From: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
To: Krishna Kothapalli <krishna_sunitha@hotmail.com>
Cc: ebiederm@xmission.com, linux-pci@vger.kernel.org,
jbarnes@virtuousgeek.org, achiang@hp.com, djwong@us.ibm.com,
xyzzy@speakeasy.org, linux-kernel@vger.kernel.org
Subject: Re: Q: state of pci express hotplug
Date: Thu, 05 Feb 2009 15:42:26 +0900 [thread overview]
Message-ID: <498A8A52.9030606@jp.fujitsu.com> (raw)
In-Reply-To: <BAY111-W332E2827777D42F10C311E88C00@phx.gbl>
Hi,
Thank you for the information. From the information, I understood
both acpiphp and pciehp handles the same slot, and failed powering
on the slot because those drivers detected adapter card didn't
present or MRL opened. But I still don't know why. Could you send
the following addtional information?
(1) The whole 'lspci -vvv' output after booting the system with
your device inserted (not hot-plugging). Please do it as a
root user. And please also tell me which entry is corresponding
to your device in the output.
(2) Try hot-plugging with pciehp again with the following steps
and give me the result.
1. # /sbin/modprobe pciehp pciehp_debug
2. # pr -f /sys/bus/pci/slots/96/*
3. Insert the adapter card.
4. # echo 1 > /sys/bus/pci/slots/96/lock
5. wait for at least 1 second.
6. # pr -f /sys/bus/pci/slots/96/*
7. # echo 1 > /sys/bus/pci/slots/96/power
8. # pr -f /sys/bus/pci/slots/96/*
9. check if your device is added
Thanks,
Kenji Kaneshige
Krishna Kothapalli wrote:
>
>
> Tried echo power with pciehp, acpiphp. Aslo included dmidecode output. Not much luck yet. Thanks much.
>
>
>> Kenji Kaneshige
>> Could you try below after inserting the device?
>> With pciehp:
>> # echo 1> /sys/bus/pci/slots/96/power
>> With acpiphp:
>> # echo 1> /sys/bus/pci/slots/2/power
>
> with pciehp
> ----------------
> # uname -a
> Linux localhost.localdomain 2.6.28.3 #1 SMP Tue Feb 3 16:51:23 PST 2009 x86_64 x86_64 x86_64 GNU/Linux
>
> #/sbin/modprobe pciehp pciehp_debug
> [root@localhost test]# dmesg | grep pciehp
> pciehp 0000:00:09.0:pcie02: Hotplug Controller:
> pciehp 0000:00:09.0:pcie02: Seg/Bus/Dev/Func/IRQ : 0000:00:09.0 IRQ 2295
> pciehp 0000:00:09.0:pcie02: Vendor ID : 0x8086
> pciehp 0000:00:09.0:pcie02: Device ID : 0x3410
> pciehp 0000:00:09.0:pcie02: Subsystem ID : 0x0000
> pciehp 0000:00:09.0:pcie02: Subsystem Vendor ID : 0x0000
> pciehp 0000:00:09.0:pcie02: PCIe Cap offset : 0x90
> pciehp 0000:00:09.0:pcie02: Slot Capabilities : 0x0302005f
> pciehp 0000:00:09.0:pcie02: Physical Slot Number : 96
> pciehp 0000:00:09.0:pcie02: Attention Button : yes
> pciehp 0000:00:09.0:pcie02: Power Controller : yes
> pciehp 0000:00:09.0:pcie02: MRL Sensor : yes
> pciehp 0000:00:09.0:pcie02: Attention Indicator : yes
> pciehp 0000:00:09.0:pcie02: Power Indicator : yes
> pciehp 0000:00:09.0:pcie02: Hot-Plug Surprise : no
> pciehp 0000:00:09.0:pcie02: EMI Present : yes
> pciehp 0000:00:09.0:pcie02: Command Completed : yes
> pciehp 0000:00:09.0:pcie02: Slot Status : 0x0020
> pciehp 0000:00:09.0:pcie02: Slot Control : 0x078f
> pciehp 0000:00:09.0:pcie02: Link Active Reporting supported
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: HPC vendor_id 8086 device_id 3410 ss_vid 0 ss_did 0
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: Registering domain:bus:dev=0000:09:00 hp_slot=0 sun=60 slot_device_offset=0
> pciehp 0000:00:09.0:pcie02: get_power_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_get_power_status: SLOTCTRL a8 value read 7bf
> pciehp 0000:00:09.0:pcie02: get_attention_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_get_attention_status: SLOTCTRL a8, value read 7bf
> pciehp 0000:00:09.0:pcie02: get_latch_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: get_adapter_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_power_off_slot: slot->hp_slot 0
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: hpc_power_off_slot: SLOTCTRL a8 write cmd 400
> pciehp 0000:00:09.0:pcie02: service driver pciehp loaded
> pciehp: pcie_port_service_register = 0
> pciehp: PCI Express Hot Plug Controller Driver version: 0.4
>
> #insmod mvumi.ko
> # ls -lRt /sys/bus/pci/slots
> /sys/bus/pci/slots:
> total 0
> drwxr-xr-x 2 root root 0 2009-02-04 17:08 96
>
> /sys/bus/pci/slots/96:
> total 0
> -r--r--r-- 1 root root 4096 2009-02-04 17:10 adapter
> -r--r--r-- 1 root root 4096 2009-02-04 17:10 address
> -rw-r--r-- 1 root root 4096 2009-02-04 17:10 attention
> -r--r--r-- 1 root root 4096 2009-02-04 17:10 cur_bus_speed
> -r--r--r-- 1 root root 4096 2009-02-04 17:10 latch
> -rw-r--r-- 1 root root 4096 2009-02-04 17:10 lock
> -r--r--r-- 1 root root 4096 2009-02-04 17:10 max_bus_speed
> -rw-r--r-- 1 root root 4096 2009-02-04 17:10 power
> [root@localhost linux-2.0.4.9]#
>
>
> -- HOT plug the PCI Express card (some out put in dmesg!!)
>
> pciehp 0000:00:09.0:pcie02: enable_slot: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: Latch open on slot(96)
> pciehp 0000:00:09.0:pcie02: get_power_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_get_power_status: SLOTCTRL a8 value read 7b1
> pciehp 0000:00:09.0:pcie02: enable_slot: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: Latch open on slot(96)
> pciehp 0000:00:09.0:pcie02: enable_slot: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: No adapter on slot(96)
>
> [root@localhost linux-2.0.4.9]# lspci | wc
> 105 1284 9203 <-- same 105 devices as before
>
> # echo 1> /sys/bus/pci/slots/96/power
> bash: echo: write error: No such device
>
> [root@localhost linux-2.0.4.9]# lsmod | grep pciehp
> pciehp 42780 0
> [root@localhost linux-2.0.4.9]#
>
> #/sbin/rmmod pciehp
>
> #dmesg | grep pciehp
> ....
> pciehp: unload_pciehpd()
> pciehp 0000:00:09.0:pcie02: unloading service driver pciehp
> pciehp 0000:00:09.0:pcie02: release_slot: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: pcie_isr: intr_loc 8
> pciehp 0000:00:09.0:pcie02: Presence/Notify input change
> pciehp 0000:00:09.0:pcie02: Card not present on Slot(àt'?)
> pciehp: PCI Express Hot Plug Controller Driver version: 0.4 unloaded
>
>
> # ls -lt /sys/bus/pci/slots
> total 0
> #
>
> -- Remove PCI express card from the slot
>
> with modprobe pciehp pciehp_force=1 pciehp_debug
> ------------------------------------------------------
>
>> Mark Lord
>> Does it behave better with the pciehp_force=1 option?
>> modprobe pciehp pciehp_force=1
>
> # modprobe pciehp pciehp_force=1
> pciehp 0000:00:09.0:pcie02: Bypassing BIOS check for pciehp use on 0000:00:09.0
> pciehp 0000:00:09.0:pcie02: Link Active Reporting supported
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: HPC vendor_id 8086 device_id 3410 ss_vid 0 ss_did 0
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: Registering domain:bus:dev=0000:09:00 hp_slot=0 sun=60 slot_device_offset=0
> pci_create_slot: created pci_slot on 0000:09:00
> pciehp 0000:00:09.0:pcie02: get_power_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_get_power_status: SLOTCTRL a8 value read 7bf
> pciehp 0000:00:09.0:pcie02: get_attention_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_get_attention_status: SLOTCTRL a8, value read 7bf
> pciehp 0000:00:09.0:pcie02: get_latch_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: get_adapter_status: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: hpc_power_off_slot: slot->hp_slot 0
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp 0000:00:09.0:pcie02: hpc_power_off_slot: SLOTCTRL a8 write cmd 400
> pciehp 0000:00:09.0:pcie02: service driver pciehp loaded
> pciehp: PCI Express Hot Plug Controller Driver version: 0.4
>
> -- Insert PCI express card
>
> # lspci | wc
> 105 1284 9203 <-- number of devices did not increase
>
> # ls -lRtr /sys/bus/pci/slots
> /sys/bus/pci/slots:
> total 0
> drwxr-xr-x 2 root root 0 2009-02-04 17:27 96
>
> /sys/bus/pci/slots/96:
> total 0
> -rw-r--r-- 1 root root 4096 2009-02-04 17:31 power
> -r--r--r-- 1 root root 4096 2009-02-04 17:31 max_bus_speed
> -rw-r--r-- 1 root root 4096 2009-02-04 17:31 lock
> -r--r--r-- 1 root root 4096 2009-02-04 17:31 latch
> -r--r--r-- 1 root root 4096 2009-02-04 17:31 cur_bus_speed
> -rw-r--r-- 1 root root 4096 2009-02-04 17:31 attention
> -r--r--r-- 1 root root 4096 2009-02-04 17:31 address
> -r--r--r-- 1 root root 4096 2009-02-04 17:31 adapter
> [root@localhost linux-2.0.4.9]#
>
> # echo 1> /sys/bus/pci/slots/96/power
> bash: echo: write error: No such device
>
> -- remove PCI express card
>
>
> # /sbin/rmmod pciehp
> pciehp 0000:00:09.0:pcie02: enable_slot: physical_slot = 96
> pciehp 0000:00:09.0:pcie02: No adapter on slot(96)
> pciehp 0000:00:09.0:pcie02: unloading service driver pciehp
> pciehp 0000:00:09.0:pcie02: release_slot: physical_slot = 96
> pci_destroy_slot: dec refcount to 0 on 0000:09:00
> pci_slot_release: releasing pci_slot on 9:0
> pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec
> pciehp: PCI Express Hot Plug Controller Driver version: 0.4 unloaded
>
> with acpiphp
> -------------
>
> # lsmod | grep pciehp
>
> # /sbin/modprobe acpiphp debug
>
> acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
> acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:00:09.0
> acpiphp_glue: found ACPI PCI Hotplug slot 2 at PCI 0000:09:00
> pci_create_slot: created pci_slot on 0000:09:00
> acpiphp: Slot [2] registered
> acpiphp_glue: Bus 0000:09 has 1 slot
> acpiphp_glue: Total 1 slots
>
> # ls -lRt /sys/bus/pci/slots
> /sys/bus/pci/slots:
> total 0
> drwxr-xr-x 2 root root 0 2009-02-04 17:37 2
>
> /sys/bus/pci/slots/2:
> total 0
> -r--r--r-- 1 root root 4096 2009-02-04 17:38 adapter
> -r--r--r-- 1 root root 4096 2009-02-04 17:38 address
> -rw-r--r-- 1 root root 4096 2009-02-04 17:38 attention
> -r--r--r-- 1 root root 4096 2009-02-04 17:38 latch
> -rw-r--r-- 1 root root 4096 2009-02-04 17:38 power
>
> -- Insert PCI express card in the slot
>
> # ls -lRt /sys/bus/pci/slots
> /sys/bus/pci/slots:
> total 0
> drwxr-xr-x 2 root root 0 2009-02-04 17:37 2
>
> /sys/bus/pci/slots/2:
> total 0
> -r--r--r-- 1 root root 4096 2009-02-04 17:38 adapter
> -r--r--r-- 1 root root 4096 2009-02-04 17:38 address
> -rw-r--r-- 1 root root 4096 2009-02-04 17:38 attention
> -r--r--r-- 1 root root 4096 2009-02-04 17:38 latch
> -rw-r--r-- 1 root root 4096 2009-02-04 17:38 power
> #
>
> -- Insert PCI express card in the slot
>
> # echo 1> /sys/bus/pci/slots/2/power
> #
> acpiphp: enable_slot - physical_slot = 2
> acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
>
> # lspci | wc
> 105 1284 9203 <- same 105
>
>
>
> dmidecode
> --------------
>> Alex Chiang
>> Did we ever get a dmidecode from this machine?
>
>
> [root@localhost test]# /usr/sbin/dmidecode
> # dmidecode 2.9
> SMBIOS 2.4 present.
> 65 structures occupying 2483 bytes.
> Table at 0x3F6A3000.
>
> Handle 0x0000, DMI type 0, 24 bytes
> BIOS Information
> Vendor: INTEL
> Version: Txx047_CRB
> Release Date: Not Specified
> Address: 0xF0000
> Runtime Size: 64 kB
> ROM Size: 4096 kB
> Characteristics:
> PCI is supported
> PNP is supported
> BIOS is upgradeable
> BIOS shadowing is allowed
> Boot from CD is supported
> Selectable boot is supported
> EDD is supported
> 3.5"/2.88 MB floppy services are supported (int 13h)
> Print screen service is supported (int 5h)
> 8042 keyboard services are supported (int 9h)
> Serial services are supported (int 14h)
> CGA/mono video services are supported (int 10h)
> ACPI is supported
> USB legacy is supported
> LS-120 boot is supported
> ATAPI Zip drive boot is supported
> Function key-initiated network boot is supported
> Targeted content distribution is supported
> BIOS Revision: 24.22
> Firmware Revision: 0.0
>
> Handle 0x0001, DMI type 8, 9 bytes
> Port Connector Information
> Internal Reference Designator: J2H1
> Internal Connector Type: On Board IDE
> External Reference Designator: OnBoard Secondary IDE
> External Connector Type: None
> Port Type: Other
>
> Handle 0x0002, DMI type 13, 22 bytes
> BIOS Language Information
> Installable Languages: 2
> English
>
> Currently Installed Language: English
>
> Handle 0x0003, DMI type 12, 5 bytes
> System Configuration Options
> Option 1: J1D4:1-2,5-6,9-10Default;2-3CMOS clr,6-7Pswd clr,10-11Recovery
>
> Handle 0x0004, DMI type 16, 15 bytes
> Physical Memory Array
> Location: System Board Or Motherboard
> Use: System Memory
> Error Correction Type: Single-bit ECC
> Maximum Capacity: 192 GB
> Error Information Handle: Not Provided
> Number Of Devices: 18
>
> Handle 0x0005, DMI type 19, 15 bytes
> Memory Array Mapped Address
> Starting Address: 0x00000000000
> Ending Address: 0x0003FFFFFFF
> Range Size: 1 GB
> Physical Array Handle: 0x0004
> Partition Width: 0
>
> Handle 0x0006, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: J2MY
> Bank Locator: BRANCH 0 CHANNEL 0 DIMM 0
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0007, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: J1MY
> Bank Locator: BRANCH 0 CHANNEL 0 DIMM 1
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0008, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: J5MY
> Bank Locator: BRANCH 0 CHANNEL 1 DIMM 0
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0009, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: J3MY
> Bank Locator: BRANCH 0 CHANNEL 1 DIMM 1
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x000A, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: J6MY
> Bank Locator: BRANCH 1 CHANNEL 0 DIMM 0
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x000B, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: J4MY
> Bank Locator: BRANCH 1 CHANNEL 0 DIMM 1
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x000C, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: Not Specified
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x000D, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: Not Specified
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x000E, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: J2MY
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x000F, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: J1MY
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0010, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: J5MY
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0011, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: J3MY
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0012, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: J6MY
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0013, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: J4MY
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0014, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: Not Specified
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0015, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: Not Specified
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0016, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: Not Specified
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0017, DMI type 17, 27 bytes
> Memory Device
> Array Handle: 0x0004
> Error Information Handle: Not Provided
> Total Width: Unknown
> Data Width: Unknown
> Size: No Module Installed
> Form Factor: DIMM
> Set: None
> Locator: Not Specified
> Bank Locator: Not Specified
> Type: DDR2
> Type Detail: Synchronous
> Speed: 800 MHz (1.2 ns)
> Manufacturer: NO DIMM
> Serial Number: NO DIMM
> Asset Tag: NO DIMM
> Part Number: NO DIMM
>
> Handle 0x0018, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2001 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x001C
> L2 Cache Handle: 0x001B
> L3 Cache Handle: 0x0019
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x0019, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x001A, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x001B, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x001C, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x001D, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2003 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x0021
> L2 Cache Handle: 0x0020
> L3 Cache Handle: 0x001E
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x001E, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x001F, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x0020, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x0021, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x0022, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2002 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x0026
> L2 Cache Handle: 0x0025
> L3 Cache Handle: 0x0023
