* [linux-dvb] Smit CAM problems
@ 2008-06-12 4:12 Vladimir Prudnikov
[not found] ` <485100C3.2090908@sttcr.org>
0 siblings, 1 reply; 7+ messages in thread
From: Vladimir Prudnikov @ 2008-06-12 4:12 UTC (permalink / raw)
To: Linux DVB Mailing List
Hello!
I'm using SMIT cams to descramble channels on TT S-1500 and TT-
S2-3200. After some time of normal operation SMIT cams drop out and
stop decrypting the stream. It needs to be removed from the CI slot
and reinserted to resume normal operation. Aston CAMs have no such
problems, but they don't support 0x652 Irdeto.
I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). Same
problem everywhere.
Regards,
Vladimir
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 7+ messages in thread[parent not found: <485100C3.2090908@sttcr.org>]
* Re: [linux-dvb] Smit CAM problems [not found] ` <485100C3.2090908@sttcr.org> @ 2008-06-12 12:51 ` Vladimir Prudnikov 2008-06-12 13:26 ` Frederic CAND 0 siblings, 1 reply; 7+ messages in thread From: Vladimir Prudnikov @ 2008-06-12 12:51 UTC (permalink / raw) To: Linux DVB Mailing List Didn't try Aston CAMs with mpeg4. But they do up to 12 channels of mpeg2 perfectly well. With no problems at all. SMiTs that are for 8 services can do only 3 to 4 for me. I think it's some kind of a driver bug because it begins working after reinitialisation. Doesn't get hot. I have tried to call Aston as well but with no success yet. Regards, Vladimir On Jun 12, 2008, at 2:56 PM, dan.lita@sttcr.org wrote: > Dear Vladimir, > > I read your post on linux-dvb list. We have an Aston Viaccess > Professional 2.15 CAM . > I read that you also use Aston CAMS. My question is whether your > Aston Viaccess cam can descramble H264 feeds or not? > We have tried on a PACE HDTV receiver and a Tandberg unit and it > does not descramble the H264 video pid. (black screen) > This does not happen with Viaccess RED cam. > > On older Common interface adapters from Technotrend, the one for TT > Premium DVB-S card, there was a jumper for 3V or 5V cam operation. > I assume the new CI adapter does not have such jumper. If it still > exist maybe it will be a good idea to switch from one voltage to the > other. > Another solution is to test whether it works or not for Irdeto to > use an Alphacrypt Classic CAM which, at least in theory, according > to MASCOM, supports Irdeto. > The third thing is to notice whether the SMIT cam gets hot in > operation. If it gets too hot maybe a fan similar to the one for > graphics card must be put near the Common interface adapter. > > BTW. Do you have any e-mail address from Aston? I have tried to > contact them but there is no e-mail address in their website. > > Best regards, > Dan Lita > > > Vladimir Prudnikov wrote: >> Hello! >> >> I'm using SMIT cams to descramble channels on TT S-1500 and TT- >> S2-3200. After some time of normal operation SMIT cams drop out >> and stop decrypting the stream. It needs to be removed from the CI >> slot and reinserted to resume normal operation. Aston CAMs have no >> such problems, but they don't support 0x652 Irdeto. >> I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). >> Same problem everywhere. >> >> Regards, >> Vladimir >> >> _______________________________________________ >> linux-dvb mailing list >> linux-dvb@linuxtv.org >> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >> >> >> > _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [linux-dvb] Smit CAM problems 2008-06-12 12:51 ` Vladimir Prudnikov @ 2008-06-12 13:26 ` Frederic CAND 2008-06-12 16:18 ` Vladimir Prudnikov 0 siblings, 1 reply; 7+ messages in thread From: Frederic CAND @ 2008-06-12 13:26 UTC (permalink / raw) To: Vladimir Prudnikov; +Cc: Linux DVB Mailing List Did you try to contact SMIT support ? Vladimir Prudnikov a écrit : > Didn't try Aston CAMs with mpeg4. But they do up to 12 channels of > mpeg2 perfectly well. With no problems at all. SMiTs that are for 8 > services can do only 3 to 4 for me. > I think it's some kind of a driver bug because it begins working after > reinitialisation. Doesn't get hot. I have tried to call Aston as well > but with no success yet. > > Regards, > Vladimir > > On Jun 12, 2008, at 2:56 PM, dan.lita@sttcr.org wrote: > >> Dear Vladimir, >> >> I read your post on linux-dvb list. We have an Aston Viaccess >> Professional 2.15 CAM . >> I read that you also use Aston CAMS. My question is whether your >> Aston Viaccess cam can descramble H264 feeds or not? >> We have tried on a PACE HDTV receiver and a Tandberg unit and it >> does not descramble the H264 video pid. (black screen) >> This does not happen with Viaccess RED cam. >> >> On older Common interface adapters from Technotrend, the one for TT >> Premium DVB-S card, there was a jumper for 3V or 5V cam operation. >> I assume the new CI adapter does not have such jumper. If it still >> exist maybe it will be a good idea to switch from one voltage to the >> other. >> Another solution is to test whether it works or not for Irdeto to >> use an Alphacrypt Classic CAM which, at least in theory, according >> to MASCOM, supports Irdeto. >> The third thing is to notice whether the SMIT cam gets hot in >> operation. If it gets too hot maybe a fan similar to the one for >> graphics card must be put near the Common interface adapter. >> >> BTW. Do you have any e-mail address from Aston? I have tried to >> contact them but there is no e-mail address in their website. >> >> Best regards, >> Dan Lita >> >> >> Vladimir Prudnikov wrote: >>> Hello! >>> >>> I'm using SMIT cams to descramble channels on TT S-1500 and TT- >>> S2-3200. After some time of normal operation SMIT cams drop out >>> and stop decrypting the stream. It needs to be removed from the CI >>> slot and reinserted to resume normal operation. Aston CAMs have no >>> such problems, but they don't support 0x652 Irdeto. >>> I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). >>> Same problem everywhere. >>> >>> Regards, >>> Vladimir >>> >>> _______________________________________________ >>> linux-dvb mailing list >>> linux-dvb@linuxtv.org >>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>> >>> >>> > > > _______________________________________________ > linux-dvb mailing list > linux-dvb@linuxtv.org > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > -- CAND Frederic Product Manager ANEVIA _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [linux-dvb] Smit CAM problems 2008-06-12 13:26 ` Frederic CAND @ 2008-06-12 16:18 ` Vladimir Prudnikov 2008-06-12 17:53 ` Dan Lita 0 siblings, 1 reply; 7+ messages in thread From: Vladimir Prudnikov @ 2008-06-12 16:18 UTC (permalink / raw) To: Frederic CAND; +Cc: Linux DVB Mailing List Do you think SMiT will be interested in hunting for bugs in linux drivers? These modules apparently work fine with any other hardware (I'm sure professional ones do!) Regards, Vladimir On Jun 12, 2008, at 5:26 PM, Frederic CAND wrote: > Did you try to contact SMIT support ? > > Vladimir Prudnikov a écrit : >> Didn't try Aston CAMs with mpeg4. But they do up to 12 channels of >> mpeg2 perfectly well. With no problems at all. SMiTs that are for >> 8 services can do only 3 to 4 for me. >> I think it's some kind of a driver bug because it begins working >> after reinitialisation. Doesn't get hot. I have tried to call >> Aston as well but with no success yet. >> Regards, >> Vladimir >> On Jun 12, 2008, at 2:56 PM, dan.lita@sttcr.org wrote: >>> Dear Vladimir, >>> >>> I read your post on linux-dvb list. We have an Aston Viaccess >>> Professional 2.15 CAM . >>> I read that you also use Aston CAMS. My question is whether your >>> Aston Viaccess cam can descramble H264 feeds or not? >>> We have tried on a PACE HDTV receiver and a Tandberg unit and it >>> does not descramble the H264 video pid. (black screen) >>> This does not happen with Viaccess RED cam. >>> >>> On older Common interface adapters from Technotrend, the one for >>> TT Premium DVB-S card, there was a jumper for 3V or 5V cam >>> operation. >>> I assume the new CI adapter does not have such jumper. If it >>> still exist maybe it will be a good idea to switch from one >>> voltage to the other. >>> Another solution is to test whether it works or not for Irdeto to >>> use an Alphacrypt Classic CAM which, at least in theory, >>> according to MASCOM, supports Irdeto. >>> The third thing is to notice whether the SMIT cam gets hot in >>> operation. If it gets too hot maybe a fan similar to the one for >>> graphics card must be put near the Common interface adapter. >>> >>> BTW. Do you have any e-mail address from Aston? I have tried to >>> contact them but there is no e-mail address in their website. >>> >>> Best regards, >>> Dan Lita >>> >>> >>> Vladimir Prudnikov wrote: >>>> Hello! >>>> >>>> I'm using SMIT cams to descramble channels on TT S-1500 and TT- >>>> S2-3200. After some time of normal operation SMIT cams drop out >>>> and stop decrypting the stream. It needs to be removed from the >>>> CI slot and reinserted to resume normal operation. Aston CAMs >>>> have no such problems, but they don't support 0x652 Irdeto. >>>> I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). >>>> Same problem everywhere. >>>> >>>> Regards, >>>> Vladimir >>>> >>>> _______________________________________________ >>>> linux-dvb mailing list >>>> linux-dvb@linuxtv.org >>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>>> >>>> >>>> >> _______________________________________________ >> linux-dvb mailing list >> linux-dvb@linuxtv.org >> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > -- > CAND Frederic > Product Manager > ANEVIA _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [linux-dvb] Smit CAM problems 2008-06-12 16:18 ` Vladimir Prudnikov @ 2008-06-12 17:53 ` Dan Lita 2008-06-12 18:16 ` Wolfgang Wegner 0 siblings, 1 reply; 7+ messages in thread From: Dan Lita @ 2008-06-12 17:53 UTC (permalink / raw) To: Vladimir Prudnikov, linux-dvb@linuxtv.org [-- Attachment #1.1: Type: text/plain, Size: 3814 bytes --] Dear Vladimir, I took a closer look on the CI-CAM adapter from Technotrend. There is a 3.3V voltage regulator (LM1117 DT 3.3V) Similar, on the AD-SP400 it seems to be also a 3.3V voltage regulator (marked 1084-33PE). 4046 board from Twinhan/Azurewave. According to SMIT operation voltage for their modules is 4.5 to 5.5V If in both cards the CAM takes power after these rectifiers you cannot have a guaranteed operation. Dan Vladimir Prudnikov wrote: > Do you think SMiT will be interested in hunting for bugs in linux > drivers? These modules apparently work fine with any other hardware > (I'm sure professional ones do!) > > Regards, > Vladimir > > On Jun 12, 2008, at 5:26 PM, Frederic CAND wrote: > > >> Did you try to contact SMIT support ? >> >> Vladimir Prudnikov a écrit : >> >>> Didn't try Aston CAMs with mpeg4. But they do up to 12 channels of >>> mpeg2 perfectly well. With no problems at all. SMiTs that are for >>> 8 services can do only 3 to 4 for me. >>> I think it's some kind of a driver bug because it begins working >>> after reinitialisation. Doesn't get hot. I have tried to call >>> Aston as well but with no success yet. >>> Regards, >>> Vladimir >>> On Jun 12, 2008, at 2:56 PM, dan.lita@sttcr.org wrote: >>> >>>> Dear Vladimir, >>>> >>>> I read your post on linux-dvb list. We have an Aston Viaccess >>>> Professional 2.15 CAM . >>>> I read that you also use Aston CAMS. My question is whether your >>>> Aston Viaccess cam can descramble H264 feeds or not? >>>> We have tried on a PACE HDTV receiver and a Tandberg unit and it >>>> does not descramble the H264 video pid. (black screen) >>>> This does not happen with Viaccess RED cam. >>>> >>>> On older Common interface adapters from Technotrend, the one for >>>> TT Premium DVB-S card, there was a jumper for 3V or 5V cam >>>> operation. >>>> I assume the new CI adapter does not have such jumper. If it >>>> still exist maybe it will be a good idea to switch from one >>>> voltage to the other. >>>> Another solution is to test whether it works or not for Irdeto to >>>> use an Alphacrypt Classic CAM which, at least in theory, >>>> according to MASCOM, supports Irdeto. >>>> The