MPC880: i2cer register says tx is done but tx buf descriptor is still ready

MPC880: i2cer register says tx is done but tx buf descriptor is still ready

[DI BACCO ANTONIO - technolabs]

How could it be possible? It happens during the first i2c transactions
and then no more.=20

Bye,
Antonio.

Re: MPC880: i2cer register says tx is done but tx buf descriptor is still ready

[Jochen Friedrich]

Hi Antonio,

> How could it be possible? It happens during the first i2c transactions
> and then no more. 
>   

What linux version? Which driver?

Thanks,
Jochen

RE: MPC880: i2cer register says tx is done but tx buf descriptor is still ready

[DI BACCO ANTONIO - technolabs]

[-- Attachment #1: Type: text/plain, Size: 1589 bytes --]

A porting of the driver included in kernel 2.4.

Here is an excerpt of the method to send bytes over the i2c bus:
________________________________________________________________________
  i2c->i2c_i2cmr = 0x00;	/* Disable I2C interupts */
  i2c->i2c_i2cer = 0xff;
  i2c->i2c_i2mod |= 1;	/* Enable */
  i2c->i2c_i2com |= 0x80;	/* Begin transmission */
  tmo = jiffies + 1*HZ;
  /* Busy wait, with a timeout */
  while(!(i2c->i2c_i2cer & 0x12 || time_after(jiffies, tmo)));
  

  if (signal_pending(current) || !tmo){
    force_close(algo_8xx_data);
    if (!tmo)
        printk("IIC write: timeout!\n");

    return -EIO;
  }

  if ((tbdf[0]->cbd_sc | tbdf[1]->cbd_sc) & BD_SC_NAK) {
      printk(KERN_INFO "IIC write; no ack\n");
      if (cpm_debug > 0)
        printk("tx0 sc %04x, tx1 sc %04x\n", tbdf[0]->cbd_sc,tbdf[1]->cbd_sc);
    
    return 0;
  }

  if ((tbdf[0]->cbd_sc | tbdf[1]->cbd_sc) & BD_SC_READY) {
      printk(KERN_INFO "IIC write; complete but tbuf ready\n");
      if (cpm_debug > 0)
        printk("tx0 sc %04x, tx1 sc %04x\n", tbdf[0]->cbd_sc,tbdf[1]->cbd_sc);

    return 0;
  }


-----Original Message-----
From: Jochen Friedrich [mailto:jochen@scram.de]
Sent: Sat 17/11/2007 19.32
To: DI BACCO ANTONIO - technolabs
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: MPC880: i2cer register says tx is done but tx buf descriptor is still	ready
 
Hi Antonio,

> How could it be possible? It happens during the first i2c transactions
> and then no more. 
>   

What linux version? Which driver?

Thanks,
Jochen



[-- Attachment #2: Type: text/html, Size: 2875 bytes --]

Re: MPC880: i2cer register says tx is done but tx buf descriptor is still ready

[Ankur Maheshwari]

Hi Antonio,

Check  how is your tx_buf is allocated, if its 2.4 kernel , then try 
allocating  using following function

tx_buf = (u_char *)m8xx_cpm_hostalloc(512);

512 is the size, also dump and check the difference in start address.

I more recommendation, check how your Serial/Network driver has 
allocated memory, try using same method.

thanks,
Ankur



DI BACCO ANTONIO - technolabs wrote:
>
> A porting of the driver included in kernel 2.4.
>
> Here is an excerpt of the method to send bytes over the i2c bus:
> ________________________________________________________________________
>   i2c->i2c_i2cmr = 0x00;        /* Disable I2C interupts */
>   i2c->i2c_i2cer = 0xff;
>   i2c->i2c_i2mod |= 1;  /* Enable */
>   i2c->i2c_i2com |= 0x80;       /* Begin transmission */
>   tmo = jiffies + 1*HZ;
>   /* Busy wait, with a timeout */
>   while(!(i2c->i2c_i2cer & 0x12 || time_after(jiffies, tmo)));
>  
>
>   if (signal_pending(current) || !tmo){
>     force_close(algo_8xx_data);
>     if (!tmo)
>         printk("IIC write: timeout!\n");
>
>     return -EIO;
>   }
>
>   if ((tbdf[0]->cbd_sc | tbdf[1]->cbd_sc) & BD_SC_NAK) {
>       printk(KERN_INFO "IIC write; no ack\n");
>       if (cpm_debug > 0)
>         printk("tx0 sc %04x, tx1 sc %04x\n", 
> tbdf[0]->cbd_sc,tbdf[1]->cbd_sc);
>    
>     return 0;
>   }
>
>   if ((tbdf[0]->cbd_sc | tbdf[1]->cbd_sc) & BD_SC_READY) {
>       printk(KERN_INFO "IIC write; complete but tbuf ready\n");
>       if (cpm_debug > 0)
>         printk("tx0 sc %04x, tx1 sc %04x\n", 
> tbdf[0]->cbd_sc,tbdf[1]->cbd_sc);
>
>     return 0;
>   }
>
>
> -----Original Message-----
> From: Jochen Friedrich [mailto:jochen@scram.de]
> Sent: Sat 17/11/2007 19.32
> To: DI BACCO ANTONIO - technolabs
> Cc: linuxppc-embedded@ozlabs.org
> Subject: Re: MPC880: i2cer register says tx is done but tx buf 
> descriptor is still      ready
>
> Hi Antonio,
>
> > How could it be possible? It happens during the first i2c transactions
> > and then no more.
> >  
>
> What linux version? Which driver?
>
> Thanks,
> Jochen
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded