* Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
@ 2008-08-14 13:29 Manuel Schneider
2008-08-14 13:47 ` Takashi Iwai
0 siblings, 1 reply; 11+ messages in thread
From: Manuel Schneider @ 2008-08-14 13:29 UTC (permalink / raw)
To: alsa-devel
Hi,
we had a Teratec Phase 22 on our transmitter line which works great
under Linux, using the ice1724 driver from alsa.
As the original sound card broke due to electrical surge on the
transmitter line, we had to replace it. The Phase 22 is not available
anymore, so we bought a Swissonic TS22PCI which is based on the Phase 22:
http://www.thomann.de/gb/swissonic_ts22pci.htm
The PCB looks exactly the same as the Phase 22, but the driver does not
initialize the card correctly:
---
dmesg:
ice1724: No matching model found for ID 0x3b157b11
ice1724: Invalid EEPROM version 0
AC'97 0 does not respond - RESET
AC'97 0 access is not valid [0xffffffff], removing mixer.
ice1712: cannot initialize pro ac97, skipped
---
I already updated to Linux 2.6.25 and tried the current alsa-drivers
package (1.0.17), but I get always the same errors in the kernel log.
I also deleted /etc/asound.* and /var/lib/alsa/asound.state, ran
alsa-conf - no luck.
Do you have any ideas how I can get this card to work?
Thanks a lot for your suggestions, more information see attached.
Manuel
---
-:[~]#> lspci -vv
00:0a.0 Multimedia audio controller: VIA Technologies
Inc. VT1720/24 [Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01)
Subsystem: TERRATEC Electronic GmbH Unknown device 117b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at c000 [size=32]
Region 1: I/O ports at bc00 [size=128]
Capabilities: [80] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
---
-:[~]#> cat /etc/modules.d/alsa
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF version 1.0.16 ---
alias snd-card-0 snd-ice1724
alias sound-slot-0 snd-ice1724
# --- END: Generated by ALSACONF, do not edit. ---
---
-:[~]#> lsmod
Module Size Used by
snd_pcm_oss 24224 0
snd_mixer_oss 14720 1 snd_pcm_oss
snd_ice1724 92328 0
snd_ice17xx_ak4xxx 3648 1 snd_ice1724
snd_ac97_codec 105704 1 snd_ice1724
snd_ak4114 8448 1 snd_ice1724
snd_pcm 59660 4
snd_pcm_oss,snd_ice1724,snd_ac97_codec,snd_ak4114
snd_timer 19272 1 snd_pcm
snd_page_alloc 8272 1 snd_pcm
snd_pt2258 4032 1 snd_ice1724
snd_i2c 5312 2 snd_ice1724,snd_pt2258
snd_ak4xxx_adda 8512 2 snd_ice1724,snd_ice17xx_ak4xxx
snd_mpu401_uart 6912 1 snd_ice1724
snd_rawmidi 19808 1 snd_mpu401_uart
snd 49288 12
snd_pcm_oss,snd_mixer_oss,snd_ice1724,snd_ac97_codec,snd_ak4114,snd_pcm,snd_timer,snd_pt2258,snd_i2c,snd_ak4xxx_adda,snd_mpu401_uart,snd_rawmidi
capi 14272 0
capifs 5072 2 capi
kernelcapi 31936 1 capi
nfs 118264 3
lockd 62064 2 nfs
sunrpc 167432 17 nfs,lockd
rtc 11384 0
via_rhine 19976 0
mii 4928 1 via_rhine
ac97_bus 1984 1 snd_ac97_codec
soundcore 6624 1 snd
---
-:[~]#> modinfo snd_ice1724
filename:
/lib/modules/2.6.25-gentoo-r7/kernel/sound/pci/ice1712/snd-ice1724.ko
license: GPL
description: VIA ICEnsemble ICE1724/1720 (Envy24HT/PT)
author: Jaroslav Kysela <perex@perex.cz>
alias: pci:v00001412d00001724sv*sd*bc*sc*i*
depends:
snd,snd-ac97-codec,snd-pcm,snd-i2c,snd-mpu401-uart,snd-ice17xx-ak4xxx,snd-pt2258,snd-ak4xxx-adda,snd-ak4114
vermagic: 2.6.25-gentoo-r7 mod_unload
parm: index:Index value for ICE1724 soundcard. (array of int)
parm: id:ID string for ICE1724 soundcard. (array of charp)
parm: enable:Enable ICE1724 soundcard. (array of bool)
parm: model:Use the given board model. (array of charp)
---
-:[~]#> cat /proc/asound/cards
0 [ICE1724 ]: ICE1724 - ICEnsemble ICE1724
ICEnsemble ICE1724 at 0xc000, irq 18
---
-:[~]#> cat /proc/asound/ICE1724/ice1724
ICEnsemble ICE1724 at 0xc000, irq 18
EEPROM:
Subvendor : 0x3b157b11
Size : 32 bytes
Version : 0
System Config : 0x0
ACLink : 0x0
I2S : 0x0
S/PDIF : 0x0
GPIO direction : 0xffff00
GPIO mask : 0xffffff
GPIO state : 0xffffff
Extra #18 : 0xff
Extra #19 : 0xff
Extra #20 : 0xff
Extra #21 : 0xff
Extra #22 : 0xff
Extra #23 : 0xff
Extra #24 : 0xff
Extra #25 : 0xff
Extra #26 : 0x0
Extra #27 : 0x0
Extra #28 : 0x0
Extra #29 : 0x0
Extra #30 : 0x0
Extra #31 : 0x0
...
---
--
Kanal Ratte 104,5 MHz
...das Freie Radio im Wiesental
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-14 13:29 Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724 Manuel Schneider
@ 2008-08-14 13:47 ` Takashi Iwai
2008-08-14 14:03 ` Manuel Schneider
[not found] ` <48A43A2A.7050701@kanal-ratte.de>
0 siblings, 2 replies; 11+ messages in thread
From: Takashi Iwai @ 2008-08-14 13:47 UTC (permalink / raw)
To: Manuel Schneider; +Cc: alsa-devel
At Thu, 14 Aug 2008 15:29:18 +0200,
Manuel Schneider wrote:
>
> Hi,
>
> we had a Teratec Phase 22 on our transmitter line which works great
> under Linux, using the ice1724 driver from alsa.
> As the original sound card broke due to electrical surge on the
> transmitter line, we had to replace it. The Phase 22 is not available
> anymore, so we bought a Swissonic TS22PCI which is based on the Phase 22:
> http://www.thomann.de/gb/swissonic_ts22pci.htm
>
> The PCB looks exactly the same as the Phase 22, but the driver does not
> initialize the card correctly:
>
> ---
> dmesg:
> ice1724: No matching model found for ID 0x3b157b11
> ice1724: Invalid EEPROM version 0
> AC'97 0 does not respond - RESET
> AC'97 0 access is not valid [0xffffffff], removing mixer.
> ice1712: cannot initialize pro ac97, skipped
> ---
>
> I already updated to Linux 2.6.25 and tried the current alsa-drivers
> package (1.0.17), but I get always the same errors in the kernel log.
> I also deleted /etc/asound.* and /var/lib/alsa/asound.state, ran
> alsa-conf - no luck.
>
> Do you have any ideas how I can get this card to work?
Pass model=phase22 module option to snd-ice1724 driver. Then it
handles the card as if it's phase22.
Takashi
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-14 13:47 ` Takashi Iwai
@ 2008-08-14 14:03 ` Manuel Schneider
[not found] ` <48A43A2A.7050701@kanal-ratte.de>
1 sibling, 0 replies; 11+ messages in thread
From: Manuel Schneider @ 2008-08-14 14:03 UTC (permalink / raw)
To: alsa-devel
Takashi Iwai schrieb, Am 14.08.2008 15:47:
> Pass model=phase22 module option to snd-ice1724 driver. Then it
> handles the card as if it's phase22.
Thanks for this hin. Unfortunately it changes nothing - still kernel
error message, still no usable sound device.
I also tried the following kernel patch, which gives me an accessible
sound device and usable mixer (and no kernel error), but recording does
not work (just noise).
The patch is quite simple - it just adds the subvendor ID of the
Swissonic card and adds all phase22 functionality to it.
Manuel
---
-:[/usr/src/linux/sound/pci/ice1712]#> diff -uN phase.h.bak phase.h
--- phase.h.bak 2008-08-12 10:13:49.000000000 +0200
+++ phase.h 2008-08-12 09:49:23.000000000 +0200
@@ -25,9 +25,11 @@
*/
#define PHASE_DEVICE_DESC "{Terratec,Phase 22},"\
+ "{Swissonic,TS22PCI},"\
"{Terratec,Phase 28},"
#define VT1724_SUBDEVICE_PHASE22 0x3b155011
+#define VT1724_SUBDEVICE_TS22PCI 0x3b157b11
#define VT1724_SUBDEVICE_PHASE28 0x3b154911
/* entry point */
---
---
-:[/usr/src/linux/sound/pci/ice1712]#> diff -uN phase.c.bak phase.c
--- phase.c.bak 2008-08-12 09:51:28.000000000 +0200
+++ phase.c 2008-08-12 09:51:28.000000000 +0200
@@ -124,6 +124,11 @@
ice->num_total_adcs = 2;
ice->vt1720 = 1; // Envy24HT-S have 16 bit wide GPIO
break;
+ case VT1724_SUBDEVICE_TS22PCI:
+ ice->num_total_dacs = 2;
+ ice->num_total_adcs = 2;
+ ice->vt1720 = 1; // Envy24HT-S have 16 bit wide GPIO
+ break;
default:
snd_BUG();
return -EINVAL;
@@ -139,6 +144,10 @@
if ((err = snd_ice1712_akm4xxx_init(ak, &akm_phase22,
&akm_phase22_priv, ice)) < 0)
return err;
break;
+ case VT1724_SUBDEVICE_TS22PCI:
+ if ((err = snd_ice1712_akm4xxx_init(ak, &akm_phase22,
&akm_phase22_priv, ice)) < 0)
+ return err;
+ break;
}
return 0;
@@ -153,6 +162,10 @@
err = snd_ice1712_akm4xxx_build_controls(ice);
if (err < 0)
return err;
+ case VT1724_SUBDEVICE_TS22PCI:
+ err = snd_ice1712_akm4xxx_build_controls(ice);
+ if (err < 0)
+ return err;
}
return 0;
}
@@ -896,6 +909,15 @@
.eeprom_data = phase22_eeprom,
},
{
+ .subvendor = VT1724_SUBDEVICE_TS22PCI,
+ .name = "Swissonic TS22PCI",
+ .model = "phase22",
+ .chip_init = phase22_init,
+ .build_controls = phase22_add_controls,
+ .eeprom_size = sizeof(phase22_eeprom),
+ .eeprom_data = phase22_eeprom,
+ },
+ {
.subvendor = VT1724_SUBDEVICE_PHASE28,
.name = "Terratec PHASE 28",
.model = "phase28",
---
--
Kanal Ratte 104,5 MHz
...das Freie Radio im Wiesental
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
[not found] ` <48A43A2A.7050701@kanal-ratte.de>
@ 2008-08-14 14:03 ` Takashi Iwai
2008-08-14 14:09 ` Manuel Schneider
[not found] ` <48A43C11.10904@kanal-ratte.de>
0 siblings, 2 replies; 11+ messages in thread
From: Takashi Iwai @ 2008-08-14 14:03 UTC (permalink / raw)
To: Manuel Schneider; +Cc: alsa-devel
At Thu, 14 Aug 2008 15:59:06 +0200,
Manuel Schneider wrote:
>
> Takashi Iwai schrieb, Am 14.08.2008 15:47:
>
> > Pass model=phase22 module option to snd-ice1724 driver. Then it
> > handles the card as if it's phase22.