third thing is to notice whether the SMIT cam gets hot in >>>> operation. If it gets too hot maybe a fan similar to the one for >>>> graphics card must be put near the Common interface adapter. >>>> >>>> BTW. Do you have any e-mail address from Aston? I have tried to >>>> contact them but there is no e-mail address in their website. >>>> >>>> Best regards, >>>> Dan Lita >>>> >>>> >>>> Vladimir Prudnikov wrote: >>>> >>>>> Hello! >>>>> >>>>> I'm using SMIT cams to descramble channels on TT S-1500 and TT- >>>>> S2-3200. After some time of normal operation SMIT cams drop out >>>>> and stop decrypting the stream. It needs to be removed from the >>>>> CI slot and reinserted to resume normal operation. Aston CAMs >>>>> have no such problems, but they don't support 0x652 Irdeto. >>>>> I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). >>>>> Same problem everywhere. >>>>> >>>>> Regards, >>>>> Vladimir >>>>> >>>>> _______________________________________________ >>>>> linux-dvb mailing list >>>>> linux-dvb@linuxtv.org >>>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>>>> >>>>> >>>>> >>>>> >>> _______________________________________________ >>> linux-dvb mailing list >>> linux-dvb@linuxtv.org >>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>> >> -- >> CAND Frederic >> Product Manager >> ANEVIA >> > > > _______________________________________________ > linux-dvb mailing list > linux-dvb@linuxtv.org > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > [-- Attachment #1.2: Type: text/html, Size: 4777 bytes --] [-- Attachment #2: Type: text/plain, Size: 150 bytes --] _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [linux-dvb] Smit CAM problems 2008-06-12 17:53 ` Dan Lita @ 2008-06-12 18:16 ` Wolfgang Wegner 2008-06-18 16:06 ` Wolfgang Wegner 0 siblings, 1 reply; 7+ messages in thread From: Wolfgang Wegner @ 2008-06-12 18:16 UTC (permalink / raw) To: Dan Lita; +Cc: linux-dvb@linuxtv.org Hi Dan, according to the DVB (ETSI) specification, CAMs can only have 5V operating voltage. I do not know if there is any CAM around that (claims to) operate with 3.3V, although I know there are some that better should... Regards, Wolfgang On Thu, Jun 12, 2008 at 08:53:38PM +0300, Dan Lita wrote: > Dear Vladimir, > > I took a closer look on the CI-CAM adapter from Technotrend. > There is a 3.3V voltage regulator (LM1117 DT 3.3V) > > Similar, on the AD-SP400 it seems to be also a 3.3V voltage regulator > (marked 1084-33PE). 4046 board from Twinhan/Azurewave. > > According to SMIT operation voltage for their modules is 4.5 to 5.5V > > If in both cards the CAM takes power after these rectifiers > you cannot have a guaranteed operation. > > Dan > > Vladimir Prudnikov wrote: > >Do you think SMiT will be interested in hunting for bugs in linux > >drivers? These modules apparently work fine with any other hardware > >(I'm sure professional ones do!) > > > >Regards, > >Vladimir > > > >On Jun 12, 2008, at 5:26 PM, Frederic CAND wrote: > > > > > >>Did you try to contact SMIT support ? > >> > >>Vladimir Prudnikov a écrit : > >> > >>>Didn't try Aston CAMs with mpeg4. But they do up to 12 channels of > >>>mpeg2 perfectly well. With no problems at all. SMiTs that are for > >>>8 services can do only 3 to 4 for me. > >>>I think it's some kind of a driver bug because it begins working > >>>after reinitialisation. Doesn't get hot. I have tried to call > >>>Aston as well but with no success yet. > >>>Regards, > >>>Vladimir > >>>On Jun 12, 2008, at 2:56 PM, dan.lita@sttcr.org wrote: > >>> > >>>>Dear Vladimir, > >>>> > >>>>I read your post on linux-dvb list. We have an Aston Viaccess > >>>>Professional 2.15 CAM . > >>>>I read that you also use Aston CAMS. My question is whether your > >>>>Aston Viaccess cam can descramble H264 feeds or not? > >>>>We have tried on a PACE HDTV receiver and a Tandberg unit and it > >>>>does not descramble the H264 video pid. (black screen) > >>>>This does not happen with Viaccess RED cam. > >>>> > >>>>On older Common interface adapters from Technotrend, the one