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x0023, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x0024, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x0025, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x0026, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x0027, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2036 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x002B
> L2 Cache Handle: 0x002A
> L3 Cache Handle: 0x0028
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x0028, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x0029, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x002A, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x002B, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x002C, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2001 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x0030
> L2 Cache Handle: 0x002F
> L3 Cache Handle: 0x002D
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x002D, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x002E, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x002F, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x0030, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x0031, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2027 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x0035
> L2 Cache Handle: 0x0034
> L3 Cache Handle: 0x0032
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x0032, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x0033, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x0034, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x0035, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x0036, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2001 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x003A
> L2 Cache Handle: 0x0039
> L3 Cache Handle: 0x0037
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x0037, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x0038, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x0039, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x003A, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0x003B, DMI type 4, 35 bytes
> Processor Information
> Socket Designation: Not Specified
> Type: Central Processor
> Family: Xeon
> Manufacturer: Not Specified
> ID: A4 06 01 00 FF FB EB BF
> Signature: Type 0, Family 6, Model 26, Stepping 4
> Flags:
> FPU (Floating-point unit on-chip)
> VME (Virtual mode extension)
> DE (Debugging extension)
> PSE (Page size extension)
> TSC (Time stamp counter)
> MSR (Model specific registers)
> PAE (Physical address extension)
> MCE (Machine check exception)
> CX8 (CMPXCHG8 instruction supported)
> APIC (On-chip APIC hardware supported)
> SEP (Fast system call)
> MTRR (Memory type range registers)
> PGE (Page global enable)
> MCA (Machine check architecture)
> CMOV (Conditional move instruction supported)
> PAT (Page attribute table)
> PSE-36 (36-bit page size extension)
> CLFSH (CLFLUSH instruction supported)
> DS (Debug store)
> ACPI (ACPI supported)
> MMX (MMX technology supported)
> FXSR (Fast floating-point save and restore)
> SSE (Streaming SIMD extensions)
> SSE2 (Streaming SIMD extensions 2)
> SS (Self-snoop)
> HTT (Hyper-threading technology)
> TM (Thermal monitor supported)
> PBE (Pending break enabled)
> Version: Not Specified
> Voltage: 1.2 V
> External Clock: Unknown
> Max Speed: 4000 MHz
> Current Speed: 2052 MHz
> Status: Populated, Enabled
> Upgrade: ZIF Socket
> L1 Cache Handle: 0x003F
> L2 Cache Handle: 0x003E
> L3 Cache Handle: 0x003C
> Serial Number: Not Specified
> Asset Tag: Not Specified
> Part Number: Not Specified
>
> Handle 0x003C, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 3
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 8192 KB
> Maximum Size: 8192 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 16-way Set-associative
>
> Handle 0x003D, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Data
> Associativity: 8-way Set-associative
>
> Handle 0x003E, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 2
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 256 KB
> Maximum Size: 256 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Unified
> Associativity: 8-way Set-associative
>
> Handle 0x003F, DMI type 7, 19 bytes
> Cache Information
> Socket Designation: Not Specified
> Configuration: Enabled, Not Socketed, Level 1
> Operational Mode: Write Back
> Location: Internal
> Installed Size: 32 KB
> Maximum Size: 32 KB
> Supported SRAM Types:
> Asynchronous
> Installed SRAM Type: Asynchronous
> Speed: Unknown
> Error Correction Type: Single-bit ECC
> System Type: Instruction
> Associativity: 4-way Set-associative
>
> Handle 0xFEFF, DMI type 127, 4 bytes
> End Of Table
>
>
> _________________________________________________________________
> Windows Live™: Keep your life in sync.
> http://windowslive.com/explore?ocid=TXT_TAGLM_WL_t1_allup_explore_022009
>
next prev parent reply other threads:[~2009-02-05 6:42 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-31 7:01 Q: state of pci express hotplug Eric W. Biederman
2009-01-31 18:13 ` Rafael J. Wysocki
2009-02-02 2:19 ` Kenji Kaneshige
2009-02-02 17:15 ` Krishna Kothapalli
2009-02-03 0:51 ` Kenji Kaneshige
2009-02-03 20:48 ` Krishna Kothapalli
2009-02-04 2:32 ` Krishna Kothapalli
2009-02-04 5:51 ` Kenji Kaneshige
2009-02-04 18:17 ` Krishna Kothapalli
2009-02-04 19:40 ` Mark Lord
2009-02-04 23:49 ` Alex Chiang
2009-02-05 0:02 ` Kenji Kaneshige
2009-02-05 1:53 ` Krishna Kothapalli
2009-02-05 6:42 ` Kenji Kaneshige [this message]
2009-02-06 20:37 ` Krishna Kothapalli
2009-02-02 17:01 ` Alex Chiang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=498A8A52.9030606@jp.fujitsu.com \
--to=kaneshige.kenji@jp.fujitsu.com \
--cc=achiang@hp.com \
--cc=djwong@us.ibm.com \
--cc=ebiederm@xmission.com \
--cc=jbarnes@virtuousgeek.org \
--cc=krishna_sunitha@hotmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=xyzzy@speakeasy.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.