* Time went backwards errors booting unstable cs 17557 with 64GB memory
@ 2008-05-06 15:16 Carb, Brian A
2008-05-06 15:30 ` Keir Fraser
2008-05-06 15:40 ` Bill Burns
0 siblings, 2 replies; 5+ messages in thread
From: Carb, Brian A @ 2008-05-06 15:16 UTC (permalink / raw)
To: xen-devel
[-- Attachment #1: Type: text/plain, Size: 984 bytes --]
I've built the latest xen unstable cs 17557 to run on a multi-cell
ES7000/one. When I boot with the procs and memory from a single cell (4
cores aka 8 cpus from cell0, 32gb memory from cell0), dom0 boots cleanly
. However, if I use the memory from 2 cells (4 cores aka 8 cpus from
cell0, 64gb memory interleaved from cell0 & cell1), dom0 boots
eventually, but produces multiple Timer errors as shown below. I tried
setting numa=on but timer errors persist. FYI Xen unstable cs 17318 ran
successfully without timer errors on this multi-cell configuration.
Timer ISR/0: Time went backwards: delta=-2679966594 delta_cpu=10033406
shadow=13664567457 off=530033587 processed=16874567457
cpu_processed=14184567457
0: 14184567457
1: 16874567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
The attached serial trace shows a boot with 32gb and then a boot with
64gb.
brian carb
unisys corporation - malvern, pa
[-- Attachment #2: serport.20080505 --]
[-- Type: application/octet-stream, Size: 89182 bytes --]
[-- Console up -- Mon May 5 14:34:49 2008]
__ __ _____ _____ _ _ _
\ \/ /___ _ __ |___ / |___ / _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ '_ \ |_ \ |_ \ __| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
/ \ __/ | | | ___) | ___) |__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |____(_)____/ \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
(XEN) Xen version 3.3-unstable (root@site) (gcc version 4.1.2 20070115 (prerelease) (SUSE Linux)) Fri May 2 05:32:52 EDT 2008
(XEN) Latest ChangeSet: Thu May 01 16:38:56 2008 +0100 17557:64f790e90d3d
(XEN) Command line: com1=115200,8n1 apic_verbosity=debug console=com1,vga
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 2 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009d800 (usable)
(XEN) 000000000009d800 - 00000000000a0000 (reserved)
(XEN) 00000000000ce000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 0000000037e70000 (usable)
(XEN) 0000000037e70000 - 0000000037ed7000 (ACPI data)
(XEN) 0000000037ed7000 - 0000000037f00000 (ACPI NVS)
(XEN) 0000000037f00000 - 00000000f0000000 (usable)
(XEN) 00000000f8000000 - 00000000fec00000 (reserved)
(XEN) 00000000fffc0000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000808000000 (usable)
(XEN) System RAM: 32639MB (33422388kB)
(XEN) ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f8650
(XEN) ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x06040000) @ 0x0000000037e7ddfa
(XEN) ACPI: FADT (v004 UNISYS ZORRO 0x06040000 PTL 0x00000008) @ 0x0000000037ed607c
(XEN) ACPI: OEM1 (v001 UNISYS OEM1 0x06040000 LTP 0x06040000) @ 0x0000000037ed6170
(XEN) ACPI: OEM2 (v001 UNISYS OEM2 0x06040000 LTP 0x06040000) @ 0x0000000037ed61a0
(XEN) ACPI: WSPT (v001 UNISYS WSPT 0x06040000 LTP 0x06040000) @ 0x0000000037ed6d9c
(XEN) ACPI: SRAT (v001 UNISYS SRAT 0x06040000 LTP 0x06040000) @ 0x0000000037ed6dc4
(XEN) ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x06040000) @ 0x0000000037ed6ec4
(XEN) ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x0000000037ed6fb0
(XEN) ACPI: DSDT (v001 Intel 870 SMP 0x06040000 MSFT 0x03000000) @ 0x0000000000000000
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-0000000808000000
(XEN) Xen heap: 13MB (13872kB)
(XEN) Domain heap initialised: DMA width 32 bits
(XEN) found SMP MP-table at 000f8680
(XEN) DMI present.
(XEN) UNISYS ES7000-ONE detected: force use of apic=bigsmp
(XEN) Using APIC driver bigsmp
(XEN) ACPI: PM-Timer IO Port: 0xd08
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[d04,0], pm1x_evt[d00,0]
(XEN) ACPI: wakeup_vec[37ed8fcc], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
(XEN) Processor #0 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
(XEN) Processor #4 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x08] enabled)
(XEN) Processor #8 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x0c] enabled)
(XEN) Processor #12 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
(XEN) Processor #2 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
(XEN) Processor #6 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x0a] enabled)
(XEN) Processor #10 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x0e] enabled)
(XEN) Processor #14 15:6 APIC version 20
(XEN) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: IOAPIC (id[0x08] address[0xfec02000] gsi_base[24])
(XEN) IOAPIC[1]: apic_id 8, version 32, address 0xfec02000, GSI 24-47
(XEN) ACPI: IOAPIC (id[0x09] address[0xfec03000] gsi_base[48])
(XEN) IOAPIC[2]: apic_id 9, version 32, address 0xfec03000, GSI 48-71
(XEN) ACPI: IOAPIC (id[0x0a] address[0xfec04000] gsi_base[72])
(XEN) IOAPIC[3]: apic_id 10, version 32, address 0xfec04000, GSI 72-95
(XEN) ACPI: IOAPIC (id[0x0b] address[0xfec05000] gsi_base[96])
(XEN) IOAPIC[4]: apic_id 11, version 32, address 0xfec05000, GSI 96-119
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Phys. Using 5 I/O APICs
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) mapped APIC to ffff828bfffff000 (fee00000)
(XEN) mapped IOAPIC to ffff828bffffe000 (fec00000)
(XEN) mapped IOAPIC to ffff828bffffd000 (fec02000)
(XEN) mapped IOAPIC to ffff828bffffc000 (fec03000)
(XEN) mapped IOAPIC to ffff828bffffb000 (fec04000)
(XEN) mapped IOAPIC to ffff828bffffa000 (fec05000)
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 3400.079 MHz processor.
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) HVM: VMX enabled
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU0: Thermal monitoring enabled
(XEN) CPU0: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Getting VERSION: 50014
(XEN) Getting VERSION: 50014
(XEN) Getting ID: 0
(XEN) Getting LVT0: 10700
(XEN) Getting LVT1: 10400
(XEN) masked ExtINT on CPU#0
(XEN) Booting processor 1/4 eip 8c000
(XEN) Initializing CPU#1
(XEN) masked ExtINT on CPU#1
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 1
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU1: Thermal monitoring enabled
(XEN) CPU1: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 2/8 eip 8c000
(XEN) Initializing CPU#2
(XEN) masked ExtINT on CPU#2
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 2
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU2: Thermal monitoring enabled
(XEN) CPU2: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 3/12 eip 8c000
(XEN) Initializing CPU#3
(XEN) masked ExtINT on CPU#3
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 3
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU3: Thermal monitoring enabled
(XEN) CPU3: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 4/2 eip 8c000
(XEN) Initializing CPU#4
(XEN) masked ExtINT on CPU#4
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#4.
(XEN) CPU4: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU4: Thermal monitoring enabled
(XEN) CPU4: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 5/6 eip 8c000
(XEN) Initializing CPU#5
(XEN) masked ExtINT on CPU#5
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 1
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#5.
(XEN) CPU5: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU5: Thermal monitoring enabled
(XEN) CPU5: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 6/10 eip 8c000
(XEN) Initializing CPU#6
(XEN) masked ExtINT on CPU#6
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 2
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#6.
(XEN) CPU6: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU6: Thermal monitoring enabled
(XEN) CPU6: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 7/14 eip 8c000
(XEN) Initializing CPU#7
(XEN) masked ExtINT on CPU#7
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 3
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#7.
(XEN) CPU7: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU7: Thermal monitoring enabled
(XEN) CPU7: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Total of 8 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) init IO_APIC IRQs
(XEN) IO-APIC (apicid-pin) 0-0, 0-16, 0-17, 0-18, 0-19, 0-20, 0-21, 0-22, 0-23, 8-0, 8-1, 8-2, 8-3, 8-4, 8-5, 8-6, 8-7, 8-8, 8-9, 8-10, 8-11, 8-12, 8-13, 8-14, 8-15, 8-16, 8-17, 8-18, 8-19, 8-20, 8-21, 8-22, 8-23, 9-0, 9-1, 9-2, 9-3, 9-4, 9-5, 9-6, 9-7, 9-8, 9-9, 9-10, 9-11, 9-12, 9-13, 9-14, 9-15, 9-16, 9-17, 9-18, 9-19, 9-20, 9-21, 9-22, 9-23, 10-0, 10-1, 10-2, 10-3, 10-4, 10-5, 10-6, 10-7, 10-8, 10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15, 10-16, 10-17, 10-18, 10-19, 10-20, 10-21, 10-22, 10-23, 11-0, 11-1, 11-2, 11-3, 11-4, 11-5, 11-6, 11-7, 11-8, 11-9, 11-10, 11-11, 11-12, 11-13, 11-14, 11-15, 11-16, 11-17, 11-18, 11-19, 11-20, 11-21, 11-22, 11-23 not connected.
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=0 pin2=0
(XEN) number of MP IRQ sources: 15.
(XEN) number of IO-APIC #0 registers: 24.
(XEN) number of IO-APIC #8 registers: 24.
(XEN) number of IO-APIC #9 registers: 24.
(XEN) number of IO-APIC #10 registers: 24.
(XEN) number of IO-APIC #11 registers: 24.
(XEN) testing the IO APIC.......................
(XEN) IO APIC #0......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 0 0 0 0 0 0 0 28
(XEN) 02 000 00 0 0 0 0 0 0 0 F0
(XEN) 03 000 00 0 0 0 0 0 0 0 30
(XEN) 04 000 00 0 0 0 0 0 0 0 F1
(XEN) 05 000 00 0 0 0 0 0 0 0 38
(XEN) 06 000 00 0 0 0 0 0 0 0 40
(XEN) 07 000 00 0 0 0 0 0 0 0 48
(XEN) 08 000 00 0 0 0 0 0 0 0 50
(XEN) 09 000 00 1 1 0 0 0 0 0 58
(XEN) 0a 000 00 0 0 0 0 0 0 0 60
(XEN) 0b 000 00 0 0 0 0 0 0 0 68
(XEN) 0c 000 00 0 0 0 0 0 0 0 70
(XEN) 0d 000 00 0 0 0 0 0 0 0 78
(XEN) 0e 000 00 0 0 0 0 0 0 0 88
(XEN) 0f 000 00 0 0 0 0 0 0 0 90
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #8......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #9......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #10......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #11......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) Using vector-based indexing
(XEN) IRQ to pin mappings:
(XEN) IRQ240 -> 0:2
(XEN) IRQ40 -> 0:1
(XEN) IRQ48 -> 0:3
(XEN) IRQ241 -> 0:4
(XEN) IRQ56 -> 0:5
(XEN) IRQ64 -> 0:6
(XEN) IRQ72 -> 0:7
(XEN) IRQ80 -> 0:8
(XEN) IRQ88 -> 0:9
(XEN) IRQ96 -> 0:10
(XEN) IRQ104 -> 0:11
(XEN) IRQ112 -> 0:12
(XEN) IRQ120 -> 0:13
(XEN) IRQ136 -> 0:14
(XEN) IRQ144 -> 0:15
(XEN) .................................... done.
(XEN) Using local APIC timer interrupts.
(XEN) calibrating APIC timer ...
(XEN) ..... CPU clock speed is 3399.9879 MHz.
(XEN) ..... host bus clock speed is 199.9992 MHz.
(XEN) ..... bus_scale = 0x0000CCCC
(XEN) checking TSC synchronization across 8 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
(XEN) Brought up 8 CPUs
(XEN) I/O virtualisation disabled
(XEN) <PM> ACPI (supports S3)
(XEN) Machine check exception polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x2628e8
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80463000 memsz=0x8b948
(XEN) elf_parse_binary: phdr: paddr=0xffffffff804ef000 memsz=0xc08
(XEN) elf_parse_binary: phdr: paddr=0xffffffff804f0000 memsz=0xce58c
(XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff805be58c
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: FEATURES = "writable_page_tables|writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|supervisor_mode_kernel"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_parse: using notes from SHT_NOTE section
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0xffffffff80000000
(XEN) virt_offset = 0x0
(XEN) virt_kstart = 0xffffffff80200000
(XEN) virt_kend = 0xffffffff805be58c
(XEN) virt_entry = 0xffffffff80200000
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 -> 0xffffffff805be58c
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 00000007e0000000->00000007e8000000 (8177913 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80200000->ffffffff805be58c
(XEN) Init. ramdisk: ffffffff805bf000->ffffffff80cdf800
(XEN) Phys-Mach map: ffffffff80ce0000->ffffffff84b847c8
(XEN) Start info: ffffffff84b85000->ffffffff84b854a4
(XEN) Page tables: ffffffff84b86000->ffffffff84bb1000
(XEN) Boot stack: ffffffff84bb1000->ffffffff84bb2000
(XEN) TOTAL: ffffffff80000000->ffffffff85000000
(XEN) ENTRY ADDRESS: ffffffff80200000
(XEN) Dom0 has maximum 8 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff804628e8
(XEN) elf_load_binary: phdr 1 at 0xffffffff80463000 -> 0xffffffff804ee948
(XEN) elf_load_binary: phdr 2 at 0xffffffff804ef000 -> 0xffffffff804efc08
(XEN) elf_load_binary: phdr 3 at 0xffffffff804f0000 -> 0xffffffff8052a108
(XEN) Initrd len 0x720800, start at 0xffffffff805bf000
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 120kB init memory.
kernel direct mapping tables up to 7d50f9000 @ 4bcf000-8a99000
Bootdata ok (command line is root=/dev/disk/by-id/scsi-3600508e000000000ff4df9da7f80cc05-part1 vga=0x314 resume=/dev/sda2 splash=silent showopts debug=y )
Linux version 2.6.18.8-xen (root@m0075-p0) (gcc version 4.1.2 20070115 (prerelease) (SUSE Linux)) #1 SMP Fri May 2 06:05:38 EDT 2008
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 00000007d50f9000 (usable)
DMI present.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x08] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x0c] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x0a] enabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x0e] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x08] address[0xfec02000] gsi_base[24])
IOAPIC[1]: apic_id 8, version 32, address 0xfec02000, GSI 24-47
ACPI: IOAPIC (id[0x09] address[0xfec03000] gsi_base[48])
IOAPIC[2]: apic_id 9, version 32, address 0xfec03000, GSI 48-71
ACPI: IOAPIC (id[0x0a] address[0xfec04000] gsi_base[72])
IOAPIC[3]: apic_id 10, version 32, address 0xfec04000, GSI 72-95
ACPI: IOAPIC (id[0x0b] address[0xfec05000] gsi_base[96])
IOAPIC[4]: apic_id 11, version 32, address 0xfec05000, GSI 96-119
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at f0800000 (gap: f0000000:8000000)
Built 1 zonelists. Total pages: 8100446
Kernel command line: root=/dev/disk/by-id/scsi-3600508e000000000ff4df9da7f80cc05-part1 vga=0x314 resume=/dev/sda2 splash=silent showopts debug=y
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 3399.938 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)
Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Software IO TLB enabled:
Aperture: 64 megabytes
Kernel range: ffff880028116000 - ffff88002c116000
Address size: 27 bits
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Memory: 32135772k/32850916k available (2025k kernel code, 706076k reserved, 891k data, 176k init)
Calibrating delay using timer specific routine.. 6803.33 BogoMIPS (lpj=34016681)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
SMP alternatives: switching to SMP code
Initializing CPU#1
Initializing CPU#2
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Initializing CPU#3
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
Initializing CPU#4
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Initializing CPU#5
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Initializing CPU#6
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
Brought up 8 CPUs
Initializing CPU#7
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
migration_cost=7045
checking if image is initramfs... it is
Freeing initrd memory: 7298k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: Device [MBDV] status [00000008]: functional but not present; setting present
ACPI: PCI Root Bridge [MBDV] (0000:ff)
ACPI: Device [MEDV] status [00000008]: functional but not present; setting present
ACPI: PCI Root Bridge [MEDV] (0000:fe)
ACPI: PCI Root Bridge [S0H0] (0000:00)
PCI quirk: region 0d00-0d7f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0e80-0ebf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *12
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *12
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *6 10 11 14 15)
ACPI: PCI Root Bridge [S0H1] (0000:02)
PCI: Enable I/O Space to 1 KB Granularity
PCI: Enable I/O Space to 1 KB Granularity
ACPI: PCI Root Bridge [S0H2] (0000:09)
PCI: Enable I/O Space to 1 KB Granularity
PCI: Enable I/O Space to 1 KB Granularity
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
(XEN) io_apic.c:2228:
(XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=4
(XEN) ioapic_guest_write: old_entry=000000f1, new_entry=000100f1
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
pnp: PnP ACPI: found 9 devices
xen_mem: Initialising balloon driver.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:1e.0
IO window: 1000-1fff
MEM window: f6000000-f7efffff
PREFETCH window: f0800000-f08fffff
PCI: Bridge: 0000:02:1d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:1f.0
IO window: 2000-23ff
MEM window: f4f00000-f4ffffff
PREFETCH window: f0a00000-f0bfffff
PCI: Bridge: 0000:09:1d.0
IO window: 2800-2bff
MEM window: f3f00000-f3ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:09:1f.0
IO window: disabled.
MEM window: f3e00000-f3efffff
PREFETCH window: f2e00000-f2ffffff
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
IA-32 Microcode Update Driver: v1.14a-xen <tigran@veritas.com>
audit: initializing netlink socket (disabled)
audit(1209985982.018:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Xen virtual console successfully installed as xvc0
Event-channel device installed.
netfront: Initialising virtual ethernet driver.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 176k freed
scsi_mod: no version for "struct_module" found: kernel tainted.
SCSI subsystem initialized
ICH4: IDE controller at PCI slot 0000:00:1f.1
GSI 16 sharing vector 0x98 and IRQ 16
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x0880-0x0887, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x0888-0x088f, BIOS settings: hdc:pio, hdd:pio
hda: _NEC DVD_RW ND-6750A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SAS Host driver 3.04.01
GSI 17 sharing vector 0xA0 and IRQ 17
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 48 (level, low) -> IRQ 17
mptbase: Initiating ioc0 bringup
ioc0: SAS1068: Capabilities={Initiator}
scsi0 : ioc0: LSISAS1068, FwRev=010a0000h, Ports=1, MaxQ=511, IRQ=17
Vendor: FUJITSU Model: MAY2073RC Rev: 0103
Type: Direct-Access ANSI SCSI revision: 03
Vendor: FUJITSU Model: MAY2073RC Rev: 0103
Type: Direct-Access ANSI SCSI revision: 03
Vendor: LSILOGIC Model: Logical Volume Rev: 3000
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 138670080 512-byte hdwr sectors (70999 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 138670080 512-byte hdwr sectors (70999 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda:<5>scsi 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:1:0: Attached scsi generic sg1 type 0
sda1 sda2 sda3
sd 0:1:0:0: Attached scsi disk sda
sd 0:1:0:0: Attached scsi generic sg2 type 0
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
Adding 1052248k swap on /dev/disk/by-id/scsi-3600508e000000000ff4df9da7f80cc05-part2. Priority:-1 extents:1 across:1052248k
Fusion MPT misc device (ioctl) driver 3.04.01
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
GSI 18 sharing vector 0xA8 and IRQ 18
ACPI: PCI Interrupt 0000:0a:01.0[A] -> GSI 72 (level, low) -> IRQ 18
e1000: 0000:0a:01.0: e1000_probe: (PCI-X:133MHz:64-bit) 08:00:0b:1e:38:1c
usbcore: registered new driver usbfs
usbcore: registered new driver hub
GSI 19 sharing vector 0xB0 and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
USB Universal Host Controller Interface driver v3.0
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xf7fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
i8xx TCO timer: failed to reset NO_REBOOT flag, reboot disabled by hardware
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 20 sharing vector 0xB8 and IRQ 20
ACPI: PCI Interrupt 0000:0a:01.1[B] -> GSI 73 (level, low) -> IRQ 20
GSI 21 sharing vector 0xC0 and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 21, io base 0x00000800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
e1000: 0000:0a:01.1: e1000_probe: (PCI-X:133MHz:64-bit) 08:00:0b:1e:38:1d
intel_rng: FWH not detected
hub 2-0:1.0: 2 ports detected
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 22 sharing vector 0xC8 and IRQ 22
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 22, io base 0x00000820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00000840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
GSI 23 sharing vector 0xD0 and IRQ 23
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 23
GSI 24 sharing vector 0xD8 and IRQ 24
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 22 (level, low) -> IRQ 24
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[24] MMIO=[f7efe800-f7efefff] Max Packet=[2048] IR/IT contexts=[4/8]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: USBPS2 as /class/input/input0
usbcore: registered new driver usbmouse
/home/unisys/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
input: USBPS2 as /class/input/input1
input: USB HID v1.00 Keyboard [USBPS2] on usb-0000:00:1d.0-1
input: Unisys Corporation as /class/input/input2
input: USB HID v1.01 Keyboard [Unisys Corporation] on usb-0000:00:1d.1-1
input: Unisys Corporation as /class/input/input3
input: USB HID v1.01 Mouse [Unisys Corporation] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
/home/unisys/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usbkbd
/home/unisys/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
parted[2773] trap divide error rip:2b80a0f5d781 rsp:7fff09c8e1f0 error:0
ACPI: Power Button (FF) [PWRF]
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
device-mapper: multipath: version 1.0.4 loaded
audit(1210000409.537:2): audit_pid=3643 old=0 by auid=4294967295
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: port 1(peth0) entering disabled state
md: stopping all md devices.
Synchronizing SCSI cache for disk sda:
ACPI: PCI interrupt for device 0000:0a:01.1 disabled
ACPI: PCI interrupt for device 0000:0a:01.0 disabled
System halted.
(XEN) Domain 0 halted: halting machine.
[-- MARK -- Mon May 5 15:00:00 2008]
__ __ _____ _____ _ _ _
\ \/ /___ _ __ |___ / |___ / _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ '_ \ |_ \ |_ \ __| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
/ \ __/ | | | ___) | ___) |__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |____(_)____/ \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
(XEN) Xen version 3.3-unstable (root@site) (gcc version 4.1.2 20070115 (prerelease) (SUSE Linux)) Fri May 2 05:32:52 EDT 2008
(XEN) Latest ChangeSet: Thu May 01 16:38:56 2008 +0100 17557:64f790e90d3d
(XEN) Command line: com1=115200,8n1 apic_verbosity=debug console=com1,vga
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 2 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009d800 (usable)
(XEN) 000000000009d800 - 00000000000a0000 (reserved)
(XEN) 00000000000ce000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 0000000037e70000 (usable)
(XEN) 0000000037e70000 - 0000000037ed7000 (ACPI data)
(XEN) 0000000037ed7000 - 0000000037f00000 (ACPI NVS)
(XEN) 0000000037f00000 - 00000000f0000000 (usable)
(XEN) 00000000f8000000 - 00000000fec00000 (reserved)
(XEN) 00000000fffc0000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000001008000000 (usable)
(XEN) System RAM: 65407MB (66976820kB)
(XEN) ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f8650
(XEN) ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x06040000) @ 0x0000000037e7ddfa
(XEN) ACPI: FADT (v004 UNISYS ZORRO 0x06040000 PTL 0x00000008) @ 0x0000000037ed607c
(XEN) ACPI: OEM1 (v001 UNISYS OEM1 0x06040000 LTP 0x06040000) @ 0x0000000037ed6170
(XEN) ACPI: OEM2 (v001 UNISYS OEM2 0x06040000 LTP 0x06040000) @ 0x0000000037ed61a0
(XEN) ACPI: WSPT (v001 UNISYS WSPT 0x06040000 LTP 0x06040000) @ 0x0000000037ed6d9c
(XEN) ACPI: SRAT (v001 UNISYS SRAT 0x06040000 LTP 0x06040000) @ 0x0000000037ed6dc4
(XEN) ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x06040000) @ 0x0000000037ed6ec4
(XEN) ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x0000000037ed6fb0
(XEN) ACPI: DSDT (v001 Intel 870 SMP 0x06040000 MSFT 0x03000000) @ 0x0000000000000000
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-0000001008000000
(XEN) Xen heap: 12MB (12848kB)
(XEN) Domain heap initialised: DMA width 32 bits
(XEN) found SMP MP-table at 000f8680
(XEN) DMI present.
(XEN) UNISYS ES7000-ONE detected: force use of apic=bigsmp
(XEN) Using APIC driver bigsmp
(XEN) ACPI: PM-Timer IO Port: 0xd08
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[d04,0], pm1x_evt[d00,0]
(XEN) ACPI: wakeup_vec[37ed8fcc], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
(XEN) Processor #0 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
(XEN) Processor #4 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x08] enabled)
(XEN) Processor #8 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x0c] enabled)
(XEN) Processor #12 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
(XEN) Processor #2 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
(XEN) Processor #6 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x0a] enabled)
(XEN) Processor #10 15:6 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x0e] enabled)
(XEN) Processor #14 15:6 APIC version 20
(XEN) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: IOAPIC (id[0x08] address[0xfec02000] gsi_base[24])
(XEN) IOAPIC[1]: apic_id 8, version 32, address 0xfec02000, GSI 24-47
(XEN) ACPI: IOAPIC (id[0x09] address[0xfec03000] gsi_base[48])
(XEN) IOAPIC[2]: apic_id 9, version 32, address 0xfec03000, GSI 48-71
(XEN) ACPI: IOAPIC (id[0x0a] address[0xfec04000] gsi_base[72])
(XEN) IOAPIC[3]: apic_id 10, version 32, address 0xfec04000, GSI 72-95
(XEN) ACPI: IOAPIC (id[0x0b] address[0xfec05000] gsi_base[96])
(XEN) IOAPIC[4]: apic_id 11, version 32, address 0xfec05000, GSI 96-119
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Phys. Using 5 I/O APICs
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) mapped APIC to ffff828bfffff000 (fee00000)
(XEN) mapped IOAPIC to ffff828bffffe000 (fec00000)
(XEN) mapped IOAPIC to ffff828bffffd000 (fec02000)
(XEN) mapped IOAPIC to ffff828bffffc000 (fec03000)
(XEN) mapped IOAPIC to ffff828bffffb000 (fec04000)
(XEN) mapped IOAPIC to ffff828bffffa000 (fec05000)
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 3400.153 MHz processor.
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) HVM: VMX enabled
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU0: Thermal monitoring enabled
(XEN) CPU0: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Getting VERSION: 50014
(XEN) Getting VERSION: 50014
(XEN) Getting ID: 0
(XEN) Getting LVT0: 10700
(XEN) Getting LVT1: 10400
(XEN) masked ExtINT on CPU#0
(XEN) Booting processor 1/4 eip 8c000
(XEN) Initializing CPU#1
(XEN) masked ExtINT on CPU#1
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 1
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU1: Thermal monitoring enabled
(XEN) CPU1: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 2/8 eip 8c000
(XEN) Initializing CPU#2
(XEN) masked ExtINT on CPU#2
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 2
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU2: Thermal monitoring enabled
(XEN) CPU2: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 3/12 eip 8c000
(XEN) Initializing CPU#3
(XEN) masked ExtINT on CPU#3
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 3
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU3: Thermal monitoring enabled
(XEN) CPU3: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 4/2 eip 8c000
(XEN) Initializing CPU#4
(XEN) masked ExtINT on CPU#4
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#4.
(XEN) CPU4: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU4: Thermal monitoring enabled
(XEN) CPU4: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 5/6 eip 8c000
(XEN) Initializing CPU#5
(XEN) masked ExtINT on CPU#5
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 1
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#5.
(XEN) CPU5: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU5: Thermal monitoring enabled
(XEN) CPU5: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 6/10 eip 8c000
(XEN) Initializing CPU#6
(XEN) masked ExtINT on CPU#6
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 2
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#6.
(XEN) CPU6: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU6: Thermal monitoring enabled
(XEN) CPU6: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Booting processor 7/14 eip 8c000
(XEN) Initializing CPU#7
(XEN) masked ExtINT on CPU#7
(XEN) CPU: Trace cache: 12K uops, L1 D cache: 16K
(XEN) CPU: L2 cache: 1024K
(XEN) CPU: L3 cache: 16384K
(XEN) CPU: Physical Processor ID: 3
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check architecture supported.
(XEN) Intel machine check reporting enabled on CPU#7.
(XEN) CPU7: Intel P4/Xeon Extended MCE MSRs (24) available
(XEN) CPU7: Thermal monitoring enabled
(XEN) CPU7: Intel Genuine Intel(R) CPU 3.40GHz stepping 08
(XEN) Total of 8 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) init IO_APIC IRQs
(XEN) IO-APIC (apicid-pin) 0-0, 0-16, 0-17, 0-18, 0-19, 0-20, 0-21, 0-22, 0-23, 8-0, 8-1, 8-2, 8-3, 8-4, 8-5, 8-6, 8-7, 8-8, 8-9, 8-10, 8-11, 8-12, 8-13, 8-14, 8-15, 8-16, 8-17, 8-18, 8-19, 8-20, 8-21, 8-22, 8-23, 9-0, 9-1, 9-2, 9-3, 9-4, 9-5, 9-6, 9-7, 9-8, 9-9, 9-10, 9-11, 9-12, 9-13, 9-14, 9-15, 9-16, 9-17, 9-18, 9-19, 9-20, 9-21, 9-22, 9-23, 10-0, 10-1, 10-2, 10-3, 10-4, 10-5, 10-6, 10-7, 10-8, 10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15, 10-16, 10-17, 10-18, 10-19, 10-20, 10-21, 10-22, 10-23, 11-0, 11-1, 11-2, 11-3, 11-4, 11-5, 11-6, 11-7, 11-8, 11-9, 11-10, 11-11, 11-12, 11-13, 11-14, 11-15, 11-16, 11-17, 11-18, 11-19, 11-20, 11-21, 11-22, 11-23 not connected.
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=0 pin2=0
(XEN) number of MP IRQ sources: 15.
(XEN) number of IO-APIC #0 registers: 24.
(XEN) number of IO-APIC #8 registers: 24.
(XEN) number of IO-APIC #9 registers: 24.
(XEN) number of IO-APIC #10 registers: 24.
(XEN) number of IO-APIC #11 registers: 24.
(XEN) testing the IO APIC.......................
(XEN) IO APIC #0......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 0 0 0 0 0 0 0 28
(XEN) 02 000 00 0 0 0 0 0 0 0 F0
(XEN) 03 000 00 0 0 0 0 0 0 0 30
(XEN) 04 000 00 0 0 0 0 0 0 0 F1
(XEN) 05 000 00 0 0 0 0 0 0 0 38
(XEN) 06 000 00 0 0 0 0 0 0 0 40
(XEN) 07 000 00 0 0 0 0 0 0 0 48
(XEN) 08 000 00 0 0 0 0 0 0 0 50
(XEN) 09 000 00 1 1 0 0 0 0 0 58
(XEN) 0a 000 00 0 0 0 0 0 0 0 60
(XEN) 0b 000 00 0 0 0 0 0 0 0 68
(XEN) 0c 000 00 0 0 0 0 0 0 0 70
(XEN) 0d 000 00 0 0 0 0 0 0 0 78
(XEN) 0e 000 00 0 0 0 0 0 0 0 88
(XEN) 0f 000 00 0 0 0 0 0 0 0 90
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #8......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #9......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #10......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) IO APIC #11......
(XEN) .... register #00: 00000000
(XEN) ....... : physical APIC id: 00
(XEN) ....... : Delivery Type: 0
(XEN) ....... : LTS : 0
(XEN) .... register #01: 00178020
(XEN) ....... : max redirection entries: 0017
(XEN) ....... : PRQ implemented: 1
(XEN) ....... : IO APIC version: 0020
(XEN) .... register #02: 00000000
(XEN) ....... : arbitration: 00
(XEN) .... register #03: 00000001
(XEN) ....... : Boot DT : 1
(XEN) .... IRQ redirection table:
(XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
(XEN) 00 000 00 1 0 0 0 0 0 0 00
(XEN) 01 000 00 1 0 0 0 0 0 0 00
(XEN) 02 000 00 1 0 0 0 0 0 0 00
(XEN) 03 000 00 1 0 0 0 0 0 0 00
(XEN) 04 000 00 1 0 0 0 0 0 0 00
(XEN) 05 000 00 1 0 0 0 0 0 0 00
(XEN) 06 000 00 1 0 0 0 0 0 0 00
(XEN) 07 000 00 1 0 0 0 0 0 0 00
(XEN) 08 000 00 1 0 0 0 0 0 0 00
(XEN) 09 000 00 1 0 0 0 0 0 0 00
(XEN) 0a 000 00 1 0 0 0 0 0 0 00
(XEN) 0b 000 00 1 0 0 0 0 0 0 00
(XEN) 0c 000 00 1 0 0 0 0 0 0 00
(XEN) 0d 000 00 1 0 0 0 0 0 0 00
(XEN) 0e 000 00 1 0 0 0 0 0 0 00
(XEN) 0f 000 00 1 0 0 0 0 0 0 00
(XEN) 10 000 00 1 0 0 0 0 0 0 00
(XEN) 11 000 00 1 0 0 0 0 0 0 00
(XEN) 12 000 00 1 0 0 0 0 0 0 00
(XEN) 13 000 00 1 0 0 0 0 0 0 00
(XEN) 14 000 00 1 0 0 0 0 0 0 00
(XEN) 15 000 00 1 0 0 0 0 0 0 00
(XEN) 16 000 00 1 0 0 0 0 0 0 00
(XEN) 17 000 00 1 0 0 0 0 0 0 00
(XEN) Using vector-based indexing
(XEN) IRQ to pin mappings:
(XEN) IRQ240 -> 0:2
(XEN) IRQ40 -> 0:1
(XEN) IRQ48 -> 0:3
(XEN) IRQ241 -> 0:4
(XEN) IRQ56 -> 0:5
(XEN) IRQ64 -> 0:6
(XEN) IRQ72 -> 0:7
(XEN) IRQ80 -> 0:8
(XEN) IRQ88 -> 0:9
(XEN) IRQ96 -> 0:10
(XEN) IRQ104 -> 0:11
(XEN) IRQ112 -> 0:12
(XEN) IRQ120 -> 0:13
(XEN) IRQ136 -> 0:14
(XEN) IRQ144 -> 0:15
(XEN) .................................... done.
(XEN) Using local APIC timer interrupts.
(XEN) calibrating APIC timer ...
(XEN) ..... CPU clock speed is 3399.9940 MHz.
(XEN) ..... host bus clock speed is 199.9995 MHz.
(XEN) ..... bus_scale = 0x0000CCCC
(XEN) checking TSC synchronization across 8 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
(XEN) Brought up 8 CPUs
(XEN) I/O virtualisation disabled
(XEN) <PM> ACPI (supports S3)
(XEN) Machine check exception polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x2628e8
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80463000 memsz=0x8b948
(XEN) elf_parse_binary: phdr: paddr=0xffffffff804ef000 memsz=0xc08
(XEN) elf_parse_binary: phdr: paddr=0xffffffff804f0000 memsz=0xce58c
(XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff805be58c
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: FEATURES = "writable_page_tables|writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|supervisor_mode_kernel"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_parse: using notes from SHT_NOTE section
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0xffffffff80000000
(XEN) virt_offset = 0x0
(XEN) virt_kstart = 0xffffffff80200000
(XEN) virt_kend = 0xffffffff805be58c
(XEN) virt_entry = 0xffffffff80200000
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 -> 0xffffffff805be58c
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000fc0000000->0000000fd0000000 (16427225 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80200000->ffffffff805be58c
(XEN) Init. ramdisk: ffffffff805bf000->ffffffff80cdf800
(XEN) Phys-Mach map: ffffffff80ce0000->ffffffff88ab46c8
(XEN) Start info: ffffffff88ab5000->ffffffff88ab54a4
(XEN) Page tables: ffffffff88ab6000->ffffffff88aff000
(XEN) Boot stack: ffffffff88aff000->ffffffff88b00000
(XEN) TOTAL: ffffffff80000000->ffffffff88c00000
(XEN) ENTRY ADDRESS: ffffffff80200000
(XEN) Dom0 has maximum 8 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff804628e8
(XEN) elf_load_binary: phdr 1 at 0xffffffff80463000 -> 0xffffffff804ee948
(XEN) elf_load_binary: phdr 2 at 0xffffffff804ef000 -> 0xffffffff804efc08
(XEN) elf_load_binary: phdr 3 at 0xffffffff804f0000 -> 0xffffffff8052a108
(XEN) Initrd len 0x720800, start at 0xffffffff805bf000
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 120kB init memory.
