* Linux on Au1350 using Yamon
@ 2010-05-13 5:28 ` Sanjay Kumar
0 siblings, 0 replies; 9+ messages in thread
From: Sanjay Kumar @ 2010-05-13 5:28 UTC (permalink / raw)
To: linux-mips
Hi ,
We are trying to port Linux on Au1350 Board. We are using Linux port of db1300 board. We have Yamon bootloader running on the board.
The board does not have Ethernet port ,so we are loading Linux and rootfile system thru serial port and running using "go" command from Yamon. Linux is working as expected.
We have BDI3000 debugger and was wondering if it is possible to load the kernel and rootfile system to SDRAM using the debugger and execute it using Yamon ?
I tried this but could not succeed . Below are the steps I tried :
1. Start Yamon using BDI.
2. Halt the CPU and dump the kernel and rootfile system to SDRAM at free memory location ( 0x80093bf8 as per Yamon prompt).
3. We observed TLB exception while loading .
"
Au1350>load 0x80093bf8 vmlinux-rmi.srec srec
Loading vmlinux-rmi.srec , please wait ....
# TLB exception raised
"
If we reset the target using BDI reset command and then load is successful.
4. After load we gave go command from BDI to start the yamon.
5. Memory dump from Yamon shows correct download , but when I gave go command followed by load address its giving exception.
"
YAMON> go 0x80093bf8
* Exception (user) : TLB (load or instruction fetch) *
CAUSE = 0x00808008 STATUS = 0x00000002
EPC = 0x8010201c ERROREPC = 0xb02f52ce
BADVADDR = 0x000008c2
$ 0(zr):0x00000000 $ 8(t0):0x00000000 $16(s0):0x00000000 $24(t8):0x00000000
$ 1(at):0x00000000 $ 9(t1):0x00000000 $17(s1):0x00000000 $25(t9):0x00000000
$ 2(v0):0x00000000 $10(t2):0x00000000 $18(s2):0x00000000 $26(k0):0x00000000
$ 3(v1):0x00000000 $11(t3):0x00000000 $19(s3):0x00000000 $27(k1):0x00000000
$ 4(a0):0x00000001 $12(t4):0x00000000 $20(s4):0x00000000 $28(gp):0x00000000
$ 5(a1):0x80087340 $13(t5):0x00000000 $21(s5):0x00000000 $29(sp):0x80093be8
$ 6(a2):0x00000000 $14(t6):0x00000000 $22(s6):0x00000000 $30(s8):0x80093be8
$ 7(a3):0x10000000 $15(t7):0x00000000 $23(s7):0x00000000 $31(ra):0x8002f608
YAMON>
"
Any suggestion will be highly appreciated.
Thanks
Sanjay
^ permalink raw reply [flat|nested] 9+ messages in thread* Linux on Au1350 using Yamon @ 2010-05-13 5:28 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-13 5:28 UTC (permalink / raw) To: linux-mips Hi , We are trying to port Linux on Au1350 Board. We are using Linux port of db1300 board. We have Yamon bootloader running on the board. The board does not have Ethernet port ,so we are loading Linux and rootfile system thru serial port and running using "go" command from Yamon. Linux is working as expected. We have BDI3000 debugger and was wondering if it is possible to load the kernel and rootfile system to SDRAM using the debugger and execute it using Yamon ? I tried this but could not succeed . Below are the steps I tried : 1. Start Yamon using BDI. 2. Halt the CPU and dump the kernel and rootfile system to SDRAM at free memory location ( 0x80093bf8 as per Yamon prompt). 3. We observed TLB exception while loading . " Au1350>load 0x80093bf8 vmlinux-rmi.srec srec Loading vmlinux-rmi.srec , please wait .... # TLB exception raised " If we reset the target using BDI reset command and then load is successful. 4. After load we gave go command from BDI to start the yamon. 5. Memory dump from Yamon shows correct download , but when I gave go command followed by load address its giving exception. " YAMON> go 0x80093bf8 * Exception (user) : TLB (load or instruction fetch) * CAUSE = 0x00808008 STATUS = 0x00000002 EPC = 0x8010201c ERROREPC = 0xb02f52ce BADVADDR = 0x000008c2 $ 0(zr):0x00000000 $ 8(t0):0x00000000 $16(s0):0x00000000 $24(t8):0x00000000 $ 1(at):0x00000000 $ 9(t1):0x00000000 $17(s1):0x00000000 $25(t9):0x00000000 $ 2(v0):0x00000000 $10(t2):0x00000000 $18(s2):0x00000000 $26(k0):0x00000000 $ 3(v1):0x00000000 $11(t3):0x00000000 $19(s3):0x00000000 $27(k1):0x00000000 $ 4(a0):0x00000001 $12(t4):0x00000000 $20(s4):0x00000000 $28(gp):0x00000000 $ 5(a1):0x80087340 $13(t5):0x00000000 $21(s5):0x00000000 $29(sp):0x80093be8 $ 6(a2):0x00000000 $14(t6):0x00000000 $22(s6):0x00000000 $30(s8):0x80093be8 $ 7(a3):0x10000000 $15(t7):0x00000000 $23(s7):0x00000000 $31(ra):0x8002f608 YAMON> " Any suggestion will be highly appreciated. Thanks Sanjay ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Linux on Au1350 using Yamon 2010-05-13 5:28 ` Sanjay Kumar (?) @ 2010-05-13 6:03 ` tiejun.chen 2010-05-13 6:49 ` Sanjay Kumar 2010-05-17 11:23 ` Sanjay Kumar -1 siblings, 2 replies; 9+ messages in thread From: tiejun.chen @ 2010-05-13 6:03 UTC (permalink / raw) To: Sanjay Kumar; +Cc: linux-mips Sanjay Kumar wrote: > Hi , > > We are trying to port Linux on Au1350 Board. We are using Linux port of db1300 board. We have Yamon bootloader running on the board. > > The board does not have Ethernet port ,so we are loading Linux and rootfile system thru serial port and running using "go" command from Yamon. Linux is working as expected. > > We have BDI3000 debugger and was wondering if it is possible to load the kernel and rootfile system to SDRAM using the debugger and execute it using Yamon ? > > > > I tried this but could not succeed . Below are the steps I tried : > > > > 1. Start Yamon using BDI. > > 2. Halt the CPU and dump the kernel and rootfile system to SDRAM at free memory location ( 0x80093bf8 as per Yamon prompt). > > 3. We observed TLB exception while loading . > > " > > Au1350>load 0x80093bf8 vmlinux-rmi.srec srec I'm not sure if BDI can load .srec file, unless it can parse srec syntax. > > Loading vmlinux-rmi.srec , please wait .... > > # TLB exception raised > > " > > If we reset the target using BDI reset command and then load is successful. > > > > 4. After load we gave go command from BDI to start the yamon. > > 5. Memory dump from Yamon shows correct download , but when I gave go command followed by load address its giving exception. > You should dump memory to compare vmlinux directly, not vmlinux.srec. .srec did wrapper on vmlinux. > " > > YAMON> go 0x80093bf8 And this is not correct start address since the start address is not same as load address on YAMON. Firstly you should get the offset from entry address to load address on vmlinux. You can refer to Makefile and System.map. Then add this offset on your real load address to get your real entry address. Best Regards Tiejun > > > > * Exception (user) : TLB (load or instruction fetch) * > > > > CAUSE = 0x00808008 STATUS = 0x00000002 > > EPC = 0x8010201c ERROREPC = 0xb02f52ce > > BADVADDR = 0x000008c2 > > > > $ 0(zr):0x00000000 $ 8(t0):0x00000000 $16(s0):0x00000000 $24(t8):0x00000000 > > $ 1(at):0x00000000 $ 9(t1):0x00000000 $17(s1):0x00000000 $25(t9):0x00000000 > > $ 2(v0):0x00000000 $10(t2):0x00000000 $18(s2):0x00000000 $26(k0):0x00000000 > > $ 3(v1):0x00000000 $11(t3):0x00000000 $19(s3):0x00000000 $27(k1):0x00000000 > > $ 4(a0):0x00000001 $12(t4):0x00000000 $20(s4):0x00000000 $28(gp):0x00000000 > > $ 5(a1):0x80087340 $13(t5):0x00000000 $21(s5):0x00000000 $29(sp):0x80093be8 > > $ 6(a2):0x00000000 $14(t6):0x00000000 $22(s6):0x00000000 $30(s8):0x80093be8 > > $ 7(a3):0x10000000 $15(t7):0x00000000 $23(s7):0x00000000 $31(ra):0x8002f608 > > > > YAMON> > > " > > > > Any suggestion will be highly appreciated. > > > > Thanks > > Sanjay > > ^ permalink raw reply [flat|nested] 9+ messages in thread
* RE: Linux on Au1350 using Yamon @ 2010-05-13 6:49 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-13 6:49 UTC (permalink / raw) To: tiejun.chen; +Cc: linux-mips Hi Tiejun, Thanks for the inputs , I will look into this and let you know the outcome. -Sanjay -----Original Message----- From: tiejun.chen [mailto:tiejun.chen@windriver.com] Sent: Thu 5/13/2010 3:03 PM To: Sanjay Kumar Cc: linux-mips@linux-mips.org Subject: Re: Linux on Au1350 using Yamon Sanjay Kumar wrote: > Hi , > > We are trying to port Linux on Au1350 Board. We are using Linux port of db1300 board. We have Yamon bootloader running on the board. > > The board does not have Ethernet port ,so we are loading Linux and rootfile system thru serial port and running using "go" command from Yamon. Linux is working as expected. > > We have BDI3000 debugger and was wondering if it is possible to load the kernel and rootfile system to SDRAM using the debugger and execute it using Yamon ? > > > > I tried this but could not succeed . Below are the steps I tried : > > > > 1. Start Yamon using BDI. > > 2. Halt the CPU and dump the kernel and rootfile system to SDRAM at free memory location ( 0x80093bf8 as per Yamon prompt). > > 3. We observed TLB exception while loading . > > " > > Au1350>load 0x80093bf8 vmlinux-rmi.srec srec I'm not sure if BDI can load .srec file, unless it can parse srec syntax. > > Loading vmlinux-rmi.srec , please wait .... > > # TLB exception raised > > " > > If we reset the target using BDI reset command and then load is successful. > > > > 4. After load we gave go command from BDI to start the yamon. > > 5. Memory dump from Yamon shows correct download , but when I gave go command followed by load address its giving exception. > You should dump memory to compare vmlinux directly, not vmlinux.srec. .srec did wrapper on vmlinux. > " > > YAMON> go 0x80093bf8 And this is not correct start address since the start address is not same as load address on YAMON. Firstly you should get the offset from entry address to load address on vmlinux. You can refer to Makefile and System.map. Then add this offset on your real load address to get your real entry address. Best Regards Tiejun > > > > * Exception (user) : TLB (load or instruction fetch) * > > > > CAUSE = 0x00808008 STATUS = 0x00000002 > > EPC = 0x8010201c ERROREPC = 0xb02f52ce > > BADVADDR = 0x000008c2 > > > > $ 0(zr):0x00000000 $ 8(t0):0x00000000 $16(s0):0x00000000 $24(t8):0x00000000 > > $ 1(at):0x00000000 $ 9(t1):0x00000000 $17(s1):0x00000000 $25(t9):0x00000000 > > $ 2(v0):0x00000000 $10(t2):0x00000000 $18(s2):0x00000000 $26(k0):0x00000000 > > $ 3(v1):0x00000000 $11(t3):0x00000000 $19(s3):0x00000000 $27(k1):0x00000000 > > $ 4(a0):0x00000001 $12(t4):0x00000000 $20(s4):0x00000000 $28(gp):0x00000000 > > $ 5(a1):0x80087340 $13(t5):0x00000000 $21(s5):0x00000000 $29(sp):0x80093be8 > > $ 6(a2):0x00000000 $14(t6):0x00000000 $22(s6):0x00000000 $30(s8):0x80093be8 > > $ 7(a3):0x10000000 $15(t7):0x00000000 $23(s7):0x00000000 $31(ra):0x8002f608 > > > > YAMON> > > " > > > > Any suggestion will be highly appreciated. > > > > Thanks > > Sanjay > > ^ permalink raw reply [flat|nested] 9+ messages in thread
* RE: Linux on Au1350 using Yamon @ 2010-05-13 6:49 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-13 6:49 UTC (permalink / raw) To: tiejun.chen; +Cc: linux-mips Hi Tiejun, Thanks for the inputs , I will look into this and let you know the outcome. -Sanjay -----Original Message----- From: tiejun.chen [mailto:tiejun.chen@windriver.com] Sent: Thu 5/13/2010 3:03 PM To: Sanjay Kumar Cc: linux-mips@linux-mips.org Subject: Re: Linux on Au1350 using Yamon Sanjay Kumar wrote: > Hi , > > We are trying to port Linux on Au1350 Board. We are using Linux port of db1300 board. We have Yamon bootloader running on the board. > > The board does not have Ethernet port ,so we are loading Linux and rootfile system thru serial port and running using "go" command from Yamon. Linux is working as expected. > > We have BDI3000 debugger and was wondering if it is possible to load the kernel and rootfile system to SDRAM using the debugger and execute it using Yamon ? > > > > I tried this but could not succeed . Below are the steps I tried : > > > > 1. Start Yamon using BDI. > > 2. Halt the CPU and dump the kernel and rootfile system to SDRAM at free memory location ( 0x80093bf8 as per Yamon prompt). > > 3. We observed TLB exception while loading . > > " > > Au1350>load 0x80093bf8 vmlinux-rmi.srec srec I'm not sure if BDI can load .srec file, unless it can parse srec syntax. > > Loading vmlinux-rmi.srec , please wait .... > > # TLB exception raised > > " > > If we reset the target using BDI reset command and then load is successful. > > > > 4. After load we gave go command from BDI to start the yamon. > > 5. Memory dump from Yamon shows correct download , but when I gave go command followed by load address its giving exception. > You should dump memory to compare vmlinux directly, not vmlinux.srec. .srec did wrapper on vmlinux. > " > > YAMON> go 0x80093bf8 And this is not correct start address since the start address is not same as load address on YAMON. Firstly you should get the offset from entry address to load address on vmlinux. You can refer to Makefile and System.map. Then add this offset on your real load address to get your real entry address. Best Regards Tiejun > > > > * Exception (user) : TLB (load or instruction fetch) * > > > > CAUSE = 0x00808008 STATUS = 0x00000002 > > EPC = 0x8010201c ERROREPC = 0xb02f52ce > > BADVADDR = 0x000008c2 > > > > $ 0(zr):0x00000000 $ 8(t0):0x00000000 $16(s0):0x00000000 $24(t8):0x00000000 > > $ 1(at):0x00000000 $ 9(t1):0x00000000 $17(s1):0x00000000 $25(t9):0x00000000 > > $ 2(v0):0x00000000 $10(t2):0x00000000 $18(s2):0x00000000 $26(k0):0x00000000 > > $ 3(v1):0x00000000 $11(t3):0x00000000 $19(s3):0x00000000 $27(k1):0x00000000 > > $ 4(a0):0x00000001 $12(t4):0x00000000 $20(s4):0x00000000 $28(gp):0x00000000 > > $ 5(a1):0x80087340 $13(t5):0x00000000 $21(s5):0x00000000 $29(sp):0x80093be8 > > $ 6(a2):0x00000000 $14(t6):0x00000000 $22(s6):0x00000000 $30(s8):0x80093be8 > > $ 7(a3):0x10000000 $15(t7):0x00000000 $23(s7):0x00000000 $31(ra):0x8002f608 > > > > YAMON> > > " > > > > Any suggestion will be highly appreciated. > > > > Thanks > > Sanjay > > ^ permalink raw reply [flat|nested] 9+ messages in thread
* USB device not detected in Au1350 @ 2010-05-17 11:23 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-17 11:23 UTC (permalink / raw) To: linux-mips Hi , We are porting Linux to Au1350 board . We are using Yamon bootloader and Linux source code (2.6.29) of DB1300 board. Kenel is booting successfully on our board.Currently we are using initramfs. We have enabled USB support in the configuration file but USB device is not detected , however boot message shows that the USB drivers are loaded properly.It is detecting root hub and ports. After inserting USB device (pen drive) a device file shall be created in /dev ( like sda , sdb etc.) but its not happening in my case. /proc/devices has the following block devices: 1 ramdisk 259 blkext 7 loop 8 sd 11 sr 65 sd 66 sd 67 sd 68 sd 69 sd 70 sd 71 sd 128 sd 129 sd 130 sd 131 sd 132 sd 133 sd 134 sd 135 sd 179 mmc When tried to create block using mknod for the major nos mentioned (mknod /dev/sda b 135 0) , while mounting it says "/dev/sda" is not a valid block device. Similar result for other block devices too. /sys/block has following deveices , which are different from /proc/devices /sys/block# ls loop0 loop3 loop6 ram1 ram12 ram15 ram4 ram7 loop1 loop4 loop7 ram10 ram13 ram2 ram5 ram8 loop2 loop5 ram0 ram11 ram14 ram3 ram6 ram9 /proc/bus/usb/devices has the following: root@db1300:/proc/bus/usb# cat devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd S: Product=Au13xx EHCI S: SerialNumber=au13xx-ehci.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms Any suggestion where it could be going wrong ? Below is the boot message and kernel configuration I'm using. ========================================================================================================== Below is the boot message related to USB: Linux version 2.6.29.4-rmi-126-DB1300 (sanjayk@ubuntu) (gcc version 4.2.4) #0 Wed May 12 16:25:25 IST 2010 console [early0] enabled CPU revision is: 800c8001 (Au13xx) (PRId 800c8001) @ 396.00 MHz RMI DBAu1300 Development Board Determined physical RAM map: memory: 01800000 @ 00000000 (usable) memory: 0c800000 @ 01800000 (reserved) memory: 02000000 @ 0e000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,115200 video=au1200fb:panel:bs Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes PID hash table entries: 1024 (order: 10, 4096 bytes) Alchemy clocksource installed Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 42308k/57344k available (3360k kernel code, 14760k reserved, 796k data, 7008k init, 0k highmem) Calibrating delay loop... 395.67 BogoMIPS (lpj=1978368) Mount-cache hash table entries: 512 net_namespace: 296 bytes NET: Registered protocol family 16 Hooking cpu_wait bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Creating sysfs entry for board Alchemy MEMPOOL initializing Alchemy MEMPOOL registered at major 235 Available memory pools: LCD: 40 MB @ phys 0x01800000, free BSA: 64 MB @ phys 0x04000000, free MPE: 32 MB @ phys 0x08000000, free OGL: 64 MB @ phys 0x0a000000, free squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 83 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered au1200fb: LCD controller driver for AU1200 processors Returning LCD switch setting 0 au1200fb: Panel 0 Samsung 800x480 au1200fb: Win 2 0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx Panel(Samsung 800x480), 800x480 Returning LCD switch setting 0 IRQ 99/lcd: IRQF_DISABLED is not guaranteed on shared IRQs au1200fb: Allocating fb0: 800x480@16 bpp Console: switching to colour frame buffer device 100x30 au1200fb: Allocating fb1: 800x480@16 bpp au1200fb: Allocating fb2: 800x480@32 bpp au1200fb: Allocating fb3: 800x480@16 bpp Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.9: ttyS0 at MMIO 0x10102000 (irq = 33) is a 8250 console handover: boot [early0] -> real [ttyS0] brd: module loaded loop: module loaded smsc911x: Driver version 2008-10-21. MAEBE: physAddr 08000000, physSize 02000000 Au12XX MAEBE driver registered Sucessfully v1.0 Au13XX MAEBSA driver registered Sucessfully v1.0 Au13XX MAEMPE driver registered Sucessfully v1.0 mae_dma: pri0 45617238, pri1 09000000 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci->regs = b4020010 au13xx-ehci au13xx-ehci.0: Au13xx EHCI au13xx-ehci au13xx-ehci.0: new USB bus registered, assigned bus number 1 au13xx-ehci au13xx-ehci.0: irq 98, io mem 0x14020000 au13xx-ehci au13xx-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Au13xx EHCI usb usb1: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd usb usb1: SerialNumber: au13xx-ehci.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual Probing for MMC Probing for MMC mmc0 au1xxx-mmc: MMC Controller 0 set up at B0600000 (mode=dma) usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver oprofile: using timer interrupt. RMI Linux 271 db1300 ttyS0 db1300 login: ======================================================================================================================================= Kernel Configuration: # # Automatically generated make config: don't edit # Linux kernel version: 2.6.29.4-rmi-126 # Mon May 17 09:46:07 2010 # CONFIG_MIPS=y # # Machine selection # CONFIG_MACH_ALCHEMY=y # CONFIG_BASLER_EXCITE is not set # CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set # CONFIG_LASAT is not set # CONFIG_LEMOTE_FULONG is not set # CONFIG_MIPS_MALTA is not set # CONFIG_MIPS_SIM is not set # CONFIG_NEC_MARKEINS is not set # CONFIG_MACH_VR41XX is not set # CONFIG_NXP_STB220 is not set # CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set # CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set # CONFIG_SIBYTE_CRHINE is not set # CONFIG_SIBYTE_CARMEL is not set # CONFIG_SIBYTE_CRHONE is not set # CONFIG_SIBYTE_RHONE is not set # CONFIG_SIBYTE_SWARM is not set # CONFIG_SIBYTE_LITTLESUR is not set # CONFIG_SIBYTE_SENTOSA is not set # CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set # CONFIG_MACH_TX39XX is not set # CONFIG_MACH_TX49XX is not set # CONFIG_MIKROTIK_RB532 is not set # CONFIG_WR_PPMC is not set # CONFIG_CAVIUM_OCTEON_SIMULATOR is not set # CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set # CONFIG_MIPS_MTX1 is not set # CONFIG_MIPS_BOSPORUS is not set # CONFIG_MIPS_DB1000 is not set # CONFIG_MIPS_DB1100 is not set # CONFIG_MIPS_DB1200 is not set # CONFIG_MIPS_HMP10 is not set # CONFIG_MIPS_DB1500 is not set # CONFIG_MIPS_DB1550 is not set CONFIG_MIPS_DB1300=y # CONFIG_MIPS_MIRAGE is not set # CONFIG_MIPS_PB1000 is not set # CONFIG_MIPS_PB1100 is not set # CONFIG_MIPS_PB1200 is not set # CONFIG_MIPS_PB1500 is not set # CONFIG_MIPS_PB1550 is not set # CONFIG_MIPS_XXS1500 is not set CONFIG_SOC_AU13XX=y CONFIG_SOC_AU1X00=y CONFIG_AU_GPIO_INT_CNTLR=y CONFIG_AU_MEMPOOL=y CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_OMIT_FRAME_POINTER=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_CEVT_R4K_LIB=y CONFIG_CSRC_R4K_LIB=y CONFIG_DMA_COHERENT=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y # CONFIG_HOTPLUG_CPU is not set # CONFIG_NO_IOPORT is not set # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y CONFIG_IRQ_CPU=y CONFIG_MIPS_L1_CACHE_SHIFT=5 # # CPU selection # # CONFIG_CPU_LOONGSON2 is not set CONFIG_CPU_MIPS32_R1=y # CONFIG_CPU_MIPS32_R2 is not set # CONFIG_CPU_MIPS64_R1 is not set # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set # CONFIG_CPU_VR41XX is not set # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set # CONFIG_CPU_R5000 is not set # CONFIG_CPU_R5432 is not set # CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set # CONFIG_CPU_R10000 is not set # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set # CONFIG_CPU_CAVIUM_OCTEON is not set CONFIG_SYS_HAS_CPU_MIPS32_R1=y CONFIG_CPU_MIPS32=y CONFIG_CPU_MIPSR1=y CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y CONFIG_HARDWARE_WATCHPOINTS=y # # Kernel type # CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT_DISABLED=y # CONFIG_MIPS_MT_SMP is not set # CONFIG_MIPS_MT_SMTC is not set CONFIG_64BIT_PHYS_ADDR=y CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y # CONFIG_HIGHMEM is not set CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_SYS_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y CONFIG_UNEVICTABLE_LRU=y # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set CONFIG_HZ_100=y # CONFIG_HZ_128 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_256 is not set # CONFIG_HZ_1000 is not set # CONFIG_HZ_1024 is not set CONFIG_SYS_SUPPORTS_ARBIT_HZ=y CONFIG_HZ=100 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set # CONFIG_KEXEC is not set CONFIG_SECCOMP=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_LOCALVERSION="-DB1300" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set # # RCU Subsystem # CONFIG_CLASSIC_RCU=y # CONFIG_TREE_RCU is not set # CONFIG_PREEMPT_RCU is not set # CONFIG_TREE_RCU_TRACE is not set # CONFIG_PREEMPT_RCU_TRACE is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_GROUP_SCHED is not set # CONFIG_CGROUPS is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set # CONFIG_NAMESPACES is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="/host/Project/AVN/Misc/kd/rootfs-tiny" CONFIG_INITRAMFS_ROOT_UID=0 CONFIG_INITRAMFS_ROOT_GID=0 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_PCSPKR_PLATFORM=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y CONFIG_MARKERS=y CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_DEADLINE is not set # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_PROBE_INITRD_HEADER is not set CONFIG_FREEZER=y # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # # CONFIG_ARCH_SUPPORTS_MSI is not set CONFIG_MMU=y # CONFIG_PCCARD is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_TRAD_SIGNALS=y # # Power management options # CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_PM=y # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y CONFIG_SUSPEND_FREEZER=y # CONFIG_APM_EMULATION is not set CONFIG_NET=y # # Networking options # CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set # CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set # CONFIG_PHONET is not set # CONFIG_WIRELESS is not set # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set # # Device Drivers # # # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y CONFIG_FIRMWARE_IN_KERNEL=y CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # CONFIG_BLK_DEV_HD is not set # CONFIG_LBA_NAND is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y CONFIG_SCSI_DMA=y CONFIG_SCSI_TGT=y # CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set CONFIG_SCSI_SCAN_ASYNC=y CONFIG_SCSI_WAIT_SCAN=m # # SCSI Transports # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_LIBFC is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # CONFIG_VETH is not set CONFIG_PHYLIB=y # # MII PHY device drivers # # CONFIG_MARVELL_PHY is not set # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set # CONFIG_CICADA_PHY is not set # CONFIG_VITESSE_PHY is not set # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_AX88796 is not set # CONFIG_MIPS_AU1X00_ENET is not set # CONFIG_SMC91X is not set # CONFIG_DM9000 is not set CONFIG_SMSC911X=y # CONFIG_SMSC9210 is not set # CONFIG_DNET is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # # Wireless LAN # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set # CONFIG_IWLWIFI_LEDS is not set # # Enable WiMAX (Networking options) to see the WiMAX drivers # # # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set # # Userland interfaces # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set # # Hardware I/O ports # CONFIG_SERIO=y # CONFIG_SERIO_I8042 is not set CONFIG_SERIO_SERPORT=y CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=y # CONFIG_GAMEPORT is not set # # Character devices # CONFIG_VT=y CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set CONFIG_SERIAL_8250_AU1X00=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set # CONFIG_HW_RANDOM is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # # CONFIG_SSB is not set # # Multifunction device drivers # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set # # Multimedia devices # # # Multimedia core support # # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set # CONFIG_VIDEO_MEDIA is not set # # Multimedia drivers # # CONFIG_DAB is not set # # Alchemy MAE # CONFIG_AU13XX_MAE2=y CONFIG_ALCHEMY_MAE_ITE=y CONFIG_ALCHEMY_MAE_BSA=y CONFIG_ALCHEMY_MAE_MPE=y # # Graphics support # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set # CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set # CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # # Frame buffer hardware drivers # # CONFIG_FB_S1D13XXX is not set CONFIG_FB_AU1200=y # CONFIG_FB_VIRTUAL is not set # CONFIG_FB_METRONOME is not set # CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set # CONFIG_LOGO_LINUX_CLUT224 is not set CONFIG_LOGO_RMI_ALCHEMY_VGA16=y # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # # USB Input Devices # CONFIG_USB_HID=y # CONFIG_HID_PID is not set # CONFIG_USB_HIDDEV is not set # # Special HID drivers # CONFIG_HID_COMPAT=y # CONFIG_HID_A4TECH is not set # CONFIG_HID_APPLE is not set # CONFIG_HID_BELKIN is not set # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_GYRATION is not set # CONFIG_HID_LOGITECH is not set # CONFIG_HID_MICROSOFT is not set # CONFIG_HID_MONTEREY is not set # CONFIG_HID_NTRIG is not set # CONFIG_HID_PANTHERLORD is not set # CONFIG_HID_PETALYNX is not set # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set # CONFIG_GREENASIA_FF is not set # CONFIG_HID_TOPSEED is not set # CONFIG_THRUSTMASTER_FF is not set # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y CONFIG_USB_DEBUG=y CONFIG_USB_ANNOUNCE_NEW_DEVICES=y # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set # CONFIG_USB_MON is not set # CONFIG_USB_WUSB is not set # CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_OHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_HWA_HCD is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set # CONFIG_USB_WDM is not set # CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # # see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y CONFIG_USB_STORAGE_DEBUG=y # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y # # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # # USB port drivers # # CONFIG_USB_SERIAL is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set # CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_BERRY_CHARGE is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set # # OTG and related infrastructure # CONFIG_MMC=y CONFIG_MMC_DEBUG=y CONFIG_MMC_UNSAFE_RESUME=y # # MMC/SD/SDIO Card Drivers # CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set # CONFIG_MMC_TEST is not set # # MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set CONFIG_MMC_AU1X=y # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set CONFIG_RTC_LIB=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y # CONFIG_EXT2_FS_SECURITY is not set # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set CONFIG_CONFIGFS_FS=m CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_ECRYPT_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set CONFIG_CRAMFS=y CONFIG_SQUASHFS=y # CONFIG_SQUASHFS_EMBEDDED is not set CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3 # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y # CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y # CONFIG_DLM is not set # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_STACKTRACE=y # CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_SYSCTL_SYSCALL_CHECK is not set CONFIG_NOP_TRACER=y CONFIG_RING_BUFFER=y CONFIG_TRACING=y # # Tracers # CONFIG_DYNAMIC_PRINTK_DEBUG=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="console=ttyS0,115200" # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # # CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_TEST is not set # # Authenticated Encryption with Associated Data # # CONFIG_CRYPTO_CCM is not set # CONFIG_CRYPTO_GCM is not set # CONFIG_CRYPTO_SEQIV is not set # # Block modes # CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_CTR is not set # CONFIG_CRYPTO_CTS is not set CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_LRW=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_XTS is not set # # Hash modes # CONFIG_CRYPTO_HMAC=m CONFIG_CRYPTO_XCBC=m # # Digest # CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_MICHAEL_MIC=m # CONFIG_CRYPTO_RMD128 is not set # CONFIG_CRYPTO_RMD160 is not set # CONFIG_CRYPTO_RMD256 is not set # CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_WP512=m # # Ciphers # CONFIG_CRYPTO_AES=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_DES=y CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m # CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # # Compression # CONFIG_CRYPTO_DEFLATE=m # CONFIG_CRYPTO_LZO is not set # # Random Number Generation # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # # Library routines # CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set CONFIG_CRC_ITU_T=m CONFIG_CRC32=y # CONFIG_CRC7 is not set CONFIG_LIBCRC32C=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y ==================================================================================================================== Thanks Sanjay ^ permalink raw reply [flat|nested] 9+ messages in thread
* USB device not detected in Au1350 @ 2010-05-17 11:23 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-17 11:23 UTC (permalink / raw) To: linux-mips Hi , We are porting Linux to Au1350 board . We are using Yamon bootloader and Linux source code (2.6.29) of DB1300 board. Kenel is booting successfully on our board.Currently we are using initramfs. We have enabled USB support in the configuration file but USB device is not detected , however boot message shows that the USB drivers are loaded properly.It is detecting root hub and ports. After inserting USB device (pen drive) a device file shall be created in /dev ( like sda , sdb etc.) but its not happening in my case. /proc/devices has the following block devices: 1 ramdisk 259 blkext 7 loop 8 sd 11 sr 65 sd 66 sd 67 sd 68 sd 69 sd 70 sd 71 sd 128 sd 129 sd 130 sd 131 sd 132 sd 133 sd 134 sd 135 sd 179 mmc When tried to create block using mknod for the major nos mentioned (mknod /dev/sda b 135 0) , while mounting it says "/dev/sda" is not a valid block device. Similar result for other block devices too. /sys/block has following deveices , which are different from /proc/devices /sys/block# ls loop0 loop3 loop6 ram1 ram12 ram15 ram4 ram7 loop1 loop4 loop7 ram10 ram13 ram2 ram5 ram8 loop2 loop5 ram0 ram11 ram14 ram3 ram6 ram9 /proc/bus/usb/devices has the following: root@db1300:/proc/bus/usb# cat devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd S: Product=Au13xx EHCI S: SerialNumber=au13xx-ehci.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms Any suggestion where it could be going wrong ? Below is the boot message and kernel configuration I'm using. ========================================================================================================== Below is the boot message related to USB: Linux version 2.6.29.4-rmi-126-DB1300 (sanjayk@ubuntu) (gcc version 4.2.4) #0 Wed May 12 16:25:25 IST 2010 console [early0] enabled CPU revision is: 800c8001 (Au13xx) (PRId 800c8001) @ 396.00 MHz RMI DBAu1300 Development Board Determined physical RAM map: memory: 01800000 @ 00000000 (usable) memory: 0c800000 @ 01800000 (reserved) memory: 02000000 @ 0e000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,115200 video=au1200fb:panel:bs Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes PID hash table entries: 1024 (order: 10, 4096 bytes) Alchemy clocksource installed Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 42308k/57344k available (3360k kernel code, 14760k reserved, 796k data, 7008k init, 0k highmem) Calibrating delay loop... 395.67 BogoMIPS (lpj=1978368) Mount-cache hash table entries: 512 net_namespace: 296 bytes NET: Registered protocol family 16 Hooking cpu_wait bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Creating sysfs entry for board Alchemy MEMPOOL initializing Alchemy MEMPOOL registered at major 235 Available memory pools: LCD: 40 MB @ phys 0x01800000, free BSA: 64 MB @ phys 0x04000000, free MPE: 32 MB @ phys 0x08000000, free OGL: 64 MB @ phys 0x0a000000, free squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 83 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered au1200fb: LCD controller driver for AU1200 processors Returning LCD switch setting 0 au1200fb: Panel 0 Samsung 800x480 au1200fb: Win 2 0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx Panel(Samsung 800x480), 800x480 Returning LCD switch setting 0 IRQ 99/lcd: IRQF_DISABLED is not guaranteed on shared IRQs au1200fb: Allocating fb0: 800x480@16 bpp Console: switching to colour frame buffer device 100x30 au1200fb: Allocating fb1: 800x480@16 bpp au1200fb: Allocating fb2: 800x480@32 bpp au1200fb: Allocating fb3: 800x480@16 bpp Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.9: ttyS0 at MMIO 0x10102000 (irq = 33) is a 8250 console handover: boot [early0] -> real [ttyS0] brd: module loaded loop: module loaded smsc911x: Driver version 2008-10-21. MAEBE: physAddr 08000000, physSize 02000000 Au12XX MAEBE driver registered Sucessfully v1.0 Au13XX MAEBSA driver registered Sucessfully v1.0 Au13XX MAEMPE driver registered Sucessfully v1.0 mae_dma: pri0 45617238, pri1 09000000 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci->regs = b4020010 au13xx-ehci au13xx-ehci.0: Au13xx EHCI au13xx-ehci au13xx-ehci.0: new USB bus registered, assigned bus number 1 au13xx-ehci au13xx-ehci.0: irq 98, io mem 0x14020000 au13xx-ehci au13xx-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Au13xx EHCI usb usb1: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd usb usb1: SerialNumber: au13xx-ehci.