From: Udo van den Heuvel <udovdh@xs4all.nl>
To: linux-kernel@vger.kernel.org
Subject: 2.6.33 on jetway nc81-lf board
Date: Mon, 01 Mar 2010 19:21:12 +0100 [thread overview]
Message-ID: <4B8C0598.2060000@xs4all.nl> (raw)
Hello,
I just compiled 2.6.33 on a Jetway NC81-LF board with AMD 235E CPU.
While trying to get lm_sensors to work I get in dmesg stuff like:
f71882fg: Found f71862fg chip at 0x220, revision 18
ACPI: I/O resource f71882fg [0x220-0x227] conflicts with ACPI region
IP__ [0x225-0x226]
ACPI: If an ACPI driver is available for this device, you should use it
instead of the native driver
ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region
SOR1 [0xb00-0xb0f]
ACPI: If an ACPI driver is available for this device, you should use it
instead of the native driver
No other sensor-related modules are loaded.
What could be wrong?
# lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge
(int gfx)
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge
(PCIE port 0)
00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge
(PCIE port 1)
00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA
Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0
Controller
00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0
Controller
00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2
Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron,
Athlon64, Sempron] HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron,
Athlon64, Sempron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron,
Athlon64, Sempron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron,
Athlon64, Sempron] Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron,
Athlon64, Sempron] Link Control
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3200
Graphics
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
# dmesg|grep -i acpi
BIOS-e820: 00000000bffe0000 - 00000000bffe3000 (ACPI NVS)
BIOS-e820: 00000000bffe3000 - 00000000bfff0000 (ACPI data)
ACPI: RSDP 00000000000f83d0 00024 (v02 RS780 )
ACPI: XSDT 00000000bffe3080 0004C (v01 RS780 AWRDACPI 42302E31 AWRD
00000000)
ACPI: FACP 00000000bffea480 000F4 (v03 RS780 AWRDACPI 42302E31 AWRD
00000000)
ACPI: DSDT 00000000bffe3200 0724B (v01 RS780 AWRDACPI 00001000 MSFT
03000000)
ACPI: FACS 00000000bffe0000 00040
ACPI: SSDT 00000000bffea640 0095E (v01 PTLTD POWERNOW 00000001 LTP
00000001)
ACPI: HPET 00000000bffeafc0 00038 (v01 RS780 AWRDACPI 42302E31 AWRD
00000098)
ACPI: MCFG 00000000bffeb000 0003C (v01 RS780 AWRDACPI 42302E31 AWRD
00000000)
ACPI: APIC 00000000bffea580 00084 (v01 RS780 AWRDACPI 42302E31 AWRD
00000000)
ACPI: Local APIC address 0xfee00000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10b9a201 base: 0xfed00000
ACPI: Core revision 20091214
ACPI: bus type pci registered
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci_root PNP0A03:00: ignoring host bridge windows from ACPI; boot with
"pci=use_crs" to use them
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
ACPI Warning for \_TZ_.THRM._PSL: Return Package type mismatch at index
0 - found [NULL Object Descriptor], expected Reference
(20091214/nspredef-1040)
ACPI: Expecting a [Reference] package element, found type 0
ACPI: Invalid passive threshold
ACPI: Thermal Zone [THRM] (40 C)
ACPI: Power Button [PWRB]
ACPI: Power Button [PWRF]
ACPI: Fan [FAN] (on)
ACPI: I/O resource f71882fg [0x220-0x227] conflicts with ACPI region
IP__ [0x225-0x226]
ACPI: If an ACPI driver is available for this device, you should use it
instead of the native driver
(etc)
Udo
next reply other threads:[~2010-03-01 19:13 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-03-01 18:21 Udo van den Heuvel [this message]
2010-03-03 5:37 ` [lm-sensors] 2.6.33 on jetway nc81-lf board Andrew Morton
2010-03-03 5:37 ` Andrew Morton
2010-03-04 9:17 ` [lm-sensors] " Andre Prendel
2010-03-04 9:17 ` Andre Prendel
2010-03-04 14:34 ` Udo van den Heuvel
2010-03-04 14:34 ` Udo van den Heuvel
2010-03-05 2:09 ` Robert Hancock
2010-03-05 2:09 ` Robert Hancock
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B8C0598.2060000@xs4all.nl \
--to=udovdh@xs4all.nl \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.