esp->dma_led_on = 0;
-
- /* virtual DMA functions */
- esp->dma_mmu_get_scsi_one = &dma_mmu_get_scsi_one;
- esp->dma_mmu_get_scsi_sgl = &dma_mmu_get_scsi_sgl;
- esp->dma_mmu_release_scsi_one = 0;
- esp->dma_mmu_release_scsi_sgl = 0;
- esp->dma_advance_sg = &dma_advance_sg;
-
-
- /* SCSI chip speed */
- esp->cfreq = 25000000;
-
- esp->dregs = 0;
-
- /* ESP register base */
- esp->eregs = (void *)CKSEG1ADDR(dec_kn_slot_base +
- IOASIC_SCSI);
-
- /* Set the command buffer */
- esp->esp_command = (volatile unsigned char *) cmd_buffer;
-
- /* get virtual dma address for command buffer */
- esp->esp_command_dvma = virt_to_phys(cmd_buffer);
-
- esp->irq = dec_interrupt[DEC_IRQ_ASC];
-
- esp->scsi_id = 7;
-
- /* Check for differential SCSI-bus */
- esp->diff = 0;
-
- err = request_irq(esp->irq, esp_intr, IRQF_DISABLED,
- "ncr53c94", esp->ehost);
- if (err)
- goto err_alloc;
- err = request_irq(dec_interrupt[DEC_IRQ_ASC_MERR],
- scsi_dma_merr_int, IRQF_DISABLED,
- "ncr53c94 error", esp->ehost);
- if (err)
- goto err_irq;
- err = request_irq(dec_interrupt[DEC_IRQ_ASC_ERR],
- scsi_dma_err_int, IRQF_DISABLED,
- "ncr53c94 overrun", esp->ehost);
- if (err)
- goto err_irq_merr;
- err = request_irq(dec_interrupt[DEC_IRQ_ASC_DMA], scsi_dma_int,
- IRQF_DISABLED, "ncr53c94 dma", esp->ehost);
- if (err)
- goto err_irq_err;
-
- esp_initialize(esp);
-
- err = scsi_add_host(esp->ehost, NULL);
- if (err) {
- printk(KERN_ERR "ESP: Unable to register adapter\n");
- goto err_irq_dma;
- }
-
- scsi_scan_host(esp->ehost);
-
- dec_esp_platform = esp;
- }
-
- return 0;
-
-err_irq_dma:
- free_irq(dec_interrupt[DEC_IRQ_ASC_DMA], esp->ehost);
-err_irq_err:
- free_irq(dec_interrupt[DEC_IRQ_ASC_ERR], esp->ehost);
-err_irq_merr:
- free_irq(dec_interrupt[DEC_IRQ_ASC_MERR], esp->ehost);
-err_irq:
- free_irq(esp->irq, esp->ehost);
-err_alloc:
- esp_deallocate(esp);
- scsi_host_put(esp->ehost);
- return err;
-}
-
-static int __init dec_esp_probe(struct device *dev)
-{
- struct NCR_ESP *esp;
- resource_size_t start, len;
- int err;
-
- esp = esp_allocate(&dec_esp_template, NULL, 1);
-
- dev_set_drvdata(dev, esp);
-
- start = to_tc_dev(dev)->resource.start;
- len = to_tc_dev(dev)->resource.end - start + 1;
-
- if (!request_mem_region(start, len, dev->bus_id)) {
- printk(KERN_ERR "%s: Unable to reserve MMIO resource\n",
- dev->bus_id);
- err = -EBUSY;
- goto err_alloc;
- }
-
- /* Store base addr into esp struct. */
- esp->slot = start;
-
- esp->dregs = 0;
- esp->eregs = (void *)CKSEG1ADDR(start + DEC_SCSI_SREG);
- esp->do_pio_cmds = 1;
-
- /* Set the command buffer. */
- esp->esp_command = (volatile unsigned char *)pmaz_cmd_buffer;
-
- /* Get virtual dma address for command buffer. */
- esp->esp_command_dvma = virt_to_phys(pmaz_cmd_buffer);
-
- esp->cfreq = tc_get_speed(to_tc_dev(dev)->bus);
-
- esp->irq = to_tc_dev(dev)->interrupt;
-
- /* Required functions. */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &pmaz_dma_init_read;
- esp->dma_init_write = &pmaz_dma_init_write;
- esp->dma_ints_off = &pmaz_dma_ints_off;
- esp->dma_ints_on = &pmaz_dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &pmaz_dma_setup;
-
- /* Optional functions. */
- esp->dma_barrier = 0;
- esp->dma_drain = &pmaz_dma_drain;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
- esp->dma_led_off = 0;
- esp->dma_led_on = 0;
-
- esp->dma_mmu_get_scsi_one = pmaz_dma_mmu_get_scsi_one;
- esp->dma_mmu_get_scsi_sgl = 0;
- esp->dma_mmu_release_scsi_one = 0;
- esp->dma_mmu_release_scsi_sgl = 0;
- esp->dma_advance_sg = 0;
-
- err = request_irq(esp->irq, esp_intr, IRQF_DISABLED, "PMAZ_AA",
- esp->ehost);
- if (err) {
- printk(KERN_ERR "%s: Unable to get IRQ %d\n",
- dev->bus_id, esp->irq);
- goto err_resource;
- }
-
- esp->scsi_id = 7;
- esp->diff = 0;
- esp_initialize(esp);
-
- err = scsi_add_host(esp->ehost, dev);
- if (err) {
- printk(KERN_ERR "%s: Unable to register adapter\n",
- dev->bus_id);
- goto err_irq;
- }
-
- scsi_scan_host(esp->ehost);
-
- return 0;
-
-err_irq:
- free_irq(esp->irq, esp->ehost);
-
-err_resource:
- release_mem_region(start, len);
-
-err_alloc:
- esp_deallocate(esp);
- scsi_host_put(esp->ehost);
- return err;
-}
-
-static void __exit dec_esp_platform_remove(void)
-{
- struct NCR_ESP *esp = dec_esp_platform;
-
- free_irq(esp->irq, esp->ehost);
- esp_deallocate(esp);
- scsi_host_put(esp->ehost);
- dec_esp_platform = NULL;
-}
-
-static void __exit dec_esp_remove(struct device *dev)
-{
- struct NCR_ESP *esp = dev_get_drvdata(dev);
-
- free_irq(esp->irq, esp->ehost);
- esp_deallocate(esp);
- scsi_host_put(esp->ehost);
-}
-
-
-/************************************************************* DMA Functions */
-static irqreturn_t scsi_dma_merr_int(int irq, void *dev_id)
-{
- printk("Got unexpected SCSI DMA Interrupt! < ");
- printk("SCSI_DMA_MEMRDERR ");
- printk(">\n");
-
- return IRQ_HANDLED;
-}
-
-static irqreturn_t scsi_dma_err_int(int irq, void *dev_id)
-{
- /* empty */
-
- return IRQ_HANDLED;
-}
-
-static irqreturn_t scsi_dma_int(int irq, void *dev_id)
-{
- u32 scsi_next_ptr;
-
- scsi_next_ptr = ioasic_read(IO_REG_SCSI_DMA_P);
-
- /* next page */
- scsi_next_ptr = (((scsi_next_ptr >> 3) + PAGE_SIZE) & PAGE_MASK) << 3;
- ioasic_write(IO_REG_SCSI_DMA_BP, scsi_next_ptr);
- fast_iob();
-
- return IRQ_HANDLED;
-}
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- return fifo_count;
-}
-
-static void dma_drain(struct NCR_ESP *esp)
-{
- u32 nw, data0, data1, scsi_data_ptr;
- u16 *p;
-
- nw = ioasic_read(IO_REG_SCSI_SCR);
-
- /*
- * Is there something in the dma buffers left?
- */
- if (nw) {
- scsi_data_ptr = ioasic_read(IO_REG_SCSI_DMA_P) >> 3;
- p = phys_to_virt(scsi_data_ptr);
- switch (nw) {
- case 1:
- data0 = ioasic_read(IO_REG_SCSI_SDR0);
- p[0] = data0 & 0xffff;
- break;
- case 2:
- data0 = ioasic_read(IO_REG_SCSI_SDR0);
- p[0] = data0 & 0xffff;
- p[1] = (data0 >> 16) & 0xffff;
- break;
- case 3:
- data0 = ioasic_read(IO_REG_SCSI_SDR0);
- data1 = ioasic_read(IO_REG_SCSI_SDR1);
- p[0] = data0 & 0xffff;
- p[1] = (data0 >> 16) & 0xffff;
- p[2] = data1 & 0xffff;
- break;
- default:
- printk("Strange: %d words in dma buffer left\n", nw);
- break;
- }
- }
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, struct scsi_cmnd * sp)
-{
- return sp->SCp.this_residual;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
-}
-
-static void dma_init_read(struct NCR_ESP *esp, u32 vaddress, int length)
-{
- u32 scsi_next_ptr, ioasic_ssr;
- unsigned long flags;
-
- if (vaddress & 3)
- panic("dec_esp.c: unable to handle partial word transfers, yet...");
-
- dma_cache_wback_inv((unsigned long) phys_to_virt(vaddress), length);
-
- spin_lock_irqsave(&ioasic_ssr_lock, flags);
-
- fast_mb();
- ioasic_ssr = ioasic_read(IO_REG_SSR);
-
- ioasic_ssr &= ~IO_SSR_SCSI_DMA_EN;
- ioasic_write(IO_REG_SSR, ioasic_ssr);
-
- fast_wmb();
- ioasic_write(IO_REG_SCSI_SCR, 0);
- ioasic_write(IO_REG_SCSI_DMA_P, vaddress << 3);
-
- /* prepare for next page */
- scsi_next_ptr = ((vaddress + PAGE_SIZE) & PAGE_MASK) << 3;
- ioasic_write(IO_REG_SCSI_DMA_BP, scsi_next_ptr);
-
- ioasic_ssr |= (IO_SSR_SCSI_DMA_DIR | IO_SSR_SCSI_DMA_EN);
- fast_wmb();
- ioasic_write(IO_REG_SSR, ioasic_ssr);
-
- fast_iob();
- spin_unlock_irqrestore(&ioasic_ssr_lock, flags);
-}
-
-static void dma_init_write(struct NCR_ESP *esp, u32 vaddress, int length)
-{
- u32 scsi_next_ptr, ioasic_ssr;
- unsigned long flags;
-
- if (vaddress & 3)
- panic("dec_esp.c: unable to handle partial word transfers, yet...");
-
- dma_cache_wback_inv((unsigned long) phys_to_virt(vaddress), length);
-
- spin_lock_irqsave(&ioasic_ssr_lock, flags);
-
- fast_mb();
- ioasic_ssr = ioasic_read(IO_REG_SSR);
-
- ioasic_ssr &= ~(IO_SSR_SCSI_DMA_DIR | IO_SSR_SCSI_DMA_EN);
- ioasic_write(IO_REG_SSR, ioasic_ssr);
-
- fast_wmb();
- ioasic_write(IO_REG_SCSI_SCR, 0);
- ioasic_write(IO_REG_SCSI_DMA_P, vaddress << 3);
-
- /* prepare for next page */
- scsi_next_ptr = ((vaddress + PAGE_SIZE) & PAGE_MASK) << 3;
- ioasic_write(IO_REG_SCSI_DMA_BP, scsi_next_ptr);
-
- ioasic_ssr |= IO_SSR_SCSI_DMA_EN;
- fast_wmb();
- ioasic_write(IO_REG_SSR, ioasic_ssr);
-
- fast_iob();
- spin_unlock_irqrestore(&ioasic_ssr_lock, flags);
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(dec_interrupt[DEC_IRQ_ASC_DMA]);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(dec_interrupt[DEC_IRQ_ASC_DMA]);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- return (esp->eregs->esp_status & ESP_STAT_INTR);
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- /*
- * FIXME: what's this good for?
