[linux-dvb] HVR1300 not detected by ir_kbd_i2c module

[linux-dvb] HVR1300 not detected by ir_kbd_i2c module

[Rajesh Balan]

Hi,

my new HVR-1300 is not being detected by the ir_kbd_i2c.ko module. I've 
tracked down the relevant info in the ir_probe component of the module.

ir-kbd-i2c: in ir_probe. adap->id=40004
ir-kbd-i2c: in ir_probe. adap->id=1001b
ir-kbd-i2cprobe 0x18 @ cx88[0]: no
ir-kbd-i2cprobe 0x6b @ cx88[0]: no
ir-kbd-i2cprobe 0x71 @ cx88[0]: no

and then it exits.

as for my card itself, it loads all the other modules fine. The 
intialization is exactly the same as shown at   
http://de.pastebin.ca/raw/891927

except that the ir-kbd-i2c parts are not there and this line is different

tveeprom 0-0050: Hauppauge model 96019, rev C6A0, serial# 446394

my rev number is D6D3.

What do I do to help debug this?

Rajesh







_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

Re: [linux-dvb] HVR1300 not detected by ir_kbd_i2c module

[Rajesh Balan]

forgot to add. I've tried the current hg sources of both the main v4l 
repo and the hvr1300 specific repo. neither works.

Rajesh

Rajesh Balan wrote:
> Hi,
>
> my new HVR-1300 is not being detected by the ir_kbd_i2c.ko module. I've 
> tracked down the relevant info in the ir_probe component of the module.
>
> ir-kbd-i2c: in ir_probe. adap->id=40004
> ir-kbd-i2c: in ir_probe. adap->id=1001b
> ir-kbd-i2cprobe 0x18 @ cx88[0]: no
> ir-kbd-i2cprobe 0x6b @ cx88[0]: no
> ir-kbd-i2cprobe 0x71 @ cx88[0]: no
>
> and then it exits.
>
> as for my card itself, it loads all the other modules fine. The 
> intialization is exactly the same as shown at   
> http://de.pastebin.ca/raw/891927
>
> except that the ir-kbd-i2c parts are not there and this line is different
>
> tveeprom 0-0050: Hauppauge model 96019, rev C6A0, serial# 446394
>
> my rev number is D6D3.
>
> What do I do to help debug this?
>
> Rajesh
>
>
>
>
>
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>   


_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[linux-dvb] Solved!: Re: HVR1300 not detected by ir_kbd_i2c module

[Rajesh Balan]

Darron Broad pointed me to the patches available at

http://dev.kewl.org/hauppauge/   (get the sfe version for the 1300). The patches applied cleanly about the v4l main tree mercurial source.

That fixed the problem. both ir-kbd-i2c and lirc-i2c detect and initialize the IR receiver on the HVR1300 now. 

Thanks for your help Darron!

Rajesh


Rajesh Balan wrote:
> forgot to add. I've tried the current hg sources of both the main v4l 
> repo and the hvr1300 specific repo. neither works.
>
> Rajesh
>
> Rajesh Balan wrote:
>   
>> Hi,
>>
>> my new HVR-1300 is not being detected by the ir_kbd_i2c.ko module. I've 
>> tracked down the relevant info in the ir_probe component of the module.
>>
>> ir-kbd-i2c: in ir_probe. adap->id=40004
>> ir-kbd-i2c: in ir_probe. adap->id=1001b
>> ir-kbd-i2cprobe 0x18 @ cx88[0]: no
>> ir-kbd-i2cprobe 0x6b @ cx88[0]: no
>> ir-kbd-i2cprobe 0x71 @ cx88[0]: no
>>
>> and then it exits.
>>
>> as for my card itself, it loads all the other modules fine. The 
>> intialization is exactly the same as shown at   
>> http://de.pastebin.ca/raw/891927
>>
>> except that the ir-kbd-i2c parts are not there and this line is different
>>
>> tveeprom 0-0050: Hauppauge model 96019, rev C6A0, serial# 446394
>>
>> my rev number is D6D3.
>>
>> What do I do to help debug this?
>>
>> Rajesh
>>
>>
>>
>>
>>
>>
>>
>> _______________________________________________
>> linux-dvb mailing list
>> linux-dvb@linuxtv.org
>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>>
>>   
>>     
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>   


_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[linux-dvb] HVR1300 non-MCE IR Transmitter

[Rajesh Balan]

I apologize if this is not directly related to v4l development. But I 
suspect people here know the answer to this question.

Does anyone know how to activate the IR transmitter (not receiver) that 
is on the non-MCE version of the HVR-1300?  The firmware states that it 
has an IR receiver and a transmitter. The receivers works flawlessly now.

I've loaded lirc_serial and tried ports 0x2f8 and 0x3f8. my debugging of 
the kernel module indicates that data is being written to the UART (in 
both cases) using the appropriate pulse function but the LED on the 
transmitter never blinks (checked with a digital cam LCD).  I've tried 
every type supported by the lirc_serial driver. no go.

I'm beginning to suspect that the transmitter does not behave as a 
serial device and that something else needs to be done. is this correct? 
if so, does anyone know what? There is precious little information about 
the transmitting portion of the hvr1300 on the web. what do people use 
to control their cable boxes?

Thanks,

Rajesh

_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

[linux-dvb] HVR-1300 Audio Issues. Audio works but is way too loud

[Rajesh Balan]

I've managed to smack down most of the other issues I had. But the last 
issue with analog recording remains -- I can get audio but it is way too 
loud.

I'm using the hvr-1300 hg branch with the PAL-BG audio fix (last patch). 
My input is from my cable box into the composite in of the HVR-1300.

The video is fine but the audio is way too loud. It sounds like the 
internal gain setting is set way too high. no audio control (alsamixer, 
v4l2-ctl -c volume 1  etc.) seem to work. The volume never changes.

I have a sample of the audio at http://www.cs.cmu.edu/~rajesh/foo.wav

This was recorded using  arecord -D hw:1,0 -c 2 -r 48000 -f S16_LE -t 
wav > foo.wav
I've replicated this same audio problem using mythtv's live tv function 
and with mplayer (with the tv:// option)

I noticed that the audio is also finicky. I sometimes get silence or 
static until I do v4l2-ctl -i 1. This is even with a proper video being 
displayed.

Any suggestions for fixing this? for reference, cat /dev/video1 > 
foo.mpg  has perfect audio synced with the video.

Rajesh


_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb