No graphic when loading "x11-gpe-image"

No graphic when loading "x11-gpe-image"

[Ulf Samuelsson]

I have tried opie-image which boots properly and I get a screen

x11-gpe-image does not start properly.
Only a black screen.

Anyone gotten this to work with a late git?

-- 
Best Regards
Ulf Samuelsson

Re: No graphic when loading "x11-gpe-image"

[Koen Kooi]

On 14-08-09 09:48, Ulf Samuelsson wrote:
> I have tried opie-image which boots properly and I get a screen
>
> x11-gpe-image does not start properly.
> Only a black screen.

My crystal ball is broken, without some log files or output we can't 
help you

Re: No graphic when loading "x11-gpe-image"

[Ulf Samuelsson]

Koen Kooi skrev:
> On 14-08-09 09:48, Ulf Samuelsson wrote:
>> I have tried opie-image which boots properly and I get a screen
>>
>> x11-gpe-image does not start properly.
>> Only a black screen.
> 
> My crystal ball is broken, without some log files or output we can't
> help you
> 
> 
There is really no output

gpe_dm is started and then nothing happens.


I can use mplayer to play a video, but
I do not get the X-Environment.
opie-image uses the same kernel settings and this boots OK
with the right environment.

Anyone got a working ARM926EJ-S jffs2 image I can test on?


> *** AT91Bootstrap-2.13-rc1
> AT45DB642D detected
> Valid image found
> From: [0x00008400] To:        [0x23F00000] Size:      [0x00040000]
> ........SUCCESS
> Start:        [0x23F00000]

U-Boot 2009.08-rc2 (Aug 13 2009 - 08:57:38)

