From: Jonathan Thibault <jonathan@navigue.com>
To: alsa-devel@alsa-project.org
Subject: Re: STAC9200 spdif output problem on Dell Precision M65
Date: Sun, 28 Feb 2010 18:08:06 -0500 [thread overview]
Message-ID: <4B8AF756.5060500@navigue.com> (raw)
In-Reply-To: <4B8AEB9D.3040704@navigue.com>
I probably should have specified. I see the spdif output and all its controls, I can play to it, it just won't output any data data to the spdif port.
On 28/02/10 05:18 PM, Jonathan Thibault wrote:
> Hello alsa devs :)
>
> I've tried to change the pin configuration for model=dell-m22 to match that of the windows driver as per this section of the relevant .INI file, but that hasn't really changed anything. I haven't really incorporated the windows gpio settings as I couldn't find figure out how to do so.
>
> Jonathan
>
> ---- relevant bits of windows .ini ----
> [HKR\Settings\pin]
> CodecName = STAC9200-32
> [HKR\Settings\pin\08]
> CfgDflt = dword: 0x40C003FA
> [HKR\Settings\pin\09]
> CfgDflt = dword: 0x01441340
> [HKR\Settings\pin\10]
> CfgDflt = dword: 0x03A1102E
> AltCfg = hex: 2F,10,81,03
> Bias = hex: FF,04,02
> [HKR\Settings\pin\11]
> CfgDflt = dword: 0x401003FB
> [HKR\Settings\pin\12]
> CfgDflt = dword: 0x403003FC
> [HKR\Settings\pin\0d]
> CfgDflt = dword: 0x0321121F
> Action = hex: 80,00,81,0E,87,00
> [HKR\Settings\pin\0e]
> CfgDflt = dword: 0x90170310
> [HKR\Settings\pin\0F]
> CfgDflt = dword: 0x90A70320
> ...
> [HKR\Settings\gpio]
> 02 = hex: 0x00, 0x01, 0x0E, 0x00, 0x00, 0x07, 0x00
> 01 = hex: 0x82
> 03 = hex: 0x82
> ----------------------------------------
>
> Here is the codec information.
>
> cat /proc/asound/card0/codec#0
> Codec: SigmaTel STAC9200
> Address: 0
> Function Id: 0x1
> Vendor Id: 0x83847690
> Subsystem Id: 0x102801c8
> Revision Id: 0x102201
> No Modem Function Group found
> Default PCM:
> rates [0x7e0]: 44100 48000 88200 96000 176400 192000
> bits [0xe]: 16 20 24
> formats [0x1]: PCM
> Default Amp-In caps: N/A
> Default Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1
> GPIO: io=4, o=0, i=0, unsolicited=1, wake=1
> IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
> IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
> IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
> IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
> Node 0x02 [Audio Output] wcaps 0xd0401: Stereo
> Converter: stream=5, channel=0
> Power: setting=D0, actual=D0
> Delay: 13 samples
> Node 0x03 [Audio Input] wcaps 0x1d0541: Stereo
> Converter: stream=0, channel=0
> SDI-Select: 0
> Power: setting=D0, actual=D0
> Delay: 13 samples
> Connection: 1
> 0x0a
> Processing caps: benign=0, ncoeff=0
> Node 0x04 [Audio Input] wcaps 0x140311: Stereo Digital
> Converter: stream=0, channel=0
> SDI-Select: 0
> Digital:
> Digital category: 0x0
> PCM:
> rates [0x160]: 44100 48000 96000
> bits [0xe]: 16 20 24
> formats [0x5]: PCM AC3
> Delay: 4 samples
> Connection: 1
> 0x08
> Node 0x05 [Audio Output] wcaps 0x40211: Stereo Digital
> Converter: stream=5, channel=0
> Digital:
> Digital category: 0x0
> PCM:
> rates [0x1e0]: 44100 48000 88200 96000
> bits [0xe]: 16 20 24
> formats [0x5]: PCM AC3
> Delay: 4 samples
> Node 0x06 [Vendor Defined Widget] wcaps 0xf30201: Stereo Digital
> Delay: 3 samples
> Node 0x07 [Audio Selector] wcaps 0x300901: Stereo R/L
> Connection: 3
> 0x02* 0x08 0x0a
> Node 0x08 [Pin Complex] wcaps 0x430681: Stereo Digital
> Pincap 0x00010024: IN EAPD Detect
> EAPD 0x0:
> Pin Default 0x40c003fa: [N/A] SPDIF In at Ext N/A
> Conn = Unknown, Color = Unknown
> DefAssociation = 0xf, Sequence = 0xa
> Misc = NO_PRESENCE
> Pin-ctls: 0x00:
> Unsolicited: tag=00, enabled=0