kernel direct mapping tables up to fbb0d9000 @ 8b3e000-10957000
Bootdata ok (command line is root=/dev/disk/by-id/scsi-3600508e000000000ff4df9da7f80cc05-part1 vga=0x314 resume=/dev/sda2 splash=silent showopts debug=y )
Linux version 2.6.18.8-xen (root@m0075-p0) (gcc version 4.1.2 20070115 (prerelease) (SUSE Linux)) #1 SMP Fri May 2 06:05:38 EDT 2008
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000fbb0d9000 (usable)
DMI present.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x08] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x0c] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x0a] enabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x0e] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x08] address[0xfec02000] gsi_base[24])
IOAPIC[1]: apic_id 8, version 32, address 0xfec02000, GSI 24-47
ACPI: IOAPIC (id[0x09] address[0xfec03000] gsi_base[48])
IOAPIC[2]: apic_id 9, version 32, address 0xfec03000, GSI 48-71
ACPI: IOAPIC (id[0x0a] address[0xfec04000] gsi_base[72])
IOAPIC[3]: apic_id 10, version 32, address 0xfec04000, GSI 72-95
ACPI: IOAPIC (id[0x0b] address[0xfec05000] gsi_base[96])
IOAPIC[4]: apic_id 11, version 32, address 0xfec05000, GSI 96-119
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at f0800000 (gap: f0000000:8000000)
Built 1 zonelists. Total pages: 16269295
Kernel command line: root=/dev/disk/by-id/scsi-3600508e000000000ff4df9da7f80cc05-part1 vga=0x314 resume=/dev/sda2 splash=silent showopts debug=y
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 35955.456 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes)
Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes)
Software IO TLB enabled:
Aperture: 64 megabytes
Kernel range: ffff88004fa51000 - ffff880053a51000
Address size: 27 bits
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Memory: 64631228k/65979236k available (2025k kernel code, 1339076k reserved, 891k data, 176k init)
Calibrating delay using timer specific routine.. 72250.18 BogoMIPS (lpj=361250926)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
SMP alternatives: switching to SMP code
Initializing CPU#1
Initializing CPU#2
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Initializing CPU#3
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
Initializing CPU#4
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Initializing CPU#5
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Initializing CPU#6
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
Brought up 8 CPUs
Initializing CPU#7
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: L3 cache: 16384K
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
Timer ISR/0: Time went backwards: delta=-2679966594 delta_cpu=10033406 shadow=13664567457 off=530033587 processed=16874567457 cpu_processed=14184567457
0: 14184567457
1: 16874567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2679669267 delta_cpu=10330733 shadow=13664567457 off=540330897 processed=16884567457 cpu_processed=14194567457
0: 14194567457
1: 16884567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2679669090 delta_cpu=10330910 shadow=13664567457 off=550331029 processed=16894567457 cpu_processed=14204567457
0: 14204567457
1: 16894567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689669181 delta_cpu=10330819 shadow=13664567457 off=560330957 processed=16914567457 cpu_processed=14214567457
0: 14214567457
1: 16914567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689656200 delta_cpu=10343800 shadow=13664567457 off=570343934 processed=16924567457 cpu_processed=14224567457
0: 14224567457
1: 16924567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689656561 delta_cpu=10343439 shadow=13664567457 off=580343540 processed=16934567457 cpu_processed=14234567457
0: 14234567457
1: 16934567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689656806 delta_cpu=10343194 shadow=13664567457 off=590343294 processed=16944567457 cpu_processed=14244567457
0: 14244567457
1: 16944567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689604641 delta_cpu=10395359 shadow=13664567457 off=600395494 processed=16954567457 cpu_processed=14254567457
0: 14254567457
1: 16954567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689585212 delta_cpu=10414788 shadow=13664567457 off=610414889 processed=16964567457 cpu_processed=14264567457
0: 14264567457
1: 16964567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
Timer ISR/0: Time went backwards: delta=-2689204033 delta_cpu=10795967 shadow=13664567457 off=620796078 processed=16974567457 cpu_processed=14274567457
0: 14274567457
1: 16974567457
2: 16874567457
3: 16874567457
4: 16874567457
5: 16874567457
6: 16874567457
7: 16874567457
migration_cost=752
checking if image is initramfs... it is
Freeing initrd memory: 7298k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: Device [MBDV] status [00000008]: functional but not present; setting present
ACPI: PCI Root Bridge [MBDV] (0000:ff)
ACPI: Device [MEDV] status [00000008]: functional but not present; setting present
ACPI: PCI Root Bridge [MEDV] (0000:fe)
ACPI: PCI Root Bridge [S0H0] (0000:00)
PCI quirk: region 0d00-0d7f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0e80-0ebf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *12
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *12
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *6 10 11 14 15)
ACPI: PCI Root Bridge [S0H1] (0000:02)
PCI: Enable I/O Space to 1 KB Granularity
PCI: Enable I/O Space to 1 KB Granularity
ACPI: PCI Root Bridge [S0H2] (0000:09)
PCI: Enable I/O Space to 1 KB Granularity
PCI: Enable I/O Space to 1 KB Granularity
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
(XEN) io_apic.c:2228:
(XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=4
(XEN) ioapic_guest_write: old_entry=000000f1, new_entry=000100f1
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
pnp: PnP ACPI: found 9 devices
xen_mem: Initialising balloon driver.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:1e.0
IO window: 1000-1fff
MEM window: f6000000-f7efffff
PREFETCH window: f0800000-f08fffff
PCI: Bridge: 0000:02:1d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:1f.0
IO window: 2000-23ff
MEM window: f4f00000-f4ffffff
PREFETCH window: f0a00000-f0bfffff
PCI: Bridge: 0000:09:1d.0
IO window: 2800-2bff
MEM window: f3f00000-f3ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:09:1f.0
IO window: disabled.
MEM window: f3e00000-f3efffff
PREFETCH window: f2e00000-f2ffffff
NET: Registered protocol family 2
printk: 10 messages suppressed.
Timer ISR/0: Time went backwards: delta=-481536872 delta_cpu=5458463128 shadow=22553026982 off=102491 processed=23034567457 cpu_processed=17094567457
0: 17094567457
1: 23034567457
2: 23034567457
3: 23034567457
4: 23034567457
5: 23034567457
6: 23034567457
7: 23034567457
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
IA-32 Microcode Update Driver: v1.14a-xen <tigran@veritas.com>
audit: initializing netlink socket (disabled)
audit(1209987391.294:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0689): AE_NOT_FOUND, Processor Device is not present [20060707]
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Xen virtual console successfully installed as xvc0
Event-channel device installed.
netfront: Initialising virtual ethernet driver.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 176k freed
scsi_mod: no version for "struct_module" found: kernel tainted.