DRAM:  64 MB
NAND:  256 MiB
DataFlash:AT45DB642
Nb pages:   8192
Page Size:   1056
Size= 8650752 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C00041FF (RO) Bootstrap
Area 1: C0004200 to C00083FF      Environment
Area 2: C0008400 to C0041FFF (RO) U-Boot
Area 3: C0084000 to C0293FFF      Kernel
Area 4: C0294000 to C083FFFF      FS
Net:   macb0
macb0: Starting autonegotiation...
macb0: Autonegotiation complete
macb0: link up, 100Mbps full-duplex (lpa: 0xc5e1)
Hit any key to stop autoboot:  0
Saving Environment to dataflash...
## Booting kernel from Legacy Image at 21000000 ...
   Image Name:   Angstrom/2.6.30.2/at91sam9263dfc
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2072200 Bytes =  2 MB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing
Linux......................................................................................................................................
done, booting the kernel.
[    0.000000] Linux version 2.6.30.2 (ulf@grond) (gcc version 4.3.3
(GCC) ) #1 PREEMPT Fri Aug 14 00:23:38 CEST 2009
[    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ),
cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Atmel AT91SAM9263-EK
[    0.000000] Ignoring unrecognised tag 0x54410008
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Clocks: CPU 199 MHz, master 99 MHz, main 16.367 MHz
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[    0.000000] Kernel command line: root=/dev/mtdblock1 rootfstype=jffs2
ip=10.175.196.18:10.175.196.247:10.175.196.1:255.255.255.0
console=ttyS0,115200,mem=64M
[    0.000000] NR_IRQS:192
[    0.000000] AT91: 160 gpio irqs in 5 banks
[    0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.080000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[    0.090000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.100000] Memory: 64MB = 64MB total
[    0.110000] Memory: 60372KB available (3744K code, 492K data, 136K
init, 0K highmem)
[    0.120000] Calibrating delay loop... 99.53 BogoMIPS (lpj=497664)
[    0.310000] Security Framework initialized
[    0.310000] Mount-cache hash table entries: 512
[    0.320000] CPU: Testing write buffer coherency: ok
[    0.340000] net_namespace: 764 bytes
[    0.350000] NET: Registered protocol family 16
[    0.380000] AT91: Power Management
[    0.390000] AT91: Starting after user reset
[    0.450000] bio: create slab <bio-0> at 0
[    0.460000] SCSI subsystem initialized
[    0.470000] usbcore: registered new interface driver usbfs
[    0.470000] usbcore: registered new interface driver hub
[    0.480000] usbcore: registered new device driver usb
[    0.510000] NET: Registered protocol family 2
[    0.510000] IP route cache hash table entries: 1024 (order: 0, 4096
bytes)
[    0.520000] TCP established hash table entries: 2048 (order: 2, 16384
bytes)
[    0.530000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.530000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.540000] TCP reno registered
[    0.550000] NET: Registered protocol family 1
[    0.560000] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat,
Inc.
[    0.570000] msgmni has been set to 118
[    0.590000] alg: No test for stdrng (krng)
[    0.590000] io scheduler noop registered
[    0.600000] io scheduler cfq registered (default)
[    0.610000] atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at
239c0000 (mapped at ffc00000)
[    0.700000] Console: switching to colour frame buffer device 30x40
[    0.710000] atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00700000
(mapped at c48d6000), irq 26
[    0.900000] atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a
ATMEL_SERIAL
[    0.900000] atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a
ATMEL_SERIAL
[    0.940000] loop: module loaded
[    0.950000] Driver 'sd' needs updating - please use bus_type methods
[    0.960000] MACB_mii_bus: probed
[    0.970000] eth0: Atmel MACB at 0xfffbc000 irq 21 (04:25:fe:ed:00:18)
[    0.970000] eth0: attached PHY driver [Davicom DM9161A]
(mii_bus:phy_addr=ffffffff:00, irq=-1)
[    1.000000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda
(Samsung NAND 256MiB 3,3V 8-bit)
[    1.010000] AT91 NAND: 8-bit, Software ECC
[    1.020000] Scanning device for bad blocks
[    1.100000] Creating 3 MTD partitions on "atmel_nand":
[    1.110000] 0x000000000000-0x000000400000 : "Bootstrap"
[    1.120000] 0x000000400000-0x000008000000 : "Root File System"
[    1.130000] 0x000008000000-0x000010000000 : "Data"
[    1.140000] atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000
(irq 14)
[    1.150000] mtd_dataflash spi0.0: AT45DB642x (8448 KBytes) pagesize
1056 bytes (OTP)
[    1.170000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.180000] at91_ohci at91_ohci: AT91 OHCI
[    1.190000] at91_ohci at91_ohci: new USB bus registered, assigned bus
number 1
[    1.190000] at91_ohci at91_ohci: irq 29, io mem 0x00a00000
[    1.260000] usb usb1: configuration #1 chosen from 1 choice
[    1.270000] hub 1-0:1.0: USB hub found
[    1.270000] hub 1-0:1.0: 2 ports detected
[    1.280000] Initializing USB Mass Storage driver...
[    1.290000] usbcore: registered new interface driver usb-storage
[    1.290000] USB Mass Storage support registered.
[    1.300000] mice: PS/2 mouse device common for all mice
[    1.310000] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    1.320000] ads7846 spi0.3: touchscreen, irq 31
[    1.320000] input: ADS784x Touchscreen as
/devices/platform/atmel_spi.0/spi0.3/input/input1
[    1.340000] rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as
rtc0
[    1.350000] IRQ 1/rtc0: IRQF_DISABLED is not guaranteed on shared IRQs
[    1.350000] i2c /dev entries driver
[    1.360000] at24 0-0050: 65536 byte 24c512 EEPROM (writable)
[    1.370000] i2c-gpio i2c-gpio: using pins 68 (SDA) and 69 (SCL)
[    1.380000] AT91SAM9 Watchdog: sorry, watchdog is disabled
[    1.380000] at91_wdt: probe of at91_wdt failed with error -5
[    1.390000] cpuidle: using governor ladder
[    1.390000] cpuidle: using governor menu
[    1.400000] Registered led device: ds1
[    1.410000] Registered led device: ds2
[    1.410000] Registered led device: ds3
[    1.450000] usbcore: registered new interface driver usbhid
[    1.450000] usbhid: v2.6:USB HID core driver
[    1.460000] Advanced Linux Sound Architecture Driver Version 1.0.20.
[    1.470000] AC97C regs = FFFA0000
[    1.470000] AC97C irq  = 18
[    1.480000] at91-ac97: codec write timeout
<4>at91-ac97: codec write timeout
<4>at91-ac97: codec write timeout
<4>at91-ac97: codec write timeout
<6>ALSA device list:
[    1.530000]   #0: Atmel AC97 Controller at 0xfffa0000, irq 18
[    1.540000] TCP cubic registered
[    1.540000] NET: Registered protocol family 17
[    1.540000] RPC: Registered udp transport module.
[    1.550000] RPC: Registered tcp transport module.
[    1.560000] rtc-at91sam9 at91_rtt.0: setting system clock to
2009-08-14 00:40:40 UTC (1250210440)
[    1.650000] usb 1-1: new full speed USB device using at91_ohci and
address 2
[    1.830000] usb 1-1: configuration #1 chosen from 1 choice
[    1.840000] scsi0 : SCSI emulation for USB Mass Storage devices
[    3.090000] IP-Config: Complete:
[    3.090000]      device=eth0, addr=10.175.196.18, mask=255.255.255.0,
gw=10.175.196.1,
[    3.100000]      host=10.175.196.18, domain=, nis-domain=(none),
[    3.100000]      bootserver=10.175.196.247,
rootserver=10.175.196.247, rootpath=
[   13.450000] eth0: link up (100/Full)
[   13.450000] VFS: Mounted root (jffs2 filesystem) on device 31:1.
[   13.460000] Freeing init memory: 136K
[   13.470000] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 2.0
1.00 PQ: 0 ANSI: 2
[   13.570000] sd 0:0:0:0: [sda] 31309760 512-byte hardware sectors:
(16.0 GB/14.9 GiB)
[   13.580000] sd 0:0:0:0: [sda] Write Protect is off
[   13.580000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   13.620000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   13.630000]  sda: sda1
[   13.650000] sd 0:0:0:0: [sda] Attached SCSI removable disk
INIT: version 2.86 booting
Please wait: booting...
Starting udev[   20.340000] udev: starting version 141

Remounting root file system...
[   28.600000] udc: at91_udc version 3 May 2006
[   28.700000] g_serial gadget: Gadget Serial v2.4
[   28.730000] g_serial gadget: g_serial ready
[   29.140000] Bluetooth: Core ver 2.15
[   29.170000] NET: Registered protocol family 31
[   29.170000] Bluetooth: HCI device and connection manager initialized
[   29.180000] Bluetooth: HCI socket layer initialized
[   29.570000] Bluetooth: L2CAP ver 2.13
[   29.570000] Bluetooth: L2CAP socket layer initialized
[   29.710000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   31.020000] NET: Registered protocol family 10
[   31.340000] Bluetooth: RFCOMM socket layer initialized
[   31.340000] Bluetooth: RFCOMM TTY layer initialized
[   31.350000] Bluetooth: RFCOMM ver 1.11
ALSA: Restoring mixer settings...
Configuring network interfaces... [   34.450000] eth0: link down
[   35.250000] ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0      no wireless extensions.

udhcpc (v1.13.2) started
run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1
Sending discover...
[   37.450000] eth0: link up (100/Full)
[   37.450000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 10.175.196.237...
Lease of 10.175.196.237 obtained, lease time 86400
run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1
adding dns 10.175.196.1
done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Hardware abstraction layer hald
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting music player daemon: mpdlog: problem opening log file
"/var/lib/mpd/mpd.log" (config line 33) for writing
Aborted
.
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
* starting FTP Server: vsftpd... done.
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Running ntpdate to synchronize clock.
Starting GPE display manager: gpe-dm

.-------.
|       |                  .-.
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution at91sam9263dfc ttyS0

Angstrom 2009.X-test-20090813 at91sam9263dfc ttyS0

at91sam9263dfc login: root
root@at91sam9263dfc:~#
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel


-- 
Best Regards
Ulf Samuelsson

Re: No graphic when loading "x11-gpe-image"

[Phil Blundell]

On Fri, 2009-08-14 at 17:25 +0200, Ulf Samuelsson wrote:
> There is really no output
> 
> gpe_dm is started and then nothing happens.

Do you see anything in syslog?  What does the output of "ps" look like
when it's in this state?

p.

Re: No graphic when loading "x11-gpe-image"

[Ulf Samuelsson]

Phil Blundell skrev:
> On Fri, 2009-08-14 at 17:25 +0200, Ulf Samuelsson wrote:
>> There is really no output
>>
>> gpe_dm is started and then nothing happens.
> 
> Do you see anything in syslog?  What does the output of "ps" look like
> when it's in this state?
> 
> p.
> 
> 

I reloaded another board with X11-image right now
and did gpe-dm -n, which tells me I have no ${DISPLAY}
It is ":0", which is no good.

Looked at the obvious place and yes, /etc/X11/xorg.conf is empty...
Should this be generated by OpenEmbedded? Where?

