* 2.6.26.6: ata4.00: exception Emask 0x0 SAct 0x8 SErr 0x1800000 action 0x6 frozen
@ 2008-10-15 18:15 Jan De Luyck
0 siblings, 0 replies; only message in thread
From: Jan De Luyck @ 2008-10-15 18:15 UTC (permalink / raw)
To: LKML
Hey folks,
When booting my system today the following nice chunk came up in the dmesg:
XFS mounting filesystem sdd1
ata4: EH in SWNCQ mode,QC:qc_active 0x8 sactive 0x8
ata4: SWNCQ:qc_active 0x8 defer_bits 0x0 last_issue_tag 0x3
dhfis 0x8 dmafis 0x8 sdbfis 0x0
ata4: ATA_REG 0x40 ERR_REG 0x0
ata4: tag : dhfis dmafis sdbfis sacitve
ata4: tag 0x3: 1 1 0 1
ata4.00: exception Emask 0x0 SAct 0x8 SErr 0x1800000 action 0x6 frozen
ata4: SError: { LinkSeq TrStaTrns }
ata4.00: cmd 60/00:18:d3:d1:a2/04:00:12:00:00/40 tag 3 ncq 524288 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x3)
ata4.00: revalidation failed (errno=-5)
ata4: failed to recover some devices, retrying in 5 secs
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x3)
ata4.00: revalidation failed (errno=-5)
ata4: failed to recover some devices, retrying in 5 secs
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x3)
ata4.00: revalidation failed (errno=-5)
ata4.00: disabled
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4: EH complete
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 312660435
I/O error in filesystem ("sdd1") meta-data dev sdd1 block 0x12a2c594 ("xlog_bread") error 5 buf count 2097152
XFS: empty log check failed
XFS: log mount/recovery failed: error 5
XFS: log mount failed
end_request: I/O error, dev sdd, sector 0
followed later by:
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
Buffer I/O error on device sdd, logical block 1
Buffer I/O error on device sdd, logical block 2
Buffer I/O error on device sdd, logical block 3
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 63
Buffer I/O error on device sdd1, logical block 0
Buffer I/O error on device sdd1, logical block 1
Buffer I/O error on device sdd1, logical block 2
Buffer I/O error on device sdd1, logical block 3
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 63
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 65
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 67
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 69
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 0
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 8
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 16
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 24
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 0
sd 3:0:0:0: [sdd] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sdd, sector 0
Is my disk dying? Or is just a SWNCQ bug in the disk firmware?
sdd is not accessible at this time.
Motherboard is an Asus M2N-SLI Deluxe.
Disks:
sata_nv 0000:00:05.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:05.0: Using SWNCQ mode
PCI: Setting latency timer of device 0000:00:05.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 23
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 23
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3160812AS, 3.AAH, max UDMA/133
ata1.00: 312581808 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3160812AS, 3.AAH, max UDMA/133
ata2.00: 312581808 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
isa bounce pool size: 16 pages
scsi 0:0:0:0: Direct-Access ATA ST3160812AS 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: Direct-Access ATA ST3160812AS 3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 1:0:0:0: [sdb] Attached SCSI disk
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:05.1: Using SWNCQ mode
PCI: Setting latency timer of device 0000:00:05.1 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 22
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 22
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: native sectors (586072368) is smaller than sectors (625142448)
ata3.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
ata3.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: native sectors (586072368) is smaller than sectors (625142448)
ata4.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
ata4.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 >
sd 2:0:0:0: [sdc] Attached SCSI disk
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 3:0:0:0: [sdd] Attached SCSI disk
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:05.2: Using SWNCQ mode
PCI: Setting latency timer of device 0000:00:05.2 to 64
scsi4 : sata_nv
scsi5 : sata_nv
ata5: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb400 irq 21
ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb800 bmdma 0xb408 irq 21
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata5.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
ata6: SATA link down (SStatus 0 SControl 300)
scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1 sde2 sde3 sde4 < sde5 >
sd 4:0:0:0: [sde] Attached SCSI disk
pata_amd 0000:00:04.0: version 0.3.10
PCI: Setting latency timer of device 0000:00:04.0 to 64
scsi6 : pata_amd
scsi7 : pata_amd
ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata7.00: ATAPI: _NEC DVD_RW ND-2500A, 1.08, max UDMA/33
ata7.01: ATAPI: BENQ DVD LS DW1655, BCIB, max UDMA/33
ata7: nv_mode_filter: 0x739f&0x707f->0x701f, BIOS=0x7000 (0xc0c00000) ACPI=0x0
ata7: nv_mode_filter: 0x739f&0x707f->0x701f, BIOS=0x7000 (0xc0c00000) ACPI=0x0
ata7.00: configured for UDMA/33
ata7.01: configured for UDMA/33
ata8: port disabled. ignoring.
scsi 6:0:0:0: CD-ROM _NEC DVD_RW ND-2500A 1.08 PQ: 0 ANSI: 5
scsi 6:0:1:0: CD-ROM BENQ DVD LS DW1655 BCIB PQ: 0 ANSI: 5
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2008-10-15 18:45 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-10-15 18:15 2.6.26.6: ata4.00: exception Emask 0x0 SAct 0x8 SErr 0x1800000 action 0x6 frozen Jan De Luyck
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.