SCSI subsystem initialized
ICH4: IDE controller at PCI slot 0000:00:1f.1
GSI 16 sharing vector 0x98 and IRQ 16
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x0880-0x0887, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x0888-0x088f, BIOS settings: hdc:pio, hdd:pio
hda: _NEC DVD_RW ND-6750A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
printk: 29 messages suppressed.
Timer ISR/7: Time went backwards: delta=-3932025029 delta_cpu=37974971 shadow=22005202525 off=1467350925 processed=27404567457 cpu_processed=23434567457
0: 27404567457
1: 23354567457
2: 23364567457
3: 23354567457
4: 23364567457
5: 23364567457
6: 23354567457
7: 23434567457
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SAS Host driver 3.04.01
GSI 17 sharing vector 0xA0 and IRQ 17
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 48 (level, low) -> IRQ 17
mptbase: Initiating ioc0 bringup
ioc0: SAS1068: Capabilities={Initiator}
printk: 6 messages suppressed.
Timer ISR/4: Time went backwards: delta=-20026810 delta_cpu=19973190 shadow=38917278574 off=17370776 processed=38954567457 cpu_processed=38914567457
0: 38954567457
1: 38924567457
2: 38924567457
3: 38924567457
4: 38914567457
5: 38924567457
6: 38924567457
7: 38924567457
Timer ISR/6: Time went backwards: delta=-10043350 delta_cpu=19956650 shadow=38932733611 off=11790810 processed=38954567457 cpu_processed=38924567457
0: 38954567457
1: 38924567457
2: 38924567457
3: 38924567457
4: 38924567457
5: 38924567457
6: 38924567457
7: 38924567457
scsi0 : ioc0: LSISAS1068, FwRev=010a0000h, Ports=1, MaxQ=511, IRQ=17
Vendor: FUJITSU Model: MAY2073RC Rev: 0103
Type: Direct-Access ANSI SCSI revision: 03
Vendor: FUJITSU Model: MAY2073RC Rev: 0103
Type: Direct-Access ANSI SCSI revision: 03
Vendor: LSILOGIC Model: Logical Volume Rev: 3000
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 138670080 512-byte hdwr sectors (70999 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 138670080 512-byte hdwr sectors (70999 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda:<5>scsi 0:0:0:0: Attached scsi generic sg0 type 0
sda1 sda2 sda3
scsi 0:0:1:0: Attached scsi generic sg1 type 0
sd 0:1:0:0: Attached scsi disk sda
sd 0:1:0:0: Attached scsi generic sg2 type 0
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
Adding 1052248k swap on /dev/disk/by-id/scsi-3600508e000000000ff4df9da7f80cc05-part2. Priority:-1 extents:1 across:1052248k
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
GSI 18 sharing vector 0xA8 and IRQ 18
ACPI: PCI Interrupt 0000:0a:01.0[A] -> GSI 72 (level, low) -> IRQ 18
GSI 19 sharing vector 0xB0 and IRQ 19
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 19
e1000: 0000:0a:01.0: e1000_probe: (PCI-X:133MHz:64-bit) 08:00:0b:1e:38:1c
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 20 sharing vector 0xB8 and IRQ 20
ACPI: PCI Interrupt 0000:0a:01.1[B] -> GSI 73 (level, low) -> IRQ 20
GSI 21 sharing vector 0xC0 and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xf7fffc00
Fusion MPT misc device (ioctl) driver 3.04.01
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
e1000: 0000:0a:01.1: e1000_probe: (PCI-X:133MHz:64-bit) 08:00:0b:1e:38:1d
i8xx TCO timer: failed to reset NO_REBOOT flag, reboot disabled by hardware
GSI 22 sharing vector 0xC8 and IRQ 22
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 22, io base 0x00000800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 23 sharing vector 0xD0 and IRQ 23
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 23, io base 0x00000820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00000840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
GSI 24 sharing vector 0xD8 and IRQ 24
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 22 (level, low) -> IRQ 24
usb 2-1: new low speed USB device using uhci_hcd and address 2
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[24] MMIO=[f7efe800-f7efefff] Max Packet=[2048] IR/IT contexts=[4/8]
usb 2-1: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
input: USBPS2 as /class/input/input0
usbcore: registered new driver usbmouse
/home/unisys/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usbcore: registered new driver hiddev
input: USBPS2 as /class/input/input1
input: USB HID v1.00 Keyboard [USBPS2] on usb-0000:00:1d.0-1
input: Unisys Corporation as /class/input/input2
input: USB HID v1.01 Keyboard [Unisys Corporation] on usb-0000:00:1d.1-1
input: Unisys Corporation as /class/input/input3
input: USB HID v1.01 Mouse [Unisys Corporation] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
/home/unisys/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usbkbd
/home/unisys/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
parted[2798] trap divide error rip:2b05fd0de781 rsp:7fffadb0bd90 error:0
ACPI: Power Button (FF) [PWRF]
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
device-mapper: multipath: version 1.0.4 loaded
audit(1210001914.593:2): audit_pid=3661 old=0 by auid=4294967295
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
[-- Attachment #3: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: Time went backwards errors booting unstable cs 17557 with 64GB memory
2008-05-06 15:16 Time went backwards errors booting unstable cs 17557 with 64GB memory Carb, Brian A
@ 2008-05-06 15:30 ` Keir Fraser
2008-05-06 15:40 ` Bill Burns
1 sibling, 0 replies; 5+ messages in thread
From: Keir Fraser @ 2008-05-06 15:30 UTC (permalink / raw)
To: Carb, Brian A, xen-devel
You'll probably have to binary chop to find the offending changeset. All
sorts of stuff has gone in since c/s 17318.
-- Keir
On 6/5/08 16:16, "Carb, Brian A" <Brian.Carb@unisys.com> wrote:
> I've built the latest xen unstable cs 17557 to run on a multi-cell
> ES7000/one. When I boot with the procs and memory from a single cell (4
> cores aka 8 cpus from cell0, 32gb memory from cell0), dom0 boots cleanly
> . However, if I use the memory from 2 cells (4 cores aka 8 cpus from
> cell0, 64gb memory interleaved from cell0 & cell1), dom0 boots
> eventually, but produces multiple Timer errors as shown below. I tried
> setting numa=on but timer errors persist. FYI Xen unstable cs 17318 ran
> successfully without timer errors on this multi-cell configuration.
>
> Timer ISR/0: Time went backwards: delta=-2679966594 delta_cpu=10033406
> shadow=13664567457 off=530033587 processed=16874567457
> cpu_processed=14184567457
> 0: 14184567457
> 1: 16874567457
> 2: 16874567457
> 3: 16874567457
> 4: 16874567457
> 5: 16874567457
> 6: 16874567457
> 7: 16874567457
>
> The attached serial trace shows a boot with 32gb and then a boot with
> 64gb.