The full command line is:
exec Xorg -br -pn  -dpi 100 -rgba bgr -screen 240x320 :0 -noreset

It complains about an unrecognized option "-rgba"
(The AT91SAM9263 should use BGRI anyway...)




> 
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel


-- 
Best Regards
Ulf Samuelsson

Re: No graphic when loading "x11-gpe-image"

[Graeme Gregory]

Ulf Samuelsson wrote:
> Phil Blundell skrev:
>   
>> On Fri, 2009-08-14 at 17:25 +0200, Ulf Samuelsson wrote:
>>     
>>> There is really no output
>>>
>>> gpe_dm is started and then nothing happens.
>>>       
>> Do you see anything in syslog?  What does the output of "ps" look like
>> when it's in this state?
>>
>> p.
>>
>>
>>     
>
> I reloaded another board with X11-image right now
> and did gpe-dm -n, which tells me I have no ${DISPLAY}
> It is ":0", which is no good.
>
> Looked at the obvious place and yes, /etc/X11/xorg.conf is empty...
> Should this be generated by OpenEmbedded? Where?
>
> The full command line is:
> exec Xorg -br -pn  -dpi 100 -rgba bgr -screen 240x320 :0 -noreset
>
> It complains about an unrecognized option "-rgba"
> (The AT91SAM9263 should use BGRI anyway...)
>
>   
xorg.conf is allowed to be empty, in most simple cases Xorg can work out 
its configuration itself. I suspect you have found the problem yourself 
is -rgba is not recognised and stopping the xserver starting.

Look at the xserver-common or xserver-kdrive-common packages for the X 
startup files I lost track of which distro uses which package.

Graeme

Re: No graphic when loading "x11-gpe-image"

[Phil Blundell]

On Fri, 2009-08-14 at 22:01 +0200, Ulf Samuelsson wrote:
> The full command line is:
> exec Xorg -br -pn  -dpi 100 -rgba bgr -screen 240x320 :0 -noreset
> 
> It complains about an unrecognized option "-rgba"

Yeah, that looks like the startup scripts are trying to pass kdrive
options to Xorg.  I guess you need to either install kdrive, or patch
the scripts to do the right thing for Xorg.

p.

Re: No graphic when loading "x11-gpe-image"

[Ulf Samuelsson]

Graeme Gregory skrev:
> Ulf Samuelsson wrote:
>> Phil Blundell skrev:
>>  
>>> On Fri, 2009-08-14 at 17:25 +0200, Ulf Samuelsson wrote:
>>>    
>>>> There is really no output
>>>>
>>>> gpe_dm is started and then nothing happens.
>>>>       
>>> Do you see anything in syslog?  What does the output of "ps" look like
>>> when it's in this state?
>>>
>>> p.
>>>
>>>
>>>     
>>
>> I reloaded another board with X11-image right now
>> and did gpe-dm -n, which tells me I have no ${DISPLAY}
>> It is ":0", which is no good.
>>
>> Looked at the obvious place and yes, /etc/X11/xorg.conf is empty...
>> Should this be generated by OpenEmbedded? Where?
>>
>> The full command line is:
>> exec Xorg -br -pn  -dpi 100 -rgba bgr -screen 240x320 :0 -noreset
>>
>> It complains about an unrecognized option "-rgba"
>> (The AT91SAM9263 should use BGRI anyway...)
>>
>>   
> xorg.conf is allowed to be empty, in most simple cases Xorg can work out
> its configuration itself. I suspect you have found the problem yourself
> is -rgba is not recognised and stopping the xserver starting.
> 
> Look at the xserver-common or xserver-kdrive-common packages for the X
> startup files I lost track of which distro uses which package.
> 

I have progressed a little further, so I have managed to get
the Xserver to start, but the xorg.conf I did fails to
support the mouse. The touchscreen is also nonfunctional but
A USB keyboard work...
(The mouse actually works while I have the Angstrom splash)

Based on you email, I removed the -screen 240x320 from Xserver
and zeroed out xorg.conf, and now it also boots
but still no touch or hanlding of a mouse.

I have been able to play configure sound graphically,
and played an avi movie in full screen mode,
but mplayer did not find the DISPLAY.
export=DISPLAY=":0.0" fixed, that, but
then mplayer complained about no X compatible driver....



Some issues I have seen:
The X configuration sets up a lot of paths with "X11R6" directories
which are not present in the file system
A file called protocol.txt is missing..

The kernel is not compiled with power managements and
/usr/bin/apm --suspend does not work

There is an alignment trap after the Fontpath is set

Reports AllowEmptyInput is on, and devices using kbd and mouse is off.
WHat does this mean?

Cant find the glx and dri modules...





> Graeme
> 
> 
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel


-- 
Best Regards
Ulf Samuelsson

Re: No graphic when loading "x11-gpe-image"

[Rolf Leggewie]

Ulf Samuelsson wrote:
> I have progressed a little further, so I have managed to get
> the Xserver to start, but the xorg.conf I did fails to
> support the mouse. The touchscreen is also nonfunctional but
> A USB keyboard work...

That sounds similar to the problems I'm experiencing with X11 and Opie
in qemu images.  Poky images work, but I wasn't sure where the magic
difference between Poky and .dev could be.

Re: No graphic when loading "x11-gpe-image"

[Ulf Samuelsson]

Rolf Leggewie skrev:
> Ulf Samuelsson wrote:
>> I have progressed a little further, so I have managed to get
>> the Xserver to start, but the xorg.conf I did fails to
>> support the mouse. The touchscreen is also nonfunctional but
>> A USB keyboard work...
> 
> That sounds similar to the problems I'm experiencing with X11 and Opie
> in qemu images.  Poky images work, but I wasn't sure where the magic
> difference between Poky and .dev could be.
> 
> 
The problem was localized to the SAM9263.
Xorg was called with "-rgba bgr" and "-screen 240x320"

-rgba is not a known switch.

openembedded provides an empty xorg.conf, so the screen "240x320"
was not found.

By removing the -screen 240x320 from the Xorg startup,
the X11 server could be started, but no touchscreen.

By default, the AllowEmptyInput is on, so the input drivers
are not loaded, and this needs to be set to "off"

my xorg.conf, now only contains:
Section "ServerFlags"
	Option "AllowEmptyInput" "off"
EndSection

The touchscreen now works, but it does not calibrate,
and it is not coordinated with the movements.
I suspect FRAMEBUFFER_CONSOLE_ROTATION beeing set
might have something to do with it, but I am not sure.
When I move the pen in X direction, the cursor moves in Y direction

Also, my USB keyboard gets three events per press,
resulting in three characters.


Anyone got a fully working xorg.conf ?


> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel


-- 
Best Regards
Ulf Samuelsson

Re: No graphic when loading "x11-gpe-image" - Now mostly working!

[Ulf Samuelsson]

Ulf Samuelsson skrev:
> Rolf Leggewie skrev:
>> Ulf Samuelsson wrote:
>>> I have progressed a little further, so I have managed to get
>>> the Xserver to start, but the xorg.conf I did fails to
>>> support the mouse. The touchscreen is also nonfunctional but
>>> A USB keyboard work...
>> That sounds similar to the problems I'm experiencing with X11 and Opie
>> in qemu images.  Poky images work, but I wasn't sure where the magic
>> difference between Poky and .dev could be.
>>
>>
> The problem was localized to the SAM9263.
> Xorg was called with "-rgba bgr" and "-screen 240x320"
> 
> -rgba is not a known switch.
> 
> openembedded provides an empty xorg.conf, so the screen "240x320"
> was not found.
> 
> By removing the -screen 240x320 from the Xorg startup,
> the X11 server could be started, but no touchscreen.
> 
> By default, the AllowEmptyInput is on, so the input drivers
> are not loaded, and this needs to be set to "off"
> 
> my xorg.conf, now only contains:
> Section "ServerFlags"
> 	Option "AllowEmptyInput" "off"
> EndSection
> 
> The touchscreen now works, but it does not calibrate,
> and it is not coordinated with the movements.
> I suspect FRAMEBUFFER_CONSOLE_ROTATION beeing set
> might have something to do with it, but I am not sure.
> When I move the pen in X direction, the cursor moves in Y direction
> 
> Also, my USB keyboard gets three events per press,
> resulting in three characters.
> 
> 
> Anyone got a fully working xorg.conf ?
> 


This xorg.conf looks promising
Stops loading a keyboard and a mouse.
The characters are now one at a time,
and I have a touch functionality (but no cursor).
Unfortunately, the calibration is broken.


Section "ServerLayout"
	Identifier      "Atmel SAM9 Layout"
	Screen  	"240x320"
	InputDevice	"Touchscreen"	"CorePointer"
	InputDevice	"Keyboard"	"CoreKeyboard"
	InputDevice	"dummy"
EndSection

Section "ServerFlags"
	Option	"AllowEmptyInput" "off"
EndSection

Section "Module"
	Load    "extmod"
	Load    "dbe"
EndSection

Section "Monitor"
        Identifier      "HITACHI LCD"
EndSection

Section "Device"
        Identifier      "FrameBuffer"
        Driver		"fbdev"
EndSection

Section "Screen"
        Identifier      "240x320"
        Device  "FrameBuffer"
        Monitor "HITACHI LCD"
EndSection

Section "InputDevice"
	Identifier	"Touchscreen"
	Driver		"evdev"
	Option		"Device" "/dev/input/touchscreen0"
	Option		"DeviceName" "Touchscreen"
	Option		"MinX" "98"
	Option		"MaxX" "940"
	Option		"MinY" "43"
	Option		"MaxY" "925"
	Option		"ReportingMode" "Raw"
	Option		"Emulate3Buttons"
	Option		"Emulate3Timeout" "50"
#	Option		"CorePointer"
	Option		"SendCoreEvents" "on"
EndSection

Section "InputDevice"
	Identifier	"Keyboard"
	Driver		"dummy"
	Option		"Device" "/dev/input/event2"
EndSection


Section "InputDevice"
	Identifier	"dummy"
	Driver		"void"
	Option		"Device" "/dev/input/mice"
EndSection

----------------------------------------------------------


X.Org X Server 1.6.1
Release Date: 2009-4-14
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.27.25-0.1-default x86_64
Current Operating System: Linux at91sam9263dfc 2.6.30.2 #1 PREEMPT Fri
Aug 14 18:07:09 CEST 2009 armv5tejl
Build Date: 14 August 2009  01:57:46AM

	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Aug 15 14:03:02 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Atmel SAM9 Layout"
(**) |-->Screen "240x320" (0)
(**) |   |-->Monitor "HITACHI LCD"
(**) |   |-->Device "FrameBuffer"
(**) |-->Input Device "Touchscreen"
(**) |-->Input Device "Keyboard"
(**) |-->Input Device "dummy"
(**) Option "AllowEmptyInput" "off"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
	/usr/share/fonts/X11/misc,
	built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Loader magic: 0xfa84
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.4
	X.Org Video Driver: 5.0
	X.Org XInput driver : 4.0
	X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 2

