All of lore.kernel.org
 help / color / mirror / Atom feed
From: Carlos Limarino <climarino@yahoo.com.ar>
To: video4linux-list@redhat.com
Subject: Help needed to add support for the card Compro VideoMate X50 (CX88/XC2028)
Date: Sat, 16 Aug 2008 18:54:17 -0700 (PDT)	[thread overview]
Message-ID: <474079.21637.qm@web34503.mail.mud.yahoo.com> (raw)

Hi, 

I'm trying to add support for a CX23880 based card that uses the Xceive 2028 tuner. Support for this tuner was recently added to the kernel, I tried using similar cards already supported by the driver. The results were:

using card=62 (PowerColor RA330)

cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: 185b:e000, board: PowerColor RA330 [card=62,insmod option]
cx88[0]: TV tuner type 71, Radio tuner type 0
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
xc2028 2-0061: creating new instance
xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
cx88[0]: Asking xc2028/3028 to load firmware xc3028-v27.fw
cx88 IR (PowerColor RA330): unknown key: key=0x3f raw=0x3f down=1
cx88 IR (PowerColor RA330): unknown key: key=0x3f raw=0x3f down=0
input: cx88 IR (PowerColor RA330) as /devices/pci0000:00/0000:00:10.0/0000:02:09.0/input/input6
cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xfc000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
firmware: requesting xc3028-v27.fw
xc2028 2-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE (1), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: i2c output error: rc = -121 (should be 64)
xc2028 2-0061: -121 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE (1), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: i2c output error: rc = -121 (should be 64)
xc2028 2-0061: -121 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=FM (400), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback

using card=61 (Winfast TV2000 XP Global)

cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: 185b:e000, board: Winfast TV2000 XP Global [card=61,insmod option]
cx88[0]: TV tuner type 71, Radio tuner type 0
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
xc2028 2-0061: creating new instance
xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
cx88[0]: Asking xc2028/3028 to load firmware xc3028-v27.fw
cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xfc000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
firmware: requesting xc3028-v27.fw
xc2028 2-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware

Developers of the CX18 driver found a similar problem with some cards, it seems that the pin that is used to reset the tuner changes from card to card:

http://www.gossamer-threads.com/lists/ivtv/devel/38594

Since I don't have much knowledge about driver programming, I can't find something similar to 'xceive_pin' to change & test. I would greatly appreciate any help with this.

Thank you!



      Yahoo! Cocina
Recetas prácticas y comida saludable
http://ar.mujer.yahoo.com/cocina/

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

             reply	other threads:[~2008-08-17  1:55 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-08-17  1:54 Carlos Limarino [this message]
2008-08-17 17:20 ` Help needed to add support for the card Compro VideoMate X50 (CX88/XC2028) Carlos Limarino

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=474079.21637.qm@web34503.mail.mud.yahoo.com \
    --to=climarino@yahoo.com.ar \
    --cc=video4linux-list@redhat.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.