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual Probing for MMC Probing for MMC mmc0 au1xxx-mmc: MMC Controller 0 set up at B0600000 (mode=dma) usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver oprofile: using timer interrupt. RMI Linux 271 db1300 ttyS0 db1300 login: ======================================================================================================================================= Kernel Configuration: # # Automatically generated make config: don't edit # Linux kernel version: 2.6.29.4-rmi-126 # Mon May 17 09:46:07 2010 # CONFIG_MIPS=y # # Machine selection # CONFIG_MACH_ALCHEMY=y # CONFIG_BASLER_EXCITE is not set # CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set # CONFIG_LASAT is not set # CONFIG_LEMOTE_FULONG is not set # CONFIG_MIPS_MALTA is not set # CONFIG_MIPS_SIM is not set # CONFIG_NEC_MARKEINS is not set # CONFIG_MACH_VR41XX is not set # CONFIG_NXP_STB220 is not set # CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set # CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set # CONFIG_SIBYTE_CRHINE is not set # CONFIG_SIBYTE_CARMEL is not set # CONFIG_SIBYTE_CRHONE is not set # CONFIG_SIBYTE_RHONE is not set # CONFIG_SIBYTE_SWARM is not set # CONFIG_SIBYTE_LITTLESUR is not set # CONFIG_SIBYTE_SENTOSA is not set # CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set # CONFIG_MACH_TX39XX is not set # CONFIG_MACH_TX49XX is not set # CONFIG_MIKROTIK_RB532 is not set # CONFIG_WR_PPMC is not set # CONFIG_CAVIUM_OCTEON_SIMULATOR is not set # CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set # CONFIG_MIPS_MTX1 is not set # CONFIG_MIPS_BOSPORUS is not set # CONFIG_MIPS_DB1000 is not set # CONFIG_MIPS_DB1100 is not set # CONFIG_MIPS_DB1200 is not set # CONFIG_MIPS_HMP10 is not set # CONFIG_MIPS_DB1500 is not set # CONFIG_MIPS_DB1550 is not set CONFIG_MIPS_DB1300=y # CONFIG_MIPS_MIRAGE is not set # CONFIG_MIPS_PB1000 is not set # CONFIG_MIPS_PB1100 is not set # CONFIG_MIPS_PB1200 is not set # CONFIG_MIPS_PB1500 is not set # CONFIG_MIPS_PB1550 is not set # CONFIG_MIPS_XXS1500 is not set CONFIG_SOC_AU13XX=y CONFIG_SOC_AU1X00=y CONFIG_AU_GPIO_INT_CNTLR=y CONFIG_AU_MEMPOOL=y CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_OMIT_FRAME_POINTER=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_CEVT_R4K_LIB=y CONFIG_CSRC_R4K_LIB=y CONFIG_DMA_COHERENT=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y # CONFIG_HOTPLUG_CPU is not set # CONFIG_NO_IOPORT is not set # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y CONFIG_IRQ_CPU=y CONFIG_MIPS_L1_CACHE_SHIFT=5 # # CPU selection # # CONFIG_CPU_LOONGSON2 is not set CONFIG_CPU_MIPS32_R1=y # CONFIG_CPU_MIPS32_R2 is not set # CONFIG_CPU_MIPS64_R1 is not set # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set # CONFIG_CPU_VR41XX is not set # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set # CONFIG_CPU_R5000 is not set # CONFIG_CPU_R5432 is not set # CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set # CONFIG_CPU_R10000 is not set # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set # CONFIG_CPU_CAVIUM_OCTEON is not set CONFIG_SYS_HAS_CPU_MIPS32_R1=y CONFIG_CPU_MIPS32=y CONFIG_CPU_MIPSR1=y CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y CONFIG_HARDWARE_WATCHPOINTS=y # # Kernel type # CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT_DISABLED=y # CONFIG_MIPS_MT_SMP is not set # CONFIG_MIPS_MT_SMTC is not set CONFIG_64BIT_PHYS_ADDR=y CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y # CONFIG_HIGHMEM is not set CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_SYS_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y CONFIG_UNEVICTABLE_LRU=y # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set CONFIG_HZ_100=y # CONFIG_HZ_128 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_256 is not set # CONFIG_HZ_1000 is not set # CONFIG_HZ_1024 is not set CONFIG_SYS_SUPPORTS_ARBIT_HZ=y CONFIG_HZ=100 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set # CONFIG_KEXEC is not set CONFIG_SECCOMP=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_LOCALVERSION="-DB1300" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set # # RCU Subsystem # CONFIG_CLASSIC_RCU=y # CONFIG_TREE_RCU is not set # CONFIG_PREEMPT_RCU is not set # CONFIG_TREE_RCU_TRACE is not set # CONFIG_PREEMPT_RCU_TRACE is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_GROUP_SCHED is not set # CONFIG_CGROUPS is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set # CONFIG_NAMESPACES is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="/host/Project/AVN/Misc/kd/rootfs-tiny" CONFIG_INITRAMFS_ROOT_UID=0 CONFIG_INITRAMFS_ROOT_GID=0 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_PCSPKR_PLATFORM=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y CONFIG_MARKERS=y CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_DEADLINE is not set # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_PROBE_INITRD_HEADER is not set CONFIG_FREEZER=y # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # # CONFIG_ARCH_SUPPORTS_MSI is not set CONFIG_MMU=y # CONFIG_PCCARD is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_TRAD_SIGNALS=y # # Power management options # CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_PM=y # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y CONFIG_SUSPEND_FREEZER=y # CONFIG_APM_EMULATION is not set CONFIG_NET=y # # Networking options # CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set # CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set # CONFIG_PHONET is not set # CONFIG_WIRELESS is not set # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set # # Device Drivers # # # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y CONFIG_FIRMWARE_IN_KERNEL=y CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # CONFIG_BLK_DEV_HD is not set # CONFIG_LBA_NAND is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y CONFIG_SCSI_DMA=y CONFIG_SCSI_TGT=y # CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set CONFIG_SCSI_SCAN_ASYNC=y CONFIG_SCSI_WAIT_SCAN=m # # SCSI Transports # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_LIBFC is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # CONFIG_VETH is not set CONFIG_PHYLIB=y # # MII PHY device drivers # # CONFIG_MARVELL_PHY is not set # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set # CONFIG_CICADA_PHY is not set # CONFIG_VITESSE_PHY is not set # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_AX88796 is not set # CONFIG_MIPS_AU1X00_ENET is not set # CONFIG_SMC91X is not set # CONFIG_DM9000 is not set CONFIG_SMSC911X=y # CONFIG_SMSC9210 is not set # CONFIG_DNET is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # # Wireless LAN # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set # CONFIG_IWLWIFI_LEDS is not set # # Enable WiMAX (Networking options) to see the WiMAX drivers # # # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set # # Userland interfaces # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set # # Hardware I/O ports # CONFIG_SERIO=y # CONFIG_SERIO_I8042 is not set CONFIG_SERIO_SERPORT=y CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=y # CONFIG_GAMEPORT is not set # # Character devices # CONFIG_VT=y CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set CONFIG_SERIAL_8250_AU1X00=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set # CONFIG_HW_RANDOM is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # # CONFIG_SSB is not set # # Multifunction device drivers # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set # # Multimedia devices # # # Multimedia core support # # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set # CONFIG_VIDEO_MEDIA is not set # # Multimedia drivers # # CONFIG_DAB is not set # # Alchemy MAE # CONFIG_AU13XX_MAE2=y CONFIG_ALCHEMY_MAE_ITE=y CONFIG_ALCHEMY_MAE_BSA=y CONFIG_ALCHEMY_MAE_MPE=y # # Graphics support # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set # CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set # CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # # Frame buffer hardware drivers # # CONFIG_FB_S1D13XXX is not set CONFIG_FB_AU1200=y # CONFIG_FB_VIRTUAL is not set # CONFIG_FB_METRONOME is not set # CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set # CONFIG_LOGO_LINUX_CLUT224 is not set CONFIG_LOGO_RMI_ALCHEMY_VGA16=y # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # # USB Input Devices # CONFIG_USB_HID=y # CONFIG_HID_PID is not set # CONFIG_USB_HIDDEV is not set # # Special HID drivers # CONFIG_HID_COMPAT=y # CONFIG_HID_A4TECH is not set # CONFIG_HID_APPLE is not set # CONFIG_HID_BELKIN is not set # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_GYRATION is not set # CONFIG_HID_LOGITECH is not set # CONFIG_HID_MICROSOFT is not set # CONFIG_HID_MONTEREY is not set # CONFIG_HID_NTRIG is not set # CONFIG_HID_PANTHERLORD is not set # CONFIG_HID_PETALYNX is not set # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set # CONFIG_GREENASIA_FF is not set # CONFIG_HID_TOPSEED is not set # CONFIG_THRUSTMASTER_FF is not set # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y CONFIG_USB_DEBUG=y CONFIG_USB_ANNOUNCE_NEW_DEVICES=y # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set # CONFIG_USB_MON is not set # CONFIG_USB_WUSB is not set # CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_OHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_HWA_HCD is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set # CONFIG_USB_WDM is not set # CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # # see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y CONFIG_USB_STORAGE_DEBUG=y # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y # # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # # USB port drivers # # CONFIG_USB_SERIAL is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set # CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_BERRY_CHARGE is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set # # OTG and related infrastructure # CONFIG_MMC=y CONFIG_MMC_DEBUG=y CONFIG_MMC_UNSAFE_RESUME=y # # MMC/SD/SDIO Card Drivers # CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set # CONFIG_MMC_TEST is not set # # MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set CONFIG_MMC_AU1X=y # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set CONFIG_RTC_LIB=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y # CONFIG_EXT2_FS_SECURITY is not set # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set CONFIG_CONFIGFS_FS=m CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_ECRYPT_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set CONFIG_CRAMFS=y CONFIG_SQUASHFS=y # CONFIG_SQUASHFS_EMBEDDED is not set CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3 # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y # CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y # CONFIG_DLM is not set # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_STACKTRACE=y # CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_SYSCTL_SYSCALL_CHECK is not set CONFIG_NOP_TRACER=y CONFIG_RING_BUFFER=y CONFIG_TRACING=y # # Tracers # CONFIG_DYNAMIC_PRINTK_DEBUG=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="console=ttyS0,115200" # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # # CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_TEST is not set # # Authenticated Encryption with Associated Data # # CONFIG_CRYPTO_CCM is not set # CONFIG_CRYPTO_GCM is not set # CONFIG_CRYPTO_SEQIV is not set # # Block modes # CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_CTR is not set # CONFIG_CRYPTO_CTS is not set CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_LRW=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_XTS is not set # # Hash modes # CONFIG_CRYPTO_HMAC=m CONFIG_CRYPTO_XCBC=m # # Digest # CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_MICHAEL_MIC=m # CONFIG_CRYPTO_RMD128 is not set # CONFIG_CRYPTO_RMD160 is not set # CONFIG_CRYPTO_RMD256 is not set # CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_WP512=m # # Ciphers # CONFIG_CRYPTO_AES=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_DES=y CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m # CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # # Compression # CONFIG_CRYPTO_DEFLATE=m # CONFIG_CRYPTO_LZO is not set # # Random Number Generation # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # # Library routines # CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set CONFIG_CRC_ITU_T=m CONFIG_CRC32=y # CONFIG_CRC7 is not set CONFIG_LIBCRC32C=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y ==================================================================================================================== Thanks Sanjay ^ permalink raw reply [flat|nested] 9+ messages in thread
* USB Root Hub and Bus getting suspended @ 2010-05-19 11:14 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-19 11:14 UTC (permalink / raw) To: linux-mips Hi, I have enabled debug messages in the configuration. The debug message shows that "root hub" and "bus" are finally getting suspended, this is preventing USB device detection. au1xxx-ohci au1xxx-ohci.0: auto-stop root hub hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend au1xxx-ohci au1xxx-ohci.0: suspend root hub hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend au13xx-ehci au13xx-ehci.0: suspend root hub Below is the complete debug message: ================================================================ ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 ehci->regs = b4020010 au13xx-ehci au13xx-ehci.0: Au13xx EHCI drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' au13xx-ehci au13xx-ehci.0: new USB bus registered, assigned bus number 1 au13xx-ehci au13xx-ehci.0: park 0 au13xx-ehci au13xx-ehci.0: irq 98, io mem 0x14020000 au13xx-ehci au13xx-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT au13xx-ehci au13xx-ehci.0: init command 010009 (park)=0 ithresh=1 period=256 RUN au13xx-ehci au13xx-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: default language 0x0409 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Au13xx EHCI usb usb1: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd usb usb1: SerialNumber: au13xx-ehci.0 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: individual port power switching hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports drivers/usb/core/inode.c: creating file '001' ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 64 td 64 In au13xx_start_ohc au1xxx-ohci au1xxx-ohci.0: Au13xx OHCI drivers/usb/core/inode.c: creating file '002' au1xxx-ohci au1xxx-ohci.0: new USB bus registered, assigned bus number 2 au1xxx-ohci au1xxx-ohci.0: irq 98, io mem 0x14020800 au1xxx-ohci au1xxx-ohci.0: ohci_au13xx_start, ohci:8fa1c4d8<7>au1xxx-ohci au1xxx-ohci.0: created debug files au1xxx-ohci au1xxx-ohci.0: OHCI controller state au1xxx-ohci au1xxx-ohci.0: OHCI 1.0, NO legacy support registers au1xxx-ohci au1xxx-ohci.0: control 0x083 HCFS=operational CBSR=3 au1xxx-ohci au1xxx-ohci.0: cmdstatus 0x00000 SOC=0 au1xxx-ohci au1xxx-ohci.0: intrstatus 0x00000004 SF au1xxx-ohci au1xxx-ohci.0: intrenable 0x8000001a MIE UE RD WDH au1xxx-ohci au1xxx-ohci.0: hcca frame #0005 au1xxx-ohci au1xxx-ohci.0: roothub.a 02000201 POTPGT=2 NPS NDP=1(1) au1xxx-ohci au1xxx-ohci.0: roothub.b 00000000 PPCM=0000 DR=0000 au1xxx-ohci au1xxx-ohci.0: roothub.status 00008000 DRWE au1xxx-ohci au1xxx-ohci.0: roothub.portstatus [0] 0x00000100 PPS usb usb2: default language 0x0409 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: Au13xx OHCI usb usb2: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ohci_hcd usb usb2: SerialNumber: au13xx usb usb2: uevent hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000 usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: global over-current protection hub 2-0:1.0: power on to power good time: 4ms hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: trying to enable port power on non-switchable hub drivers/usb/core/inode.c: creating file '001' Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000 Freeing unused kernel memory: 7008k freed au1xxx-ohci au1xxx-ohci.0: auto-stop root hub hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend au1xxx-ohci au1xxx-ohci.0: suspend root hub hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend au13xx-ehci au13xx-ehci.0: suspend root hub ================================================================ Any suggestion to troubleshoot this is highly appreciated. Thanks Sanjay -----Original Message----- From: Sanjay Kumar Sent: Mon 5/17/2010 8:23 PM To: linux-mips@linux-mips.org Subject: USB device not detected in Au1350 Hi , We are porting Linux to Au1350 board . We are using Yamon bootloader and Linux source code (2.6.29) of DB1300 board. Kenel is booting successfully on our board.Currently we are using initramfs. We have enabled USB support in the configuration file but USB device is not detected , however boot message shows that the USB drivers are loaded properly.It is detecting root hub and ports. After inserting USB device (pen drive) a device file shall be created in /dev ( like sda , sdb etc.) but its not happening in my case. /proc/devices has the following block devices: 1 ramdisk 259 blkext 7 loop 8 sd 11 sr 65 sd 66 sd 67 sd 68 sd 69 sd 70 sd 71 sd 128 sd 129 sd 130 sd 131 sd 132 sd 133 sd 134 sd 135 sd 179 mmc When tried to create block using mknod for the major nos mentioned (mknod /dev/sda b 135 0) , while mounting it says "/dev/sda" is not a valid block device. Similar result for other block devices too. /sys/block has following deveices , which are different from /proc/devices /sys/block# ls loop0 loop3 loop6 ram1 ram12 ram15 ram4 ram7 loop1 loop4 loop7 ram10 ram13 ram2 ram5 ram8 loop2 loop5 ram0 ram11 ram14 ram3 ram6 ram9 /proc/bus/usb/devices has the following: root@db1300:/proc/bus/usb# cat devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd S: Product=Au13xx EHCI S: SerialNumber=au13xx-ehci.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms Any suggestion where it could be going wrong ? Below is the boot message and kernel configuration I'm using. ========================================================================================================== Below is the boot message related to USB: Linux version 2.6.29.4-rmi-126-DB1300 (sanjayk@ubuntu) (gcc version 4.2.4) #0 Wed May 12 16:25:25 IST 2010 console [early0] enabled CPU revision is: 800c8001 (Au13xx) (PRId 800c8001) @ 396.00 MHz RMI DBAu1300 Development Board Determined physical RAM map: memory: 01800000 @ 00000000 (usable) memory: 0c800000 @ 01800000 (reserved) memory: 02000000 @ 0e000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,115200 video=au1200fb:panel:bs Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes PID hash table entries: 1024 (order: 10, 4096 bytes) Alchemy clocksource installed Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 42308k/57344k available (3360k kernel code, 14760k reserved, 796k data, 7008k init, 0k highmem) Calibrating delay loop... 395.67 BogoMIPS (lpj=1978368) Mount-cache hash table entries: 512 net_namespace: 296 bytes NET: Registered protocol family 16 Hooking cpu_wait bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Creating sysfs entry for board Alchemy MEMPOOL initializing Alchemy MEMPOOL registered at major 235 Available memory pools: LCD: 40 MB @ phys 0x01800000, free BSA: 64 MB @ phys 0x04000000, free MPE: 32 MB @ phys 0x08000000, free OGL: 64 MB @ phys 0x0a000000, free squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 83 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered au1200fb: LCD controller driver for AU1200 processors Returning LCD switch setting 0 au1200fb: Panel 0 Samsung 800x480 au1200fb: Win 2 0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx Panel(Samsung 800x480), 800x480 Returning LCD switch setting 0 IRQ 99/lcd: IRQF_DISABLED is not guaranteed on shared IRQs au1200fb: Allocating fb0: 800x480@16 bpp Console: switching to colour frame buffer device 100x30 au1200fb: Allocating fb1: 800x480@16 bpp au1200fb: Allocating fb2: 800x480@32 bpp au1200fb: Allocating fb3: 800x480@16 bpp Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.9: ttyS0 at MMIO 0x10102000 (irq = 33) is a 8250 console handover: boot [early0] -> real [ttyS0] brd: module loaded loop: module loaded smsc911x: Driver version 2008-10-21. MAEBE: physAddr 08000000, physSize 02000000 Au12XX MAEBE driver registered Sucessfully v1.0 Au13XX MAEBSA driver registered Sucessfully v1.0 Au13XX MAEMPE driver registered Sucessfully v1.0 mae_dma: pri0 45617238, pri1 09000000 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci->regs = b4020010 au13xx-ehci au13xx-ehci.0: Au13xx EHCI au13xx-ehci au13xx-ehci.0: new USB bus registered, assigned bus number 1 au13xx-ehci au13xx-ehci.0: irq 98, io mem 0x14020000 au13xx-ehci au13xx-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Au13xx EHCI usb usb1: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd usb usb1: SerialNumber: au13xx-ehci.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual Probing for MMC Probing for MMC mmc0 au1xxx-mmc: MMC Controller 0 set up at B0600000 (mode=dma) usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver oprofile: using timer interrupt. RMI Linux 271 db1300 ttyS0 db1300 login: ======================================================================================================================================= # # Automatically generated make config: don't edit # Linux kernel version: 2.6.29.4-rmi-126 # Wed May 19 13:52:45 2010 # CONFIG_MIPS=y # # Machine selection # CONFIG_MACH_ALCHEMY=y # CONFIG_BASLER_EXCITE is not set # CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set # CONFIG_LASAT is not set # CONFIG_LEMOTE_FULONG is not set # CONFIG_MIPS_MALTA is not set # CONFIG_MIPS_SIM is not set # CONFIG_NEC_MARKEINS is not set # CONFIG_MACH_VR41XX is not set # CONFIG_NXP_STB220 is not set # CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set # CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set # CONFIG_SIBYTE_CRHINE is not set # CONFIG_SIBYTE_CARMEL is not set # CONFIG_SIBYTE_CRHONE is not set # CONFIG_SIBYTE_RHONE is not set # CONFIG_SIBYTE_SWARM is not set # CONFIG_SIBYTE_LITTLESUR is not set # CONFIG_SIBYTE_SENTOSA is not set # CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set # CONFIG_MACH_TX39XX is not set # CONFIG_MACH_TX49XX is not set # CONFIG_MIKROTIK_RB532 is not set # CONFIG_WR_PPMC is not set # CONFIG_CAVIUM_OCTEON_SIMULATOR is not set # CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set # CONFIG_MIPS_MTX1 is not set # CONFIG_MIPS_BOSPORUS is not set # CONFIG_MIPS_DB1000 is not set # CONFIG_MIPS_DB1100 is not set # CONFIG_MIPS_DB1200 is not set # CONFIG_MIPS_HMP10 is not set # CONFIG_MIPS_DB1500 is not set # CONFIG_MIPS_DB1550 is not set CONFIG_MIPS_DB1300=y # CONFIG_MIPS_MIRAGE is not set # CONFIG_MIPS_PB1000 is not set # CONFIG_MIPS_PB1100 is not set # CONFIG_MIPS_PB1200 is not set # CONFIG_MIPS_PB1500 is not set # CONFIG_MIPS_PB1550 is not set # CONFIG_MIPS_XXS1500 is not set CONFIG_SOC_AU13XX=y CONFIG_SOC_AU1X00=y CONFIG_AU_GPIO_INT_CNTLR=y CONFIG_AU_MEMPOOL=y CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_OMIT_FRAME_POINTER=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_CEVT_R4K_LIB=y CONFIG_CSRC_R4K_LIB=y CONFIG_DMA_COHERENT=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y # CONFIG_HOTPLUG_CPU is not set # CONFIG_NO_IOPORT is not set # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y CONFIG_IRQ_CPU=y CONFIG_MIPS_L1_CACHE_SHIFT=5 # # CPU selection # # CONFIG_CPU_LOONGSON2 is not set CONFIG_CPU_MIPS32_R1=y # CONFIG_CPU_MIPS32_R2 is not set # CONFIG_CPU_MIPS64_R1 is not set # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set # CONFIG_CPU_VR41XX is not set # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set # CONFIG_CPU_R5000 is not set # CONFIG_CPU_R5432 is not set # CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set # CONFIG_CPU_R10000 is not set # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set # CONFIG_CPU_CAVIUM_OCTEON is not set CONFIG_SYS_HAS_CPU_MIPS32_R1=y CONFIG_CPU_MIPS32=y CONFIG_CPU_MIPSR1=y CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y CONFIG_HARDWARE_WATCHPOINTS=y # # Kernel type # CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT_DISABLED=y # CONFIG_MIPS_MT_SMP is not set # CONFIG_MIPS_MT_SMTC is not set CONFIG_64BIT_PHYS_ADDR=y CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y # CONFIG_HIGHMEM is not set CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_SYS_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y CONFIG_UNEVICTABLE_LRU=y # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set CONFIG_HZ_100=y # CONFIG_HZ_128 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_256 is not set # CONFIG_HZ_1000 is not set # CONFIG_HZ_1024 is not set CONFIG_SYS_SUPPORTS_ARBIT_HZ=y CONFIG_HZ=100 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set # CONFIG_KEXEC is not set CONFIG_SECCOMP=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_LOCALVERSION="-DB1300" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set # # RCU Subsystem # CONFIG_CLASSIC_RCU=y # CONFIG_TREE_RCU is not set # CONFIG_PREEMPT_RCU is not set # CONFIG_TREE_RCU_TRACE is not set # CONFIG_PREEMPT_RCU_TRACE is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_GROUP_SCHED is not set # CONFIG_CGROUPS is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set # CONFIG_NAMESPACES is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="/host/Project/AVN/Misc/kd/rootfs-tiny" CONFIG_INITRAMFS_ROOT_UID=0 CONFIG_INITRAMFS_ROOT_GID=0 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_PCSPKR_PLATFORM=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y CONFIG_MARKERS=y CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_BLOCK=y CONFIG_LBD=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_DEADLINE is not set # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_PROBE_INITRD_HEADER is not set CONFIG_FREEZER=y # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # # CONFIG_ARCH_SUPPORTS_MSI is not set CONFIG_MMU=y # CONFIG_PCCARD is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_TRAD_SIGNALS=y # # Power management options # CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_PM=y # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y CONFIG_SUSPEND_FREEZER=y # CONFIG_APM_EMULATION is not set CONFIG_NET=y # # Networking options # CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set # CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set # CONFIG_PHONET is not set # CONFIG_WIRELESS is not set # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set # # Device Drivers # # # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y CONFIG_FIRMWARE_IN_KERNEL=y CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=m # CONFIG_MTD_DEBUG is not set # CONFIG_MTD_CONCAT is not set # CONFIG_MTD_PARTITIONS is not set # CONFIG_MTD_TESTS is not set # # User Modules And Translation Layers # # CONFIG_MTD_CHAR is not set # CONFIG_MTD_BLKDEVS is not set # CONFIG_MTD_BLOCK is not set # CONFIG_MTD_BLOCK_RO is not set # CONFIG_FTL is not set # CONFIG_NFTL is not set # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set # CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers # # CONFIG_MTD_CFI is not set # CONFIG_MTD_JEDECPROBE is not set CONFIG_MTD_MAP_BANK_WIDTH_1=y CONFIG_MTD_MAP_BANK_WIDTH_2=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set # CONFIG_MTD_ABSENT is not set # # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set # CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers # # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set # CONFIG_MTD_BLOCK2MTD is not set # # Disk-On-Chip Device Drivers # # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set # CONFIG_MTD_NAND is not set # CONFIG_MTD_ONENAND is not set # # LPDDR flash memory drivers # # CONFIG_MTD_LPDDR is not set # # UBI - Unsorted block images # # CONFIG_MTD_UBI is not set # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # CONFIG_BLK_DEV_HD is not set # CONFIG_LBA_NAND is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y CONFIG_SCSI_DMA=y CONFIG_SCSI_TGT=y # CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set CONFIG_SCSI_SCAN_ASYNC=y CONFIG_SCSI_WAIT_SCAN=m # # SCSI Transports # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_LIBFC is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # CONFIG_VETH is not set CONFIG_PHYLIB=y # # MII PHY device drivers # # CONFIG_MARVELL_PHY is not set # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set # CONFIG_CICADA_PHY is not set # CONFIG_VITESSE_PHY is not set # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_AX88796 is not set # CONFIG_MIPS_AU1X00_ENET is not set # CONFIG_SMC91X is not set # CONFIG_DM9000 is not set CONFIG_SMSC911X=y # CONFIG_SMSC9210 is not set # CONFIG_DNET is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # # Wireless LAN # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set # CONFIG_IWLWIFI_LEDS is not set # # Enable WiMAX (Networking options) to see the WiMAX drivers # # # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set # # Userland interfaces # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set # # Hardware I/O ports # CONFIG_SERIO=y # CONFIG_SERIO_I8042 is not set CONFIG_SERIO_SERPORT=y CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=y # CONFIG_GAMEPORT is not set # # Character devices # CONFIG_VT=y CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set CONFIG_SERIAL_8250_AU1X00=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set # CONFIG_HW_RANDOM is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # # CONFIG_SSB is not set # # Multifunction device drivers # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set # # Multimedia devices # # # Multimedia core support # # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set # CONFIG_VIDEO_MEDIA is not set # # Multimedia drivers # # CONFIG_DAB is not set # # Alchemy MAE # CONFIG_AU13XX_MAE2=y CONFIG_ALCHEMY_MAE_ITE=y CONFIG_ALCHEMY_MAE_BSA=y CONFIG_ALCHEMY_MAE_MPE=y # # Graphics support # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set # CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set # CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # # Frame buffer hardware drivers # # CONFIG_FB_S1D13XXX is not set CONFIG_FB_AU1200=y # CONFIG_FB_VIRTUAL is not set # CONFIG_FB_METRONOME is not set # CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set # CONFIG_LOGO_LINUX_CLUT224 is not set CONFIG_LOGO_RMI_ALCHEMY_VGA16=y # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # # USB Input Devices # CONFIG_USB_HID=y # CONFIG_HID_PID is not set # CONFIG_USB_HIDDEV is not set # # Special HID drivers # CONFIG_HID_COMPAT=y # CONFIG_HID_A4TECH is not set # CONFIG_HID_APPLE is not set # CONFIG_HID_BELKIN is not set # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_GYRATION is not set # CONFIG_HID_LOGITECH is not set # CONFIG_HID_MICROSOFT is not set # CONFIG_HID_MONTEREY is not set # CONFIG_HID_NTRIG is not set # CONFIG_HID_PANTHERLORD is not set # CONFIG_HID_PETALYNX is not set # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set # CONFIG_GREENASIA_FF is not set # CONFIG_HID_TOPSEED is not set # CONFIG_THRUSTMASTER_FF is not set # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y CONFIG_USB_DEBUG=y CONFIG_USB_ANNOUNCE_NEW_DEVICES=y # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y CONFIG_USB_DEVICE_CLASS=y # CONFIG_USB_DYNAMIC_MINORS is not set CONFIG_USB_SUSPEND=y # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set CONFIG_USB_MON=y # CONFIG_USB_WUSB is not set # CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set CONFIG_USB_OHCI_HCD=y # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_HWA_HCD is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set # CONFIG_USB_WDM is not set # CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # # see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y CONFIG_USB_STORAGE_DEBUG=y # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y # # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # # USB port drivers # # CONFIG_USB_SERIAL is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set # CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_BERRY_CHARGE is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set # # OTG and related infrastructure # CONFIG_MMC=y CONFIG_MMC_DEBUG=y CONFIG_MMC_UNSAFE_RESUME=y # # MMC/SD/SDIO Card Drivers # CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set CONFIG_MMC_TEST=y # # MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set CONFIG_MMC_AU1X=y # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set CONFIG_RTC_LIB=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y # CONFIG_EXT2_FS_SECURITY is not set # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set CONFIG_CONFIGFS_FS=m CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_ECRYPT_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set # CONFIG_JFFS2_FS is not set CONFIG_CRAMFS=y CONFIG_SQUASHFS=y # CONFIG_SQUASHFS_EMBEDDED is not set CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3 # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y # CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y # CONFIG_DLM is not set # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_STACKTRACE=y # CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_SYSCTL_SYSCALL_CHECK is not set CONFIG_NOP_TRACER=y CONFIG_RING_BUFFER=y CONFIG_TRACING=y # # Tracers # CONFIG_DYNAMIC_PRINTK_DEBUG=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="console=ttyS0,115200" # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # # CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_TEST is not set # # Authenticated Encryption with Associated Data # # CONFIG_CRYPTO_CCM is not set # CONFIG_CRYPTO_GCM is not set # CONFIG_CRYPTO_SEQIV is not set # # Block modes # CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_CTR is not set # CONFIG_CRYPTO_CTS is not set CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_LRW=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_XTS is not set # # Hash modes # CONFIG_CRYPTO_HMAC=m CONFIG_CRYPTO_XCBC=m # # Digest # CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_MICHAEL_MIC=m # CONFIG_CRYPTO_RMD128 is not set # CONFIG_CRYPTO_RMD160 is not set # CONFIG_CRYPTO_RMD256 is not set # CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_WP512=m # # Ciphers # CONFIG_CRYPTO_AES=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_DES=y CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m # CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # # Compression # CONFIG_CRYPTO_DEFLATE=m # CONFIG_CRYPTO_LZO is not set # # Random Number Generation # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # # Library routines # CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set CONFIG_CRC_ITU_T=m CONFIG_CRC32=y # CONFIG_CRC7 is not set CONFIG_LIBCRC32C=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y ==================================================================================================================== Thanks Sanjay ^ permalink raw reply [flat|nested] 9+ messages in thread