(II) System resource ranges:
(II) "extmod" will be loaded. This was enabled by default and also
specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also
specified in the config file.
(II) "glx" will be loaded by default.
(II) "dri" will be loaded by default.
(II) "dri2" will be loaded by default.
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "fbdev"
(II) Loading /usr/lib/xorg/modules/drivers//fbdev_drv.so
(II) Module fbdev: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 0.4.0
	ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 2.2.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 4.0
(II) LoadModule: "dummy"
(WW) Warning, couldn't open module dummy
(II) UnloadModule: "dummy"
(EE) Failed to load module "dummy" (module does not exist, 0)
(II) LoadModule: "void"
(WW) Warning, couldn't open module void
(II) UnloadModule: "void"
(EE) Failed to load module "void" (module does not exist, 0)
(II) FBDEV: driver for framebuffer: fbdev
(WW) Falling back to old probe method for fbdev
(II) Loading sub module "fbdevhw"
(II) LoadModule: "fbdevhw"
(II) Loading /usr/lib/xorg/modules/linux//libfbdevhw.so
(II) Module fbdevhw: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 0.0.2
	ABI class: X.Org Video Driver, version 5.0
(II) FBDEV(0): using default device
(II) Running in FRAMEBUFFER Mode
(II) FBDEV(0): Creating default Display subsection in Screen section
	"240x320" for depth/fbbpp 15/16
(==) FBDEV(0): Depth 15, (==) framebuffer bpp 16
(==) FBDEV(0): RGB weight 555
(==) FBDEV(0): Default visual is TrueColor
(==) FBDEV(0): Using gamma correction (1.0, 1.0, 1.0)
(II) FBDEV(0): hardware:  (video memory: 150kB)
(II) FBDEV(0): checking modes against framebuffer device...
(II) FBDEV(0): checking modes against monitor...
(--) FBDEV(0): Virtual size is 240x320 (pitch 240)
(**) FBDEV(0):  Built-in mode "current": 5.0 MHz, 17.9 kHz, 55.6 Hz
(II) FBDEV(0): Modeline "current"x0.0    5.00  240 273 278 279  320 320
321 322 +hsync +vsync -csync (17.9 kHz)
(++) FBDEV(0): DPI set to (100, 100)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(**) FBDEV(0): using shadow framebuffer
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"
(II) Loading /usr/lib/xorg/modules//libshadow.so
(II) Module shadow: vendor="X.Org Foundation"
	compiled for 1.6.1, module version = 1.1.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(EE) FBDEV(0): FBIOBLANK: Invalid argument
(==) FBDEV(0): Backing store disabled
(II) FBDEV(0): DPMS enabled
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI capable
(EE) AIGLX error: dlopen of /usr/lib/dri/swrast_dri.so failed
(/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such
file or directory)
(EE) GLX: could not load software renderer
(II) GLX: no usable GL providers found for screen 0
(**) Option "SendCoreEvents" "on"
(**) Option "CorePointer"
(**) Touchscreen: always reports core events
(**) Touchscreen: Device: "/dev/input/touchscreen0"
(II) Touchscreen: Found x and y absolute axes
(II) Touchscreen: Found absolute touchscreen
(II) Touchscreen: Configuring as touchscreen
(**) Option "Emulate3Buttons"
(II) Touchscreen: Forcing middle mouse button emulation on.
(**) Option "Emulate3Timeout" "50"
(**) Touchscreen: YAxisMapping: buttons 4 and 5
(**) Touchscreen: EmulateWheelButton: 4, EmulateWheelInertia: 10,
EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Touchscreen" (type: TOUCHSCREEN)
(**) Touchscreen: (accel) keeping acceleration scheme 1
(**) Touchscreen: (accel) filter chain progression: 2.00
(**) Touchscreen: (accel) filter stage 0: 20.00 ms
(**) Touchscreen: (accel) set acceleration profile 0
(II) LoadModule: "dummy"
(WW) Warning, couldn't open module dummy
(II) UnloadModule: "dummy"
(EE) Failed to load module "dummy" (module does not exist, 0)
(EE) No input driver matching `dummy'
(II) LoadModule: "void"
(WW) Warning, couldn't open module void
(II) UnloadModule: "void"
(EE) Failed to load module "void" (module does not exist, 0)
(EE) No input driver matching `void'
(EE) FBDEV(0): FBIOBLANK: Invalid argument
(II) config/hal: Adding input device USB Keyboard
(**) USB Keyboard: always reports core events
(**) USB Keyboard: Device: "/dev/input/event3"
(II) USB Keyboard: Found 13 mouse buttons
(II) USB Keyboard: Found x and y relative axes
(II) USB Keyboard: Found scroll wheel(s)
(II) USB Keyboard: Found keys
(II) USB Keyboard: Configuring as mouse
(II) USB Keyboard: Configuring as keyboard
(**) USB Keyboard: YAxisMapping: buttons 4 and 5
(**) USB Keyboard: EmulateWheelButton: 4, EmulateWheelInertia: 10,
EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "USB Keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(**) USB Keyboard: (accel) keeping acceleration scheme 1
(**) USB Keyboard: (accel) filter chain progression: 2.00
(**) USB Keyboard: (accel) filter stage 0: 20.00 ms
(**) USB Keyboard: (accel) set acceleration profile 0
(II) config/hal: Adding input device USB Keyboard
(**) USB Keyboard: always reports core events
(**) USB Keyboard: Device: "/dev/input/event2"
(II) USB Keyboard: Found keys
(II) USB Keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "USB Keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"

>> _______________________________________________
>> Openembedded-devel mailing list
>> Openembedded-devel@lists.openembedded.org
>> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
> 
> 


-- 
Best Regards
Ulf Samuelsson

Re: No graphic when loading "x11-gpe-image"

[Stanislav Brabec]

Phil Blundell píše v Pá 14. 08. 2009 v 22:08 +0100:
> On Fri, 2009-08-14 at 22:01 +0200, Ulf Samuelsson wrote:
> > The full command line is:
> > exec Xorg -br -pn  -dpi 100 -rgba bgr -screen 240x320 :0 -noreset
> > 
> > It complains about an unrecognized option "-rgba"
> 
> Yeah, that looks like the startup scripts are trying to pass kdrive
> options to Xorg.  I guess you need to either install kdrive, or patch
> the scripts to do the right thing for Xorg.