>
> Thanks for this hin. Unfortunately it changes nothing - still kernel
> error message, still no usable sound device.
Are you sure? With the proper model name, at least you won't get
EEPROM version error any more.
>
> I also tried the following kernel patch, which gives me an accessible
> sound device and usable mixer (and no kernel error), but recording does
> not work (just noise).
Likely an incompatible hardware design for the recording...
Takashi
> The patch is quite simple - it just adds the subvendor ID of the
> Swissonic card and adds all phase22 functionality to it.
>
> Manuel
>
> ---
> -:[/usr/src/linux/sound/pci/ice1712]#> diff -uN phase.h.bak phase.h
> --- phase.h.bak 2008-08-12 10:13:49.000000000 +0200
> +++ phase.h 2008-08-12 09:49:23.000000000 +0200
> @@ -25,9 +25,11 @@
> */
>
> #define PHASE_DEVICE_DESC "{Terratec,Phase 22},"\
> + "{Swissonic,TS22PCI},"\
> "{Terratec,Phase 28},"
>
> #define VT1724_SUBDEVICE_PHASE22 0x3b155011
> +#define VT1724_SUBDEVICE_TS22PCI 0x3b157b11
> #define VT1724_SUBDEVICE_PHASE28 0x3b154911
>
> /* entry point */
> ---
>
> ---
> -:[/usr/src/linux/sound/pci/ice1712]#> diff -uN phase.c.bak phase.c
> --- phase.c.bak 2008-08-12 09:51:28.000000000 +0200
> +++ phase.c 2008-08-12 09:51:28.000000000 +0200
> @@ -124,6 +124,11 @@
> ice->num_total_adcs = 2;
> ice->vt1720 = 1; // Envy24HT-S have 16 bit wide GPIO
> break;
> + case VT1724_SUBDEVICE_TS22PCI:
> + ice->num_total_dacs = 2;
> + ice->num_total_adcs = 2;
> + ice->vt1720 = 1; // Envy24HT-S have 16 bit wide GPIO
> + break;
> default:
> snd_BUG();
> return -EINVAL;
> @@ -139,6 +144,10 @@
> if ((err = snd_ice1712_akm4xxx_init(ak, &akm_phase22,
> &akm_phase22_priv, ice)) < 0)
> return err;
> break;
> + case VT1724_SUBDEVICE_TS22PCI:
> + if ((err = snd_ice1712_akm4xxx_init(ak, &akm_phase22,
> &akm_phase22_priv, ice)) < 0)
> + return err;
> + break;
> }
>
> return 0;
> @@ -153,6 +162,10 @@
> err = snd_ice1712_akm4xxx_build_controls(ice);
> if (err < 0)
> return err;
> + case VT1724_SUBDEVICE_TS22PCI:
> + err = snd_ice1712_akm4xxx_build_controls(ice);
> + if (err < 0)
> + return err;
> }
> return 0;
> }
> @@ -896,6 +909,15 @@
> .eeprom_data = phase22_eeprom,
> },
> {
> + .subvendor = VT1724_SUBDEVICE_TS22PCI,
> + .name = "Swissonic TS22PCI",
> + .model = "phase22",
> + .chip_init = phase22_init,
> + .build_controls = phase22_add_controls,
> + .eeprom_size = sizeof(phase22_eeprom),
> + .eeprom_data = phase22_eeprom,
> + },
> + {
> .subvendor = VT1724_SUBDEVICE_PHASE28,
> .name = "Terratec PHASE 28",
> .model = "phase28",
> ---
>
>
>
> --
> Kanal Ratte 104,5 MHz
> ...das Freie Radio im Wiesental
>
> Hauptstrasse 82
> 79650 Schopfheim
>
> Tel: +49 7622 6692-53
> Fax: +49 7622 6692-54
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-14 14:03 ` Takashi Iwai
@ 2008-08-14 14:09 ` Manuel Schneider
[not found] ` <48A43C11.10904@kanal-ratte.de>
1 sibling, 0 replies; 11+ messages in thread
From: Manuel Schneider @ 2008-08-14 14:09 UTC (permalink / raw)
To: alsa-devel
Takashi Iwai schrieb, Am 14.08.2008 16:03:
> At Thu, 14 Aug 2008 15:59:06 +0200,
> Manuel Schneider wrote:
>> Takashi Iwai schrieb, Am 14.08.2008 15:47:
>>
>>> Pass model=phase22 module option to snd-ice1724 driver. Then it
>>> handles the card as if it's phase22.
>> Thanks for this hin. Unfortunately it changes nothing - still kernel
>> error message, still no usable sound device.
>
> Are you sure? With the proper model name, at least you won't get
> EEPROM version error any more.
yes, pretty sure. I just reverted my patch and recompiled the driver to
check it out:
ice1712: cannot initialize pro ac97, skipped
ice1724: No matching model found for ID 0x3b157b11
ice1724: Invalid EEPROM version 0
AC'97 0 does not respond - RESET
AC'97 0 access is not valid [0xffffffff], removing mixer.
ice1712: cannot initialize pro ac97, skipped
>> I also tried the following kernel patch, which gives me an accessible
>> sound device and usable mixer (and no kernel error), but recording does
>> not work (just noise).
>
> Likely an incompatible hardware design for the recording...
I guess it's another firmware... I can't test playback as I only have
remote access to the server and it is only used for recording
(streaming) but I assume it does also not work.
I admit that this patch was just a hack to try it out.
Manuel
--
Kanal Ratte 104,5 MHz
...das Freie Radio im Wiesental
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
[not found] ` <48A43C11.10904@kanal-ratte.de>
@ 2008-08-14 14:13 ` Takashi Iwai
2008-08-14 16:05 ` Manuel Schneider
2008-08-20 6:51 ` Manuel Schneider
0 siblings, 2 replies; 11+ messages in thread
From: Takashi Iwai @ 2008-08-14 14:13 UTC (permalink / raw)
To: Manuel Schneider; +Cc: alsa-devel
At Thu, 14 Aug 2008 16:07:13 +0200,
Manuel Schneider wrote:
>
> Takashi Iwai schrieb, Am 14.08.2008 16:03:
>
> > At Thu, 14 Aug 2008 15:59:06 +0200,
> > Manuel Schneider wrote:
> >> Takashi Iwai schrieb, Am 14.08.2008 15:47:
> >>
> >>> Pass model=phase22 module option to snd-ice1724 driver. Then it
> >>> handles the card as if it's phase22.
> >> Thanks for this hin. Unfortunately it changes nothing - still kernel
> >> error message, still no usable sound device.
> >
> > Are you sure? With the proper model name, at least you won't get
> > EEPROM version error any more.
>
>
> yes, pretty sure. I just reverted my patch and recompiled the driver to
> check it out:
>
> ice1712: cannot initialize pro ac97, skipped
> ice1724: No matching model found for ID 0x3b157b11
This means that you didn't pass the model option properly.
> ice1724: Invalid EEPROM version 0
> AC'97 0 does not respond - RESET
> AC'97 0 access is not valid [0xffffffff], removing mixer.
> ice1712: cannot initialize pro ac97, skipped
>
>
> >> I also tried the following kernel patch, which gives me an accessible
> >> sound device and usable mixer (and no kernel error), but recording does
> >> not work (just noise).
> >
> > Likely an incompatible hardware design for the recording...
>
> I guess it's another firmware...
The board has no firmware to load.
> I can't test playback as I only have
> remote access to the server and it is only used for recording
> (streaming) but I assume it does also not work.
> I admit that this patch was just a hack to try it out.
First you should check whether the exactly same codec chip, AK4524, on
it.
Takashi
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-14 14:13 ` Takashi Iwai
@ 2008-08-14 16:05 ` Manuel Schneider
2008-08-20 6:51 ` Manuel Schneider
1 sibling, 0 replies; 11+ messages in thread
From: Manuel Schneider @ 2008-08-14 16:05 UTC (permalink / raw)
To: alsa-devel
Am Donnerstag, 14. August 2008 schrieb Takashi Iwai:
> > I guess it's another firmware...
>
> The board has no firmware to load.
well, I was thinking of the eeprom.
> First you should check whether the exactly same codec chip, AK4524, on
> it.
Yes, it has, but another model no (or whatever it is). I just have both
cards - the original Phase 22 and the new TS22 here:
Phase 22:
AKM AK4524VF 193A0547N
VIA ENVY24HT-S VT1721-0522CD 2IA0000551
TS22:
AKM AK4524VF 247A0805N
VIA ENVY24HT-S VT1721-0810CD 2IA0001861
The PCBs are nearly the same, but the TS22 lacks the following parts:
X3 quartz
UD09 and UD10 (both ICs)
On the Back of the Swissonic TS22 it says "Terrasoniq" - which is knows as yet
another vendor of sound cards. Swissonic seems to be just another brand of
the same product.
Something about the noise / recording:
When I unpug the lines, the noise still persists.
When I fade down both ADC lines with alsamixer, the noise perists until I
reach 0. Then it is mute.
When I fade up ADC1 I can hear some of the to-be-recorded signal very
distorted behind the noise.
Greets,
Manuel
--
Kanal Ratte 104,5 MHz
...das Freie Radio im Wiesental
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-14 14:13 ` Takashi Iwai
2008-08-14 16:05 ` Manuel Schneider
@ 2008-08-20 6:51 ` Manuel Schneider
2008-08-21 9:14 ` Takashi Iwai
1 sibling, 1 reply; 11+ messages in thread
From: Manuel Schneider @ 2008-08-20 6:51 UTC (permalink / raw)
To: Takashi Iwai; +Cc: alsa-devel
Ok, now to come back to my problems with the Swissonic / Terrasoniq TS22
card.
Yesterday I checked the other cards I got in another Linux system, using
the same base system, but on x86. In these systems the cards work
perfectly, using "model=phase22". The server we've been talking about
before is an amd64 system.
Suspecting a hardware problem with this individual card I replaced it,
but the problem persists with other cards which worked fine in the x86
systems. I also copied over /etc/modules.d/alsa, /etc/asound.conf and
/var/lib/alsa/asound.state from the other system - just to be sure.
But it doesn't help - I still just get a terrible noise.
You might want to check it on http://radio.kanal-ratte.de:8000/rkr.ogg.
So there has to be a kind of a bug on amd64 systems...
Any ideas? The original Phase22 worked fine before the incident...
Greets,
Manuel
--
Kanal Ratte 104,5 MHz
...das Freie Radio im Wiesental
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-20 6:51 ` Manuel Schneider
@ 2008-08-21 9:14 ` Takashi Iwai
2008-08-21 9:34 ` Manuel Schneider
2008-08-27 17:15 ` Manuel Schneider
0 siblings, 2 replies; 11+ messages in thread
From: Takashi Iwai @ 2008-08-21 9:14 UTC (permalink / raw)
To: Manuel Schneider; +Cc: alsa-devel
At Wed, 20 Aug 2008 08:51:39 +0200,
Manuel Schneider wrote:
>
> Ok, now to come back to my problems with the Swissonic / Terrasoniq TS22
> card.
>
> Yesterday I checked the other cards I got in another Linux system, using
> the same base system, but on x86. In these systems the cards work
> perfectly, using "model=phase22". The server we've been talking about
> before is an amd64 system.
OK, then I can add TS22PCI entry as phase22 compatible.
> Suspecting a hardware problem with this individual card I replaced it,
> but the problem persists with other cards which worked fine in the x86
> systems. I also copied over /etc/modules.d/alsa, /etc/asound.conf and
> /var/lib/alsa/asound.state from the other system - just to be sure.
How is the problem? Still only the recording doesn't work while
playback is OK as you described before?