for > >>>>TT Premium DVB-S card, there was a jumper for 3V or 5V cam > >>>>operation. > >>>>I assume the new CI adapter does not have such jumper. If it > >>>>still exist maybe it will be a good idea to switch from one > >>>>voltage to the other. > >>>>Another solution is to test whether it works or not for Irdeto to > >>>>use an Alphacrypt Classic CAM which, at least in theory, > >>>>according to MASCOM, supports Irdeto. > >>>>The third thing is to notice whether the SMIT cam gets hot in > >>>>operation. If it gets too hot maybe a fan similar to the one for > >>>>graphics card must be put near the Common interface adapter. > >>>> > >>>>BTW. Do you have any e-mail address from Aston? I have tried to > >>>>contact them but there is no e-mail address in their website. > >>>> > >>>>Best regards, > >>>>Dan Lita > >>>> > >>>> > >>>>Vladimir Prudnikov wrote: > >>>> > >>>>>Hello! > >>>>> > >>>>>I'm using SMIT cams to descramble channels on TT S-1500 and TT- > >>>>>S2-3200. After some time of normal operation SMIT cams drop out > >>>>>and stop decrypting the stream. It needs to be removed from the > >>>>>CI slot and reinserted to resume normal operation. Aston CAMs > >>>>>have no such problems, but they don't support 0x652 Irdeto. > >>>>>I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). > >>>>>Same problem everywhere. > >>>>> > >>>>>Regards, > >>>>>Vladimir > >>>>> > >>>>>_______________________________________________ > >>>>>linux-dvb mailing list > >>>>>linux-dvb@linuxtv.org > >>>>>http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > >>>>> > >>>>> > >>>>> > >>>>> > >>>_______________________________________________ > >>>linux-dvb mailing list > >>>linux-dvb@linuxtv.org > >>>http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > >>> > >>-- > >>CAND Frederic > >>Product Manager > >>ANEVIA > >> > > > > > >_______________________________________________ > >linux-dvb mailing list > >linux-dvb@linuxtv.org > >http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > > > > > > _______________________________________________ > linux-dvb mailing list > linux-dvb@linuxtv.org > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [linux-dvb] Smit CAM problems 2008-06-12 18:16 ` Wolfgang Wegner @ 2008-06-18 16:06 ` Wolfgang Wegner 0 siblings, 0 replies; 7+ messages in thread From: Wolfgang Wegner @ 2008-06-18 16:06 UTC (permalink / raw) To: Dan Lita; +Cc: linux-dvb@linuxtv.org Hi again, I have to revise my claim a little bit: I just hit a problem with a "T-Rex SuperModule" that has VS1 tied low, thus signalling 3.3V power supply on the interface. However, this would not only violate the DVB spec, but is also contradictory to the "PC Card 5V" reading on the sticker... On a first try the module seems to work with 3.3V power supply, although I did not yet try descrambling anything with it because I do not have a smart card that can work with it. Regards, Wolfgang On Thu, Jun 12, 2008 at 08:16:59PM +0200, Wolfgang Wegner wrote: > Hi Dan, > > according to the DVB (ETSI) specification, CAMs can only have 5V operating > voltage. I do not know if there is any CAM around that (claims to) operate > with 3.3V, although I know there are some that better should... > > Regards, > Wolfgang > > On Thu, Jun 12, 2008 at 08:53:38PM +0300, Dan Lita wrote: > > Dear Vladimir, > > > > I took a closer look on the CI-CAM adapter from Technotrend. > > There is a 3.3V voltage regulator (LM1117 DT 3.3V) > > > > Similar, on the AD-SP400 it seems to be also a 3.3V voltage regulator > > (marked 1084-33PE). 