* [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31
@ 2008-09-18 14:58 Jean-Christophe PLAGNIOL-VILLARD
2008-09-18 14:58 ` [U-Boot] [PATCH] update uImgae FIT multi documentation Jean-Christophe PLAGNIOL-VILLARD
2008-09-29 13:38 ` [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Shinya Kuribayashi
0 siblings, 2 replies; 3+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-09-18 14:58 UTC (permalink / raw)
To: u-boot
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/README.imx31 b/README.imx31
deleted file mode 100644
index f545f01..0000000
--- a/README.imx31
+++ /dev/null
@@ -1,13 +0,0 @@
-i.MX31 specific Configuration Options:
---------------------------------------
-
-- Timer precision:
- CONFIG_MX31_TIMER_HIGH_PRECISION
-
- Enable higher precision timer. The low-precision timer
- (default) provides approximately 4% error, whereas the
- high-precision timer is about 0.4% accurate. The extra
- accuracy is achieved at the cost of higher computational
- overhead, which, in places where time is measured, should
- not be critical, so, it should be safe to enable this
- option.
diff --git a/doc/README.imx31 b/doc/README.imx31
new file mode 100644
index 0000000..91ef766
--- /dev/null
+++ b/doc/README.imx31
@@ -0,0 +1,29 @@
+U-Boot for Freescale i.MX31
+
+This file contains information for the port of U-Boot to the Freescale
+i.MX31 SoC.
+
+1. CONFIGURATION OPTIONS/SETTINGS
+---------------------------------
+
+1.1 Configuration of MC13783 SPI bus
+------------------------------------
+ The power management companion chip MC13783 is connected to the
+ i.MX31 via an SPI bus. Use the following configuration options
+ to setup the bus and chip select used for a particular board.
+
+ CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
+ Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
+ CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
+
+1.2 Timer precision
+-------------------
+ CONFIG_MX31_TIMER_HIGH_PRECISION
+
+ Enable higher precision timer. The low-precision timer
+ (default) provides approximately 4% error, whereas the
+ high-precision timer is about 0.4% accurate. The extra
+ accuracy is achieved at the cost of higher computational
+ overhead, which, in places where time is measured, should
+ not be critical, so, it should be safe to enable this
+ option.
diff --git a/doc/README.mx31 b/doc/README.mx31
deleted file mode 100644
index 291c2f3..0000000
--- a/doc/README.mx31
+++ /dev/null
@@ -1,17 +0,0 @@
-U-Boot for Freescale i.MX31
-
-This file contains information for the port of U-Boot to the Freescale
-i.MX31 SoC.
-
-1. CONFIGURATION OPTIONS/SETTINGS
----------------------------------
-
-1.1 Configuration of MC13783 SPI bus
-------------------------------------
-The power management companion chip MC13783 is connected to the
-i.MX31 via an SPI bus. Use the following configuration options
-to setup the bus and chip select used for a particular board.
-
-CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
- Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
-CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
--
1.5.6.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH] update uImgae FIT multi documentation
2008-09-18 14:58 [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Jean-Christophe PLAGNIOL-VILLARD
@ 2008-09-18 14:58 ` Jean-Christophe PLAGNIOL-VILLARD
2008-09-29 13:38 ` [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Shinya Kuribayashi
1 sibling, 0 replies; 3+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-09-18 14:58 UTC (permalink / raw)
To: u-boot
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/doc/uImage.FIT/multi.its b/doc/uImage.FIT/multi.its
index b992962..1d8c2db 100644
--- a/doc/uImage.FIT/multi.its
+++ b/doc/uImage.FIT/multi.its
@@ -56,6 +56,7 @@
data = /incbin/("./eldk-4.2-ramdisk");
type = "ramdisk";
arch = "ppc";
+ os = "linux";
compression = "gzip";
hash at 1 {
algo = "sha1";
@@ -67,6 +68,7 @@
data = /incbin/("./eldk-3.1-ramdisk");
type = "ramdisk";
arch = "ppc";
+ os = "linux";
compression = "gzip";
hash at 1 {
algo = "crc32";
--
1.5.6.5
^ permalink raw reply related [flat|nested] 3+ messages in thread* [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31
2008-09-18 14:58 [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Jean-Christophe PLAGNIOL-VILLARD
2008-09-18 14:58 ` [U-Boot] [PATCH] update uImgae FIT multi documentation Jean-Christophe PLAGNIOL-VILLARD
@ 2008-09-29 13:38 ` Shinya Kuribayashi
1 sibling, 0 replies; 3+ messages in thread
From: Shinya Kuribayashi @ 2008-09-29 13:38 UTC (permalink / raw)
To: u-boot
Ping. Please consider making this into the upcoming release.
Jean-Christophe PLAGNIOL-VILLARD wrote:
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>
> diff --git a/README.imx31 b/README.imx31
> deleted file mode 100644
> index f545f01..0000000
> --- a/README.imx31
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -i.MX31 specific Configuration Options:
> ---------------------------------------
> -
> -- Timer precision:
> - CONFIG_MX31_TIMER_HIGH_PRECISION
> -
> - Enable higher precision timer. The low-precision timer
> - (default) provides approximately 4% error, whereas the
> - high-precision timer is about 0.4% accurate. The extra
> - accuracy is achieved at the cost of higher computational
> - overhead, which, in places where time is measured, should
> - not be critical, so, it should be safe to enable this
> - option.
> diff --git a/doc/README.imx31 b/doc/README.imx31
> new file mode 100644
> index 0000000..91ef766
> --- /dev/null
> +++ b/doc/README.imx31
> @@ -0,0 +1,29 @@
> +U-Boot for Freescale i.MX31
> +
> +This file contains information for the port of U-Boot to the Freescale
> +i.MX31 SoC.
> +
> +1. CONFIGURATION OPTIONS/SETTINGS
> +---------------------------------
> +
> +1.1 Configuration of MC13783 SPI bus
> +------------------------------------
> + The power management companion chip MC13783 is connected to the
> + i.MX31 via an SPI bus. Use the following configuration options
> + to setup the bus and chip select used for a particular board.
> +
> + CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
> + Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
> + CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
> +
> +1.2 Timer precision
> +-------------------
> + CONFIG_MX31_TIMER_HIGH_PRECISION
> +
> + Enable higher precision timer. The low-precision timer
> + (default) provides approximately 4% error, whereas the
> + high-precision timer is about 0.4% accurate. The extra
> + accuracy is achieved at the cost of higher computational
> + overhead, which, in places where time is measured, should
> + not be critical, so, it should be safe to enable this
> + option.
> diff --git a/doc/README.mx31 b/doc/README.mx31
> deleted file mode 100644
> index 291c2f3..0000000
> --- a/doc/README.mx31
> +++ /dev/null
> @@ -1,17 +0,0 @@
> -U-Boot for Freescale i.MX31
> -
> -This file contains information for the port of U-Boot to the Freescale
> -i.MX31 SoC.
> -
> -1. CONFIGURATION OPTIONS/SETTINGS
> ----------------------------------
> -
> -1.1 Configuration of MC13783 SPI bus
> -------------------------------------
> -The power management companion chip MC13783 is connected to the
> -i.MX31 via an SPI bus. Use the following configuration options
> -to setup the bus and chip select used for a particular board.
> -
> -CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
> - Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
> -CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2008-09-29 13:38 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-18 14:58 [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Jean-Christophe PLAGNIOL-VILLARD
2008-09-18 14:58 ` [U-Boot] [PATCH] update uImgae FIT multi documentation Jean-Christophe PLAGNIOL-VILLARD
2008-09-29 13:38 ` [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Shinya Kuribayashi
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.