>
> brian carb
> unisys corporation - malvern, pa
>
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Time went backwards errors booting unstable cs 17557 with 64GB memory
2008-05-06 15:16 Time went backwards errors booting unstable cs 17557 with 64GB memory Carb, Brian A
2008-05-06 15:30 ` Keir Fraser
@ 2008-05-06 15:40 ` Bill Burns
2008-05-06 17:21 ` Time went backwards errors booting unstable cs 17557with " Carb, Brian A
1 sibling, 1 reply; 5+ messages in thread
From: Bill Burns @ 2008-05-06 15:40 UTC (permalink / raw)
To: Carb, Brian A; +Cc: xen-devel
Carb, Brian A wrote:
> I've built the latest xen unstable cs 17557 to run on a multi-cell
> ES7000/one. When I boot with the procs and memory from a single cell (4
> cores aka 8 cpus from cell0, 32gb memory from cell0), dom0 boots cleanly
> . However, if I use the memory from 2 cells (4 cores aka 8 cpus from
> cell0, 64gb memory interleaved from cell0 & cell1), dom0 boots
> eventually, but produces multiple Timer errors as shown below. I tried
> setting numa=on but timer errors persist. FYI Xen unstable cs 17318 ran
> successfully without timer errors on this multi-cell configuration.
>
> Timer ISR/0: Time went backwards: delta=-2679966594 delta_cpu=10033406
> shadow=13664567457 off=530033587 processed=16874567457
> cpu_processed=14184567457
> 0: 14184567457
> 1: 16874567457
> 2: 16874567457
> 3: 16874567457
> 4: 16874567457
> 5: 16874567457
> 6: 16874567457
> 7: 16874567457
>
> The attached serial trace shows a boot with 32gb and then a boot with
> 64gb.
>
Is the system using the pm timer? You may try clocksource=pit,
or keeping more memory in the Hypervisor (via xenheap or dom0_mem)
as workarounds.
Bill
> brian carb
> unisys corporation - malvern, pa
>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: Time went backwards errors booting unstable cs 17557with 64GB memory
2008-05-06 15:40 ` Bill Burns
@ 2008-05-06 17:21 ` Carb, Brian A
2008-05-06 17:31 ` Bill Burns
0 siblings, 1 reply; 5+ messages in thread
From: Carb, Brian A @ 2008-05-06 17:21 UTC (permalink / raw)
To: Bill Burns; +Cc: xen-devel
Setting clocksource=pit removes the errors and allows a clean boot, as
does setting dom0_mem=4096M. What are the implications of running with
a different clocksource?
FYI setting xenheap_megabytes=64 by itself does not eliminate the timer
errors..
brian carb
unisys corporation - malvern, pa
-----Original Message-----
From: Bill Burns [mailto:bburns@redhat.com]
Sent: Tuesday, May 06, 2008 11:40 AM
To: Carb, Brian A
Cc: xen-devel
Subject: Re: [Xen-devel] Time went backwards errors booting unstable cs
17557with 64GB memory
Carb, Brian A wrote:
> I've built the latest xen unstable cs 17557 to run on a multi-cell
> ES7000/one. When I boot with the procs and memory from a single cell
> (4 cores aka 8 cpus from cell0, 32gb memory from cell0), dom0 boots
> cleanly . However, if I use the memory from 2 cells (4 cores aka 8
> cpus from cell0, 64gb memory interleaved from cell0 & cell1), dom0
> boots eventually, but produces multiple Timer errors as shown below. I
> tried setting numa=on but timer errors persist. FYI Xen unstable cs
> 17318 ran successfully without timer errors on this multi-cell
configuration.
>
> Timer ISR/0: Time went backwards: delta=-2679966594 delta_cpu=10033406
> shadow=13664567457 off=530033587 processed=16874567457
> cpu_processed=14184567457
> 0: 14184567457
> 1: 16874567457
> 2: 16874567457
> 3: 16874567457
> 4: 16874567457
> 5: 16874567457
> 6: 16874567457
> 7: 16874567457
>
> The attached serial trace shows a boot with 32gb and then a boot with
> 64gb.
>
Is the system using the pm timer? You may try clocksource=pit, or
keeping more memory in the Hypervisor (via xenheap or dom0_mem) as
workarounds.
Bill
> brian carb
> unisys corporation - malvern, pa
>
>
>
>
> ----------------------------------------------------------------------
> --
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Time went backwards errors booting unstable cs 17557with 64GB memory
2008-05-06 17:21 ` Time went backwards errors booting unstable cs 17557with " Carb, Brian A
@ 2008-05-06 17:31 ` Bill Burns
0 siblings, 0 replies; 5+ messages in thread
From: Bill Burns @ 2008-05-06 17:31 UTC (permalink / raw)
To: Carb, Brian A; +Cc: xen-devel
Carb, Brian A wrote:
>
> Setting clocksource=pit removes the errors and allows a clean boot, as
> does setting dom0_mem=4096M. What are the implications of running with
> a different clocksource?
>
Good question. What appears to be happening is that the
initial calibration is bad. If dom0 is started before
a second calibration occurs it's gets the speed of CPU0
wrong and bad things happen. Delaying the start of
dom0 by giving the hypervisor more memory to scrub allows
for a second calibration. Why PIT works I really don't
know.
The suspicion is that somehow the calibration code
has an issue when there is a long outage, as in starting
up a bunch of other CPUs, before the first calibration.
But that is just a guess at this point. There is a bug
there that needs to be fixed.
Bill
> FYI setting xenheap_megabytes=64 by itself does not eliminate the timer
> errors..
>
> brian carb
> unisys corporation - malvern, pa
>
> -----Original Message-----
> From: Bill Burns [mailto:bburns@redhat.com]
> Sent: Tuesday, May 06, 2008 11:40 AM
> To: Carb, Brian A
> Cc: xen-devel
> Subject: Re: [Xen-devel] Time went backwards errors booting unstable cs
> 17557with 64GB memory
>
> Carb, Brian A wrote:
>> I've built the latest xen unstable cs 17557 to run on a multi-cell
>> ES7000/one. When I boot with the procs and memory from a single cell
>> (4 cores aka 8 cpus from cell0, 32gb memory from cell0), dom0 boots
>> cleanly . However, if I use the memory from 2 cells (4 cores aka 8
>> cpus from cell0, 64gb memory interleaved from cell0 & cell1), dom0
>> boots eventually, but produces multiple Timer errors as shown below. I
>
>> tried setting numa=on but timer errors persist. FYI Xen unstable cs
>> 17318 ran successfully without timer errors on this multi-cell
> configuration.
>> Timer ISR/0: Time went backwards: delta=-2679966594 delta_cpu=10033406
>> shadow=13664567457 off=530033587 processed=16874567457
>> cpu_processed=14184567457
>> 0: 14184567457
>> 1: 16874567457
>> 2: 16874567457
>> 3: 16874567457
>> 4: 16874567457
>> 5: 16874567457
>> 6: 16874567457
>> 7: 16874567457
>>
>> The attached serial trace shows a boot with 32gb and then a boot with
>> 64gb.
>>
>
> Is the system using the pm timer? You may try clocksource=pit, or
> keeping more memory in the Hypervisor (via xenheap or dom0_mem) as
> workarounds.
>
> Bill
>
>> brian carb
>> unisys corporation - malvern, pa
>>
>>
>>
>>
>> ----------------------------------------------------------------------
>> --
>>
>> _______________________________________________
>> Xen-devel mailing list
>> Xen-devel@lists.xensource.com
>> http://lists.xensource.com/xen-devel
>
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2008-05-06 17:31 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-05-06 15:16 Time went backwards errors booting unstable cs 17557 with 64GB memory Carb, Brian A
2008-05-06 15:30 ` Keir Fraser
2008-05-06 15:40 ` Bill Burns
2008-05-06 17:21 ` Time went backwards errors booting unstable cs 17557with " Carb, Brian A
2008-05-06 17:31 ` Bill Burns
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.