- */
- return 1;
-}
-
-static void dma_setup(struct NCR_ESP *esp, u32 addr, int count, int write)
-{
- /*
- * DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if (write)
- dma_init_read(esp, addr, count);
- else
- dma_init_write(esp, addr, count);
-}
-
-static void dma_mmu_get_scsi_one(struct NCR_ESP *esp, struct scsi_cmnd * sp)
-{
- sp->SCp.ptr = (char *)virt_to_phys(sp->request_buffer);
-}
-
-static void dma_mmu_get_scsi_sgl(struct NCR_ESP *esp, struct scsi_cmnd * sp)
-{
- int sz = sp->SCp.buffers_residual;
- struct scatterlist *sg = sp->SCp.buffer;
-
- while (sz >= 0) {
- sg[sz].dma_address = page_to_phys(sg[sz].page) + sg[sz].offset;
- sz--;
- }
- sp->SCp.ptr = (char *)(sp->SCp.buffer->dma_address);
-}
-
-static void dma_advance_sg(struct scsi_cmnd * sp)
-{
- sp->SCp.ptr = (char *)(sp->SCp.buffer->dma_address);
-}
-
-static void pmaz_dma_drain(struct NCR_ESP *esp)
-{
- memcpy(phys_to_virt(esp_virt_buffer),
- (void *)CKSEG1ADDR(esp->slot + DEC_SCSI_SRAM +
- ESP_TGT_DMA_SIZE),
- scsi_current_length);
-}
-
-static void pmaz_dma_init_read(struct NCR_ESP *esp, u32 vaddress, int length)
-{
- volatile u32 *dmareg =
- (volatile u32 *)CKSEG1ADDR(esp->slot + DEC_SCSI_DMAREG);
-
- if (length > ESP_TGT_DMA_SIZE)
- length = ESP_TGT_DMA_SIZE;
-
- *dmareg = TC_ESP_DMA_ADDR(ESP_TGT_DMA_SIZE);
-
- iob();
-
- esp_virt_buffer = vaddress;
- scsi_current_length = length;
-}
-
-static void pmaz_dma_init_write(struct NCR_ESP *esp, u32 vaddress, int length)
-{
- volatile u32 *dmareg =
- (volatile u32 *)CKSEG1ADDR(esp->slot + DEC_SCSI_DMAREG);
-
- memcpy((void *)CKSEG1ADDR(esp->slot + DEC_SCSI_SRAM +
- ESP_TGT_DMA_SIZE),
- phys_to_virt(vaddress), length);
-
- wmb();
- *dmareg = TC_ESP_DMAR_WRITE | TC_ESP_DMA_ADDR(ESP_TGT_DMA_SIZE);
-
- iob();
-}
-
-static void pmaz_dma_ints_off(struct NCR_ESP *esp)
-{
-}
-
-static void pmaz_dma_ints_on(struct NCR_ESP *esp)
-{
-}
-
-static void pmaz_dma_setup(struct NCR_ESP *esp, u32 addr, int count, int write)
-{
- /*
- * DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if (write)
- pmaz_dma_init_read(esp, addr, count);
- else
- pmaz_dma_init_write(esp, addr, count);
-}
-
-static void pmaz_dma_mmu_get_scsi_one(struct NCR_ESP *esp, struct scsi_cmnd * sp)
-{
- sp->SCp.ptr = (char *)virt_to_phys(sp->request_buffer);
-}
-
-
-#ifdef CONFIG_TC
-static int __init dec_esp_tc_probe(struct device *dev);
-static int __exit dec_esp_tc_remove(struct device *dev);
-
-static const struct tc_device_id dec_esp_tc_table[] = {
- { "DEC ", "PMAZ-AA " },
- { }
-};
-MODULE_DEVICE_TABLE(tc, dec_esp_tc_table);
-
-static struct tc_driver dec_esp_tc_driver = {
- .id_table = dec_esp_tc_table,
- .driver = {
- .name = "dec_esp",
- .bus = &tc_bus_type,
- .probe = dec_esp_tc_probe,
- .remove = __exit_p(dec_esp_tc_remove),
- },
-};
-
-static int __init dec_esp_tc_probe(struct device *dev)
-{
- int status = dec_esp_probe(dev);
- if (!status)
- get_device(dev);
- return status;
-}
-
-static int __exit dec_esp_tc_remove(struct device *dev)
-{
- put_device(dev);
- dec_esp_remove(dev);
- return 0;
-}
-#endif
-
-static int __init dec_esp_init(void)
-{
- int status;
-
- status = tc_register_driver(&dec_esp_tc_driver);
- if (!status)
- dec_esp_platform_probe();
-
- if (nesps) {
- pr_info("ESP: Total of %d ESP hosts found, "
- "%d actually in use.\n", nesps, esps_in_use);
- esps_running = esps_in_use;
- }
-
- return status;
-}
-
-static void __exit dec_esp_exit(void)
-{
- dec_esp_platform_remove();
- tc_unregister_driver(&dec_esp_tc_driver);
-}
-
-
-module_init(dec_esp_init);
-module_exit(dec_esp_exit);
diff --git a/drivers/scsi/fastlane.c b/drivers/scsi/fastlane.c
deleted file mode 100644
index 4266a21..0000000
--- a/drivers/scsi/fastlane.c
+++ /dev/null
@@ -1,421 +0,0 @@
-/* fastlane.c: Driver for Phase5's Fastlane SCSI Controller.
- *
- * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
- *
- * This driver is based on the CyberStorm driver, hence the occasional
- * reference to CyberStorm.
- *
- * Betatesting & crucial adjustments by
- * Patrik Rak (prak3264@ss1000.ms.mff.cuni.cz)
- *
- */
-
-/* TODO:
- *
- * o According to the doc from laire, it is required to reset the DMA when
- * the transfer is done. ATM we reset DMA just before every new
- * dma_init_(read|write).
- *
- * 1) Figure out how to make a cleaner merge with the sparc driver with regard
- * to the caches and the Sparc MMU mapping.
- * 2) Make as few routines required outside the generic driver. A lot of the
- * routines in this file used to be inline!
- */
-
-#include <linux/module.h>
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <linux/zorro.h>
-#include <asm/irq.h>
-
-#include <asm/amigaints.h>
-#include <asm/amigahw.h>
-
-#include <asm/pgtable.h>
-
-/* Such day has just come... */
-#if 0
-/* Let this defined unless you really need to enable DMA IRQ one day */
-#define NODMAIRQ
-#endif
-
-/* The controller registers can be found in the Z2 config area at these
- * offsets:
- */
-#define FASTLANE_ESP_ADDR 0x1000001
-#define FASTLANE_DMA_ADDR 0x1000041
-
-
-/* The Fastlane DMA interface */
-struct fastlane_dma_registers {
- volatile unsigned char cond_reg; /* DMA status (ro) [0x0000] */
-#define ctrl_reg cond_reg /* DMA control (wo) [0x0000] */
- unsigned char dmapad1[0x3f];
- volatile unsigned char clear_strobe; /* DMA clear (wo) [0x0040] */
-};
-
-
-/* DMA status bits */
-#define FASTLANE_DMA_MINT 0x80
-#define FASTLANE_DMA_IACT 0x40
-#define FASTLANE_DMA_CREQ 0x20
-
-/* DMA control bits */
-#define FASTLANE_DMA_FCODE 0xa0
-#define FASTLANE_DMA_MASK 0xf3
-#define FASTLANE_DMA_LED 0x10 /* HD led control 1 = on */
-#define FASTLANE_DMA_WRITE 0x08 /* 1 = write */
-#define FASTLANE_DMA_ENABLE 0x04 /* Enable DMA */
-#define FASTLANE_DMA_EDI 0x02 /* Enable DMA IRQ ? */
-#define FASTLANE_DMA_ESI 0x01 /* Enable SCSI IRQ */
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 vaddr, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static void dma_irq_exit(struct NCR_ESP *esp);
-static void dma_led_off(struct NCR_ESP *esp);
-static void dma_led_on(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-
-static unsigned char ctrl_data = 0; /* Keep backup of the stuff written
- * to ctrl_reg. Always write a copy
- * to this register when writing to
- * the hardware register!
- */
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are transferred to the ESP chip
- * via PIO.
- */
-
-static inline void dma_clear(struct NCR_ESP *esp)
-{
- struct fastlane_dma_registers *dregs =
- (struct fastlane_dma_registers *) (esp->dregs);
- unsigned long *t;
-
- ctrl_data = (ctrl_data & FASTLANE_DMA_MASK);
- dregs->ctrl_reg = ctrl_data;
-
- t = (unsigned long *)(esp->edev);
-
- dregs->clear_strobe = 0;
- *t = 0 ;
-}
-
-/***************************************************************** Detection */
-int __init fastlane_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct zorro_dev *z = NULL;
- unsigned long address;
-
- if ((z = zorro_find_device(ZORRO_PROD_PHASE5_BLIZZARD_1230_II_FASTLANE_Z3_CYBERSCSI_CYBERSTORM060, z))) {
- unsigned long board = z->resource.start;
- if (request_mem_region(board+FASTLANE_ESP_ADDR,
- sizeof(struct ESP_regs), "NCR53C9x")) {
- /* Check if this is really a fastlane controller. The problem
- * is that also the cyberstorm and blizzard controllers use
- * this ID value. Fortunately only Fastlane maps in Z3 space
- */
- if (board < 0x1000000) {
- goto err_release;
- }
- esp = esp_allocate(tpnt, (void *)board + FASTLANE_ESP_ADDR, 0);
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = 0;
- esp->dma_invalidate = 0;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = &dma_irq_exit;
- esp->dma_led_on = &dma_led_on;
- esp->dma_led_off = &dma_led_off;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
-
- /* Initialize the portBits (enable IRQs) */
- ctrl_data = (FASTLANE_DMA_FCODE |
-#ifndef NODMAIRQ
- FASTLANE_DMA_EDI |
-#endif
- FASTLANE_DMA_ESI);
-
-
- /* SCSI chip clock */
- esp->cfreq = 40000000;
-
-
- /* Map the physical address space into virtual kernel space */
- address = (unsigned long)
- z_ioremap(board, z->resource.end-board+1);
-
- if(!address){
- printk("Could not remap Fastlane controller memory!");
- goto err_unregister;
- }
-
-
- /* The DMA registers on the Fastlane are mapped
- * relative to the device (i.e. in the same Zorro
- * I/O block).
- */
- esp->dregs = (void *)(address + FASTLANE_DMA_ADDR);
-
- /* ESP register base */
- esp->eregs = (struct ESP_regs *)(address + FASTLANE_ESP_ADDR);
-
- /* Board base */
- esp->edev = (void *) address;
-
- /* Set the command buffer */
- esp->esp_command = cmd_buffer;
- esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer);
-
- esp->irq = IRQ_AMIGA_PORTS;
- esp->slot = board+FASTLANE_ESP_ADDR;
- if (request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
- "Fastlane SCSI", esp->ehost)) {
- printk(KERN_WARNING "Fastlane: Could not get IRQ%d, aborting.\n", IRQ_AMIGA_PORTS);
- goto err_unmap;
- }
-
- /* Controller ID */
- esp->scsi_id = 7;
-
- /* We don't have a differential SCSI-bus. */
- esp->diff = 0;
-
- dma_clear(esp);
- esp_initialize(esp);
-
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use);
- esps_running = esps_in_use;
- return esps_in_use;
- }
- }
- return 0;
-
- err_unmap:
- z_iounmap((void *)address);
- err_unregister:
- scsi_unregister (esp->ehost);
- err_release:
- release_mem_region(z->resource.start+FASTLANE_ESP_ADDR,
- sizeof(struct ESP_regs));
- return 0;
-}
-
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Since the Fastlane DMA is fully dedicated to the ESP chip,
- * the number of bytes sent (to the ESP chip) equals the number
- * of bytes in the FIFO - there is no buffering in the DMA controller.
- * XXXX Do I read this right? It is from host to ESP, right?
- */
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- unsigned long sz = sp->SCp.this_residual;
- if(sz > 0xfffc)
- sz = 0xfffc;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- ESPLOG(("esp%d: dma -- cond_reg<%02x>\n",
- esp->esp_id, ((struct fastlane_dma_registers *)
- (esp->dregs))->cond_reg));
- ESPLOG(("intreq:<%04x>, intena:<%04x>\n",
- amiga_custom.intreqr, amiga_custom.intenar));
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct fastlane_dma_registers *dregs =
- (struct fastlane_dma_registers *) (esp->dregs);
- unsigned long *t;
-
- cache_clear(addr, length);
-
- dma_clear(esp);
-
- t = (unsigned long *)((addr & 0x00ffffff) + esp->edev);
-
- dregs->clear_strobe = 0;
- *t = addr;
-
- ctrl_data = (ctrl_data & FASTLANE_DMA_MASK) | FASTLANE_DMA_ENABLE;
- dregs->ctrl_reg = ctrl_data;
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
-{
- struct fastlane_dma_registers *dregs =
- (struct fastlane_dma_registers *) (esp->dregs);
- unsigned long *t;
-
- cache_push(addr, length);
-
- dma_clear(esp);
-
- t = (unsigned long *)((addr & 0x00ffffff) + (esp->edev));
-
- dregs->clear_strobe = 0;
- *t = addr;
-
- ctrl_data = ((ctrl_data & FASTLANE_DMA_MASK) |
- FASTLANE_DMA_ENABLE |
- FASTLANE_DMA_WRITE);
- dregs->ctrl_reg = ctrl_data;
-}
-
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(esp->irq);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(esp->irq);
-}
-
-static void dma_irq_exit(struct NCR_ESP *esp)
-{
- struct fastlane_dma_registers *dregs =
- (struct fastlane_dma_registers *) (esp->dregs);
-
- dregs->ctrl_reg = ctrl_data & ~(FASTLANE_DMA_EDI|FASTLANE_DMA_ESI);
-#ifdef __mc68000__
- nop();
-#endif
- dregs->ctrl_reg = ctrl_data;
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- struct fastlane_dma_registers *dregs =
- (struct fastlane_dma_registers *) (esp->dregs);
- unsigned char dma_status;
-
- dma_status = dregs->cond_reg;
-
- if(dma_status & FASTLANE_DMA_IACT)
- return 0; /* not our IRQ */
-
- /* Return non-zero if ESP requested IRQ */
- return (
-#ifndef NODMAIRQ
- (dma_status & FASTLANE_DMA_CREQ) &&
-#endif
- (!(dma_status & FASTLANE_DMA_MINT)) &&
- (esp_read(((struct ESP_regs *) (esp->eregs))->esp_status) & ESP_STAT_INTR));
-}
-
-static void dma_led_off(struct NCR_ESP *esp)
-{
- ctrl_data &= ~FASTLANE_DMA_LED;
- ((struct fastlane_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data;
-}
-
-static void dma_led_on(struct NCR_ESP *esp)
-{
- ctrl_data |= FASTLANE_DMA_LED;
- ((struct fastlane_dma_registers *)(esp->dregs))->ctrl_reg = ctrl_data;
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return ((amiga_custom.intenar) & IF_PORTS);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if(write){
- dma_init_read(esp, addr, count);
- } else {
- dma_init_write(esp, addr, count);
- }
-}
-
-#define HOSTS_C
-
-int fastlane_esp_release(struct Scsi_Host *instance)
-{
-#ifdef MODULE
- unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
- esp_deallocate((struct NCR_ESP *)instance->hostdata);
- esp_release();
- release_mem_region(address, sizeof(struct ESP_regs));
- free_irq(IRQ_AMIGA_PORTS, esp_intr);
-#endif
- return 1;
-}
-
-
-static struct scsi_host_template driver_template = {
- .proc_name = "esp-fastlane",
- .proc_info = esp_proc_info,
- .name = "Fastlane SCSI",
- .detect = fastlane_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = fastlane_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING
-};
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/mac_esp.c b/drivers/scsi/mac_esp.c
deleted file mode 100644
index bcb4902..0000000
--- a/drivers/scsi/mac_esp.c
+++ /dev/null
@@ -1,751 +0,0 @@
-/*
- * 68k mac 53c9[46] scsi driver
- *
- * copyright (c) 1998, David Weis weisd3458@uni.edu
- *
- * debugging on Quadra 800 and 660AV Michael Schmitz, Dave Kilzer 7/98
- *
- * based loosely on cyber_esp.c
- */
-
-/* these are unused for now */
-#define myreadl(addr) (*(volatile unsigned int *) (addr))
-#define mywritel(b, addr) ((*(volatile unsigned int *) (addr)) = (b))
-
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/ctype.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <asm/io.h>
-
-#include <asm/setup.h>
-#include <asm/irq.h>
-#include <asm/macints.h>
-#include <asm/machw.h>
-#include <asm/mac_via.h>
-
-#include <asm/pgtable.h>
-
-#include <asm/macintosh.h>
-
-/* #define DEBUG_MAC_ESP */
-
-extern void esp_handle(struct NCR_ESP *esp);
-extern void mac_esp_intr(int irq, void *dev_id);
-
-static int dma_bytes_sent(struct NCR_ESP * esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP * esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP * esp);
-static void dma_init_read(struct NCR_ESP * esp, char * vaddress, int length);
-static void dma_init_write(struct NCR_ESP * esp, char * vaddress, int length);
-static void dma_ints_off(struct NCR_ESP * esp);
-static void dma_ints_on(struct NCR_ESP * esp);
-static int dma_irq_p(struct NCR_ESP * esp);
-static int dma_irq_p_quick(struct NCR_ESP * esp);
-static void dma_led_off(struct NCR_ESP * esp);
-static void dma_led_on(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP * esp, __u32 addr, int count, int write);
-static void dma_setup_quick(struct NCR_ESP * esp, __u32 addr, int count, int write);
-
-static int esp_dafb_dma_irq_p(struct NCR_ESP * espdev);
-static int esp_iosb_dma_irq_p(struct NCR_ESP * espdev);
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are transferred to the ESP chip
- * via PIO.
- */
-
-static int esp_initialized = 0;
-
-static int setup_num_esps = -1;
-static int setup_disconnect = -1;
-static int setup_nosync = -1;
-static int setup_can_queue = -1;
-static int setup_cmd_per_lun = -1;
-static int setup_sg_tablesize = -1;
-#ifdef SUPPORT_TAGS
-static int setup_use_tagged_queuing = -1;
-#endif
-static int setup_hostid = -1;
-
-/*
- * Experimental ESP inthandler; check macints.c to make sure dev_id is
- * set up properly!
- */
-
-void mac_esp_intr(int irq, void *dev_id)
-{
- struct NCR_ESP *esp = (struct NCR_ESP *) dev_id;
- int irq_p = 0;
-
- /* Handle the one ESP interrupt showing at this IRQ level. */
- if(((esp)->irq & 0xff) == irq) {
- /*
- * Debug ..
- */
- irq_p = esp->dma_irq_p(esp);
- printk("mac_esp: irq_p %x current %p disconnected %p\n",
- irq_p, esp->current_SC, esp->disconnected_SC);
-
- /*
- * Mac: if we're here, it's an ESP interrupt for sure!
- */
- if((esp->current_SC || esp->disconnected_SC)) {
- esp->dma_ints_off(esp);
-
- ESPIRQ(("I%d(", esp->esp_id));
- esp_handle(esp);
- ESPIRQ((")"));
-
- esp->dma_ints_on(esp);
- }
- }
-}
-
-/*
- * Debug hooks; use for playing with the interrupt flag testing and interrupt
- * acknowledge on the various machines
- */
-
-void scsi_esp_polled(int irq, void *dev_id)
-{
- if (esp_initialized == 0)
- return;
-
- mac_esp_intr(irq, dev_id);
-}
-
-void fake_intr(int irq, void *dev_id)
-{
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: got irq\n");
-#endif
-
- mac_esp_intr(irq, dev_id);
-}
-
-irqreturn_t fake_drq(int irq, void *dev_id)
-{
- printk("mac_esp: got drq\n");
- return IRQ_HANDLED;
-}
-
-#define DRIVER_SETUP
-
-/*
- * Function : mac_esp_setup(char *str)
- *
- * Purpose : booter command line initialization of the overrides array,
- *
- * Inputs : str - parameters, separated by commas.
- *
- * Currently unused in the new driver; need to add settable parameters to the
- * detect function.
- *
- */
-
-static int __init mac_esp_setup(char *str) {
-#ifdef DRIVER_SETUP
- /* Format of mac53c9x parameter is:
- * mac53c9x=<num_esps>,<disconnect>,<nosync>,<can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
- * Negative values mean don't change.
- */
-
- char *this_opt;
- long opt;
-
- this_opt = strsep (&str, ",");
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- if (opt >= 0 && opt <= 2)
- setup_num_esps = opt;
- else if (opt > 2)
- printk( "mac_esp_setup: invalid number of hosts %ld !\n", opt );
-
- this_opt = strsep (&str, ",");
- }
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- if (opt > 0)
- setup_disconnect = opt;
-
- this_opt = strsep (&str, ",");
- }
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- if (opt >= 0)
- setup_nosync = opt;
-
- this_opt = strsep (&str, ",");
- }
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- if (opt > 0)
- setup_can_queue = opt;
-
- this_opt = strsep (&str, ",");
- }
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- if (opt > 0)
- setup_cmd_per_lun = opt;
-
- this_opt = strsep (&str, ",");
- }
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- if (opt >= 0) {
- setup_sg_tablesize = opt;
- /* Must be <= SG_ALL (255) */
- if (setup_sg_tablesize > SG_ALL)
- setup_sg_tablesize = SG_ALL;
- }
-
- this_opt = strsep (&str, ",");
- }
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
-
- /* Must be between 0 and 7 */
- if (opt >= 0 && opt <= 7)
- setup_hostid = opt;
- else if (opt > 7)
- printk( "mac_esp_setup: invalid host ID %ld !\n", opt);
-
- this_opt = strsep (&str, ",");
- }
-#ifdef SUPPORT_TAGS
- if(this_opt) {
- opt = simple_strtol( this_opt, NULL, 0 );
- if (opt >= 0)
- setup_use_tagged_queuing = !!opt;
- }
-#endif
-#endif
- return 1;
-}
-
-__setup("mac53c9x=", mac_esp_setup);
-
-
-/*
- * ESP address 'detection'
- */
-
-unsigned long get_base(int chip_num)
-{
- /*
- * using the chip_num and mac model, figure out where the
- * chips are mapped
- */
-
- unsigned long io_base = 0x50f00000;
- unsigned int second_offset = 0x402;
- unsigned long scsi_loc = 0;
-
- switch (macintosh_config->scsi_type) {
-
- /* 950, 900, 700 */
- case MAC_SCSI_QUADRA2:
- scsi_loc = io_base + 0xf000 + ((chip_num == 0) ? 0 : second_offset);
- break;
-
- /* av's */
- case MAC_SCSI_QUADRA3:
- scsi_loc = io_base + 0x18000 + ((chip_num == 0) ? 0 : second_offset);
- break;
-
- /* most quadra/centris models are like this */
- case MAC_SCSI_QUADRA:
- scsi_loc = io_base + 0x10000;
- break;
-
- default:
- printk("mac_esp: get_base: hit default!\n");
- scsi_loc = io_base + 0x10000;
- break;
-
- } /* switch */
-
- printk("mac_esp: io base at 0x%lx\n", scsi_loc);
-
- return scsi_loc;
-}
-
-/*
- * Model dependent ESP setup
- */
-
-int mac_esp_detect(struct scsi_host_template * tpnt)
-{
- int quick = 0;
- int chipnum, chipspresent = 0;
-#if 0
- unsigned long timeout;
-#endif
-
- if (esp_initialized > 0)
- return -ENODEV;
-
- /* what do we have in this machine... */
- if (MACHW_PRESENT(MAC_SCSI_96)) {
- chipspresent ++;
- }
-
- if (MACHW_PRESENT(MAC_SCSI_96_2)) {
- chipspresent ++;
- }
-
- /* number of ESPs present ? */
- if (setup_num_esps >= 0) {
- if (chipspresent >= setup_num_esps)
- chipspresent = setup_num_esps;
- else
- printk("mac_esp_detect: num_hosts detected %d setup %d \n",
- chipspresent, setup_num_esps);
- }
-
- /* TODO: add disconnect / nosync flags */
-
- /* setup variables */
- tpnt->can_queue =
- (setup_can_queue > 0) ? setup_can_queue : 7;
- tpnt->cmd_per_lun =
- (setup_cmd_per_lun > 0) ? setup_cmd_per_lun : 1;
- tpnt->sg_tablesize =
- (setup_sg_tablesize >= 0) ? setup_sg_tablesize : SG_ALL;
-
- if (setup_hostid >= 0)
- tpnt->this_id = setup_hostid;
- else {
- /* use 7 as default */
- tpnt->this_id = 7;
- }
-
-#ifdef SUPPORT_TAGS
- if (setup_use_tagged_queuing < 0)
- setup_use_tagged_queuing = DEFAULT_USE_TAGGED_QUEUING;
-#endif
-
- for (chipnum = 0; chipnum < chipspresent; chipnum ++) {
- struct NCR_ESP * esp;
-
- esp = esp_allocate(tpnt, NULL, 0);
- esp->eregs = (struct ESP_regs *) get_base(chipnum);
-
- esp->dma_irq_p = &esp_dafb_dma_irq_p;
- if (chipnum == 0) {
-
- if (macintosh_config->scsi_type == MAC_SCSI_QUADRA) {
- /* most machines except those below :-) */
- quick = 1;
- esp->dma_irq_p = &esp_iosb_dma_irq_p;
- } else if (macintosh_config->scsi_type == MAC_SCSI_QUADRA3) {
- /* mostly av's */
- quick = 0;
- } else {
- /* q950, 900, 700 */
- quick = 1;
- out_be32(0xf9800024, 0x1d1);
- esp->dregs = (void *) 0xf9800024;
- }
-
- } else { /* chipnum */
-
- quick = 1;
- out_be32(0xf9800028, 0x1d1);
- esp->dregs = (void *) 0xf9800028;
-
- } /* chipnum == 0 */
-
- /* use pio for command bytes; pio for message/data: TBI */
- esp->do_pio_cmds = 1;
-
- /* Set the command buffer */
- esp->esp_command = (volatile unsigned char*) cmd_buffer;
- esp->esp_command_dvma = (__u32) cmd_buffer;
-
- /* various functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = NULL;
- esp->dma_init_write = NULL;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
-
- esp->dma_ports_p = &dma_ports_p;
-
-
- /* Optional functions */
- esp->dma_barrier = NULL;
- esp->dma_drain = NULL;
- esp->dma_invalidate = NULL;
- esp->dma_irq_entry = NULL;
- esp->dma_irq_exit = NULL;
- esp->dma_led_on = NULL;
- esp->dma_led_off = NULL;
- esp->dma_poll = NULL;
- esp->dma_reset = NULL;
-
- /* SCSI chip speed */
- /* below esp->cfreq = 40000000; */
-
-
- if (quick) {
- /* 'quick' means there's handshake glue logic like in the 5380 case */
- esp->dma_setup = &dma_setup_quick;
- } else {
- esp->dma_setup = &dma_setup;
- }
-
- if (chipnum == 0) {
-
- esp->irq = IRQ_MAC_SCSI;
-
- request_irq(IRQ_MAC_SCSI, esp_intr, 0, "Mac ESP SCSI", esp->ehost);
-#if 0 /* conflicts with IOP ADB */
- request_irq(IRQ_MAC_SCSIDRQ, fake_drq, 0, "Mac ESP DRQ", esp->ehost);
-#endif
-
- if (macintosh_config->scsi_type == MAC_SCSI_QUADRA) {
- esp->cfreq = 16500000;
- } else {
- esp->cfreq = 25000000;
- }
-
-
- } else { /* chipnum == 1 */
-
- esp->irq = IRQ_MAC_SCSIDRQ;
-#if 0 /* conflicts with IOP ADB */
- request_irq(IRQ_MAC_SCSIDRQ, esp_intr, 0, "Mac ESP SCSI 2", esp->ehost);
-#endif
-
- esp->cfreq = 25000000;
-
- }
-
- if (quick) {
- printk("esp: using quick version\n");
- }
-
- printk("esp: addr at 0x%p\n", esp->eregs);
-
- esp->scsi_id = 7;
- esp->diff = 0;
-
- esp_initialize(esp);
-
- } /* for chipnum */
-
- if (chipspresent)
- printk("\nmac_esp: %d esp controllers found\n", chipspresent);
-
- esp_initialized = chipspresent;
-
- return chipspresent;
-}
-
-static int mac_esp_release(struct Scsi_Host *shost)
-{
- if (shost->irq)
- free_irq(shost->irq, NULL);
- if (shost->io_port && shost->n_io_port)
- release_region(shost->io_port, shost->n_io_port);
- scsi_unregister(shost);
- return 0;
-}
-
-/*
- * I've been wondering what this is supposed to do, for some time. Talking
- * to Allen Briggs: These machines have an extra register someplace where the
- * DRQ pin of the ESP can be monitored. That isn't useful for determining
- * anything else (such as reselect interrupt or other magic) though.
- * Maybe make the semantics should be changed like
- * if (esp->current_SC)
- * ... check DRQ flag ...
- * else
- * ... disconnected, check pending VIA interrupt ...
- *
- * There's a problem with using the dabf flag or mac_irq_pending() here: both
- * seem to return 1 even though no interrupt is currently pending, resulting
- * in esp_exec_cmd() holding off the next command, and possibly infinite loops
- * in esp_intr().
- * Short term fix: just use esp_status & ESP_STAT_INTR here, as long as we
- * use simple PIO. The DRQ status will be important when implementing pseudo
- * DMA mode (set up ESP transfer count, return, do a batch of bytes in PIO or
- * 'hardware handshake' mode upon DRQ).
- * If you plan on changing this (i.e. to save the esp_status register access in
- * favor of a VIA register access or a shadow register for the IFR), make sure
- * to try a debug version of this first to monitor what registers would be a good
- * indicator of the ESP interrupt.
- */
-
-static int esp_dafb_dma_irq_p(struct NCR_ESP * esp)
-{
- unsigned int ret;
- int sreg = esp_read(esp->eregs->esp_status);
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: esp_dafb_dma_irq_p dafb %d irq %d\n",
- readl(esp->dregs), mac_irq_pending(IRQ_MAC_SCSI));
-#endif
-
- sreg &= ESP_STAT_INTR;
-
- /*
- * maybe working; this is essentially what's used for iosb_dma_irq_p
- */
- if (sreg)
- return 1;
- else
- return 0;
-
- /*
- * didn't work ...
- */
-#if 0
- if (esp->current_SC)
- ret = readl(esp->dregs) & 0x200;
- else if (esp->disconnected_SC)
- ret = 1; /* sreg ?? */
- else
- ret = mac_irq_pending(IRQ_MAC_SCSI);
-
- return(ret);
-#endif
-
-}
-
-/*
- * See above: testing mac_irq_pending always returned 8 (SCSI IRQ) regardless
- * of the actual ESP status.
- */
-
-static int esp_iosb_dma_irq_p(struct NCR_ESP * esp)
-{
- int ret = mac_irq_pending(IRQ_MAC_SCSI) || mac_irq_pending(IRQ_MAC_SCSIDRQ);
- int sreg = esp_read(esp->eregs->esp_status);
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_irq_p drq %d irq %d sreg %x curr %p disc %p\n",
- mac_irq_pending(IRQ_MAC_SCSIDRQ), mac_irq_pending(IRQ_MAC_SCSI),
- sreg, esp->current_SC, esp->disconnected_SC);
-#endif
-
- sreg &= ESP_STAT_INTR;
-
- if (sreg)
- return (sreg);
- else
- return 0;
-}
-
-/*
- * This seems to be OK for PIO at least ... usually 0 after PIO.
- */
-
-static int dma_bytes_sent(struct NCR_ESP * esp, int fifo_count)
-{
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma bytes sent = %x\n", fifo_count);
-#endif
-
- return fifo_count;
-}
-
-/*
- * dma_can_transfer is used to switch between DMA and PIO, if DMA (pseudo)
- * is ever implemented. Returning 0 here will use PIO.
- */
-
-static int dma_can_transfer(struct NCR_ESP * esp, Scsi_Cmnd * sp)
-{
- unsigned long sz = sp->SCp.this_residual;
-#if 0 /* no DMA yet; make conditional */
- if (sz > 0x10000000) {
- sz = 0x10000000;
- }
- printk("mac_esp: dma can transfer = 0lx%x\n", sz);
-#else
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: pio to transfer = %ld\n", sz);
-#endif
-
- sz = 0;
-#endif
- return sz;
-}
-
-/*
- * Not yet ...
- */
-
-static void dma_dump_state(struct NCR_ESP * esp)
-{
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_dump_state: called\n");
-#endif
-#if 0
- ESPLOG(("esp%d: dma -- cond_reg<%02x>\n",
- esp->esp_id, ((struct mac_dma_registers *)
- (esp->dregs))->cond_reg));
-#endif
-}
-
-/*
- * DMA setup: should be used to set up the ESP transfer count for pseudo
- * DMA transfers; need a DRQ transfer function to do the actual transfer
- */
-
-static void dma_init_read(struct NCR_ESP * esp, char * vaddress, int length)
-{
- printk("mac_esp: dma_init_read\n");
-}
-
-
-static void dma_init_write(struct NCR_ESP * esp, char * vaddress, int length)
-{
- printk("mac_esp: dma_init_write\n");
-}
-
-
-static void dma_ints_off(struct NCR_ESP * esp)
-{
- disable_irq(esp->irq);
-}
-
-
-static void dma_ints_on(struct NCR_ESP * esp)
-{
- enable_irq(esp->irq);
-}
-
-/*
- * generic dma_irq_p(), unused
- */
-
-static int dma_irq_p(struct NCR_ESP * esp)
-{
- int i = esp_read(esp->eregs->esp_status);
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_irq_p status %d\n", i);
-#endif
-
- return (i & ESP_STAT_INTR);
-}
-
-static int dma_irq_p_quick(struct NCR_ESP * esp)
-{
- /*
- * Copied from iosb_dma_irq_p()
- */
- int ret = mac_irq_pending(IRQ_MAC_SCSI) || mac_irq_pending(IRQ_MAC_SCSIDRQ);
- int sreg = esp_read(esp->eregs->esp_status);
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_irq_p drq %d irq %d sreg %x curr %p disc %p\n",
- mac_irq_pending(IRQ_MAC_SCSIDRQ), mac_irq_pending(IRQ_MAC_SCSI),
- sreg, esp->current_SC, esp->disconnected_SC);
-#endif
-
- sreg &= ESP_STAT_INTR;
-
- if (sreg)
- return (sreg);
- else
- return 0;
-
-}
-
-static void dma_led_off(struct NCR_ESP * esp)
-{
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_led_off: called\n");
-#endif
-}
-
-
-static void dma_led_on(struct NCR_ESP * esp)
-{
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_led_on: called\n");
-#endif
-}
-
-
-static int dma_ports_p(struct NCR_ESP * esp)
-{
- return 0;
-}
-
-
-static void dma_setup(struct NCR_ESP * esp, __u32 addr, int count, int write)
-{
-
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_setup\n");
-#endif
-
- if (write) {
- dma_init_read(esp, (char *) addr, count);
- } else {
- dma_init_write(esp, (char *) addr, count);
- }
-}
-
-
-static void dma_setup_quick(struct NCR_ESP * esp, __u32 addr, int count, int write)
-{
-#ifdef DEBUG_MAC_ESP
- printk("mac_esp: dma_setup_quick\n");
-#endif
-}
-
-static struct scsi_host_template driver_template = {
- .proc_name = "mac_esp",
- .name = "Mac 53C9x SCSI",
- .detect = mac_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = mac_esp_release,
- .info = esp_info,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = DISABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/mca_53c9x.c b/drivers/scsi/mca_53c9x.c
deleted file mode 100644
index d693d0f..0000000
--- a/drivers/scsi/mca_53c9x.c
+++ /dev/null
@@ -1,520 +0,0 @@
-/* mca_53c9x.c: Driver for the SCSI adapter found on NCR 35xx
- * (and maybe some other) Microchannel machines
- *
- * Code taken mostly from Cyberstorm SCSI drivers
- * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
- *
- * Hacked to work with the NCR MCA stuff by Tymm Twillman (tymm@computer.org)
- *
- * The CyberStorm SCSI driver (and this driver) is based on David S. Miller's
- * ESP driver * for the Sparc computers.
- *
- * Special thanks to Ken Stewart at Symbios (LSI) for helping with info on
- * the 86C01. I was on the brink of going ga-ga...
- *
- * Also thanks to Jesper Skov for helping me with info on how the Amiga
- * does things...
- */
-
-/*
- * This is currently only set up to use one 53c9x card at a time; it could be
- * changed fairly easily to detect/use more than one, but I'm not too sure how
- * many cards that use the 53c9x on MCA systems there are (if, in fact, there
- * are cards that use them, other than the one built into some NCR systems)...
- * If anyone requests this, I'll throw it in, otherwise it's not worth the
- * effort.
- */
-
-/*
- * Info on the 86C01 MCA interface chip at the bottom, if you care enough to
- * look.
- */
-
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/mca.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/mca-legacy.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <asm/dma.h>
-#include <asm/irq.h>
-#include <asm/mca_dma.h>
-#include <asm/pgtable.h>
-
-/*
- * From ibmmca.c (IBM scsi controller card driver) -- used for turning PS2 disk
- * activity LED on and off
- */
-
-#define PS2_SYS_CTR 0x92
-
-/* Ports the ncr's 53c94 can be put at; indexed by pos register value */
-
-#define MCA_53C9X_IO_PORTS { \
- 0x0000, 0x0240, 0x0340, 0x0400, \
- 0x0420, 0x3240, 0x8240, 0xA240, \
- }
-
-/*
- * Supposedly there were some cards put together with the 'c9x and 86c01. If
- * they have different ID's from the ones on the 3500 series machines,
- * you can add them here and hopefully things will work out.
- */
-
-#define MCA_53C9X_IDS { \
- 0x7F4C, \
- 0x0000, \
- }
-
-static int dma_bytes_sent(struct NCR_ESP *, int);
-static int dma_can_transfer(struct NCR_ESP *, Scsi_Cmnd *);
-static void dma_dump_state(struct NCR_ESP *);
-static void dma_init_read(struct NCR_ESP *, __u32, int);
-static void dma_init_write(struct NCR_ESP *, __u32, int);
-static void dma_ints_off(struct NCR_ESP *);
-static void dma_ints_on(struct NCR_ESP *);
-static int dma_irq_p(struct NCR_ESP *);
-static int dma_ports_p(struct NCR_ESP *);
-static void dma_setup(struct NCR_ESP *, __u32, int, int);
-static void dma_led_on(struct NCR_ESP *);
-static void dma_led_off(struct NCR_ESP *);
-
-/* This is where all commands are put before they are trasfered to the
- * 53c9x via PIO.
- */
-
-static volatile unsigned char cmd_buffer[16];
-
-/*
- * We keep the structure that is used to access the registers on the 53c9x
- * here.
- */
-
-static struct ESP_regs eregs;
-
-/***************************************************************** Detection */
-static int mca_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- static int io_port_by_pos[] = MCA_53C9X_IO_PORTS;
- int mca_53c9x_ids[] = MCA_53C9X_IDS;
- int *id_to_check = mca_53c9x_ids;
- int slot;
- int pos[3];
- unsigned int tmp_io_addr;
- unsigned char tmp_byte;
-
-
- if (!MCA_bus)
- return 0;
-
- while (*id_to_check) {
- if ((slot = mca_find_adapter(*id_to_check, 0)) !=
- MCA_NOTFOUND)
- {
- esp = esp_allocate(tpnt, NULL, 0);
-
- pos[0] = mca_read_stored_pos(slot, 2);
- pos[1] = mca_read_stored_pos(slot, 3);
- pos[2] = mca_read_stored_pos(slot, 4);
-
- esp->eregs = &eregs;
-
- /*
- * IO port base is given in the first (non-ID) pos
- * register, like so:
- *
- * Bits 3 2 1 IO base
- * ----------------------------
- * 0 0 0 <disabled>
- * 0 0 1 0x0240
- * 0 1 0 0x0340
- * 0 1 1 0x0400
- * 1 0 0 0x0420
- * 1 0 1 0x3240
- * 1 1 0 0x8240
- * 1 1 1 0xA240
- */
-
- tmp_io_addr =
- io_port_by_pos[(pos[0] & 0x0E) >> 1];
-
- esp->eregs->io_addr = tmp_io_addr + 0x10;
-
- if (esp->eregs->io_addr == 0x0000) {
- printk("Adapter is disabled.\n");
- break;
- }
-
- /*
- * IRQ is specified in bits 4 and 5:
- *
- * Bits 4 5 IRQ
- * -----------------------
- * 0 0 3
- * 0 1 5
- * 1 0 7
- * 1 1 9
- */
-
- esp->irq = ((pos[0] & 0x30) >> 3) + 3;
-
- /*
- * DMA channel is in the low 3 bits of the second
- * POS register
- */
-
- esp->dma = pos[1] & 7;
- esp->slot = slot;
-
- if (request_irq(esp->irq, esp_intr, 0,
- "NCR 53c9x SCSI", esp->ehost))
- {
- printk("Unable to request IRQ %d.\n", esp->irq);
- esp_deallocate(esp);
- scsi_unregister(esp->ehost);
- return 0;
- }
-
- if (request_dma(esp->dma, "NCR 53c9x SCSI")) {
- printk("Unable to request DMA channel %d.\n",
- esp->dma);
- free_irq(esp->irq, esp_intr);
- esp_deallocate(esp);
- scsi_unregister(esp->ehost);
- return 0;
- }
-
- request_region(tmp_io_addr, 32, "NCR 53c9x SCSI");
-
- /*
- * 86C01 handles DMA, IO mode, from address
- * (base + 0x0a)
- */
-
- mca_disable_dma(esp->dma);
- mca_set_dma_io(esp->dma, tmp_io_addr + 0x0a);
- mca_enable_dma(esp->dma);
-
- /* Tell the 86C01 to give us interrupts */
-
- tmp_byte = inb(tmp_io_addr + 0x02) | 0x40;
- outb(tmp_byte, tmp_io_addr + 0x02);
-
- /*
- * Scsi ID -- general purpose register, hi
- * 2 bits; add 4 to this number to get the
- * ID
- */
-
- esp->scsi_id = ((pos[2] & 0xC0) >> 6) + 4;
-
- /* Do command transfer with programmed I/O */
-
- esp->do_pio_cmds = 1;
-
- /* Required functions */
-
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
-
- esp->dma_barrier = NULL;
- esp->dma_drain = NULL;
- esp->dma_invalidate = NULL;
- esp->dma_irq_entry = NULL;
- esp->dma_irq_exit = NULL;
- esp->dma_led_on = dma_led_on;
- esp->dma_led_off = dma_led_off;
- esp->dma_poll = NULL;
- esp->dma_reset = NULL;
-
- /* Set the command buffer */
-
- esp->esp_command = (volatile unsigned char*)
- cmd_buffer;
- esp->esp_command_dvma = isa_virt_to_bus(cmd_buffer);
-
- /* SCSI chip speed */
-
- esp->cfreq = 25000000;
-
- /* Differential SCSI? I think not. */
-
- esp->diff = 0;
-
- esp_initialize(esp);
-
- printk(" Adapter found in slot %2d: io port 0x%x "
- "irq %d dma channel %d\n", slot + 1, tmp_io_addr,
- esp->irq, esp->dma);
-
- mca_set_adapter_name(slot, "NCR 53C9X SCSI Adapter");
- mca_mark_as_used(slot);
-
- break;
- }
-
- id_to_check++;
- }
-
- return esps_in_use;
-}
-
-
-/******************************************************************* Release */
-
-static int mca_esp_release(struct Scsi_Host *host)
-{
- struct NCR_ESP *esp = (struct NCR_ESP *)host->hostdata;
- unsigned char tmp_byte;
-
- esp_deallocate(esp);
- /*
- * Tell the 86C01 to stop sending interrupts
- */
-
- tmp_byte = inb(esp->eregs->io_addr - 0x0E);
- tmp_byte &= ~0x40;
- outb(tmp_byte, esp->eregs->io_addr - 0x0E);
-
- free_irq(esp->irq, esp_intr);
- free_dma(esp->dma);
-
- mca_mark_as_unused(esp->slot);
-
- return 0;
-}
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Ask the 53c9x. It knows. */
-
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- /*
- * The MCA dma channels can only do up to 128K bytes at a time.
- * (16 bit mode)
- */
-
- unsigned long sz = sp->SCp.this_residual;
- if(sz > 0x20000)
- sz = 0x20000;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- /*
- * Doesn't quite match up to the other drivers, but we do what we
- * can.
- */
-
- ESPLOG(("esp%d: dma channel <%d>\n", esp->esp_id, esp->dma));
- ESPLOG(("bytes left to dma: %d\n", mca_get_dma_residue(esp->dma)));
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
-{
- unsigned long flags;
-
-
- save_flags(flags);
- cli();
-
- mca_disable_dma(esp->dma);
- mca_set_dma_mode(esp->dma, MCA_DMA_MODE_XFER | MCA_DMA_MODE_16 |
- MCA_DMA_MODE_IO);
- mca_set_dma_addr(esp->dma, addr);
- mca_set_dma_count(esp->dma, length / 2); /* !!! */
- mca_enable_dma(esp->dma);
-
- restore_flags(flags);
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
-{
- unsigned long flags;
-
-
- save_flags(flags);
- cli();
-
- mca_disable_dma(esp->dma);
- mca_set_dma_mode(esp->dma, MCA_DMA_MODE_XFER | MCA_DMA_MODE_WRITE |
- MCA_DMA_MODE_16 | MCA_DMA_MODE_IO);
- mca_set_dma_addr(esp->dma, addr);
- mca_set_dma_count(esp->dma, length / 2); /* !!! */
- mca_enable_dma(esp->dma);
-
- restore_flags(flags);
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- /*
- * Tell the 'C01 to shut up. All interrupts are routed through it.
- */
-
- outb(inb(esp->eregs->io_addr - 0x0E) & ~0x40,
- esp->eregs->io_addr - 0x0E);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- /*
- * Ok. You can speak again.
- */
-
- outb(inb(esp->eregs->io_addr - 0x0E) | 0x40,
- esp->eregs->io_addr - 0x0E);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- /*
- * DaveM says that this should return a "yes" if there is an interrupt
- * or a DMA error occurred. I copied the Amiga driver's semantics,
- * though, because it seems to work and we can't really tell if
- * a DMA error happened. This gives the "yes" if the scsi chip
- * is sending an interrupt and no DMA activity is taking place
- */
-
- return (!(inb(esp->eregs->io_addr - 0x04) & 1) &&
- !(inb(esp->eregs->io_addr - 0x04) & 2) );
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- /*
- * Check to see if interrupts are enabled on the 'C01 (in case abort
- * is entered multiple times, so we only do the abort once)
- */
-
- return (inb(esp->eregs->io_addr - 0x0E) & 0x40) ? 1:0;
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- if(write){
- dma_init_write(esp, addr, count);
- } else {
- dma_init_read(esp, addr, count);
- }
-}
-
-/*
- * These will not play nicely with other disk controllers that try to use the
- * disk active LED... but what can you do? Don't answer that.