Yes, this script is broken - it checks, whether Xorg is installed. If it
is, but the platform was originally designed for kdrive, it breaks.

There was a thread "[RFC] Xserver-common 1.30" about it few weeks ago.

Maybe a new platform specific package with a working xorg.conf will be
useful. (Future versions of Xorg may be able to start without xorg.conf,
just with auto-detection.)


________________________________________________________________________
Stanislav Brabec
http://www.penguin.cz/~utx/zaurus

Re: No graphic when loading "x11-gpe-image"

[Koen Kooi]

On 16-08-09 01:00, Stanislav Brabec wrote:
(Future versions of Xorg may be able to start without xorg.conf,
> just with auto-detection.)

The current one in OE already does, works great on all the hw I have here.

regards,

Koen

Re: No graphic when loading "x11-gpe-image"

[marcin]

Dnia Sun, 16 Aug 2009 01:00:21 +0200 napisano:

> Phil Blundell píše v Pá 14. 08. 2009 v 22:08 +0100:
> > On Fri, 2009-08-14 at 22:01 +0200, Ulf Samuelsson wrote:
> > > The full command line is:
> > > exec Xorg -br -pn  -dpi 100 -rgba bgr
> -screen 240x320 :0 -noreset
> > > 
> > > It complains about an unrecognized option "-rgba"
> > 
> > Yeah, that looks like the startup scripts are trying to pass kdrive
> > options
> to Xorg.  I guess you need to either install kdrive, or patch
> > the scripts to do the right thing for Xorg.
> 
> Yes, this script is broken - it checks, whether Xorg is installed. If it
> is, but the
> platform was originally designed for kdrive, it breaks.
> 
> There was a thread "?[RFC] Xserver-common 1.30" about it few weeks ago.
> 
> Maybe a new platform specific package with a working
> xorg.conf will be useful.

There is a xorg.conf for at91sam9263ek present in metadata - you need xserver-xorg-conf package installed with xserver-xorg 1.6.1 and evdev driver. No keyboard/mouse/tslib drivers are needed - evdev handles touchscreen on at91sam923ek just fine (even do not require calibration).

If there will be a problem with start then use xserver-common 1.30 instead of 1.25 (default one).

Re: No graphic when loading "x11-gpe-image"

[Ulf Samuelsson]

marcin@juszkiewicz.com.pl skrev:
> Dnia Sun, 16 Aug 2009 01:00:21 +0200 napisano:
> 
>> Phil Blundell píše v Pá 14. 08. 2009 v 22:08 +0100:
>>> On Fri, 2009-08-14 at 22:01 +0200, Ulf Samuelsson wrote:
>>>> The full command line is:
>>>> exec Xorg -br -pn  -dpi 100 -rgba bgr
>> -screen 240x320 :0 -noreset
>>>> It complains about an unrecognized option "-rgba"
>>> Yeah, that looks like the startup scripts are trying to pass kdrive
>>> options
>> to Xorg.  I guess you need to either install kdrive, or patch
>>> the scripts to do the right thing for Xorg.
>> Yes, this script is broken - it checks, whether Xorg is installed. If it
>> is, but the
>> platform was originally designed for kdrive, it breaks.
>>
>> There was a thread "?[RFC] Xserver-common 1.30" about it few weeks ago.
>>
>> Maybe a new platform specific package with a working
>> xorg.conf will be useful.
> 
> There is a xorg.conf for at91sam9263ek present in metadata - you need xserver-xorg-conf package installed with xserver-xorg 1.6.1 and evdev driver. No keyboard/mouse/tslib drivers are needed - evdev handles touchscreen on at91sam923ek just fine (even do not require calibration).
> 
> If there will be a problem with start then use xserver-common 1.30 instead of 1.25 (default one).
> 
> 


I have it running after some time, and I have resolve all the issues,
with the SAM9263EK except the touchscreen.

It is not fully integrated with my openembedded branch yet.
I put another jffs2 filesystem in the upper 128 MB
and patch up the stuff built by embedded by running a script
right after login which mounts the other filesystem
and copies over a lot of stuff.

Will integrate this into openembedded eventually.

> 
> 
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel


-- 
Best Regards
Ulf Samuelsson