Xen cannot boot with pvops dom0

Xen cannot boot with pvops dom0

[Han, Weidong]

I tried with latest Xen unstable (c/s 19833) with latest pvops dom0 (commit 384a55c0). Booting will hang, following is the serial console output: 

(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
)
(XEN) Freed 128kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
(XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
(XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
(XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
(XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
(XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
(XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
(XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
(XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
(XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
(XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
(XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!


Did anyone meet this issue? Is there any difference on build and installation between pvops dom0 and 2.6.18 dom0? Following is my instructions, pls correct me if something is wrong. Appreciate in advance.
 
My build and installation instructions:
	- cd xen-unstable.hg
	- make world (linux-2.6-pvops.git will be cloned)
	- make install

My grub entry:
	title Xen - pvops
    		root (hd0,2)
    		kernel /boot/xen.gz dom0_mem=512m
    		module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3 console=tty0 console=ttyS0

I also tried build pvops dom0 manually as follows, but it doesn't help.
	- cd linux-2.6-pvops.git
	- make
	- make modules_install
	- make install


Regards,
Weidong

Re: Xen cannot boot with pvops dom0

[Jun Koi]

On Thu, Jun 25, 2009 at 6:20 PM, Han, Weidong<weidong.han@intel.com> wrote:
> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0 (commit 384a55c0). Booting will hang, following is the serial console output:
>
> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
> )
> (XEN) Freed 128kB init memory.
> mapping kernel into physical memory
> Xen: setup ISA identity maps
> about to get started...
> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
> (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
> (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>
>
> Did anyone meet this issue? Is there any difference on build and installation between pvops dom0 and 2.6.18 dom0? Following is my instructions, pls correct me if something is wrong. Appreciate in advance.
>
> My build and installation instructions:
>        - cd xen-unstable.hg
>        - make world (linux-2.6-pvops.git will be cloned)
>        - make install
>
> My grub entry:
>        title Xen - pvops
>                root (hd0,2)
>                kernel /boot/xen.gz dom0_mem=512m
>                module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3 console=tty0 console=ttyS0
>
> I also tried build pvops dom0 manually as follows, but it doesn't help.
>        - cd linux-2.6-pvops.git
>        - make
>        - make modules_install
>        - make install
>

I am not quite sure if that is the correct way to recompile kernel, as
sometimes I have some problems with Dom0 booting after that.

I usually recompile Dom0 kernel this way: (from the root directory)

# make linux-2.6-xen-config  (to configure kernel options)
# make linux-2.6-xen-build
# make linux-2.6-xen-install

Then dont forget to "mkinitramfs", of course

Thanks,
J

Re: Xen cannot boot with pvops dom0

[Patrick Colp]

I don't think this is an issue with out the kernel was compiled. In fact, 
all of the ways mentioned will build the pvops kernel properly. I have run 
into a similar problem with the kernel trying to add/remove/modify ioapic 
stuff as well (and have tried to compile the kernel in every possible way, 
but still get the same problem).

I have a feeling it is an issue with the pvops kernel ioapic code and have 
spent some time trying to track it down, but haven't found anything yet.

The XCI 2.6.27 kernel works, though, so if you're just looking for a more 
modern kernel than 2.6.18, then I suggest using that. Hopefully this issue 
can be resolved soon, though. I would prefer to develop against the pvops 
kernel now that it's been selected as the xen-unstable default kernel.


Patrick


Jun Koi wrote:
> On Thu, Jun 25, 2009 at 6:20 PM, Han, Weidong<weidong.han@intel.com> wrote:
>> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0 (commit 384a55c0). Booting will hang, following is the serial console output:
>>
>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
>> )
>> (XEN) Freed 128kB init memory.
>> mapping kernel into physical memory
>> Xen: setup ISA identity maps
>> about to get started...
>> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
>> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
>> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
>> (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16 (and in fact, doing a make world/install will
>> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
>> (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>>
>>
>> Did anyone meet this issue? Is there any difference on build and installation between pvops dom0 and 2.6.18 dom0? Following is my instructions, pls correct me if something is wrong. Appreciate in advance.
>>
>> My build and installation instructions:
>>        - cd xen-unstable.hg
>>        - make world (linux-2.6-pvops.git will be cloned)
>>        - make install
>>
>> My grub entry:
>>        title Xen - pvops
>>                root (hd0,2)
>>                kernel /boot/xen.gz dom0_mem=512m
>>                module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3 console=tty0 console=ttyS0
>>
>> I also tried build pvops dom0 manually as follows, but it doesn't help.
>>        - cd linux-2.6-pvops.git
>>        - make
>>        - make modules_install
>>        - make install
>>
> 
> I am not quite sure if that is the correct way to recompile kernel, as
> sometimes I have some problems with Dom0 booting after that.
> 
> I usually recompile Dom0 kernel this way: (from the root directory)
> 
> # make linux-2.6-xen-config  (to configure kernel options)
> # make linux-2.6-xen-build
> # make linux-2.6-xen-install
> 
> Then dont forget to "mkinitramfs", of course
> 
> Thanks,
> J
> 
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel

Re: Xen cannot boot with pvops dom0

[Jeremy Fitzhardinge]

On 06/25/09 02:37, Patrick Colp wrote:
> I don't think this is an issue with out the kernel was compiled. In
> fact, all of the ways mentioned will build the pvops kernel properly.
> I have run into a similar problem with the kernel trying to
> add/remove/modify ioapic stuff as well (and have tried to compile the
> kernel in every possible way, but still get the same problem).
>
> I have a feeling it is an issue with the pvops kernel ioapic code and
> have spent some time trying to track it down, but haven't found
> anything yet.

Those messages are just noise, and are harmless.  They're the kernel's
core drivers trying to take over various pieces of important hardware
that Xen already owns.  So far it has just been easier to let the kernel
try and fail to take over the interrupts than to try to suppress the
messages.

    J

Re: Xen cannot boot with pvops dom0

[Patrick Colp]

Hmmm, OK. Well, something is still going wrong. I find that adding things like 
irqpoll and/or acpi=noirq seems to help a bit. By that I mean that it gets 
further into the boot process before stalling. If I wait a while and press 
random keys/buttons (like Num Lock or the power button), then that seems to coax 
it into booting a little bit more, but I've never managed to get it to 
completely boot. The furthest I got was to where it tries to read the root 
filesystem.

I could give you a dump of the boot-up messages, but aside from the ioapic 
stuff, there's nothing out of the ordinary.


Patrick


Jeremy Fitzhardinge wrote:
> On 06/25/09 02:37, Patrick Colp wrote:
>> I don't think this is an issue with out the kernel was compiled. In
>> fact, all of the ways mentioned will build the pvops kernel properly.
>> I have run into a similar problem with the kernel trying to
>> add/remove/modify ioapic stuff as well (and have tried to compile the
>> kernel in every possible way, but still get the same problem).
>>
>> I have a feeling it is an issue with the pvops kernel ioapic code and
>> have spent some time trying to track it down, but haven't found
>> anything yet.
> 
> Those messages are just noise, and are harmless.  They're the kernel's
> core drivers trying to take over various pieces of important hardware
> that Xen already owns.  So far it has just been easier to let the kernel
> try and fail to take over the interrupts than to try to suppress the
> messages.
> 
>     J

Re: Xen cannot boot with pvops dom0

[Jeremy Fitzhardinge]

On 07/01/09 00:32, Patrick Colp wrote:
> Hmmm, OK. Well, something is still going wrong. I find that adding
> things like irqpoll and/or acpi=noirq seems to help a bit. By that I
> mean that it gets further into the boot process before stalling. If I
> wait a while and press random keys/buttons (like Num Lock or the power
> button), then that seems to coax it into booting a little bit more,
> but I've never managed to get it to completely boot. The furthest I
> got was to where it tries to read the root filesystem.
>
> I could give you a dump of the boot-up messages, but aside from the
> ioapic stuff, there's nothing out of the ordinary.

Well, it suggests something is going wrong with interrupt routing. It
would be useful to get a full boot log for the kernel running both
native and as dom0 for comparison purposes.

    J

Re: Xen cannot boot with pvops dom0

[Patrick Colp]

[-- Attachment #1: Type: text/plain, Size: 960 bytes --]

I've attached the boot logs for a normal boot and a xen boot.


Patrick


Jeremy Fitzhardinge wrote:
> On 07/01/09 00:32, Patrick Colp wrote:
>> Hmmm, OK. Well, something is still going wrong. I find that adding
>> things like irqpoll and/or acpi=noirq seems to help a bit. By that I
>> mean that it gets further into the boot process before stalling. If I
>> wait a while and press random keys/buttons (like Num Lock or the power
>> button), then that seems to coax it into booting a little bit more,
>> but I've never managed to get it to completely boot. The furthest I
>> got was to where it tries to read the root filesystem.
>>
>> I could give you a dump of the boot-up messages, but aside from the
>> ioapic stuff, there's nothing out of the ordinary.
> 
> Well, it suggests something is going wrong with interrupt routing. It
> would be useful to get a full boot log for the kernel running both
> native and as dom0 for comparison purposes.
> 
>     J

[-- Attachment #2: normal-boot.log --]
[-- Type: text/x-log, Size: 116656 bytes --]

Jul  2 08:46:09 zumbi kernel: Inspecting /boot/System.map-2.6.30-rc6-tip
Jul  2 08:46:09 zumbi kernel: Cannot find map file.
Jul  2 08:46:09 zumbi kernel: Loaded 52141 symbols from 1 module.
Jul  2 08:46:09 zumbi kernel: [    0.000000] Initializing cgroup subsys cpuset
Jul  2 08:46:09 zumbi kernel: [    0.000000] Initializing cgroup subsys cpu
Jul  2 08:46:09 zumbi kernel: [    0.000000] Linux version 2.6.30-rc6-tip (t_patrickco@waitaha) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #5 SMP Fri Jun 26 16:33:19 BST 2009
Jul  2 08:46:09 zumbi kernel: [    0.000000] Command line: root=/dev/sda1 ro console=ttyS0 console=tty0
Jul  2 08:46:09 zumbi kernel: [    0.000000] KERNEL supported cpus:
Jul  2 08:46:09 zumbi kernel: [    0.000000]   Intel GenuineIntel
Jul  2 08:46:09 zumbi kernel: [    0.000000]   AMD AuthenticAMD
Jul  2 08:46:09 zumbi kernel: [    0.000000]   Centaur CentaurHauls
Jul  2 08:46:09 zumbi kernel: [    0.000000] BIOS-provided physical RAM map:
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 0000000000100000 - 000000009cf88000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009cf88000 - 000000009d106000 (ACPI NVS)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009d106000 - 000000009f6bd000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f6bd000 - 000000009f6bf000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f6bf000 - 000000009f714000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f714000 - 000000009f7bf000 (ACPI NVS)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f7bf000 - 000000009f7e1000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f7e1000 - 000000009f7ff000 (ACPI data)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f7ff000 - 000000009f800000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f800000 - 00000000b0000000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 00000000fc000000 - 00000000fd000000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  BIOS-e820: 0000000100000000 - 0000000160000000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000] DMI 2.5 present.
Jul  2 08:46:09 zumbi kernel: [    0.000000] last_pfn = 0x160000 max_arch_pfn = 0x400000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] MTRR default type: uncachable
Jul  2 08:46:09 zumbi kernel: [    0.000000] MTRR fixed ranges enabled:
Jul  2 08:46:09 zumbi kernel: [    0.000000]   00000-9FFFF write-back
Jul  2 08:46:09 zumbi kernel: [    0.000000]   A0000-BFFFF uncachable
Jul  2 08:46:09 zumbi kernel: [    0.000000]   C0000-DFFFF write-protect
Jul  2 08:46:09 zumbi kernel: [    0.000000]   E0000-FFFFF uncachable
Jul  2 08:46:09 zumbi kernel: [    0.000000] MTRR variable ranges enabled:
Jul  2 08:46:09 zumbi kernel: [    0.000000]   0 base 000000000 mask F80000000 write-back
Jul  2 08:46:09 zumbi kernel: [    0.000000]   1 base 080000000 mask FE0000000 write-back
Jul  2 08:46:09 zumbi kernel: [    0.000000]   2 base 100000000 mask F00000000 write-back
Jul  2 08:46:09 zumbi kernel: [    0.000000]   3 disabled
Jul  2 08:46:09 zumbi kernel: [    0.000000]   4 disabled
Jul  2 08:46:09 zumbi kernel: [    0.000000]   5 disabled
Jul  2 08:46:09 zumbi kernel: [    0.000000]   6 disabled
Jul  2 08:46:09 zumbi kernel: [    0.000000]   7 disabled
Jul  2 08:46:09 zumbi kernel: [    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [    0.000000] e820 update range: 00000000a0000000 - 0000000100000000 (usable) ==> (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000] last_pfn = 0x9f800 max_arch_pfn = 0x400000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000] Scanning 1 areas for low memory corruption
Jul  2 08:46:09 zumbi kernel: [    0.000000] modified physical RAM map:
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 0000000000000000 - 0000000000001000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 0000000000001000 - 0000000000006000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 0000000000006000 - 000000000009ec00 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000000009ec00 - 00000000000a0000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 00000000000e0000 - 0000000000100000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 0000000000100000 - 000000009cf88000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009cf88000 - 000000009d106000 (ACPI NVS)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009d106000 - 000000009f6bd000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f6bd000 - 000000009f6bf000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f6bf000 - 000000009f714000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f714000 - 000000009f7bf000 (ACPI NVS)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f7bf000 - 000000009f7e1000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f7e1000 - 000000009f7ff000 (ACPI data)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f7ff000 - 000000009f800000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 000000009f800000 - 00000000b0000000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 00000000fc000000 - 00000000fd000000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 00000000ffe00000 - 0000000100000000 (reserved)
Jul  2 08:46:09 zumbi kernel: [    0.000000]  modified: 0000000100000000 - 0000000160000000 (usable)
Jul  2 08:46:09 zumbi kernel: [    0.000000] initial memory mapped : 0 - 20000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] init_memory_mapping: 0000000000000000-000000009f800000
Jul  2 08:46:09 zumbi kernel: [    0.000000]  0000000000 - 009f800000 page 2M
Jul  2 08:46:09 zumbi kernel: [    0.000000] kernel direct mapping tables up to 9f800000 @ 8000-c000
Jul  2 08:46:09 zumbi kernel: [    0.000000] init_memory_mapping: 0000000100000000-0000000160000000
Jul  2 08:46:09 zumbi kernel: [    0.000000]  0100000000 - 0160000000 page 2M
Jul  2 08:46:09 zumbi kernel: [    0.000000] kernel direct mapping tables up to 160000000 @ a000-11000
Jul  2 08:46:09 zumbi kernel: [    0.000000] RAMDISK: 37c85000 - 37fef7b4
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: XSDT 000000009f7fe120 0006C (v01 INTEL  DX58SO   00000493      01000013)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: FACP 000000009f7fd000 000F4 (v03 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI Warning (tbfadt-0562): Optional field Pm2ControlBlock has zero address or length: 0000000000000450/0 [20090320]
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI Warning (tbfadt-0612): Invalid length for Pm2ControlBlock: 0, using default 8 [20090320]
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: DSDT 000000009f7f8000 043A2 (v02 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: FACS 000000009f727000 00040
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: APIC 000000009f7f7000 00138 (v02 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: WDDT 000000009f7f6000 00040 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: MCFG 000000009f7f5000 0003C (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: ASF! 000000009f7f4000 000AC (v32 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: SSDT 000000009f7e3000 0E134 (v01 INTEL  SSDT  PM 00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: DMAR 000000009f7e1000 00110 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: WDTT 000000009f7f2000 00164 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: ASPT 000000009f7f3000 00034 (v04 INTEL  PerfTune 00000493 MSFT 0100000D)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: Local APIC address 0xfee00000
Jul  2 08:46:09 zumbi kernel: [    0.000000] (8 early reservations) ==> bootmem [0000000000 - 0160000000]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #2 [0001000000 - 0001a42e08]    TEXT DATA BSS ==> [0001000000 - 0001a42e08]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #3 [0037c85000 - 0037fef7b4]          RAMDISK ==> [0037c85000 - 0037fef7b4]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #4 [000009ec00 - 0000100000]    BIOS reserved ==> [000009ec00 - 0000100000]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #5 [0001a43000 - 0001a430bc]              BRK ==> [0001a43000 - 0001a430bc]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #6 [0000008000 - 000000a000]          PGTABLE ==> [0000008000 - 000000a000]
Jul  2 08:46:09 zumbi kernel: [    0.000000]   #7 [000000a000 - 000000c000]          PGTABLE ==> [000000a000 - 000000c000]
Jul  2 08:46:09 zumbi kernel: [    0.000000] Zone PFN ranges:
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA      0x00000000 -> 0x00001000
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA32    0x00001000 -> 0x00100000
Jul  2 08:46:09 zumbi kernel: [    0.000000]   Normal   0x00100000 -> 0x00160000
Jul  2 08:46:09 zumbi kernel: [    0.000000] Movable zone start PFN for each node
Jul  2 08:46:09 zumbi kernel: [    0.000000] early_node_map[8] active PFN ranges
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x00000000 -> 0x00000001
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x00000006 -> 0x0000009e
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x00000100 -> 0x0009cf88
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x0009d106 -> 0x0009f6bd
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x0009f6bf -> 0x0009f714
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x0009f7bf -> 0x0009f7e1
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x0009f7ff -> 0x0009f800
Jul  2 08:46:09 zumbi kernel: [    0.000000]     0: 0x00100000 -> 0x00160000
Jul  2 08:46:09 zumbi kernel: [    0.000000] On node 0 totalpages: 1045840
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA zone: 56 pages used for memmap
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA zone: 104 pages reserved
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA zone: 3833 pages, LIFO batch:0
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA32 zone: 14280 pages used for memmap
Jul  2 08:46:09 zumbi kernel: [    0.000000]   DMA32 zone: 634351 pages, LIFO batch:31
Jul  2 08:46:09 zumbi kernel: [    0.000000]   Normal zone: 5376 pages used for memmap
Jul  2 08:46:09 zumbi kernel: [    0.000000]   Normal zone: 387840 pages, LIFO batch:31
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: PM-Timer IO Port: 0x408
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: Local APIC address 0xfee00000
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x01] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x03] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x05] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x07] enabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
Jul  2 08:46:09 zumbi kernel: [    0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: IRQ0 used by override.
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: IRQ2 used by override.
Jul  2 08:46:09 zumbi kernel: [    0.000000] ACPI: IRQ9 used by override.
Jul  2 08:46:09 zumbi kernel: [    0.000000] Using ACPI (MADT) for SMP configuration information
Jul  2 08:46:09 zumbi kernel: [    0.000000] 16 Processors exceeds NR_CPUS limit of 8
Jul  2 08:46:09 zumbi kernel: [    0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
Jul  2 08:46:09 zumbi kernel: [    0.000000] nr_irqs_gsi: 24
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009cf88000 - 000000009d106000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f6bd000 - 000000009f6bf000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f714000 - 000000009f7bf000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f7e1000 - 000000009f7ff000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f800000 - 00000000b0000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000b0000000 - 00000000fc000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fd000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000fd000000 - 00000000ffe00000
Jul  2 08:46:09 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
Jul  2 08:46:09 zumbi kernel: [    0.000000] Allocating PCI resources starting at b0000000 (gap: b0000000:4c000000)
Jul  2 08:46:09 zumbi kernel: [    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
Jul  2 08:46:09 zumbi kernel: [    0.000000] PERCPU: Embedded 28 pages at ffff880028028000, static data 83616 bytes
Jul  2 08:46:09 zumbi kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1026024
Jul  2 08:46:09 zumbi kernel: [    0.000000] Kernel command line: root=/dev/sda1 ro console=ttyS0 console=tty0
Jul  2 08:46:09 zumbi kernel: [    0.000000] Initializing CPU#0
Jul  2 08:46:09 zumbi kernel: [    0.000000] Experimental hierarchical RCU implementation.
Jul  2 08:46:09 zumbi kernel: [    0.000000] Experimental hierarchical RCU init done.
Jul  2 08:46:09 zumbi kernel: [    0.000000] NR_IRQS:4352 nr_irqs:472
Jul  2 08:46:09 zumbi kernel: [    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
Jul  2 08:46:09 zumbi kernel: [    0.000000] Extended CMOS year: 2000
Jul  2 08:46:09 zumbi kernel: [    0.000000] Fast TSC calibration using PIT
Jul  2 08:46:09 zumbi kernel: [    0.000000] Detected 2933.153 MHz processor.
Jul  2 08:46:09 zumbi kernel: [   37.014472] Console: colour VGA+ 80x25
Jul  2 08:46:09 zumbi kernel: [   37.014474] console [tty0] enabled
Jul  2 08:46:09 zumbi kernel: [   37.057894] console [ttyS0] enabled
Jul  2 08:46:09 zumbi kernel: [   37.148247] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Jul  2 08:46:09 zumbi kernel: [   37.149715] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Jul  2 08:46:09 zumbi kernel: [   37.150722] Checking aperture...
Jul  2 08:46:09 zumbi kernel: [   37.156716] No AGP bridge found
Jul  2 08:46:09 zumbi kernel: [   37.157134] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Jul  2 08:46:09 zumbi kernel: [   37.162788] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
Jul  2 08:46:09 zumbi kernel: [   37.163567] software IO TLB at phys 0x20000000 - 0x24000000
Jul  2 08:46:09 zumbi kernel: [   37.188407] Memory: 4037788k/5767168k available (5383k kernel code, 1583808k absent, 144664k reserved, 3284k data, 504k init)
Jul  2 08:46:09 zumbi kernel: [   37.194646] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Jul  2 08:46:09 zumbi kernel: [   37.195448] Calibrating delay loop (skipped), value calculated using timer frequency.. 5866.30 BogoMIPS (lpj=2933153)
Jul  2 08:46:09 zumbi kernel: [   37.196390] Security Framework initialized
Jul  2 08:46:09 zumbi kernel: [   37.196819] SELinux:  Initializing.
Jul  2 08:46:09 zumbi kernel: [   37.197220] SELinux:  Starting in permissive mode
Jul  2 08:46:09 zumbi kernel: [   37.197225] Mount-cache hash table entries: 256
Jul  2 08:46:09 zumbi kernel: [   37.197754] Initializing cgroup subsys ns
Jul  2 08:46:09 zumbi kernel: [   37.198173] Initializing cgroup subsys cpuacct
Jul  2 08:46:09 zumbi kernel: [   37.198613] Initializing cgroup subsys freezer
Jul  2 08:46:09 zumbi kernel: [   37.199054] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.199475] CPU: Processor Core ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.199879] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.200366] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.200755] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.201143] [ds] using Core i7 configuration
Jul  2 08:46:09 zumbi kernel: [   37.201575] [ds] sizes: address: 64 bit, bts/pebs record: 24/176 bytes
Jul  2 08:46:09 zumbi kernel: [   37.202139] using mwait in idle threads.
Jul  2 08:46:09 zumbi kernel: [   37.202558] Intel Performance Monitoring support detected.
Jul  2 08:46:09 zumbi kernel: [   37.203029] ... version:         3
Jul  2 08:46:09 zumbi kernel: [   37.203422] ... bit width:       48
Jul  2 08:46:09 zumbi kernel: [   37.203823] ... num counters:    4
Jul  2 08:46:09 zumbi kernel: [   37.204215] ... value mask:      0000ffffffffffff
Jul  2 08:46:09 zumbi kernel: [   37.204664] ... max period:      000000007fffffff
Jul  2 08:46:09 zumbi kernel: [   37.205107] ... fixed counters:  3
Jul  2 08:46:09 zumbi kernel: [   37.205506] ... counter mask:    000000070000000f
Jul  2 08:46:09 zumbi kernel: [   37.206614] ACPI: Core revision 20090320
Jul  2 08:46:09 zumbi kernel: [   37.219094] Setting APIC routing to flat
Jul  2 08:46:09 zumbi kernel: [   37.236000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
Jul  2 08:46:09 zumbi kernel: [   37.246560] CPU0: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.348447] Booting processor 1 APIC 0x2 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.359376] Initializing CPU#1
Jul  2 08:46:09 zumbi kernel: [   37.419344] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  2 08:46:09 zumbi kernel: [   37.419350] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.419351] CPU: Processor Core ID: 1
Jul  2 08:46:09 zumbi kernel: [   37.419353] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.419354] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.419355] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.419948] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.420557] CPU1: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.425453] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.426059] Booting processor 2 APIC 0x4 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.436878] Initializing CPU#2
Jul  2 08:46:09 zumbi kernel: [   37.497302] Calibrating delay using timer specific routine.. 5865.06 BogoMIPS (lpj=2932530)
Jul  2 08:46:09 zumbi kernel: [   37.497308] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.497309] CPU: Processor Core ID: 2
Jul  2 08:46:09 zumbi kernel: [   37.497311] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.497312] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.497313] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.497908] x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.498467] CPU2: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.503364] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.503970] Booting processor 3 APIC 0x6 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.514789] Initializing CPU#3
Jul  2 08:46:09 zumbi kernel: [   37.575260] Calibrating delay using timer specific routine.. 5865.06 BogoMIPS (lpj=2932530)
Jul  2 08:46:09 zumbi kernel: [   37.575266] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.575267] CPU: Processor Core ID: 3
Jul  2 08:46:09 zumbi kernel: [   37.575268] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.575270] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.575270] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.575865] x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.576479] CPU3: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.581380] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.581992] Booting processor 4 APIC 0x1 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.592812] Initializing CPU#4
Jul  2 08:46:09 zumbi kernel: [   37.653218] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  2 08:46:09 zumbi kernel: [   37.653225] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.653226] CPU: Processor Core ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.653228] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.653230] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.653231] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.653966] x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.654796] CPU4: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.659698] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.660309] Booting processor 5 APIC 0x3 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.671128] Initializing CPU#5
Jul  2 08:46:09 zumbi kernel: [   37.731176] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932528)
Jul  2 08:46:09 zumbi kernel: [   37.731181] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.731182] CPU: Processor Core ID: 1
Jul  2 08:46:09 zumbi kernel: [   37.731184] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.731185] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.731186] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.731973] x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.732821] CPU5: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.737722] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.738333] Booting processor 6 APIC 0x5 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.749151] Initializing CPU#6
Jul  2 08:46:09 zumbi kernel: [   37.809134] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  2 08:46:09 zumbi kernel: [   37.809139] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.809140] CPU: Processor Core ID: 2
Jul  2 08:46:09 zumbi kernel: [   37.809142] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.809143] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.809144] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.809927] x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.810713] CPU6: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.815608] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.816220] Booting processor 7 APIC 0x7 ip 0x6000
Jul  2 08:46:09 zumbi kernel: [   37.827040] Initializing CPU#7
Jul  2 08:46:09 zumbi kernel: [   37.887092] Calibrating delay using timer specific routine.. 5865.06 BogoMIPS (lpj=2932530)
Jul  2 08:46:09 zumbi kernel: [   37.887097] CPU: Physical Processor ID: 0
Jul  2 08:46:09 zumbi kernel: [   37.887098] CPU: Processor Core ID: 3
Jul  2 08:46:09 zumbi kernel: [   37.887100] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  2 08:46:09 zumbi kernel: [   37.887101] CPU: L2 cache: 256K
Jul  2 08:46:09 zumbi kernel: [   37.887102] CPU: L3 cache: 8192K
Jul  2 08:46:09 zumbi kernel: [   37.887885] x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
Jul  2 08:46:09 zumbi kernel: [   37.888737] CPU7: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  2 08:46:09 zumbi kernel: [   37.893639] Skipping synchronization checks as TSC is reliable.
Jul  2 08:46:09 zumbi kernel: [   37.894206] Brought up 8 CPUs
Jul  2 08:46:09 zumbi kernel: [   37.894620] Total of 8 processors activated (46921.71 BogoMIPS).
Jul  2 08:46:09 zumbi kernel: [   37.895416] khelper used greatest stack depth: 6024 bytes left
Jul  2 08:46:09 zumbi kernel: [   37.895481] net_namespace: 1832 bytes
Jul  2 08:46:09 zumbi kernel: [   37.896434] Booting paravirtualized kernel on bare hardware
Jul  2 08:46:09 zumbi kernel: [   37.897077] Time:  7:45:49  Date: 07/02/09
Jul  2 08:46:09 zumbi kernel: [   37.897579] NET: Registered protocol family 16
Jul  2 08:46:09 zumbi kernel: [   37.898153] err -19 in xenbus_probe_init
Jul  2 08:46:09 zumbi kernel: [   37.898729] ACPI: bus type pci registered
Jul  2 08:46:09 zumbi kernel: [   37.899270] PCI: MCFG configuration 0: base a0000000 segment 0 buses 0 - 255
Jul  2 08:46:09 zumbi kernel: [   37.899885] PCI: MCFG area at a0000000 reserved in E820
Jul  2 08:46:09 zumbi kernel: [   37.907726] PCI: Using MMCONFIG at a0000000 - afffffff
Jul  2 08:46:09 zumbi kernel: [   37.908249] PCI: Using configuration type 1 for base access
Jul  2 08:46:09 zumbi kernel: [   37.912333] bio: create slab <bio-0> at 0
Jul  2 08:46:09 zumbi kernel: [   37.913482] ACPI: EC: Look up EC in DSDT
Jul  2 08:46:09 zumbi kernel: [   37.929350] ACPI: Interpreter enabled
Jul  2 08:46:09 zumbi kernel: [   37.929798] ACPI: (supports S0 S1 S3 S4 S5)
Jul  2 08:46:09 zumbi kernel: [   37.930527] ACPI: Using IOAPIC for interrupt routing
Jul  2 08:46:09 zumbi kernel: [   37.935507] ACPI: No dock devices found.
Jul  2 08:46:09 zumbi kernel: [   37.935975] ACPI: PCI Root Bridge [PCI0] (0000:00)
Jul  2 08:46:09 zumbi kernel: [   37.936585] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.937156] pci 0000:00:01.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.937672] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.938241] pci 0000:00:03.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.938759] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.939328] pci 0000:00:07.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.940048] pci 0000:00:1a.0: reg 20 io port: [0x50c0-0x50df]
Jul  2 08:46:09 zumbi kernel: [   37.940110] pci 0000:00:1a.1: reg 20 io port: [0x50a0-0x50bf]
Jul  2 08:46:09 zumbi kernel: [   37.940170] pci 0000:00:1a.2: reg 20 io port: [0x5080-0x509f]
Jul  2 08:46:09 zumbi kernel: [   37.940228] pci 0000:00:1a.7: reg 10 32bit mmio: [0xb7201400-0xb72017ff]
Jul  2 08:46:09 zumbi kernel: [   37.940273] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.940843] pci 0000:00:1a.7: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.941364] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.941933] pci 0000:00:1c.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.942456] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.943024] pci 0000:00:1c.1: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.943550] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.944121] pci 0000:00:1c.4: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.944642] pci 0000:00:1d.0: reg 20 io port: [0x5060-0x507f]
Jul  2 08:46:09 zumbi kernel: [   37.944702] pci 0000:00:1d.1: reg 20 io port: [0x5040-0x505f]
Jul  2 08:46:09 zumbi kernel: [   37.944762] pci 0000:00:1d.2: reg 20 io port: [0x5020-0x503f]
Jul  2 08:46:09 zumbi kernel: [   37.944820] pci 0000:00:1d.7: reg 10 32bit mmio: [0xb7201000-0xb72013ff]
Jul  2 08:46:09 zumbi kernel: [   37.944864] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.945435] pci 0000:00:1d.7: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.951321] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
Jul  2 08:46:09 zumbi kernel: [   37.951325] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
Jul  2 08:46:09 zumbi kernel: [   37.952192] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
Jul  2 08:46:09 zumbi kernel: [   37.952800] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
Jul  2 08:46:09 zumbi kernel: [   37.953660] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
Jul  2 08:46:09 zumbi kernel: [   37.954567] pci 0000:00:1f.2: reg 10 io port: [0x5138-0x513f]
Jul  2 08:46:09 zumbi kernel: [   37.954572] pci 0000:00:1f.2: reg 14 io port: [0x514c-0x514f]
Jul  2 08:46:09 zumbi kernel: [   37.954577] pci 0000:00:1f.2: reg 18 io port: [0x5130-0x5137]
Jul  2 08:46:09 zumbi kernel: [   37.954581] pci 0000:00:1f.2: reg 1c io port: [0x5148-0x514b]
Jul  2 08:46:09 zumbi kernel: [   37.954586] pci 0000:00:1f.2: reg 20 io port: [0x5110-0x511f]
Jul  2 08:46:09 zumbi kernel: [   37.954590] pci 0000:00:1f.2: reg 24 io port: [0x5100-0x510f]
Jul  2 08:46:09 zumbi kernel: [   37.954630] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf0000000-0xf00000ff]
Jul  2 08:46:09 zumbi kernel: [   37.954641] pci 0000:00:1f.3: reg 20 io port: [0x5000-0x501f]
Jul  2 08:46:09 zumbi kernel: [   37.954678] pci 0000:00:1f.5: reg 10 io port: [0x5128-0x512f]
Jul  2 08:46:09 zumbi kernel: [   37.954683] pci 0000:00:1f.5: reg 14 io port: [0x5144-0x5147]
Jul  2 08:46:09 zumbi kernel: [   37.954687] pci 0000:00:1f.5: reg 18 io port: [0x5120-0x5127]
Jul  2 08:46:09 zumbi kernel: [   37.954692] pci 0000:00:1f.5: reg 1c io port: [0x5140-0x5143]
Jul  2 08:46:09 zumbi kernel: [   37.954697] pci 0000:00:1f.5: reg 20 io port: [0x50f0-0x50ff]
Jul  2 08:46:09 zumbi kernel: [   37.954701] pci 0000:00:1f.5: reg 24 io port: [0x50e0-0x50ef]
Jul  2 08:46:09 zumbi kernel: [   37.954784] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.955354] pci 0000:02:00.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.955847] pci 0000:00:03.0: bridge io port: [0x3000-0x4fff]
Jul  2 08:46:09 zumbi kernel: [   37.955850] pci 0000:00:03.0: bridge 32bit mmio: [0xb0000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.955854] pci 0000:00:03.0: bridge 64bit mmio pref: [0xd0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   37.955888] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.956456] pci 0000:03:00.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.956965] pci 0000:03:02.0: PME# supported from D0 D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.957534] pci 0000:03:02.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.958033] pci 0000:02:00.0: bridge io port: [0x3000-0x4fff]
Jul  2 08:46:09 zumbi kernel: [   37.958036] pci 0000:02:00.0: bridge 32bit mmio: [0xb0000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958040] pci 0000:02:00.0: bridge 64bit mmio pref: [0xd0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958072] pci 0000:04:00.0: reg 10 32bit mmio: [0xb6000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958081] pci 0000:04:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958090] pci 0000:04:00.0: reg 1c 64bit mmio: [0xb4000000-0xb5ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958095] pci 0000:04:00.0: reg 24 io port: [0x4000-0x407f]
Jul  2 08:46:09 zumbi kernel: [   37.958101] pci 0000:04:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958154] pci 0000:03:00.0: bridge io port: [0x4000-0x4fff]
Jul  2 08:46:09 zumbi kernel: [   37.958157] pci 0000:03:00.0: bridge 32bit mmio: [0xb4000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958161] pci 0000:03:00.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958192] pci 0000:05:00.0: reg 10 32bit mmio: [0xb2000000-0xb2ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958202] pci 0000:05:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958211] pci 0000:05:00.0: reg 1c 64bit mmio: [0xb0000000-0xb1ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958216] pci 0000:05:00.0: reg 24 io port: [0x3000-0x307f]
Jul  2 08:46:09 zumbi kernel: [   37.958222] pci 0000:05:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958276] pci 0000:03:02.0: bridge io port: [0x3000-0x3fff]
Jul  2 08:46:09 zumbi kernel: [   37.958279] pci 0000:03:02.0: bridge 32bit mmio: [0xb0000000-0xb2ffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958283] pci 0000:03:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
Jul  2 08:46:09 zumbi kernel: [   37.958450] pci 0000:08:00.0: reg 10 64bit mmio: [0xb7100000-0xb710ffff]
Jul  2 08:46:09 zumbi kernel: [   37.958515] pci 0000:08:00.0: PME# supported from D3hot D3cold
Jul  2 08:46:09 zumbi kernel: [   37.959120] pci 0000:08:00.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.959679] pci 0000:00:1c.1: bridge 32bit mmio: [0xb7100000-0xb71fffff]
Jul  2 08:46:09 zumbi kernel: [   37.959723] pci 0000:09:00.0: reg 10 io port: [0x2018-0x201f]
Jul  2 08:46:09 zumbi kernel: [   37.959730] pci 0000:09:00.0: reg 14 io port: [0x2024-0x2027]
Jul  2 08:46:09 zumbi kernel: [   37.959737] pci 0000:09:00.0: reg 18 io port: [0x2010-0x2017]
Jul  2 08:46:09 zumbi kernel: [   37.959744] pci 0000:09:00.0: reg 1c io port: [0x2020-0x2023]
Jul  2 08:46:09 zumbi kernel: [   37.959750] pci 0000:09:00.0: reg 20 io port: [0x2000-0x200f]
Jul  2 08:46:09 zumbi kernel: [   37.959757] pci 0000:09:00.0: reg 24 32bit mmio: [0xb7000000-0xb70003ff]
Jul  2 08:46:09 zumbi kernel: [   37.959794] pci 0000:09:00.0: supports D1
Jul  2 08:46:09 zumbi kernel: [   37.959796] pci 0000:09:00.0: PME# supported from D0 D1 D3hot
Jul  2 08:46:09 zumbi kernel: [   37.960350] pci 0000:09:00.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   37.960863] pci 0000:00:1c.4: bridge io port: [0x2000-0x2fff]
Jul  2 08:46:09 zumbi kernel: [   37.960866] pci 0000:00:1c.4: bridge 32bit mmio: [0xb7000000-0xb70fffff]
Jul  2 08:46:09 zumbi kernel: [   37.960891] pci 0000:0a:02.0: reg 10 io port: [0x1000-0x101f]
Jul  2 08:46:09 zumbi kernel: [   37.960958] pci 0000:00:1e.0: transparent bridge
Jul  2 08:46:09 zumbi kernel: [   37.961456] pci 0000:00:1e.0: bridge io port: [0x1000-0x1fff]
Jul  2 08:46:09 zumbi kernel: [   37.961483] pci_bus 0000:00: on NUMA node 0
Jul  2 08:46:09 zumbi kernel: [   37.961487] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.961973] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.962112] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.962172] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.962231] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.962291] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.962351] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
Jul  2 08:46:09 zumbi kernel: [   37.968189] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Jul  2 08:46:09 zumbi kernel: [   37.969751] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Jul  2 08:46:09 zumbi kernel: [   37.971314] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Jul  2 08:46:09 zumbi kernel: [   37.972878] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Jul  2 08:46:09 zumbi kernel: [   37.974440] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
Jul  2 08:46:09 zumbi kernel: [   37.976153] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Jul  2 08:46:09 zumbi kernel: [   37.977715] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
Jul  2 08:46:09 zumbi kernel: [   37.979428] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Jul  2 08:46:09 zumbi kernel: [   37.980987] xenbus_probe_backend_init bus registered ok
Jul  2 08:46:09 zumbi kernel: [   37.981534] xenbus_probe_frontend_init bus registered ok
Jul  2 08:46:09 zumbi kernel: [   37.982172] SCSI subsystem initialized
Jul  2 08:46:09 zumbi kernel: [   37.982705] libata version 3.00 loaded.
Jul  2 08:46:09 zumbi kernel: [   37.982839] usbcore: registered new interface driver usbfs
Jul  2 08:46:09 zumbi kernel: [   37.983398] usbcore: registered new interface driver hub
Jul  2 08:46:09 zumbi kernel: [   37.983955] usbcore: registered new device driver usb
Jul  2 08:46:09 zumbi kernel: [   37.984603] PCI: Using ACPI for IRQ routing
Jul  2 08:46:09 zumbi kernel: [   38.004077] cfg80211: Using static regulatory domain info
Jul  2 08:46:09 zumbi kernel: [   38.004617] cfg80211: Regulatory domain: US
Jul  2 08:46:09 zumbi kernel: [   38.005092] ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul  2 08:46:09 zumbi kernel: [   38.005934] ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
Jul  2 08:46:09 zumbi kernel: [   38.006536] ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  2 08:46:09 zumbi kernel: [   38.007139] ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  2 08:46:09 zumbi kernel: [   38.007741] ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  2 08:46:09 zumbi kernel: [   38.008343] ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  2 08:46:09 zumbi kernel: [   38.008945] ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
Jul  2 08:46:09 zumbi kernel: [   38.009548] NetLabel: Initializing
Jul  2 08:46:09 zumbi kernel: [   38.009983] NetLabel:  domain hash size = 128
Jul  2 08:46:09 zumbi kernel: [   38.010465] NetLabel:  protocols = UNLABELED CIPSOv4
Jul  2 08:46:09 zumbi kernel: [   38.010984] NetLabel:  unlabeled traffic allowed by default
Jul  2 08:46:09 zumbi kernel: [   38.011534] cfg80211: Calling CRDA for country: US
Jul  2 08:46:09 zumbi kernel: [   38.012174] hpet clockevent registered
Jul  2 08:46:09 zumbi kernel: [   38.012177] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
Jul  2 08:46:09 zumbi kernel: [   38.012796] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
Jul  2 08:46:09 zumbi kernel: [   38.013558] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
Jul  2 08:46:09 zumbi kernel: [   38.022036] Switched to high resolution mode on CPU 0
Jul  2 08:46:09 zumbi kernel: [   38.022159] Switched to high resolution mode on CPU 3
Jul  2 08:46:09 zumbi kernel: [   38.022161] Switched to high resolution mode on CPU 1
Jul  2 08:46:09 zumbi kernel: [   38.022163] Switched to high resolution mode on CPU 2
Jul  2 08:46:09 zumbi kernel: [   38.022526] Switched to high resolution mode on CPU 4
Jul  2 08:46:09 zumbi kernel: [   38.022589] Switched to high resolution mode on CPU 6
Jul  2 08:46:09 zumbi kernel: [   38.022592] Switched to high resolution mode on CPU 7
Jul  2 08:46:09 zumbi kernel: [   38.022614] Switched to high resolution mode on CPU 5
Jul  2 08:46:09 zumbi kernel: [   38.026039] pnp: PnP ACPI init
Jul  2 08:46:09 zumbi kernel: [   38.026468] ACPI: bus type pnp registered
Jul  2 08:46:09 zumbi kernel: [   38.028458] pnp: PnP ACPI: found 8 devices
Jul  2 08:46:09 zumbi kernel: [   38.028928] ACPI: ACPI bus type pnp unregistered
Jul  2 08:46:09 zumbi kernel: [   38.029430] system 00:05: ioport range 0x500-0x53f has been reserved
Jul  2 08:46:09 zumbi kernel: [   38.030012] system 00:05: ioport range 0x400-0x47f has been reserved
Jul  2 08:46:09 zumbi kernel: [   38.030594] system 00:05: ioport range 0x680-0x6ff has been reserved
Jul  2 08:46:09 zumbi kernel: [   38.036015] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
Jul  2 08:46:09 zumbi kernel: [   38.036576] pci 0000:00:01.0:   IO window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.037086] pci 0000:00:01.0:   MEM window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.037600] pci 0000:00:01.0:   PREFETCH window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.038137] pci 0000:04:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   38.039021] pci 0000:03:00.0: PCI bridge, secondary bus 0000:04
Jul  2 08:46:09 zumbi kernel: [   38.039581] pci 0000:03:00.0:   IO window: 0x4000-0x4fff
Jul  2 08:46:09 zumbi kernel: [   38.040113] pci 0000:03:00.0:   MEM window: 0xb4000000-0xb6ffffff
Jul  2 08:46:09 zumbi kernel: [   38.040681] pci 0000:03:00.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
Jul  2 08:46:09 zumbi kernel: [   38.041543] pci 0000:05:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
Jul  2 08:46:09 zumbi kernel: [   38.042428] pci 0000:03:02.0: PCI bridge, secondary bus 0000:05
Jul  2 08:46:09 zumbi kernel: [   38.042986] pci 0000:03:02.0:   IO window: 0x3000-0x3fff
Jul  2 08:46:09 zumbi kernel: [   38.043518] pci 0000:03:02.0:   MEM window: 0xb0000000-0xb2ffffff
Jul  2 08:46:09 zumbi kernel: [   38.044088] pci 0000:03:02.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
Jul  2 08:46:09 zumbi kernel: [   38.044950] pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
Jul  2 08:46:09 zumbi kernel: [   38.045510] pci 0000:02:00.0:   IO window: 0x3000-0x4fff
Jul  2 08:46:09 zumbi kernel: [   38.046042] pci 0000:02:00.0:   MEM window: 0xb0000000-0xb6ffffff
Jul  2 08:46:09 zumbi kernel: [   38.046612] pci 0000:02:00.0:   PREFETCH window: 0x000000d0000000-0x000000efffffff
Jul  2 08:46:09 zumbi kernel: [   38.047476] pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
Jul  2 08:46:09 zumbi kernel: [   38.048036] pci 0000:00:03.0:   IO window: 0x3000-0x4fff
Jul  2 08:46:09 zumbi kernel: [   38.048567] pci 0000:00:03.0:   MEM window: 0xb0000000-0xb6ffffff
Jul  2 08:46:09 zumbi kernel: [   38.049137] pci 0000:00:03.0:   PREFETCH window: 0x000000d0000000-0x000000efffffff
Jul  2 08:46:09 zumbi kernel: [   38.049997] pci 0000:00:07.0: PCI bridge, secondary bus 0000:06
Jul  2 08:46:09 zumbi kernel: [   38.050556] pci 0000:00:07.0:   IO window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.051066] pci 0000:00:07.0:   MEM window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.051577] pci 0000:00:07.0:   PREFETCH window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.052114] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:07
Jul  2 08:46:09 zumbi kernel: [   38.052672] pci 0000:00:1c.0:   IO window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.053182] pci 0000:00:1c.0:   MEM window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.053695] pci 0000:00:1c.0:   PREFETCH window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.054230] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:08
Jul  2 08:46:09 zumbi kernel: [   38.054789] pci 0000:00:1c.1:   IO window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.055300] pci 0000:00:1c.1:   MEM window: 0xb7100000-0xb71fffff
Jul  2 08:46:09 zumbi kernel: [   38.055868] pci 0000:00:1c.1:   PREFETCH window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.056407] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:09
Jul  2 08:46:09 zumbi kernel: [   38.056967] pci 0000:00:1c.4:   IO window: 0x2000-0x2fff
Jul  2 08:46:09 zumbi kernel: [   38.057500] pci 0000:00:1c.4:   MEM window: 0xb7000000-0xb70fffff
Jul  2 08:46:09 zumbi kernel: [   38.058070] pci 0000:00:1c.4:   PREFETCH window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.058604] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
Jul  2 08:46:09 zumbi kernel: [   38.059163] pci 0000:00:1e.0:   IO window: 0x1000-0x1fff
Jul  2 08:46:09 zumbi kernel: [   38.059695] pci 0000:00:1e.0:   MEM window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.060209] pci 0000:00:1e.0:   PREFETCH window: disabled
Jul  2 08:46:09 zumbi kernel: [   38.060748]   alloc irq_desc for 16 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.060749]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.060753] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  2 08:46:09 zumbi kernel: [   38.061352] pci 0000:00:01.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.061356] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  2 08:46:09 zumbi kernel: [   38.061954] pci 0000:00:03.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.061959] pci 0000:02:00.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.061963] pci 0000:03:00.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.061968] pci 0000:03:02.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.061972] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  2 08:46:09 zumbi kernel: [   38.062573] pci 0000:00:07.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.062577]   alloc irq_desc for 17 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.062578]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.062581] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jul  2 08:46:09 zumbi kernel: [   38.063182] pci 0000:00:1c.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.063186] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
Jul  2 08:46:09 zumbi kernel: [   38.063785] pci 0000:00:1c.1: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.063789] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jul  2 08:46:09 zumbi kernel: [   38.064389] pci 0000:00:1c.4: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.064394] pci 0000:00:1e.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.064396] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
Jul  2 08:46:09 zumbi kernel: [   38.064398] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064400] pci_bus 0000:02: resource 0 io:  [0x3000-0x4fff]
Jul  2 08:46:09 zumbi kernel: [   38.064402] pci_bus 0000:02: resource 1 mem: [0xb0000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064403] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064405] pci_bus 0000:03: resource 0 io:  [0x3000-0x4fff]
Jul  2 08:46:09 zumbi kernel: [   38.064406] pci_bus 0000:03: resource 1 mem: [0xb0000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064408] pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064409] pci_bus 0000:04: resource 0 io:  [0x4000-0x4fff]
Jul  2 08:46:09 zumbi kernel: [   38.064411] pci_bus 0000:04: resource 1 mem: [0xb4000000-0xb6ffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064413] pci_bus 0000:04: resource 2 pref mem [0xe0000000-0xefffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064414] pci_bus 0000:05: resource 0 io:  [0x3000-0x3fff]
Jul  2 08:46:09 zumbi kernel: [   38.064416] pci_bus 0000:05: resource 1 mem: [0xb0000000-0xb2ffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064417] pci_bus 0000:05: resource 2 pref mem [0xd0000000-0xdfffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064419] pci_bus 0000:08: resource 1 mem: [0xb7100000-0xb71fffff]
Jul  2 08:46:09 zumbi kernel: [   38.064421] pci_bus 0000:09: resource 0 io:  [0x2000-0x2fff]
Jul  2 08:46:09 zumbi kernel: [   38.064422] pci_bus 0000:09: resource 1 mem: [0xb7000000-0xb70fffff]
Jul  2 08:46:09 zumbi kernel: [   38.064424] pci_bus 0000:0a: resource 0 io:  [0x1000-0x1fff]
Jul  2 08:46:09 zumbi kernel: [   38.064425] pci_bus 0000:0a: resource 3 io:  [0x00-0xffff]
Jul  2 08:46:09 zumbi kernel: [   38.064427] pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffffffffffff]
Jul  2 08:46:09 zumbi kernel: [   38.064444] NET: Registered protocol family 2
Jul  2 08:46:09 zumbi kernel: [   38.071071] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Jul  2 08:46:09 zumbi kernel: [   38.072139] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
Jul  2 08:46:09 zumbi kernel: [   38.073576] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Jul  2 08:46:09 zumbi kernel: [   38.074320] TCP: Hash tables configured (established 262144 bind 65536)
Jul  2 08:46:09 zumbi kernel: [   38.074913] TCP reno registered
Jul  2 08:46:09 zumbi kernel: [   38.078111] NET: Registered protocol family 1
Jul  2 08:46:09 zumbi kernel: [   38.078634] Trying to unpack rootfs image as initramfs...
Jul  2 08:46:09 zumbi kernel: [   38.144397] Freeing initrd memory: 3497k freed
Jul  2 08:46:09 zumbi kernel: [   38.145505] kvm: already loaded the other module
Jul  2 08:46:09 zumbi kernel: [   38.146087] [ds] bts selftest...no resume progress/overflow...passed.
Jul  2 08:46:09 zumbi kernel: [   38.149638] microcode: CPU0 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.150225] microcode: CPU1 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.150808] microcode: CPU2 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.151394] microcode: CPU3 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.151978] microcode: CPU4 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.152568] microcode: CPU5 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.153153] microcode: CPU6 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.153736] microcode: CPU7 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  2 08:46:09 zumbi kernel: [   38.154342] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
Jul  2 08:46:09 zumbi kernel: [   38.155216] Scanning for low memory corruption every 60 seconds
Jul  2 08:46:09 zumbi kernel: [   38.155915] audit: initializing netlink socket (disabled)
Jul  2 08:46:09 zumbi kernel: [   38.156458] type=2000 audit(1246520748.834:1): initialized
Jul  2 08:46:09 zumbi kernel: [   38.167245] HugeTLB registered 2 MB page size, pre-allocated 0 pages
Jul  2 08:46:09 zumbi kernel: [   38.169421] VFS: Disk quotas dquot_6.5.2
Jul  2 08:46:09 zumbi kernel: [   38.169932] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Jul  2 08:46:09 zumbi kernel: [   38.171026] msgmni has been set to 7894
Jul  2 08:46:09 zumbi kernel: [   38.171551] SELinux:  Registering netfilter hooks
Jul  2 08:46:09 zumbi kernel: [   38.171820] alg: No test for stdrng (krng)
Jul  2 08:46:09 zumbi kernel: [   38.172349] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
Jul  2 08:46:09 zumbi kernel: [   38.173203] io scheduler noop registered
Jul  2 08:46:09 zumbi kernel: [   38.173662] io scheduler anticipatory registered
Jul  2 08:46:09 zumbi kernel: [   38.174158] io scheduler deadline registered
Jul  2 08:46:09 zumbi kernel: [   38.174641] io scheduler cfq registered (default)
Jul  2 08:46:09 zumbi kernel: [   38.175157] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10
Jul  2 08:46:09 zumbi kernel: [   38.175158] pci 0000:00:1a.0: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   38.175172] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010
Jul  2 08:46:09 zumbi kernel: [   38.175174] pci 0000:00:1a.1: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   38.175187] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010
Jul  2 08:46:09 zumbi kernel: [   38.175188] pci 0000:00:1a.2: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   38.175319] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
Jul  2 08:46:09 zumbi kernel: [   38.175321] pci 0000:00:1d.0: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   38.175334] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
Jul  2 08:46:09 zumbi kernel: [   38.175335] pci 0000:00:1d.1: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   38.175349] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
Jul  2 08:46:09 zumbi kernel: [   38.175350] pci 0000:00:1d.2: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   38.175513] pci 0000:05:00.0: Boot video device
Jul  2 08:46:09 zumbi kernel: [   38.175622]   alloc irq_desc for 24 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175623]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175629] pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   38.175638] pcieport-driver 0000:00:01.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.175746]   alloc irq_desc for 25 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175747]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175751] pcieport-driver 0000:00:03.0: irq 25 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   38.175759] pcieport-driver 0000:00:03.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.175862]   alloc irq_desc for 26 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175863]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175868] pcieport-driver 0000:00:07.0: irq 26 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   38.175875] pcieport-driver 0000:00:07.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.175985]   alloc irq_desc for 27 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175986]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.175991] pcieport-driver 0000:00:1c.0: irq 27 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   38.176002] pcieport-driver 0000:00:1c.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.176113]   alloc irq_desc for 28 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.176114]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.176120] pcieport-driver 0000:00:1c.1: irq 28 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   38.176130] pcieport-driver 0000:00:1c.1: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.176245]   alloc irq_desc for 29 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.176246]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.176251] pcieport-driver 0000:00:1c.4: irq 29 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   38.176261] pcieport-driver 0000:00:1c.4: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.176441] aer 0000:00:01.0:pcie02: AER service couldn't init device: no _OSC support
Jul  2 08:46:09 zumbi kernel: [   38.176445] aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support
Jul  2 08:46:09 zumbi kernel: [   38.176449] aer 0000:00:07.0:pcie02: AER service couldn't init device: no _OSC support
Jul  2 08:46:09 zumbi kernel: [   38.176467] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Jul  2 08:46:09 zumbi kernel: [   38.177166] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
Jul  2 08:46:09 zumbi kernel: [   38.178020] ACPI: Power Button [PWRF]
Jul  2 08:46:09 zumbi kernel: [   38.178519] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
Jul  2 08:46:09 zumbi kernel: [   38.179414] ACPI: Sleep Button [SLPB]
Jul  2 08:46:09 zumbi kernel: [   38.180314] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.181238]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.181728] Monitor-Mwait will be used to enter C-1 state
Jul  2 08:46:09 zumbi kernel: [   38.181744] Monitor-Mwait will be used to enter C-2 state
Jul  2 08:46:09 zumbi kernel: [   38.181757] Monitor-Mwait will be used to enter C-3 state
Jul  2 08:46:09 zumbi kernel: [   38.181787] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.182554] processor ACPI_CPU:00: registered as cooling_device0
Jul  2 08:46:09 zumbi kernel: [   38.183121] ACPI: Processor [CPU0] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.184166] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.185090]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.185640] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.186408] processor ACPI_CPU:02: registered as cooling_device1
Jul  2 08:46:09 zumbi kernel: [   38.186974] ACPI: Processor [CPU2] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.188026] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.188951]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.189504] ACPI: CPU2 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.195578] processor ACPI_CPU:04: registered as cooling_device2
Jul  2 08:46:09 zumbi kernel: [   38.196146] ACPI: Processor [CPU4] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.197195] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.198116]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.198668] ACPI: CPU3 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.199435] processor ACPI_CPU:06: registered as cooling_device3
Jul  2 08:46:09 zumbi kernel: [   38.200000] ACPI: Processor [CPU6] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.201049] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.201974]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.202524] ACPI: CPU4 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.203288] processor ACPI_CPU:08: registered as cooling_device4
Jul  2 08:46:09 zumbi kernel: [   38.203854] ACPI: Processor [CPU8] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.204899] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.205823]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.206365] ACPI: CPU5 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.207126] processor ACPI_CPU:0a: registered as cooling_device5
Jul  2 08:46:09 zumbi kernel: [   38.207694] ACPI: Processor [CPUA] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.208740] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.209663]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.210207] ACPI: CPU6 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.210970] processor ACPI_CPU:0c: registered as cooling_device6
Jul  2 08:46:09 zumbi kernel: [   38.211538] ACPI: Processor [CPUC] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.212586] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  2 08:46:09 zumbi kernel: [   38.213511]  [20090320]
Jul  2 08:46:09 zumbi kernel: [   38.214051] ACPI: CPU7 (power states: C1[C1] C2[C2] C3[C3])
Jul  2 08:46:09 zumbi kernel: [   38.214815] processor ACPI_CPU:0e: registered as cooling_device7
Jul  2 08:46:09 zumbi kernel: [   38.215381] ACPI: Processor [CPUE] (supports 8 throttling states)
Jul  2 08:46:09 zumbi kernel: [   38.217381] ***blkif_init
Jul  2 08:46:09 zumbi kernel: [   38.217780] *** netif_init
Jul  2 08:46:09 zumbi kernel: [   38.218181] xenfs: not registering filesystem on non-xen platform
Jul  2 08:46:09 zumbi kernel: [   38.220360] Non-volatile memory driver v1.3
Jul  2 08:46:09 zumbi kernel: [   38.220892] Linux agpgart interface v0.103
Jul  2 08:46:09 zumbi kernel: [   38.221414] [drm] Initialized drm 1.1.0 20060810
Jul  2 08:46:09 zumbi kernel: [   38.221949] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Jul  2 08:46:09 zumbi kernel: [   38.466006] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
Jul  2 08:46:09 zumbi kernel: [   38.466779]   alloc irq_desc for 18 on node -1
Jul  2 08:46:09 zumbi kernel: [   38.466780]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   38.466784] serial 0000:0a:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Jul  2 08:46:09 zumbi kernel: [   38.467473] 0000:0a:02.0: ttyS0 at I/O 0x1000 (irq = 18) is a 16550A
Jul  2 08:46:09 zumbi kernel: [   38.468402] 0000:0a:02.0: ttyS2 at I/O 0x1008 (irq = 18) is a 16550A
Jul  2 08:46:09 zumbi kernel: [   38.470194] brd: module loaded
Jul  2 08:46:09 zumbi kernel: [   38.471187] loop: module loaded
Jul  2 08:46:09 zumbi kernel: [   38.471774] input: Macintosh mouse button emulation as /devices/virtual/input/input2
Jul  2 08:46:09 zumbi kernel: [   38.473015] Driver 'sd' needs updating - please use bus_type methods
Jul  2 08:46:09 zumbi kernel: [   38.473868] Driver 'sr' needs updating - please use bus_type methods
Jul  2 08:46:09 zumbi kernel: [   38.474754] ahci 0000:09:00.0: version 3.0
Jul  2 08:46:09 zumbi kernel: [   38.474762] ahci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  2 08:46:09 zumbi kernel: [   38.475646] ahci 0000:09:00.0: controller can't do NCQ, turning off CAP_NCQ
Jul  2 08:46:09 zumbi kernel: [   38.476533] ahci 0000:09:00.0: controller can't do PMP, turning off CAP_PMP
Jul  2 08:46:09 zumbi kernel: [   38.477420] ahci 0000:09:00.0: MV_AHCI HACK: port_map 7 -> 3
Jul  2 08:46:09 zumbi kernel: [   38.478190] ahci 0000:09:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
Jul  2 08:46:09 zumbi kernel: [   38.479612] ahci: SSS flag set, parallel bus scan disabled
Jul  2 08:46:09 zumbi kernel: [   38.480398] ahci 0000:09:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
Jul  2 08:46:09 zumbi kernel: [   38.481598] ahci 0000:09:00.0: flags: 64bit stag led slum part 
Jul  2 08:46:09 zumbi kernel: [   38.482395] ahci 0000:09:00.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   38.482474] scsi0 : ahci
Jul  2 08:46:09 zumbi kernel: [   38.483041] scsi1 : ahci
Jul  2 08:46:09 zumbi kernel: [   38.483593] scsi2 : ahci
Jul  2 08:46:09 zumbi kernel: [   38.484134] ata1: SATA max UDMA/133 abar m1024@0xb7000000 port 0xb7000100 irq 16
Jul  2 08:46:09 zumbi kernel: [   38.485281] ata2: SATA max UDMA/133 abar m1024@0xb7000000 port 0xb7000180 irq 16
Jul  2 08:46:09 zumbi kernel: [   38.486426] ata3: DUMMY
Jul  2 08:46:09 zumbi kernel: [   38.791806] ata1: SATA link down (SStatus 0 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   39.096707] ata2: SATA link down (SStatus 0 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   39.097504] ata_piix 0000:00:1f.2: version 2.13
Jul  2 08:46:09 zumbi kernel: [   39.097509]   alloc irq_desc for 19 on node -1
Jul  2 08:46:09 zumbi kernel: [   39.097511]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   39.097514] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Jul  2 08:46:09 zumbi kernel: [   39.098424] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
Jul  2 08:46:09 zumbi kernel: [   39.099414] ata_piix 0000:00:1f.2: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   39.099446] scsi3 : ata_piix
Jul  2 08:46:09 zumbi kernel: [   39.100031] scsi4 : ata_piix
Jul  2 08:46:09 zumbi kernel: [   39.100661] ata4: SATA max UDMA/133 cmd 0x5138 ctl 0x514c bmdma 0x5110 irq 19
Jul  2 08:46:09 zumbi kernel: [   39.101567] ata5: SATA max UDMA/133 cmd 0x5130 ctl 0x5148 bmdma 0x5118 irq 19
Jul  2 08:46:09 zumbi kernel: [   39.862517] ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   39.863376] ata4.01: SATA link down (SStatus 0 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   39.882666] ata4.00: ATAPI: PIONEER BD-ROM  BDC-202, 1.04, max UDMA/66
Jul  2 08:46:09 zumbi kernel: [   39.889671] ata4.00: configured for UDMA/66
Jul  2 08:46:09 zumbi kernel: [   39.902874] scsi 3:0:0:0: CD-ROM            PIONEER  BD-ROM  BDC-202  1.04 PQ: 0 ANSI: 5
Jul  2 08:46:09 zumbi kernel: [   39.926143] sr0: scsi3-mmc drive: 32x/32x writer dvd-ram cd/rw xa/form2 cdda tray
Jul  2 08:46:09 zumbi kernel: [   39.927305] Uniform CD-ROM driver Revision: 3.20
Jul  2 08:46:09 zumbi kernel: [   39.928080] sr 3:0:0:0: Attached scsi CD-ROM sr0
Jul  2 08:46:09 zumbi kernel: [   39.928143] sr 3:0:0:0: Attached scsi generic sg0 type 5
Jul  2 08:46:09 zumbi kernel: [   40.689247] ata5.00: SATA link down (SStatus 0 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   40.690036] ata5.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   40.704780] ata5.01: ATA-8: ST3500320AS, SD15, max UDMA/133
Jul  2 08:46:09 zumbi kernel: [   40.705552] ata5.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Jul  2 08:46:09 zumbi kernel: [   40.711776] ata5.01: configured for UDMA/133
Jul  2 08:46:09 zumbi kernel: [   40.712475] scsi 4:0:1:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
Jul  2 08:46:09 zumbi kernel: [   40.713797] sd 4:0:1:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
Jul  2 08:46:09 zumbi kernel: [   40.714974] sd 4:0:1:0: [sda] Write Protect is off
Jul  2 08:46:09 zumbi kernel: [   40.715670] sd 4:0:1:0: [sda] Mode Sense: 00 3a 00 00
Jul  2 08:46:09 zumbi kernel: [   40.715683] sd 4:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul  2 08:46:09 zumbi kernel: [   40.717030]  sda: sda1 sda2 < sda5 >
Jul  2 08:46:09 zumbi kernel: [   40.754655] sd 4:0:1:0: [sda] Attached SCSI disk
Jul  2 08:46:09 zumbi kernel: [   40.755394] sd 4:0:1:0: Attached scsi generic sg1 type 0
Jul  2 08:46:09 zumbi kernel: [   40.756176] ata_piix 0000:00:1f.5: PCI INT B -> GSI 18 (level, low) -> IRQ 18
Jul  2 08:46:09 zumbi kernel: [   40.757083] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
Jul  2 08:46:09 zumbi kernel: [   40.758070] ata_piix 0000:00:1f.5: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   40.758105] scsi5 : ata_piix
Jul  2 08:46:09 zumbi kernel: [   40.758698] scsi6 : ata_piix
Jul  2 08:46:09 zumbi kernel: [   40.759311] ata6: SATA max UDMA/133 cmd 0x5128 ctl 0x5144 bmdma 0x50f0 irq 18
Jul  2 08:46:09 zumbi kernel: [   40.760218] ata7: SATA max UDMA/133 cmd 0x5120 ctl 0x5140 bmdma 0x50f8 irq 18
Jul  2 08:46:09 zumbi kernel: [   41.075846] ata6: SATA link down (SStatus 0 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   41.531962] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul  2 08:46:09 zumbi kernel: [   41.535499] ata7.00: ATA-8: ST3500320AS, SD15, max UDMA/133
Jul  2 08:46:09 zumbi kernel: [   41.536270] ata7.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Jul  2 08:46:09 zumbi kernel: [   41.543523] ata7.00: configured for UDMA/133
Jul  2 08:46:09 zumbi kernel: [   41.544214] scsi 6:0:0:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
Jul  2 08:46:09 zumbi kernel: [   41.545530] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
Jul  2 08:46:09 zumbi kernel: [   41.546708] sd 6:0:0:0: [sdb] Write Protect is off
Jul  2 08:46:09 zumbi kernel: [   41.547402] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Jul  2 08:46:09 zumbi kernel: [   41.547414] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul  2 08:46:09 zumbi kernel: [   41.548753]  sdb:
Jul  2 08:46:09 zumbi kernel: [   41.553099] sd 6:0:0:0: [sdb] Attached SCSI disk
Jul  2 08:46:09 zumbi kernel: [   41.553830] sd 6:0:0:0: Attached scsi generic sg2 type 0
Jul  2 08:46:09 zumbi kernel: [   41.554726] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
Jul  2 08:46:09 zumbi kernel: [   41.555568] Copyright (c) 1999-2006 Intel Corporation.
Jul  2 08:46:09 zumbi kernel: [   41.556320] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.4-k4
Jul  2 08:46:09 zumbi kernel: [   41.557130] e1000e: Copyright (c) 1999-2008 Intel Corporation.
Jul  2 08:46:09 zumbi kernel: [   41.557968] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
Jul  2 08:46:09 zumbi kernel: [   41.558778] e100: Copyright(c) 1999-2006 Intel Corporation
Jul  2 08:46:09 zumbi kernel: [   41.559565] tg3.c:v3.98 (February 25, 2009)
Jul  2 08:46:09 zumbi kernel: [   41.560257] tg3 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jul  2 08:46:09 zumbi kernel: [   41.561170] tg3 0000:08:00.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.561989] tg3 0000:08:00.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   41.567990] eth0: Tigon3 [partno(BCM95721A211F) rev 4201] (PCI Express) MAC address 00:10:18:32:51:a2
Jul  2 08:46:09 zumbi kernel: [   41.569297] eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
Jul  2 08:46:09 zumbi kernel: [   41.570459] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
Jul  2 08:46:09 zumbi kernel: [   41.571292] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
Jul  2 08:46:09 zumbi kernel: [   41.572069] sky2 driver version 1.22
Jul  2 08:46:09 zumbi kernel: [   41.572769] console [netcon0] enabled
Jul  2 08:46:09 zumbi kernel: [   41.573365] netconsole: network logging started
Jul  2 08:46:09 zumbi kernel: [   41.574118] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jul  2 08:46:09 zumbi kernel: [   41.574968] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
Jul  2 08:46:09 zumbi kernel: [   41.574980] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Jul  2 08:46:09 zumbi kernel: [   41.575891] ehci_hcd 0000:00:1a.7: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.575893] ehci_hcd 0000:00:1a.7: EHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.576659] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file 'devices'
Jul  2 08:46:09 zumbi kernel: [   41.576662] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.576693] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
Jul  2 08:46:09 zumbi kernel: [   41.577843] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
Jul  2 08:46:09 zumbi kernel: [   41.577846] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
Jul  2 08:46:09 zumbi kernel: [   41.577862] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  2 08:46:09 zumbi kernel: [   41.581757] ehci_hcd 0000:00:1a.7: debug port 1
Jul  2 08:46:09 zumbi kernel: [   41.582432] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
Jul  2 08:46:09 zumbi kernel: [   41.582434] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.582437] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xb7201400
Jul  2 08:46:09 zumbi kernel: [   41.583211] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  2 08:46:09 zumbi kernel: [   41.587091] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
Jul  2 08:46:09 zumbi kernel: [   41.591893] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
Jul  2 08:46:09 zumbi kernel: [   41.592689] usb usb1: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.592693] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jul  2 08:46:09 zumbi kernel: [   41.593566] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.594697] usb usb1: Product: EHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.595398] usb usb1: Manufacturer: Linux 2.6.30-rc6-tip ehci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.596208] usb usb1: SerialNumber: 0000:00:1a.7
Jul  2 08:46:09 zumbi kernel: [   41.596907] usb usb1: uevent
Jul  2 08:46:09 zumbi kernel: [   41.596930] usb usb1: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.596932] usb usb1: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.597698] usb usb1: adding 1-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.597707] usb 1-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.597727] hub 1-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.597729] hub 1-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.597730] hub 1-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.598336] hub 1-0:1.0: 6 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.598961] hub 1-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.598962] hub 1-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.598963] hub 1-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.598965] hub 1-0:1.0: power on to power good time: 20ms
Jul  2 08:46:09 zumbi kernel: [   41.598967] hub 1-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.598969] hub 1-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.599036] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.599078]   alloc irq_desc for 23 on node -1
Jul  2 08:46:09 zumbi kernel: [   41.599079]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   41.599083] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Jul  2 08:46:09 zumbi kernel: [   41.599994] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.599996] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.600755] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002'
Jul  2 08:46:09 zumbi kernel: [   41.600786] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
Jul  2 08:46:09 zumbi kernel: [   41.601936] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
Jul  2 08:46:09 zumbi kernel: [   41.601939] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
Jul  2 08:46:09 zumbi kernel: [   41.601950] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  2 08:46:09 zumbi kernel: [   41.605830] ehci_hcd 0000:00:1d.7: debug port 1
Jul  2 08:46:09 zumbi kernel: [   41.606505] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
Jul  2 08:46:09 zumbi kernel: [   41.606506] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.606515] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb7201000
Jul  2 08:46:09 zumbi kernel: [   41.607288] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  2 08:46:09 zumbi kernel: [   41.611164] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
Jul  2 08:46:09 zumbi kernel: [   41.615885] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Jul  2 08:46:09 zumbi kernel: [   41.616677] usb usb2: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.616681] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
Jul  2 08:46:09 zumbi kernel: [   41.617554] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.618684] usb usb2: Product: EHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.619385] usb usb2: Manufacturer: Linux 2.6.30-rc6-tip ehci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.620194] usb usb2: SerialNumber: 0000:00:1d.7
Jul  2 08:46:09 zumbi kernel: [   41.620893] usb usb2: uevent
Jul  2 08:46:09 zumbi kernel: [   41.620914] usb usb2: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.620915] usb usb2: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.621679] usb usb2: adding 2-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.621688] usb 2-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.621708] hub 2-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.621709] hub 2-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.621710] hub 2-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.622317] hub 2-0:1.0: 6 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.622941] hub 2-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.622941] hub 2-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.622943] hub 2-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.622944] hub 2-0:1.0: power on to power good time: 20ms
Jul  2 08:46:09 zumbi kernel: [   41.622946] hub 2-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.622948] hub 2-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.622995] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.623049] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jul  2 08:46:09 zumbi kernel: [   41.623866] ohci_hcd: block sizes: ed 80 td 96
Jul  2 08:46:09 zumbi kernel: [   41.623894] uhci_hcd: USB Universal Host Controller Interface driver
Jul  2 08:46:09 zumbi kernel: [   41.624739] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  2 08:46:09 zumbi kernel: [   41.625646] uhci_hcd 0000:00:1a.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.625648] uhci_hcd 0000:00:1a.0: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.626406] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '003'
Jul  2 08:46:09 zumbi kernel: [   41.626442] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
Jul  2 08:46:09 zumbi kernel: [   41.627592] uhci_hcd 0000:00:1a.0: detected 2 ports
Jul  2 08:46:09 zumbi kernel: [   41.628296] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
Jul  2 08:46:09 zumbi kernel: [   41.628297] uhci_hcd 0000:00:1a.0: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   41.628310] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.628313] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000050c0
Jul  2 08:46:09 zumbi kernel: [   41.634420] usb usb3: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.634424] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
Jul  2 08:46:09 zumbi kernel: [   41.635297] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.636426] usb usb3: Product: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.637127] usb usb3: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.637936] usb usb3: SerialNumber: 0000:00:1a.0
Jul  2 08:46:09 zumbi kernel: [   41.638633] usb usb3: uevent
Jul  2 08:46:09 zumbi kernel: [   41.638654] usb usb3: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.638656] usb usb3: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.639424] usb usb3: adding 3-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.639436] usb 3-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.639458] hub 3-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.639459] hub 3-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.639460] hub 3-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.640065] hub 3-0:1.0: 2 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.640688] hub 3-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.640689] hub 3-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.640690] hub 3-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.640691] hub 3-0:1.0: power on to power good time: 2ms
Jul  2 08:46:09 zumbi kernel: [   41.640694] hub 3-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.640695] hub 3-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.640730] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.640777]   alloc irq_desc for 21 on node -1
Jul  2 08:46:09 zumbi kernel: [   41.640778]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   41.640781] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
Jul  2 08:46:09 zumbi kernel: [   41.641689] uhci_hcd 0000:00:1a.1: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.641691] uhci_hcd 0000:00:1a.1: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.642449] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '004'
Jul  2 08:46:09 zumbi kernel: [   41.642480] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
Jul  2 08:46:09 zumbi kernel: [   41.643629] uhci_hcd 0000:00:1a.1: detected 2 ports
Jul  2 08:46:09 zumbi kernel: [   41.644333] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
Jul  2 08:46:09 zumbi kernel: [   41.644335] uhci_hcd 0000:00:1a.1: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   41.644347] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.644356] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000050a0
Jul  2 08:46:09 zumbi kernel: [   41.645152] usb usb4: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.645156] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
Jul  2 08:46:09 zumbi kernel: [   41.646028] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.647157] usb usb4: Product: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.647856] usb usb4: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.648665] usb usb4: SerialNumber: 0000:00:1a.1
Jul  2 08:46:09 zumbi kernel: [   41.649364] usb usb4: uevent
Jul  2 08:46:09 zumbi kernel: [   41.649385] usb usb4: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.649387] usb usb4: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.650152] usb usb4: adding 4-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.650160] usb 4-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.650182] hub 4-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.650183] hub 4-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.650184] hub 4-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.650787] hub 4-0:1.0: 2 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.651412] hub 4-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.651413] hub 4-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.651414] hub 4-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.651415] hub 4-0:1.0: power on to power good time: 2ms
Jul  2 08:46:09 zumbi kernel: [   41.651417] hub 4-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.651419] hub 4-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.651454] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.651501] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
Jul  2 08:46:09 zumbi kernel: [   41.652408] uhci_hcd 0000:00:1a.2: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.652410] uhci_hcd 0000:00:1a.2: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.653169] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '005'
Jul  2 08:46:09 zumbi kernel: [   41.653203] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
Jul  2 08:46:09 zumbi kernel: [   41.654353] uhci_hcd 0000:00:1a.2: detected 2 ports
Jul  2 08:46:09 zumbi kernel: [   41.655056] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
Jul  2 08:46:09 zumbi kernel: [   41.655058] uhci_hcd 0000:00:1a.2: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   41.655070] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.655073] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00005080
Jul  2 08:46:09 zumbi kernel: [   41.655869] usb usb5: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.655873] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
Jul  2 08:46:09 zumbi kernel: [   41.656744] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.657874] usb usb5: Product: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.658574] usb usb5: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.659384] usb usb5: SerialNumber: 0000:00:1a.2
Jul  2 08:46:09 zumbi kernel: [   41.660080] usb usb5: uevent
Jul  2 08:46:09 zumbi kernel: [   41.660102] usb usb5: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.660103] usb usb5: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.660871] usb usb5: adding 5-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.660879] usb 5-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.660900] hub 5-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.660902] hub 5-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.660903] hub 5-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.661505] hub 5-0:1.0: 2 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.662130] hub 5-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.662131] hub 5-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.662132] hub 5-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.662134] hub 5-0:1.0: power on to power good time: 2ms
Jul  2 08:46:09 zumbi kernel: [   41.662136] hub 5-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.662137] hub 5-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.662173] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.662219] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Jul  2 08:46:09 zumbi kernel: [   41.663126] uhci_hcd 0000:00:1d.0: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.663129] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.663890] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '006'
Jul  2 08:46:09 zumbi kernel: [   41.663922] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
Jul  2 08:46:09 zumbi kernel: [   41.665072] uhci_hcd 0000:00:1d.0: detected 2 ports
Jul  2 08:46:09 zumbi kernel: [   41.665773] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
Jul  2 08:46:09 zumbi kernel: [   41.665775] uhci_hcd 0000:00:1d.0: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   41.665787] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.665790] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00005060
Jul  2 08:46:09 zumbi kernel: [   41.666586] usb usb6: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.666590] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
Jul  2 08:46:09 zumbi kernel: [   41.667463] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.668591] usb usb6: Product: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.669292] usb usb6: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.670102] usb usb6: SerialNumber: 0000:00:1d.0
Jul  2 08:46:09 zumbi kernel: [   41.670799] usb usb6: uevent
Jul  2 08:46:09 zumbi kernel: [   41.670821] usb usb6: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.670822] usb usb6: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.671588] usb usb6: adding 6-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.671597] usb 6-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.671619] hub 6-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.671620] hub 6-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.671621] hub 6-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.672226] hub 6-0:1.0: 2 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.672850] hub 6-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.672850] hub 6-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.672852] hub 6-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.672853] hub 6-0:1.0: power on to power good time: 2ms
Jul  2 08:46:09 zumbi kernel: [   41.672855] hub 6-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.672858] hub 6-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.672893] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.672939] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Jul  2 08:46:09 zumbi kernel: [   41.673842] uhci_hcd 0000:00:1d.1: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.673845] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.674605] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '007'
Jul  2 08:46:09 zumbi kernel: [   41.674638] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
Jul  2 08:46:09 zumbi kernel: [   41.675788] uhci_hcd 0000:00:1d.1: detected 2 ports
Jul  2 08:46:09 zumbi kernel: [   41.676491] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
Jul  2 08:46:09 zumbi kernel: [   41.676493] uhci_hcd 0000:00:1d.1: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   41.676505] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.676508] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00005040
Jul  2 08:46:09 zumbi kernel: [   41.677305] usb usb7: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.677309] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
Jul  2 08:46:09 zumbi kernel: [   41.678182] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.679309] usb usb7: Product: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.680011] usb usb7: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.680818] usb usb7: SerialNumber: 0000:00:1d.1
Jul  2 08:46:09 zumbi kernel: [   41.681518] usb usb7: uevent
Jul  2 08:46:09 zumbi kernel: [   41.681539] usb usb7: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.681541] usb usb7: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.682307] usb usb7: adding 7-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.682316] usb 7-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.682337] hub 7-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.682339] hub 7-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.682340] hub 7-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.682944] hub 7-0:1.0: 2 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.683568] hub 7-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.683569] hub 7-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.683570] hub 7-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.683571] hub 7-0:1.0: power on to power good time: 2ms
Jul  2 08:46:09 zumbi kernel: [   41.683573] hub 7-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.683574] hub 7-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.683609] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.683658] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Jul  2 08:46:09 zumbi kernel: [   41.684565] uhci_hcd 0000:00:1d.2: setting latency timer to 64
Jul  2 08:46:09 zumbi kernel: [   41.684568] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.685326] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '008'
Jul  2 08:46:09 zumbi kernel: [   41.685362] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
Jul  2 08:46:09 zumbi kernel: [   41.686511] uhci_hcd 0000:00:1d.2: detected 2 ports
Jul  2 08:46:09 zumbi kernel: [   41.687215] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
Jul  2 08:46:09 zumbi kernel: [   41.687216] uhci_hcd 0000:00:1d.2: Performing full reset
Jul  2 08:46:09 zumbi kernel: [   41.687229] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
Jul  2 08:46:09 zumbi kernel: [   41.687232] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005020
Jul  2 08:46:09 zumbi kernel: [   41.688028] usb usb8: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   41.688032] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
Jul  2 08:46:09 zumbi kernel: [   41.688905] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  2 08:46:09 zumbi kernel: [   41.690035] usb usb8: Product: UHCI Host Controller
Jul  2 08:46:09 zumbi kernel: [   41.690732] usb usb8: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  2 08:46:09 zumbi kernel: [   41.691542] usb usb8: SerialNumber: 0000:00:1d.2
Jul  2 08:46:09 zumbi kernel: [   41.692240] usb usb8: uevent
Jul  2 08:46:09 zumbi kernel: [   41.692261] usb usb8: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   41.692263] usb usb8: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   41.693031] usb usb8: adding 8-0:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   41.693039] usb 8-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.693061] hub 8-0:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   41.693062] hub 8-0:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   41.693063] hub 8-0:1.0: USB hub found
Jul  2 08:46:09 zumbi kernel: [   41.693669] hub 8-0:1.0: 2 ports detected
Jul  2 08:46:09 zumbi kernel: [   41.694293] hub 8-0:1.0: standalone hub
Jul  2 08:46:09 zumbi kernel: [   41.694294] hub 8-0:1.0: no power switching (usb 1.0)
Jul  2 08:46:09 zumbi kernel: [   41.694295] hub 8-0:1.0: individual port over-current protection
Jul  2 08:46:09 zumbi kernel: [   41.694296] hub 8-0:1.0: power on to power good time: 2ms
Jul  2 08:46:09 zumbi kernel: [   41.694298] hub 8-0:1.0: local power source is good
Jul  2 08:46:09 zumbi kernel: [   41.694300] hub 8-0:1.0: trying to enable port power on non-switchable hub
Jul  2 08:46:09 zumbi kernel: [   41.694335] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  2 08:46:09 zumbi kernel: [   41.694423] usbcore: registered new interface driver usblp
Jul  2 08:46:09 zumbi kernel: [   41.695181] Initializing USB Mass Storage driver...
Jul  2 08:46:09 zumbi kernel: [   41.695922] usbcore: registered new interface driver usb-storage
Jul  2 08:46:09 zumbi kernel: [   41.696723] USB Mass Storage support registered.
Jul  2 08:46:09 zumbi kernel: [   41.697438] usbcore: registered new interface driver libusual
Jul  2 08:46:09 zumbi kernel: [   41.698243] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.698299] PNP: No PS/2 controller found. Probing ports directly.
Jul  2 08:46:09 zumbi kernel: [   41.701891] serio: i8042 KBD port at 0x60,0x64 irq 1
Jul  2 08:46:09 zumbi kernel: [   41.702604] serio: i8042 AUX port at 0x60,0x64 irq 12
Jul  2 08:46:09 zumbi kernel: [   41.703387] mice: PS/2 mouse device common for all mice
Jul  2 08:46:09 zumbi kernel: [   41.704298] rtc_cmos 00:02: RTC can wake from S4
Jul  2 08:46:09 zumbi kernel: [   41.705010] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
Jul  2 08:46:09 zumbi kernel: [   41.705840] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
Jul  2 08:46:09 zumbi kernel: [   41.706740] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
Jul  2 08:46:09 zumbi kernel: [   41.708022] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
Jul  2 08:46:09 zumbi kernel: [   41.709996] cpuidle: using governor ladder
Jul  2 08:46:09 zumbi kernel: [   41.711819] cpuidle: using governor menu
Jul  2 08:46:09 zumbi kernel: [   41.713015] usbcore: registered new interface driver hiddev
Jul  2 08:46:09 zumbi kernel: [   41.713807] usbcore: registered new interface driver usbhid
Jul  2 08:46:09 zumbi kernel: [   41.714620] usbhid: v2.6:USB HID core driver
Jul  2 08:46:09 zumbi kernel: [   41.715445] Advanced Linux Sound Architecture Driver Version 1.0.20.
Jul  2 08:46:09 zumbi kernel: [   41.718563] ALSA device list:
Jul  2 08:46:09 zumbi kernel: [   41.719146]   No soundcards found.
Jul  2 08:46:09 zumbi kernel: [   41.719737] Netfilter messages via NETLINK v0.30.
Jul  2 08:46:09 zumbi kernel: [   41.720485] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
Jul  2 08:46:09 zumbi kernel: [   41.721721] ctnetlink v0.93: registering with nfnetlink.
Jul  2 08:46:09 zumbi kernel: [   41.721852] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
Jul  2 08:46:09 zumbi kernel: [   41.721854] hub 2-0:1.0: port 1: status 0501 change 0001
Jul  2 08:46:09 zumbi kernel: [   41.721860] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
Jul  2 08:46:09 zumbi kernel: [   41.721862] hub 2-0:1.0: port 2: status 0501 change 0001
Jul  2 08:46:09 zumbi kernel: [   41.722875] ip_tables: (C) 2000-2006 Netfilter Core Team
Jul  2 08:46:09 zumbi kernel: [   41.723703] TCP cubic registered
Jul  2 08:46:09 zumbi kernel: [   41.724333] Initializing XFRM netlink socket
Jul  2 08:46:09 zumbi kernel: [   41.725558] NET: Registered protocol family 10
Jul  2 08:46:09 zumbi kernel: [   41.727058] ip6_tables: (C) 2000-2006 Netfilter Core Team
Jul  2 08:46:09 zumbi kernel: [   41.727882] IPv6 over IPv4 tunneling driver
Jul  2 08:46:09 zumbi kernel: [   41.729304] NET: Registered protocol family 17
Jul  2 08:46:09 zumbi kernel: [   41.730609] RPC: Registered udp transport module.
Jul  2 08:46:09 zumbi kernel: [   41.731348] RPC: Registered tcp transport module.
Jul  2 08:46:09 zumbi kernel: [   41.734862] PM: Resume from disk failed.
Jul  2 08:46:09 zumbi kernel: [   41.734870] registered taskstats version 1
Jul  2 08:46:09 zumbi kernel: [   41.735670]   Magic number: 1:132:773
Jul  2 08:46:09 zumbi kernel: [   41.736329] hub 2-0:1.0: hash matches
Jul  2 08:46:09 zumbi kernel: [   41.737044] Freeing unused kernel memory: 504k freed
Jul  2 08:46:09 zumbi kernel: [   41.737864] Write protecting the kernel read-only data: 7936k
Jul  2 08:46:09 zumbi kernel: [   41.739858] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.750951] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.761960] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.773157] uhci_hcd 0000:00:1d.0: port 1 portsc 008a,00
Jul  2 08:46:09 zumbi kernel: [   41.773168] uhci_hcd 0000:00:1d.0: port 2 portsc 008a,00
Jul  2 08:46:09 zumbi kernel: [   41.782942] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.793968] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.798826] console_setup used greatest stack depth: 5552 bytes left
Jul  2 08:46:09 zumbi kernel: [   41.822868] hub 2-0:1.0: state 7 ports 6 chg 0006 evt 0000
Jul  2 08:46:09 zumbi kernel: [   41.822877] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
Jul  2 08:46:09 zumbi kernel: [   41.822885] ehci_hcd 0000:00:1d.7: port 1 low speed --> companion
Jul  2 08:46:09 zumbi kernel: [   41.824006] usb usb3: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824018] usb 3-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824077] usb usb4: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824087] usb 4-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824140] usb usb5: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824151] usb 5-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824232] usb usb1: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824249] usb 1-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824543] usb usb6: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824554] usb 6-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824608] usb usb7: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824619] usb 7-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824673] usb usb8: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824684] usb 8-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824737] usb usb2: uevent
Jul  2 08:46:09 zumbi kernel: [   41.824747] usb 2-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   41.875188] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
Jul  2 08:46:09 zumbi kernel: [   41.875207] hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
Jul  2 08:46:09 zumbi kernel: [   41.875213] ehci_hcd 0000:00:1d.7: port 2 low speed --> companion
Jul  2 08:46:09 zumbi kernel: [   41.884995] scsi_id used greatest stack depth: 5504 bytes left
Jul  2 08:46:09 zumbi kernel: [   41.924189] vol_id used greatest stack depth: 5456 bytes left
Jul  2 08:46:09 zumbi kernel: [   41.927099] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
Jul  2 08:46:09 zumbi kernel: [   41.927117] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0004
Jul  2 08:46:09 zumbi kernel: [   41.927122] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0002
Jul  2 08:46:09 zumbi kernel: [   41.927128] uhci_hcd 0000:00:1d.0: port 1 portsc 01a3,00
Jul  2 08:46:09 zumbi kernel: [   41.927133] hub 6-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
Jul  2 08:46:09 zumbi kernel: [   41.932482] scsi_id used greatest stack depth: 5040 bytes left
Jul  2 08:46:09 zumbi kernel: [   42.029858] hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
Jul  2 08:46:09 zumbi kernel: [   42.061474] PM: Starting manual resume from disk
Jul  2 08:46:09 zumbi kernel: [   42.062355] PM: Resume from partition 8:5
Jul  2 08:46:09 zumbi kernel: [   42.062356] PM: Checking hibernation image.
Jul  2 08:46:09 zumbi kernel: [   42.062685] PM: Resume from disk failed.
Jul  2 08:46:09 zumbi kernel: [   42.110318] kjournald starting.  Commit interval 5 seconds
Jul  2 08:46:09 zumbi kernel: [   42.110333] EXT3-fs: mounted filesystem with writeback data mode.
Jul  2 08:46:09 zumbi kernel: [   42.131828] usb 6-1: new low speed USB device using uhci_hcd and address 2
Jul  2 08:46:09 zumbi kernel: [   42.274511] usb 6-1: skipped 1 descriptor after interface
Jul  2 08:46:09 zumbi kernel: [   42.279514] usb 6-1: default language 0x0409
Jul  2 08:46:09 zumbi kernel: [   42.296511] usb 6-1: New USB device found, idVendor=045e, idProduct=0083
Jul  2 08:46:09 zumbi kernel: [   42.297431] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Jul  2 08:46:09 zumbi kernel: [   42.298367] usb 6-1: Product: Basic Optical Mouse
Jul  2 08:46:09 zumbi kernel: [   42.299078] usb 6-1: Manufacturer: Microsoft
Jul  2 08:46:09 zumbi kernel: [   42.299803] usb 6-1: uevent
Jul  2 08:46:09 zumbi kernel: [   42.299812] usb 6-1: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   42.299814] usb 6-1: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   42.303511] usb 6-1: adding 6-1:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   42.303534] usb 6-1:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   42.303559] usbhid 6-1:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   42.303561] usbhid 6-1:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   42.316634] input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input3
Jul  2 08:46:09 zumbi kernel: [   42.318129] generic-usb 0003:045E:0083.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.0-1/input0
Jul  2 08:46:09 zumbi kernel: [   42.319807] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002'
Jul  2 08:46:09 zumbi kernel: [   42.319833] uhci_hcd 0000:00:1d.0: port 2 portsc 01a3,00
Jul  2 08:46:09 zumbi kernel: [   42.319838] hub 6-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
Jul  2 08:46:09 zumbi kernel: [   42.423756] hub 6-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
Jul  2 08:46:09 zumbi kernel: [   42.525672] usb 6-2: new low speed USB device using uhci_hcd and address 3
Jul  2 08:46:09 zumbi kernel: [   42.573213] runlevel used greatest stack depth: 4360 bytes left
Jul  2 08:46:09 zumbi kernel: [   42.671428] usb 6-2: skipped 1 descriptor after interface
Jul  2 08:46:09 zumbi kernel: [   42.671432] usb 6-2: skipped 1 descriptor after interface
Jul  2 08:46:09 zumbi kernel: [   42.671436] usb 6-2: New USB device found, idVendor=0566, idProduct=3002
Jul  2 08:46:09 zumbi kernel: [   42.672367] usb 6-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Jul  2 08:46:09 zumbi kernel: [   42.673378] usb 6-2: uevent
Jul  2 08:46:09 zumbi kernel: [   42.673386] usb 6-2: usb_probe_device
Jul  2 08:46:09 zumbi kernel: [   42.673387] usb 6-2: configuration #1 chosen from 1 choice
Jul  2 08:46:09 zumbi kernel: [   42.676427] usb 6-2: adding 6-2:1.0 (config #1, interface 0)
Jul  2 08:46:09 zumbi kernel: [   42.676450] usb 6-2:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   42.676474] usbhid 6-2:1.0: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   42.676476] usbhid 6-2:1.0: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   42.689564] input: HID 0566:3002 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input4
Jul  2 08:46:09 zumbi kernel: [   42.690910] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 118 us
Jul  2 08:46:09 zumbi kernel: [   42.690940] generic-usb 0003:0566:3002.0002: input,hidraw1: USB HID v1.10 Keyboard [HID 0566:3002] on usb-0000:00:1d.0-2/input0
Jul  2 08:46:09 zumbi kernel: [   42.692496] usb 6-2: adding 6-2:1.1 (config #1, interface 1)
Jul  2 08:46:09 zumbi kernel: [   42.692506] usb 6-2:1.1: uevent
Jul  2 08:46:09 zumbi kernel: [   42.692518] usbhid 6-2:1.1: usb_probe_interface
Jul  2 08:46:09 zumbi kernel: [   42.692519] usbhid 6-2:1.1: usb_probe_interface - got id
Jul  2 08:46:09 zumbi kernel: [   42.728554] input: HID 0566:3002 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/input/input5
Jul  2 08:46:09 zumbi kernel: [   42.735232] uhci_hcd 0000:00:1d.0: reserve dev 3 ep82-INT, period 8, phase 4, 93 us
Jul  2 08:46:09 zumbi kernel: [   42.735251] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/file.c: looking for a minor, starting at 96
Jul  2 08:46:09 zumbi kernel: [   42.735282] generic-usb 0003:0566:3002.0003: input,hiddev96,hidraw2: USB HID v1.10 Device [HID 0566:3002] on usb-0000:00:1d.0-2/input1
Jul  2 08:46:09 zumbi kernel: [   42.736904] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '003'
Jul  2 08:46:09 zumbi kernel: [   42.736928] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  2 08:46:09 zumbi kernel: [   42.774584] usb usb3: suspend_rh (auto-stop)
Jul  2 08:46:09 zumbi kernel: [   42.774606] usb usb4: suspend_rh (auto-stop)
Jul  2 08:46:09 zumbi kernel: [   42.774627] usb usb5: suspend_rh (auto-stop)
Jul  2 08:46:09 zumbi kernel: [   42.774647] usb usb7: suspend_rh (auto-stop)
Jul  2 08:46:09 zumbi kernel: [   42.774667] usb usb8: suspend_rh (auto-stop)
Jul  2 08:46:09 zumbi kernel: [   44.009212] hub 1-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009221] usb usb1: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009223] ehci_hcd 0000:00:1a.7: suspend root hub
Jul  2 08:46:09 zumbi kernel: [   44.009245] hub 3-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009249] usb usb3: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009251] usb usb3: suspend_rh
Jul  2 08:46:09 zumbi kernel: [   44.009266] hub 4-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009269] usb usb4: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009271] usb usb4: suspend_rh
Jul  2 08:46:09 zumbi kernel: [   44.009286] hub 5-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009288] usb usb5: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009290] usb usb5: suspend_rh
Jul  2 08:46:09 zumbi kernel: [   44.009302] hub 7-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009304] usb usb7: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009305] usb usb7: suspend_rh
Jul  2 08:46:09 zumbi kernel: [   44.009318] hub 8-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009319] usb usb8: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009321] usb usb8: suspend_rh
Jul  2 08:46:09 zumbi kernel: [   44.009333] hub 2-0:1.0: hub_suspend
Jul  2 08:46:09 zumbi kernel: [   44.009335] usb usb2: bus auto-suspend
Jul  2 08:46:09 zumbi kernel: [   44.009336] ehci_hcd 0000:00:1d.7: suspend root hub
Jul  2 08:46:09 zumbi kernel: [   46.852921] udevd version 124 started
Jul  2 08:46:09 zumbi kernel: [   46.852954] udevd used greatest stack depth: 4288 bytes left
Jul  2 08:46:09 zumbi kernel: [   46.875784] usb usb3: uevent
Jul  2 08:46:09 zumbi kernel: [   46.875817] usb 3-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.875982] usb usb4: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876016] usb 4-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876176] usb usb5: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876197] usb 5-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876344] usb usb1: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876377] usb 1-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876959] usb usb6: uevent
Jul  2 08:46:09 zumbi kernel: [   46.876979] usb 6-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877018] usb 6-1: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877031] usb 6-1:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877156] usb 6-2: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877169] usb 6-2:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877256] usb 6-2:1.1: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877453] usb usb7: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877465] usb 7-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877536] usb usb8: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877547] usb 8-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877634] usb usb2: uevent
Jul  2 08:46:09 zumbi kernel: [   46.877666] usb 2-0:1.0: uevent
Jul  2 08:46:09 zumbi kernel: [   47.772060] Adding 11847896k swap on /dev/sda5.  Priority:-1 extents:1 across:11847896k 
Jul  2 08:46:09 zumbi kernel: [   48.115785] EXT3 FS on sda1, internal journal
Jul  2 08:46:09 zumbi kernel: [   48.505539] tg3 0000:08:00.0: PME# disabled
Jul  2 08:46:09 zumbi kernel: [   48.506007]   alloc irq_desc for 30 on node -1
Jul  2 08:46:09 zumbi kernel: [   48.506009]   alloc kstat_irqs on node -1
Jul  2 08:46:09 zumbi kernel: [   48.506065] tg3 0000:08:00.0: irq 30 for MSI/MSI-X
Jul  2 08:46:09 zumbi kernel: [   48.593804] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jul  2 08:46:09 zumbi kernel: [   51.605980] tg3: eth0: Link is up at 1000 Mbps, full duplex.
Jul  2 08:46:09 zumbi kernel: [   51.605982] tg3: eth0: Flow control is off for TX and off for RX.
Jul  2 08:46:09 zumbi kernel: [   51.606459] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jul  2 08:46:09 zumbi kernel: [   57.214830] svc: failed to register lockdv1 RPC service (errno 97).
Jul  2 08:46:09 zumbi kernel: [   57.216647] mount.nfs used greatest stack depth: 3328 bytes left
Jul  2 08:46:09 zumbi kernel: [   58.606949] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
Jul  2 08:46:13 zumbi kernel: [   62.325297] eth0: no IPv6 routers present