- *
- * Stolen shamelessly from ibmmca.c -- IBM Microchannel SCSI adapter driver
- *
- */
-
-static void dma_led_on(struct NCR_ESP *esp)
-{
- outb(inb(PS2_SYS_CTR) | 0xc0, PS2_SYS_CTR);
-}
-
-static void dma_led_off(struct NCR_ESP *esp)
-{
- outb(inb(PS2_SYS_CTR) & 0x3f, PS2_SYS_CTR);
-}
-
-static struct scsi_host_template driver_template = {
- .proc_name = "mca_53c9x",
- .name = "NCR 53c9x SCSI",
- .detect = mca_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = mca_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .unchecked_isa_dma = 1,
- .use_clustering = DISABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-/*
- * OK, here's the goods I promised. The NCR 86C01 is an MCA interface chip
- * that handles enabling/diabling IRQ, dma interfacing, IO port selection
- * and other fun stuff. It takes up 16 addresses, and the chip it is
- * connnected to gets the following 16. Registers are as follows:
- *
- * Offsets 0-1 : Card ID
- *
- * Offset 2 : Mode enable register --
- * Bit 7 : Data Word width (1 = 16, 0 = 8)
- * Bit 6 : IRQ enable (1 = enabled)
- * Bits 5,4 : IRQ select
- * 0 0 : IRQ 3
- * 0 1 : IRQ 5
- * 1 0 : IRQ 7
- * 1 1 : IRQ 9
- * Bits 3-1 : Base Address
- * 0 0 0 : <disabled>
- * 0 0 1 : 0x0240
- * 0 1 0 : 0x0340
- * 0 1 1 : 0x0400
- * 1 0 0 : 0x0420
- * 1 0 1 : 0x3240
- * 1 1 0 : 0x8240
- * 1 1 1 : 0xA240
- * Bit 0 : Card enable (1 = enabled)
- *
- * Offset 3 : DMA control register --
- * Bit 7 : DMA enable (1 = enabled)
- * Bits 6,5 : Preemt Count Select (transfers to complete after
- * 'C01 has been preempted on MCA bus)
- * 0 0 : 0
- * 0 1 : 1
- * 1 0 : 3
- * 1 1 : 7
- * (all these wacky numbers; I'm sure there's a reason somewhere)
- * Bit 4 : Fairness enable (1 = fair bus priority)
- * Bits 3-0 : Arbitration level (0-15 consecutive)
- *
- * Offset 4 : General purpose register
- * Bits 7-3 : User definable (here, 7,6 are SCSI ID)
- * Bits 2-0 : reserved
- *
- * Offset 10 : DMA decode register (used for IO based DMA; also can do
- * PIO through this port)
- *
- * Offset 12 : Status
- * Bits 7-2 : reserved
- * Bit 1 : DMA pending (1 = pending)
- * Bit 0 : IRQ pending (0 = pending)
- *
- * Exciting, huh?
- *
- */
diff --git a/drivers/scsi/oktagon_esp.c b/drivers/scsi/oktagon_esp.c
deleted file mode 100644
index 8e5eadb..0000000
--- a/drivers/scsi/oktagon_esp.c
+++ /dev/null
@@ -1,606 +0,0 @@
-/*
- * Oktagon_esp.c -- Driver for bsc Oktagon
- *
- * Written by Carsten Pluntke 1998
- *
- * Based on cyber_esp.c
- */
-
-
-#if defined(CONFIG_AMIGA) || defined(CONFIG_APUS)
-#define USE_BOTTOM_HALF
-#endif
-
-#include <linux/module.h>
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/reboot.h>
-#include <asm/system.h>
-#include <asm/ptrace.h>
-#include <asm/pgtable.h>
-
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <linux/zorro.h>
-#include <asm/irq.h>
-#include <asm/amigaints.h>
-#include <asm/amigahw.h>
-
-#ifdef USE_BOTTOM_HALF
-#include <linux/workqueue.h>
-#include <linux/interrupt.h>
-#endif
-
-/* The controller registers can be found in the Z2 config area at these
- * offsets:
- */
-#define OKTAGON_ESP_ADDR 0x03000
-#define OKTAGON_DMA_ADDR 0x01000
-
-
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 vaddress, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 vaddress, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static void dma_led_off(struct NCR_ESP *esp);
-static void dma_led_on(struct NCR_ESP *esp);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-
-static void dma_irq_exit(struct NCR_ESP *esp);
-static void dma_invalidate(struct NCR_ESP *esp);
-
-static void dma_mmu_get_scsi_one(struct NCR_ESP *,Scsi_Cmnd *);
-static void dma_mmu_get_scsi_sgl(struct NCR_ESP *,Scsi_Cmnd *);
-static void dma_mmu_release_scsi_one(struct NCR_ESP *,Scsi_Cmnd *);
-static void dma_mmu_release_scsi_sgl(struct NCR_ESP *,Scsi_Cmnd *);
-static void dma_advance_sg(Scsi_Cmnd *);
-static int oktagon_notify_reboot(struct notifier_block *this, unsigned long code, void *x);
-
-#ifdef USE_BOTTOM_HALF
-static void dma_commit(struct work_struct *unused);
-
-long oktag_to_io(long *paddr, long *addr, long len);
-long oktag_from_io(long *addr, long *paddr, long len);
-
-static DECLARE_WORK(tq_fake_dma, dma_commit);
-
-#define DMA_MAXTRANSFER 0x8000
-
-#else
-
-/*
- * No bottom half. Use transfer directly from IRQ. Find a narrow path
- * between too much IRQ overhead and clogging the IRQ for too long.
- */
-
-#define DMA_MAXTRANSFER 0x1000
-
-#endif
-
-static struct notifier_block oktagon_notifier = {
- oktagon_notify_reboot,
- NULL,
- 0
-};
-
-static long *paddress;
-static long *address;
-static long len;
-static long dma_on;
-static int direction;
-static struct NCR_ESP *current_esp;
-
-
-static volatile unsigned char cmd_buffer[16];
- /* This is where all commands are put
- * before they are trasfered to the ESP chip
- * via PIO.
- */
-
-/***************************************************************** Detection */
-int oktagon_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct zorro_dev *z = NULL;
- unsigned long address;
- struct ESP_regs *eregs;
-
- while ((z = zorro_find_device(ZORRO_PROD_BSC_OKTAGON_2008, z))) {
- unsigned long board = z->resource.start;
- if (request_mem_region(board+OKTAGON_ESP_ADDR,
- sizeof(struct ESP_regs), "NCR53C9x")) {
- /*
- * It is a SCSI controller.
- * Hardwire Host adapter to SCSI ID 7
- */
-
- address = (unsigned long)ZTWO_VADDR(board);
- eregs = (struct ESP_regs *)(address + OKTAGON_ESP_ADDR);
-
- /* This line was 5 lines lower */
- esp = esp_allocate(tpnt, (void *)board + OKTAGON_ESP_ADDR, 0);
-
- /* we have to shift the registers only one bit for oktagon */
- esp->shift = 1;
-
- esp_write(eregs->esp_cfg1, (ESP_CONFIG1_PENABLE | 7));
- udelay(5);
- if (esp_read(eregs->esp_cfg1) != (ESP_CONFIG1_PENABLE | 7))
- return 0; /* Bail out if address did not hold data */
-
- /* Do command transfer with programmed I/O */
- esp->do_pio_cmds = 1;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = 0;
- esp->dma_drain = 0;
- esp->dma_invalidate = &dma_invalidate;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = &dma_irq_exit;
- esp->dma_led_on = &dma_led_on;
- esp->dma_led_off = &dma_led_off;
- esp->dma_poll = 0;
- esp->dma_reset = 0;
-
- esp->dma_mmu_get_scsi_one = &dma_mmu_get_scsi_one;
- esp->dma_mmu_get_scsi_sgl = &dma_mmu_get_scsi_sgl;
- esp->dma_mmu_release_scsi_one = &dma_mmu_release_scsi_one;
- esp->dma_mmu_release_scsi_sgl = &dma_mmu_release_scsi_sgl;
- esp->dma_advance_sg = &dma_advance_sg;
-
- /* SCSI chip speed */
- /* Looking at the quartz of the SCSI board... */
- esp->cfreq = 25000000;
-
- /* The DMA registers on the CyberStorm are mapped
- * relative to the device (i.e. in the same Zorro
- * I/O block).
- */
- esp->dregs = (void *)(address + OKTAGON_DMA_ADDR);
-
- paddress = (long *) esp->dregs;
-
- /* ESP register base */
- esp->eregs = eregs;
-
- /* Set the command buffer */
- esp->esp_command = (volatile unsigned char*) cmd_buffer;
-
- /* Yes, the virtual address. See below. */
- esp->esp_command_dvma = (__u32) cmd_buffer;
-
- esp->irq = IRQ_AMIGA_PORTS;
- request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
- "BSC Oktagon SCSI", esp->ehost);
-
- /* Figure out our scsi ID on the bus */
- esp->scsi_id = 7;
-
- /* We don't have a differential SCSI-bus. */
- esp->diff = 0;
-
- esp_initialize(esp);
-
- printk("ESP_Oktagon Driver 1.1"
-#ifdef USE_BOTTOM_HALF
- " [BOTTOM_HALF]"
-#else
- " [IRQ]"
-#endif
- " registered.\n");
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps,esps_in_use);
- esps_running = esps_in_use;
- current_esp = esp;
- register_reboot_notifier(&oktagon_notifier);
- return esps_in_use;
- }
- }
- return 0;
-}
-
-
-/*
- * On certain configurations the SCSI equipment gets confused on reboot,
- * so we have to reset it then.
- */
-
-static int
-oktagon_notify_reboot(struct notifier_block *this, unsigned long code, void *x)
-{
- struct NCR_ESP *esp;
-
- if((code == SYS_DOWN || code == SYS_HALT) && (esp = current_esp))
- {
- esp_bootup_reset(esp,esp->eregs);
- udelay(500); /* Settle time. Maybe unnecessary. */
- }
- return NOTIFY_DONE;
-}
-
-
-
-#ifdef USE_BOTTOM_HALF
-
-
-/*
- * The bsc Oktagon controller has no real DMA, so we have to do the 'DMA
- * transfer' in the interrupt (Yikes!) or use a bottom half to not to clutter
- * IRQ's for longer-than-good.
- *
- * FIXME
- * BIG PROBLEM: 'len' is usually the buffer length, not the expected length
- * of the data. So DMA may finish prematurely, further reads lead to
- * 'machine check' on APUS systems (don't know about m68k systems, AmigaOS
- * deliberately ignores the bus faults) and a normal copy-loop can't
- * be exited prematurely just at the right moment by the dma_invalidate IRQ.
- * So do it the hard way, write an own copier in assembler and
- * catch the exception.
- * -- Carsten
- */
-
-
-static void dma_commit(struct work_struct *unused)
-{
- long wait,len2,pos;
- struct NCR_ESP *esp;
-
- ESPDATA(("Transfer: %ld bytes, Address 0x%08lX, Direction: %d\n",
- len,(long) address,direction));
- dma_ints_off(current_esp);
-
- pos = 0;
- wait = 1;
- if(direction) /* write? (memory to device) */
- {
- while(len > 0)
- {
- len2 = oktag_to_io(paddress, address+pos, len);
- if(!len2)
- {
- if(wait > 1000)
- {
- printk("Expedited DMA exit (writing) %ld\n",len);
- break;
- }
- mdelay(wait);
- wait *= 2;
- }
- pos += len2;
- len -= len2*sizeof(long);
- }
- } else {
- while(len > 0)
- {
- len2 = oktag_from_io(address+pos, paddress, len);
- if(!len2)
- {
- if(wait > 1000)
- {
- printk("Expedited DMA exit (reading) %ld\n",len);
- break;
- }
- mdelay(wait);
- wait *= 2;
- }
- pos += len2;
- len -= len2*sizeof(long);
- }
- }
-
- /* to make esp->shift work */
- esp=current_esp;
-
-#if 0
- len2 = (esp_read(current_esp->eregs->esp_tclow) & 0xff) |
- ((esp_read(current_esp->eregs->esp_tcmed) & 0xff) << 8);
-
- /*
- * Uh uh. If you see this, len and transfer count registers were out of
- * sync. That means really serious trouble.
- */
-
- if(len2)
- printk("Eeeek!! Transfer count still %ld!\n",len2);
-#endif
-
- /*
- * Normally we just need to exit and wait for the interrupt to come.
- * But at least one device (my Microtek ScanMaker 630) regularly mis-
- * calculates the bytes it should send which is really ugly because
- * it locks up the SCSI bus if not accounted for.
- */
-
- if(!(esp_read(current_esp->eregs->esp_status) & ESP_STAT_INTR))
- {
- long len = 100;
- long trash[10];
-
- /*
- * Interrupt bit was not set. Either the device is just plain lazy
- * so we give it a 10 ms chance or...
- */
- while(len-- && (!(esp_read(current_esp->eregs->esp_status) & ESP_STAT_INTR)))
- udelay(100);
-
-
- if(!(esp_read(current_esp->eregs->esp_status) & ESP_STAT_INTR))
- {
- /*
- * So we think that the transfer count is out of sync. Since we
- * have all we want we are happy and can ditch the trash.
- */
-
- len = DMA_MAXTRANSFER;
-
- while(len-- && (!(esp_read(current_esp->eregs->esp_status) & ESP_STAT_INTR)))
- oktag_from_io(trash,paddress,2);
-
- if(!(esp_read(current_esp->eregs->esp_status) & ESP_STAT_INTR))
- {
- /*
- * Things really have gone wrong. If we leave the system in that
- * state, the SCSI bus is locked forever. I hope that this will
- * turn the system in a more or less running state.
- */
- printk("Device is bolixed, trying bus reset...\n");
- esp_bootup_reset(current_esp,current_esp->eregs);
- }
- }
- }
-
- ESPDATA(("Transfer_finale: do_data_finale should come\n"));
-
- len = 0;
- dma_on = 0;
- dma_ints_on(current_esp);
-}
-
-#endif
-
-/************************************************************* DMA Functions */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- /* Since the CyberStorm DMA is fully dedicated to the ESP chip,
- * the number of bytes sent (to the ESP chip) equals the number
- * of bytes in the FIFO - there is no buffering in the DMA controller.
- * XXXX Do I read this right? It is from host to ESP, right?
- */
- return fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- unsigned long sz = sp->SCp.this_residual;
- if(sz > DMA_MAXTRANSFER)
- sz = DMA_MAXTRANSFER;
- return sz;
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
-}
-
-/*
- * What the f$@& is this?
- *
- * Some SCSI devices (like my Microtek ScanMaker 630 scanner) want to transfer
- * more data than requested. How much? Dunno. So ditch the bogus data into
- * the sink, hoping the device will advance to the next phase sooner or later.
- *
- * -- Carsten
- */
-
-static long oktag_eva_buffer[16]; /* The data sink */
-
-static void oktag_check_dma(void)
-{
- struct NCR_ESP *esp;
-
- esp=current_esp;
- if(!len)
- {
- address = oktag_eva_buffer;
- len = 2;
- /* esp_do_data sets them to zero like len */
- esp_write(current_esp->eregs->esp_tclow,2);
- esp_write(current_esp->eregs->esp_tcmed,0);
- }
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 vaddress, int length)
-{
- /* Zorro is noncached, everything else done using processor. */
- /* cache_clear(addr, length); */
-
- if(dma_on)
- panic("dma_init_read while dma process is initialized/running!\n");
- direction = 0;
- address = (long *) vaddress;
- current_esp = esp;
- len = length;
- oktag_check_dma();
- dma_on = 1;
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 vaddress, int length)
-{
- /* cache_push(addr, length); */
-
- if(dma_on)
- panic("dma_init_write while dma process is initialized/running!\n");
- direction = 1;
- address = (long *) vaddress;
- current_esp = esp;
- len = length;
- oktag_check_dma();
- dma_on = 1;
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- disable_irq(esp->irq);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- enable_irq(esp->irq);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- /* It's important to check the DMA IRQ bit in the correct way! */
- return (esp_read(esp->eregs->esp_status) & ESP_STAT_INTR);
-}
-
-static void dma_led_off(struct NCR_ESP *esp)
-{
-}
-
-static void dma_led_on(struct NCR_ESP *esp)
-{
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return ((amiga_custom.intenar) & IF_PORTS);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
- * so when (write) is true, it actually means READ!
- */
- if(write){
- dma_init_read(esp, addr, count);
- } else {
- dma_init_write(esp, addr, count);
- }
-}
-
-/*
- * IRQ entry when DMA transfer is ready to be started
- */
-
-static void dma_irq_exit(struct NCR_ESP *esp)
-{
-#ifdef USE_BOTTOM_HALF
- if(dma_on)
- {
- schedule_work(&tq_fake_dma);
- }
-#else
- while(len && !dma_irq_p(esp))
- {
- if(direction)
- *paddress = *address++;
- else
- *address++ = *paddress;
- len -= (sizeof(long));
- }
- len = 0;
- dma_on = 0;
-#endif
-}
-
-/*
- * IRQ entry when DMA has just finished
- */
-
-static void dma_invalidate(struct NCR_ESP *esp)
-{
-}
-
-/*
- * Since the processor does the data transfer we have to use the custom
- * mmu interface to pass the virtual address, not the physical.
- */
-
-void dma_mmu_get_scsi_one(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- sp->SCp.ptr =
- sp->request_buffer;
-}
-
-void dma_mmu_get_scsi_sgl(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- sp->SCp.ptr = sg_virt(sp->SCp.buffer);
-}
-
-void dma_mmu_release_scsi_one(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
-}
-
-void dma_mmu_release_scsi_sgl(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
-}
-
-void dma_advance_sg(Scsi_Cmnd *sp)
-{
- sp->SCp.ptr = sg_virt(sp->SCp.buffer);
-}
-
-
-#define HOSTS_C
-
-int oktagon_esp_release(struct Scsi_Host *instance)
-{
-#ifdef MODULE
- unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
- esp_release();
- release_mem_region(address, sizeof(struct ESP_regs));
- free_irq(IRQ_AMIGA_PORTS, esp_intr);
- unregister_reboot_notifier(&oktagon_notifier);
-#endif
- return 1;
-}
-
-
-static struct scsi_host_template driver_template = {
- .proc_name = "esp-oktagon",
- .proc_info = &esp_proc_info,
- .name = "BSC Oktagon SCSI",
- .detect = oktagon_esp_detect,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .release = oktagon_esp_release,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
diff --git a/drivers/scsi/oktagon_io.S b/drivers/scsi/oktagon_io.S
deleted file mode 100644
index 8a7340b..0000000
--- a/drivers/scsi/oktagon_io.S
+++ /dev/null
@@ -1,194 +0,0 @@
-/* -*- mode: asm -*-
- * Due to problems while transferring data I've put these routines as assembly
- * code.
- * Since I'm no PPC assembler guru, the code is just the assembler version of
-
-int oktag_to_io(long *paddr,long *addr,long len)
-{
- long *addr2 = addr;
- for(len=(len+sizeof(long)-1)/sizeof(long);len--;)
- *paddr = *addr2++;
- return addr2 - addr;
-}
-
-int oktag_from_io(long *addr,long *paddr,long len)
-{
- long *addr2 = addr;
- for(len=(len+sizeof(long)-1)/sizeof(long);len--;)
- *addr2++ = *paddr;
- return addr2 - addr;
-}
-
- * assembled using gcc -O2 -S, with two exception catch points where data
- * is moved to/from the IO register.
- */
-
-
-#ifdef CONFIG_APUS
-
- .file "oktagon_io.c"
-
-gcc2_compiled.:
-/*
- .section ".text"
-*/
- .align 2
- .globl oktag_to_io
- .type oktag_to_io,@function
-oktag_to_io:
- addi 5,5,3
- srwi 5,5,2
- cmpwi 1,5,0
- mr 9,3
- mr 3,4
- addi 5,5,-1
- bc 12,6,.L3
-.L5:
- cmpwi 1,5,0
- lwz 0,0(3)
- addi 3,3,4
- addi 5,5,-1
-exp1: stw 0,0(9)
- bc 4,6,.L5
-.L3:
-ret1: subf 3,4,3
- srawi 3,3,2
- blr
-.Lfe1:
- .size oktag_to_io,.Lfe1-oktag_to_io
- .align 2
- .globl oktag_from_io
- .type oktag_from_io,@function
-oktag_from_io:
- addi 5,5,3
- srwi 5,5,2
- cmpwi 1,5,0
- mr 9,3
- addi 5,5,-1
- bc 12,6,.L9
-.L11:
- cmpwi 1,5,0
-exp2: lwz 0,0(4)
- addi 5,5,-1
- stw 0,0(3)
- addi 3,3,4
- bc 4,6,.L11
-.L9:
-ret2: subf 3,9,3
- srawi 3,3,2
- blr
-.Lfe2:
- .size oktag_from_io,.Lfe2-oktag_from_io
- .ident "GCC: (GNU) egcs-2.90.29 980515 (egcs-1.0.3 release)"
-
-/*
- * Exception table.
- * Second longword shows where to jump when an exception at the addr the first
- * longword is pointing to is caught.
- */
-
-.section __ex_table,"a"
- .align 2
-oktagon_except:
- .long exp1,ret1
- .long exp2,ret2
-
-#else
-
-/*
-The code which follows is for 680x0 based assembler and is meant for
-Linux/m68k. It was created by cross compiling the code using the
-instructions given above. I then added the four labels used in the
-exception handler table at the bottom of this file.
-- Kevin <kcozens@interlog.com>
-*/
-
-#ifdef CONFIG_AMIGA
-
- .file "oktagon_io.c"
- .version "01.01"
-gcc2_compiled.:
-.text
- .align 2
-.globl oktag_to_io
- .type oktag_to_io,@function
-oktag_to_io:
- link.w %a6,#0
- move.l %d2,-(%sp)
- move.l 8(%a6),%a1
- move.l 12(%a6),%d1
- move.l %d1,%a0
- move.l 16(%a6),%d0
- addq.l #3,%d0
- lsr.l #2,%d0
- subq.l #1,%d0
- moveq.l #-1,%d2
- cmp.l %d0,%d2
- jbeq .L3
-.L5:
-exp1:
- move.l (%a0)+,(%a1)
- dbra %d0,.L5
- clr.w %d0
- subq.l #1,%d0
- jbcc .L5
-.L3:
-ret1:
- move.l %a0,%d0
- sub.l %d1,%d0
- asr.l #2,%d0
- move.l -4(%a6),%d2
- unlk %a6
- rts
-
-.Lfe1:
- .size oktag_to_io,.Lfe1-oktag_to_io
- .align 2
-.globl oktag_from_io
- .type oktag_from_io,@function
-oktag_from_io:
- link.w %a6,#0
- move.l %d2,-(%sp)
- move.l 8(%a6),%d1
- move.l 12(%a6),%a1
- move.l %d1,%a0
- move.l 16(%a6),%d0
- addq.l #3,%d0
- lsr.l #2,%d0
- subq.l #1,%d0
- moveq.l #-1,%d2
- cmp.l %d0,%d2
- jbeq .L9
-.L11:
-exp2:
- move.l (%a1),(%a0)+
- dbra %d0,.L11
- clr.w %d0
- subq.l #1,%d0
- jbcc .L11
-.L9:
-ret2:
- move.l %a0,%d0
- sub.l %d1,%d0
- asr.l #2,%d0
- move.l -4(%a6),%d2
- unlk %a6
- rts
-.Lfe2:
- .size oktag_from_io,.Lfe2-oktag_from_io
- .ident "GCC: (GNU) 2.7.2.1"
-
-/*
- * Exception table.
- * Second longword shows where to jump when an exception at the addr the first
- * longword is pointing to is caught.
- */
-
-.section __ex_table,"a"
- .align 2
-oktagon_except:
- .long exp1,ret1
- .long exp2,ret2
-
-#endif
-#endif
diff --git a/drivers/scsi/sun3x_esp.c b/drivers/scsi/sun3x_esp.c
deleted file mode 100644
index 1bc4190..0000000
--- a/drivers/scsi/sun3x_esp.c
+++ /dev/null
@@ -1,392 +0,0 @@
-/* sun3x_esp.c: EnhancedScsiProcessor Sun3x SCSI driver code.
- *
- * (C) 1999 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
- *
- * Based on David S. Miller's esp driver
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/proc_fs.h>
-#include <linux/stat.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-
-#include "scsi.h"
-#include <scsi/scsi_host.h>
-#include "NCR53C9x.h"
-
-#include <asm/sun3x.h>
-#include <asm/dvma.h>
-#include <asm/irq.h>
-
-static void dma_barrier(struct NCR_ESP *esp);
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_drain(struct NCR_ESP *esp);
-static void dma_invalidate(struct NCR_ESP *esp);
-static void dma_dump_state(struct NCR_ESP *esp);
-static void dma_init_read(struct NCR_ESP *esp, __u32 vaddress, int length);
-static void dma_init_write(struct NCR_ESP *esp, __u32 vaddress, int length);
-static void dma_ints_off(struct NCR_ESP *esp);
-static void dma_ints_on(struct NCR_ESP *esp);
-static int dma_irq_p(struct NCR_ESP *esp);
-static void dma_poll(struct NCR_ESP *esp, unsigned char *vaddr);
-static int dma_ports_p(struct NCR_ESP *esp);
-static void dma_reset(struct NCR_ESP *esp);
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
-static void dma_mmu_get_scsi_one (struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_mmu_get_scsi_sgl (struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_mmu_release_scsi_one (struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_mmu_release_scsi_sgl (struct NCR_ESP *esp, Scsi_Cmnd *sp);
-static void dma_advance_sg (Scsi_Cmnd *sp);
-
-/* Detecting ESP chips on the machine. This is the simple and easy
- * version.
- */
-int sun3x_esp_detect(struct scsi_host_template *tpnt)
-{
- struct NCR_ESP *esp;
- struct ConfigDev *esp_dev;
-
- esp_dev = 0;
- esp = esp_allocate(tpnt, esp_dev, 0);
-
- /* Do command transfer with DMA */
- esp->do_pio_cmds = 0;
-
- /* Required functions */
- esp->dma_bytes_sent = &dma_bytes_sent;
- esp->dma_can_transfer = &dma_can_transfer;
- esp->dma_dump_state = &dma_dump_state;
- esp->dma_init_read = &dma_init_read;
- esp->dma_init_write = &dma_init_write;
- esp->dma_ints_off = &dma_ints_off;
- esp->dma_ints_on = &dma_ints_on;
- esp->dma_irq_p = &dma_irq_p;
- esp->dma_ports_p = &dma_ports_p;
- esp->dma_setup = &dma_setup;
-
- /* Optional functions */
- esp->dma_barrier = &dma_barrier;
- esp->dma_invalidate = &dma_invalidate;
- esp->dma_drain = &dma_drain;
- esp->dma_irq_entry = 0;
- esp->dma_irq_exit = 0;
- esp->dma_led_on = 0;
- esp->dma_led_off = 0;
- esp->dma_poll = &dma_poll;
- esp->dma_reset = &dma_reset;
-
- /* virtual DMA functions */
- esp->dma_mmu_get_scsi_one = &dma_mmu_get_scsi_one;
- esp->dma_mmu_get_scsi_sgl = &dma_mmu_get_scsi_sgl;
- esp->dma_mmu_release_scsi_one = &dma_mmu_release_scsi_one;
- esp->dma_mmu_release_scsi_sgl = &dma_mmu_release_scsi_sgl;
- esp->dma_advance_sg = &dma_advance_sg;
-
- /* SCSI chip speed */
- esp->cfreq = 20000000;
- esp->eregs = (struct ESP_regs *)(SUN3X_ESP_BASE);
- esp->dregs = (void *)SUN3X_ESP_DMA;
-
- esp->esp_command = (volatile unsigned char *)dvma_malloc(DVMA_PAGE_SIZE);
- esp->esp_command_dvma = dvma_vtob((unsigned long)esp->esp_command);
-
- esp->irq = 2;
- if (request_irq(esp->irq, esp_intr, IRQF_DISABLED,
- "SUN3X SCSI", esp->ehost)) {
- esp_deallocate(esp);
- return 0;
- }
-
- esp->scsi_id = 7;
- esp->diff = 0;
-
- esp_initialize(esp);
-
- /* for reasons beyond my knowledge (and which should likely be fixed)
- sync mode doesn't work on a 3/80 at 5mhz. but it does at 4. */
- esp->sync_defp = 0x3f;
-
- printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps,
- esps_in_use);
- esps_running = esps_in_use;
- return esps_in_use;
-}
-
-static void dma_do_drain(struct NCR_ESP *esp)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
-
- int count = 500000;
-
- while((dregs->cond_reg & DMA_PEND_READ) && (--count > 0))
- udelay(1);
-
- if(!count) {
- printk("%s:%d timeout CSR %08lx\n", __FILE__, __LINE__, dregs->cond_reg);
- }
-
- dregs->cond_reg |= DMA_FIFO_STDRAIN;
-
- count = 500000;
-
- while((dregs->cond_reg & DMA_FIFO_ISDRAIN) && (--count > 0))
- udelay(1);
-
- if(!count) {
- printk("%s:%d timeout CSR %08lx\n", __FILE__, __LINE__, dregs->cond_reg);
- }
-
-}
-
-static void dma_barrier(struct NCR_ESP *esp)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
- int count = 500000;
-
- while((dregs->cond_reg & DMA_PEND_READ) && (--count > 0))
- udelay(1);
-
- if(!count) {
- printk("%s:%d timeout CSR %08lx\n", __FILE__, __LINE__, dregs->cond_reg);
- }
-
- dregs->cond_reg &= ~(DMA_ENABLE);
-}
-
-/* This uses various DMA csr fields and the fifo flags count value to
- * determine how many bytes were successfully sent/received by the ESP.
- */
-static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
-
- int rval = dregs->st_addr - esp->esp_command_dvma;
-
- return rval - fifo_count;
-}
-
-static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- return sp->SCp.this_residual;
-}
-
-static void dma_drain(struct NCR_ESP *esp)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
- int count = 500000;
-
- if(dregs->cond_reg & DMA_FIFO_ISDRAIN) {
- dregs->cond_reg |= DMA_FIFO_STDRAIN;
- while((dregs->cond_reg & DMA_FIFO_ISDRAIN) && (--count > 0))
- udelay(1);
- if(!count) {
- printk("%s:%d timeout CSR %08lx\n", __FILE__, __LINE__, dregs->cond_reg);
- }
-
- }
-}
-
-static void dma_invalidate(struct NCR_ESP *esp)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
-
- __u32 tmp;
- int count = 500000;
-
- while(((tmp = dregs->cond_reg) & DMA_PEND_READ) && (--count > 0))
- udelay(1);
-
- if(!count) {
- printk("%s:%d timeout CSR %08lx\n", __FILE__, __LINE__, dregs->cond_reg);
- }
-
- dregs->cond_reg = tmp | DMA_FIFO_INV;
- dregs->cond_reg &= ~DMA_FIFO_INV;
-
-}
-
-static void dma_dump_state(struct NCR_ESP *esp)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
-
- ESPLOG(("esp%d: dma -- cond_reg<%08lx> addr<%08lx>\n",
- esp->esp_id, dregs->cond_reg, dregs->st_addr));
-}
-
-static void dma_init_read(struct NCR_ESP *esp, __u32 vaddress, int length)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
-
- dregs->st_addr = vaddress;
- dregs->cond_reg |= (DMA_ST_WRITE | DMA_ENABLE);
-}
-
-static void dma_init_write(struct NCR_ESP *esp, __u32 vaddress, int length)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
-
- /* Set up the DMA counters */
-
- dregs->st_addr = vaddress;
- dregs->cond_reg = ((dregs->cond_reg & ~(DMA_ST_WRITE)) | DMA_ENABLE);
-}
-
-static void dma_ints_off(struct NCR_ESP *esp)
-{
- DMA_INTSOFF((struct sparc_dma_registers *) esp->dregs);
-}
-
-static void dma_ints_on(struct NCR_ESP *esp)
-{
- DMA_INTSON((struct sparc_dma_registers *) esp->dregs);
-}
-
-static int dma_irq_p(struct NCR_ESP *esp)
-{
- return DMA_IRQ_P((struct sparc_dma_registers *) esp->dregs);
-}
-
-static void dma_poll(struct NCR_ESP *esp, unsigned char *vaddr)
-{
- int count = 50;
- dma_do_drain(esp);
-
- /* Wait till the first bits settle. */
- while((*(volatile unsigned char *)vaddr == 0xff) && (--count > 0))
- udelay(1);
-
- if(!count) {
-// printk("%s:%d timeout expire (data %02x)\n", __FILE__, __LINE__,
-// esp_read(esp->eregs->esp_fdata));
- //mach_halt();
- vaddr[0] = esp_read(esp->eregs->esp_fdata);
- vaddr[1] = esp_read(esp->eregs->esp_fdata);
- }
-
-}
-
-static int dma_ports_p(struct NCR_ESP *esp)
-{
- return (((struct sparc_dma_registers *) esp->dregs)->cond_reg
- & DMA_INT_ENAB);
-}
-
-/* Resetting various pieces of the ESP scsi driver chipset/buses. */
-static void dma_reset(struct NCR_ESP *esp)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *)esp->dregs;
-
- /* Punt the DVMA into a known state. */
- dregs->cond_reg |= DMA_RST_SCSI;
- dregs->cond_reg &= ~(DMA_RST_SCSI);
- DMA_INTSON(dregs);
-}
-
-static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
-{
- struct sparc_dma_registers *dregs =
- (struct sparc_dma_registers *) esp->dregs;
- unsigned long nreg = dregs->cond_reg;
-
-// printk("dma_setup %c addr %08x cnt %08x\n",
-// write ? 'W' : 'R', addr, count);
-
- dma_do_drain(esp);
-
- if(write)
- nreg |= DMA_ST_WRITE;
- else {
- nreg &= ~(DMA_ST_WRITE);
- }
-
- nreg |= DMA_ENABLE;
- dregs->cond_reg = nreg;
- dregs->st_addr = addr;
-}
-
-static void dma_mmu_get_scsi_one (struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- sp->SCp.have_data_in = dvma_map((unsigned long)sp->SCp.buffer,
- sp->SCp.this_residual);
- sp->SCp.ptr = (char *)((unsigned long)sp->SCp.have_data_in);
-}
-
-static void dma_mmu_get_scsi_sgl (struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- int sz = sp->SCp.buffers_residual;
- struct scatterlist *sg = sp->SCp.buffer;
-
- while (sz >= 0) {
- sg[sz].dma_address = dvma_map((unsigned long)sg_virt(&sg[sz]),
- sg[sz].length);
- sz--;
- }
- sp->SCp.ptr=(char *)((unsigned long)sp->SCp.buffer->dma_address);
-}
-
-static void dma_mmu_release_scsi_one (struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- dvma_unmap((char *)sp->SCp.have_data_in);
-}
-
-static void dma_mmu_release_scsi_sgl (struct NCR_ESP *esp, Scsi_Cmnd *sp)
-{
- int sz = sp->use_sg - 1;
- struct scatterlist *sg = (struct scatterlist *)sp->request_buffer;
-
- while(sz >= 0) {
- dvma_unmap((char *)sg[sz].dma_address);
- sz--;
- }
-}
-
-static void dma_advance_sg (Scsi_Cmnd *sp)
-{
- sp->SCp.ptr = (char *)((unsigned long)sp->SCp.buffer->dma_address);
-}
-
-static int sun3x_esp_release(struct Scsi_Host *instance)
-{
- /* this code does not support being compiled as a module */
- return 1;
-
-}
-
-static struct scsi_host_template driver_template = {
- .proc_name = "sun3x_esp",
- .proc_info = &esp_proc_info,
- .name = "Sun ESP 100/100a/200",
- .detect = sun3x_esp_detect,
- .release = sun3x_esp_release,
- .slave_alloc = esp_slave_alloc,
- .slave_destroy = esp_slave_destroy,
- .info = esp_info,
- .queuecommand = esp_queue,
- .eh_abort_handler = esp_abort,
- .eh_bus_reset_handler = esp_reset,
- .can_queue = 7,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = DISABLE_CLUSTERING,
-};
-
-
-#include "scsi_module.c"
-
-MODULE_LICENSE("GPL");
--
1.5.3.1
^ permalink raw reply related [flat|nested] only message in thread