* [PATCH 1/2] OMAP2/3 clock: Extend find_idlest() to pass back idle state value
@ 2010-01-19 9:20 Ranjith Lohithakshan
2010-02-05 20:16 ` Paul Walmsley
0 siblings, 1 reply; 4+ messages in thread
From: Ranjith Lohithakshan @ 2010-01-19 9:20 UTC (permalink / raw)
To: linux-omap; +Cc: paul, ranjithl
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.
This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
---
arch/arm/mach-omap2/clock.c | 22 ++++++++++++++++++----
arch/arm/mach-omap2/clock.h | 2 +-
arch/arm/mach-omap2/clock2xxx.c | 7 +++++--
arch/arm/mach-omap2/clock34xx.c | 15 ++++++++++++---
arch/arm/mach-omap2/cm.h | 3 +++
arch/arm/mach-omap2/prcm.c | 14 +++++---------
arch/arm/plat-omap/include/plat/clock.h | 2 +-
arch/arm/plat-omap/include/plat/prcm.h | 2 +-
8 files changed, 46 insertions(+), 21 deletions(-)
diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index 759c72a..b5cc7b7 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -351,7 +351,8 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
* omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
* @clk: struct clk * to find IDLEST info for
* @idlest_reg: void __iomem ** to return the CM_IDLEST va in
- * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
+ * @idlest_bit: u8 * to return the CM_IDLEST bit shift in
+ * @idlest_val: u8 * to return the idle status indicator
*
* Return the CM_IDLEST register address and bit shift corresponding
* to the module that "owns" this clock. This default code assumes
@@ -361,13 +362,25 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
* CM_IDLEST2). This is not true for all modules. No return value.
*/
void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit, u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = clk->enable_bit;
+
+ /*
+ * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
+ * 34xx reverses this, just to keep us on our toes
+ */
+ if (cpu_is_omap24xx())
+ *idlest_val = OMAP24XX_CM_IDLEST_VAL;
+ else if (cpu_is_omap34xx())
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
+ else
+ BUG();
+
}
/**
@@ -384,6 +397,7 @@ static void omap2_module_wait_ready(struct clk *clk)
{
void __iomem *companion_reg, *idlest_reg;
u8 other_bit, idlest_bit;
+ u8 idlest_val;
/* Not all modules have multiple clocks that their IDLEST depends on */
if (clk->ops->find_companion) {
@@ -392,9 +406,9 @@ static void omap2_module_wait_ready(struct clk *clk)
return;
}
- clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
+ clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val);
- omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
+ omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), idlest_val, clk->name);
}
int omap2_dflt_clk_enable(struct clk *clk)
diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
index 93c48df..c159503 100644
--- a/arch/arm/mach-omap2/clock.h
+++ b/arch/arm/mach-omap2/clock.h
@@ -90,7 +90,7 @@ void omap2_dflt_clk_disable(struct clk *clk);
void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
u8 *other_bit);
void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
- u8 *idlest_bit);
+ u8 *idlest_bit, u8 *idlest_val);
extern u8 cpu_mask;
diff --git a/arch/arm/mach-omap2/clock2xxx.c b/arch/arm/mach-omap2/clock2xxx.c
index 5420356..9dd5265 100644
--- a/arch/arm/mach-omap2/clock2xxx.c
+++ b/arch/arm/mach-omap2/clock2xxx.c
@@ -72,6 +72,7 @@ void __iomem *prcm_clksrc_ctrl;
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
* CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function
@@ -80,10 +81,12 @@ void __iomem *prcm_clksrc_ctrl;
*/
static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
*idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
*idlest_bit = clk->enable_bit;
+ *idlest_val = OMAP24XX_CM_IDLEST_VAL;
}
/* 2430 I2CHS has non-standard IDLEST register */
@@ -176,7 +179,7 @@ static int omap2_clk_apll_enable(struct clk *clk, u32 status_mask)
cm_write_mod_reg(cval, PLL_MOD, CM_CLKEN);
omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), status_mask,
- clk->name);
+ OMAP24XX_CM_IDLEST_VAL, clk->name);
/*
* REVISIT: Should we return an error code if omap2_wait_clock_ready()
diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index d4217b9..97752e4 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -59,6 +59,7 @@ struct clk *sdrc_ick_p, *arm_fck_p;
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
* from the CM_{I,F}CLKEN bit. Pass back the correct info via
@@ -66,13 +67,15 @@ struct clk *sdrc_ick_p, *arm_fck_p;
*/
static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
}
const struct clkops clkops_omap3430es2_ssi_wait = {
@@ -87,6 +90,7 @@ const struct clkops clkops_omap3430es2_ssi_wait = {
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* Some OMAP modules on OMAP3 ES2+ chips have both initiator and
* target IDLEST bits. For our purposes, we are concerned with the
@@ -97,7 +101,8 @@ const struct clkops clkops_omap3430es2_ssi_wait = {
*/
static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
u32 r;
@@ -105,6 +110,7 @@ static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
*idlest_reg = (__force void __iomem *)r;
/* USBHOST_IDLE has same shift */
*idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
}
const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
@@ -119,6 +125,7 @@ const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
* shift from the CM_{I,F}CLKEN bit. Pass back the correct info via
@@ -126,13 +133,15 @@ const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
*/
static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
}
const struct clkops clkops_omap3430es2_hsotgusb_wait = {
diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h
index 90a4086..be77daa 100644
--- a/arch/arm/mach-omap2/cm.h
+++ b/arch/arm/mach-omap2/cm.h
@@ -138,5 +138,8 @@ static inline u32 cm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
/* CM_IDLEST_GFX */
#define OMAP_ST_GFX (1 << 0)
+/* CM_IDLEST indicator */
+#define OMAP24XX_CM_IDLEST_VAL 0
+#define OMAP34XX_CM_IDLEST_VAL 1
#endif
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index 3ea8177..3552df7 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -220,26 +220,22 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
* omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
* @reg: physical address of module IDLEST register
* @mask: value to mask against to determine if the module is active
+ * @idlest: idle state indicator (0 or 1) for the clock
* @name: name of the clock (for printk)
*
* Returns 1 if the module indicated readiness in time, or 0 if it
* failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
*/
-int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name)
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
+ const char *name)
{
int i = 0;
int ena = 0;
- /*
- * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
- * 34xx reverses this, just to keep us on our toes
- */
- if (cpu_is_omap24xx())
- ena = mask;
- else if (cpu_is_omap34xx())
+ if (idlest)
ena = 0;
else
- BUG();
+ ena = mask;
/* Wait for lock */
omap_test_timeout(((__raw_readl(reg) & mask) == ena),
diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h
index 94fe2a0..df5072d 100644
--- a/arch/arm/plat-omap/include/plat/clock.h
+++ b/arch/arm/plat-omap/include/plat/clock.h
@@ -22,7 +22,7 @@ struct clockdomain;
struct clkops {
int (*enable)(struct clk *);
void (*disable)(struct clk *);
- void (*find_idlest)(struct clk *, void __iomem **, u8 *);
+ void (*find_idlest)(struct clk *, void __iomem **, u8 *, u8 *);
void (*find_companion)(struct clk *, void __iomem **, u8 *);
};
diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
index e63e94e..329c05a 100644
--- a/arch/arm/plat-omap/include/plat/prcm.h
+++ b/arch/arm/plat-omap/include/plat/prcm.h
@@ -25,7 +25,7 @@
u32 omap_prcm_get_reset_sources(void);
void omap_prcm_arch_reset(char mode);
-int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name);
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest, const char *name);
#define START_PADCONF_SAVE 0x2
#define PADCONF_SAVE_DONE 0x1
--
1.6.2.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2] OMAP2/3 clock: Extend find_idlest() to pass back idle state value
2010-01-19 9:20 [PATCH 1/2] OMAP2/3 clock: Extend find_idlest() to pass back idle state value Ranjith Lohithakshan
@ 2010-02-05 20:16 ` Paul Walmsley
2010-02-08 17:34 ` Ranjith Lohithakshan
0 siblings, 1 reply; 4+ messages in thread
From: Paul Walmsley @ 2010-02-05 20:16 UTC (permalink / raw)
To: Ranjith Lohithakshan; +Cc: linux-omap
Hi Ranjith,
On Tue, 19 Jan 2010, Ranjith Lohithakshan wrote:
> Current implementation defines clock idle state indicators based on the
> cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
> manner. This patch extends the find_idlest() function in clkops to pass
> back the idle state indicator for that clock, thus allowing idle state
> indicators to be defined on a per clock basis if required.
>
> This is specifically needed on AM35xx devices as the new IPSS clocks
> indicates the idle status (0 is idle, 1 is ready) in a way just
> opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
>
> Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
I had to make some changes to this patch for it to apply after the recent
clock split patches. Could you please check this patch and make sure it
is okay?
- Paul
From: Ranjith Lohithakshan <ranjithl@ti.com>
Date: Fri, 5 Feb 2010 12:55:21 -0700
Subject: [PATCH] OMAP2/3 clock: Extend find_idlest() to pass back idle state value
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.
This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
arch/arm/mach-omap2/clkt2xxx_apll.c | 2 +-
arch/arm/mach-omap2/clock.c | 25 ++++++++++++++++++++-----
arch/arm/mach-omap2/clock.h | 2 +-
arch/arm/mach-omap2/clock2xxx.c | 5 ++++-
arch/arm/mach-omap2/clock34xx.c | 15 ++++++++++++---
arch/arm/mach-omap2/cm.h | 3 +++
arch/arm/mach-omap2/prcm.c | 14 +++++---------
arch/arm/plat-omap/include/plat/clock.h | 6 ++++--
arch/arm/plat-omap/include/plat/prcm.h | 3 ++-
9 files changed, 52 insertions(+), 23 deletions(-)
diff --git a/arch/arm/mach-omap2/clkt2xxx_apll.c b/arch/arm/mach-omap2/clkt2xxx_apll.c
index fc32ff8..d5b8b2b 100644
--- a/arch/arm/mach-omap2/clkt2xxx_apll.c
+++ b/arch/arm/mach-omap2/clkt2xxx_apll.c
@@ -57,7 +57,7 @@ static int omap2_clk_apll_enable(struct clk *clk, u32 status_mask)
cm_write_mod_reg(cval, PLL_MOD, CM_CLKEN);
omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), status_mask,
- clk->name);
+ OMAP24XX_CM_IDLEST_VAL, clk->name);
/*
* REVISIT: Should we return an error code if omap2_wait_clock_ready()
diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index 999b91e..3bb3292 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -57,7 +57,7 @@ u8 cpu_mask;
static void _omap2_module_wait_ready(struct clk *clk)
{
void __iomem *companion_reg, *idlest_reg;
- u8 other_bit, idlest_bit;
+ u8 other_bit, idlest_bit, idlest_val;
/* Not all modules have multiple clocks that their IDLEST depends on */
if (clk->ops->find_companion) {
@@ -66,9 +66,10 @@ static void _omap2_module_wait_ready(struct clk *clk)
return;
}
- clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
+ clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val);
- omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
+ omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), idlest_val,
+ clk->name);
}
/* Enables clock without considering parent dependencies or use count
@@ -175,7 +176,8 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
* omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
* @clk: struct clk * to find IDLEST info for
* @idlest_reg: void __iomem ** to return the CM_IDLEST va in
- * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
+ * @idlest_bit: u8 * to return the CM_IDLEST bit shift in
+ * @idlest_val: u8 * to return the idle status indicator
*
* Return the CM_IDLEST register address and bit shift corresponding
* to the module that "owns" this clock. This default code assumes
@@ -185,13 +187,26 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
* CM_IDLEST2). This is not true for all modules. No return value.
*/
void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit, u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = clk->enable_bit;
+
+ /*
+ * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
+ * 34xx reverses this, just to keep us on our toes
+ * AM35xx uses both, depending on the module.
+ */
+ if (cpu_is_omap24xx())
+ *idlest_val = OMAP24XX_CM_IDLEST_VAL;
+ else if (cpu_is_omap34xx())
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
+ else
+ BUG();
+
}
int omap2_dflt_clk_enable(struct clk *clk)
diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
index 7bc344b..c500a5f 100644
--- a/arch/arm/mach-omap2/clock.h
+++ b/arch/arm/mach-omap2/clock.h
@@ -88,7 +88,7 @@ void omap2_dflt_clk_disable(struct clk *clk);
void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
u8 *other_bit);
void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
- u8 *idlest_bit);
+ u8 *idlest_bit, u8 *idlest_val);
void omap2xxx_clk_commit(struct clk *clk);
extern u8 cpu_mask;
diff --git a/arch/arm/mach-omap2/clock2xxx.c b/arch/arm/mach-omap2/clock2xxx.c
index a48b01a..94fb8a6 100644
--- a/arch/arm/mach-omap2/clock2xxx.c
+++ b/arch/arm/mach-omap2/clock2xxx.c
@@ -42,6 +42,7 @@ struct clk *vclk, *sclk, *dclk;
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
* CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function
@@ -50,10 +51,12 @@ struct clk *vclk, *sclk, *dclk;
*/
static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
*idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
*idlest_bit = clk->enable_bit;
+ *idlest_val = OMAP24XX_CM_IDLEST_VAL;
}
#else
diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index 1f1b5a6..d339d2b 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -47,6 +47,7 @@ struct clk *sdrc_ick_p, *arm_fck_p;
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
* from the CM_{I,F}CLKEN bit. Pass back the correct info via
@@ -54,13 +55,15 @@ struct clk *sdrc_ick_p, *arm_fck_p;
*/
static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
}
const struct clkops clkops_omap3430es2_ssi_wait = {
@@ -75,6 +78,7 @@ const struct clkops clkops_omap3430es2_ssi_wait = {
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* Some OMAP modules on OMAP3 ES2+ chips have both initiator and
* target IDLEST bits. For our purposes, we are concerned with the
@@ -85,7 +89,8 @@ const struct clkops clkops_omap3430es2_ssi_wait = {
*/
static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
u32 r;
@@ -93,6 +98,7 @@ static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
*idlest_reg = (__force void __iomem *)r;
/* USBHOST_IDLE has same shift */
*idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
}
const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
@@ -107,6 +113,7 @@ const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
*
* The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
* shift from the CM_{I,F}CLKEN bit. Pass back the correct info via
@@ -114,13 +121,15 @@ const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
*/
static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
- u8 *idlest_bit)
+ u8 *idlest_bit,
+ u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
+ *idlest_val = OMAP34XX_CM_IDLEST_VAL;
}
const struct clkops clkops_omap3430es2_hsotgusb_wait = {
diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h
index 4e4ac8c..94728b1 100644
--- a/arch/arm/mach-omap2/cm.h
+++ b/arch/arm/mach-omap2/cm.h
@@ -139,5 +139,8 @@ static inline u32 cm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
/* CM_IDLEST_GFX */
#define OMAP_ST_GFX (1 << 0)
+/* CM_IDLEST indicator */
+#define OMAP24XX_CM_IDLEST_VAL 0
+#define OMAP34XX_CM_IDLEST_VAL 1
#endif
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index e8e121a..0f87fdc 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -242,26 +242,22 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
* omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
* @reg: physical address of module IDLEST register
* @mask: value to mask against to determine if the module is active
+ * @idlest: idle state indicator (0 or 1) for the clock
* @name: name of the clock (for printk)
*
* Returns 1 if the module indicated readiness in time, or 0 if it
* failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
*/
-int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name)
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
+ const char *name)
{
int i = 0;
int ena = 0;
- /*
- * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
- * 34xx reverses this, just to keep us on our toes
- */
- if (cpu_is_omap24xx())
- ena = mask;
- else if (cpu_is_omap34xx())
+ if (idlest)
ena = 0;
else
- BUG();
+ ena = mask;
/* Wait for lock */
omap_test_timeout(((__raw_readl(reg) & mask) == ena),
diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h
index e413132..9042dab 100644
--- a/arch/arm/plat-omap/include/plat/clock.h
+++ b/arch/arm/plat-omap/include/plat/clock.h
@@ -22,8 +22,10 @@ struct clockdomain;
struct clkops {
int (*enable)(struct clk *);
void (*disable)(struct clk *);
- void (*find_idlest)(struct clk *, void __iomem **, u8 *);
- void (*find_companion)(struct clk *, void __iomem **, u8 *);
+ void (*find_idlest)(struct clk *, void __iomem **,
+ u8 *, u8 *);
+ void (*find_companion)(struct clk *, void __iomem **,
+ u8 *);
};
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
index 66938a9..d6a0e27 100644
--- a/arch/arm/plat-omap/include/plat/prcm.h
+++ b/arch/arm/plat-omap/include/plat/prcm.h
@@ -25,7 +25,8 @@
u32 omap_prcm_get_reset_sources(void);
void omap_prcm_arch_reset(char mode);
-int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name);
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
+ const char *name);
#define START_PADCONF_SAVE 0x2
#define PADCONF_SAVE_DONE 0x1
--
1.6.6.rc2.5.g49666
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2] OMAP2/3 clock: Extend find_idlest() to pass back idle state value
2010-02-05 20:16 ` Paul Walmsley
@ 2010-02-08 17:34 ` Ranjith Lohithakshan
2010-02-08 17:37 ` Paul Walmsley
0 siblings, 1 reply; 4+ messages in thread
From: Ranjith Lohithakshan @ 2010-02-08 17:34 UTC (permalink / raw)
To: Paul Walmsley; +Cc: linux-omap@vger.kernel.org
Hi Paul,
On Sat, 06-Feb-10 1:46 AM +0530, Paul Walmsley wrote:
> Hi Ranjith,
>
> On Tue, 19 Jan 2010, Ranjith Lohithakshan wrote:
>
>> Current implementation defines clock idle state indicators based on the
>> cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
>> manner. This patch extends the find_idlest() function in clkops to pass
>> back the idle state indicator for that clock, thus allowing idle state
>> indicators to be defined on a per clock basis if required.
>>
>> This is specifically needed on AM35xx devices as the new IPSS clocks
>> indicates the idle status (0 is idle, 1 is ready) in a way just
>> opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
>>
>> Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
>
> I had to make some changes to this patch for it to apply after the recent
> clock split patches. Could you please check this patch and make sure it
> is okay?
It looks good to me. I have verified these latest changes on AM3517 EVM
- Ranjith
> - Paul
>
>
> From: Ranjith Lohithakshan <ranjithl@ti.com>
> Date: Fri, 5 Feb 2010 12:55:21 -0700
> Subject: [PATCH] OMAP2/3 clock: Extend find_idlest() to pass back idle state value
>
> Current implementation defines clock idle state indicators based on the
> cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
> manner. This patch extends the find_idlest() function in clkops to pass
> back the idle state indicator for that clock, thus allowing idle state
> indicators to be defined on a per clock basis if required.
>
> This is specifically needed on AM35xx devices as the new IPSS clocks
> indicates the idle status (0 is idle, 1 is ready) in a way just
> opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
>
> Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
> [paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
> Signed-off-by: Paul Walmsley <paul@pwsan.com>
> ---
> arch/arm/mach-omap2/clkt2xxx_apll.c | 2 +-
> arch/arm/mach-omap2/clock.c | 25 ++++++++++++++++++++-----
> arch/arm/mach-omap2/clock.h | 2 +-
> arch/arm/mach-omap2/clock2xxx.c | 5 ++++-
> arch/arm/mach-omap2/clock34xx.c | 15 ++++++++++++---
> arch/arm/mach-omap2/cm.h | 3 +++
> arch/arm/mach-omap2/prcm.c | 14 +++++---------
> arch/arm/plat-omap/include/plat/clock.h | 6 ++++--
> arch/arm/plat-omap/include/plat/prcm.h | 3 ++-
> 9 files changed, 52 insertions(+), 23 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/clkt2xxx_apll.c b/arch/arm/mach-omap2/clkt2xxx_apll.c
> index fc32ff8..d5b8b2b 100644
> --- a/arch/arm/mach-omap2/clkt2xxx_apll.c
> +++ b/arch/arm/mach-omap2/clkt2xxx_apll.c
> @@ -57,7 +57,7 @@ static int omap2_clk_apll_enable(struct clk *clk, u32 status_mask)
> cm_write_mod_reg(cval, PLL_MOD, CM_CLKEN);
>
> omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), status_mask,
> - clk->name);
> + OMAP24XX_CM_IDLEST_VAL, clk->name);
>
> /*
> * REVISIT: Should we return an error code if omap2_wait_clock_ready()
> diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
> index 999b91e..3bb3292 100644
> --- a/arch/arm/mach-omap2/clock.c
> +++ b/arch/arm/mach-omap2/clock.c
> @@ -57,7 +57,7 @@ u8 cpu_mask;
> static void _omap2_module_wait_ready(struct clk *clk)
> {
> void __iomem *companion_reg, *idlest_reg;
> - u8 other_bit, idlest_bit;
> + u8 other_bit, idlest_bit, idlest_val;
>
> /* Not all modules have multiple clocks that their IDLEST depends on */
> if (clk->ops->find_companion) {
> @@ -66,9 +66,10 @@ static void _omap2_module_wait_ready(struct clk *clk)
> return;
> }
>
> - clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
> + clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val);
>
> - omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
> + omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), idlest_val,
> + clk->name);
> }
>
> /* Enables clock without considering parent dependencies or use count
> @@ -175,7 +176,8 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
> * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
> * @clk: struct clk * to find IDLEST info for
> * @idlest_reg: void __iomem ** to return the CM_IDLEST va in
> - * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
> + * @idlest_bit: u8 * to return the CM_IDLEST bit shift in
> + * @idlest_val: u8 * to return the idle status indicator
> *
> * Return the CM_IDLEST register address and bit shift corresponding
> * to the module that "owns" this clock. This default code assumes
> @@ -185,13 +187,26 @@ void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
> * CM_IDLEST2). This is not true for all modules. No return value.
> */
> void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
> - u8 *idlest_bit)
> + u8 *idlest_bit, u8 *idlest_val)
> {
> u32 r;
>
> r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
> *idlest_reg = (__force void __iomem *)r;
> *idlest_bit = clk->enable_bit;
> +
> + /*
> + * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
> + * 34xx reverses this, just to keep us on our toes
> + * AM35xx uses both, depending on the module.
> + */
> + if (cpu_is_omap24xx())
> + *idlest_val = OMAP24XX_CM_IDLEST_VAL;
> + else if (cpu_is_omap34xx())
> + *idlest_val = OMAP34XX_CM_IDLEST_VAL;
> + else
> + BUG();
> +
> }
>
> int omap2_dflt_clk_enable(struct clk *clk)
> diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
> index 7bc344b..c500a5f 100644
> --- a/arch/arm/mach-omap2/clock.h
> +++ b/arch/arm/mach-omap2/clock.h
> @@ -88,7 +88,7 @@ void omap2_dflt_clk_disable(struct clk *clk);
> void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
> u8 *other_bit);
> void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
> - u8 *idlest_bit);
> + u8 *idlest_bit, u8 *idlest_val);
> void omap2xxx_clk_commit(struct clk *clk);
>
> extern u8 cpu_mask;
> diff --git a/arch/arm/mach-omap2/clock2xxx.c b/arch/arm/mach-omap2/clock2xxx.c
> index a48b01a..94fb8a6 100644
> --- a/arch/arm/mach-omap2/clock2xxx.c
> +++ b/arch/arm/mach-omap2/clock2xxx.c
> @@ -42,6 +42,7 @@ struct clk *vclk, *sclk, *dclk;
> * @clk: struct clk * being enabled
> * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
> * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
> + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
> *
> * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
> * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function
> @@ -50,10 +51,12 @@ struct clk *vclk, *sclk, *dclk;
> */
> static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
> void __iomem **idlest_reg,
> - u8 *idlest_bit)
> + u8 *idlest_bit,
> + u8 *idlest_val)
> {
> *idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
> *idlest_bit = clk->enable_bit;
> + *idlest_val = OMAP24XX_CM_IDLEST_VAL;
> }
>
> #else
> diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
> index 1f1b5a6..d339d2b 100644
> --- a/arch/arm/mach-omap2/clock34xx.c
> +++ b/arch/arm/mach-omap2/clock34xx.c
> @@ -47,6 +47,7 @@ struct clk *sdrc_ick_p, *arm_fck_p;
> * @clk: struct clk * being enabled
> * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
> * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
> + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
> *
> * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
> * from the CM_{I,F}CLKEN bit. Pass back the correct info via
> @@ -54,13 +55,15 @@ struct clk *sdrc_ick_p, *arm_fck_p;
> */
> static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
> void __iomem **idlest_reg,
> - u8 *idlest_bit)
> + u8 *idlest_bit,
> + u8 *idlest_val)
> {
> u32 r;
>
> r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
> *idlest_reg = (__force void __iomem *)r;
> *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
> + *idlest_val = OMAP34XX_CM_IDLEST_VAL;
> }
>
> const struct clkops clkops_omap3430es2_ssi_wait = {
> @@ -75,6 +78,7 @@ const struct clkops clkops_omap3430es2_ssi_wait = {
> * @clk: struct clk * being enabled
> * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
> * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
> + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
> *
> * Some OMAP modules on OMAP3 ES2+ chips have both initiator and
> * target IDLEST bits. For our purposes, we are concerned with the
> @@ -85,7 +89,8 @@ const struct clkops clkops_omap3430es2_ssi_wait = {
> */
> static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
> void __iomem **idlest_reg,
> - u8 *idlest_bit)
> + u8 *idlest_bit,
> + u8 *idlest_val)
> {
> u32 r;
>
> @@ -93,6 +98,7 @@ static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
> *idlest_reg = (__force void __iomem *)r;
> /* USBHOST_IDLE has same shift */
> *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
> + *idlest_val = OMAP34XX_CM_IDLEST_VAL;
> }
>
> const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
> @@ -107,6 +113,7 @@ const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
> * @clk: struct clk * being enabled
> * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
> * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
> + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator
> *
> * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
> * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via
> @@ -114,13 +121,15 @@ const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
> */
> static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
> void __iomem **idlest_reg,
> - u8 *idlest_bit)
> + u8 *idlest_bit,
> + u8 *idlest_val)
> {
> u32 r;
>
> r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
> *idlest_reg = (__force void __iomem *)r;
> *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
> + *idlest_val = OMAP34XX_CM_IDLEST_VAL;
> }
>
> const struct clkops clkops_omap3430es2_hsotgusb_wait = {
> diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h
> index 4e4ac8c..94728b1 100644
> --- a/arch/arm/mach-omap2/cm.h
> +++ b/arch/arm/mach-omap2/cm.h
> @@ -139,5 +139,8 @@ static inline u32 cm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
> /* CM_IDLEST_GFX */
> #define OMAP_ST_GFX (1 << 0)
>
> +/* CM_IDLEST indicator */
> +#define OMAP24XX_CM_IDLEST_VAL 0
> +#define OMAP34XX_CM_IDLEST_VAL 1
>
> #endif
> diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
> index e8e121a..0f87fdc 100644
> --- a/arch/arm/mach-omap2/prcm.c
> +++ b/arch/arm/mach-omap2/prcm.c
> @@ -242,26 +242,22 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
> * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
> * @reg: physical address of module IDLEST register
> * @mask: value to mask against to determine if the module is active
> + * @idlest: idle state indicator (0 or 1) for the clock
> * @name: name of the clock (for printk)
> *
> * Returns 1 if the module indicated readiness in time, or 0 if it
> * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
> */
> -int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name)
> +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
> + const char *name)
> {
> int i = 0;
> int ena = 0;
>
> - /*
> - * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
> - * 34xx reverses this, just to keep us on our toes
> - */
> - if (cpu_is_omap24xx())
> - ena = mask;
> - else if (cpu_is_omap34xx())
> + if (idlest)
> ena = 0;
> else
> - BUG();
> + ena = mask;
>
> /* Wait for lock */
> omap_test_timeout(((__raw_readl(reg) & mask) == ena),
> diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h
> index e413132..9042dab 100644
> --- a/arch/arm/plat-omap/include/plat/clock.h
> +++ b/arch/arm/plat-omap/include/plat/clock.h
> @@ -22,8 +22,10 @@ struct clockdomain;
> struct clkops {
> int (*enable)(struct clk *);
> void (*disable)(struct clk *);
> - void (*find_idlest)(struct clk *, void __iomem **, u8 *);
> - void (*find_companion)(struct clk *, void __iomem **, u8 *);
> + void (*find_idlest)(struct clk *, void __iomem **,
> + u8 *, u8 *);
> + void (*find_companion)(struct clk *, void __iomem **,
> + u8 *);
> };
>
> #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
> diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
> index 66938a9..d6a0e27 100644
> --- a/arch/arm/plat-omap/include/plat/prcm.h
> +++ b/arch/arm/plat-omap/include/plat/prcm.h
> @@ -25,7 +25,8 @@
>
> u32 omap_prcm_get_reset_sources(void);
> void omap_prcm_arch_reset(char mode);
> -int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name);
> +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
> + const char *name);
>
> #define START_PADCONF_SAVE 0x2
> #define PADCONF_SAVE_DONE 0x1
> --
> 1.6.6.rc2.5.g49666
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2] OMAP2/3 clock: Extend find_idlest() to pass back idle state value
2010-02-08 17:34 ` Ranjith Lohithakshan
@ 2010-02-08 17:37 ` Paul Walmsley
0 siblings, 0 replies; 4+ messages in thread
From: Paul Walmsley @ 2010-02-08 17:37 UTC (permalink / raw)
To: Ranjith Lohithakshan; +Cc: linux-omap@vger.kernel.org
Hi Ranjith,
On Mon, 8 Feb 2010, Ranjith Lohithakshan wrote:
> On Sat, 06-Feb-10 1:46 AM +0530, Paul Walmsley wrote:
> >
> > I had to make some changes to this patch for it to apply after the recent
> > clock split patches. Could you please check this patch and make sure it
> > is okay?
>
> It looks good to me. I have verified these latest changes on AM3517 EVM
Thanks, queued for 2.6.34.
- Paul
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2010-02-08 17:37 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-19 9:20 [PATCH 1/2] OMAP2/3 clock: Extend find_idlest() to pass back idle state value Ranjith Lohithakshan
2010-02-05 20:16 ` Paul Walmsley
2010-02-08 17:34 ` Ranjith Lohithakshan
2010-02-08 17:37 ` Paul Walmsley
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.