* USB Root Hub and Bus getting suspended @ 2010-05-19 11:14 ` Sanjay Kumar 0 siblings, 0 replies; 9+ messages in thread From: Sanjay Kumar @ 2010-05-19 11:14 UTC (permalink / raw) To: linux-mips Hi, I have enabled debug messages in the configuration. The debug message shows that "root hub" and "bus" are finally getting suspended, this is preventing USB device detection. au1xxx-ohci au1xxx-ohci.0: auto-stop root hub hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend au1xxx-ohci au1xxx-ohci.0: suspend root hub hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend au13xx-ehci au13xx-ehci.0: suspend root hub Below is the complete debug message: ================================================================ ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 ehci->regs = b4020010 au13xx-ehci au13xx-ehci.0: Au13xx EHCI drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' au13xx-ehci au13xx-ehci.0: new USB bus registered, assigned bus number 1 au13xx-ehci au13xx-ehci.0: park 0 au13xx-ehci au13xx-ehci.0: irq 98, io mem 0x14020000 au13xx-ehci au13xx-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT au13xx-ehci au13xx-ehci.0: init command 010009 (park)=0 ithresh=1 period=256 RUN au13xx-ehci au13xx-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: default language 0x0409 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Au13xx EHCI usb usb1: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd usb usb1: SerialNumber: au13xx-ehci.0 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: individual port power switching hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports drivers/usb/core/inode.c: creating file '001' ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 64 td 64 In au13xx_start_ohc au1xxx-ohci au1xxx-ohci.0: Au13xx OHCI drivers/usb/core/inode.c: creating file '002' au1xxx-ohci au1xxx-ohci.0: new USB bus registered, assigned bus number 2 au1xxx-ohci au1xxx-ohci.0: irq 98, io mem 0x14020800 au1xxx-ohci au1xxx-ohci.0: ohci_au13xx_start, ohci:8fa1c4d8<7>au1xxx-ohci au1xxx-ohci.0: created debug files au1xxx-ohci au1xxx-ohci.0: OHCI controller state au1xxx-ohci au1xxx-ohci.0: OHCI 1.0, NO legacy support registers au1xxx-ohci au1xxx-ohci.0: control 0x083 HCFS=operational CBSR=3 au1xxx-ohci au1xxx-ohci.0: cmdstatus 0x00000 SOC=0 au1xxx-ohci au1xxx-ohci.0: intrstatus 0x00000004 SF au1xxx-ohci au1xxx-ohci.0: intrenable 0x8000001a MIE UE RD WDH au1xxx-ohci au1xxx-ohci.0: hcca frame #0005 au1xxx-ohci au1xxx-ohci.0: roothub.a 02000201 POTPGT=2 NPS NDP=1(1) au1xxx-ohci au1xxx-ohci.0: roothub.b 00000000 PPCM=0000 DR=0000 au1xxx-ohci au1xxx-ohci.0: roothub.status 00008000 DRWE au1xxx-ohci au1xxx-ohci.0: roothub.portstatus [0] 0x00000100 PPS usb usb2: default language 0x0409 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: Au13xx OHCI usb usb2: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ohci_hcd usb usb2: SerialNumber: au13xx usb usb2: uevent hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000 usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: global over-current protection hub 2-0:1.0: power on to power good time: 4ms hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: trying to enable port power on non-switchable hub drivers/usb/core/inode.c: creating file '001' Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000 Freeing unused kernel memory: 7008k freed au1xxx-ohci au1xxx-ohci.0: auto-stop root hub hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend au1xxx-ohci au1xxx-ohci.0: suspend root hub hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend au13xx-ehci au13xx-ehci.0: suspend root hub ================================================================ Any suggestion to troubleshoot this is highly appreciated. Thanks Sanjay -----Original Message----- From: Sanjay Kumar Sent: Mon 5/17/2010 8:23 PM To: linux-mips@linux-mips.org Subject: USB device not detected in Au1350 Hi , We are porting Linux to Au1350 board . We are using Yamon bootloader and Linux source code (2.6.29) of DB1300 board. Kenel is booting successfully on our board.Currently we are using initramfs. We have enabled USB support in the configuration file but USB device is not detected , however boot message shows that the USB drivers are loaded properly.It is detecting root hub and ports. After inserting USB device (pen drive) a device file shall be created in /dev ( like sda , sdb etc.) but its not happening in my case. /proc/devices has the following block devices: 1 ramdisk 259 blkext 7 loop 8 sd 11 sr 65 sd 66 sd 67 sd 68 sd 69 sd 70 sd 71 sd 128 sd 129 sd 130 sd 131 sd 132 sd 133 sd 134 sd 135 sd 179 mmc When tried to create block using mknod for the major nos mentioned (mknod /dev/sda b 135 0) , while mounting it says "/dev/sda" is not a valid block device. Similar result for other block devices too. /sys/block has following deveices , which are different from /proc/devices /sys/block# ls loop0 loop3 loop6 ram1 ram12 ram15 ram4 ram7 loop1 loop4 loop7 ram10 ram13 ram2 ram5 ram8 loop2 loop5 ram0 ram11 ram14 ram3 ram6 ram9 /proc/bus/usb/devices has the following: root@db1300:/proc/bus/usb# cat devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd S: Product=Au13xx EHCI S: SerialNumber=au13xx-ehci.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms Any suggestion where it could be going wrong ? Below is the boot message and kernel configuration I'm using. ========================================================================================================== Below is the boot message related to USB: Linux version 2.6.29.4-rmi-126-DB1300 (sanjayk@ubuntu) (gcc version 4.2.4) #0 Wed May 12 16:25:25 IST 2010 console [early0] enabled CPU revision is: 800c8001 (Au13xx) (PRId 800c8001) @ 396.00 MHz RMI DBAu1300 Development Board Determined physical RAM map: memory: 01800000 @ 00000000 (usable) memory: 0c800000 @ 01800000 (reserved) memory: 02000000 @ 0e000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,115200 video=au1200fb:panel:bs Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes PID hash table entries: 1024 (order: 10, 4096 bytes) Alchemy clocksource installed Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 42308k/57344k available (3360k kernel code, 14760k reserved, 796k data, 7008k init, 0k highmem) Calibrating delay loop... 395.67 BogoMIPS (lpj=1978368) Mount-cache hash table entries: 512 net_namespace: 296 bytes NET: Registered protocol family 16 Hooking cpu_wait bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Creating sysfs entry for board Alchemy MEMPOOL initializing Alchemy MEMPOOL registered at major 235 Available memory pools: LCD: 40 MB @ phys 0x01800000, free BSA: 64 MB @ phys 0x04000000, free MPE: 32 MB @ phys 0x08000000, free OGL: 64 MB @ phys 0x0a000000, free squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 83 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered au1200fb: LCD controller driver for AU1200 processors Returning LCD switch setting 0 au1200fb: Panel 0 Samsung 800x480 au1200fb: Win 2 0-FS gfx, 1-video, 2-ovly gfx, 3-ovly gfx Panel(Samsung 800x480), 800x480 Returning LCD switch setting 0 IRQ 99/lcd: IRQF_DISABLED is not guaranteed on shared IRQs au1200fb: Allocating fb0: 800x480@16 bpp Console: switching to colour frame buffer device 100x30 au1200fb: Allocating fb1: 800x480@16 bpp au1200fb: Allocating fb2: 800x480@32 bpp au1200fb: Allocating fb3: 800x480@16 bpp Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.9: ttyS0 at MMIO 0x10102000 (irq = 33) is a 8250 console handover: boot [early0] -> real [ttyS0] brd: module loaded loop: module loaded smsc911x: Driver version 2008-10-21. MAEBE: physAddr 08000000, physSize 02000000 Au12XX MAEBE driver registered Sucessfully v1.0 Au13XX MAEBSA driver registered Sucessfully v1.0 Au13XX MAEMPE driver registered Sucessfully v1.0 mae_dma: pri0 45617238, pri1 09000000 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci->regs = b4020010 au13xx-ehci au13xx-ehci.0: Au13xx EHCI au13xx-ehci au13xx-ehci.0: new USB bus registered, assigned bus number 1 au13xx-ehci au13xx-ehci.0: irq 98, io mem 0x14020000 au13xx-ehci au13xx-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Au13xx EHCI usb usb1: Manufacturer: Linux 2.6.29.4-rmi-126-DB1300 ehci_hcd usb usb1: SerialNumber: au13xx-ehci.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual Probing for MMC Probing for MMC mmc0 au1xxx-mmc: MMC Controller 0 set up at B0600000 (mode=dma) usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver oprofile: using timer interrupt. RMI Linux 271 db1300 ttyS0 db1300 login: ======================================================================================================================================= # # Automatically generated make config: don't edit # Linux kernel version: 2.6.29.4-rmi-126 # Wed May 19 13:52:45 2010 # CONFIG_MIPS=y # # Machine selection # CONFIG_MACH_ALCHEMY=y # CONFIG_BASLER_EXCITE is not set # CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set # CONFIG_LASAT is not set # CONFIG_LEMOTE_FULONG is not set # CONFIG_MIPS_MALTA is not set # CONFIG_MIPS_SIM is not set # CONFIG_NEC_MARKEINS is not set # CONFIG_MACH_VR41XX is not set # CONFIG_NXP_STB220 is not set # CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set # CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set # CONFIG_SIBYTE_CRHINE is not set # CONFIG_SIBYTE_CARMEL is not set # CONFIG_SIBYTE_CRHONE is not set # CONFIG_SIBYTE_RHONE is not set # CONFIG_SIBYTE_SWARM is not set # CONFIG_SIBYTE_LITTLESUR is not set # CONFIG_SIBYTE_SENTOSA is not set # CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set # CONFIG_MACH_TX39XX is not set # CONFIG_MACH_TX49XX is not set # CONFIG_MIKROTIK_RB532 is not set # CONFIG_WR_PPMC is not set # CONFIG_CAVIUM_OCTEON_SIMULATOR is not set # CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set # CONFIG_MIPS_MTX1 is not set # CONFIG_MIPS_BOSPORUS is not set # CONFIG_MIPS_DB1000 is not set # CONFIG_MIPS_DB1100 is not set # CONFIG_MIPS_DB1200 is not set # CONFIG_MIPS_HMP10 is not set # CONFIG_MIPS_DB1500 is not set # CONFIG_MIPS_DB1550 is not set CONFIG_MIPS_DB1300=y # CONFIG_MIPS_MIRAGE is not set # CONFIG_MIPS_PB1000 is not set # CONFIG_MIPS_PB1100 is not set # CONFIG_MIPS_PB1200 is not set # CONFIG_MIPS_PB1500 is not set # CONFIG_MIPS_PB1550 is not set # CONFIG_MIPS_XXS1500 is not set CONFIG_SOC_AU13XX=y CONFIG_SOC_AU1X00=y CONFIG_AU_GPIO_INT_CNTLR=y CONFIG_AU_MEMPOOL=y CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_OMIT_FRAME_POINTER=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_CEVT_R4K_LIB=y CONFIG_CSRC_R4K_LIB=y CONFIG_DMA_COHERENT=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y # CONFIG_HOTPLUG_CPU is not set # CONFIG_NO_IOPORT is not set # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y CONFIG_IRQ_CPU=y CONFIG_MIPS_L1_CACHE_SHIFT=5 # # CPU selection # # CONFIG_CPU_LOONGSON2 is not set CONFIG_CPU_MIPS32_R1=y # CONFIG_CPU_MIPS32_R2 is not set # CONFIG_CPU_MIPS64_R1 is not set # CONFIG_CPU_MIPS64_R2 is not set # CONFIG_CPU_R3000 is not set # CONFIG_CPU_TX39XX is not set # CONFIG_CPU_VR41XX is not set # CONFIG_CPU_R4300 is not set # CONFIG_CPU_R4X00 is not set # CONFIG_CPU_TX49XX is not set # CONFIG_CPU_R5000 is not set # CONFIG_CPU_R5432 is not set # CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set # CONFIG_CPU_R10000 is not set # CONFIG_CPU_RM7000 is not set # CONFIG_CPU_RM9000 is not set # CONFIG_CPU_SB1 is not set # CONFIG_CPU_CAVIUM_OCTEON is not set CONFIG_SYS_HAS_CPU_MIPS32_R1=y CONFIG_CPU_MIPS32=y CONFIG_CPU_MIPSR1=y CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y CONFIG_HARDWARE_WATCHPOINTS=y # # Kernel type # CONFIG_32BIT=y # CONFIG_64BIT is not set CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT_DISABLED=y # CONFIG_MIPS_MT_SMP is not set # CONFIG_MIPS_MT_SMTC is not set CONFIG_64BIT_PHYS_ADDR=y CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y # CONFIG_HIGHMEM is not set CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_SYS_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y CONFIG_UNEVICTABLE_LRU=y # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set CONFIG_HZ_100=y # CONFIG_HZ_128 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_256 is not set # CONFIG_HZ_1000 is not set # CONFIG_HZ_1024 is not set CONFIG_SYS_SUPPORTS_ARBIT_HZ=y CONFIG_HZ=100 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set # CONFIG_KEXEC is not set CONFIG_SECCOMP=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_LOCALVERSION="-DB1300" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set # # RCU Subsystem # CONFIG_CLASSIC_RCU=y # CONFIG_TREE_RCU is not set # CONFIG_PREEMPT_RCU is not set # CONFIG_TREE_RCU_TRACE is not set # CONFIG_PREEMPT_RCU_TRACE is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_GROUP_SCHED is not set # CONFIG_CGROUPS is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set # CONFIG_NAMESPACES is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="/host/Project/AVN/Misc/kd/rootfs-tiny" CONFIG_INITRAMFS_ROOT_UID=0 CONFIG_INITRAMFS_ROOT_GID=0 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_PCSPKR_PLATFORM=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y CONFIG_MARKERS=y CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_BLOCK=y CONFIG_LBD=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_DEADLINE is not set # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_PROBE_INITRD_HEADER is not set CONFIG_FREEZER=y # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # # CONFIG_ARCH_SUPPORTS_MSI is not set CONFIG_MMU=y # CONFIG_PCCARD is not set # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_TRAD_SIGNALS=y # # Power management options # CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_PM=y # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y CONFIG_SUSPEND_FREEZER=y # CONFIG_APM_EMULATION is not set CONFIG_NET=y # # Networking options # CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set # CONFIG_INET_TUNNEL is not set # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set # CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set # CONFIG_PHONET is not set # CONFIG_WIRELESS is not set # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set # # Device Drivers # # # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y CONFIG_FIRMWARE_IN_KERNEL=y CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=m # CONFIG_MTD_DEBUG is not set # CONFIG_MTD_CONCAT is not set # CONFIG_MTD_PARTITIONS is not set # CONFIG_MTD_TESTS is not set # # User Modules And Translation Layers # # CONFIG_MTD_CHAR is not set # CONFIG_MTD_BLKDEVS is not set # CONFIG_MTD_BLOCK is not set # CONFIG_MTD_BLOCK_RO is not set # CONFIG_FTL is not set # CONFIG_NFTL is not set # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set # CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers # # CONFIG_MTD_CFI is not set # CONFIG_MTD_JEDECPROBE is not set CONFIG_MTD_MAP_BANK_WIDTH_1=y CONFIG_MTD_MAP_BANK_WIDTH_2=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set # CONFIG_MTD_ABSENT is not set # # Mapping drivers for chip access # # CONFIG_MTD_COMPLEX_MAPPINGS is not set # CONFIG_MTD_PLATRAM is not set # # Self-contained MTD device drivers # # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set # CONFIG_MTD_BLOCK2MTD is not set # # Disk-On-Chip Device Drivers # # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set # CONFIG_MTD_NAND is not set # CONFIG_MTD_ONENAND is not set # # LPDDR flash memory drivers # # CONFIG_MTD_LPDDR is not set # # UBI - Unsorted block images # # CONFIG_MTD_UBI is not set # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # CONFIG_BLK_DEV_HD is not set # CONFIG_LBA_NAND is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y CONFIG_SCSI_DMA=y CONFIG_SCSI_TGT=y # CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set CONFIG_SCSI_SCAN_ASYNC=y CONFIG_SCSI_WAIT_SCAN=m # # SCSI Transports # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_LIBFC is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # CONFIG_VETH is not set CONFIG_PHYLIB=y # # MII PHY device drivers # # CONFIG_MARVELL_PHY is not set # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set # CONFIG_CICADA_PHY is not set # CONFIG_VITESSE_PHY is not set # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_AX88796 is not set # CONFIG_MIPS_AU1X00_ENET is not set # CONFIG_SMC91X is not set # CONFIG_DM9000 is not set CONFIG_SMSC911X=y # CONFIG_SMSC9210 is not set # CONFIG_DNET is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # # Wireless LAN # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set # CONFIG_IWLWIFI_LEDS is not set # # Enable WiMAX (Networking options) to see the WiMAX drivers # # # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set # # Userland interfaces # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set # # Hardware I/O ports # CONFIG_SERIO=y # CONFIG_SERIO_I8042 is not set CONFIG_SERIO_SERPORT=y CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=y # CONFIG_GAMEPORT is not set # # Character devices # CONFIG_VT=y CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set CONFIG_SERIAL_8250_AU1X00=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set # CONFIG_HW_RANDOM is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # # CONFIG_SSB is not set # # Multifunction device drivers # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set # # Multimedia devices # # # Multimedia core support # # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set # CONFIG_VIDEO_MEDIA is not set # # Multimedia drivers # # CONFIG_DAB is not set # # Alchemy MAE # CONFIG_AU13XX_MAE2=y CONFIG_ALCHEMY_MAE_ITE=y CONFIG_ALCHEMY_MAE_BSA=y CONFIG_ALCHEMY_MAE_MPE=y # # Graphics support # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set # CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set # CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set # CONFIG_FB_MODE_HELPERS is not set # CONFIG_FB_TILEBLITTING is not set # # Frame buffer hardware drivers # # CONFIG_FB_S1D13XXX is not set CONFIG_FB_AU1200=y # CONFIG_FB_VIRTUAL is not set # CONFIG_FB_METRONOME is not set # CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set # CONFIG_LOGO_LINUX_CLUT224 is not set CONFIG_LOGO_RMI_ALCHEMY_VGA16=y # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # # USB Input Devices # CONFIG_USB_HID=y # CONFIG_HID_PID is not set # CONFIG_USB_HIDDEV is not set # # Special HID drivers # CONFIG_HID_COMPAT=y # CONFIG_HID_A4TECH is not set # CONFIG_HID_APPLE is not set # CONFIG_HID_BELKIN is not set # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_GYRATION is not set # CONFIG_HID_LOGITECH is not set # CONFIG_HID_MICROSOFT is not set # CONFIG_HID_MONTEREY is not set # CONFIG_HID_NTRIG is not set # CONFIG_HID_PANTHERLORD is not set # CONFIG_HID_PETALYNX is not set # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set # CONFIG_GREENASIA_FF is not set # CONFIG_HID_TOPSEED is not set # CONFIG_THRUSTMASTER_FF is not set # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y CONFIG_USB_DEBUG=y CONFIG_USB_ANNOUNCE_NEW_DEVICES=y # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y CONFIG_USB_DEVICE_CLASS=y # CONFIG_USB_DYNAMIC_MINORS is not set CONFIG_USB_SUSPEND=y # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set CONFIG_USB_MON=y # CONFIG_USB_WUSB is not set # CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set CONFIG_USB_OHCI_HCD=y # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_HWA_HCD is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set # CONFIG_USB_WDM is not set # CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # # see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y CONFIG_USB_STORAGE_DEBUG=y # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y # # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # # USB port drivers # # CONFIG_USB_SERIAL is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set # CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_BERRY_CHARGE is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_PHIDGET is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set # # OTG and related infrastructure # CONFIG_MMC=y CONFIG_MMC_DEBUG=y CONFIG_MMC_UNSAFE_RESUME=y # # MMC/SD/SDIO Card Drivers # CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_SDIO_UART is not set CONFIG_MMC_TEST=y # # MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set CONFIG_MMC_AU1X=y # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set CONFIG_RTC_LIB=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set # # File systems # CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y # CONFIG_EXT2_FS_SECURITY is not set # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set CONFIG_CONFIGFS_FS=m CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_ECRYPT_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set # CONFIG_JFFS2_FS is not set CONFIG_CRAMFS=y CONFIG_SQUASHFS=y # CONFIG_SQUASHFS_EMBEDDED is not set CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3 # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y # CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y # CONFIG_DLM is not set # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_STACKTRACE=y # CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_SYSCTL_SYSCALL_CHECK is not set CONFIG_NOP_TRACER=y CONFIG_RING_BUFFER=y CONFIG_TRACING=y # # Tracers # CONFIG_DYNAMIC_PRINTK_DEBUG=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="console=ttyS0,115200" # # Security options # CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # # CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_TEST is not set # # Authenticated Encryption with Associated Data # # CONFIG_CRYPTO_CCM is not set # CONFIG_CRYPTO_GCM is not set # CONFIG_CRYPTO_SEQIV is not set # # Block modes # CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_CTR is not set # CONFIG_CRYPTO_CTS is not set CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_LRW=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_XTS is not set # # Hash modes # CONFIG_CRYPTO_HMAC=m CONFIG_CRYPTO_XCBC=m # # Digest # CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_MICHAEL_MIC=m # CONFIG_CRYPTO_RMD128 is not set # CONFIG_CRYPTO_RMD160 is not set # CONFIG_CRYPTO_RMD256 is not set # CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_WP512=m # # Ciphers # CONFIG_CRYPTO_AES=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_DES=y CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m # CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m # # Compression # CONFIG_CRYPTO_DEFLATE=m # CONFIG_CRYPTO_LZO is not set # # Random Number Generation # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # # Library routines # CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set CONFIG_CRC_ITU_T=m CONFIG_CRC32=y # CONFIG_CRC7 is not set CONFIG_LIBCRC32C=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y ==================================================================================================================== Thanks Sanjay ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2010-05-19 11:14 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2010-05-13 5:28 Linux on Au1350 using Yamon Sanjay Kumar 2010-05-13 5:28 ` Sanjay Kumar 2010-05-13 6:03 ` tiejun.chen 2010-05-13 6:49 ` Sanjay Kumar 2010-05-13 6:49 ` Sanjay Kumar 2010-05-17 11:23 ` USB device not detected in Au1350 Sanjay Kumar 2010-05-17 11:23 ` Sanjay Kumar 2010-05-19 11:14 ` USB Root Hub and Bus getting suspended Sanjay Kumar 2010-05-19 11:14 ` Sanjay Kumar
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.