Re: [PATCH net-next-2.6] bnx2: Update vlan_features

[Eric Dumazet <eric.dumazet@gmail.com>]

Eric Dumazet a écrit :
> Or Gerlitz a écrit :
>> Eric Dumazet wrote:
>>> Jay Vosburgh a écrit :
>>>> Propogate the vlan_features of the slave devices to the bonding
>>>> master device, using the same logic as for regular features.
>>> Seems pretty cool, but I could not test it on my dev machine, since
>>> tg3 and bnx2 drivers dont advertize yet vlan_features
>> The bnx2x maintainer posted yesterday a patch that does so, I assume a
>> similar patch could work for at least one of tg3 or bnx2. I copied both
>> maintainers on this email, in  the hope they can come up with a patch.
>>
> 
> Here is the bnx2 patch I cooked to test this vlan_features propagation on bonding.
> 
> Everything fine so far !
> 
> # cat /proc/net/bonding/bond0
> Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
> 
> Bonding Mode: fault-tolerance (active-backup)
> Primary Slave: None
> Currently Active Slave: eth1
> MII Status: up
> MII Polling Interval (ms): 100
> Up Delay (ms): 0
> Down Delay (ms): 0
> 
> Slave Interface: eth1    (bnx2 driver)
> MII Status: up
> Link Failure Count: 2
> Permanent HW addr: 00:1e:0b:ec:d3:d2
> 
> Slave Interface: eth2    (tg3 driver)
> MII Status: up
> Link Failure Count: 0
> Permanent HW addr: 00:1e:0b:92:78:50
> 
> 
> # ethtool -k bond0
> Offload parameters for bond0:
> Cannot get device rx csum settings: Operation not supported
> rx-checksumming: off
> tx-checksumming: on
> scatter-gather: on
> tcp-segmentation-offload: on
> udp-fragmentation-offload: off
> generic-segmentation-offload: off
> generic-receive-offload: off
> large-receive-offload: off
> 
> # ip link add link bond0 vlan.103 type vlan id 103
> # ethtool -k vlan.103
> Offload parameters for vlan.103:
> rx-checksumming: off
> tx-checksumming: on
> scatter-gather: on
> tcp-segmentation-offload: on
> udp-fragmentation-offload: off
> generic-segmentation-offload: on
> generic-receive-offload: off
> large-receive-offload: off
> 
> 
> Thanks Or & Jay
> 

Updated to take into account Patrick feedback : We dont need to
change vlan_features in bnx2_set_tso()

Quoting Patrick from another thread :
  "vlan_features doesn't need to be updated, the resulting dev->features
  of the VLAN device is computed as the intersection of dev->features
  and dev->vlan_features."

[PATCH net-next-2.6] bnx2: Update vlan_features

In order to get full use of some advanced features of BNX2, we now need to
fill dev->vlan_features.

Patch successfully tested with vlan devices built on top of bonding.
(bond0 : one bnx2 slave, one tg3 slave (not yet vlan_features enabled)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
---
 drivers/net/bnx2.c |   19 +++++++++++++++----
 1 files changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index b70cc99..cec1b17 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -8023,6 +8023,13 @@ static const struct net_device_ops bnx2_netdev_ops = {
 #endif
 };
 
+static void inline vlan_features_add(struct net_device *dev, unsigned long flags)
+{
+#ifdef BCM_VLAN
+	dev->vlan_features |= flags;
+#endif
+}
+
 static int __devinit
 bnx2_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
@@ -8064,16 +8071,20 @@ bnx2_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	memcpy(dev->perm_addr, bp->mac_addr, 6);
 
 	dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
-	if (CHIP_NUM(bp) == CHIP_NUM_5709)
+	vlan_features_add(dev, NETIF_F_IP_CSUM | NETIF_F_SG);
+	if (CHIP_NUM(bp) == CHIP_NUM_5709) {
 		dev->features |= NETIF_F_IPV6_CSUM;
-
+		vlan_features_add(dev, NETIF_F_IPV6_CSUM);
+	}
 #ifdef BCM_VLAN
 	dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
 #endif
 	dev->features |= NETIF_F_TSO | NETIF_F_TSO_ECN;
-	if (CHIP_NUM(bp) == CHIP_NUM_5709)
+	vlan_features_add(dev, NETIF_F_TSO | NETIF_F_TSO_ECN);
+	if (CHIP_NUM(bp) == CHIP_NUM_5709) {
 		dev->features |= NETIF_F_TSO6;
-
+		vlan_features_add(dev, NETIF_F_TSO6);
+	}
 	if ((rc = register_netdev(dev))) {
 		dev_err(&pdev->dev, "Cannot register net device\n");
 		goto error;