4046 board from Twinhan/Azurewave. > > > > According to SMIT operation voltage for their modules is 4.5 to 5.5V > > > > If in both cards the CAM takes power after these rectifiers > > you cannot have a guaranteed operation. > > > > Dan > > > > Vladimir Prudnikov wrote: > > >Do you think SMiT will be interested in hunting for bugs in linux > > >drivers? These modules apparently work fine with any other hardware > > >(I'm sure professional ones do!) > > > > > >Regards, > > >Vladimir > > > > > >On Jun 12, 2008, at 5:26 PM, Frederic CAND wrote: > > > > > > > > >>Did you try to contact SMIT support ? > > >> > > >>Vladimir Prudnikov a écrit : > > >> > > >>>Didn't try Aston CAMs with mpeg4. But they do up to 12 channels of > > >>>mpeg2 perfectly well. With no problems at all. SMiTs that are for > > >>>8 services can do only 3 to 4 for me. > > >>>I think it's some kind of a driver bug because it begins working > > >>>after reinitialisation. Doesn't get hot. I have tried to call > > >>>Aston as well but with no success yet. > > >>>Regards, > > >>>Vladimir > > >>>On Jun 12, 2008, at 2:56 PM, dan.lita@sttcr.org wrote: > > >>> > > >>>>Dear Vladimir, > > >>>> > > >>>>I read your post on linux-dvb list. We have an Aston Viaccess > > >>>>Professional 2.15 CAM . > > >>>>I read that you also use Aston CAMS. My question is whether your > > >>>>Aston Viaccess cam can descramble H264 feeds or not? > > >>>>We have tried on a PACE HDTV receiver and a Tandberg unit and it > > >>>>does not descramble the H264 video pid. (black screen) > > >>>>This does not happen with Viaccess RED cam. > > >>>> > > >>>>On older Common interface adapters from Technotrend, the one for > > >>>>TT Premium DVB-S card, there was a jumper for 3V or 5V cam > > >>>>operation. > > >>>>I assume the new CI adapter does not have such jumper. If it > > >>>>still exist maybe it will be a good idea to switch from one > > >>>>voltage to the other. > > >>>>Another solution is to test whether it works or not for Irdeto to > > >>>>use an Alphacrypt Classic CAM which, at least in theory, > > >>>>according to MASCOM, supports Irdeto. > > >>>>The third thing is to notice whether the SMIT cam gets hot in > > >>>>operation. If it gets too hot maybe a fan similar to the one for > > >>>>graphics card must be put near the Common interface adapter. > > >>>> > > >>>>BTW. Do you have any e-mail address from Aston? I have tried to > > >>>>contact them but there is no e-mail address in their website. > > >>>> > > >>>>Best regards, > > >>>>Dan Lita > > >>>> > > >>>> > > >>>>Vladimir Prudnikov wrote: > > >>>> > > >>>>>Hello! > > >>>>> > > >>>>>I'm using SMIT cams to descramble channels on TT S-1500 and TT- > > >>>>>S2-3200. After some time of normal operation SMIT cams drop out > > >>>>>and stop decrypting the stream. It needs to be removed from the > > >>>>>CI slot and reinserted to resume normal operation. Aston CAMs > > >>>>>have no such problems, but they don't support 0x652 Irdeto. > > >>>>>I'm streaming with vlc. Tried many SMITs (Viaccess and Irdeto). > > >>>>>Same problem everywhere. > > >>>>> > > >>>>>Regards, > > >>>>>Vladimir > > >>>>> > > >>>>>_______________________________________________ > > >>>>>linux-dvb mailing list > > >>>>>linux-dvb@linuxtv.org > > >>>>>http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > >>>>> > > >>>>> > > >>>>> > > >>>>> > > >>>_______________________________________________ > > >>>linux-dvb mailing list > > >>>linux-dvb@linuxtv.org > > >>>http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > >>> > > >>-- > > >>CAND Frederic > > >>Product Manager > > >>ANEVIA > > >> > > > > > > > > >_______________________________________________ > > >linux-dvb mailing list > > >linux-dvb@linuxtv.org > > >http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > > > > > > > > > > > > _______________________________________________ > > linux-dvb mailing list > > linux-dvb@linuxtv.org > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > _______________________________________________ > linux-dvb mailing list > linux-dvb@linuxtv.org > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2008-06-18 16:12 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-06-12 4:12 [linux-dvb] Smit CAM problems Vladimir Prudnikov
[not found] ` <485100C3.2090908@sttcr.org>
2008-06-12 12:51 ` Vladimir Prudnikov
2008-06-12 13:26 ` Frederic CAND
2008-06-12 16:18 ` Vladimir Prudnikov
2008-06-12 17:53 ` Dan Lita
2008-06-12 18:16 ` Wolfgang Wegner
2008-06-18 16:06 ` Wolfgang Wegner
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.