From: Reinhard Nissl <rnissl@gmx.de>
To: linux-kernel@vger.kernel.org
Cc: Greg KH <greg@kroah.com>, akpm@linux-foundation.org, stable@kernel.org
Subject: Re: PATCH: mvsas: increase port type detection delay to suit Seagate's 15k6 drive ST3450856SS 0003
Date: Sun, 21 Dec 2008 20:11:59 +0100 [thread overview]
Message-ID: <494E94FF.3090809@gmx.de> (raw)
In-Reply-To: <20081215000412.GC5622@kroah.com>
[-- Attachment #1: Type: text/plain, Size: 2000 bytes --]
Hi,
Greg KH schrieb:
> On Sun, Dec 14, 2008 at 11:50:04PM +0100, Reinhard Nissl wrote:
>
>> Hi Greg,
>>
>> I hope you don't mind following your suggestion:
>>
>>> Also, please cc: the stable developers if you want them to pay attention
>>> to messages like this.
>
> It's easier to email stable@kernel.org to make sure that I don't miss it
> :)
>
> Is the patch below in Linus's tree? If so, do you have a git commit id?
This time, the attached patch is against Linus' tree
(linux/kernel/git/torvalds/linux-2.6.git). I'd be glad if Andrew
would commit it so that you can pull it over to stable.
Thanks in advance.
Bye.
--
Dipl.-Inform. (FH) Reinhard Nissl
mailto:rnissl@gmx.de
> If not, we need to wait until it is there before we can accept it into
> the stable tree.
>
> thanks,
>
> greg k-h
>
>> -------- Original-Nachricht --------
>> Betreff: Re: PATCH: mvsas: increase port type detection delay to
>> suit Seagate's 15k6 drive ST3450856SS 0003
>> Datum: Fri, 12 Dec 2008 21:23:45 +0100
>> Von: Reinhard Nissl <rnissl@gmx.de>
>> An: linux-scsi@vger.kernel.org
>> CC: Ke Wei <kewei@marvell.com>, Jeff Garzik
>> <jgarzik@redhat.com>, James Bottomley
>> <James.Bottomley@hansenpartnership.com>
>> Referenzen: <493BC76F.3060105@gmx.de> <49405137.9000902@gmx.de>
>>
>> Hi,
>>
>> I wonder why no one has dropped me a line so far. I hope you
>> don't mind CCing you directly. I found your email addresses on
>> mailing list entries regarding mvsas. I attach the little patch
>> again for ease of use.
>>
>> Reinhard Nissl schrieb:
>>
>>> I increased the delay step by step until loading of mvsas
>>> reliably detected the drive 200 times in sequence. A much better
>>> approach would be to monitor the hardware for some flag which
>>> indicates that port detection has finished, but I do not have any
>>> hardware documentation.
>>>
>>> BTW: patch is against
>>> git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-2.6.27.y.git
>>>
>>> Signed-off-by: Reinhard Nissl <rnissl@gmx.de>
[-- Attachment #2: mvsas.diff --]
[-- Type: text/x-patch, Size: 533 bytes --]
drivers/scsi/mvsas.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/drivers/scsi/mvsas.c b/drivers/scsi/mvsas.c
index 1dd70d7..23e5a87 100644
--- a/drivers/scsi/mvsas.c
+++ b/drivers/scsi/mvsas.c
@@ -2959,7 +2959,7 @@ static int __devinit mvs_hw_init(struct mvs_info *mvi)
/* enable auto port detection */
mw32(GBL_PORT_TYPE, MODE_AUTO_DET_EN);
- msleep(100);
+ msleep(1100);
/* init and reset phys */
for (i = 0; i < mvi->chip->n_phy; i++) {
u32 lo = be32_to_cpu(*(u32 *)&mvi->sas_addr[4]);
next prev parent reply other threads:[~2008-12-21 19:12 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-12-14 22:50 PATCH: mvsas: increase port type detection delay to suit Seagate's 15k6 drive ST3450856SS 0003 Reinhard Nissl
2008-12-15 0:04 ` Greg KH
2008-12-21 19:11 ` Reinhard Nissl [this message]
-- strict thread matches above, loose matches on Subject: below --
2008-12-30 1:08 Roland
2008-12-31 16:14 ` James Bottomley
2008-12-07 12:54 [Fwd: mvsas determines most often an incorrect phy addr of 0 while attaching phy to port (Was: ERROR: Unidentified device type 0)] Reinhard Nissl
2008-12-10 23:31 ` PATCH: mvsas: increase port type detection delay to suit Seagate's 10k6 drive ST3450856SS 0003 Reinhard Nissl
2008-12-12 20:23 ` PATCH: mvsas: increase port type detection delay to suit Seagate's 15k6 " Reinhard Nissl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=494E94FF.3090809@gmx.de \
--to=rnissl@gmx.de \
--cc=akpm@linux-foundation.org \
--cc=greg@kroah.com \
--cc=linux-kernel@vger.kernel.org \
--cc=stable@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.