And which "other cards"? Another TS88PCI?
thanks,
Takashi
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-21 9:14 ` Takashi Iwai
@ 2008-08-21 9:34 ` Manuel Schneider
2008-08-27 17:15 ` Manuel Schneider
1 sibling, 0 replies; 11+ messages in thread
From: Manuel Schneider @ 2008-08-21 9:34 UTC (permalink / raw)
To: alsa-devel
Takashi Iwai schrieb, Am 21.08.2008 11:14:
>
> OK, then I can add TS22PCI entry as phase22 compatible.
yes, you can do that. On x86 both recording and playback is just fine.
>> Suspecting a hardware problem with this individual card I replaced it,
>> but the problem persists with other cards which worked fine in the x86
>> systems. I also copied over /etc/modules.d/alsa, /etc/asound.conf and
>> /var/lib/alsa/asound.state from the other system - just to be sure.
>
> How is the problem? Still only the recording doesn't work while
> playback is OK as you described before?
>
> And which "other cards"? Another TS88PCI?
Another TS22PCI. I've got three of them - one to replace the broken
Phase 22 in the server (which doesn't work) and two others for x86
systems which work fine.
To exclude a hardware problem with this specific card I've put into the
server I replaced the three cards but the server still has the same problem.
Unfurtunatly it is a problem for me to check playback due to missing
equipment at the server rack to plug into the sound card to check it. I
will look for a solution. The server is at a remote place so I mostly
have only ssh access to it.
Is there any other information I can provide for you to help finding the
problem?
Greets,
Manuel
--
Kanal Ratte 104,5 MHz
...das Freie Radio im Wiesental
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724
2008-08-21 9:14 ` Takashi Iwai
2008-08-21 9:34 ` Manuel Schneider
@ 2008-08-27 17:15 ` Manuel Schneider
1 sibling, 0 replies; 11+ messages in thread
From: Manuel Schneider @ 2008-08-27 17:15 UTC (permalink / raw)
To: alsa-devel; +Cc: Takashi Iwai
Good news:
It works now.
But I still suspect a bug / an incompatibilty in the driver.
Today, I checked playback - that worked perfectly. Then I tried arecord /
aplay - perfectly.
Then I switched the encoder (darkice) from OSS to alsa - now that works to. I
rechecked OSS - it's definitely the OSS compatibility layer which does not
work - but worked fine before the card was replaced.
I also found another problem but this might be a darkice bug but I still want
to discuss it, because I had this problem with other cards, too:
When using alsa in darkice, setting the samplerate to 44100 in darkice as well
as the mixer the samplerates still do not match. The 44100 Hz stream is "too
fast", resulting in mickey mouse voices and lag every few seconds.
This issue can be solved by setting defaults.pcm.dmix.rate to 44100 in
/usr/share/alsa/alsa.conf.
Do you have an idea why this problem is here? Is it truely a darkice bug, as
it doesn't set the samplerate of the sounddevice properly or where is the
cause?
Greets and thanks für the help,
Manuel
--
Kanal Ratte 104,5 MHz
Freies Radio Schopfheim
Hauptstrasse 82
79650 Schopfheim
Tel: +49 7622 6692-53
Fax: +49 7622 6692-54
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2008-08-27 17:15 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-08-14 13:29 Swissonic TS22PCI / Teratec Phase 22 / driver problems with ice1724 Manuel Schneider
2008-08-14 13:47 ` Takashi Iwai
2008-08-14 14:03 ` Manuel Schneider
[not found] ` <48A43A2A.7050701@kanal-ratte.de>
2008-08-14 14:03 ` Takashi Iwai
2008-08-14 14:09 ` Manuel Schneider
[not found] ` <48A43C11.10904@kanal-ratte.de>
2008-08-14 14:13 ` Takashi Iwai
2008-08-14 16:05 ` Manuel Schneider
2008-08-20 6:51 ` Manuel Schneider
2008-08-21 9:14 ` Takashi Iwai
2008-08-21 9:34 ` Manuel Schneider
2008-08-27 17:15 ` Manuel Schneider
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.