> Power: setting=D0, actual=D0
> Delay: 3 samples
> Node 0x09 [Pin Complex] wcaps 0x400301: Stereo Digital
> Pincap 0x00000010: OUT
> Pin Default 0x01441340: [Jack] SPDIF Out at Ext Rear
> Conn = RCA, Color = Black
> DefAssociation = 0x4, Sequence = 0x0
> Misc = NO_PRESENCE
> Pin-ctls: 0x40: OUT
> Connection: 2
> 0x05* 0x0a
> Node 0x0a [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
> Amp-Out caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1
> Amp-Out vals: [0x08 0x08]
> Connection: 1
> 0x0c
> Node 0x0b [Audio Selector] wcaps 0x300105: Stereo Amp-Out
> Amp-Out caps: N/A
> Amp-Out vals: [0x19 0x19]
> Connection: 1
> 0x07
> Node 0x0c [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
> Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
> Amp-Out vals: [0x00 0x00]
> Connection: 5
> 0x10 0x0f* 0x0e 0x0d 0x12
> Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
> Pincap 0x0000003f: IN OUT HP Detect Trigger ImpSense
> Pin Default 0x0321121f: [Jack] HP Out at Ext Left
> Conn = 1/8, Color = Black
> DefAssociation = 0x1, Sequence = 0xf
> Pin-ctls: 0x00:
> Unsolicited: tag=01, enabled=1
> Connection: 1
> 0x0b
> Node 0x0e [Pin Complex] wcaps 0x400181: Stereo
> Pincap 0x0000003f: IN OUT HP Detect Trigger ImpSense
> Pin Default 0x90170310: [Fixed] Speaker at Int N/A
> Conn = Analog, Color = Unknown
> DefAssociation = 0x1, Sequence = 0x0
> Misc = NO_PRESENCE
> Pin-ctls: 0x40: OUT
> Unsolicited: tag=00, enabled=0
> Connection: 1
> 0x0b
> Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
> Pincap 0x00000037: IN OUT Detect Trigger ImpSense
> Pin Default 0x90a70320: [Fixed] Mic at Int N/A
> Conn = Analog, Color = Unknown
> DefAssociation = 0x2, Sequence = 0x0
> Misc = NO_PRESENCE
> Pin-ctls: 0x20: IN
> Unsolicited: tag=00, enabled=0
> Connection: 1
> 0x0b
> Node 0x10 [Pin Complex] wcaps 0x400181: Stereo
> Pincap 0x00001737: IN OUT Detect Trigger ImpSense
> Vref caps: HIZ 50 GRD 80
> Pin Default 0x0381102f: [Jack] Line In at Ext Left
> Conn = 1/8, Color = Black
> DefAssociation = 0x2, Sequence = 0xf
> Pin-ctls: 0x20: IN VREF_HIZ
> Unsolicited: tag=02, enabled=1
> Connection: 1
> 0x0b
> Node 0x11 [Pin Complex] wcaps 0x400104: Mono Amp-Out
> Amp-Out caps: N/A
> Amp-Out vals: [0x00]
> Pincap 0x00000010: OUT
> Pin Default 0x401003fb: [N/A] Speaker at Ext N/A
> Conn = Unknown, Color = Unknown
> DefAssociation = 0xf, Sequence = 0xb
> Misc = NO_PRESENCE
> Pin-ctls: 0x00:
> Connection: 1
> 0x13
> Node 0x12 [Pin Complex] wcaps 0x400001: Stereo
> Pincap 0x00000020: IN
> Pin Default 0x403003fc: [N/A] CD at Ext N/A
> Conn = Unknown, Color = Unknown
> DefAssociation = 0xf, Sequence = 0xc
> Misc = NO_PRESENCE
> Pin-ctls: 0x20: IN
> Node 0x13 [Audio Mixer] wcaps 0x200100: Mono
> Connection: 1
> 0x07
> Node 0x14 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
> Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=1
> Amp-Out vals: [0x00]
>
>
> cat /proc/asound/card0/codec#1
> Codec: Conexant ID 2bfa
> Address: 1
> Function Id: 0x2
> Vendor Id: 0x14f12bfa
> Subsystem Id: 0x14f100c3
> Revision Id: 0x90000
> Modem Function Group: 0x2
>
>
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel@alsa-project.org
> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
prev parent reply other threads:[~2010-02-28 23:08 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-28 22:18 STAC9200 spdif output problem on Dell Precision M65 Jonathan Thibault
2010-02-28 23:08 ` Jonathan Thibault [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B8AF756.5060500@navigue.com \
--to=jonathan@navigue.com \
--cc=alsa-devel@alsa-project.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.