[-- Attachment #3: xen-boot.log --]
[-- Type: text/x-log, Size: 87868 bytes --]

 __  __            _____  ____                     _        _     _      
 \ \/ /___ _ __   |___ / | ___|    _   _ _ __  ___| |_ __ _| |__ | | ___ 
  \  // _ \ '_ \    |_ \ |___ \ __| | | | '_ \/ __| __/ _` | '_ \| |/ _ \
  /  \  __/ | | |  ___) | ___) |__| |_| | | | \__ \ || (_| | |_) | |  __/
 /_/\_\___|_| |_| |____(_)____/    \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
                                                                         
(XEN) Xen version 3.5-unstable (t_patrickco@uk.xensource.com) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) Wed Jul  1 09:04:26 BST 2009
(XEN) Latest ChangeSet: Wed Jun 24 11:47:04 2009 +0100 19822:e904a8601aff
(XEN) Command line: dom0_mem=768M dom0_max_vcpus=1 loglvl=all guest_loglvl=all com1=115200/921600,8n1,0x1000,0 console=com1,vga
(XEN) Video information:
(XEN)  VGA is text mode 80x25, font 8x16
(XEN)  VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN)  EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN)  Found 2 MBR signatures
(XEN)  Found 2 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN)  0000000000000000 - 000000000009ec00 (usable)
(XEN)  000000000009ec00 - 00000000000a0000 (reserved)
(XEN)  00000000000e0000 - 0000000000100000 (reserved)
(XEN)  0000000000100000 - 000000009cf88000 (usable)
(XEN)  000000009cf88000 - 000000009d106000 (ACPI NVS)
(XEN)  000000009d106000 - 000000009f6bd000 (usable)
(XEN)  000000009f6bd000 - 000000009f6bf000 (reserved)
(XEN)  000000009f6bf000 - 000000009f714000 (usable)
(XEN)  000000009f714000 - 000000009f7bf000 (ACPI NVS)
(XEN)  000000009f7bf000 - 000000009f7e1000 (usable)
(XEN)  000000009f7e1000 - 000000009f7ff000 (ACPI data)
(XEN)  000000009f7ff000 - 000000009f800000 (usable)
(XEN)  000000009f800000 - 00000000b0000000 (reserved)
(XEN)  00000000fc000000 - 00000000fd000000 (reserved)
(XEN)  00000000ffe00000 - 0000000100000000 (reserved)
(XEN)  0000000100000000 - 0000000160000000 (usable)
(XEN) System RAM: 4085MB (4183380kB)
(XEN) ACPI: RSDP 000FE020, 0024 (r2 INTEL )
(XEN) ACPI: XSDT 9F7FE120, 006C (r1 INTEL  DX58SO        493       1000013)
(XEN) ACPI: FACP 9F7FD000, 00F4 (r3 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI Warning (tbfadt-0444): Optional field "Pm2ControlBlock" has zero address or length: 0000000000000450/0 [20070126]
(XEN) ACPI: DSDT 9F7F8000, 43A2 (r2 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: FACS 9F727000, 0040
(XEN) ACPI: APIC 9F7F7000, 0138 (r2 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: WDDT 9F7F6000, 0040 (r1 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: MCFG 9F7F5000, 003C (r1 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: ASF! 9F7F4000, 00AC (r32 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: SSDT 9F7E3000, E134 (r1 INTEL  SSDT  PM      493 MSFT  100000D)
(XEN) ACPI: DMAR 9F7E1000, 0110 (r1 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: WDTT 9F7F2000, 0164 (r1 INTEL  DX58SO        493 MSFT  100000D)
(XEN) ACPI: ASPT 9F7F3000, 0034 (r4 INTEL  PerfTune      493 MSFT  100000D)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-0000000160000000
(XEN) Domain heap initialised
(XEN) DMI 2.5 present.
(XEN) Using APIC driver x2apic
(XEN) x2APIC mode enabled.
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI:                  wakeup_vec[9f72700c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
(XEN) Processor #0 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) Processor #2 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
(XEN) Processor #6 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x01] enabled)
(XEN) Processor #1 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x03] enabled)
(XEN) Processor #3 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x05] enabled)
(XEN) Processor #5 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x07] enabled)
(XEN) Processor #7 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
(XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) PCI: MCFG configuration 0: base a0000000 segment 0 buses 0 - 255
(XEN) PCI: MCFG area at a0000000 reserved in E820
(XEN) amk_mcfg_ioremap: PCI_MCFG_VIRT_START ffff808000000000
(XEN) amk_mcfg_ioremap: start_bus 0 end_bus ff
(XEN) amk_mcfg_ioremap: virt ffff808000000000 mfn = a0000 size ff00000
(XEN) amk_mcfg_ioremap: PCI_MCFG_VIRT_START ffff808000000000
(XEN) amk_mcfg_ioremap: virt  ffff808000000000 size ff00000
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2933.568 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN)  - APIC MMIO access virtualisation
(XEN)  - APIC TPR shadow
(XEN)  - Extended Page Tables (EPT)
(XEN)  - Virtual-Processor Identifiers (VPID)
(XEN)  - Virtual NMI
(XEN)  - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) mce_init: init bank0
(XEN) mce_init: init bank1
(XEN) CPU0: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU0
(XEN) CMCI: CPU0 owner_map[16c], no_cmci_map[93]
(XEN) CPU0: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 1/2 eip 8c000
(XEN) Initializing CPU#1
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) mce_init: init bank1
(XEN) CPU1: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU1
(XEN) CMCI: CPU1 owner_map[2c], no_cmci_map[93]
(XEN) CPU1: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 2/4 eip 8c000
(XEN) Initializing CPU#2
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) mce_init: init bank1
(XEN) CPU2: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU2
(XEN) CMCI: CPU2 owner_map[2c], no_cmci_map[93]
(XEN) CPU2: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 3/6 eip 8c000
(XEN) Initializing CPU#3
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) mce_init: init bank1
(XEN) CPU3: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU3
(XEN) CMCI: CPU3 owner_map[2c], no_cmci_map[93]
(XEN) CPU3: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 4/1 eip 8c000
(XEN) Initializing CPU#4
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) Intel machine check reporting enabled on CPU#4.
(XEN) mce_init: init bank1
(XEN) CPU4: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU4
(XEN) CMCI: CPU4 owner_map[0], no_cmci_map[93]
(XEN) CPU4: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 5/3 eip 8c000
(XEN) Initializing CPU#5
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#5.
(XEN) mce_init: init bank1
(XEN) CPU5: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU5
(XEN) CMCI: CPU5 owner_map[0], no_cmci_map[93]
(XEN) CPU5: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 6/5 eip 8c000
(XEN) Initializing CPU#6
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#6.
(XEN) mce_init: init bank1
(XEN) CPU6: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU6
(XEN) CMCI: CPU6 owner_map[0], no_cmci_map[93]
(XEN) CPU6: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Booting processor 7/7 eip 8c000
(XEN) Initializing CPU#7
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#7.
(XEN) mce_init: init bank1
(XEN) CPU7: Thermal monitoring enabled (TM1)
(XEN) CMCI: find owner on CPU7
(XEN) CMCI: CPU7 owner_map[0], no_cmci_map[93]
(XEN) CPU7: Intel Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
(XEN) Total of 8 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN)  -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 8 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) microcode.c:73:d32767 microcode: CPU7 resumed
(XEN) microcode.c:73:d32767 microcode: CPU5 resumed
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) microcode.c:73:d32767 microcode: CPU6 resumed
(XEN) microcode.c:73:d32767 microcode: CPU4 resumed
(XEN) Brought up 8 CPUs
(XEN) I/O virtualisation disabled
(XEN) CPUIDLE: disabled due to no HPET. Force enable with 'cpuidle'.
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0x1000000 memsz=0x7c9000
(XEN) elf_parse_binary: phdr: paddr=0x17c9000 memsz=0xdab78
(XEN) elf_parse_binary: phdr: paddr=0x18a4000 memsz=0x888
(XEN) elf_parse_binary: phdr: paddr=0x18a6000 memsz=0x75200
(XEN) elf_parse_binary: phdr: paddr=0x191c000 memsz=0x146a0
(XEN) elf_parse_binary: phdr: paddr=0x1931000 memsz=0x132000
(XEN) elf_parse_binary: memory: 0x1000000 -> 0x1a63000
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff818b3200
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81009000
(XEN) elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb"
(XEN) elf_xen_parse_note: PAE_MODE = "yes"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
(XEN) elf_xen_addr_calc_check: addresses:
(XEN)     virt_base        = 0xffffffff80000000
(XEN)     elf_paddr_offset = 0x0
(XEN)     virt_offset      = 0xffffffff80000000
(XEN)     virt_kstart      = 0xffffffff81000000
(XEN)     virt_kend        = 0xffffffff81a63000
(XEN)     virt_entry       = 0xffffffff818b3200
(XEN)     p2m_base         = 0xffffffffffffffff
(XEN)  Xen  kernel: 64-bit, lsb, compat32
(XEN)  Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x1a63000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN)  Dom0 alloc.:   0000000158000000->000000015c000000 (180224 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN)  Loaded kernel: ffffffff81000000->ffffffff81a63000
(XEN)  Init. ramdisk: ffffffff81a63000->ffffffff82491800
(XEN)  Phys-Mach map: ffffffff82492000->ffffffff82612000
(XEN)  Start info:    ffffffff82612000->ffffffff826124b4
(XEN)  Page tables:   ffffffff82613000->ffffffff8262a000
(XEN)  Boot stack:    ffffffff8262a000->ffffffff8262b000
(XEN)  TOTAL:         ffffffff80000000->ffffffff82800000
(XEN)  ENTRY ADDRESS: ffffffff818b3200
(XEN) Dom0 has maximum 1 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff81000000 -> 0xffffffff817c9000
(XEN) elf_load_binary: phdr 1 at 0xffffffff817c9000 -> 0xffffffff818a3b78
(XEN) elf_load_binary: phdr 2 at 0xffffffff818a4000 -> 0xffffffff818a4888
(XEN) elf_load_binary: phdr 3 at 0xffffffff818a6000 -> 0xffffffff8191b200
(XEN) elf_load_binary: phdr 4 at 0xffffffff8191c000 -> 0xffffffff819306a0
(XEN) elf_load_binary: phdr 5 at 0xffffffff81931000 -> 0xffffffff81932000
(XEN) Scrubbing Free RAM: ................................done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 136kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
[    0.000000] PAT disabled on Xen
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.30-rc6-tip (t_patrickco@waitaha) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #5 SMP Fri Jun 26 16:33:19 BST 2009
[    0.000000] Command line: root=/dev/sda1 ro console=hvc0 earlyprintk=xen ignore_loglevel
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  Xen: 0000000000000000 - 000000000009ec00 (usable)
[    0.000000]  Xen: 000000000009ec00 - 0000000000100000 (reserved)
[    0.000000]  Xen: 0000000000100000 - 0000000030000000 (usable)
[    0.000000]  Xen: 000000009cf88000 - 000000009d106000 (ACPI NVS)
[    0.000000]  Xen: 000000009f6bd000 - 000000009f6bf000 (reserved)
[    0.000000]  Xen: 000000009f714000 - 000000009f7bf000 (ACPI NVS)
[    0.000000]  Xen: 000000009f7e1000 - 000000009f7ff000 (ACPI data)
[    0.000000]  Xen: 000000009f800000 - 00000000b0000000 (reserved)
[    0.000000]  Xen: 00000000fc000000 - 00000000fd000000 (reserved)
[    0.000000]  Xen: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] console [xenboot0] enabled
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] DMI 2.5 present.
[    0.000000] last_pfn = 0x30000 max_arch_pfn = 0x400000000
[    0.000000] e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000001000 (usable)
[    0.000000]  modified: 0000000000001000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 000000000009ec00 (usable)
[    0.000000]  modified: 000000000009ec00 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 0000000030000000 (usable)
[    0.000000]  modified: 000000009cf88000 - 000000009d106000 (ACPI NVS)
[    0.000000]  modified: 000000009f6bd000 - 000000009f6bf000 (reserved)
[    0.000000]  modified: 000000009f714000 - 000000009f7bf000 (ACPI NVS)
[    0.000000]  modified: 000000009f7e1000 - 000000009f7ff000 (ACPI data)
[    0.000000]  modified: 000000009f800000 - 00000000b0000000 (reserved)
[    0.000000]  modified: 00000000fc000000 - 00000000fd000000 (reserved)
[    0.000000]  modified: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] init_memory_mapping: 0000000000000000-0000000030000000
[    0.000000]  0000000000 - 0030000000 page 4k
[    0.000000] kernel direct mapping tables up to 30000000 @ 100000-282000
[    0.000000] RAMDISK: 01a63000 - 02491800
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
[    0.000000] ACPI: XSDT 000000009f7fe120 0006C (v01 INTEL  DX58SO   00000493      01000013)
[    0.000000] ACPI: FACP 000000009f7fd000 000F4 (v03 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI Warning (tbfadt-0562): Optional field Pm2ControlBlock has zero address or length: 0000000000000450/0 [20090320]
[    0.000000] ACPI Warning (tbfadt-0612): Invalid length for Pm2ControlBlock: 0, using default 8 [20090320]
[    0.000000] ACPI: DSDT 000000009f7f8000 043A2 (v02 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: FACS 000000009f727000 00040
[    0.000000] ACPI: APIC 000000009f7f7000 00138 (v02 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: WDDT 000000009f7f6000 00040 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: MCFG 000000009f7f5000 0003C (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: ASF! 000000009f7f4000 000AC (v32 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: SSDT 000000009f7e3000 0E134 (v01 INTEL  SSDT  PM 00000493 MSFT 0100000D)
[    0.000000] ACPI: DMAR 000000009f7e1000 00110 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: WDTT 000000009f7f2000 00164 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
[    0.000000] ACPI: ASPT 000000009f7f3000 00034 (v04 INTEL  PerfTune 00000493 MSFT 0100000D)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] (8 early reservations) ==> bootmem [0000000000 - 0030000000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0002613000 - 000262a000]   XEN PAGETABLES ==> [0002613000 - 000262a000]
[    0.000000]   #2 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
[    0.000000]   #3 [0001000000 - 0001a42e08]    TEXT DATA BSS ==> [0001000000 - 0001a42e08]
[    0.000000]   #4 [0001a63000 - 0002491800]          RAMDISK ==> [0001a63000 - 0002491800]
[    0.000000]   #5 [0002492000 - 0002613000]   XEN START INFO ==> [0002492000 - 0002613000]
[    0.000000]   #6 [0001a43000 - 0001a430bc]              BRK ==> [0001a43000 - 0001a430bc]
[    0.000000]   #7 [0000100000 - 0000268000]          PGTABLE ==> [0000100000 - 0000268000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00100000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000001
[    0.000000]     0: 0x00000006 -> 0x0000009e
[    0.000000]     0: 0x00000100 -> 0x00030000
[    0.000000] On node 0 totalpages: 196505
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 363 pages reserved
[    0.000000]   DMA zone: 3574 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 2632 pages used for memmap
[    0.000000]   DMA32 zone: 189880 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
(XEN) io_apic.c:2119: 
(XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
(XEN) ioapic_guest_write: old_entry=000000f0, new_entry=00010000
(XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 30000000:6cf88000)
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Allocated 21 4k pages, static data 83616 bytes
[    1.334542] trying to map vcpu_info 0 at ffffc9000000b060, mfn 15a641, offset 96
[    1.344598] cpu 0 using vcpu_info at ffffc9000000b060
[    1.354698] Xen: using vcpu_info placement
[    1.362787] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 193454
[    1.366820] Kernel command line: root=/dev/sda1 ro console=hvc0 earlyprintk=xen ignore_loglevel
[    1.379391] Initializing CPU#0
[    1.391081] Experimental hierarchical RCU implementation.
[    1.397126] Experimental hierarchical RCU init done.
[    1.405217] NR_IRQS:4352 nr_irqs:256
[    1.411309] xen: registering gsi 0 triggering 1 polarity 0
[    1.417341] xen: --> irq=0
[    1.425419] xen_set_ioapic_routing: irq 0 gsi 0 vector 240 ioapic 0 pin 0 triggering 0 polarity 0
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
(XEN) ioapic_guest_write: old_entry=00010000, new_entry=000000f0
(XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
[    1.429470] xen: registering gsi 1 triggering 1 polarity 0
[    1.469866] xen: --> irq=1
[    1.477946] xen_set_ioapic_routing: irq 1 gsi 1 vector 32 ioapic 0 pin 1 triggering 0 polarity 0
[    1.481989] xen: registering gsi 3 triggering 1 polarity 0
[    1.494109] xen: --> irq=3
[    1.502204] xen_set_ioapic_routing: irq 3 gsi 3 vector 40 ioapic 0 pin 3 triggering 0 polarity 0
[    1.506247] xen: registering gsi 4 triggering 1 polarity 0
[    1.518367] xen: --> irq=4
[    1.526447] xen_set_ioapic_routing: irq 4 gsi 4 vector 48 ioapic 0 pin 4 triggering 0 polarity 0
[    1.530490] xen: registering gsi 5 triggering 1 polarity 0
[    1.542610] xen: --> irq=5
[    1.550691] xen_set_ioapic_routing: irq 5 gsi 5 vector 56 ioapic 0 pin 5 triggering 0 polarity 0
[    1.554733] xen: registering gsi 6 triggering 1 polarity 0
[    1.568874] xen: --> irq=6
[    1.576954] xen_set_ioapic_routing: irq 6 gsi 6 vector 64 ioapic 0 pin 6 triggering 0 polarity 0
[    1.580998] xen: registering gsi 7 triggering 1 polarity 0
[    1.593117] xen: --> irq=7
[    1.601212] xen_set_ioapic_routing: irq 7 gsi 7 vector 72 ioapic 0 pin 7 triggering 0 polarity 0
[    1.605255] xen: registering gsi 8 triggering 1 polarity 0
[    1.617375] xen: --> irq=8
[    1.625455] xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 triggering 0 polarity 0
[    1.629498] xen: registering gsi 9 triggering 0 polarity 0
[    1.641618] xen: --> irq=9
[    1.649698] xen_set_ioapic_routing: irq 9 gsi 9 vector 88 ioapic 0 pin 9 triggering 1 polarity 0
[    1.653741] xen: registering gsi 10 triggering 1 polarity 0
[    1.665861] xen: --> irq=10
[    1.673942] xen_set_ioapic_routing: irq 10 gsi 10 vector 96 ioapic 0 pin 10 triggering 0 polarity 0
[    1.677984] xen: registering gsi 11 triggering 1 polarity 0
[    1.692125] xen: --> irq=11
[    1.700220] xen_set_ioapic_routing: irq 11 gsi 11 vector 104 ioapic 0 pin 11 triggering 0 polarity 0
[    1.704262] xen: registering gsi 12 triggering 1 polarity 0
[    1.716383] xen: --> irq=12
[    1.724463] xen_set_ioapic_routing: irq 12 gsi 12 vector 112 ioapic 0 pin 12 triggering 0 polarity 0
[    1.728506] xen: registering gsi 13 triggering 1 polarity 0
[    1.742646] xen: --> irq=13
[    1.750727] xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin 13 triggering 0 polarity 0
[    1.754769] xen: registering gsi 14 triggering 1 polarity 0
[    1.768910] xen: --> irq=14
[    1.776990] xen_set_ioapic_routing: irq 14 gsi 14 vector 136 ioapic 0 pin 14 triggering 0 polarity 0
[    1.781033] xen: registering gsi 15 triggering 1 polarity 0
[    1.793154] xen: --> irq=15
[    1.801248] xen_set_ioapic_routing: irq 15 gsi 15 vector 144 ioapic 0 pin 15 triggering 0 polarity 0
[    1.805291] PID hash table entries: 4096 (order: 12, 32768 bytes)
[    1.819441] Detected 2933.440 MHz processor.
[    1.834273] Console: colour VGA+ 80x25
[    1.834276] console handover: boot [xenboot0] -> real [hvc0]
[    1.839722] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    1.857999] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    1.865971] Checking aperture...
[    1.883620] No AGP bridge found
[    1.883709] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.891355] xen_swiotlb_fixup: buf=ffff8800034ab000 size=67108864
[    1.909832] xen_swiotlb_fixup: buf=ffff88000750b000 size=32768
[    1.909894] Placing 64MB software IO TLB between ffff8800034ab000 - ffff8800074ab000
[    1.914431] software IO TLB at phys 0x34ab000 - 0x74ab000
[    1.927065] Memory: 682788k/786432k available (5383k kernel code, 412k absent, 102560k reserved, 3284k data, 504k init)
[    1.938701] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    1.950806] Xen: using vcpuop timer interface
[    1.956860] installing Xen timer for CPU 0
[    1.960957]   alloc irq_desc for 24 on node 0
[    1.969030]   alloc kstat_irqs on node 0
[    1.134074] Calibrating delay loop (skipped), value calculated using timer frequency.. 5866.88 BogoMIPS (lpj=2933440)
[    1.150302] Security Framework initialized
[    1.156339] SELinux:  Initializing.
[    1.162407] SELinux:  Starting in permissive mode
[    1.170492] Mount-cache hash table entries: 256
[    1.176656] Initializing cgroup subsys ns
[    1.180594] Initializing cgroup subsys cpuacct
[    1.188679] Initializing cgroup subsys freezer
[    1.196781] CPU: Physical Processor ID: 0
[    1.200806] CPU: Processor Core ID: 0
[    1.206874] CPU: L1 I cache: 32K, L1 D cache: 32K
[    1.214979] CPU: L2 cache: 256K
[    1.219020] CPU: L3 cache: 8192K
[    1.223073] SMP alternatives: switching to UP code
[    1.265593] Freeing SMP alternatives: 41k freed
[    1.265604] ACPI: Core revision 20090320
[    1.281457]   alloc irq_desc for 25 on node 0
[    1.281461]   alloc kstat_irqs on node 0
[    1.281468]   alloc irq_desc for 26 on node 0
[    1.281471]   alloc kstat_irqs on node 0
[    1.281476]   alloc irq_desc for 27 on node 0
[    1.281479]   alloc kstat_irqs on node 0
[    1.281484]   alloc irq_desc for 28 on node 0
[    1.285882]   alloc kstat_irqs on node 0
[    1.292007] Brought up 1 CPUs
[    1.296104] khelper used greatest stack depth: 6264 bytes left
[    1.306222] net_namespace: 1832 bytes
[    1.310356] Booting paravirtualized kernel on Xen
[    1.318247] Xen version: 3.5-unstable (preserve-AD) (dom0)
[    1.324444] Grant table initialized
[    1.330427] Time:  7:29:44  Date: 07/02/09
[    1.336497] NET: Registered protocol family 16
[    1.344720]   alloc irq_desc for 29 on node 0
[    1.350628]   alloc kstat_irqs on node 0
[    1.354722] xenbus_probe_init ok
[    1.360979] ACPI: bus type pci registered
[    1.364919] PCI: MCFG configuration 0: base a0000000 segment 0 buses 0 - 255
[    1.376932] PCI: MCFG area at a0000000 reserved in E820
[    1.423141] PCI: Using MMCONFIG at a0000000 - afffffff
[    1.423145] PCI: Using configuration type 1 for base access
[    1.423420] khelper used greatest stack depth: 6152 bytes left
[    1.430698] bio: create slab <bio-0> at 0
[    1.432241] ACPI: EC: Look up EC in DSDT
[    1.459694] ACPI: Interpreter enabled
[    1.459698] ACPI: (supports S0 S1 S3 S4 S5)
[    1.459729] ACPI: Using IOAPIC for interrupt routing
[    1.467252] ACPI: No dock devices found.
[    1.467265] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    1.467499] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    1.467507] pci 0000:00:01.0: PME# disabled
[    1.467614] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[    1.475988] pci 0000:00:03.0: PME# disabled
[    1.482173] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    1.492186] pci 0000:00:07.0: PME# disabled
[    1.496818] pci 0000:00:1a.0: reg 20 io port: [0x50c0-0x50df]
[    1.506522] pci 0000:00:1a.1: reg 20 io port: [0x50a0-0x50bf]
[    1.514603] pci 0000:00:1a.2: reg 20 io port: [0x5080-0x509f]
[    1.524699] pci 0000:00:1a.7: reg 10 32bit mmio: [0xb7201400-0xb72017ff]
[    1.532746] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    1.542774] pci 0000:00:1a.7: PME# disabled
[    1.546911] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.556948] pci 0000:00:1c.0: PME# disabled
[    1.563108] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    1.573147] pci 0000:00:1c.1: PME# disabled
[    1.577291] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    1.587327] pci 0000:00:1c.4: PME# disabled
[    1.593485] pci 0000:00:1d.0: reg 20 io port: [0x5060-0x507f]
[    1.603647] pci 0000:00:1d.1: reg 20 io port: [0x5040-0x505f]
[    1.611729] pci 0000:00:1d.2: reg 20 io port: [0x5020-0x503f]
[    1.619802] pci 0000:00:1d.7: reg 10 32bit mmio: [0xb7201000-0xb72013ff]
[    1.627850] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    1.637879] pci 0000:00:1d.7: PME# disabled
[    1.644136] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    1.654075] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[    1.664174] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
[    1.672256] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
[    1.684420] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
[    1.696630] pci 0000:00:1f.2: reg 10 io port: [0x5138-0x513f]
[    1.704627] pci 0000:00:1f.2: reg 14 io port: [0x514c-0x514f]
[    1.714728] pci 0000:00:1f.2: reg 18 io port: [0x5130-0x5137]
[    1.722809] pci 0000:00:1f.2: reg 1c io port: [0x5148-0x514b]
[    1.730890] pci 0000:00:1f.2: reg 20 io port: [0x5110-0x511f]
[    1.738971] pci 0000:00:1f.2: reg 24 io port: [0x5100-0x510f]
[    1.747126] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf0000000-0xf00000ff]
[    1.757167] pci 0000:00:1f.3: reg 20 io port: [0x5000-0x501f]
[    1.765305] pci 0000:00:1f.5: reg 10 io port: [0x5128-0x512f]
[    1.775382] pci 0000:00:1f.5: reg 14 io port: [0x5144-0x5147]
[    1.783465] pci 0000:00:1f.5: reg 18 io port: [0x5120-0x5127]
[    1.791546] pci 0000:00:1f.5: reg 1c io port: [0x5140-0x5143]
[    1.799628] pci 0000:00:1f.5: reg 20 io port: [0x50f0-0x50ff]
[    1.807708] pci 0000:00:1f.5: reg 24 io port: [0x50e0-0x50ef]
[    1.817996] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    1.825888] pci 0000:02:00.0: PME# disabled
[    1.829986] pci 0000:00:03.0: bridge io port: [0x3000-0x4fff]
[    1.840065] pci 0000:00:03.0: bridge 32bit mmio: [0xb0000000-0xb6ffffff]
[    1.848148] pci 0000:00:03.0: bridge 64bit mmio pref: [0xd0000000-0xefffffff]
[    1.860340] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    1.870446] pci 0000:03:00.0: PME# disabled
[    1.874563] pci 0000:03:02.0: PME# supported from D0 D3hot D3cold
[    1.884619] pci 0000:03:02.0: PME# disabled
[    1.888721] pci 0000:02:00.0: bridge io port: [0x3000-0x4fff]
[    1.900814] pci 0000:02:00.0: bridge 32bit mmio: [0xb0000000-0xb6ffffff]
[    1.908897] pci 0000:02:00.0: bridge 64bit mmio pref: [0xd0000000-0xefffffff]
[    1.921071] pci 0000:04:00.0: reg 10 32bit mmio: [0xb6000000-0xb6ffffff]
[    1.929137] pci 0000:04:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
[    1.939238] pci 0000:04:00.0: reg 1c 64bit mmio: [0xb4000000-0xb5ffffff]
[    1.949333] pci 0000:04:00.0: reg 24 io port: [0x4000-0x407f]
[    1.957413] pci 0000:04:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
[    1.967671] pci 0000:03:00.0: bridge io port: [0x4000-0x4fff]
[    1.975640] pci 0000:03:00.0: bridge 32bit mmio: [0xb4000000-0xb6ffffff]
[    1.985745] pci 0000:03:00.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
[    1.997920] pci 0000:05:00.0: reg 10 32bit mmio: [0xb2000000-0xb2ffffff]
[    2.005986] pci 0000:05:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
[    2.016087] pci 0000:05:00.0: reg 1c 64bit mmio: [0xb0000000-0xb1ffffff]
[    2.024161] pci 0000:05:00.0: reg 24 io port: [0x3000-0x307f]
[    2.034263] pci 0000:05:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
[    2.044470] pci 0000:03:02.0: bridge io port: [0x3000-0x3fff]
[    2.052441] pci 0000:03:02.0: bridge 32bit mmio: [0xb0000000-0xb2ffffff]
[    2.062545] pci 0000:03:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[    2.072937] pci 0000:08:00.0: reg 10 64bit mmio: [0xb7100000-0xb710ffff]
[    2.082843] pci 0000:08:00.0: PME# supported from D3hot D3cold
[    2.092894] pci 0000:08:00.0: PME# disabled
[    2.097012] pci 0000:00:1c.1: bridge 32bit mmio: [0xb7100000-0xb71fffff]
[    2.107062] pci 0000:09:00.0: reg 10 io port: [0x2018-0x201f]
[    2.117134] pci 0000:09:00.0: reg 14 io port: [0x2024-0x2027]
[    2.125215] pci 0000:09:00.0: reg 18 io port: [0x2010-0x2017]
[    2.133296] pci 0000:09:00.0: reg 1c io port: [0x2020-0x2023]
[    2.141377] pci 0000:09:00.0: reg 20 io port: [0x2000-0x200f]
[    2.149459] pci 0000:09:00.0: reg 24 32bit mmio: [0xb7000000-0xb70003ff]
[    2.159608] pci 0000:09:00.0: supports D1
[    2.165612] pci 0000:09:00.0: PME# supported from D0 D1 D3hot
[    2.173697] pci 0000:09:00.0: PME# disabled
[    2.179835] pci 0000:00:1c.4: bridge io port: [0x2000-0x2fff]
[    2.189902] pci 0000:00:1c.4: bridge 32bit mmio: [0xb7000000-0xb70fffff]
[    2.198028] pci 0000:0a:02.0: reg 10 io port: [0x1000-0x101f]
[    2.208202] pci 0000:00:1e.0: transparent bridge
[    2.214146] pci 0000:00:1e.0: bridge io port: [0x1000-0x1fff]
[    2.222277] pci_bus 0000:00: on NUMA node 0
[    2.228287] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    2.239217] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[    2.246663] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
[    2.256632] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
[    2.264713] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
[    2.274817] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[    2.282899] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[    2.304782] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    2.305184] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    2.315263] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    2.325364] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    2.335467] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    2.349606] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    2.359709] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    2.371829] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    2.382038] xenbus_probe_backend_init bus registered ok
[    2.387974] xenbus_probe_frontend_init bus registered ok
[    2.396011] xen_balloon: Initialising balloon driver.
[    2.404389] SCSI subsystem initialized
[    2.410244] libata version 3.00 loaded.
[    2.414548] usbcore: registered new interface driver usbfs
[    2.422431] usbcore: registered new interface driver hub
[    2.430587] usbcore: registered new device driver usb
[    2.438908] PCI: Using ACPI for IRQ routing
[    2.445116] cfg80211: Using static regulatory domain info
[    2.452784] cfg80211: Regulatory domain: US
[    2.458845] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    2.470967] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[    2.479545] 	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    2.489646] 	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    2.499749] 	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    2.509850] 	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    2.519951] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[    2.530055] NetLabel: Initializing
[    2.536113] NetLabel:  domain hash size = 128
[    2.542174] NetLabel:  protocols = UNLABELED CIPSOv4
[    2.548242] NetLabel:  unlabeled traffic allowed by default
[    2.556387] cfg80211: Calling CRDA for country: US
[    2.564530] Xen: Initializing Xen DMA ops
[    2.570531] Xen: Enabling DMA fallback to swiotlb
[    2.578706] hpet clockevent registered
[    2.582696] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    2.594819] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    2.600881] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    2.613946] pnp: PnP ACPI init
[    2.615063] Switched to high resolution mode on CPU 0
[    2.621132] ACPI: bus type pnp registered
[    2.628158] xen: registering gsi 8 triggering 1 polarity 0
[    2.635257] xen_allocate_pirq: returning irq 8 for gsi 8
[    2.643337] xen: --> irq=8
[    2.647378] xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 triggering 0 polarity 0
[    2.661608] xen: registering gsi 13 triggering 1 polarity 0
[    2.667581] xen_allocate_pirq: returning irq 13 for gsi 13
[    2.675662] xen: --> irq=13
[    2.679703] xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin 13 triggering 0 polarity 0
[    2.695021] pnp: PnP ACPI: found 8 devices
[    2.699927] ACPI: ACPI bus type pnp unregistered
[    2.707993] system 00:05: ioport range 0x500-0x53f has been reserved
[    2.716069] system 00:05: ioport range 0x400-0x47f has been reserved
[    2.726170] system 00:05: ioport range 0x680-0x6ff has been reserved
[    2.739390] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    2.744351] pci 0000:00:01.0:   IO window: disabled
[    2.750416] pci 0000:00:01.0:   MEM window: disabled
[    2.758496] pci 0000:00:01.0:   PREFETCH window: disabled
[    2.764562] pci 0000:04:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]
[    2.776676] pci 0000:03:00.0: PCI bridge, secondary bus 0000:04
[    2.786790] pci 0000:03:00.0:   IO window: 0x4000-0x4fff
[    2.794874] pci 0000:03:00.0:   MEM window: 0xb4000000-0xb6ffffff
[    2.802954] pci 0000:03:00.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
[    2.815079] pci 0000:05:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
[    2.825174] pci 0000:03:02.0: PCI bridge, secondary bus 0000:05
[    2.835276] pci 0000:03:02.0:   IO window: 0x3000-0x3fff
[    2.843360] pci 0000:03:02.0:   MEM window: 0xb0000000-0xb2ffffff
[    2.851440] pci 0000:03:02.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
[    2.863564] pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
[    2.871641] pci 0000:02:00.0:   IO window: 0x3000-0x4fff
[    2.879725] pci 0000:02:00.0:   MEM window: 0xb0000000-0xb6ffffff
[    2.889839] pci 0000:02:00.0:   PREFETCH window: 0x000000d0000000-0x000000efffffff
[    2.899943] pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
[    2.910039] pci 0000:00:03.0:   IO window: 0x3000-0x4fff
[    2.916102] pci 0000:00:03.0:   MEM window: 0xb0000000-0xb6ffffff
[    2.926203] pci 0000:00:03.0:   PREFETCH window: 0x000000d0000000-0x000000efffffff
[    2.936307] pci 0000:00:07.0: PCI bridge, secondary bus 0000:06
[    2.946403] pci 0000:00:07.0:   IO window: disabled
[    2.952468] pci 0000:00:07.0:   MEM window: disabled
[    2.960547] pci 0000:00:07.0:   PREFETCH window: disabled
[    2.966611] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:07
[    2.976706] pci 0000:00:1c.0:   IO window: disabled
[    2.982786] pci 0000:00:1c.0:   MEM window: disabled
[    2.990865] pci 0000:00:1c.0:   PREFETCH window: disabled
[    2.998951] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:08
[    3.009044] pci 0000:00:1c.1:   IO window: disabled
[    3.015111] pci 0000:00:1c.1:   MEM window: 0xb7100000-0xb71fffff
[    3.023190] pci 0000:00:1c.1:   PREFETCH window: disabled
[    3.031275] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:09
[    3.041371] pci 0000:00:1c.4:   IO window: 0x2000-0x2fff
[    3.047434] pci 0000:00:1c.4:   MEM window: 0xb7000000-0xb70fffff
[    3.057534] pci 0000:00:1c.4:   PREFETCH window: disabled
[    3.063598] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
[    3.073695] pci 0000:00:1e.0:   IO window: 0x1000-0x1fff
[    3.081792] pci 0000:00:1e.0:   MEM window: disabled
[    3.089872] pci 0000:00:1e.0:   PREFETCH window: disabled
[    3.095941] xen: registering gsi 16 triggering 0 polarity 1
[    3.104012]   alloc irq_desc for 16 on node 0
[    3.112091]   alloc kstat_irqs on node 0
[    3.116142] xen: --> irq=16
[    3.120173] xen_set_ioapic_routing: irq 16 gsi 16 vector 152 ioapic 0 pin 16 triggering 1 polarity 1
[    3.134318] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.144421] pci 0000:00:01.0: setting latency timer to 64
[    3.152502] xen: registering gsi 16 triggering 0 polarity 1
[    3.160578] xen_allocate_pirq: returning irq 16 for gsi 16
[    3.168658] xen: --> irq=16
[    3.172700] xen_set_ioapic_routing: irq 16 gsi 16 vector 152 ioapic 0 pin 16 triggering 1 polarity 1
[    3.186857] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.194939] pci 0000:00:03.0: setting latency timer to 64
[    3.203025] pci 0000:02:00.0: setting latency timer to 64
[    3.211106] pci 0000:03:00.0: setting latency timer to 64
[    3.219186] pci 0000:03:02.0: setting latency timer to 64
[    3.227265] xen: registering gsi 16 triggering 0 polarity 1
[    3.235341] xen_allocate_pirq: returning irq 16 for gsi 16
[    3.243422] xen: --> irq=16
[    3.247463] xen_set_ioapic_routing: irq 16 gsi 16 vector 152 ioapic 0 pin 16 triggering 1 polarity 1
[    3.261607] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.271710] pci 0000:00:07.0: setting latency timer to 64
[    3.279793] xen: registering gsi 17 triggering 0 polarity 1
[    3.287882]   alloc irq_desc for 17 on node 0
[    3.295963]   alloc kstat_irqs on node 0
[    3.300010] xen: --> irq=17
[    3.304044] xen_set_ioapic_routing: irq 17 gsi 17 vector 160 ioapic 0 pin 17 triggering 1 polarity 1
[    3.318188] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    3.326272] pci 0000:00:1c.0: setting latency timer to 64
[    3.334353] xen: registering gsi 16 triggering 0 polarity 1
[    3.342428] xen_allocate_pirq: returning irq 16 for gsi 16
[    3.350509] xen: --> irq=16
[    3.354550] xen_set_ioapic_routing: irq 16 gsi 16 vector 152 ioapic 0 pin 16 triggering 1 polarity 1
[    3.368694] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    3.378797] pci 0000:00:1c.1: setting latency timer to 64
[    3.386894] xen: registering gsi 17 triggering 0 polarity 1
[    3.394969] xen_allocate_pirq: returning irq 17 for gsi 17
[    3.403050] xen: --> irq=17
[    3.407091] xen_set_ioapic_routing: irq 17 gsi 17 vector 160 ioapic 0 pin 17 triggering 1 polarity 1
[    3.421235] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    3.431338] pci 0000:00:1c.4: setting latency timer to 64
[    3.437402] pci 0000:00:1e.0: setting latency timer to 64
[    3.445479] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    3.453557] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[    3.463659] pci_bus 0000:02: resource 0 io:  [0x3000-0x4fff]
[    3.473760] pci_bus 0000:02: resource 1 mem: [0xb0000000-0xb6ffffff]
[    3.481855] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xefffffff]
[    3.491956] pci_bus 0000:03: resource 0 io:  [0x3000-0x4fff]
[    3.502057] pci_bus 0000:03: resource 1 mem: [0xb0000000-0xb6ffffff]
[    3.509625] pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xefffffff]
[    3.519727] pci_bus 0000:04: resource 0 io:  [0x4000-0x4fff]
[    3.529828] pci_bus 0000:04: resource 1 mem: [0xb4000000-0xb6ffffff]
[    3.537921] pci_bus 0000:04: resource 2 pref mem [0xe0000000-0xefffffff]
[    3.546002] pci_bus 0000:05: resource 0 io:  [0x3000-0x3fff]
[    3.556103] pci_bus 0000:05: resource 1 mem: [0xb0000000-0xb2ffffff]
[    3.564184] pci_bus 0000:05: resource 2 pref mem [0xd0000000-0xdfffffff]
[    3.574287] pci_bus 0000:08: resource 1 mem: [0xb7100000-0xb71fffff]
[    3.584387] pci_bus 0000:09: resource 0 io:  [0x2000-0x2fff]
[    3.592468] pci_bus 0000:09: resource 1 mem: [0xb7000000-0xb70fffff]
[    3.602569] pci_bus 0000:0a: resource 0 io:  [0x1000-0x1fff]
[    3.610650] pci_bus 0000:0a: resource 3 io:  [0x00-0xffff]
[    3.616711] pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffffffffffff]
[    3.626838] NET: Registered protocol family 2
[    3.634959] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[    3.647192] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[    3.657418] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    3.665380] TCP: Hash tables configured (established 131072 bind 65536)
[    3.675313] TCP reno registered
[    3.681432] NET: Registered protocol family 1
[    3.687477] Trying to unpack rootfs image as initramfs...
[    3.699083] Freeing initrd memory: 10426k freed
[    3.702951] kvm: no hardware support
[    3.707688] has_svm: not amd
[    3.711681] kvm: no hardware support
[    3.716653] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    3.727845] Scanning for low memory corruption every 60 seconds
[    3.738268] audit: initializing netlink socket (disabled)
[    3.744043] type=2000 audit(1246519786.260:1): initialized
[    3.762322] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    3.764898] VFS: Disk quotas dquot_6.5.2
[    3.766348] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    3.777238] msgmni has been set to 1556
[    3.782601] SELinux:  Registering netfilter hooks
[    3.790848] alg: No test for stdrng (krng)
[    3.794676] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    3.806679] io scheduler noop registered
[    3.812739] io scheduler anticipatory registered
[    3.820820] io scheduler deadline registered
[    3.826906] io scheduler cfq registered (default)
[    3.832964] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10
[    3.841023] pci 0000:00:1a.0: Performing full reset
[    3.849128] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010
[    3.859205] pci 0000:00:1a.1: Performing full reset
[    3.867309] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010
[    3.875367] pci 0000:00:1a.2: Performing full reset
[    3.883596] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
[    3.891530] pci 0000:00:1d.0: Performing full reset
[    3.899633] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
[    3.909712] pci 0000:00:1d.1: Performing full reset
[    3.915795] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
[    3.925875] pci 0000:00:1d.2: Performing full reset
[    3.934167] pci 0000:05:00.0: Boot video device
[    3.940182] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    3.950350] pcieport-driver 0000:00:03.0: setting latency timer to 64
[    3.958426] pcieport-driver 0000:00:07.0: setting latency timer to 64
[    3.968520] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    3.978621] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[    3.986702] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[    3.996956] aer 0000:00:01.0:pcie02: AER service couldn't init device: no _OSC support
[    4.008712] aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support
[    4.020833] aer 0000:00:07.0:pcie02: AER service couldn't init device: no _OSC support
[    4.030997] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    4.039321] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    4.051146] ACPI: Power Button [PWRF]
[    4.055284] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[    4.067313] ACPI: Sleep Button [SLPB]
[    4.074035] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
[    4.085490]  [20090320]
[    4.087657] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    4.097680] processor ACPI_CPU:00: registered as cooling_device0
[    4.105695] ACPI: Processor [CPU0] (supports 8 throttling states)
[    4.118079] Event-channel device installed.
[    4.119894] ***blkif_init
[    4.125279] *** netif_init
[    4.128427] registering netback
[    4.137246]   alloc irq_desc for 30 on node 0
[    4.140071]   alloc kstat_irqs on node 0
[    4.146700] Non-volatile memory driver v1.3
[    4.152233] Linux agpgart interface v0.103
[    4.158361] [drm] Initialized drm 1.1.0 20060810
[    4.166363] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
(XEN) irq.c:647:d0 Cannot bind IRQ 0 to guest. In use by 'timer'.
(XEN) irq.c:647:d0 Cannot bind IRQ 0 to guest. In use by 'timer'.
(XEN) irq.c:647:d0 Cannot bind IRQ 0 to guest. In use by 'timer'.
(XEN) irq.c:647:d0 Cannot bind IRQ 0 to guest. In use by 'timer'.
[    4.418178] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[    4.418490] xen: registering gsi 18 triggering 0 polarity 1
[    4.418495]   alloc irq_desc for 18 on node 0
[    4.418498]   alloc kstat_irqs on node 0
[    4.418503] xen: --> irq=18
[    4.418506] xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1
[    4.418515] serial 0000:0a:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    4.418734] 0000:0a:02.0: ttyS0 at I/O 0x1008 (irq = 18) is a 16550A
[    4.420421] brd: module loaded
[    4.421421] loop: module loaded
[    4.421518] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    4.421632] Driver 'sd' needs updating - please use bus_type methods
[    4.421670] Driver 'sr' needs updating - please use bus_type methods
[    4.421763] ahci 0000:09:00.0: version 3.0
[    4.421777] xen: registering gsi 16 triggering 0 polarity 1
[    4.421780] xen_allocate_pirq: returning irq 16 for gsi 16
[    4.421783] xen: --> irq=16
[    4.421786] xen_set_ioapic_routing: irq 16 gsi 16 vector 152 ioapic 0 pin 16 triggering 1 polarity 1
[    4.421794] ahci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.421814] ahci 0000:09:00.0: controller can't do NCQ, turning off CAP_NCQ
[    4.421817] ahci 0000:09:00.0: controller can't do PMP, turning off CAP_PMP
[    4.421821] ahci 0000:09:00.0: MV_AHCI HACK: port_map 7 -> 3
[    4.421824] ahci 0000:09:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
[    4.421837] ahci: SSS flag set, parallel bus scan disabled
[    4.421874] ahci 0000:09:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
[    4.427327] ahci 0000:09:00.0: flags: 64bit stag led slum part 
[    4.437433] ahci 0000:09:00.0: setting latency timer to 64
[    4.443666] scsi0 : ahci
[    4.447702] scsi1 : ahci
[    4.451689] scsi2 : ahci
[    4.455729] ata1: SATA max UDMA/133 abar m1024@0xb7000000 port 0xb7000100 irq 16
[    4.467734] ata2: SATA max UDMA/133 abar m1024@0xb7000000 port 0xb7000180 irq 16
[    4.477834] ata3: DUMMY
[    4.786094] ata1: SATA link down (SStatus 0 SControl 300)
[    5.091081] ata2: SATA link down (SStatus 0 SControl 300)
[    5.091182] ata_piix 0000:00:1f.2: version 2.13
[    5.091195] xen: registering gsi 19 triggering 0 polarity 1
[    5.091199]   alloc irq_desc for 19 on node 0
[    5.091202]   alloc kstat_irqs on node 0
[    5.091206] xen: --> irq=19
[    5.091209] xen_set_ioapic_routing: irq 19 gsi 19 vector 176 ioapic 0 pin 19 triggering 1 polarity 1
[    5.091217] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    5.091225] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    5.091265] ata_piix 0000:00:1f.2: setting latency timer to 64
[    5.091327] scsi3 : ata_piix
[    5.091436] scsi4 : ata_piix
[    5.091653] ata4: SATA max UDMA/133 cmd 0x5138 ctl 0x514c bmdma 0x5110 irq 19
[    5.091662] ata5: SATA max UDMA/133 cmd 0x5130 ctl 0x5148 bmdma 0x5118 irq 19
[    5.852135] ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.852157] ata4.01: SATA link down (SStatus 0 SControl 300)
[    5.855318] ata4.00: ATAPI: PIONEER BD-ROM  BDC-202, 1.04, max UDMA/66
[    5.861324] ata4.00: configured for UDMA/66
[    5.874697] scsi 3:0:0:0: CD-ROM            PIONEER  BD-ROM  BDC-202  1.04 PQ: 0 ANSI: 5
[    5.897899] sr0: scsi3-mmc drive: 32x/32x writer dvd-ram cd/rw xa/form2 cdda tray
[    5.897910] Uniform CD-ROM driver Revision: 3.20
[    5.898073] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    5.898169] sr 3:0:0:0: Attached scsi generic sg0 type 5
[    6.659077] ata5.00: SATA link down (SStatus 0 SControl 300)
[    6.659100] ata5.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    6.673659] ata5.01: ATA-8: ST3500320AS, SD15, max UDMA/133
[    6.673667] ata5.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    6.679673] ata5.01: configured for UDMA/133
[    6.679747] scsi 4:0:1:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
[    6.679924] sd 4:0:1:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[    6.679943] sd 4:0:1:0: [sda] Write Protect is off
[    6.679947] sd 4:0:1:0: [sda] Mode Sense: 00 3a 00 00
[    6.679987] sd 4:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.680078]  sda: sda1 sda2 < sda5 >
[    6.705505] sd 4:0:1:0: [sda] Attached SCSI disk
[    6.705601] sd 4:0:1:0: Attached scsi generic sg1 type 0
[    6.705686] xen: registering gsi 18 triggering 0 polarity 1
[    6.705690] xen_allocate_pirq: returning irq 18 for gsi 18
[    6.705693] xen: --> irq=18
[    6.705696] xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1
[    6.705703] ata_piix 0000:00:1f.5: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    6.705712] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[    6.705751] ata_piix 0000:00:1f.5: setting latency timer to 64
[    6.705813] scsi5 : ata_piix
[    6.705924] scsi6 : ata_piix
[    6.706094] ata6: SATA max UDMA/133 cmd 0x5128 ctl 0x5144 bmdma 0x50f0 irq 18
[    6.706102] ata7: SATA max UDMA/133 cmd 0x5120 ctl 0x5140 bmdma 0x50f8 irq 18
[    7.022281] ata6: SATA link down (SStatus 0 SControl 300)
[    7.478013] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    7.481607] ata7.00: ATA-8: ST3500320AS, SD15, max UDMA/133
[    7.481615] ata7.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    7.487621] ata7.00: configured for UDMA/133
[    7.487693] scsi 6:0:0:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
[    7.487863] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[    7.487881] sd 6:0:0:0: [sdb] Write Protect is off
[    7.487885] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    7.487913] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.488013]  sdb:
[    7.510421] sd 6:0:0:0: [sdb] Attached SCSI disk
[    7.510515] sd 6:0:0:0: Attached scsi generic sg2 type 0
[    7.510812] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
[    7.510816] Copyright (c) 1999-2006 Intel Corporation.
[    7.510863] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.4-k4
[    7.510867] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[    7.510964] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    7.510968] e100: Copyright(c) 1999-2006 Intel Corporation
[    7.511020] tg3.c:v3.98 (February 25, 2009)
[    7.511032] xen: registering gsi 17 triggering 0 polarity 1
[    7.511036] xen_allocate_pirq: returning irq 17 for gsi 17
[    7.511039] xen: --> irq=17
[    7.511042] xen_set_ioapic_routing: irq 17 gsi 17 vector 160 ioapic 0 pin 17 triggering 1 polarity 1
[    7.511049] tg3 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    7.511058] tg3 0000:08:00.0: setting latency timer to 64
[    7.513038] tg3 0000:08:00.0: PME# disabled
[    7.519136] eth0: Tigon3 [partno(BCM95721A211F) rev 4201] (PCI Express) MAC address 00:10:18:32:51:a2
[    7.519141] eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[    7.519146] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    7.519149] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    7.519230] sky2 driver version 1.22
[    7.519431] console [netcon0] enabled
[    7.519435] netconsole: network logging started
[    7.519566] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.519571] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
[    7.519591] xen: registering gsi 18 triggering 0 polarity 1
[    7.519594] xen_allocate_pirq: returning irq 18 for gsi 18
[    7.519597] xen: --> irq=18
[    7.519600] xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a0a8, new_entry=0001a0a8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    7.519616] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    7.519631] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    7.519637] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    7.519696] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file 'devices'
[    7.519703] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    7.519765] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    7.519775] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[    7.519781] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
[    7.519811] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.523720] ehci_hcd 0000:00:1a.7: debug port 1
[    7.523729] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    7.523733] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[    7.523740] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xb7201400
[    7.523745] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.527643] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[    7.532928] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    7.532968] usb usb1: default language 0x0409
[    7.532983] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.532990] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.532995] usb usb1: Product: EHCI Host Controller
[    7.532998] usb usb1: Manufacturer: Linux 2.6.30-rc6-tip ehci_hcd
[    7.533001] usb usb1: SerialNumber: 0000:00:1a.7
[    7.533030] usb usb1: uevent
[    7.533073] usb usb1: usb_probe_device
[    7.533077] usb usb1: configuration #1 chosen from 1 choice
[    7.533084] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    7.533099] usb 1-0:1.0: uevent
[    7.533139] hub 1-0:1.0: usb_probe_interface
[    7.533143] hub 1-0:1.0: usb_probe_interface - got id
[    7.533146] hub 1-0:1.0: USB hub found
[    7.533159] hub 1-0:1.0: 6 ports detected
[    7.533162] hub 1-0:1.0: standalone hub
[    7.533165] hub 1-0:1.0: no power switching (usb 1.0)
[    7.533168] hub 1-0:1.0: individual port over-current protection
[    7.533171] hub 1-0:1.0: power on to power good time: 20ms
[    7.533177] hub 1-0:1.0: local power source is good
[    7.533181] hub 1-0:1.0: trying to enable port power on non-switchable hub
[    7.533293] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    7.533366] xen: registering gsi 23 triggering 0 polarity 1
[    7.533371]   alloc irq_desc for 23 on node 0
[    7.533374]   alloc kstat_irqs on node 0
[    7.533378] xen: --> irq=23
[    7.533381] xen_set_ioapic_routing: irq 23 gsi 23 vector 184 ioapic 0 pin 23 triggering 1 polarity 1
[    7.533389] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    7.533403] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    7.533409] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    7.533459] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002'
[    7.533516] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    7.533525] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[    7.533531] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
[    7.533557] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.537460] ehci_hcd 0000:00:1d.7: debug port 1
[    7.537469] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    7.537473] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[    7.537487] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb7201000
[    7.537493] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.541384] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[    7.546901] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    7.546947] usb usb2: default language 0x0409
[    7.546962] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    7.546969] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.546976] usb usb2: Product: EHCI Host Controller
[    7.546984] usb usb2: Manufacturer: Linux 2.6.30-rc6-tip ehci_hcd
[    7.546988] usb usb2: SerialNumber: 0000:00:1d.7
[    7.547016] usb usb2: uevent
[    7.547078] usb usb2: usb_probe_device
[    7.547082] usb usb2: configuration #1 chosen from 1 choice
[    7.547089] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[    7.547103] usb 2-0:1.0: uevent
[    7.547142] hub 2-0:1.0: usb_probe_interface
[    7.547145] hub 2-0:1.0: usb_probe_interface - got id
[    7.547149] hub 2-0:1.0: USB hub found
[    7.547161] hub 2-0:1.0: 6 ports detected
[    7.547164] hub 2-0:1.0: standalone hub
[    7.547167] hub 2-0:1.0: no power switching (usb 1.0)
[    7.547170] hub 2-0:1.0: individual port over-current protection
[    7.547173] hub 2-0:1.0: power on to power good time: 20ms
[    7.547178] hub 2-0:1.0: local power source is good
[    7.547182] hub 2-0:1.0: trying to enable port power on non-switchable hub
[    7.547256] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    7.547356] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.547360] ohci_hcd: block sizes: ed 80 td 96
[    7.547405] uhci_hcd: USB Universal Host Controller Interface driver
[    7.547481] xen: registering gsi 16 triggering 0 polarity 1
[    7.547485] xen_allocate_pirq: returning irq 16 for gsi 16
[    7.549082] xen: --> irq=16
[    7.553124] xen_set_ioapic_routing: irq 16 gsi 16 vector 152 ioapic 0 pin 16 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
(XEN) ioapic_guest_write: old_entry=0000a098, new_entry=0001a098
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    7.567276] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    7.607676] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    7.615754] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    7.621871] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '003'
[    7.638052] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
[    7.644080] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    7.656180] uhci_hcd 0000:00:1a.0: detected 2 ports
[    7.664247] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[    7.672320] uhci_hcd 0000:00:1a.0: Performing full reset
[    7.680421] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[    7.690505] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000050c0
[    7.698629] usb usb3: default language 0x0409
[    7.704654] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    7.714746] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.726908] usb usb3: Product: UHCI Host Controller
[    7.732969] usb usb3: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
[    7.741050] usb usb3: SerialNumber: 0000:00:1a.0
[    7.749162] usb usb3: uevent
[    7.753190] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
[    7.763285] hub 2-0:1.0: port 1: status 0501 change 0001
[    7.771365] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
[    7.783482] hub 2-0:1.0: port 2: status 0501 change 0001
[    7.791608] usb usb3: usb_probe_device
[    7.797619] usb usb3: configuration #1 chosen from 1 choice
[    7.805711] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[    7.815816] usb 3-0:1.0: uevent
[    7.819884] hub 3-0:1.0: usb_probe_interface
[    7.825902] hub 3-0:1.0: usb_probe_interface - got id
[    7.831963] hub 3-0:1.0: USB hub found
[    7.838047] hub 3-0:1.0: 2 ports detected
[    7.844085] hub 3-0:1.0: standalone hub
[    7.850145] hub 3-0:1.0: no power switching (usb 1.0)
[    7.858227] hub 3-0:1.0: individual port over-current protection
[    7.866309] hub 3-0:1.0: power on to power good time: 2ms
[    7.874397] hub 3-0:1.0: local power source is good
[    7.882471] hub 3-0:1.0: trying to enable port power on non-switchable hub
[    7.890617] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    7.906758] hub 2-0:1.0: state 7 ports 6 chg 0006 evt 0000
[    7.914811] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[    7.924905] ehci_hcd 0000:00:1d.7: port 1 low speed --> companion
[    7.933056] xen: registering gsi 21 triggering 0 polarity 1
[    7.941060]   alloc irq_desc for 21 on node 0
[    7.949139]   alloc kstat_irqs on node 0
[    7.953190] xen: --> irq=21
[    7.957221] xen_set_ioapic_routing: irq 21 gsi 21 vector 192 ioapic 0 pin 21 triggering 1 polarity 1
[    7.971378] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    7.981481] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    7.991579] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    7.997692] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
[    8.009789] hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[    8.019868] ehci_hcd 0000:00:1d.7: port 2 low speed --> companion
[    8.027971] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '004'
[    8.044185] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    8.054221] uhci_hcd 0000:00:1a.1: detected 2 ports
[    8.062295] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[    8.070381] uhci_hcd 0000:00:1a.1: Performing full reset
[    8.078482] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[    8.088600] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000050a0
[    8.096721] usb usb4: default language 0x0409
[    8.102744] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    8.110815] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.122937] usb usb4: Product: UHCI Host Controller
[    8.131018] usb usb4: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
[    8.139099] usb usb4: SerialNumber: 0000:00:1a.1
[    8.147225] usb usb4: uevent
[    8.151265] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
[    8.161349] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0004
[    8.169412] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.177503] usb usb4: usb_probe_device
[    8.183546] usb usb4: configuration #1 chosen from 1 choice
[    8.191640] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[    8.201743] usb 4-0:1.0: uevent
[    8.205811] hub 4-0:1.0: usb_probe_interface
[    8.211830] hub 4-0:1.0: usb_probe_interface - got id
[    8.219910] hub 4-0:1.0: USB hub found
[    8.223970] hub 4-0:1.0: 2 ports detected
[    8.230012] hub 4-0:1.0: standalone hub
[    8.236073] hub 4-0:1.0: no power switching (usb 1.0)
[    8.244154] hub 4-0:1.0: individual port over-current protection
[    8.252235] hub 4-0:1.0: power on to power good time: 2ms
[    8.260323] hub 4-0:1.0: local power source is good
[    8.268398] hub 4-0:1.0: trying to enable port power on non-switchable hub
[    8.276545] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    8.292738] xen: registering gsi 19 triggering 0 polarity 1
[    8.300722] xen_allocate_pirq: returning irq 19 for gsi 19
[    8.308803] xen: --> irq=19
[    8.312844] xen_set_ioapic_routing: irq 19 gsi 19 vector 176 ioapic 0 pin 19 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
(XEN) ioapic_guest_write: old_entry=0000a0b0, new_entry=0001a0b0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    8.326996] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    8.367408] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    8.375485] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    8.381619] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.389646] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '005'
[    8.405881] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    8.417924] uhci_hcd 0000:00:1a.2: detected 2 ports
[    8.423978] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
[    8.434072] uhci_hcd 0000:00:1a.2: Performing full reset
[    8.442173] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
[    8.450236] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00005080
[    8.460382] usb usb5: default language 0x0409
[    8.466419] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    8.474490] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.486612] usb usb5: Product: UHCI Host Controller
[    8.492673] usb usb5: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
[    8.502774] usb usb5: SerialNumber: 0000:00:1a.2
[    8.508864] usb usb5: uevent
[    8.514943] usb usb5: usb_probe_device
[    8.518937] usb usb5: configuration #1 chosen from 1 choice
[    8.525014] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[    8.535115] usb 5-0:1.0: uevent
[    8.541204] hub 5-0:1.0: usb_probe_interface
[    8.547220] hub 5-0:1.0: usb_probe_interface - got id
[    8.553282] hub 5-0:1.0: USB hub found
[    8.559363] hub 5-0:1.0: 2 ports detected
[    8.565417] hub 5-0:1.0: standalone hub
[    8.569457] hub 5-0:1.0: no power switching (usb 1.0)
[    8.577538] hub 5-0:1.0: individual port over-current protection
[    8.587640] hub 5-0:1.0: power on to power good time: 2ms
[    8.593708] hub 5-0:1.0: local power source is good
[    8.601782] hub 5-0:1.0: trying to enable port power on non-switchable hub
[    8.611948] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    8.628140] xen: registering gsi 23 triggering 0 polarity 1
[    8.634109] xen_allocate_pirq: returning irq 23 for gsi 23
[    8.642189] xen: --> irq=23
[    8.646230] xen_set_ioapic_routing: irq 23 gsi 23 vector 184 ioapic 0 pin 23 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
(XEN) ioapic_guest_write: old_entry=0000a0b8, new_entry=0001a0b8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    8.662403] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    8.700794] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    8.710892] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    8.717059] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.725053] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '006'
[    8.741260] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    8.751310] uhci_hcd 0000:00:1d.0: detected 2 ports
[    8.759384] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[    8.767471] uhci_hcd 0000:00:1d.0: Performing full reset
[    8.775612] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[    8.785696] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00005060
[    8.793818] usb usb6: default language 0x0409
[    8.799844] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    8.809937] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.820038] usb usb6: Product: UHCI Host Controller
[    8.828119] usb usb6: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
[    8.836200] usb usb6: SerialNumber: 0000:00:1d.0
[    8.844313] usb usb6: uevent
[    8.848367] usb usb6: usb_probe_device
[    8.852363] usb usb6: configuration #1 chosen from 1 choice
[    8.860460] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[    8.870561] usb 6-0:1.0: uevent
[    8.874629] hub 6-0:1.0: usb_probe_interface
[    8.882667] hub 6-0:1.0: usb_probe_interface - got id
[    8.888727] hub 6-0:1.0: USB hub found
[    8.892789] hub 6-0:1.0: 2 ports detected
[    8.898829] hub 6-0:1.0: standalone hub
[    8.904889] hub 6-0:1.0: no power switching (usb 1.0)
[    8.912971] hub 6-0:1.0: individual port over-current protection
[    8.923072] hub 6-0:1.0: power on to power good time: 2ms
[    8.929172] hub 6-0:1.0: local power source is good
[    8.937214] hub 6-0:1.0: trying to enable port power on non-switchable hub
[    8.945361] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    8.961549] xen: registering gsi 19 triggering 0 polarity 1
[    8.969551] xen_allocate_pirq: returning irq 19 for gsi 19
[    8.977632] xen: --> irq=19
[    8.981673] xen_set_ioapic_routing: irq 19 gsi 19 vector 176 ioapic 0 pin 19 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
(XEN) ioapic_guest_write: old_entry=0000a0b0, new_entry=0001a0b0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    8.995825] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    9.036247] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    9.044324] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    9.050447] uhci_hcd 0000:00:1d.0: port 1 portsc 01ab,00
[    9.058479] hub 6-0:1.0: port 1: status 0301 change 0003
[    9.066564] uhci_hcd 0000:00:1d.0: port 2 portsc 01ab,00
[    9.074633] hub 6-0:1.0: port 2: status 0301 change 0003
[    9.082729] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '007'
[    9.098941] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    9.108987] uhci_hcd 0000:00:1d.1: detected 2 ports
[    9.117061] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[    9.125134] uhci_hcd 0000:00:1d.1: Performing full reset
[    9.133235] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[    9.143319] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00005040
[    9.151434] usb usb3: suspend_rh (auto-stop)
[    9.157526] usb usb7: default language 0x0409
[    9.165561] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    9.173632] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    9.185753] usb usb7: Product: UHCI Host Controller
[    9.191814] usb usb7: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
[    9.199895] usb usb7: SerialNumber: 0000:00:1d.1
[    9.208008] usb usb7: uevent
[    9.212062] hub 6-0:1.0: state 7 ports 2 chg 0006 evt 0000
[    9.218107] hub 6-0:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
[    9.228202] usb usb7: usb_probe_device
[    9.234240] usb usb7: configuration #1 chosen from 1 choice
[    9.242334] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[    9.252437] usb 7-0:1.0: uevent
[    9.256506] hub 7-0:1.0: usb_probe_interface
[    9.262524] hub 7-0:1.0: usb_probe_interface - got id
[    9.268598] hub 7-0:1.0: USB hub found
[    9.274677] hub 7-0:1.0: 2 ports detected
[    9.280719] hub 7-0:1.0: standalone hub
[    9.286780] hub 7-0:1.0: no power switching (usb 1.0)
[    9.294861] hub 7-0:1.0: individual port over-current protection
[    9.302943] hub 7-0:1.0: power on to power good time: 2ms
[    9.311033] hub 7-0:1.0: local power source is good
[    9.319105] hub 7-0:1.0: trying to enable port power on non-switchable hub
[    9.327282] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    9.343440] xen: registering gsi 18 triggering 0 polarity 1
[    9.351430] xen_allocate_pirq: returning irq 18 for gsi 18
[    9.359510] xen: --> irq=18
[    9.363552] xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a0a8, new_entry=0001a0a8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    9.377717] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    9.418117] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    9.426195] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    9.432276] usb usb4: suspend_rh (auto-stop)
[    9.440431] usb 6-1: new low speed USB device using uhci_hcd and address 2
[    9.448459] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '008'
[    9.464656] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    9.476740] uhci_hcd 0000:00:1d.2: detected 2 ports
[    9.482790] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[    9.492875] uhci_hcd 0000:00:1d.2: Performing full reset
[    9.500983] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[    9.509040] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005020
[    9.519186] usb usb8: default language 0x0409
[    9.525210] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    9.533281] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    9.545402] usb usb8: Product: UHCI Host Controller
[    9.551463] usb usb8: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
[    9.561564] usb usb8: SerialNumber: 0000:00:1d.2
[    9.567671] usb usb8: uevent
[    9.573756] usb usb8: usb_probe_device
[    9.577741] usb usb8: configuration #1 chosen from 1 choice
[    9.583819] usb usb8: adding 8-0:1.0 (config #1, interface 0)
[    9.593918] usb 8-0:1.0: uevent
[    9.600007] hub 8-0:1.0: usb_probe_interface
[    9.606025] hub 8-0:1.0: usb_probe_interface - got id
[    9.612086] hub 8-0:1.0: USB hub found
[    9.618168] hub 8-0:1.0: 2 ports detected
[    9.624208] hub 8-0:1.0: standalone hub
[    9.628248] hub 8-0:1.0: no power switching (usb 1.0)
[    9.636329] hub 8-0:1.0: individual port over-current protection
[    9.646431] hub 8-0:1.0: power on to power good time: 2ms
[    9.652508] usb usb5: suspend_rh (auto-stop)
[    9.660632] hub 8-0:1.0: local power source is good
[    9.666647] hub 8-0:1.0: trying to enable port power on non-switchable hub
[    9.676828] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
[    9.693076] usbcore: registered new interface driver usblp
[    9.701009] Initializing USB Mass Storage driver...
[    9.709138] usbcore: registered new interface driver usb-storage
[    9.717155] USB Mass Storage support registered.
[    9.723290] usbcore: registered new interface driver libusual
[    9.733480] PNP: No PS/2 controller found. Probing ports directly.
[    9.744350] serio: i8042 KBD port at 0x60,0x64 irq 1
[    9.749485] serio: i8042 AUX port at 0x60,0x64 irq 12
[    9.755737] mice: PS/2 mouse device common for all mice
[    9.764002] rtc_cmos 00:02: RTC can wake from S4
[    9.771867] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    9.779896] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    9.787945] usb 6-1: skipped 1 descriptor after interface
[    9.796091] xen: registering gsi 18 triggering 0 polarity 1
[    9.804082] xen_allocate_pirq: returning irq 18 for gsi 18
[    9.812162] xen: --> irq=18
[    9.816203] xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1
(XEN) io_apic.c:2132: 
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a0a8, new_entry=0001a0a8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
[    9.830355] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    9.871039] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    9.884950] usb 6-1: default language 0x0409
[    9.891186] cpuidle: using governor ladder
[    9.895313] cpuidle: using governor menu
[    9.902083] usbcore: registered new interface driver hiddev
[    9.909330] usbcore: registered new interface driver usbhid
[    9.917219] usbhid: v2.6:USB HID core driver
[    9.925463] Advanced Linux Sound Architecture Driver Version 1.0.20.
[    9.933440] usb 6-1: New USB device found, idVendor=045e, idProduct=0083
[    9.943482] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    9.955603] usb 6-1: Product: Basic Optical Mouse
[    9.961664] usb 6-1: Manufacturer: Microsoft
[    9.967799] usb 6-1: uevent
[    9.969946] usb 6-1: usb_probe_device
[    9.975820] usb 6-1: configuration #1 chosen from 1 choice
modprobe: FATAL: Could not load /lib/modules/2.6.30-rc6-tip/modules.dep: No such file or directory
[    9.998089] usb 6-1: adding 6-1:1.0 (config #1, interface 0)
[   10.006169] usb 6-1:1.0: uevent
[   10.012248] usbhid 6-1:1.0: usb_probe_interface
[   10.018248] usbhid 6-1:1.0: usb_probe_interface - got id

[   10.026492] modprobe used greatest stack depth: 5904 bytes left
[   10.034607] ALSA device list:
[   10.040471]   No soundcards found.
[   10.044557] Netfilter messages via NETLINK v0.30.
[   10.050595] nf_conntrack version 0.5.0 (6144 buckets, 24576 max)
[   10.060994] input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input3
[   10.074995] generic-usb 0003:045E:0083.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.0-1/input0
[   10.095102] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002'
[   10.109254] hub 6-0:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
[   10.117394] ctnetlink v0.93: registering with nfnetlink.
[   10.125683] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.133436] TCP cubic registered
[   10.139475] Initializing XFRM netlink socket
[   10.145711] hub 1-0:1.0: hub_suspend
[   10.149592] usb usb1: bus auto-suspend
[   10.155638] ehci_hcd 0000:00:1a.7: suspend root hub
[   10.161907] NET: Registered protocol family 10
[   10.170468] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.175898] IPv6 over IPv4 tunneling driver
[   10.182305] NET: Registered protocol family 17
[   10.190142] RPC: Registered udp transport module.
[   10.198081] RPC: Registered tcp transport module.
[   10.204529] IO APIC resources couldn't be allocated.
[   10.210359] PM: Resume from disk failed.
[   10.216271] registered taskstats version 1
[   10.222441]   Magic number: 1:820:469
[   10.228482] usb 6-2: new low speed USB device using uhci_hcd and address 3
[   10.238559] Freeing unused kernel memory: 504k freed
[   10.246631] Write protecting the kernel read-only data: 7936k
Loading, please wait...
Couldnt get a file descriptor referring to the console
[   10.341084] console_setup used greatest stack depth: 5584 bytes left
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
[   10.393919] usb usb7: suspend_rh (auto-stop)
[   10.393958] usb 6-2: skipped 1 descriptor after interface
[   10.393963] usb 6-2: skipped 1 descriptor after interface
[   10.393967] usb 6-2: New USB device found, idVendor=0566, idProduct=3002
[   10.393971] usb 6-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0


[-- Attachment #4: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Re: Xen cannot boot with pvops dom0

[Jeremy Fitzhardinge]

On 07/01/09 00:32, Patrick Colp wrote:
> Hmmm, OK. Well, something is still going wrong. I find that adding
> things like irqpoll and/or acpi=noirq seems to help a bit. By that I
> mean that it gets further into the boot process before stalling. If I
> wait a while and press random keys/buttons (like Num Lock or the power
> button), then that seems to coax it into booting a little bit more,
> but I've never managed to get it to completely boot. The furthest I
> got was to where it tries to read the root filesystem.
>
> I could give you a dump of the boot-up messages, but aside from the
> ioapic stuff, there's nothing out of the ordinary.

Yeah, from those logs it looks OK.  Was that a "coaxed" Xen boot?  It
certainly looks like lots of interrupts are being received properly
(drives detected, usb probed, etc).

Also, for a more direct comparison, what happens when you boot native
with pci=nomsi?  I assume it will work, but it will make the logs
directly comparable; or maybe the system just doesn't work without MSI?

> Write protecting the kernel read-only data: 7936k
> Loading, please wait...
> Couldnt get a file descriptor referring to the console
Is your initrd set up right?

    J

Re: Xen cannot boot with pvops dom0

[Patrick Colp]

[-- Attachment #1: Type: text/plain, Size: 1893 bytes --]

Here's the boot log for a normal boot with pci=nomsi.

The initrd should be setup properly. I built the kernel using the latest 
unstable and the normal linux make commands (make linux-2.6-pvops 
config|build|install), which should do the right thing.

The Xen boot was an uncoaxed boot. It usually gets up to the point of loading 
Alsa (but this message doesn't manage to get printed to the serial console, just 
to the screen attached to my test box). After that, it's a matter of waiting and 
pushing keys/buttons to try to get it to keep going. It seems to have issues 
trying to read the harddrives as well.


Patrick


Jeremy Fitzhardinge wrote:
> On 07/01/09 00:32, Patrick Colp wrote:
>> Hmmm, OK. Well, something is still going wrong. I find that adding
>> things like irqpoll and/or acpi=noirq seems to help a bit. By that I
>> mean that it gets further into the boot process before stalling. If I
>> wait a while and press random keys/buttons (like Num Lock or the power
>> button), then that seems to coax it into booting a little bit more,
>> but I've never managed to get it to completely boot. The furthest I
>> got was to where it tries to read the root filesystem.
>>
>> I could give you a dump of the boot-up messages, but aside from the
>> ioapic stuff, there's nothing out of the ordinary.
> 
> Yeah, from those logs it looks OK.  Was that a "coaxed" Xen boot?  It
> certainly looks like lots of interrupts are being received properly
> (drives detected, usb probed, etc).
> 
> Also, for a more direct comparison, what happens when you boot native
> with pci=nomsi?  I assume it will work, but it will make the logs
> directly comparable; or maybe the system just doesn't work without MSI?
> 
>> Write protecting the kernel read-only data: 7936k
>> Loading, please wait...
>> Couldnt get a file descriptor referring to the console
> Is your initrd set up right?
> 
>     J

[-- Attachment #2: normal-boot-nomsi.log --]
[-- Type: text/x-log, Size: 114865 bytes --]

Jul  3 08:46:40 zumbi kernel: Inspecting /boot/System.map-2.6.30-rc6-tip
Jul  3 08:46:40 zumbi kernel: Cannot find map file.
Jul  3 08:46:40 zumbi kernel: Loaded 52141 symbols from 1 module.
Jul  3 08:46:40 zumbi kernel: [    0.000000] Initializing cgroup subsys cpuset
Jul  3 08:46:40 zumbi kernel: [    0.000000] Initializing cgroup subsys cpu
Jul  3 08:46:40 zumbi kernel: [    0.000000] Linux version 2.6.30-rc6-tip (t_patrickco@waitaha) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #5 SMP Fri Jun 26 16:33:19 BST 2009
Jul  3 08:46:40 zumbi kernel: [    0.000000] Command line: root=/dev/sda1 ro console=ttyS0 console=tty0 console=hvc0 pci=nomsi
Jul  3 08:46:40 zumbi kernel: [    0.000000] KERNEL supported cpus:
Jul  3 08:46:40 zumbi kernel: [    0.000000]   Intel GenuineIntel
Jul  3 08:46:40 zumbi kernel: [    0.000000]   AMD AuthenticAMD
Jul  3 08:46:40 zumbi kernel: [    0.000000]   Centaur CentaurHauls
Jul  3 08:46:40 zumbi kernel: [    0.000000] BIOS-provided physical RAM map:
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 0000000000100000 - 000000009cf88000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009cf88000 - 000000009d106000 (ACPI NVS)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009d106000 - 000000009f6bd000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f6bd000 - 000000009f6bf000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f6bf000 - 000000009f714000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f714000 - 000000009f7bf000 (ACPI NVS)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f7bf000 - 000000009f7e1000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f7e1000 - 000000009f7ff000 (ACPI data)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f7ff000 - 000000009f800000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 000000009f800000 - 00000000b0000000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 00000000fc000000 - 00000000fd000000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  BIOS-e820: 0000000100000000 - 0000000160000000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000] DMI 2.5 present.
Jul  3 08:46:40 zumbi kernel: [    0.000000] last_pfn = 0x160000 max_arch_pfn = 0x400000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] MTRR default type: uncachable
Jul  3 08:46:40 zumbi kernel: [    0.000000] MTRR fixed ranges enabled:
Jul  3 08:46:40 zumbi kernel: [    0.000000]   00000-9FFFF write-back
Jul  3 08:46:40 zumbi kernel: [    0.000000]   A0000-BFFFF uncachable
Jul  3 08:46:40 zumbi kernel: [    0.000000]   C0000-DFFFF write-protect
Jul  3 08:46:40 zumbi kernel: [    0.000000]   E0000-FFFFF uncachable
Jul  3 08:46:40 zumbi kernel: [    0.000000] MTRR variable ranges enabled:
Jul  3 08:46:40 zumbi kernel: [    0.000000]   0 base 000000000 mask F80000000 write-back
Jul  3 08:46:40 zumbi kernel: [    0.000000]   1 base 080000000 mask FE0000000 write-back
Jul  3 08:46:40 zumbi kernel: [    0.000000]   2 base 100000000 mask F00000000 write-back
Jul  3 08:46:40 zumbi kernel: [    0.000000]   3 disabled
Jul  3 08:46:40 zumbi kernel: [    0.000000]   4 disabled
Jul  3 08:46:40 zumbi kernel: [    0.000000]   5 disabled
Jul  3 08:46:40 zumbi kernel: [    0.000000]   6 disabled
Jul  3 08:46:40 zumbi kernel: [    0.000000]   7 disabled
Jul  3 08:46:40 zumbi kernel: [    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [    0.000000] e820 update range: 00000000a0000000 - 0000000100000000 (usable) ==> (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000] last_pfn = 0x9f800 max_arch_pfn = 0x400000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000] Scanning 1 areas for low memory corruption
Jul  3 08:46:40 zumbi kernel: [    0.000000] modified physical RAM map:
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 0000000000000000 - 0000000000001000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 0000000000001000 - 0000000000006000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 0000000000006000 - 000000000009ec00 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000000009ec00 - 00000000000a0000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 00000000000e0000 - 0000000000100000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 0000000000100000 - 000000009cf88000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009cf88000 - 000000009d106000 (ACPI NVS)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009d106000 - 000000009f6bd000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f6bd000 - 000000009f6bf000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f6bf000 - 000000009f714000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f714000 - 000000009f7bf000 (ACPI NVS)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f7bf000 - 000000009f7e1000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f7e1000 - 000000009f7ff000 (ACPI data)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f7ff000 - 000000009f800000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 000000009f800000 - 00000000b0000000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 00000000fc000000 - 00000000fd000000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 00000000ffe00000 - 0000000100000000 (reserved)
Jul  3 08:46:40 zumbi kernel: [    0.000000]  modified: 0000000100000000 - 0000000160000000 (usable)
Jul  3 08:46:40 zumbi kernel: [    0.000000] initial memory mapped : 0 - 20000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] init_memory_mapping: 0000000000000000-000000009f800000
Jul  3 08:46:40 zumbi kernel: [    0.000000]  0000000000 - 009f800000 page 2M
Jul  3 08:46:40 zumbi kernel: [    0.000000] kernel direct mapping tables up to 9f800000 @ 8000-c000
Jul  3 08:46:40 zumbi kernel: [    0.000000] init_memory_mapping: 0000000100000000-0000000160000000
Jul  3 08:46:40 zumbi kernel: [    0.000000]  0100000000 - 0160000000 page 2M
Jul  3 08:46:40 zumbi kernel: [    0.000000] kernel direct mapping tables up to 160000000 @ a000-11000
Jul  3 08:46:40 zumbi kernel: [    0.000000] RAMDISK: 37c85000 - 37fef7b4
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: XSDT 000000009f7fe120 0006C (v01 INTEL  DX58SO   00000493      01000013)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: FACP 000000009f7fd000 000F4 (v03 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI Warning (tbfadt-0562): Optional field Pm2ControlBlock has zero address or length: 0000000000000450/0 [20090320]
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI Warning (tbfadt-0612): Invalid length for Pm2ControlBlock: 0, using default 8 [20090320]
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: DSDT 000000009f7f8000 043A2 (v02 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: FACS 000000009f727000 00040
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: APIC 000000009f7f7000 00138 (v02 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: WDDT 000000009f7f6000 00040 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: MCFG 000000009f7f5000 0003C (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: ASF! 000000009f7f4000 000AC (v32 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: SSDT 000000009f7e3000 0E134 (v01 INTEL  SSDT  PM 00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: DMAR 000000009f7e1000 00110 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: WDTT 000000009f7f2000 00164 (v01 INTEL  DX58SO   00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: ASPT 000000009f7f3000 00034 (v04 INTEL  PerfTune 00000493 MSFT 0100000D)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: Local APIC address 0xfee00000
Jul  3 08:46:40 zumbi kernel: [    0.000000] (8 early reservations) ==> bootmem [0000000000 - 0160000000]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #2 [0001000000 - 0001a42e08]    TEXT DATA BSS ==> [0001000000 - 0001a42e08]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #3 [0037c85000 - 0037fef7b4]          RAMDISK ==> [0037c85000 - 0037fef7b4]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #4 [000009ec00 - 0000100000]    BIOS reserved ==> [000009ec00 - 0000100000]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #5 [0001a43000 - 0001a430bc]              BRK ==> [0001a43000 - 0001a430bc]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #6 [0000008000 - 000000a000]          PGTABLE ==> [0000008000 - 000000a000]
Jul  3 08:46:40 zumbi kernel: [    0.000000]   #7 [000000a000 - 000000c000]          PGTABLE ==> [000000a000 - 000000c000]
Jul  3 08:46:40 zumbi kernel: [    0.000000] Zone PFN ranges:
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA      0x00000000 -> 0x00001000
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA32    0x00001000 -> 0x00100000
Jul  3 08:46:40 zumbi kernel: [    0.000000]   Normal   0x00100000 -> 0x00160000
Jul  3 08:46:40 zumbi kernel: [    0.000000] Movable zone start PFN for each node
Jul  3 08:46:40 zumbi kernel: [    0.000000] early_node_map[8] active PFN ranges
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x00000000 -> 0x00000001
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x00000006 -> 0x0000009e
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x00000100 -> 0x0009cf88
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x0009d106 -> 0x0009f6bd
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x0009f6bf -> 0x0009f714
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x0009f7bf -> 0x0009f7e1
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x0009f7ff -> 0x0009f800
Jul  3 08:46:40 zumbi kernel: [    0.000000]     0: 0x00100000 -> 0x00160000
Jul  3 08:46:40 zumbi kernel: [    0.000000] On node 0 totalpages: 1045840
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA zone: 56 pages used for memmap
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA zone: 104 pages reserved
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA zone: 3833 pages, LIFO batch:0
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA32 zone: 14280 pages used for memmap
Jul  3 08:46:40 zumbi kernel: [    0.000000]   DMA32 zone: 634351 pages, LIFO batch:31
Jul  3 08:46:40 zumbi kernel: [    0.000000]   Normal zone: 5376 pages used for memmap
Jul  3 08:46:40 zumbi kernel: [    0.000000]   Normal zone: 387840 pages, LIFO batch:31
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: PM-Timer IO Port: 0x408
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: Local APIC address 0xfee00000
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x01] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x03] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x05] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x07] enabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
Jul  3 08:46:40 zumbi kernel: [    0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: IRQ0 used by override.
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: IRQ2 used by override.
Jul  3 08:46:40 zumbi kernel: [    0.000000] ACPI: IRQ9 used by override.
Jul  3 08:46:40 zumbi kernel: [    0.000000] Using ACPI (MADT) for SMP configuration information
Jul  3 08:46:40 zumbi kernel: [    0.000000] 16 Processors exceeds NR_CPUS limit of 8
Jul  3 08:46:40 zumbi kernel: [    0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
Jul  3 08:46:40 zumbi kernel: [    0.000000] nr_irqs_gsi: 24
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009cf88000 - 000000009d106000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f6bd000 - 000000009f6bf000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f714000 - 000000009f7bf000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f7e1000 - 000000009f7ff000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 000000009f800000 - 00000000b0000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000b0000000 - 00000000fc000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fd000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000fd000000 - 00000000ffe00000
Jul  3 08:46:40 zumbi kernel: [    0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
Jul  3 08:46:40 zumbi kernel: [    0.000000] Allocating PCI resources starting at b0000000 (gap: b0000000:4c000000)
Jul  3 08:46:40 zumbi kernel: [    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
Jul  3 08:46:40 zumbi kernel: [    0.000000] PERCPU: Embedded 28 pages at ffff880028028000, static data 83616 bytes
Jul  3 08:46:40 zumbi kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1026024
Jul  3 08:46:40 zumbi kernel: [    0.000000] Kernel command line: root=/dev/sda1 ro console=ttyS0 console=tty0 console=hvc0 pci=nomsi
Jul  3 08:46:40 zumbi kernel: [    0.000000] Initializing CPU#0
Jul  3 08:46:40 zumbi kernel: [    0.000000] Experimental hierarchical RCU implementation.
Jul  3 08:46:40 zumbi kernel: [    0.000000] Experimental hierarchical RCU init done.
Jul  3 08:46:40 zumbi kernel: [    0.000000] NR_IRQS:4352 nr_irqs:472
Jul  3 08:46:40 zumbi kernel: [    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
Jul  3 08:46:40 zumbi kernel: [    0.000000] Extended CMOS year: 2000
Jul  3 08:46:40 zumbi kernel: [    0.000000] Fast TSC calibration using PIT
Jul  3 08:46:40 zumbi kernel: [    0.000000] Detected 2933.044 MHz processor.
Jul  3 08:46:40 zumbi kernel: [   30.031649] Console: colour VGA+ 80x25
Jul  3 08:46:40 zumbi kernel: [   30.031650] console [tty0] enabled
Jul  3 08:46:40 zumbi kernel: [   30.075641] console [ttyS0] enabled
Jul  3 08:46:40 zumbi kernel: [   30.167219] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Jul  3 08:46:40 zumbi kernel: [   30.168687] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Jul  3 08:46:40 zumbi kernel: [   30.169694] Checking aperture...
Jul  3 08:46:40 zumbi kernel: [   30.175748] No AGP bridge found
Jul  3 08:46:40 zumbi kernel: [   30.176166] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Jul  3 08:46:40 zumbi kernel: [   30.181817] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
Jul  3 08:46:40 zumbi kernel: [   30.187914] software IO TLB at phys 0x20000000 - 0x24000000
Jul  3 08:46:40 zumbi kernel: [   30.212752] Memory: 4037788k/5767168k available (5383k kernel code, 1583808k absent, 144664k reserved, 3284k data, 504k init)
Jul  3 08:46:40 zumbi kernel: [   30.213684] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Jul  3 08:46:40 zumbi kernel: [   30.214488] Calibrating delay loop (skipped), value calculated using timer frequency.. 5866.08 BogoMIPS (lpj=2933044)
Jul  3 08:46:40 zumbi kernel: [   30.215431] Security Framework initialized
Jul  3 08:46:40 zumbi kernel: [   30.215860] SELinux:  Initializing.
Jul  3 08:46:40 zumbi kernel: [   30.216261] SELinux:  Starting in permissive mode
Jul  3 08:46:40 zumbi kernel: [   30.216266] Mount-cache hash table entries: 256
Jul  3 08:46:40 zumbi kernel: [   30.216794] Initializing cgroup subsys ns
Jul  3 08:46:40 zumbi kernel: [   30.217213] Initializing cgroup subsys cpuacct
Jul  3 08:46:40 zumbi kernel: [   30.217655] Initializing cgroup subsys freezer
Jul  3 08:46:40 zumbi kernel: [   30.218098] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.218521] CPU: Processor Core ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.218926] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.219414] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.219805] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.220192] [ds] using Core i7 configuration
Jul  3 08:46:40 zumbi kernel: [   30.220625] [ds] sizes: address: 64 bit, bts/pebs record: 24/176 bytes
Jul  3 08:46:40 zumbi kernel: [   30.221191] using mwait in idle threads.
Jul  3 08:46:40 zumbi kernel: [   30.221612] Intel Performance Monitoring support detected.
Jul  3 08:46:40 zumbi kernel: [   30.222084] ... version:         3
Jul  3 08:46:40 zumbi kernel: [   30.222482] ... bit width:       48
Jul  3 08:46:40 zumbi kernel: [   30.222880] ... num counters:    4
Jul  3 08:46:40 zumbi kernel: [   30.223274] ... value mask:      0000ffffffffffff
Jul  3 08:46:40 zumbi kernel: [   30.223722] ... max period:      000000007fffffff
Jul  3 08:46:40 zumbi kernel: [   30.224165] ... fixed counters:  3
Jul  3 08:46:40 zumbi kernel: [   30.224564] ... counter mask:    000000070000000f
Jul  3 08:46:40 zumbi kernel: [   30.225672] ACPI: Core revision 20090320
Jul  3 08:46:40 zumbi kernel: [   30.238163] Setting APIC routing to flat
Jul  3 08:46:40 zumbi kernel: [   30.255128] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
Jul  3 08:46:40 zumbi kernel: [   30.265692] CPU0: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.367485] Booting processor 1 APIC 0x2 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.378421] Initializing CPU#1
Jul  3 08:46:40 zumbi kernel: [   30.438384] Calibrating delay using timer specific routine.. 5865.06 BogoMIPS (lpj=2932531)
Jul  3 08:46:40 zumbi kernel: [   30.438390] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.438391] CPU: Processor Core ID: 1
Jul  3 08:46:40 zumbi kernel: [   30.438393] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.438394] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.438395] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.438989] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.439594] CPU1: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.444504] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.445114] Booting processor 2 APIC 0x4 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.455935] Initializing CPU#2
Jul  3 08:46:40 zumbi kernel: [   30.516342] Calibrating delay using timer specific routine.. 5865.06 BogoMIPS (lpj=2932530)
Jul  3 08:46:40 zumbi kernel: [   30.516348] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.516349] CPU: Processor Core ID: 2
Jul  3 08:46:40 zumbi kernel: [   30.516351] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.516352] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.516352] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.516949] x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.517516] CPU2: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.522434] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.523041] Booting processor 3 APIC 0x6 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.533861] Initializing CPU#3
Jul  3 08:46:40 zumbi kernel: [   30.594300] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  3 08:46:40 zumbi kernel: [   30.594306] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.594307] CPU: Processor Core ID: 3
Jul  3 08:46:40 zumbi kernel: [   30.594309] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.594310] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.594310] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.594905] x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.595442] CPU3: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.600358] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.600970] Booting processor 4 APIC 0x1 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.611791] Initializing CPU#4
Jul  3 08:46:40 zumbi kernel: [   30.672258] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  3 08:46:40 zumbi kernel: [   30.672265] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.672266] CPU: Processor Core ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.672268] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.672269] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.672271] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.673008] x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.673839] CPU4: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.678754] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.679369] Booting processor 5 APIC 0x3 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.690188] Initializing CPU#5
Jul  3 08:46:40 zumbi kernel: [   30.750216] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  3 08:46:40 zumbi kernel: [   30.750221] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.750222] CPU: Processor Core ID: 1
Jul  3 08:46:40 zumbi kernel: [   30.750224] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.750225] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.750226] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.751014] x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.751871] CPU5: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.756784] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.757397] Booting processor 6 APIC 0x5 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.768216] Initializing CPU#6
Jul  3 08:46:40 zumbi kernel: [   30.828174] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932529)
Jul  3 08:46:40 zumbi kernel: [   30.828179] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.828180] CPU: Processor Core ID: 2
Jul  3 08:46:40 zumbi kernel: [   30.828182] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.828183] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.828184] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.828967] x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.829800] CPU6: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.834713] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.835324] Booting processor 7 APIC 0x7 ip 0x6000
Jul  3 08:46:40 zumbi kernel: [   30.846142] Initializing CPU#7
Jul  3 08:46:40 zumbi kernel: [   30.906131] Calibrating delay using timer specific routine.. 5865.05 BogoMIPS (lpj=2932528)
Jul  3 08:46:40 zumbi kernel: [   30.906137] CPU: Physical Processor ID: 0
Jul  3 08:46:40 zumbi kernel: [   30.906138] CPU: Processor Core ID: 3
Jul  3 08:46:40 zumbi kernel: [   30.906140] CPU: L1 I cache: 32K, L1 D cache: 32K
Jul  3 08:46:40 zumbi kernel: [   30.906141] CPU: L2 cache: 256K
Jul  3 08:46:40 zumbi kernel: [   30.906141] CPU: L3 cache: 8192K
Jul  3 08:46:40 zumbi kernel: [   30.906926] x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106
Jul  3 08:46:40 zumbi kernel: [   30.907725] CPU7: Genuine Intel(R) CPU           @ 0000 @ 2.93GHz stepping 02
Jul  3 08:46:40 zumbi kernel: [   30.912637] Skipping synchronization checks as TSC is reliable.
Jul  3 08:46:40 zumbi kernel: [   30.913206] Brought up 8 CPUs
Jul  3 08:46:40 zumbi kernel: [   30.913621] Total of 8 processors activated (46921.49 BogoMIPS).
Jul  3 08:46:40 zumbi kernel: [   30.914418] khelper used greatest stack depth: 6024 bytes left
Jul  3 08:46:40 zumbi kernel: [   30.914483] net_namespace: 1832 bytes
Jul  3 08:46:40 zumbi kernel: [   30.915438] Booting paravirtualized kernel on bare hardware
Jul  3 08:46:40 zumbi kernel: [   30.916082] Time:  7:46:23  Date: 07/03/09
Jul  3 08:46:40 zumbi kernel: [   30.916584] NET: Registered protocol family 16
Jul  3 08:46:40 zumbi kernel: [   30.917161] err -19 in xenbus_probe_init
Jul  3 08:46:40 zumbi kernel: [   30.917739] ACPI: bus type pci registered
Jul  3 08:46:40 zumbi kernel: [   30.918283] PCI: MCFG configuration 0: base a0000000 segment 0 buses 0 - 255
Jul  3 08:46:40 zumbi kernel: [   30.918900] PCI: MCFG area at a0000000 reserved in E820
Jul  3 08:46:40 zumbi kernel: [   30.926745] PCI: Using MMCONFIG at a0000000 - afffffff
Jul  3 08:46:40 zumbi kernel: [   30.927268] PCI: Using configuration type 1 for base access
Jul  3 08:46:40 zumbi kernel: [   30.931356] bio: create slab <bio-0> at 0
Jul  3 08:46:40 zumbi kernel: [   30.932506] ACPI: EC: Look up EC in DSDT
Jul  3 08:46:40 zumbi kernel: [   30.948406] ACPI: Interpreter enabled
Jul  3 08:46:40 zumbi kernel: [   30.948856] ACPI: (supports S0 S1 S3 S4 S5)
Jul  3 08:46:40 zumbi kernel: [   30.949587] ACPI: Using IOAPIC for interrupt routing
Jul  3 08:46:40 zumbi kernel: [   30.954565] ACPI: No dock devices found.
Jul  3 08:46:40 zumbi kernel: [   30.955035] ACPI: PCI Root Bridge [PCI0] (0000:00)
Jul  3 08:46:40 zumbi kernel: [   30.955646] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.956219] pci 0000:00:01.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.956736] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.957307] pci 0000:00:03.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.957824] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.958396] pci 0000:00:07.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.959120] pci 0000:00:1a.0: reg 20 io port: [0x50c0-0x50df]
Jul  3 08:46:40 zumbi kernel: [   30.959181] pci 0000:00:1a.1: reg 20 io port: [0x50a0-0x50bf]
Jul  3 08:46:40 zumbi kernel: [   30.959241] pci 0000:00:1a.2: reg 20 io port: [0x5080-0x509f]
Jul  3 08:46:40 zumbi kernel: [   30.959300] pci 0000:00:1a.7: reg 10 32bit mmio: [0xb7201400-0xb72017ff]
Jul  3 08:46:40 zumbi kernel: [   30.959344] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.959914] pci 0000:00:1a.7: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.960439] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.961009] pci 0000:00:1c.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.961535] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.962106] pci 0000:00:1c.1: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.967954] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.968526] pci 0000:00:1c.4: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.969046] pci 0000:00:1d.0: reg 20 io port: [0x5060-0x507f]
Jul  3 08:46:40 zumbi kernel: [   30.969107] pci 0000:00:1d.1: reg 20 io port: [0x5040-0x505f]
Jul  3 08:46:40 zumbi kernel: [   30.969168] pci 0000:00:1d.2: reg 20 io port: [0x5020-0x503f]
Jul  3 08:46:40 zumbi kernel: [   30.969226] pci 0000:00:1d.7: reg 10 32bit mmio: [0xb7201000-0xb72013ff]
Jul  3 08:46:40 zumbi kernel: [   30.969270] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.969842] pci 0000:00:1d.7: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.970422] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
Jul  3 08:46:40 zumbi kernel: [   30.970427] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
Jul  3 08:46:40 zumbi kernel: [   30.971297] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
Jul  3 08:46:40 zumbi kernel: [   30.971906] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
Jul  3 08:46:40 zumbi kernel: [   30.972770] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
Jul  3 08:46:40 zumbi kernel: [   30.973680] pci 0000:00:1f.2: reg 10 io port: [0x5138-0x513f]
Jul  3 08:46:40 zumbi kernel: [   30.973684] pci 0000:00:1f.2: reg 14 io port: [0x514c-0x514f]
Jul  3 08:46:40 zumbi kernel: [   30.973689] pci 0000:00:1f.2: reg 18 io port: [0x5130-0x5137]
Jul  3 08:46:40 zumbi kernel: [   30.973693] pci 0000:00:1f.2: reg 1c io port: [0x5148-0x514b]
Jul  3 08:46:40 zumbi kernel: [   30.973698] pci 0000:00:1f.2: reg 20 io port: [0x5110-0x511f]
Jul  3 08:46:40 zumbi kernel: [   30.973703] pci 0000:00:1f.2: reg 24 io port: [0x5100-0x510f]
Jul  3 08:46:40 zumbi kernel: [   30.973742] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf0000000-0xf00000ff]
Jul  3 08:46:40 zumbi kernel: [   30.973754] pci 0000:00:1f.3: reg 20 io port: [0x5000-0x501f]
Jul  3 08:46:40 zumbi kernel: [   30.973791] pci 0000:00:1f.5: reg 10 io port: [0x5128-0x512f]
Jul  3 08:46:40 zumbi kernel: [   30.973795] pci 0000:00:1f.5: reg 14 io port: [0x5144-0x5147]
Jul  3 08:46:40 zumbi kernel: [   30.973800] pci 0000:00:1f.5: reg 18 io port: [0x5120-0x5127]
Jul  3 08:46:40 zumbi kernel: [   30.973805] pci 0000:00:1f.5: reg 1c io port: [0x5140-0x5143]
Jul  3 08:46:40 zumbi kernel: [   30.973809] pci 0000:00:1f.5: reg 20 io port: [0x50f0-0x50ff]
Jul  3 08:46:40 zumbi kernel: [   30.973814] pci 0000:00:1f.5: reg 24 io port: [0x50e0-0x50ef]
Jul  3 08:46:40 zumbi kernel: [   30.973897] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.974469] pci 0000:02:00.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.974963] pci 0000:00:03.0: bridge io port: [0x3000-0x4fff]
Jul  3 08:46:40 zumbi kernel: [   30.974966] pci 0000:00:03.0: bridge 32bit mmio: [0xb0000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.974970] pci 0000:00:03.0: bridge 64bit mmio pref: [0xd0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   30.975005] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.975575] pci 0000:03:00.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.976086] pci 0000:03:02.0: PME# supported from D0 D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.976657] pci 0000:03:02.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.977159] pci 0000:02:00.0: bridge io port: [0x3000-0x4fff]
Jul  3 08:46:40 zumbi kernel: [   30.977161] pci 0000:02:00.0: bridge 32bit mmio: [0xb0000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977166] pci 0000:02:00.0: bridge 64bit mmio pref: [0xd0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977196] pci 0000:04:00.0: reg 10 32bit mmio: [0xb6000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977206] pci 0000:04:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977215] pci 0000:04:00.0: reg 1c 64bit mmio: [0xb4000000-0xb5ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977220] pci 0000:04:00.0: reg 24 io port: [0x4000-0x407f]
Jul  3 08:46:40 zumbi kernel: [   30.977225] pci 0000:04:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977279] pci 0000:03:00.0: bridge io port: [0x4000-0x4fff]
Jul  3 08:46:40 zumbi kernel: [   30.977282] pci 0000:03:00.0: bridge 32bit mmio: [0xb4000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977286] pci 0000:03:00.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977317] pci 0000:05:00.0: reg 10 32bit mmio: [0xb2000000-0xb2ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977327] pci 0000:05:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977336] pci 0000:05:00.0: reg 1c 64bit mmio: [0xb0000000-0xb1ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977341] pci 0000:05:00.0: reg 24 io port: [0x3000-0x307f]
Jul  3 08:46:40 zumbi kernel: [   30.977347] pci 0000:05:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977401] pci 0000:03:02.0: bridge io port: [0x3000-0x3fff]
Jul  3 08:46:40 zumbi kernel: [   30.977404] pci 0000:03:02.0: bridge 32bit mmio: [0xb0000000-0xb2ffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977408] pci 0000:03:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
Jul  3 08:46:40 zumbi kernel: [   30.977575] pci 0000:08:00.0: reg 10 64bit mmio: [0xb7100000-0xb710ffff]
Jul  3 08:46:40 zumbi kernel: [   30.977641] pci 0000:08:00.0: PME# supported from D3hot D3cold
Jul  3 08:46:40 zumbi kernel: [   30.978247] pci 0000:08:00.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.978808] pci 0000:00:1c.1: bridge 32bit mmio: [0xb7100000-0xb71fffff]
Jul  3 08:46:40 zumbi kernel: [   30.978853] pci 0000:09:00.0: reg 10 io port: [0x2018-0x201f]
Jul  3 08:46:40 zumbi kernel: [   30.978860] pci 0000:09:00.0: reg 14 io port: [0x2024-0x2027]
Jul  3 08:46:40 zumbi kernel: [   30.978867] pci 0000:09:00.0: reg 18 io port: [0x2010-0x2017]
Jul  3 08:46:40 zumbi kernel: [   30.978873] pci 0000:09:00.0: reg 1c io port: [0x2020-0x2023]
Jul  3 08:46:40 zumbi kernel: [   30.978880] pci 0000:09:00.0: reg 20 io port: [0x2000-0x200f]
Jul  3 08:46:40 zumbi kernel: [   30.978887] pci 0000:09:00.0: reg 24 32bit mmio: [0xb7000000-0xb70003ff]
Jul  3 08:46:40 zumbi kernel: [   30.978924] pci 0000:09:00.0: supports D1
Jul  3 08:46:40 zumbi kernel: [   30.978926] pci 0000:09:00.0: PME# supported from D0 D1 D3hot
Jul  3 08:46:40 zumbi kernel: [   30.979482] pci 0000:09:00.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   30.979996] pci 0000:00:1c.4: bridge io port: [0x2000-0x2fff]
Jul  3 08:46:40 zumbi kernel: [   30.979999] pci 0000:00:1c.4: bridge 32bit mmio: [0xb7000000-0xb70fffff]
Jul  3 08:46:40 zumbi kernel: [   30.980025] pci 0000:0a:02.0: reg 10 io port: [0x1000-0x101f]
Jul  3 08:46:40 zumbi kernel: [   30.980093] pci 0000:00:1e.0: transparent bridge
Jul  3 08:46:40 zumbi kernel: [   30.980590] pci 0000:00:1e.0: bridge io port: [0x1000-0x1fff]
Jul  3 08:46:40 zumbi kernel: [   30.980617] pci_bus 0000:00: on NUMA node 0
Jul  3 08:46:40 zumbi kernel: [   30.980621] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.981100] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.981234] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.981293] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.981351] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.981410] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.981471] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
Jul  3 08:46:40 zumbi kernel: [   30.987330] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Jul  3 08:46:40 zumbi kernel: [   30.988898] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Jul  3 08:46:40 zumbi kernel: [   30.990464] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Jul  3 08:46:40 zumbi kernel: [   30.992030] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Jul  3 08:46:40 zumbi kernel: [   30.993598] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
Jul  3 08:46:40 zumbi kernel: [   30.995313] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Jul  3 08:46:40 zumbi kernel: [   30.996876] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
Jul  3 08:46:40 zumbi kernel: [   30.998597] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Jul  3 08:46:40 zumbi kernel: [   31.000162] xenbus_probe_backend_init bus registered ok
Jul  3 08:46:40 zumbi kernel: [   31.000709] xenbus_probe_frontend_init bus registered ok
Jul  3 08:46:40 zumbi kernel: [   31.001348] SCSI subsystem initialized
Jul  3 08:46:40 zumbi kernel: [   31.001880] libata version 3.00 loaded.
Jul  3 08:46:40 zumbi kernel: [   31.002014] usbcore: registered new interface driver usbfs
Jul  3 08:46:40 zumbi kernel: [   31.002577] usbcore: registered new interface driver hub
Jul  3 08:46:40 zumbi kernel: [   31.003136] usbcore: registered new device driver usb
Jul  3 08:46:40 zumbi kernel: [   31.003785] PCI: Using ACPI for IRQ routing
Jul  3 08:46:40 zumbi kernel: [   31.022122] cfg80211: Using static regulatory domain info
Jul  3 08:46:40 zumbi kernel: [   31.022663] cfg80211: Regulatory domain: US
Jul  3 08:46:40 zumbi kernel: [   31.023139] ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul  3 08:46:40 zumbi kernel: [   31.023985] ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
Jul  3 08:46:40 zumbi kernel: [   31.024589] ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  3 08:46:40 zumbi kernel: [   31.025194] ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  3 08:46:40 zumbi kernel: [   31.025798] ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  3 08:46:40 zumbi kernel: [   31.026402] ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Jul  3 08:46:40 zumbi kernel: [   31.027005] ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
Jul  3 08:46:40 zumbi kernel: [   31.027609] NetLabel: Initializing
Jul  3 08:46:40 zumbi kernel: [   31.028044] NetLabel:  domain hash size = 128
Jul  3 08:46:40 zumbi kernel: [   31.028528] NetLabel:  protocols = UNLABELED CIPSOv4
Jul  3 08:46:40 zumbi kernel: [   31.029045] NetLabel:  unlabeled traffic allowed by default
Jul  3 08:46:40 zumbi kernel: [   31.029597] cfg80211: Calling CRDA for country: US
Jul  3 08:46:40 zumbi kernel: [   31.030238] hpet clockevent registered
Jul  3 08:46:40 zumbi kernel: [   31.030241] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
Jul  3 08:46:40 zumbi kernel: [   31.030861] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
Jul  3 08:46:40 zumbi kernel: [   31.031626] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
Jul  3 08:46:40 zumbi kernel: [   31.040076] Switched to high resolution mode on CPU 0
Jul  3 08:46:40 zumbi kernel: [   31.040200] Switched to high resolution mode on CPU 3
Jul  3 08:46:40 zumbi kernel: [   31.040202] Switched to high resolution mode on CPU 1
Jul  3 08:46:40 zumbi kernel: [   31.040205] Switched to high resolution mode on CPU 2
Jul  3 08:46:40 zumbi kernel: [   31.040569] Switched to high resolution mode on CPU 4
Jul  3 08:46:40 zumbi kernel: [   31.040629] Switched to high resolution mode on CPU 6
Jul  3 08:46:40 zumbi kernel: [   31.040633] Switched to high resolution mode on CPU 7
Jul  3 08:46:40 zumbi kernel: [   31.040659] Switched to high resolution mode on CPU 5
Jul  3 08:46:40 zumbi kernel: [   31.044079] pnp: PnP ACPI init
Jul  3 08:46:40 zumbi kernel: [   31.044508] ACPI: bus type pnp registered
Jul  3 08:46:40 zumbi kernel: [   31.046501] pnp: PnP ACPI: found 8 devices
Jul  3 08:46:40 zumbi kernel: [   31.046971] ACPI: ACPI bus type pnp unregistered
Jul  3 08:46:40 zumbi kernel: [   31.047476] system 00:05: ioport range 0x500-0x53f has been reserved
Jul  3 08:46:40 zumbi kernel: [   31.048057] system 00:05: ioport range 0x400-0x47f has been reserved
Jul  3 08:46:40 zumbi kernel: [   31.048642] system 00:05: ioport range 0x680-0x6ff has been reserved
Jul  3 08:46:40 zumbi kernel: [   31.054066] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
Jul  3 08:46:40 zumbi kernel: [   31.054629] pci 0000:00:01.0:   IO window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.055141] pci 0000:00:01.0:   MEM window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.055655] pci 0000:00:01.0:   PREFETCH window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.056194] pci 0000:04:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   31.057080] pci 0000:03:00.0: PCI bridge, secondary bus 0000:04
Jul  3 08:46:40 zumbi kernel: [   31.057640] pci 0000:03:00.0:   IO window: 0x4000-0x4fff
Jul  3 08:46:40 zumbi kernel: [   31.058173] pci 0000:03:00.0:   MEM window: 0xb4000000-0xb6ffffff
Jul  3 08:46:40 zumbi kernel: [   31.058742] pci 0000:03:00.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
Jul  3 08:46:40 zumbi kernel: [   31.059609] pci 0000:05:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
Jul  3 08:46:40 zumbi kernel: [   31.060497] pci 0000:03:02.0: PCI bridge, secondary bus 0000:05
Jul  3 08:46:40 zumbi kernel: [   31.061058] pci 0000:03:02.0:   IO window: 0x3000-0x3fff
Jul  3 08:46:40 zumbi kernel: [   31.061591] pci 0000:03:02.0:   MEM window: 0xb0000000-0xb2ffffff
Jul  3 08:46:40 zumbi kernel: [   31.062161] pci 0000:03:02.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
Jul  3 08:46:40 zumbi kernel: [   31.063024] pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
Jul  3 08:46:40 zumbi kernel: [   31.063584] pci 0000:02:00.0:   IO window: 0x3000-0x4fff
Jul  3 08:46:40 zumbi kernel: [   31.064118] pci 0000:02:00.0:   MEM window: 0xb0000000-0xb6ffffff
Jul  3 08:46:40 zumbi kernel: [   31.064687] pci 0000:02:00.0:   PREFETCH window: 0x000000d0000000-0x000000efffffff
Jul  3 08:46:40 zumbi kernel: [   31.065553] pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
Jul  3 08:46:40 zumbi kernel: [   31.066116] pci 0000:00:03.0:   IO window: 0x3000-0x4fff
Jul  3 08:46:40 zumbi kernel: [   31.066648] pci 0000:00:03.0:   MEM window: 0xb0000000-0xb6ffffff
Jul  3 08:46:40 zumbi kernel: [   31.067219] pci 0000:00:03.0:   PREFETCH window: 0x000000d0000000-0x000000efffffff
Jul  3 08:46:40 zumbi kernel: [   31.068086] pci 0000:00:07.0: PCI bridge, secondary bus 0000:06
Jul  3 08:46:40 zumbi kernel: [   31.068647] pci 0000:00:07.0:   IO window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.069157] pci 0000:00:07.0:   MEM window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.069672] pci 0000:00:07.0:   PREFETCH window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.070211] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:07
Jul  3 08:46:40 zumbi kernel: [   31.070771] pci 0000:00:1c.0:   IO window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.071282] pci 0000:00:1c.0:   MEM window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.071798] pci 0000:00:1c.0:   PREFETCH window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.072337] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:08
Jul  3 08:46:40 zumbi kernel: [   31.072896] pci 0000:00:1c.1:   IO window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.073409] pci 0000:00:1c.1:   MEM window: 0xb7100000-0xb71fffff
Jul  3 08:46:40 zumbi kernel: [   31.073980] pci 0000:00:1c.1:   PREFETCH window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.074518] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:09
Jul  3 08:46:40 zumbi kernel: [   31.075080] pci 0000:00:1c.4:   IO window: 0x2000-0x2fff
Jul  3 08:46:40 zumbi kernel: [   31.075612] pci 0000:00:1c.4:   MEM window: 0xb7000000-0xb70fffff
Jul  3 08:46:40 zumbi kernel: [   31.076183] pci 0000:00:1c.4:   PREFETCH window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.076722] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
Jul  3 08:46:40 zumbi kernel: [   31.077285] pci 0000:00:1e.0:   IO window: 0x1000-0x1fff
Jul  3 08:46:40 zumbi kernel: [   31.077818] pci 0000:00:1e.0:   MEM window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.078335] pci 0000:00:1e.0:   PREFETCH window: disabled
Jul  3 08:46:40 zumbi kernel: [   31.078876]   alloc irq_desc for 16 on node -1
Jul  3 08:46:40 zumbi kernel: [   31.078877]   alloc kstat_irqs on node -1
Jul  3 08:46:40 zumbi kernel: [   31.078881] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  3 08:46:40 zumbi kernel: [   31.079483] pci 0000:00:01.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.079488] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  3 08:46:40 zumbi kernel: [   31.080089] pci 0000:00:03.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.080094] pci 0000:02:00.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.080099] pci 0000:03:00.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.080103] pci 0000:03:02.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.080107] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  3 08:46:40 zumbi kernel: [   31.080708] pci 0000:00:07.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.080712]   alloc irq_desc for 17 on node -1
Jul  3 08:46:40 zumbi kernel: [   31.080713]   alloc kstat_irqs on node -1
Jul  3 08:46:40 zumbi kernel: [   31.080716] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jul  3 08:46:40 zumbi kernel: [   31.081320] pci 0000:00:1c.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.081324] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
Jul  3 08:46:40 zumbi kernel: [   31.081924] pci 0000:00:1c.1: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.081929] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jul  3 08:46:40 zumbi kernel: [   31.082530] pci 0000:00:1c.4: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.082534] pci 0000:00:1e.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.082537] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
Jul  3 08:46:40 zumbi kernel: [   31.082539] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082540] pci_bus 0000:02: resource 0 io:  [0x3000-0x4fff]
Jul  3 08:46:40 zumbi kernel: [   31.082542] pci_bus 0000:02: resource 1 mem: [0xb0000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082544] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082545] pci_bus 0000:03: resource 0 io:  [0x3000-0x4fff]
Jul  3 08:46:40 zumbi kernel: [   31.082547] pci_bus 0000:03: resource 1 mem: [0xb0000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082548] pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082550] pci_bus 0000:04: resource 0 io:  [0x4000-0x4fff]
Jul  3 08:46:40 zumbi kernel: [   31.082552] pci_bus 0000:04: resource 1 mem: [0xb4000000-0xb6ffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082553] pci_bus 0000:04: resource 2 pref mem [0xe0000000-0xefffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082555] pci_bus 0000:05: resource 0 io:  [0x3000-0x3fff]
Jul  3 08:46:40 zumbi kernel: [   31.082556] pci_bus 0000:05: resource 1 mem: [0xb0000000-0xb2ffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082558] pci_bus 0000:05: resource 2 pref mem [0xd0000000-0xdfffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082560] pci_bus 0000:08: resource 1 mem: [0xb7100000-0xb71fffff]
Jul  3 08:46:40 zumbi kernel: [   31.082561] pci_bus 0000:09: resource 0 io:  [0x2000-0x2fff]
Jul  3 08:46:40 zumbi kernel: [   31.082563] pci_bus 0000:09: resource 1 mem: [0xb7000000-0xb70fffff]
Jul  3 08:46:40 zumbi kernel: [   31.082564] pci_bus 0000:0a: resource 0 io:  [0x1000-0x1fff]
Jul  3 08:46:40 zumbi kernel: [   31.082566] pci_bus 0000:0a: resource 3 io:  [0x00-0xffff]
Jul  3 08:46:40 zumbi kernel: [   31.082567] pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffffffffffff]
Jul  3 08:46:40 zumbi kernel: [   31.082585] NET: Registered protocol family 2
Jul  3 08:46:40 zumbi kernel: [   31.096108] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Jul  3 08:46:40 zumbi kernel: [   31.097179] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
Jul  3 08:46:40 zumbi kernel: [   31.098621] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Jul  3 08:46:40 zumbi kernel: [   31.099365] TCP: Hash tables configured (established 262144 bind 65536)
Jul  3 08:46:40 zumbi kernel: [   31.099960] TCP reno registered
Jul  3 08:46:40 zumbi kernel: [   31.104150] NET: Registered protocol family 1
Jul  3 08:46:40 zumbi kernel: [   31.104671] Trying to unpack rootfs image as initramfs...
Jul  3 08:46:40 zumbi kernel: [   31.170961] Freeing initrd memory: 3497k freed
Jul  3 08:46:40 zumbi kernel: [   31.172079] kvm: already loaded the other module
Jul  3 08:46:40 zumbi kernel: [   31.172658] [ds] bts selftest...no resume progress/overflow...passed.
Jul  3 08:46:40 zumbi kernel: [   31.176515] microcode: CPU0 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.177104] microcode: CPU1 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.177689] microcode: CPU2 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.178274] microcode: CPU3 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.178861] microcode: CPU4 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.179451] microcode: CPU5 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.180037] microcode: CPU6 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.180623] microcode: CPU7 sig=0x106a2, pf=0x2, revision=0xffff0013
Jul  3 08:46:40 zumbi kernel: [   31.181231] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
Jul  3 08:46:40 zumbi kernel: [   31.182109] Scanning for low memory corruption every 60 seconds
Jul  3 08:46:40 zumbi kernel: [   31.182809] audit: initializing netlink socket (disabled)
Jul  3 08:46:40 zumbi kernel: [   31.183353] type=2000 audit(1246607182.843:1): initialized
Jul  3 08:46:40 zumbi kernel: [   31.194055] HugeTLB registered 2 MB page size, pre-allocated 0 pages
Jul  3 08:46:40 zumbi kernel: [   31.196233] VFS: Disk quotas dquot_6.5.2
Jul  3 08:46:40 zumbi kernel: [   31.196744] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Jul  3 08:46:40 zumbi kernel: [   31.197846] msgmni has been set to 7894
Jul  3 08:46:40 zumbi kernel: [   31.198375] SELinux:  Registering netfilter hooks
Jul  3 08:46:40 zumbi kernel: [   31.198644] alg: No test for stdrng (krng)
Jul  3 08:46:40 zumbi kernel: [   31.199178] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
Jul  3 08:46:40 zumbi kernel: [   31.200035] io scheduler noop registered
Jul  3 08:46:40 zumbi kernel: [   31.200496] io scheduler anticipatory registered
Jul  3 08:46:40 zumbi kernel: [   31.200990] io scheduler deadline registered
Jul  3 08:46:40 zumbi kernel: [   31.201474] io scheduler cfq registered (default)
Jul  3 08:46:40 zumbi kernel: [   31.201990] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10
Jul  3 08:46:40 zumbi kernel: [   31.201992] pci 0000:00:1a.0: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   31.202005] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010
Jul  3 08:46:40 zumbi kernel: [   31.202007] pci 0000:00:1a.1: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   31.202020] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010
Jul  3 08:46:40 zumbi kernel: [   31.202022] pci 0000:00:1a.2: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   31.202154] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
Jul  3 08:46:40 zumbi kernel: [   31.202155] pci 0000:00:1d.0: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   31.202168] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
Jul  3 08:46:40 zumbi kernel: [   31.202169] pci 0000:00:1d.1: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   31.202183] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
Jul  3 08:46:40 zumbi kernel: [   31.202184] pci 0000:00:1d.2: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   31.202349] pci 0000:05:00.0: Boot video device
Jul  3 08:46:40 zumbi kernel: [   31.202445] pcieport-driver 0000:00:01.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.202543] pcieport-driver 0000:00:03.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.202637] pcieport-driver 0000:00:07.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.202733] pcieport-driver 0000:00:1c.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.202832] pcieport-driver 0000:00:1c.1: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.202932] pcieport-driver 0000:00:1c.4: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.203111] aer 0000:00:01.0:pcie02: AER service couldn't init device: no _OSC support
Jul  3 08:46:40 zumbi kernel: [   31.203116] aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support
Jul  3 08:46:40 zumbi kernel: [   31.203119] aer 0000:00:07.0:pcie02: AER service couldn't init device: no _OSC support
Jul  3 08:46:40 zumbi kernel: [   31.203138] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Jul  3 08:46:40 zumbi kernel: [   31.203832] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
Jul  3 08:46:40 zumbi kernel: [   31.204689] ACPI: Power Button [PWRF]
Jul  3 08:46:40 zumbi kernel: [   31.205188] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
Jul  3 08:46:40 zumbi kernel: [   31.206084] ACPI: Sleep Button [SLPB]
Jul  3 08:46:40 zumbi kernel: [   31.206976] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.207903]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.208396] Monitor-Mwait will be used to enter C-1 state
Jul  3 08:46:40 zumbi kernel: [   31.208411] Monitor-Mwait will be used to enter C-2 state
Jul  3 08:46:40 zumbi kernel: [   31.208424] Monitor-Mwait will be used to enter C-3 state
Jul  3 08:46:40 zumbi kernel: [   31.208455] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.209220] processor ACPI_CPU:00: registered as cooling_device0
Jul  3 08:46:40 zumbi kernel: [   31.209786] ACPI: Processor [CPU0] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.210831] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.211759]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.212312] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.213079] processor ACPI_CPU:02: registered as cooling_device1
Jul  3 08:46:40 zumbi kernel: [   31.213647] ACPI: Processor [CPU2] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.220019] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.220946]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.221501] ACPI: CPU2 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.222265] processor ACPI_CPU:04: registered as cooling_device2
Jul  3 08:46:40 zumbi kernel: [   31.222833] ACPI: Processor [CPU4] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.223880] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.224805]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.225360] ACPI: CPU3 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.226124] processor ACPI_CPU:06: registered as cooling_device3
Jul  3 08:46:40 zumbi kernel: [   31.226693] ACPI: Processor [CPU6] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.227747] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.228674]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.229230] ACPI: CPU4 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.229995] processor ACPI_CPU:08: registered as cooling_device4
Jul  3 08:46:40 zumbi kernel: [   31.230564] ACPI: Processor [CPU8] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.231611] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.232537]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.233080] ACPI: CPU5 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.233845] processor ACPI_CPU:0a: registered as cooling_device5
Jul  3 08:46:40 zumbi kernel: [   31.234415] ACPI: Processor [CPUA] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.235462] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.236388]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.236930] ACPI: CPU6 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.237699] processor ACPI_CPU:0c: registered as cooling_device6
Jul  3 08:46:40 zumbi kernel: [   31.238267] ACPI: Processor [CPUC] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.239318] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset
Jul  3 08:46:40 zumbi kernel: [   31.240243]  [20090320]
Jul  3 08:46:40 zumbi kernel: [   31.240786] ACPI: CPU7 (power states: C1[C1] C2[C2] C3[C3])
Jul  3 08:46:40 zumbi kernel: [   31.241552] processor ACPI_CPU:0e: registered as cooling_device7
Jul  3 08:46:40 zumbi kernel: [   31.242119] ACPI: Processor [CPUE] (supports 8 throttling states)
Jul  3 08:46:40 zumbi kernel: [   31.244124] ***blkif_init
Jul  3 08:46:40 zumbi kernel: [   31.244525] *** netif_init
Jul  3 08:46:40 zumbi kernel: [   31.244926] xenfs: not registering filesystem on non-xen platform
Jul  3 08:46:40 zumbi kernel: [   31.247115] Non-volatile memory driver v1.3
Jul  3 08:46:40 zumbi kernel: [   31.247649] Linux agpgart interface v0.103
Jul  3 08:46:40 zumbi kernel: [   31.248170] [drm] Initialized drm 1.1.0 20060810
Jul  3 08:46:40 zumbi kernel: [   31.248708] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Jul  3 08:46:40 zumbi kernel: [   31.493028] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
Jul  3 08:46:40 zumbi kernel: [   31.493802]   alloc irq_desc for 18 on node -1
Jul  3 08:46:40 zumbi kernel: [   31.493803]   alloc kstat_irqs on node -1
Jul  3 08:46:40 zumbi kernel: [   31.493808] serial 0000:0a:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Jul  3 08:46:40 zumbi kernel: [   31.494499] 0000:0a:02.0: ttyS0 at I/O 0x1000 (irq = 18) is a 16550A
Jul  3 08:46:40 zumbi kernel: [   31.495429] 0000:0a:02.0: ttyS2 at I/O 0x1008 (irq = 18) is a 16550A
Jul  3 08:46:40 zumbi kernel: [   31.497226] brd: module loaded
Jul  3 08:46:40 zumbi kernel: [   31.498213] loop: module loaded
Jul  3 08:46:40 zumbi kernel: [   31.498799] input: Macintosh mouse button emulation as /devices/virtual/input/input2
Jul  3 08:46:40 zumbi kernel: [   31.500040] Driver 'sd' needs updating - please use bus_type methods
Jul  3 08:46:40 zumbi kernel: [   31.500893] Driver 'sr' needs updating - please use bus_type methods
Jul  3 08:46:40 zumbi kernel: [   31.501781] ahci 0000:09:00.0: version 3.0
Jul  3 08:46:40 zumbi kernel: [   31.501789] ahci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  3 08:46:40 zumbi kernel: [   31.502674] ahci 0000:09:00.0: controller can't do NCQ, turning off CAP_NCQ
Jul  3 08:46:40 zumbi kernel: [   31.503562] ahci 0000:09:00.0: controller can't do PMP, turning off CAP_PMP
Jul  3 08:46:40 zumbi kernel: [   31.504450] ahci 0000:09:00.0: MV_AHCI HACK: port_map 7 -> 3
Jul  3 08:46:40 zumbi kernel: [   31.505219] ahci 0000:09:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
Jul  3 08:46:40 zumbi kernel: [   31.506645] ahci: SSS flag set, parallel bus scan disabled
Jul  3 08:46:40 zumbi kernel: [   31.507433] ahci 0000:09:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
Jul  3 08:46:40 zumbi kernel: [   31.508634] ahci 0000:09:00.0: flags: 64bit stag led slum part 
Jul  3 08:46:40 zumbi kernel: [   31.509432] ahci 0000:09:00.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   31.509513] scsi0 : ahci
Jul  3 08:46:40 zumbi kernel: [   31.510080] scsi1 : ahci
Jul  3 08:46:40 zumbi kernel: [   31.510633] scsi2 : ahci
Jul  3 08:46:40 zumbi kernel: [   31.511182] ata1: SATA max UDMA/133 abar m1024@0xb7000000 port 0xb7000100 irq 16
Jul  3 08:46:40 zumbi kernel: [   31.512331] ata2: SATA max UDMA/133 abar m1024@0xb7000000 port 0xb7000180 irq 16
Jul  3 08:46:40 zumbi kernel: [   31.513477] ata3: DUMMY
Jul  3 08:46:40 zumbi kernel: [   31.818815] ata1: SATA link down (SStatus 0 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   32.123705] ata2: SATA link down (SStatus 0 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   32.124500] ata_piix 0000:00:1f.2: version 2.13
Jul  3 08:46:40 zumbi kernel: [   32.124506]   alloc irq_desc for 19 on node -1
Jul  3 08:46:40 zumbi kernel: [   32.124507]   alloc kstat_irqs on node -1
Jul  3 08:46:40 zumbi kernel: [   32.124511] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Jul  3 08:46:40 zumbi kernel: [   32.125422] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
Jul  3 08:46:40 zumbi kernel: [   32.126413] ata_piix 0000:00:1f.2: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   32.126446] scsi3 : ata_piix
Jul  3 08:46:40 zumbi kernel: [   32.127032] scsi4 : ata_piix
Jul  3 08:46:40 zumbi kernel: [   32.127661] ata4: SATA max UDMA/133 cmd 0x5138 ctl 0x514c bmdma 0x5110 irq 19
Jul  3 08:46:40 zumbi kernel: [   32.128569] ata5: SATA max UDMA/133 cmd 0x5130 ctl 0x5148 bmdma 0x5118 irq 19
Jul  3 08:46:40 zumbi kernel: [   32.889491] ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   32.890350] ata4.01: SATA link down (SStatus 0 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   32.909636] ata4.00: ATAPI: PIONEER BD-ROM  BDC-202, 1.04, max UDMA/66
Jul  3 08:46:40 zumbi kernel: [   32.916641] ata4.00: configured for UDMA/66
Jul  3 08:46:40 zumbi kernel: [   32.930184] scsi 3:0:0:0: CD-ROM            PIONEER  BD-ROM  BDC-202  1.04 PQ: 0 ANSI: 5
Jul  3 08:46:40 zumbi kernel: [   32.953425] sr0: scsi3-mmc drive: 32x/32x writer dvd-ram cd/rw xa/form2 cdda tray
Jul  3 08:46:40 zumbi kernel: [   32.954587] Uniform CD-ROM driver Revision: 3.20
Jul  3 08:46:40 zumbi kernel: [   32.955352] sr 3:0:0:0: Attached scsi CD-ROM sr0
Jul  3 08:46:40 zumbi kernel: [   32.955407] sr 3:0:0:0: Attached scsi generic sg0 type 5
Jul  3 08:46:40 zumbi kernel: [   33.716192] ata5.00: SATA link down (SStatus 0 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   33.716981] ata5.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   33.731703] ata5.01: ATA-8: ST3500320AS, SD15, max UDMA/133
Jul  3 08:46:40 zumbi kernel: [   33.732473] ata5.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Jul  3 08:46:40 zumbi kernel: [   33.739728] ata5.01: configured for UDMA/133
Jul  3 08:46:40 zumbi kernel: [   33.740425] scsi 4:0:1:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
Jul  3 08:46:40 zumbi kernel: [   33.741731] sd 4:0:1:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
Jul  3 08:46:40 zumbi kernel: [   33.742909] sd 4:0:1:0: [sda] Write Protect is off
Jul  3 08:46:40 zumbi kernel: [   33.743605] sd 4:0:1:0: [sda] Mode Sense: 00 3a 00 00
Jul  3 08:46:40 zumbi kernel: [   33.743618] sd 4:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul  3 08:46:40 zumbi kernel: [   33.744964]  sda: sda1 sda2 < sda5 >
Jul  3 08:46:40 zumbi kernel: [   33.771758] sd 4:0:1:0: [sda] Attached SCSI disk
Jul  3 08:46:40 zumbi kernel: [   33.772490] sd 4:0:1:0: Attached scsi generic sg1 type 0
Jul  3 08:46:40 zumbi kernel: [   33.773267] ata_piix 0000:00:1f.5: PCI INT B -> GSI 18 (level, low) -> IRQ 18
Jul  3 08:46:40 zumbi kernel: [   33.774173] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
Jul  3 08:46:40 zumbi kernel: [   33.775162] ata_piix 0000:00:1f.5: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   33.775197] scsi5 : ata_piix
Jul  3 08:46:40 zumbi kernel: [   33.775784] scsi6 : ata_piix
Jul  3 08:46:40 zumbi kernel: [   33.776388] ata6: SATA max UDMA/133 cmd 0x5128 ctl 0x5144 bmdma 0x50f0 irq 18
Jul  3 08:46:40 zumbi kernel: [   33.777295] ata7: SATA max UDMA/133 cmd 0x5120 ctl 0x5140 bmdma 0x50f8 irq 18
Jul  3 08:46:40 zumbi kernel: [   34.093783] ata6: SATA link down (SStatus 0 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   34.549878] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul  3 08:46:40 zumbi kernel: [   34.553408] ata7.00: ATA-8: ST3500320AS, SD15, max UDMA/133
Jul  3 08:46:40 zumbi kernel: [   34.554177] ata7.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
Jul  3 08:46:40 zumbi kernel: [   34.561438] ata7.00: configured for UDMA/133
Jul  3 08:46:40 zumbi kernel: [   34.562131] scsi 6:0:0:0: Direct-Access     ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
Jul  3 08:46:40 zumbi kernel: [   34.563446] sd 6:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
Jul  3 08:46:40 zumbi kernel: [   34.564625] sd 6:0:0:0: [sdb] Write Protect is off
Jul  3 08:46:40 zumbi kernel: [   34.565321] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Jul  3 08:46:40 zumbi kernel: [   34.565333] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul  3 08:46:40 zumbi kernel: [   34.566671]  sdb:
Jul  3 08:46:40 zumbi kernel: [   34.590434] sd 6:0:0:0: [sdb] Attached SCSI disk
Jul  3 08:46:40 zumbi kernel: [   34.591168] sd 6:0:0:0: Attached scsi generic sg2 type 0
Jul  3 08:46:40 zumbi kernel: [   34.592079] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
Jul  3 08:46:40 zumbi kernel: [   34.592922] Copyright (c) 1999-2006 Intel Corporation.
Jul  3 08:46:40 zumbi kernel: [   34.593677] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.4-k4
Jul  3 08:46:40 zumbi kernel: [   34.594489] e1000e: Copyright (c) 1999-2008 Intel Corporation.
Jul  3 08:46:40 zumbi kernel: [   34.595330] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
Jul  3 08:46:40 zumbi kernel: [   34.596139] e100: Copyright(c) 1999-2006 Intel Corporation
Jul  3 08:46:40 zumbi kernel: [   34.596933] tg3.c:v3.98 (February 25, 2009)
Jul  3 08:46:40 zumbi kernel: [   34.597625] tg3 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jul  3 08:46:40 zumbi kernel: [   34.598555] tg3 0000:08:00.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.600264] tg3 0000:08:00.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   34.607323] eth0: Tigon3 [partno(BCM95721A211F) rev 4201] (PCI Express) MAC address 00:10:18:32:51:a2
Jul  3 08:46:40 zumbi kernel: [   34.608634] eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
Jul  3 08:46:40 zumbi kernel: [   34.609798] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
Jul  3 08:46:40 zumbi kernel: [   34.610630] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
Jul  3 08:46:40 zumbi kernel: [   34.611413] sky2 driver version 1.22
Jul  3 08:46:40 zumbi kernel: [   34.612126] console [netcon0] enabled
Jul  3 08:46:40 zumbi kernel: [   34.612721] netconsole: network logging started
Jul  3 08:46:40 zumbi kernel: [   34.613475] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jul  3 08:46:40 zumbi kernel: [   34.614327] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
Jul  3 08:46:40 zumbi kernel: [   34.614340] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Jul  3 08:46:40 zumbi kernel: [   34.615250] ehci_hcd 0000:00:1a.7: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.615253] ehci_hcd 0000:00:1a.7: EHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.616018] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file 'devices'
Jul  3 08:46:40 zumbi kernel: [   34.616021] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.616054] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
Jul  3 08:46:40 zumbi kernel: [   34.617207] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
Jul  3 08:46:40 zumbi kernel: [   34.617210] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
Jul  3 08:46:40 zumbi kernel: [   34.617222] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  3 08:46:40 zumbi kernel: [   34.621116] ehci_hcd 0000:00:1a.7: debug port 1
Jul  3 08:46:40 zumbi kernel: [   34.621792] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
Jul  3 08:46:40 zumbi kernel: [   34.621793] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.621796] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xb7201400
Jul  3 08:46:40 zumbi kernel: [   34.622570] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  3 08:46:40 zumbi kernel: [   34.626451] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
Jul  3 08:46:40 zumbi kernel: [   34.631798] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
Jul  3 08:46:40 zumbi kernel: [   34.632595] usb usb1: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.632599] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jul  3 08:46:40 zumbi kernel: [   34.633472] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.634601] usb usb1: Product: EHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.635304] usb usb1: Manufacturer: Linux 2.6.30-rc6-tip ehci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.636113] usb usb1: SerialNumber: 0000:00:1a.7
Jul  3 08:46:40 zumbi kernel: [   34.636813] usb usb1: uevent
Jul  3 08:46:40 zumbi kernel: [   34.636838] usb usb1: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.636839] usb usb1: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.637606] usb usb1: adding 1-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.637615] usb 1-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.637638] hub 1-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.637639] hub 1-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.637641] hub 1-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.638246] hub 1-0:1.0: 6 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.638868] hub 1-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.638869] hub 1-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.638871] hub 1-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.638872] hub 1-0:1.0: power on to power good time: 20ms
Jul  3 08:46:40 zumbi kernel: [   34.638875] hub 1-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.638876] hub 1-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.638948] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.638992]   alloc irq_desc for 23 on node -1
Jul  3 08:46:40 zumbi kernel: [   34.638993]   alloc kstat_irqs on node -1
Jul  3 08:46:40 zumbi kernel: [   34.638997] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Jul  3 08:46:40 zumbi kernel: [   34.639909] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.639911] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.640671] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002'
Jul  3 08:46:40 zumbi kernel: [   34.640704] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
Jul  3 08:46:40 zumbi kernel: [   34.641856] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
Jul  3 08:46:40 zumbi kernel: [   34.641859] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr
Jul  3 08:46:40 zumbi kernel: [   34.641870] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  3 08:46:40 zumbi kernel: [   34.645770] ehci_hcd 0000:00:1d.7: debug port 1
Jul  3 08:46:40 zumbi kernel: [   34.646445] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
Jul  3 08:46:40 zumbi kernel: [   34.646446] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.646455] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb7201000
Jul  3 08:46:40 zumbi kernel: [   34.647229] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
Jul  3 08:46:40 zumbi kernel: [   34.651104] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
Jul  3 08:46:40 zumbi kernel: [   34.656784] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Jul  3 08:46:40 zumbi kernel: [   34.657591] usb usb2: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.657595] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
Jul  3 08:46:40 zumbi kernel: [   34.658467] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.659597] usb usb2: Product: EHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.660298] usb usb2: Manufacturer: Linux 2.6.30-rc6-tip ehci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.661107] usb usb2: SerialNumber: 0000:00:1d.7
Jul  3 08:46:40 zumbi kernel: [   34.661806] usb usb2: uevent
Jul  3 08:46:40 zumbi kernel: [   34.661830] usb usb2: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.661832] usb usb2: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.662600] usb usb2: adding 2-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.662610] usb 2-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.662633] hub 2-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.662634] hub 2-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.662636] hub 2-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.663240] hub 2-0:1.0: 6 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.663865] hub 2-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.663866] hub 2-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.663867] hub 2-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.663868] hub 2-0:1.0: power on to power good time: 20ms
Jul  3 08:46:40 zumbi kernel: [   34.663871] hub 2-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.663872] hub 2-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.663919] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.663978] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jul  3 08:46:40 zumbi kernel: [   34.664798] ohci_hcd: block sizes: ed 80 td 96
Jul  3 08:46:40 zumbi kernel: [   34.664827] uhci_hcd: USB Universal Host Controller Interface driver
Jul  3 08:46:40 zumbi kernel: [   34.665674] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul  3 08:46:40 zumbi kernel: [   34.666581] uhci_hcd 0000:00:1a.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.666583] uhci_hcd 0000:00:1a.0: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.672668] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '003'
Jul  3 08:46:40 zumbi kernel: [   34.672701] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
Jul  3 08:46:40 zumbi kernel: [   34.673853] uhci_hcd 0000:00:1a.0: detected 2 ports
Jul  3 08:46:40 zumbi kernel: [   34.674556] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
Jul  3 08:46:40 zumbi kernel: [   34.674558] uhci_hcd 0000:00:1a.0: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   34.674570] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.674573] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000050c0
Jul  3 08:46:40 zumbi kernel: [   34.675371] usb usb3: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.675375] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
Jul  3 08:46:40 zumbi kernel: [   34.676248] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.677378] usb usb3: Product: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.678080] usb usb3: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.678889] usb usb3: SerialNumber: 0000:00:1a.0
Jul  3 08:46:40 zumbi kernel: [   34.679587] usb usb3: uevent
Jul  3 08:46:40 zumbi kernel: [   34.679610] usb usb3: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.679612] usb usb3: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.680381] usb usb3: adding 3-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.680390] usb 3-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.680412] hub 3-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.680414] hub 3-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.680415] hub 3-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.681017] hub 3-0:1.0: 2 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.681642] hub 3-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.681643] hub 3-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.681644] hub 3-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.681645] hub 3-0:1.0: power on to power good time: 2ms
Jul  3 08:46:40 zumbi kernel: [   34.681648] hub 3-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.681649] hub 3-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.681685] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.681735]   alloc irq_desc for 21 on node -1
Jul  3 08:46:40 zumbi kernel: [   34.681736]   alloc kstat_irqs on node -1
Jul  3 08:46:40 zumbi kernel: [   34.681739] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
Jul  3 08:46:40 zumbi kernel: [   34.682647] uhci_hcd 0000:00:1a.1: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.682649] uhci_hcd 0000:00:1a.1: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.683410] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '004'
Jul  3 08:46:40 zumbi kernel: [   34.683443] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
Jul  3 08:46:40 zumbi kernel: [   34.684595] uhci_hcd 0000:00:1a.1: detected 2 ports
Jul  3 08:46:40 zumbi kernel: [   34.685298] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
Jul  3 08:46:40 zumbi kernel: [   34.685299] uhci_hcd 0000:00:1a.1: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   34.685312] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.685320] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000050a0
Jul  3 08:46:40 zumbi kernel: [   34.686117] usb usb4: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.686121] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
Jul  3 08:46:40 zumbi kernel: [   34.686993] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.688119] usb usb4: Product: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.688822] usb usb4: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.689632] usb usb4: SerialNumber: 0000:00:1a.1
Jul  3 08:46:40 zumbi kernel: [   34.690331] usb usb4: uevent
Jul  3 08:46:40 zumbi kernel: [   34.690354] usb usb4: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.690355] usb usb4: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.691120] usb usb4: adding 4-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.691129] usb 4-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.691152] hub 4-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.691153] hub 4-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.691154] hub 4-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.691756] hub 4-0:1.0: 2 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.692382] hub 4-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.692383] hub 4-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.692384] hub 4-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.692386] hub 4-0:1.0: power on to power good time: 2ms
Jul  3 08:46:40 zumbi kernel: [   34.692388] hub 4-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.692389] hub 4-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.692427] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.692475] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
Jul  3 08:46:40 zumbi kernel: [   34.693382] uhci_hcd 0000:00:1a.2: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.693384] uhci_hcd 0000:00:1a.2: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.694143] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '005'
Jul  3 08:46:40 zumbi kernel: [   34.694177] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
Jul  3 08:46:40 zumbi kernel: [   34.695329] uhci_hcd 0000:00:1a.2: detected 2 ports
Jul  3 08:46:40 zumbi kernel: [   34.696031] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
Jul  3 08:46:40 zumbi kernel: [   34.696032] uhci_hcd 0000:00:1a.2: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   34.696044] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.696048] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00005080
Jul  3 08:46:40 zumbi kernel: [   34.696847] usb usb5: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.696851] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
Jul  3 08:46:40 zumbi kernel: [   34.697724] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.698852] usb usb5: Product: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.699553] usb usb5: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.700363] usb usb5: SerialNumber: 0000:00:1a.2
Jul  3 08:46:40 zumbi kernel: [   34.701059] usb usb5: uevent
Jul  3 08:46:40 zumbi kernel: [   34.701082] usb usb5: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.701084] usb usb5: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.701851] usb usb5: adding 5-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.701861] usb 5-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.701888] hub 5-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.701889] hub 5-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.701891] hub 5-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.702495] hub 5-0:1.0: 2 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.703118] hub 5-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.703119] hub 5-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.703120] hub 5-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.703121] hub 5-0:1.0: power on to power good time: 2ms
Jul  3 08:46:40 zumbi kernel: [   34.703123] hub 5-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.703124] hub 5-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.703165] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.703214] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Jul  3 08:46:40 zumbi kernel: [   34.704119] uhci_hcd 0000:00:1d.0: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.704122] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.704886] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '006'
Jul  3 08:46:40 zumbi kernel: [   34.704920] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
Jul  3 08:46:40 zumbi kernel: [   34.706073] uhci_hcd 0000:00:1d.0: detected 2 ports
Jul  3 08:46:40 zumbi kernel: [   34.706777] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
Jul  3 08:46:40 zumbi kernel: [   34.706778] uhci_hcd 0000:00:1d.0: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   34.706790] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.706794] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00005060
Jul  3 08:46:40 zumbi kernel: [   34.707591] usb usb6: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.707595] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
Jul  3 08:46:40 zumbi kernel: [   34.708466] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.709597] usb usb6: Product: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.710300] usb usb6: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.711109] usb usb6: SerialNumber: 0000:00:1d.0
Jul  3 08:46:40 zumbi kernel: [   34.711808] usb usb6: uevent
Jul  3 08:46:40 zumbi kernel: [   34.711833] usb usb6: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.711835] usb usb6: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.712606] usb usb6: adding 6-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.712615] usb 6-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.712638] hub 6-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.712639] hub 6-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.712640] hub 6-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.713245] hub 6-0:1.0: 2 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.713867] hub 6-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.713868] hub 6-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.713869] hub 6-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.713871] hub 6-0:1.0: power on to power good time: 2ms
Jul  3 08:46:40 zumbi kernel: [   34.713873] hub 6-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.713874] hub 6-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.713912] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.713963] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Jul  3 08:46:40 zumbi kernel: [   34.714872] uhci_hcd 0000:00:1d.1: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.714874] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.715640] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '007'
Jul  3 08:46:40 zumbi kernel: [   34.715681] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
Jul  3 08:46:40 zumbi kernel: [   34.716840] uhci_hcd 0000:00:1d.1: detected 2 ports
Jul  3 08:46:40 zumbi kernel: [   34.717543] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
Jul  3 08:46:40 zumbi kernel: [   34.717544] uhci_hcd 0000:00:1d.1: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   34.717557] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.717560] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00005040
Jul  3 08:46:40 zumbi kernel: [   34.718359] usb usb7: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.718363] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
Jul  3 08:46:40 zumbi kernel: [   34.719235] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.720363] usb usb7: Product: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.721064] usb usb7: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.721874] usb usb7: SerialNumber: 0000:00:1d.1
Jul  3 08:46:40 zumbi kernel: [   34.722577] usb usb7: uevent
Jul  3 08:46:40 zumbi kernel: [   34.722601] usb usb7: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.722603] usb usb7: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.723374] usb usb7: adding 7-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.723383] usb 7-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.723407] hub 7-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.723408] hub 7-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.723410] hub 7-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.724011] hub 7-0:1.0: 2 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.724636] hub 7-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.724637] hub 7-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.724638] hub 7-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.724639] hub 7-0:1.0: power on to power good time: 2ms
Jul  3 08:46:40 zumbi kernel: [   34.724641] hub 7-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.724643] hub 7-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.724682] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.724731] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Jul  3 08:46:40 zumbi kernel: [   34.725638] uhci_hcd 0000:00:1d.2: setting latency timer to 64
Jul  3 08:46:40 zumbi kernel: [   34.725640] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.726402] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '008'
Jul  3 08:46:40 zumbi kernel: [   34.726439] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
Jul  3 08:46:40 zumbi kernel: [   34.727600] uhci_hcd 0000:00:1d.2: detected 2 ports
Jul  3 08:46:40 zumbi kernel: [   34.728304] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
Jul  3 08:46:40 zumbi kernel: [   34.728306] uhci_hcd 0000:00:1d.2: Performing full reset
Jul  3 08:46:40 zumbi kernel: [   34.728318] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
Jul  3 08:46:40 zumbi kernel: [   34.728321] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005020
Jul  3 08:46:40 zumbi kernel: [   34.729117] usb usb8: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   34.729122] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
Jul  3 08:46:40 zumbi kernel: [   34.729993] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Jul  3 08:46:40 zumbi kernel: [   34.731120] usb usb8: Product: UHCI Host Controller
Jul  3 08:46:40 zumbi kernel: [   34.731821] usb usb8: Manufacturer: Linux 2.6.30-rc6-tip uhci_hcd
Jul  3 08:46:40 zumbi kernel: [   34.732631] usb usb8: SerialNumber: 0000:00:1d.2
Jul  3 08:46:40 zumbi kernel: [   34.733330] usb usb8: uevent
Jul  3 08:46:40 zumbi kernel: [   34.733354] usb usb8: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   34.733355] usb usb8: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   34.734127] usb usb8: adding 8-0:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   34.734136] usb 8-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.734159] hub 8-0:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   34.734160] hub 8-0:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   34.734161] hub 8-0:1.0: USB hub found
Jul  3 08:46:40 zumbi kernel: [   34.734764] hub 8-0:1.0: 2 ports detected
Jul  3 08:46:40 zumbi kernel: [   34.735390] hub 8-0:1.0: standalone hub
Jul  3 08:46:40 zumbi kernel: [   34.735391] hub 8-0:1.0: no power switching (usb 1.0)
Jul  3 08:46:40 zumbi kernel: [   34.735392] hub 8-0:1.0: individual port over-current protection
Jul  3 08:46:40 zumbi kernel: [   34.735393] hub 8-0:1.0: power on to power good time: 2ms
Jul  3 08:46:40 zumbi kernel: [   34.735395] hub 8-0:1.0: local power source is good
Jul  3 08:46:40 zumbi kernel: [   34.735397] hub 8-0:1.0: trying to enable port power on non-switchable hub
Jul  3 08:46:40 zumbi kernel: [   34.735436] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '001'
Jul  3 08:46:40 zumbi kernel: [   34.735530] usbcore: registered new interface driver usblp
Jul  3 08:46:40 zumbi kernel: [   34.736289] Initializing USB Mass Storage driver...
Jul  3 08:46:40 zumbi kernel: [   34.737032] usbcore: registered new interface driver usb-storage
Jul  3 08:46:40 zumbi kernel: [   34.737847] USB Mass Storage support registered.
Jul  3 08:46:40 zumbi kernel: [   34.738566] usbcore: registered new interface driver libusual
Jul  3 08:46:40 zumbi kernel: [   34.739371] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.739449] PNP: No PS/2 controller found. Probing ports directly.
Jul  3 08:46:40 zumbi kernel: [   34.743070] serio: i8042 KBD port at 0x60,0x64 irq 1
Jul  3 08:46:40 zumbi kernel: [   34.743783] serio: i8042 AUX port at 0x60,0x64 irq 12
Jul  3 08:46:40 zumbi kernel: [   34.744582] mice: PS/2 mouse device common for all mice
Jul  3 08:46:40 zumbi kernel: [   34.745476] rtc_cmos 00:02: RTC can wake from S4
Jul  3 08:46:40 zumbi kernel: [   34.746203] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
Jul  3 08:46:40 zumbi kernel: [   34.747036] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
Jul  3 08:46:40 zumbi kernel: [   34.747940] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
Jul  3 08:46:40 zumbi kernel: [   34.749231] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
Jul  3 08:46:40 zumbi kernel: [   34.751302] cpuidle: using governor ladder
Jul  3 08:46:40 zumbi kernel: [   34.753299] cpuidle: using governor menu
Jul  3 08:46:40 zumbi kernel: [   34.754546] usbcore: registered new interface driver hiddev
Jul  3 08:46:40 zumbi kernel: [   34.755353] usbcore: registered new interface driver usbhid
Jul  3 08:46:40 zumbi kernel: [   34.756123] usbhid: v2.6:USB HID core driver
Jul  3 08:46:40 zumbi kernel: [   34.756871] Advanced Linux Sound Architecture Driver Version 1.0.20.
Jul  3 08:46:40 zumbi kernel: [   34.759841] modprobe used greatest stack depth: 5904 bytes left
Jul  3 08:46:40 zumbi kernel: [   34.760874] ALSA device list:
Jul  3 08:46:40 zumbi kernel: [   34.761409]   No soundcards found.
Jul  3 08:46:40 zumbi kernel: [   34.762054] Netfilter messages via NETLINK v0.30.
Jul  3 08:46:40 zumbi kernel: [   34.762803] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
Jul  3 08:46:40 zumbi kernel: [   34.763857] ctnetlink v0.93: registering with nfnetlink.
Jul  3 08:46:40 zumbi kernel: [   34.764665] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
Jul  3 08:46:40 zumbi kernel: [   34.764669] hub 2-0:1.0: port 1: status 0501 change 0001
Jul  3 08:46:40 zumbi kernel: [   34.764676] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
Jul  3 08:46:40 zumbi kernel: [   34.764678] hub 2-0:1.0: port 2: status 0501 change 0001
Jul  3 08:46:40 zumbi kernel: [   34.765049] ip_tables: (C) 2000-2006 Netfilter Core Team
Jul  3 08:46:40 zumbi kernel: [   34.765855] TCP cubic registered
Jul  3 08:46:40 zumbi kernel: [   34.766462] Initializing XFRM netlink socket
Jul  3 08:46:40 zumbi kernel: [   34.767542] NET: Registered protocol family 10
Jul  3 08:46:40 zumbi kernel: [   34.768999] ip6_tables: (C) 2000-2006 Netfilter Core Team
Jul  3 08:46:40 zumbi kernel: [   34.769829] IPv6 over IPv4 tunneling driver
Jul  3 08:46:40 zumbi kernel: [   34.771014] NET: Registered protocol family 17
Jul  3 08:46:40 zumbi kernel: [   34.771999] RPC: Registered udp transport module.
Jul  3 08:46:40 zumbi kernel: [   34.772689] RPC: Registered tcp transport module.
Jul  3 08:46:40 zumbi kernel: [   34.775884] PM: Resume from disk failed.
Jul  3 08:46:40 zumbi kernel: [   34.775892] registered taskstats version 1
Jul  3 08:46:40 zumbi kernel: [   34.776633]   Magic number: 1:207:773
Jul  3 08:46:40 zumbi kernel: [   34.777277] hub 2-0:1.0: hash matches
Jul  3 08:46:40 zumbi kernel: [   34.777988] Freeing unused kernel memory: 504k freed
Jul  3 08:46:40 zumbi kernel: [   34.778857] Write protecting the kernel read-only data: 7936k
Jul  3 08:46:40 zumbi kernel: [   34.781131] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.792160] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.804137] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.815706] uhci_hcd 0000:00:1d.0: port 1 portsc 008a,00
Jul  3 08:46:40 zumbi kernel: [   34.815717] uhci_hcd 0000:00:1d.0: port 2 portsc 008a,00
Jul  3 08:46:40 zumbi kernel: [   34.824144] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.832619] console_setup used greatest stack depth: 5552 bytes left
Jul  3 08:46:40 zumbi kernel: [   34.835423] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.859725] usb usb3: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859737] usb 3-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859799] usb usb4: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859810] usb 4-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859862] usb usb5: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859873] usb 5-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859926] usb usb1: uevent
Jul  3 08:46:40 zumbi kernel: [   34.859936] usb 1-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860169] usb usb6: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860180] usb 6-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860234] usb usb7: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860244] usb 7-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860297] usb usb8: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860308] usb 8-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860360] usb usb2: uevent
Jul  3 08:46:40 zumbi kernel: [   34.860371] usb 2-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   34.864180] hub 2-0:1.0: state 7 ports 6 chg 0006 evt 0000
Jul  3 08:46:40 zumbi kernel: [   34.864189] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
Jul  3 08:46:40 zumbi kernel: [   34.864195] ehci_hcd 0000:00:1d.7: port 1 low speed --> companion
Jul  3 08:46:40 zumbi kernel: [   34.916014] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
Jul  3 08:46:40 zumbi kernel: [   34.916036] hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
Jul  3 08:46:40 zumbi kernel: [   34.916043] ehci_hcd 0000:00:1d.7: port 2 low speed --> companion
Jul  3 08:46:40 zumbi kernel: [   34.919673] scsi_id used greatest stack depth: 5504 bytes left
Jul  3 08:46:40 zumbi kernel: [   34.967023] ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
Jul  3 08:46:40 zumbi kernel: [   34.967042] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0004
Jul  3 08:46:40 zumbi kernel: [   34.967047] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0006
Jul  3 08:46:40 zumbi kernel: [   34.967053] uhci_hcd 0000:00:1d.0: port 1 portsc 01a3,00
Jul  3 08:46:40 zumbi kernel: [   34.967058] hub 6-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
Jul  3 08:46:40 zumbi kernel: [   34.968638] scsi_id used greatest stack depth: 5040 bytes left
Jul  3 08:46:40 zumbi kernel: [   35.070055] hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
Jul  3 08:46:40 zumbi kernel: [   35.089682] PM: Starting manual resume from disk
Jul  3 08:46:40 zumbi kernel: [   35.090386] PM: Resume from partition 8:5
Jul  3 08:46:40 zumbi kernel: [   35.090387] PM: Checking hibernation image.
Jul  3 08:46:40 zumbi kernel: [   35.090794] PM: Resume from disk failed.
Jul  3 08:46:40 zumbi kernel: [   35.152479] kjournald starting.  Commit interval 5 seconds
Jul  3 08:46:40 zumbi kernel: [   35.152522] EXT3-fs: mounted filesystem with writeback data mode.
Jul  3 08:46:40 zumbi kernel: [   35.171712] usb 6-1: new low speed USB device using uhci_hcd and address 2
Jul  3 08:46:40 zumbi kernel: [   35.314518] usb 6-1: skipped 1 descriptor after interface
Jul  3 08:46:40 zumbi kernel: [   35.319516] usb 6-1: default language 0x0409
Jul  3 08:46:40 zumbi kernel: [   35.336551] usb 6-1: New USB device found, idVendor=045e, idProduct=0083
Jul  3 08:46:40 zumbi kernel: [   35.337484] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Jul  3 08:46:40 zumbi kernel: [   35.338388] usb 6-1: Product: Basic Optical Mouse
Jul  3 08:46:40 zumbi kernel: [   35.339078] usb 6-1: Manufacturer: Microsoft
Jul  3 08:46:40 zumbi kernel: [   35.339837] usb 6-1: uevent
Jul  3 08:46:40 zumbi kernel: [   35.339846] usb 6-1: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   35.339848] usb 6-1: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   35.343517] usb 6-1: adding 6-1:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   35.343539] usb 6-1:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   35.343564] usbhid 6-1:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   35.343567] usbhid 6-1:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   35.356674] input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input3
Jul  3 08:46:40 zumbi kernel: [   35.358169] generic-usb 0003:045E:0083.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.0-1/input0
Jul  3 08:46:40 zumbi kernel: [   35.359824] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '002'
Jul  3 08:46:40 zumbi kernel: [   35.359850] uhci_hcd 0000:00:1d.0: port 2 portsc 01a3,00
Jul  3 08:46:40 zumbi kernel: [   35.359855] hub 6-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
Jul  3 08:46:40 zumbi kernel: [   35.464019] hub 6-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
Jul  3 08:46:40 zumbi kernel: [   35.565539] usb 6-2: new low speed USB device using uhci_hcd and address 3
Jul  3 08:46:40 zumbi kernel: [   35.615345] runlevel used greatest stack depth: 4360 bytes left
Jul  3 08:46:40 zumbi kernel: [   35.712433] usb 6-2: skipped 1 descriptor after interface
Jul  3 08:46:40 zumbi kernel: [   35.712437] usb 6-2: skipped 1 descriptor after interface
Jul  3 08:46:40 zumbi kernel: [   35.712441] usb 6-2: New USB device found, idVendor=0566, idProduct=3002
Jul  3 08:46:40 zumbi kernel: [   35.713333] usb 6-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Jul  3 08:46:40 zumbi kernel: [   35.714310] usb 6-2: uevent
Jul  3 08:46:40 zumbi kernel: [   35.714318] usb 6-2: usb_probe_device
Jul  3 08:46:40 zumbi kernel: [   35.714319] usb 6-2: configuration #1 chosen from 1 choice
Jul  3 08:46:40 zumbi kernel: [   35.717492] usb 6-2: adding 6-2:1.0 (config #1, interface 0)
Jul  3 08:46:40 zumbi kernel: [   35.717516] usb 6-2:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   35.717540] usbhid 6-2:1.0: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   35.717542] usbhid 6-2:1.0: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   35.730572] input: HID 0566:3002 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input4
Jul  3 08:46:40 zumbi kernel: [   35.737220] uhci_hcd 0000:00:1d.0: reserve dev 3 ep81-INT, period 8, phase 4, 118 us
Jul  3 08:46:40 zumbi kernel: [   35.737249] generic-usb 0003:0566:3002.0002: input,hidraw1: USB HID v1.10 Keyboard [HID 0566:3002] on usb-0000:00:1d.0-2/input0
Jul  3 08:46:40 zumbi kernel: [   35.738804] usb 6-2: adding 6-2:1.1 (config #1, interface 1)
Jul  3 08:46:40 zumbi kernel: [   35.738814] usb 6-2:1.1: uevent
Jul  3 08:46:40 zumbi kernel: [   35.738825] usbhid 6-2:1.1: usb_probe_interface
Jul  3 08:46:40 zumbi kernel: [   35.738826] usbhid 6-2:1.1: usb_probe_interface - got id
Jul  3 08:46:40 zumbi kernel: [   35.774482] input: HID 0566:3002 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/input/input5
Jul  3 08:46:40 zumbi kernel: [   35.775801] uhci_hcd 0000:00:1d.0: reserve dev 3 ep82-INT, period 8, phase 4, 93 us
Jul  3 08:46:40 zumbi kernel: [   35.775818] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/file.c: looking for a minor, starting at 96
Jul  3 08:46:40 zumbi kernel: [   35.775849] generic-usb 0003:0566:3002.0003: input,hiddev96,hidraw2: USB HID v1.10 Device [HID 0566:3002] on usb-0000:00:1d.0-2/input1
Jul  3 08:46:40 zumbi kernel: [   35.777490] /mnt/data/xen/vanilla/xen-unstable.hg/linux-2.6-pvops.git/drivers/usb/core/inode.c: creating file '003'
Jul  3 08:46:40 zumbi kernel: [   35.777513] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
Jul  3 08:46:40 zumbi kernel: [   35.792824] usb usb3: suspend_rh (auto-stop)
Jul  3 08:46:40 zumbi kernel: [   35.792847] usb usb4: suspend_rh (auto-stop)
Jul  3 08:46:40 zumbi kernel: [   35.792867] usb usb5: suspend_rh (auto-stop)
Jul  3 08:46:40 zumbi kernel: [   35.792887] usb usb7: suspend_rh (auto-stop)
Jul  3 08:46:40 zumbi kernel: [   35.792907] usb usb8: suspend_rh (auto-stop)
Jul  3 08:46:40 zumbi kernel: [   37.027034] hub 1-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027043] usb usb1: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027046] ehci_hcd 0000:00:1a.7: suspend root hub
Jul  3 08:46:40 zumbi kernel: [   37.027067] hub 3-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027071] usb usb3: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027073] usb usb3: suspend_rh
Jul  3 08:46:40 zumbi kernel: [   37.027088] hub 4-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027091] usb usb4: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027093] usb usb4: suspend_rh
Jul  3 08:46:40 zumbi kernel: [   37.027107] hub 5-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027110] usb usb5: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027112] usb usb5: suspend_rh
Jul  3 08:46:40 zumbi kernel: [   37.027126] hub 7-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027129] usb usb7: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027131] usb usb7: suspend_rh
Jul  3 08:46:40 zumbi kernel: [   37.027147] hub 8-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027149] usb usb8: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027150] usb usb8: suspend_rh
Jul  3 08:46:40 zumbi kernel: [   37.027163] hub 2-0:1.0: hub_suspend
Jul  3 08:46:40 zumbi kernel: [   37.027165] usb usb2: bus auto-suspend
Jul  3 08:46:40 zumbi kernel: [   37.027166] ehci_hcd 0000:00:1d.7: suspend root hub
Jul  3 08:46:40 zumbi kernel: [   39.645216] udevd version 124 started
Jul  3 08:46:40 zumbi kernel: [   39.671732] usb usb3: uevent
Jul  3 08:46:40 zumbi kernel: [   39.671754] usb 3-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.671833] usb usb4: uevent
Jul  3 08:46:40 zumbi kernel: [   39.671846] usb 4-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.671926] usb usb5: uevent
Jul  3 08:46:40 zumbi kernel: [   39.671946] usb 5-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672104] usb usb1: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672137] usb 1-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672627] usb usb6: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672640] usb 6-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672663] usb 6-1: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672676] usb 6-1:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672828] usb 6-2: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672848] usb 6-2:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.672973] usb 6-2:1.1: uevent
Jul  3 08:46:40 zumbi kernel: [   39.673217] usb usb7: uevent
Jul  3 08:46:40 zumbi kernel: [   39.673238] usb 7-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.673418] usb usb8: uevent
Jul  3 08:46:40 zumbi kernel: [   39.673450] usb 8-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   39.673618] usb usb2: uevent
Jul  3 08:46:40 zumbi kernel: [   39.673649] usb 2-0:1.0: uevent
Jul  3 08:46:40 zumbi kernel: [   40.563732] Adding 11847896k swap on /dev/sda5.  Priority:-1 extents:1 across:11847896k 
Jul  3 08:46:40 zumbi kernel: [   40.874894] EXT3 FS on sda1, internal journal
Jul  3 08:46:40 zumbi kernel: [   41.265459] tg3 0000:08:00.0: PME# disabled
Jul  3 08:46:40 zumbi kernel: [   41.354123] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jul  3 08:46:40 zumbi kernel: [   44.477154] tg3: eth0: Link is up at 1000 Mbps, full duplex.
Jul  3 08:46:40 zumbi kernel: [   44.477156] tg3: eth0: Flow control is off for TX and off for RX.
Jul  3 08:46:40 zumbi kernel: [   44.477677] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jul  3 08:46:40 zumbi kernel: [   46.939162] svc: failed to register lockdv1 RPC service (errno 97).
Jul  3 08:46:40 zumbi kernel: [   46.941181] mount.nfs used greatest stack depth: 3328 bytes left
Jul  3 08:46:40 zumbi kernel: [   48.293056] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
Jul  3 08:46:47 zumbi kernel: [   55.324471] eth0: no IPv6 routers present

[-- Attachment #3: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

RE: Xen cannot boot with pvops dom0

[Han, Weidong]

Jun Koi wrote:
> On Thu, Jun 25, 2009 at 6:20 PM, Han, Weidong<weidong.han@intel.com>
> wrote: 
>> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0
>> (commit 384a55c0). Booting will hang, following is the serial
>> console output:  
>> 
>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch
>> input to Xen ) (XEN) Freed 128kB init memory.
>> mapping kernel into physical memory
>> Xen: setup ISA identity maps
>> about to get started...
>> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
>> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
>> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
>> (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
>> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
>> (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! 
>> 
>> 
>> Did anyone meet this issue? Is there any difference on build and
>> installation between pvops dom0 and 2.6.18 dom0? Following is my
>> instructions, pls correct me if something is wrong. Appreciate in
>> advance.   
>> 
>> My build and installation instructions:
>>        - cd xen-unstable.hg
>>        - make world (linux-2.6-pvops.git will be cloned)
>>        - make install
>> 
>> My grub entry:
>>        title Xen - pvops
>>                root (hd0,2)
>>                kernel /boot/xen.gz dom0_mem=512m
>>                module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3
>> console=tty0 console=ttyS0 
>> 
>> I also tried build pvops dom0 manually as follows, but it doesn't
>> help. 
>>        - cd linux-2.6-pvops.git
>>        - make
>>        - make modules_install
>>        - make install
>> 
> 
> I am not quite sure if that is the correct way to recompile kernel, as
> sometimes I have some problems with Dom0 booting after that.
> 
> I usually recompile Dom0 kernel this way: (from the root directory)
> 
> # make linux-2.6-xen-config  (to configure kernel options)
> # make linux-2.6-xen-build
> # make linux-2.6-xen-install
> 

I also tried this way (make linux-2.6-pvops-build), the problem is still there.

> Then dont forget to "mkinitramfs", of course

Yes, I always mkinitrd for it through "mkinitrd initrd-2.6-xen.img 2.6.18.8-xen". 

It can boot with manually built pvops dom0 on my another platform, but I found xend cannot be started, there is no directory xen under /proc. That means drivers/xen are not installed, althrough they are built.

I just want to know anyone has successfully made Xen with pvops work, and can you share your instructions? Thanks.

Regards,
Weidong

> 
> Thanks,
> J

Re: Xen cannot boot with pvops dom0

[Patrick Colp]

Han, Weidong wrote:
> It can boot with manually built pvops dom0 on my another platform, but I found xend cannot be started, there is no directory xen under /proc. That means drivers/xen are not installed, althrough they are built.

Out of curiosity (and with the hope of being able to track down the 
problem, as I also suspect this a platform/cpu specific problem), what are 
the platforms you used: both the one that boots pvops and the one that doesn't?


Patrick

RE: Xen cannot boot with pvops dom0

[Han, Weidong]

Patrick Colp wrote:
> Han, Weidong wrote:
>> It can boot with manually built pvops dom0 on my another platform,
>> but I found xend cannot be started, there is no directory xen under
>> /proc. That means drivers/xen are not installed, althrough they are
>> built.   
> 
> Out of curiosity (and with the hope of being able to track down the
> problem, as I also suspect this a platform/cpu specific problem),
> what are 
> the platforms you used: both the one that boots pvops and the one
> that doesn't? 
> 

I found the boot issue on my Q35, it can boot on my Nehalem. 

Regards,
Weidong

Re: Xen cannot boot with pvops dom0

[Patrick Colp]

Han, Weidong wrote:
> Patrick Colp wrote:
>> Han, Weidong wrote:
>>> It can boot with manually built pvops dom0 on my another platform,
>>> but I found xend cannot be started, there is no directory xen under
>>> /proc. That means drivers/xen are not installed, althrough they are
>>> built.   
>> Out of curiosity (and with the hope of being able to track down the
>> problem, as I also suspect this a platform/cpu specific problem),
>> what are 
>> the platforms you used: both the one that boots pvops and the one
>> that doesn't? 
>>
> 
> I found the boot issue on my Q35, it can boot on my Nehalem. 

What are the motherboard chipsets?


Patrick

Re: Xen cannot boot with pvops dom0

[Christian Tramnitz]

Patrick Colp wrote:
>> I found the boot issue on my Q35, it can boot on my Nehalem. 
> 
> What are the motherboard chipsets?

Q35 *is* the chipset, for Nehalem its a Tylersburg chipset (either X58 
or 55x0)

Best regards,
    Christian

RE: Re: Xen cannot boot with pvops dom0

[Jiang, Yunhong]

[-- Attachment #1: Type: text/plain, Size: 1539 bytes --]

hi, all, can you try to revert following two patches to see if any help?
If it do fix the issue, I will look it tomorrow when back to office.

--jyh


changeset:   19809:16c2806b09c6
user:        Keir Fraser <keir.fraser@citrix.com>
date:        Tue Jun 23 11:11:46 2009 +0100
files:       xen/arch/x86/irq.c
description:
x86: Another assign_irq_vector() cleanup.

Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>


changeset:   19804:07fea69baadc
user:        Keir Fraser <keir.fraser@citrix.com>
date:        Fri Jun 19 08:43:58 2009 +0100
files:       xen/arch/x86/irq.c
description:
x86: Fix legacy irq allocation issue

When try to assign vector for irq, we should not assign vector for
legacy irq, which has fixed mapped irq<->vector relationship.

Signed-off-by: Jiang, Yunhong <yunhong.jiang@intel.com>
>-----Original Message-----
>From: xen-devel-bounces@lists.xensource.com 
>[mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of 
>Christian Tramnitz
>Sent: 2009年6月25日 20:09
>To: xen-devel@lists.xensource.com
>Subject: [Xen-devel] Re: Xen cannot boot with pvops dom0
>
>Patrick Colp wrote:
>>> I found the boot issue on my Q35, it can boot on my Nehalem. 
>> 
>> What are the motherboard chipsets?
>
>Q35 *is* the chipset, for Nehalem its a Tylersburg chipset (either X58 
>or 55x0)
>
>Best regards,
>    Christian
>
>
>_______________________________________________
>Xen-devel mailing list
>Xen-devel@lists.xensource.com
>http://lists.xensource.com/xen-devel
>

[-- Attachment #2: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Re: Re: Xen cannot boot with pvops dom0

[Patrick Colp]

I tried reverting those two changesets with no real effect (I got an extra error 
message from Xen to do with something about the timer).

I still have a sneaking suspicion the problem is with the Linux kernel and not 
Xen, but I could be wrong.


Patrick


Jiang, Yunhong wrote:
> hi, all, can you try to revert following two patches to see if any help?
> If it do fix the issue, I will look it tomorrow when back to office.
> 
> --jyh
> 
> 
> changeset:   19809:16c2806b09c6
> user:        Keir Fraser <keir.fraser@citrix.com>
> date:        Tue Jun 23 11:11:46 2009 +0100
> files:       xen/arch/x86/irq.c
> description:
> x86: Another assign_irq_vector() cleanup.
> 
> Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
> 
> 
> changeset:   19804:07fea69baadc
> user:        Keir Fraser <keir.fraser@citrix.com>
> date:        Fri Jun 19 08:43:58 2009 +0100
> files:       xen/arch/x86/irq.c
> description:
> x86: Fix legacy irq allocation issue
> 
> When try to assign vector for irq, we should not assign vector for
> legacy irq, which has fixed mapped irq<->vector relationship.
> 
> Signed-off-by: Jiang, Yunhong <yunhong.jiang@intel.com>
>> -----Original Message-----
>> From: xen-devel-bounces@lists.xensource.com 
>> [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of 
>> Christian Tramnitz
>> Sent: 2009年6月25日 20:09
>> To: xen-devel@lists.xensource.com
>> Subject: [Xen-devel] Re: Xen cannot boot with pvops dom0
>>
>> Patrick Colp wrote:
>>>> I found the boot issue on my Q35, it can boot on my Nehalem. 
>>> What are the motherboard chipsets?
>> Q35 *is* the chipset, for Nehalem its a Tylersburg chipset (either X58 
>> or 55x0)
>>
>> Best regards,
>>    Christian
>>
>>
>> _______________________________________________
>> Xen-devel mailing list
>> Xen-devel@lists.xensource.com
>> http://lists.xensource.com/xen-devel
>>
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel

RE: Re: Xen cannot boot with pvops dom0

[Jiang, Yunhong]

[-- Attachment #1: Type: text/plain, Size: 3342 bytes --]

I think detailed output of dmesg (both xen and dom0) will be helpful.

I checked  the log again, and noticed following output. Seems there is IRQ source override for timer in the platform and dom0/xen have different idea of timer source in check_timer().

>> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
>> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0

Thanks
Yunhong Jiang

>-----Original Message-----
>From: Patrick Colp [mailto:Patrick.Colp@citrix.com] 
>Sent: 2009年6月26日 17:38
>To: Jiang, Yunhong
>Cc: Christian Tramnitz; xen-devel@lists.xensource.com
>Subject: Re: [Xen-devel] Re: Xen cannot boot with pvops dom0
>
>I tried reverting those two changesets with no real effect (I 
>got an extra error 
>message from Xen to do with something about the timer).
>
>I still have a sneaking suspicion the problem is with the 
>Linux kernel and not 
>Xen, but I could be wrong.
>
>
>Patrick
>
>
>Jiang, Yunhong wrote:
>> hi, all, can you try to revert following two patches to see 
>if any help?
>> If it do fix the issue, I will look it tomorrow when back to office.
>> 
>> --jyh
>> 
>> 
>> changeset:   19809:16c2806b09c6
>> user:        Keir Fraser <keir.fraser@citrix.com>
>> date:        Tue Jun 23 11:11:46 2009 +0100
>> files:       xen/arch/x86/irq.c
>> description:
>> x86: Another assign_irq_vector() cleanup.
>> 
>> Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
>> 
>> 
>> changeset:   19804:07fea69baadc
>> user:        Keir Fraser <keir.fraser@citrix.com>
>> date:        Fri Jun 19 08:43:58 2009 +0100
>> files:       xen/arch/x86/irq.c
>> description:
>> x86: Fix legacy irq allocation issue
>> 
>> When try to assign vector for irq, we should not assign vector for
>> legacy irq, which has fixed mapped irq<->vector relationship.
>> 
>> Signed-off-by: Jiang, Yunhong <yunhong.jiang@intel.com>
>>> -----Original Message-----
>>> From: xen-devel-bounces@lists.xensource.com 
>>> [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of 
>>> Christian Tramnitz
>>> Sent: 2009年6月25日 20:09
>>> To: xen-devel@lists.xensource.com
>>> Subject: [Xen-devel] Re: Xen cannot boot with pvops dom0
>>>
>>> Patrick Colp wrote:
>>>>> I found the boot issue on my Q35, it can boot on my Nehalem. 
>>>> What are the motherboard chipsets?
>>> Q35 *is* the chipset, for Nehalem its a Tylersburg chipset 
>(either X58 
>>> or 55x0)
>>>
>>> Best regards,
>>>    Christian
>>>
>>>
>>> _______________________________________________
>>> Xen-devel mailing list
>>> Xen-devel@lists.xensource.com
>>> http://lists.xensource.com/xen-devel
>>>
>> 
>> 
>> 
>---------------------------------------------------------------
>---------
>> 
>> _______________________________________________
>> Xen-devel mailing list
>> Xen-devel@lists.xensource.com
>> http://lists.xensource.com/xen-devel
>

[-- Attachment #2: Type: text/plain, Size: 138 bytes --]

_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel

Re: Xen cannot boot with pvops dom0

[Jeremy Fitzhardinge]

On 06/25/09 02:20, Han, Weidong wrote:
> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0 (commit 384a55c0). Booting will hang, following is the serial console output: 
>
> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
> )
> (XEN) Freed 128kB init memory.
> mapping kernel into physical memory
> Xen: setup ISA identity maps
> about to get started...
> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
> (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
> (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
> (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>   

The ioapic_guest_write messages are just noise, and have no bearing on
the problem.  Are there no more messages from the kernel after "about to
get started"?  The ioapic messages at least tell us it is getting quite
a distance into the boot and discovering devices.

> Did anyone meet this issue? Is there any difference on build and installation between pvops dom0 and 2.6.18 dom0? Following is my instructions, pls correct me if something is wrong. Appreciate in advance.
>  
> My build and installation instructions:
> 	- cd xen-unstable.hg
> 	- make world (linux-2.6-pvops.git will be cloned)
> 	- make install
>
> My grub entry:
> 	title Xen - pvops
>     		root (hd0,2)
>     		kernel /boot/xen.gz dom0_mem=512m
>     		module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3 console=tty0 console=ttyS0
>   

What happens if you have "console=hvc0 earlyprintk=xen ignore_loglevel"
on the "module" line?  You should get more output from the kernel.  You
might also want "console=com1,vga" on the Xen line.

    J

RE: Xen cannot boot with pvops dom0

[Han, Weidong]

Jeremy Fitzhardinge wrote:
> On 06/25/09 02:20, Han, Weidong wrote:
>> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0
>> (commit 384a55c0). Booting will hang, following is the serial
>> console output:  
>> 
>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch
>> input to Xen ) (XEN) Freed 128kB init memory.
>> mapping kernel into physical memory
>> Xen: setup ISA identity maps
>> about to get started...
>> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
>> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
>> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
>> (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
>> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
>> (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>> IRQ! 
>> 
> 
> The ioapic_guest_write messages are just noise, and have no bearing on
> the problem.  Are there no more messages from the kernel after "about
> to get started"?  The ioapic messages at least tell us it is getting
> quite a distance into the boot and discovering devices.

Actually, pv-ops dom0 boot successfully. I remotely access my machine via serial console. Normally after dom0 boot, it display "login:" line. But serial console stops at ioapic_guest_write messages when boot pv_ops, I thought it's hung. 

But I found xend still cannot be started. I got the following messages when I start it:

[root@vt-randy ~]# xend start
ERROR Internal error: Could not obtain handle on privileged command interface (2 = No such file or directory)
Traceback (most recent call last):
  File "/usr/sbin/xend", line 36, in ?
    from xen.xend.server import SrvDaemon
  File "usr/lib64/python2.4/site-packages/xen/xend/server/SrvDaemon.py", line 26, in ?
  File "usr/lib64/python2.4/site-packages/xen/xend/server/relocate.py", line 28, in ?
  File "usr/lib64/python2.4/site-packages/xen/xend/XendDomain.py", line 35, in ?
  File "usr/lib64/python2.4/site-packages/xen/xend/XendCheckpoint.py", line 20, in ?
  File "usr/lib64/python2.4/site-packages/xen/xend/image.py", line 46, in ?
xen.lowlevel.xc.Error: (1, 'Internal error', 'Could not obtain handle on privileged command interface (2 = No such file or directory)')


> 
>> Did anyone meet this issue? Is there any difference on build and
>> installation between pvops dom0 and 2.6.18 dom0? Following is my
>> instructions, pls correct me if something is wrong. Appreciate in
>> advance.   
>> 
>> My build and installation instructions:
>> 	- cd xen-unstable.hg
>> 	- make world (linux-2.6-pvops.git will be cloned)
>> 	- make install
>> 
>> My grub entry:
>> 	title Xen - pvops
>>     		root (hd0,2)
>>     		kernel /boot/xen.gz dom0_mem=512m
>>     		module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3
>> console=tty0 console=ttyS0 
>> 
> 
> What happens if you have "console=hvc0 earlyprintk=xen
> ignore_loglevel" on the "module" line?  You should get more output
> from the kernel.  You might also want "console=com1,vga" on the Xen
> line. 
> 
>     J

Re: Xen cannot boot with pvops dom0

[Thomas DuBuisson]

For what its worth, I've recently had significant issues building a
good pvops Dom0 kernel.  At first it wouldn't boot (kernel oops) then
it had an odd permission issue with /dev/pts/* that stopped xterm/bash
from working.

I went through the mud and found a configuration [1] that avoids
whatever issues I was hitting.  I thought about running a diff against
this and whatever the default was, but there would be lots of noise
due to many preference-specific changes (ex: built in all options
specifically matching my hardware).

Tom

[1] http://web.cecs.pdx.edu/~dubuisst/pvops_dom0.config

On Tue, Jun 30, 2009 at 7:43 PM, Han, Weidong<weidong.han@intel.com> wrote:
> Jeremy Fitzhardinge wrote:
>> On 06/25/09 02:20, Han, Weidong wrote:
>>> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0
>>> (commit 384a55c0). Booting will hang, following is the serial
>>> console output:
>>>
>>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch
>>> input to Xen ) (XEN) Freed 128kB init memory.
>>> mapping kernel into physical memory
>>> Xen: setup ISA identity maps
>>> about to get started...
>>> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
>>> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
>>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
>>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
>>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
>>> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
>>> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
>>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
>>> (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
>>> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
>>> (XEN) ioapic_guest_write: old_entry=0000a921, new_entry=0001a921
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ!
>>>
>>
>> The ioapic_guest_write messages are just noise, and have no bearing on
>> the problem.  Are there no more messages from the kernel after "about
>> to get started"?  The ioapic messages at least tell us it is getting
>> quite a distance into the boot and discovering devices.
>
> Actually, pv-ops dom0 boot successfully. I remotely access my machine via serial console. Normally after dom0 boot, it display "login:" line. But serial console stops at ioapic_guest_write messages when boot pv_ops, I thought it's hung.
>
> But I found xend still cannot be started. I got the following messages when I start it:
>
> [root@vt-randy ~]# xend start
> ERROR Internal error: Could not obtain handle on privileged command interface (2 = No such file or directory)
> Traceback (most recent call last):
>  File "/usr/sbin/xend", line 36, in ?
>    from xen.xend.server import SrvDaemon
>  File "usr/lib64/python2.4/site-packages/xen/xend/server/SrvDaemon.py", line 26, in ?
>  File "usr/lib64/python2.4/site-packages/xen/xend/server/relocate.py", line 28, in ?
>  File "usr/lib64/python2.4/site-packages/xen/xend/XendDomain.py", line 35, in ?
>  File "usr/lib64/python2.4/site-packages/xen/xend/XendCheckpoint.py", line 20, in ?
>  File "usr/lib64/python2.4/site-packages/xen/xend/image.py", line 46, in ?
> xen.lowlevel.xc.Error: (1, 'Internal error', 'Could not obtain handle on privileged command interface (2 = No such file or directory)')
>
>
>>
>>> Did anyone meet this issue? Is there any difference on build and
>>> installation between pvops dom0 and 2.6.18 dom0? Following is my
>>> instructions, pls correct me if something is wrong. Appreciate in
>>> advance.
>>>
>>> My build and installation instructions:
>>>      - cd xen-unstable.hg
>>>      - make world (linux-2.6-pvops.git will be cloned)
>>>      - make install
>>>
>>> My grub entry:
>>>      title Xen - pvops
>>>              root (hd0,2)
>>>              kernel /boot/xen.gz dom0_mem=512m
>>>              module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3
>>> console=tty0 console=ttyS0
>>>
>>
>> What happens if you have "console=hvc0 earlyprintk=xen
>> ignore_loglevel" on the "module" line?  You should get more output
>> from the kernel.  You might also want "console=com1,vga" on the Xen
>> line.
>>
>>     J
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>

RE: Xen cannot boot with pvops dom0

[Han, Weidong]

Han, Weidong wrote:
> Jeremy Fitzhardinge wrote:
>> On 06/25/09 02:20, Han, Weidong wrote:
>>> I tried with latest Xen unstable (c/s 19833) with latest pvops dom0
>>> (commit 384a55c0). Booting will hang, following is the serial
>>> console output: 
>>> 
>>> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch
>>> input to Xen ) (XEN) Freed 128kB init memory.
>>> mapping kernel into physical memory
>>> Xen: setup ISA identity maps
>>> about to get started...
>>> (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
>>> (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
>>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1
>>> (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900
>>> (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
>>> (XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
>>> (XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
>>> (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
>>> (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19,
>>> new_irq=19 (XEN) ioapic_guest_write: old_entry=0000a9c0,
>>> new_entry=0001a9c0 (XEN) ioapic_guest_write: Attempt to modify
>>> IO-APIC pin for in-use IRQ! (XEN) ioapic_guest_write: apic=0,
>>> pin=23, old_irq=23, new_irq=23 (XEN) ioapic_guest_write:
>>> old_entry=0000a9d0, new_entry=0001a9d0 (XEN) ioapic_guest_write:
>>> Attempt to modify IO-APIC pin for in-use IRQ! (XEN)
>>> ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19 (XEN)
>>> ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0 (XEN)
>>> ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>>> (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
>>> (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
>>> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use
>>> IRQ! (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18,
>>> new_irq=18 (XEN) ioapic_guest_write: old_entry=0000a921,
>>> new_entry=0001a921 (XEN) ioapic_guest_write: Attempt to modify
>>> IO-APIC pin for in-use IRQ!  
>>> 
>> 
>> The ioapic_guest_write messages are just noise, and have no bearing
>> on the problem.  Are there no more messages from the kernel after
>> "about to get started"?  The ioapic messages at least tell us it is
>> getting quite a distance into the boot and discovering devices.
> 
> Actually, pv-ops dom0 boot successfully. I remotely access my machine
> via serial console. Normally after dom0 boot, it display "login:"
> line. But serial console stops at ioapic_guest_write messages when
> boot pv_ops, I thought it's hung.   
> 
> But I found xend still cannot be started. I got the following
> messages when I start it: 
> 
> [root@vt-randy ~]# xend start
> ERROR Internal error: Could not obtain handle on privileged command
> interface (2 = No such file or directory) 
> Traceback (most recent call last):
>   File "/usr/sbin/xend", line 36, in ?
>     from xen.xend.server import SrvDaemon
>   File
>   "usr/lib64/python2.4/site-packages/xen/xend/server/SrvDaemon.py",
>   line 26, in ? File
>   "usr/lib64/python2.4/site-packages/xen/xend/server/relocate.py",
>   line 28, in ? File
> "usr/lib64/python2.4/site-packages/xen/xend/XendDomain.py", line 35,
> in ? File
> "usr/lib64/python2.4/site-packages/xen/xend/XendCheckpoint.py", line
> 20, in ? File "usr/lib64/python2.4/site-packages/xen/xend/image.py",
> line 46, in ?     
> xen.lowlevel.xc.Error: (1, 'Internal error', 'Could not obtain handle
> on privileged command interface (2 = No such file or directory)') 
> 

After reading pv_ops wiki (http://wiki.xensource.com/xenwiki/XenParavirtOps), I solved it. It requires to add a line to /etc/fstab: none /proc/xen xenfs defaults 0 0.

Now pv_ops dom0 works for me. Thanks.

Regards,
Weidong

> 
>> 
>>> Did anyone meet this issue? Is there any difference on build and
>>> installation between pvops dom0 and 2.6.18 dom0? Following is my
>>> instructions, pls correct me if something is wrong. Appreciate in
>>> advance. 
>>> 
>>> My build and installation instructions:
>>> 	- cd xen-unstable.hg
>>> 	- make world (linux-2.6-pvops.git will be cloned)
>>> 	- make install
>>> 
>>> My grub entry:
>>> 	title Xen - pvops
>>>     		root (hd0,2)
>>>     		kernel /boot/xen.gz dom0_mem=512m
>>>     		module /boot/vmlinuz-2.6-30.rc3-tip ro root=/dev/sda3
>>> console=tty0 console=ttyS0 
>>> 
>> 
>> What happens if you have "console=hvc0 earlyprintk=xen
>> ignore_loglevel" on the "module" line?  You should get more output
>> from the kernel.  You might also want "console=com1,vga" on the Xen
>> line. 
>> 
>>     J

Re: Xen cannot boot with pvops dom0

[Jeremy Fitzhardinge]

On 06/30/09 22:29, Han, Weidong wrote:
> After reading pv_ops wiki (http://wiki.xensource.com/xenwiki/XenParavirtOps), I solved it. It requires to add a line to /etc/fstab: none /proc/xen xenfs defaults 0 0.
>
> Now pv_ops dom0 works for me. Thanks.
>   

Good, thanks for letting me know.

    J